Hikoki C 18DL Manuel utilisateur
- Catégorie
- Outils électroportatifs
- Taper
- Manuel utilisateur
Ce manuel convient également à
SAFETY INSTRUCTIONS AND INSTRUCTION MANUAL
WARNING
IMPROPER OR UNSAFE use of this power tool can result in death or serious bodily
injury!
This manual contains important information about product safety. Please read
and understand this manual BEFORE operating the power tool. Please keep this
manual available for other users and owners before they use the power tool. This
manual should be stored in safe place.
INSTRUCCIONES DE SEGURIDAD Y MANUAL DE INSTRUCCIONES
ADVERTENCIA
¡La utilización INAPROPIADA O PELIGROSA de esta herramienta eléctrica puede
resultar en lesiones de gravedad o la muerte!
Este manual contiene información importante sobre la seguridad del producto.
Lea y comprenda este manual ANTES de utilizar la herramienta eléctrica. Guarde
este manual para que puedan leerlo otras personas antes de utilizar la herramienta
eléctrica. Este manual debe ser guardado en un lugar seguro.
Model Cordless Circular Saw
Modèle Scie circulaire sans fil
Modelo Sierra circular a batería
INSTRUCTIONS DE SECURITE ET MODE D’EMPLOI
AVERTISSEMENT
Une utilisation INCORRECTE OU DANGEREUSE de cet outil motorisé peut entraîner
la mort ou de sérieuses blessures corporelles!
Ce mode d’emploi contient d’importantes informations à propos de la sécurité de
ce produit. Prière de lire et de comprendre ce mode d’emploi AVANT d’utiliser
l’outil motorisé. Garder ce mode d’emploi à la disponibilité des autres utilisateurs
et propriétaires avant qu’ils utilisent l’outil motorisé. Ce mode d’emploi doit être
conservé dans un endroit sûr.
C 18DL
Designed for operating in USA & Canada only.
When this product is used in areas other than the USA & Canada,
we cannot guarantee the product quality and performance.
01Eng_C18DL_US 8/6/12, 13:251
CONTENTS
TABLE DES MATIERES
ÍNDICE
Página
DESCRIPCIÓN FUNCIONAL .................................... 52
NOMENCLATURA ............................................... 52
ESPECIFICACIONES ............................................ 53
MONTAJE Y OPERACIÓN ....................................... 54
APLICACIONES ................................................... 54
MÉTODO DE EXTRACCIÓN E INSTALACIÓN DE
LA BATERÍA .................................................. 54
MÉTODO DE CARGA .......................................... 54
ANTES DE LA UTILIZACIÓN .............................. 57
AJUSTE DE LA SIERRA ANTES DE UTILIZARLA ...
57
OPERACIÓN ........................................................ 58
MONTAJE Y DESMONTAJE DE LA HOJA DE
SIERRA ......................................................... 60
FORMA DE CAMBIAR LA LÁMPARA ................. 61
MANTENIMIENTO E INSPECCIÓN ........................ 62
ACCESSORIOS ........................................................ 63
ACCESORIOS ESTÁNDAR ................................. 63
ACCESORIOS OPCIONALES .............................. 64
LISTA DE PIEZAS ..................................................... 66
Français
Español
Página
INFORMACIÓN IMPORTANTE SOBRE SEGURIDAD ........
44
SIGNIFICADO DE LAS PALABRAS DE SEÑALIZACIÓN ......
44
SEGURIDAD ............................................................. 44
ADVERTENCIAS DE SEGURIDAD GENERAL
DE LA HERRAMIENTA ELÉCTRICA ............ 44
INSTRUCCIONES DE SEGURIDAD PARA
TODAS LAS SIERRAS ................................. 46
INSTRUCCIONES DE SEGURIDAD ADICIONALES
PARA TODAS LAS SIERRAS ...........................
46
INSTRUCCIONES DE SEGURIDAD PARA SIERRAS
CON UN PROTECTOR DE PÉNDULO INTERNO ....
47
NORMAS ESPECÍFICOS DE SEGURIDAD ......... 47
INSTRUCCIONES IMPORTANTES PARA LA UTILIZACIÓN
DEL SIERRA CIRCULAR A BATERÍA .......................
48
INSTRUCCIONES IMPORTANTES DE SEGURIDAD
PARA EL CARGADOR DE BATERÍAS ...........
49
INSTRUCCIONES IMPORTANTES DE SEGURIDAD PARA
LA BATERÍA Y EL CARGADOR DE BATERÍAS
..... 50
ADVERTENCIA DE LA BATERÍA DE LITIO ......... 50
English
Page
IMPORTANT SAFETY INFORMATION ................. 3
MEANINGS OF SIGNAL WORDS ........................ 3
SAFETY ...................................................................... 3
GENERAL POWER TOOL SAFETY WARNINGS ...
3
SAFETY INSTRUCTIONS FOR ALL SAWS .......... 5
FURTHER SAFETY INSTRUCTIONS FOR ALL SAWS ...
5
SAFETY INSTRUCTIONS FOR SAWS WITH
INNER PENDULUM GUARD ......................... 6
SPECIFIC SAFETY RULES .................................... 6
IMPORTANT SAFETY INSTRUCTIONS FOR USE
OF THE CORDLESS CIRCULAR SAW ........... 7
IMPORTANT SAFETY INSTRUCTIONS FOR
BATTERY CHARGER ...................................... 7
IMPORTANT SAFETY INSTRUCTIONS FOR USE OF
THE BATTERY AND BATTERY CHARGER ............
8
CAUTION ON LITHIUM-ION BATTERY ................ 9
Page
FUNCTIONAL DESCRIPTION .................................. 10
NAME OF PARTS ................................................ 10
SPECIFICATIONS ................................................. 11
ASSEMBLY AND OPERATION ................................ 12
APPLICATIONS .................................................... 12
REMOVAL AND INSTALLATION METHOD OF BATTERY ...
12
CHARGING METHOD ......................................... 12
BEFORE USE ....................................................... 15
ADJUSTING THE SAW PRIOR TO USE ............. 15
OPERATION ......................................................... 16
MOUNTING AND DISMOUNTING THE SAW BLADE ....
18
REPLACING LIGHT BULB ................................... 19
MAINTENANCE AND INSPECTION ....................... 20
ACCESSORIES ......................................................... 21
STANDARD ACCESSORIES................................ 21
OPTIONAL ACCESSORIES ................................. 22
PART LIST ................................................................ 66
Page
DESCRIPTION FONCTIONNELLE ........................... 31
NOM DES PARTIES ............................................. 31
SPECIFICATIONS ................................................. 32
ASSEMBLAGE ET FONCTIONNEMENT ................ 33
UTILISATIONS ..................................................... 33
MÉTHODE DE RETRAIT ET D’INSTALLATION
DE LA BATTERIE .......................................... 33
MÉTHODE DE RECHARGE ................................. 33
AVANT L’UTILISATION ........................................ 36
RÉGLAGE DE LA SCIE AVANT L’UTILISATION ...
37
UTILISATION ....................................................... 37
MONTAGE ET DÉMONTAGE DE LA LAME DE SCIE ...
39
REMPLACEMENT DES AMPOULES DE LAMPE ...
40
ENTRETIEN ET INSPECTION .................................. 41
ACCESSOIRES ......................................................... 42
ACCESSOIRES STANDARD ................................ 42
ACCESSOIRES EN OPTION ................................ 43
LISTA DES PIÈCES .................................................. 66
Page
INFORMATIONS IMPORTANTES DE SÉCURITÉ ...
23
SIGNIFICATION DES MOTS D’AVERTISSEMENT ...
23
SECURITE ................................................................ 23
AVERTISSEMENTS DE SÉCURITÉ GÉNÉRAUX
CONCERNANT LES OUTILS ÉLECTRIQUES...
23
CONSIGNES DE SÉCURITÉ RELATIVES À
TOUTES LES SCIES ..................................... 25
CONSIGNES DE SÉCURITÉ COMPLÉMENTAIRES
RELATIVES
À
TOUTES LES SCIES ................ 25
CONSIGNES DE SÉCURITÉ RELATIVES AUX SCIES
AVEC PROTECTEUR À PENDULE INTERNE .......
26
REGLES DE SECURITE SPECIFIQUES ............... 26
CONSIGNES DE SÉCURITÉ IMPORTANTES POUR
L’UTILISATION DU SCIE CIRCULAIRE SANS FIL ...
27
CONSIGNES DE SÉCURITÉ IMPORTANTES
POUR LE CHARGEUR DE BATTERIE .......... 28
CONSIGNES DE SÉCURITÉ IMPORTANTES POUR L’UTILISATION
DE LA BATTERIE ET DU CHARGEUR DE BATTERIE
...... 29
PRÉCAUTIONS RELATIVES A LA BATTERIE AU
LITHIUM ION ................................................ 29
01Eng_C18DL_US 7/31/09, 16:112
English
3
IMPORTANT SAFETY INFORMATION
Read and understand all of the safety precautions, warnings and operating instructions in the Instruction Manual
before operating or maintaining this power tool.
Most accidents that result from power tool operation and maintenance are caused by the failure to observe basic
safety rules or precautions. An accident can often be avoided by recognizing a potentially hazardous situation
before it occurs, and by observing appropriate safety procedures.
Basic safety precautions are outlined in the “SAFETY” section of this Instruction Manual and in the sections which
contain the operation and maintenance instructions.
Hazards that must be avoided to prevent bodily injury or machine damage are identified by WARNINGS on the
power tool and in this Instruction Manual.
NEVER use this power tool in a manner that has not been specifically recommended by HITACHI.
MEANINGS OF SIGNAL WORDS
WARNING indicates a potentially hazardous situations which, if ignored, could result in death or serious injury.
CAUTION indicates a potentially hazardous situations which, if not avoided, may result in minor or moderate
injury, or may cause machine damage.
NOTE emphasizes essential information.
SAFETY
GENERAL POWER TOOL SAFETY WARNINGS
WARNING:
Read all safety warnings and all instructions.
Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
The term “power tool” in the warnings refers to your mains-operated (corded) power tool or battery-operated
(cordless) power tool.
1) Work area safety
a) Keep work area clean and well lit.
Cluttered or dark areas invite accidents.
b) Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust.
Power tools create sparks which may ignite
the dust or fumes.
c) Keep children and bystanders away while
operating a power tool.
Distractions can cause you to lose control.
2) Electrical safety
a) Power tool plugs must match the outlet.
Never modify the plug in any way.
Do not use any adapter plugs with earthed
(grounded) power tools.
Unmodified plugs and matching outlets will
reduce risk of electric shock.
b) Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators.
There is an increased risk of electric shock if
your body is earthed or grounded.
c) Do not expose power tools to rain or wet
conditions.
Water entering a power tool will increase the
risk of electric shock.
d) Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges
or moving parts.
Damaged or entangled cords increase the risk
of electric shock.
e) When operating a power tool outdoors, use
an extension cord suitable for outdoor use.
Use of a cord suitable for outdoor use reduces
the risk of electric shock.
f) If operating a power tool in a damp location
is unavoidable, use a residual current device
(RCD) protected supply.
Use of an RCD reduces the risk of electric shock.
3) Personal safety
a) Stay alert, watch what you are doing and use
common sense when operating a power tool.
Do not use a power tool while you are tired
or under the influence of drugs, alcohol or
medication.
01Eng_C18DL_US 8/6/12, 13:333
4
English
A moment of inattention while operating
power tools may result in serious personal
injury.
b) Use personal protective equipment. Always
wear eye protection.
Protective equipment such as dust mask, non-
skid safety shoes, hard hat, or hearing
protection used for appropriate conditions
will reduce personal injuries.
c) Prevent unintentional starting. Ensure the
switch is in the off-position before connecting
to power source and/or battery pack, picking
up or carrying the tool.
Carrying power tools with your finger on the
switch or energising power tools that have
the switch on invites accidents.
d) Remove any adjusting key or wrench before
turning the power tool on.
A wrench or a key left attached to a rotating
part of the power tool may result in personal
injury.
e) Do not overreach. Keep proper footing and
balance at all times.
This enables better control of the power tool
in unexpected situations.
f) Dress properly. Do not wear loose clothing
or jewellery. Keep your hair, clothing and
gloves away from moving parts.
Loose clothes, jewellery or long hair can be
caught in moving parts.
g) If devices are provided for the connection of
dust extraction and collection facilities,
ensure these are connected and properly
used.
Use of dust collection can reduce dust-related
hazards.
4) Power tool use and care
a) Do not force the power tool. Use the correct
power tool for your application.
The correct power tool will do the job better
and safer at the rate for which it was designed.
b) Do not use the power tool if the switch does
not turn it on and off.
Any power tool that cannot be controlled with
the switch is dangerous and must be repaired.
c) Disconnect the plug from the power source
and/or the battery pack from the power tool
before making any adjustments, changing
accessories, or storing power tools.
Such preventive safety measures reduce the
risk of starting the power tool accidentally.
d) Store idle power tools out of the reach of
children and do not allow persons unfamiliar
with the power tool or these instructions to
operate the power tool.
Power tools are dangerous in the hands of
untrained users.
e) Maintain power tools. Check for
misalignment or binding of moving parts,
breakage of parts and any other condition
that may affect the power tool’s operation.
If damaged, have the power tool repaired
before use.
Many accidents are caused by poorly
maintained power tools.
f) Keep cutting tools sharp and clean.
Properly maintained cutting tools with sharp
cutting edges are less likely to bind and are
easier to control.
g) Use the power tool, accessories and tool bits
etc. in accordance with these instructions,
taking into account the working conditions
and the work to be performed.
Use of the power tool for operations different
from those intended could result in a
hazardous situation.
5) Battery tool use and care
a) Recharge only with the charger specified by
the manufacturer.
A charger that is suitable for one type of
battery pack may create a risk of fire when
used with another battery pack.
b) Use power tools only with specifically
designated battery packs.
Use of any other battery packs may create a
risk of injury and fire.
c) When battery pack is not in use, keep it away
from other metal objects like paper clips,
coins, keys, nails, screws, or other small
metal objects, that can make a connection
from one terminal to another.
Shorting the battery terminals together may
cause burns or a fire.
d) Under abusive conditions, liquid may be
ejected from the battery; avoid contact. If
contact accidentally occurs, flush with water.
If liquid contacts eyes, additionally seek
medical help. Liquid ejected from the battery
may cause irritation or burns.
6) Service
a) Have your power tool serviced by a qualified
repair person using only identical
replacement parts.
This will ensure that the safety of the power
tool is maintained.
01Eng_C18DL_US 7/31/09, 16:114
English
5
WARNING:
Some dust created by power sanding, sawing,
grinding, drilling, and other construction activities
contains chemicals known to the State of California
to cause cancer, birth defects or other reproductive
harm. Some examples of these chemicals are:
●
Lead from lead-based paints,
●
Crystalline silica from bricks and cement and other
masonry products, and
●
Arsenic and chromium from chemically-treated
lumber.
Your risk from these exposures varies, depending
on how often you do this type of work. To reduce
your exposure to these chemicals: work in a well
ventilated area, and work with approved safety
equipment, such as those dust masks that are
specially designed to filter out microscopic particles.
SAFETY INSTRUCTIONS FOR ALL SAWS
DANGER!
a) Keep hands away from cutting area and the blade.
Keep your second hand on auxiliary handle, or
motor housing.
If both hands are holding the saw, they cannot be
cut by the blade.
b) Do not reach underneath the workpiece.
The guard cannot protect you from the blade below
the workpiece.
c) Adjust the cutting depth to the thickness of the
workpiece.
Less than a full tooth of the blade teeth should be
visible below the workpiece.
d) Never hold piece being cut in your hands or across
your leg. Secure the workpiece to a stable
platform.
It is important to support the work properly to
minimize body exposure, blade binding, or loss of
control.
e) Hold power tool by insulated gripping surfaces
when performing an operation where the cutting
tool may contact hidden wiring or its own cord.
Contact with a “live” wire will also make exposed
metal parts of the power tool “live” and shock the
operator.
f) When ripping always use a rip fence or straight
edge guide.
This improves the accuracy of cut and reduces the
chance of blade binding.
g) Always use blades with correct size and shape
(diamond versus round) of arbour holes.
Blades that do not match the mounting hardware of
the saw will run eccentrically, causing loss of control.
h) Never use damaged or incorrect blade washers
or bolt.
The blade washers and bolt were specially
designed for your saw, for optimum performance
and safety of operation.
䡬
Never use any abrasive wheels
Burst of abrasive wheel cause serious injury of
operator or persons around the working area.
FURTHER SAFETY INSTRUCTIONS FOR
ALL SAWS
Causes and operator prevention of kickback:
–Kickback is a sudden reaction to a pinched, bound
or misaligned saw blade, causing an uncontrolled
saw to lift up and out of the workpiece toward the
operator.
– When the blade is pinched or bound tightly by the
kerf closing down, the blade stalls and the motor
reaction drives the unit rapidly back toward the
operator.
–If the blade becomes twisted or misaligned in the
cut, the teeth at the back edge of the blade can dig
into the top surface of the wood causing the blade
to climb out of the kerf and jump back toward the
operator.
Kickback is the result of saw misuse and/or incorrect
operating procedures or conditions and can be avoided
by taking proper precautions as given below.
a) Maintain a firm grip with both hands on the saw
and position your arms to resist kickback forces.
Position your body to either side of the blade, but
not in line with the blade.
Kickback could cause the saw to jump backwards,
but kickback forces can be controlled by the
operator, if proper precautions are taken.
b) When blade is binding, or when interrupting a cut
for any reason, release the trigger and hold the
saw motionless in the material until the blade
comes to a complete stop.
Never attempt to remove the saw from the work
or pull the saw backward while the blade is in
motion or kickback may occur.
Investigate and take corrective actions to eliminate
the cause of blade binding.
c) When restarting a saw in the workpiece, centre
the saw blade in the kerf and check that saw teeth
are not engaged into the material.
If saw blade is binding, it may walk up or kickback
from the workpiece as the saw is restarted.
d) Support large panels to minimize the risk of blade
pinching and kickback.
Large panels tend to sag under their own weight.
Supports must be placed under the panel on both
sides, near the line of cut and near the edge of the
panel.
e) Do not use dull or damaged blades.
Unsharpened or improperly set blades produce
narrow kerf causing excessive friction, blade
binding and kickback.
01Eng_C18DL_US 7/31/09, 16:115
6
English
f) Blade depth and bevel adjusting locking levers
must be tight and secure before making cut.
If blade adjustment shifts while cutting, it may
cause binding and kickback.
g) Use extra caution when making a “plunge cut”
into existing walls or other blind areas.
The protruding blade may cut objects that can
cause kickback.
SAFETY INSTRUCTIONS FOR SAWS WITH
INNER PENDULUM GUARD
a) Check lower guard for proper closing before each
use. Do not operate the saw if lower guard does
not move freely and close instantly. Never clamp
or tie the lower guard into the open position.
If saw is accidentally dropped, lower guard may
be bent.
Raise the lower guard with the retracting handle
and make sure it moves freely and does not touch
the blade or any other part, in all angles and depth
of cut.
b) Check the operation of the lower guard spring. If
the guard and the spring are not operating
properly, they must be serviced before use.
Lower guard may operate sluggishly due to
damaged parts, gummy deposits, or build-up of
debris.
c) Lower guard should be retracted manually only
for special cuts such as “plunge cuts” and
“compound cuts”. Raise lower guard by retracting
handle and as soon as blade enters the material,
the lower guard must be released.
For all other sawing, the lower guard should
operate automatically.
d) Always observe that the lower guard is covering
the blade before placing saw down on bench or
floor.
An unprotected, coasting blade will cause the saw
to walk backwards, cutting whatever is in its path.
Be aware of the time it takes for the blade to stop
after switch is released.
SPECIFIC SAFETY RULES
1. NEVER hold piece being cut in your hands or
across your leg. It is important to support the work
properly to minimize body exposure, blade
binding, or loss of control.
2. Hold tool by insulated gripping surfaces when
performing an operation where the cutting tool
may contact hidden wiring. Contact with a “live”
wire will also make exposed metal parts of the tool
“live” and shock the operator.
3. When ripping always use a rip fence or straight
edge guide. This improves the accuracy of cut and
reduces the chance for blade binding.
4. Always use blades with correct size and shape
(diamond vs. round) arbor holes. Blades that do
not match the mounting hardware of the saw will
run eccentrically, causing loss of control.
5. Never use damaged or incorrect blade washers
or bolts. The blade washers and bolt were specially
designed for your saw, for optimum performance
and safety of operation.
6. Hold tools by insulated gripping surfaces when
performing an operation where the cutting tool
may contact hidden wiring or its own cord. Contact
with a “live” wire will make exposed metal parts
of the tool “live” and shock the operator.
7. Never touch moving parts.
Never place your hands, fingers or other body parts
near the tool’s moving parts.
8. Never operate without all guards in place.
Never operate this tool without all guards or safety
features in place and in proper working order. If
maintenance or servicing requires the removal of
a guard or safety feature, be sure to replace the
guard or safety feature before resuming operation
of the tool.
9. Use right tool.
Don’t force small tool or attachment to do the job
of a heavy-duty tool.
Don’t use tool for purpose not intended —for
example— don’t use circular saw for cutting tree
limbs or logs.
10. Never use a power tool for applications other than
those specified.
Never use a power tool for applications other than
those specified in the Instruction Manual.
11. Handle tool correctly.
Operate the tool according to the instructions
provided herein. Do not drop or throw the tool.
Never allow the tool to be operated by children,
individuals unfamiliar with its operation or
unauthorized personnel.
12. Definitions for symbols.
V ............... volts
— ..............
direct current
---
n
o
.............. no load speed
---/min ...... revolutions or reciprocation per
minute
13. Keep all screws, bolts and covers tightly in place.
Keep all screws, bolts, and plates tightly mounted.
Check their condition periodically.
14. Do not use power tools if the plastic housing or
handle is cracked.
Cracks in the tool’s housing or handle can lead to
electric shock. Such tools should not be used until
repaired.
15. Blades and accessories must be securely mounted
to the tool.
Prevent potential injuries to yourself or others.
Blades, cutting implements and accessories which
have been mounted to the tool should be secure
and tight.
01Eng_C18DL_US 7/31/09, 16:116
English
7
16. Never use a tool which is defective or operating
abnormally.
If the tool appears to be operating unusually,
making strange noises, or otherwise appears
defective, stop using it immediately and arrange
for repairs by a Hitachi authorized service center.
17. Carefully handle power tools.
Should a power tool be dropped or struck against
hard materials inadvertently, it may be deformed,
cracked, or damaged.
18. Do not wipe plastic parts with solvent.
Solvents such as gasoline, thinner benzine, carbon
tetrachloride, and alcohol may damage and crack
plastic parts. Do not wipe them with such solvents.
Wipe plastic parts with a soft cloth lightly
dampened with soapy water and dried thoroughly.
IMPORTANT SAFETY INSTRUCTIONS FOR
USE OF THE CORDLESS CIRCULAR SAW
WARNING:
Death or serious bodily injury could result from
improper or unsafe use of the cordless circular
saw. To avoid these risks, follow these basic safety
instructions:
1. Wear ear plugs when using the tool for extended
periods. Prolonged exposure to high intensity
noise can cause hearing loss.
2. Never wedge or tie lower guard open. Check
operation of lower guard before each use. Do not
use if lower guard does not close briskly over saw
blade.
CAUTION:
If saw is dropped, safety cover may be bent
restricting full return.
3. For this mode, the saw blades range should be
from 165 mm to 160 mm.
4. Never place hands or other body parts near the
saw blade during operation. Hold the circular saw
by its handle only.
5. Because the cordless circular saw operates by
battery power, be aware of the fact that it can begin
to operate at any time.
6. Wear eye and ear protection at all times.
7. When working at elevated locations, clear the area
of other people and aware of conditions below you.
8. It is important to support the work properly and to
hold the saw firmly to prevent loss of control which
could cause personal injury.
9. Guard against kickback: Kickback occurs when the
saw stalls rapidly and is driven back towards the
operator. Release switch immediately if blade
binds or saw stalls.
•
Keep blades sharp.
•
Support the panel near the cut.
•
Use guide when ripping.
•
Don’t force tool.
•
Stay alert exercise control
•
Don’t remove saw from work during a cut while
the blade is moving.
10. In operating, keep hold main body firmly.
11. Keep the light ON during cutting operation only.
If it is lit ON in other cases, the main body switch
can be inadvertently turned ON, resulting in
unexpected accidents.
IMPORTANT SAFETY INSTRUCTIONS FOR
BATTERY CHARGER
WARNING:
Death or serious bodily injury could result from
improper or unsafe use of battery chargers. To
avoid these risks, follow these basic safety
instructions:
READ ALL INSTRUCTIONS
1. This manual contains important safety and
operating instructions for battery charger Model
UC18YRL, UC18YFL and UC18YGL2.
2. Before using battery charger, read all instructions
and cautionary markings on (1) battery charger,
(2) battery, and (3) product using battery.
3. To reduce risk of injury, charge HITACHI rechargeable
battery type EB7, EB9, EB12, EB14, EB18, BCL14,
BCL18 and EBM18 series. Other type of batteries may
burst causing personal injury and damage.
4. Do not expose battery charger to rain or snow.
5. Use of an attachment not recommended or sold
by the battery charger manufacturer may result in
a risk of fire, electric shock, or injury to persons.
6. To reduce risk of damage to electric plug and cord,
pull by plug when disconnecting battery charger.
7. Make sure cord is located so that it will not be
stepped on, tripped over, or otherwise subjected
to damage or stress.
8. An extension cord should not be used unless
absolutely necessary. Use of improper extension
cord could result in a risk of fire and electric shock.
If extension cord must be used make sure:
a. That blades of extension cord are the same
number, size, and shape as those of plug on
battery charger:
b. That extension cord is properly wired and in
good electrical condition; and
c. That wire size is large enough for AC ampere
rating of battery charger as specified in Table
1.
01Eng_C18DL_US 7/31/09, 16:127
8
English
Table 1
RECOMMENDED MINIMUM AWG SIZE FOR
EXTENSION CORDS FOR BATTERY CHARGERS
AC Input Rating Amperes* AWG Size of Cord
Equal to or but less Length of Cord, Feet (Meter)
greater than than 25 (7.5) 50 (15) 100 (30) 150 (45)
02 1818 18 16
23 1818 16 14
34 1818 16 14
* If the input rating of a battery charger is given in
watts rather than in amperes, the corresponding
ampere rating is to be determined by dividing the
wattage rating by the voltage rating–for example:
9. Do not operate battery charger with damaged cord
or plug-replace them immediately.
10. Do not operate battery charger if it has received a
sharp blow, been dropped, or otherwise damaged
in any way; take it to a qualified serviceman.
11. Do not disassemble battery charger; take it to a
qualified serviceman when service or repair is
required. Incorrect reassembly may result in a risk
of electric shock or fire.
12. To reduce risk of electric shock, unplug charger
from receptacle before attempting any
maintenance or cleaning. Removing the battery
will not reduce this risk.
13. This battery charger might be attached to HITACHI
battery operated tools as a standard accessory. In
this case, please confirm instruction Manual of the
HITACHI battery operated tools before using the
battery charger.
IMPORTANT SAFETY INSTRUCTIONS FOR
USE OF THE BATTERY AND BATTERY
CHARGER
You must charge the battery before you can use the
power tool. Before using the model
UC18YRL or UC18YFL or UC18YGL2 battery charger,
be sure to read all instructions and cautionary
statements on it, the battery and in this manual.
REMEMBER: USE ONLY HITACHI BATTERY TYPES EB7
SERIES, EB9 SERIES, EB12 SERIES, EB14 SERIES, EB18
SERIES, BCL14 SERIES, BCL18 SERIES AND EBM18
SERIES. OTHER TYPES OF BATTERIES MAY BURST
AND CAUSE INJURY!
Follow these instructions to avoid the risk of injury:
WARNING:
Improper use of the battery or battery charger can
lead to serious injury. To avoid these injuries:
1. NEVER disassemble the battery.
2. NEVER incinerate the battery, even if it is damaged
or is completely worn out. The battery can explode
in a fire.
3. NEVER short-circuit the battery.
4. NEVER insert any objects into the battery charger’s
air vents. Electric shock or damage to the battery
charger may result.
5. NEVER charge outdoors. Keep the battery away
from direct sunlight and use only where there is
low humidity and good ventilation.
6. NEVER charge when the temperature is below 32°F
(0°C) or above 104°F (40°C).
7. NEVER connect two battery chargers together.
8. NEVER insert foreign objects into the hole for the
battery or the battery charger.
9. NEVER use a booster transformer when charging.
10. NEVER use an engine generator or DC power to
charge.
11. NEVER store the battery or battery charger in
places where the temperature may reach or exceed
104°F (40°C).
12. ALWAYS operate charger on standard household
electrical power (120 volts). Using the charger on
any other voltage may overheat and damage the
charger.
13. ALWAYS wait at least 15 minutes between charges
to avoid overheating the charger.
14. ALWAYS disconnect the power cord from its
receptacle when the charger is not in use.
1,250 watts
125 volts
=
10 amperes
01Eng_C18DL_US 7/31/09, 16:128
English
9
CAUTION ON LITHIUM-ION BATTERY
To extend the lifetime, the lithium-ion battery equips
with the protection function to stop the output.
In the cases of 1 to 3 described below, when using this
product, even if you are pulling the switch, the motor
may stop. This is not the trouble but the result of
protection function.
1. When the battery power remaining runs out, the
motor stops.
In such case, charge it up immediately.
2. If the tool is overloaded, the motor may stop. In
this case, release the switch of tool and eliminate
causes of overloading. After that, you can use it
again.
3. If the battery is overheated under overload work,
the battery power may stop.
In this case, stop using the battery and let the
battery cool. After that, you can use it again.
Furthermore, please heed the following warning and
caution.
WARNING
In order to prevent any battery leakage, heat generation,
smoke emission, explosion and ignition beforehand,
please be sure to heed the following precautions.
1. Make sure that swarf and dust do not collect on
the battery.
䡬
During work make sure that swarf and dust do not
fall on the battery.
䡬
Make sure that any swarf and dust falling on the
power tool during work do not collect on the
battery.
䡬
Do not store an unused battery in a location
exposed to swarf and dust.
䡬
Before storing a battery, remove any swarf and
dust that may adhere to it and do not store it
together with metal parts (screws, nails, etc.).
2. Do not pierce battery with a sharp object such as a
nail, strike with a hammer, step on, throw or
subject the battery to severe physical shock.
3. Do not use an apparently damaged or deformed
battery.
4. Do not use the battery in reverse polarity.
5. Do not connect directly to an electrical outlets or
car cigarette lighter sockets.
6. Do not use the battery for a purpose other than
those specified.
7. If the battery charging fails to complete even when
a specified recharging time has elapsed,
immediately stop further recharging.
8. Do not put or subject the battery to high
temperatures or high pressure such as into a
microwave oven, dryer, or high pressure container.
9. Keep away from fire immediately when leakage
or foul odor are detected.
10. Do not use in a location where strong static
electricity generates.
11. If there is battery leakage, foul odor, heat
generated, discolored or deformed, or in any way
appears abnormal during use, recharging or
storage, immediately remove it from the
equipment or battery charger, and stop use.
CAUTION
1. If liquid leaking from the battery gets into your
eyes, do not rub your eyes and wash them well
with fresh clean water such as tap water and
contact a doctor immediately.
If left untreated, the liquid may cause eye-
problems.
2. If liquid leaks onto your skin or clothes, wash well
with clean water such as tap water immediately.
There is a possibility that this can cause skin
irritation.
3. If you find rust, foul odor, overheating, discolor,
deformation, and/or other irregularities when using
the battery for the first time, do not use and return
it to your supplier or vendor.
SAVE THESE INSTRUCTIONS
AND
MAKE THEM AVAILABLE TO OTHER USERS
AND
OWNERS OF THIS TOOL!
01Eng_C18DL_US 7/31/09, 16:129
10
English
FUNCTIONAL DESCRIPTION
NOTE:
The information contained in this Instruction Manual is designed to assist you in the safe operation and
maintenance of the power tool.
NEVER operate, or attempt any maintenance on the tool unless you have first read and understood all safety
instructions contained in this manual.
Some illustrations in this Instruction Manual may show details or attachments that differ from those on your
own power tool.
NAME OF PARTS
1. Cordless Circular Saw (C18DL)
䡬
Battery
<EBM1830> <BCL1815>
Fig. 1
Terminal hole
Nameplate
Latch
Wing-bolt
Bevel plate
Inclined gauge
Switch lock
Lock lever
Housing
Switch trigger
Battery
Wing-nut
Saw blade
Guide
Washer (B2)
Left-hand bolt
Lower guard
Nameplate
Base
Light cover
Light bulb
Terminal Hole
Latch
Nameplate
01Eng_C18DL_US 7/31/09, 16:1210
English
11
2. Battery Charger
<UC18YRL, UC18YFL> <UC18YGL2>
Fig. 2 Fig. 3
Overheat lamp (green)
Nameplate
Caution plate
Body
Battery installation hole
Charge status lamp (red)
Pilot lamp
Nameplate
Body
Battery
installation
hole
SPECIFICATIONS
1. Cordless Circular Saw (C18DL)
2. Battery Charger
Motor DC motor
No-load speed 3,400/min
Max. Cutting Depth 2-1/4” (57 mm)
Blade Size 6-1/2” (165 mm) D × 5/8” (15.9 mm) H × 1/16” (1.6 mm) T
Model EBM1830 BCL1815
Battery Type Lithium – ion battery
Voltage DC 18V
Light Bulb 12V, 5W
Weight 7.1 lbs. (3.2 kg) 6.6 lbs. (3.0 kg)
Model UC18YRL/UC18YFL UC18YGL2
Input power source Single phase: AC120V 60Hz
Charging time Approx. 20 min. .....BCL1815 Approx. 40 min. .....BCL1815
(At a temperature of 68°F (20°C)) Approx. 45 min. .....EBM1830 Approx. 90 min. .....EBM1830
Charging voltage DC 7.2 – 18V
Charging current DC 3.5A DC 2.0A
Weight 1.3 lbs. (0.6 kg) 0.9 lbs. (0.4 kg)
NOTE: The charging time may vary according to ambient temperature and power source voltage.
01Eng_C18DL_US 7/31/09, 16:1211
12
English
ASSEMBLY AND OPERATION
APPLICATIONS
䡬
Cutting various types of wood.
REMOVAL AND INSTALLATION METHOD
OF BATTERY
䡬
How to install the battery.
Align the battery with the groove in tool handle
and install it into place.
Always insert it all the way until it locks in place
with a little click, If not, it may accidentally fall out
of the tool, causing injury to you or someone
around you (Fig. 4).
Fig. 4
䡬
How to remove the battery.
Withdraw battery from the tool handle while
pressing the latches on both sides of the battery
(Fig. 4).
CHARGING METHOD
NOTE
Before plugging into the receptacle, make sure the
following points.
䡬
The power source voltage is stated on the
nameplate.
䡬
The cord is not damaged.
WARNING:
Do not charge at voltage higher than indicated on
the nameplate.
If charged at voltage higher than indicated on the
nameplate, the charger will burn out.
<UC18YRL, UC18YFL>
1. Insert the plug of battery charger into the
receptacle.
When the plug of battery charger has been inserted
into the receptacle, the charge status lamp will
blink in red. (At 1-second intervals)
WARNING
Do not use the electrical cord if
damaged. Have it repaired
immediately.
2. Insert the battery to the battery charger.
Insert the battery into the battery charger as shown
in Fig. 5. Make sure it contacts the bottom of the
battery charger.
Fig. 5
3. Charging
䡬
When the battery is connected to the battery
charger, charging will commence and the pilot
lamp will light in red. (See Table 2)
NOTE: If the pilot lamp flickers in red, pull out the plug
from the receptacle and check if the battery is
properly mounted.
䡬
When the battery is fully charged, the pilot lamp
will blink in red slowly. (At 1-second intervals) (See
Table 2)
Battery
Handle
Insert
Pull
out
Latch
Push
Battery
Charge status lamp
(red)
Overheat lamp
(green)
01Eng_C18DL_US 7/31/09, 16:1212
English
13
Before
charging
While
charging
Charging
complete
Charging
impossible
Overheat
standby
Malfunction in the
battery or the charger
Battery overheated.
Unable to charge
(Charging will commence
when battery cools).
Table 2
Indications of the pilot lamp
Blinks
(RED)
Lights
(RED)
Blinks
(RED)
Flickers
(RED)
Lights
(GREEN)
Lights for 0.5 seconds. Does not light
for 0.5 seconds. (off for 0.5 seconds)
Lights continuously
Lights for 0.5 seconds. Does not light
for 0.5 seconds. (off for 0.5 seconds)
Lights for 0.1 seconds. Does not light
for 0.1 seconds. (off for 0.1 seconds)
Lights continuously
Charge
status
lamp
(RED)
Overheat
lamp
(GREEN)
䡬
Regarding the temperature of the rechargeable
battery.
The temperatures for rechargeable batteries are
as shown in the Table 3, and batteries that have
become hot should be cooled for a while before
being recharged.
Table 3
Rechargeable Temperatures at which the
batteries battery can be recharged
EBM1830, BCL1815
32°F — 122°F (0°C — 50°C)
4. Disconnect battery charger from the receptacle.
CAUTION:
Do not pull the plug out of the receptacle by pulling
on the cord.
Make sure to grasp the plug when removing from
receptacle to avoid damaging cord.
5. Remove the battery from the battery charger.
Supporting the battery charger with hand, pull out
the battery from the battery charger.
<UC18YGL2>
1. Insert the plug of battery charger into the
receptacle.
When the plug of battery charger has been inserted
into the receptacle, pilot lamp will blink in red. (At
1-second intervals)
NOTE: When standby for cooling battery, UC18YRL cools the overheated battery by cooling fan.
WARNING
Do not use the electrical cord if
damaged. Have it repaired
immediately.
2. Insert the battery to the battery charger.
Insert the battery into the battery charger as shown
in Fig. 6. Make sure it contacts the bottom of the
battery charger.
Fig. 6
Pilot lamp
3. Charging
䡬
When the battery is connected to the battery
charger, charging will commence and the pilot
lamp will light in red. (See Table 4)
01Eng_C18DL_US 7/31/09, 16:1213
14
English
NOTE: If the pilot lamp flickers in red, pull out the plug
from the receptacle and check if the battery is
properly mounted.
䡬
When the battery is fully charged, the pilot lamp
will blink in red slowly. (At 1-second intervals) (See
Table 4)
Before
charging
While
charging
Charging
complete
Overheat
standby
Battery overheated.
Unable to charge.
(Charging will commence
when battery cools)
Table 4
Indications of the pilot lamp
Blinks
Lights
Blinks
Blinks
Lights for 0.5 seconds. Does not light
for 0.5 seconds. (off for 0.5 seconds)
Lights continuously
Lights for 0.5 seconds. Does not light
for 0.5 seconds. (off for 0.5 seconds)
Lights for 1 seconds. Does not light for
0.5 seconds. (off for 0.5 seconds)
Pilot lamp
(red)
䡬
Regarding the temperature of the rechargeable
battery.
The temperatures for rechargeable batteries are
as shown in Table 3, and batteries that have
become hot should be cooled for a while before
being recharged.
4. Disconnect battery charger from the receptacle.
CAUTION:
Do not pull the plug out of the receptacle by pulling
on the cord.
Make sure to grasp the plug when removing from
receptacle to avoid damaging cord.
5. Remove the battery from the battery charger.
Supporting the battery charger with hand, pull out
the battery from the battery charger.
Regarding electric discharge in case of new
batteries, etc.
䡬
As the internal chemical substance of new batteries
and batteries that have not been used for an
extended period is not activated, the electric
discharge might be low when using them the first
and second time. This is a temporary
phenomenon, and normal time required for
recharging will be restored by recharging the
batteries 2 – 3 times.
How to make the batteries perform longer.
䡬
Recharge the batteries before they become
completely exhausted.
When you feel that the power of the tool becomes
weaker, stop using the tool and recharge its
battery. If you continue to use the tool and exhaust
the electric current, the battery may be damaged
and its life will become shorter.
䡬
Avoid recharging at high temperatures.
A rechargeable battery will be hot immediately
after use. If such a battery is recharged immediately
after use, its internal chemical substance will
deteriorate, and the battery life will be shortened.
Leave the battery and recharge it after it has cooled
for a while.
CAUTION:
䢇
When the battery charger has been continuously
used, the battery charger will heated, thus
constituting the cause of the failures. Once the
charging has been completed, give 15 minutes rest
until the next charging.
䢇
If the battery is recharged when it is warm due to
battery use or exposure to sunlight, the pilot lamp
may light in green.
The battery will not be recharged. In such a case,
let the battery cool before charging. (UC18YRL,
UC18YFL)
䢇
When the pilot lamp flickers in red (at 0.2 second
intervals), check for and take out any foreign
objects in the charger’s battery installation hole.
If there are no foreign objects, it is probable that
the battery or charger is malfunctioning. Take it
to your authorized Service Center. (UC18YRL,
UC18YFL)
01Eng_C18DL_US 7/31/09, 16:1214
English
15
BEFORE USE
1. Check the work area environment
Check the work area to make sure that it is clear of
debris and clutter.
Clear the area of unnecessary personnel. Ensure
that lighting and ventilation is adequate.
2. Check if saw blade is tightened
While the saw blade is tightened securely for
immediate use when it is assembled at the factory,
be sure to check it out again for caution’s sake. A
bolt can be tightened when it is turned clockwise.
Use the provided box wrench to check it out.
For further details, refer to the item of [MOUNTING
AND DISMOUNTING THE SAW BLADE] on Page
18.
3. Check if wing nut is tightened
If the wing nut to adjust cutting depth (Fig. 8) is
loose, injury can result. Make sure that it is
tightened securely.
4. Check performance of lower guard
WARNING:
Make absolutely sure that the lower guard is not
fixed. Also, check and see if it can move smoothly.
If the saw blade is kept exposed, injury can result.
The lower guard (refer to Fig. 3) serves to protect
your body from coming into contact with the saw
blade. Make absolutely certain that the cover
smoothly performs to cover the saw blade. If the
lower guard should not move smoothly, never use
it without repairing it.
In such a case, get in touch with the store where
you bought the circular saw or the HITACHI
AUTHORIZED SERVICE CENTER for necessary
repair.
5. Check battery insertion
WARNING:
If the battery is inserted while the power switch
is in the ON position, the power tool will start
operating immediately, inviting serious accident.
CAUTION:
Until the battery locks in place with a little click, if
not, it may accidentally fall out of the tool causing
injury to you or someone around you.
6. Check for proper operation of the brake
This circular saw features an electric brake that
functions when the switch is released. Before using
the circular saw, ensure that the electric brake
functions properly. If it does not, bring the tool to
a HITACHI AUTHORIZED SERVICE CENTER.
7. Prepare a wooden work bench (Fig. 7)
Since the saw blade will extend beyond the lower
surface of the lumber, place the lumber on a work
bench when cutting. If a square block is utilized as
a work bench, select level ground to ensure it is
properly stabilized. An unstable work bench will
result in hazardous operation.
Fig. 7
CAUTION:
To avoid possible accident, always ensure that the
portion of lumber remaining after cutting is
securely anchored or held in position.
ADJUSTING THE SAW PRIOR TO USE
1. Adjusting the cutting depth (Fig. 8)
WARNING:
If the wing-nut is loose, injury can result. Tighten
it securely after adjustment.
To adjust cutting depth, loosen the Wing-nut and,
while holding the base with one hand, move the
main body up and down to obtain the prescribed
cutting depth.
After adjusting to the prescribed cutting depth,
tighten the Wing-nut securely.
Fig. 8
2. Adjusting the angle of inclination
WARNING:
If the wing-nut is loose, injury can result. Tighten
it securely after adjustment.
Wing-nut
Base
Base
Lumber
Work bench
Saw blade
01Eng_C18DL_US 7/31/09, 16:1215
16
English
As shown in Fig. 9 by loosening the wing-bolt on
the inclined gauge, the saw blade may be inclined
to a maximum angle of 50° in relation to the base.
Always insure that the wing-bolt is thoroughly
tightened after making the desired adjustment.
Fig. 9
NOTE:
Values of the inclined gauge provided on the base
merely serve as a rough guideline. For cutting
operation at an inclined posture, use the circular
saw after adjusting the angle between the base
and the saw blade with a protractor, etc.
3. Regulating the guide (Fig. 10)
The cutting position can be regulated by moving
the guide to the left or right after loosening its
knob-bolt. The guide may be mounted on either
the right or left side of the tool.
Fig. 10
OPERATION
WARNING:
䢇
Never touch the moving parts.
䢇
Never operate the circular saw with the saw blade
turned upward or to the side.
䢇
Do not fix and secure the switch lock. Besides,
keep your finger off the switch trigger when the
circular saw is being carried around. Otherwise,
the main body switch can be inadvertently turned
ON, resulting in unexpected accidents.
䢇
Keep the light ON during cutting operation only.
If it is lit ON in other cases, the main body switch
can be inadvertently turned ON, resulting in
unexpected accidents.
CAUTION:
䢇
Don’t remove circular saw from workpiece during
a cut while the saw blade is moving.
䢇
Pull out the battery after completing operation.
NOTE:
Take care not to lock the motor. If the motor is
locked, immediately turn the power off. If the motor
is locked for a while, the motor or battery may be
burnt.
1. Operation of switch (Switch trigger and light
switch) (Fig. 11)
For safe operation of the machine, a “switch lock”
is provided on the side of a handle.
If the “switch lock” is pulled in a state where it is
pressed in the direction of the arrow mark, the
main switch can be turned ON.
(1) Switch lock is used as the “light switch”. If the
“switch lock (light switch)” is pulled in a state, the
light is turned ON.
(2) After the switch is turned ON, even when you
release your hand from the switch lock, the body
continues running and the light continues being
turned ON as long as you keep on pulling the
switch trigger.
(3) If you release the switch trigger, you can turn OFF
the switch and the “switch lock” returns to the
original position automatically and the light turns
OFF too.
Fig. 11
2. Working performance per single charge (Reference
data)
䡬
Cutting capability differs according to the condition
of lumber, type of saw blade, ambient temperature,
battery characteristics, etc.
Inclined
gauge
Cutting line
(at 45 degrees)
Wing-bolt
Knob-bolt
Guide
Switch trigger
Switch lock
*(It works as
switch lock
alone if the
machine is
not
equipped
with light.)
01Eng_C18DL_US 7/31/09, 16:1216
English
17
Wood
Capacity
Battery (EBM1830) Battery (BCL1815)
2 × 8 (Spruce-Pine-Fir)
110 cuts 55 cuts
Concreteform plywood
133 ft (40 m) 67 ft (20 m)
(1/2” (12 mm) t)
To improve working efficiency per single charge,
䡬
Minimize operation (no-load operation) other than
cutting;
䡬
Avoid any unreasonably forced pressure to the
motor during cutting operation by twisting or
pressing the circular saw forcibly;
䡬
Avoid any use of dull saw blade.
3. Cutting procedures
CAUTION:
䢇
Recheck that the saw blade is securely clamped.
䢇
Confirm that the wing-nut for adjusting the slot
depth, the wing-bolt for adjusting the angle of
inclination.
(1) Place the base on the material, then align the
premarked line and the saw blade with the notch
at the front of the base (Fig. 12).
(2) When the base is not inclined, use the large notch
(Fig. 12, Fig. 13).
If the base is inclined (45 degrees), use the small
notch (Fig. 12, Fig. 14).
Fig. 12 <Top View>
Fig. 13 Not inclined
Fig. 14
NOTE:
When using the saw at the inclination of 45
degrees, use both the marks of on the bevel plate
and [45] on the inclined gauge of the base (Fig.
15).
What’s more, if it is absolutely essential to use the
saw at a precise angle, make adjustment using a
protractor, etc.
Fig. 15
Not inclined
Saw blade
Wing-bolt
Guide
Inclined
gauge
Wing-bolt
Cutting line
(at 45 degrees)
Bevel plate
Inclined
gauge
Wing-bolt
1 5
0
3 0
4 5
01Eng_C18DL_US 7/31/09, 16:1217
18
English
(3) Ensure that the switch is turned to the ON position
before the saw blade comes in contact with the
lumber. The switch is turned ON when the trigger
is squeezed; and OFF when the trigger is released.
Moving the saw straight at a constant speed will
produce optimum cutting.
CAUTION:
䢇
Before starting to saw, ensure that the saw blade
has reached full speed revolution.
䢇
Should the saw blade be stopped or made an
abnormal noise during operation, turn off the
switch immediately.
䢇
When finished with a job, pull out the battery from
the main body.
䢇
Twisting and forcibly pressing the saw during
cutting can result in unreasonable pressure on the
motor, so try to go straight quietly.
䢇
In the situation where the circular saw is
continuously operated while replacing the battery
with stocked spare batteries one after another, the
motor tends to overheat. Therefore, whenever the
housing becomes hot, give the saw a break for a
while.
䢇
Avoid cutting operation in a state where the base
bottom is afloat from the material being cut.
Otherwise, the motor can get locked.
MOUNTING AND DISMOUNTING THE
SAW BLADE
CAUTION:
To avoid serious accident, ensure the switch is in
the OFF position, and pull out the battery.
1. Dismounting the saw blade
(1) Set the cutting volume at maximum, and place the
Circular Saw as shown in Fig. 16.
Fig. 16
(2) Depress the lock lever, lock the spindle, and
remove the left-hand bolt and washer (B2) with
the box wrench.
(3) While holding the lower guard lever to keep the
lower guard fully retracted into the saw cover,
remove the saw blade (Fig. 17).
Fig. 17
2. Mounting the Saw Blade (Fig. 18)
WARNING:
If the left-hand bolt is worked using other tools
than the provided box wrench, excessive
tightening and insufficient tightening may take
place, resulting in injury.
䡬
Take procedures here that are contrary to the
detaching procedures.
Fig. 18
NOTE:
䡬
Thoroughly remove any sawdust which has
accumulated on the spindle, bolt and washers.
䡬
To assure proper rotation direction of the saw
blade, the arrow direction on the saw blade must
coincide with the arrow direction on the saw cover.
䡬
Using the fingers, tighten the left-hand bolt
retaining the saw blade as much as possible. Then
depress the lock lever, lock the spindle, and
thoroughly tighten the left-hand bolt.
CAUTION:
After mounting the saw blade, reconfirm that the
lock lever is firmly secured in the prescribed
position.
Box wrench
Lock lever
Tighten
Loosen
Lower guard lever
Saw cover
Left-hand bolt
Ring
Washer (A1)
Spindle
Washer (B2)
Concave
Saw blade
01Eng_C18DL_US 7/31/09, 16:1218
English
19
REPLACING LIGHT BULB
WARNING:
䢇
Make absolutely sure that the battery is removed
from the main body before replacing the light bulb.
䢇
Immediately after the light is turned OFF, the bulb
retains high temperature. Make sure to cool down
the light bulb thoroughly before replacing it so as
to prevent burns.
CAUTION:
When replacing the light bulb, check the shape of
base as well as the rating (12 V, 5 W), and then
carry out perfect mounting. Otherwise, the light
bulb can come off and/or cause overheat.
1. Detaching light bulb
(1) Remove the convex part of the light cover from
the concave part of the housing, and then pull out
the light cover in the arrow-marked direction as
shown in Fig. 19.
Fig. 19 <Side View>
(2) Push the back of the socket, and remove the socket
and the light bulb together from the housing (Fig.
20).
Fig. 20
(3) Remove the light bulb from the socket (Fig. 21).
Fig. 21 <Top View>
2. Attaching light bulb
Take procedures here that are contrary to the
detaching procedures.
NOTE:
䡬
When attaching the light bulb to the socket, insert
the light bulb until it lightly bumps against the
socket.
䡬
When attaching the socket to the housing, align
the socket with the hole of housing while watching
the back of the socket shown in Fig. 21, and insert
the socket until it lightly bumps against the
housing.
Housing
Light cover
Convex
Concave
Housing
Back of the socket
Housing
Light bulb
Socket
01Eng_C18DL_US 7/31/09, 16:1219
20
English
MAINTENANCE AND INSPECTION
CAUTION:
Pull out battery before doing any inspection or
maintenance.
1. Inspecting the saw blade
Since use of a dull saw blade will degrade
efficiency and cause possible motor malfunction,
sharpen or replace the saw blade as soon as
abrasion is noted.
CAUTION:
If a dull saw blade is used, reactive force is
increased during cutting operation. Avoid the use
of the dull saw blade without repair.
2. Check the mounting screws
Loose mounting screws are dangerous. Regularly
inspect them and make sure they are tight.
CAUTION:
Using this power tool with loosen, screws is
extremely dangerous.
3. Performance checkup and maintenance of lower
guard
Keep the lower guard in good shape for smooth
performance at all times. Be sure to make prompt
repair in case of any malfunction.
4. Adjusting the base and saw blade to maintain
perpendicularity
The angle between the base and the saw blade
has been adjusted to 90°, however should this
perpendicularity be lost for some reason, adjust
in the following manner.
(1) Turn the base face up (Fig. 22) and loosen the wing-
bolt.
Fig. 22
Square
Slotted
set screw
Wing-bolt
(2) Apply a square to the base and the saw blade and,
turning the slotted set screw with a slotted-head
screwdriver, shift the position of the base to
produce the desired right angle.
5. Check for dust
Dust may be removed with a clean rag or a cloth
dampened with soapy water.
Do not use bleach, chlorine, gasoline or thinner,
for they may damage the plastics.
6. Disposal of the exhausted battery
WARNING:
Do not dispose of the exhausted battery. The
battery must explode if it is incinerated. The
product that you have purchased contains a
rechargeable battery. The battery is recyclable. At
the end of it’s useful life, under various state and
local laws, it may be illegal to dispose of this
battery into the municipal waste stream. Check
with your local solid waste officials for details in
your area for recycling options or proper disposal.
7. Storage
Storing in a place below 104°F (40°C) and out of
the reach of children.
8. Service and repairs
All quality power tools will eventually require
servicing or replacement of parts because of wear
from normal use. To assure that only genuine
replacement parts must be used, all service and
repairs must be performed by a HITACHI
AUTHORIZED SERVICE CENTER, ONLY.
9. Service parts list
CAUTION:
Repair, modification and inspection of Hitachi
Power Tools must be carried out by a HITACHI
AUTHORIZED SERVICE CENTER.
This Parts List will be helpful if presented with the
tool to the HITACHI AUTHORIZED SERVICE
CENTER when requesting repair or other
maintenance. In the operation and maintenance
of power tools, the safety regulations and
standards prescribed in each country must be
observed.
MODIFICATIONS:
Hitachi Power Tools are constantly being improved
and modified to incorporate the latest
technological advancements.
Accordingly, some parts may be changed without
prior notice.
01Eng_C18DL_US 7/31/09, 16:1220
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
Hikoki C 18DL Manuel utilisateur
- Catégorie
- Outils électroportatifs
- Taper
- Manuel utilisateur
- Ce manuel convient également à
dans d''autres langues
- English: Hikoki C 18DL User manual
- español: Hikoki C 18DL Manual de usuario
Documents connexes
Autres documents
-
Hitachi C 18DL Safety Instructions And Instruction Manual
-
Hitachi C 18DGL Manuel utilisateur
-
-
Hitachi CR 18DL Manuel utilisateur
-
-
-
-
-
-