PROPOINT 8760894 Le manuel du propriétaire

Marque: PROPOINT

Modèle: 8760894

Taper: Le manuel du propriétaire

V1.0

Please read and understand all instructions before use. Retain this manual for future reference.

HYDRAULIC

BOTTLE JACK



8760894 12 Ton Hydraulic Welded Bottle Jack V1.0

2 For technical questions call 1-800-665-8685

SPECIFICATIONS

Type Welded

Lift Capacity

24,000 lb (10,886 kg)

Lift Range Total Range 9 to 18 in.

Ram Travel 9

Screw Extension

3-1/8 in.

Saddle Size 1-9/16 in. diameter

Base Size 5-1/4 x 4-5/8 in.

Construction

Steel

Operation Manual

HAZARD DEFINITIONS

Please familiarize yourself with the hazard notices found in this manual. A

notice is an alert that there is a possibility of property damage, injury or

death if certain instructions are not followed.

DANGER! This notice indicates an immediate and specific hazard that

will result in severe personal injury or death if the proper

precautions are not taken.

WARNING! This notice indicates a specific hazard or unsafe practice that

could result in severe personal injury or death if the proper

precautions are not taken.

CAUTION! This notice indicates a potentially hazardous situation that may

result in minor or moderate injury if proper practices are

not taken.

NOTICE! This notice indicates that a specific hazard or unsafe practice

will result in equipment or property damage, but not

personal injury.

V1.0 12 Ton Hydraulic Welded Bottle Jack 8760894

Visit www.princessauto.com for more information 3

INTRODUCTION

The 4 Ton Hydraulic Welded Bottle Jack is suitable for lifting loads up to

8,000 lb. The serrated saddle provides a secure grip against the load. An

automatic oil bypass prevents an overextension of the ram

during operation.

SAFETY

WARNING! Read and understand all instructions before using this

tool. The operator must follow basic precautions to reduce the risk

of personal injury and/or damage to the equipment.

Keep this manual for safety warnings, precautions, operating or inspection

and maintenance instructions.

WORK AREA

1. Operate in a safe work environment. Keep your work area clean, well-

lit and free of distractions. Place lights so you are not working in

a shadow.

2. Keep anyone not wearing the appropriate safety equipment away from

the work area.

3. Store tools properly in a safe and dry location. Keep tools out of the

reach of children.

PERSONAL SAFETY

WARNING! Wear personal protective equipment approved by the

Canadian Standards Association (CSA) or American National

Standards Institute (ANSI).

PERSONAL PROTECTIVE EQUIPMENT

1. Always wear impact safety goggles that provide front and side

protection for the eyes. Eye protection equipment should comply with

CSA Z94.3-07 or ANSI Z87.1 standards based on the type of

work performed.

2. Wear gloves that provide protection based on the work materials or to

reduce the effects of tool vibration.

3. Wear protective clothing designed for the work environment and tool.

4. Non-skid footwear is recommended to maintain footing and balance in

the work environment.

8760894 12 Ton Hydraulic Welded Bottle Jack V1.0

4 For technical questions call 1-800-665-8685

5. Wear steel toe footwear or steel toe caps to prevent a foot injury from

falling objects.

PERSONAL PRECAUTIONS

Control the tool, personal movement and the work environment to avoid

personal injury or damage to the tool.

1. Do not operate any tool when tired or under the influence of drugs,

alcohol or medications.

2. Avoid wearing clothes or jewelry that can become entangled with the

moving parts of a tool. Keep long hair covered or bound.

3. Do not overreach when operating the tool. Proper footing and balance

enables better control in unexpected situations.

SPECIFIC SAFETY PRECAUTIONS

WARNING! DO NOT let comfort or familiarity with product (gained

from repeated use) replace strict adherence to the tool safety rules.

If you use this tool unsafely or incorrectly, you can suffer serious

personal injury.

1. Use the correct tool for the job. This tool was designed for a specific

function. Do not modify or alter this tool or use it for an

unintended purpose.

2. Do not use the tool if any parts are damaged, broken or misplaced.

Repair or replace the parts.

3. Do not overload the jack beyond its rated load capacity

(see Specifications).

4. Do not use a handle extension for the jack handle.

5. Rest the jack’s base on a firm, level surface capable of sustaining the

load. Keep the surface clean and free from debris.

6. Make sure the saddle is fully positioned under the load

before operating.

7. Make sure the load is stable, so it does not shift when lifting

or lowering.

8. Make sure there is enough clearance around the jack and the load

during lifting or lowering actions.

V1.0 12 Ton Hydraulic Welded Bottle Jack 8760894

Visit www.princessauto.com for more information 5

9. Before lifting a vehicle, apply the emergency brake and block

all wheels.

10. Support the load with jack stands or a support structure of adequate

capacity immediately after lifting. Never work under a load without

additional support devices.

11. The jack must remain in a static position for lifting and lowering loads.

Never move a load that is elevated on the jack. Ensure the load

remains stable at all times.

12. Do not push a load off the jack; lower carefully.

13. Before lowering load, ensure that there are no obstructions underneath

and that all people are standing clear.

14. Do not place your hands between the moving components.

15. Never allow load to tilt on the jack as the jack may kick out causing

injury to the operator and/or cause the load to fall.

16. DO NOT use the jack if damaged or it was subjected to a dynamic

shock load. This is a sudden and unexpected load or force applied to

the jack. Have the jack inspected and repaired by a qualified

service technician.

HYDRAULIC PRECAUTIONS

DANGER! Seek immediate medical attention if hydraulic fluid under

pressure penetrates your skin. See Injection Injury precautions for

instructions before using a pressurized hydraulic system.

1. Do not touch or handle hydraulic hoses or components while under

pressure. Hydraulic fluid escaping under pressure has sufficient force to

penetrate your clothing and skin. A pinpoint hole may inject hydraulic fluid

into your body. Seek immediate medical attention if this occurs (see

Injection Injury).

2. Do not adjust the hydraulic system’s relief setting. The settings are

preset by the factory.

3. Hydraulic oil under pressure is hot and can cause a burn injury if

touched, sprayed or spilled. Allow the hydraulic system to cool before

conducting maintenance.

8760894 12 Ton Hydraulic Welded Bottle Jack V1.0

6 For technical questions call 1-800-665-8685

4. Hydraulic components require regular inspection. Release all pressure

from the system before you inspect it. Replace damaged hydraulic

parts with identical manufacturer's components.

5. Do not attempt makeshift repairs to a hydraulic system. Such repairs can

fail suddenly and create a hazardous condition.

6. Hydraulic fluid has a combustible flash point of 200°F (93°F). Do not

expose the fluid to an ignition source.

7. Change your clothing immediately if sprayed with hydraulic fluid. Store

clothing or rags contaminated with hydraulic fluid in an approved

metal safety can with a spring-closing lid and venting designed to

contain a fire.

8. Only use hydraulic fluid in the pump. Do not substitute or mix brake

fluid, or any other fluid, with the hydraulic fluid. This can result in a

pump failure and injure the user or bystander. It may also damage

the pump.

INJECTION INJURY

DANGER! Seek immediate, professional medical treatment if fluid

penetrates your skin. It may feel like a pricking or sting. Do not wait

for the appearance of symptoms. A toxic reaction can occur from

the exposure. Delay in treatment can lead to amputation or death.

Inform the medical staff that you have a fluid penetration injury as soon as you

arrive at the medical facility. The severity of the symptoms will depend on the type

of fluid injected. Bring the Safety Data Sheet for the fluid with you to the medical

facility if possible.

INJECTION PRECAUTIONS

Fluid can penetrate the skin at 100 PSI pressure. Fluid escaping under

pressure from the tool has sufficient force to penetrate your clothing and

skin. Follow the precautions below to avoid an injection injury.

1. Always check for leaks wearing a face shield, safety goggles,

rubberized gloves and protective clothes.

2. Release all pressure from the system before you inspect it.

3. Do not use your hands to detect a fluid leak. Use a large piece of wood,

cardboard or paper and watch for discolouration.

V1.0 12 Ton Hydraulic Welded Bottle Jack 8760894

Visit www.princessauto.com for more information 7

4. Replace damaged parts with identical manufacturer's components to

ensure it is rated to handle the pressure.

UNPACKING

WARNING! Do not operate the tool if any part is missing. Replace

the missing part before operating. Failure to do so could result in a

malfunction and personal injury.

Remove the parts and accessories from the packaging and inspect for damage.

Make sure that all items in the contents are included.

Contents:

• Bottle Jack

• 2 Piece Handle

IDENTIFICATION KEY

A Ram E Saddle

B Oil Plug F Extension Screw

C Release Valve G Handle Sleeve

D Handle Assembly

OPERATION

Letter references in parenthesis (A) refer to the included Identification Key.

RAISING A LOAD

WARNING! Do not place any part of your body under the load

without jack stands in place. The bottle jack is not designed to

maintain heavy loads for long periods of time

1. Place the jack on a hard level surface capable of handling the load.

2. Assemble the handle. The spring clips must align with the slots.

3. Close the release valve (C). Insert the end of the handle (D) over the

valve and twist to the right.

4. Insert the handle into the handle sleeve (G).

5. Pump to raise the ram. Stop just before the ram contacts the load’s lift

point. Inspect the ram’s position and adjust if necessary.

6. Pump slowly until the ram is supporting the load. Continue to pump as

normal to lift the load to the desired height.

Fig. 1

8760894 12 Ton Hydraulic Welded Bottle Jack V1.0

8 For technical questions call 1-800-665-8685

7. Position supports like jack stands if the load will remain off the ground

for an extended period. Consult the manual for the support device for

proper placement.

LOWERING A LOAD

WARNING! Dynamic shock loads are created by quick opening and

closing of the release valve when lowering the load. The resulting

overload may cause the hydraulic system to fail, which could result

in severe personal injury and/or property damage.

WARNING! Before lowering the load or vehicle, ensure that there are

no obstructions underneath and that all people are standing clear.

1. Insert the handle end over the release valve.

2. Open the valve by gradually twisting to the left.

3. The load will begin to lower as air escapes through the valve.

4. Twist right to slow and left to increase the rate of descent.

5. Remove the jack once the load is on the ground or on a support

mechanism like jack stands.

6. The ram should fully retract. If it does not, push down on it until it

is seated.

RAISING AND LOWERING A VEHICLE

Take these additional steps before following instructions in Raising a Load

and Lowering a Load.

1. Set the vehicle in parking gear and engage the parking brake.

1.1 For vehicles with a manual transmission, engage the parking brake

and leave the car in reverse or 1st gear. Consult your vehicle owner’s

manual for the correct gear.

2. Place wheel chocks that fit the wheel curve on either side of the

vehicle’s remaining wheels.

3. Place the jack only on support points or areas specified by the vehicle

manufacturer (consult owner’s manual).

4. Lift the vehicle to a height that leaves enough room to place the

jack stands.

5. When the work is done, raise the load enough with the jack to

carefully remove the jack stands.

V1.0 12 Ton Hydraulic Welded Bottle Jack 8760894

Visit www.princessauto.com for more information 9

6. Slowly and carefully lower the load.

CARE & MAINTENANCE

1. Maintain the tool with care. A tool in good condition is efficient, easier

to control and will have fewer problems.

2. Inspect the tool components periodically. Repair or replace damaged

or worn components. Only use identical replacement parts

when servicing.

3. Follow instructions for lubricating and changing accessories.

4. Keep the tool handles clean, dry and free from oil/grease at all times.

5. Maintain the tool’s labels and name plates. These carry important

information. If unreadable or missing, contact Princess Auto Ltd.

for replacements.

6. Have a qualified technician inspect the jack:

6.1 Once a year.

6.2 After receiving a shock load. Take the jack out of service until the

technician certifies that it is safe to use.

WARNING! Only qualified service personnel should repair the tool.

An improperly repaired tool may present a hazard to the user

and/or others.

HYDRAULIC RAM MAINTENANCE

Monthly maintenance is recommended for the hydraulic ram. Any restrictions

due to dirt, rust, etc. can cause the either slow movement or extremely rapid

jerks, damaging the internal components. The following steps are designed to

keep the pump maintained and operational.

1. Lubricate the cylinder and the pumping mechanism with light oil.

2. Visually inspect for cracked welds, bent, loose, missing parts or hydraulic

oil leaks.

3. Check and maintain the ram oil level.

4. Always store the hydraulic ram in the fully retracted position. This will help

protect critical areas from corrosion.

8760894 12 Ton Hydraulic Welded Bottle Jack V1.0

10 For technical questions call 1-800-665-8685

5. Do not use brake or transmission fluids or regular motor oil, as they

can damage the seals. Always purchase and use products labeled

hydraulic jack oil.

6. Remove any hydraulic pump from service that is damaged, worn down or

operates abnormally, until repaired by an authorized service technician.

REPLACING THE HYDRAULIC JACK OIL

Replace the jack oil annually.

1. Lower the ram and remove the oil plug (Fig. 2).

2. Lay the jack on its side and drain the oil into a suitable container (Fig.

3). Dispose of used hydraulic oil in accordance with local by-laws.

3. Stand the jack on its base and wipe off any excess oil.

4. Fill the cylinder with a high quality hydraulic jack oil, up to the oil plug

opening (Fig. 4).

5. Follow the steps in Bleeding the Hydraulic System.

BLEEDING THE HYDRAULIC SYSTEM

Bleed excess air from the hydraulic system as follows:

1. Open the release valve by turning it counterclockwise.

2. Remove the oil plug (B) and fill the pump with hydraulic fluid.

3. Wait 5 minutes for trapped air to rise to the surface.

4. Pump the handle for several full strokes to eliminate any air in the system.

5. Check the oil filler hole and if necessary, top off with more hydraulic oil.

6. Restore the oil filler screw. Close the release valve by

turning clockwise.

Fig. 2

Fig. 3

Fig. 4

V1.0 12 Ton Hydraulic Welded Bottle Jack 8760894

Visit www.princessauto.com for more information 11

7. Test the ram several times for proper operation before putting it into use.

Do not use the ram if it still does not appear to be working properly. Have

a qualified technician repair the hydraulic system.

FLUSHING THE VALVE

Contaminants may block the release valve, causing issues when

attempting to lower a load. Clear the valve with the following steps.

1. Lower the saddle and securely close the release valve.

2. Manually lift the saddle several inches.

3. Open the release valve and force the saddle down as quickly as possible.

CLEANING

Clean the tool with a clean rag and a degreasing solvent. Lubricate

moving contact points after cleaning to ensure binding does not occur.

LUBRICATION

Inspect and lubricate the tool when required. Only use light oil to lubricate

the tool. Other lubricants may not be suitable and could damage the tool

or cause a malfunction during use.

STORAGE

Lower the ram to its lowest position. Apply a thin coat of lubricant to the

steel parts to avoid rust. Remove the lubricant before using the tool again.

DISPOSAL

Recycle a tool damaged beyond repair at the appropriate facilit y.

Contact your local municipality for a list of disposal facilities or by-laws for

electronic devices, batteries, oil or other toxic liquids.

IMPORTANT! DO NOT pollute the environment by allowing

uncontrolled discharge of waste oil.

HYDRAULIC FLUID

Do not drain hydraulic oil into the sewer system or dispose in an

uncontrolled location. Hydraulic fluid may take more than a year to

breakdown in the environment and the ingredients may still be toxic.

Contact your local municipality for proper disposal instructions or locations.

8760894 12 Ton Hydraulic Welded Bottle Jack V1.0

12 For technical questions call 1-800-665-8685

TROUBLESHOOTING

Visit a Princess Auto Ltd. location for a solution if the tool does not function

properly or parts are missing. If unable to do so, have a qualified

technician service the tool.

PROBLEM(S) POSSIBLE CAUSE(S) SUGGESTED SOLUTION(S)

Jack will not lift

load.

1. The release valve is not

closed tightly.

2. Overloaded the jack.

3. Air supply is inadequate.

4. Air is trapped in the

hydraulic system.

1. Close the release valve firmly.

2. Reduce load or use a jack with

a greater lift capacity.

3. Ensure adequate air supply.

4. Bleed air from the system.

Jack will lift, but

will not maintain

pressure.

1. Release valve is not

closed tightly.

2. Overloaded the jack.

3. Hydraulic unit is

malfunctioning.

1. Close the release valve firmly.

2. Reduce load or use a jack with

a greater lift capacity.

3. a. Replace the seals.

b. Have service technician repair

the jack.

Will not lower

after loading.

1. Reservoir is overfilled.

2. Linkages are binding.

3. Contaminated release

valve.

1. Drain oil to the proper level.

2. Clean and lubricate all moving

parts.

3. See Care & Maintenance -

Flushing the Valve

Poor lift

performance.

1. Hydraulic oil level is low.

2. Air is trapped in the

hydraulic system.

1. Add oil to the proper level.

2. Bleed air from the system.

Will not lift to the

max. hei ght.

1. Air is trapped in the

system.

2. Hydraulic oil level is too

low.

1. Bleed air from the system.

2. Add oil to the proper level.

V1.0 12 Ton Hydraulic Welded Bottle Jack 8760894

Visit www.princessauto.com for more information 13

PARTS BREAKDOWN

8760894 12 Ton Hydraulic Welded Bottle Jack V1.0

14 For technical questions call 1-800-665-8685

PARTS LIST

# DESCRIPTION QTY

1 Round Wire Snap Ring 1

2 Rectangular Ring 2

O-ring

4 Piston Rod Assembly 1

5 Bowl Washer 1

O-ring

Round Wire Snap Ring

8 Base Welding Parts 1

9 Oil Plug 1

Steel Ball 6mm

Release Valve Assembly

Plastic Plug 1

13 Adjusting Screw Assembly 1

Spring

15 Spring Holder 1

16 Steel Ball 3mm 1

17 Steel Ball 5mm 2

Bowl Washer

19 Pump Plunger Assembly 1

20 Pin 2

21 Handle Socket Assembly 1

Cutter Pin

23 Handle Assembly 1

24 Seal Kit 1

V1,0 8760894

Vous devez lire et comprendre toutes les instructions avant d'utiliser l'appareil. Conservez ce

manuel afin de pouvoir le consulter plus tard.

CRIC-BOUTEILLE

HYDRAULIQUE



8760894 Cric-bouteille hydraulique soudé, 12 tonnes V1,0

2 En cas de questions techniques, appelez le 1-800-665-8685

SPÉCIFICATIONS

Type

Soudé

Capacité de levage 10 886 kg (24 000 lb)

Plage de levage Échelle totale 9 à 18 po

Course du vérin

9 po

Rallonge de vis 3 1/8 po

Taille de selle

Diamètre de 1 9/16 po

Dimensions de la base

5 1/4 x 4 5/8 po

Construction

Acier

Utilisation

Manuel

DÉFINITIONS DE DANGER

Veuillez-vous familiariser avec les avis de danger qui sont présentés dans

ce manuel. Un avis est une alerte indiquant qu'il existe un risque de

dommage à la propriété, de blessure ou de décès si on ne respecte pas

certaines instructions.

DANGER ! Cet avis indique un risque immédiat et particulier qui

entraînera des blessures corporelles graves ou

même la mort si on omet de prendre les

précautions nécessaires.

AVERTISSEMENT ! Cet avis indique un risque particulier ou une pratique

non sécuritaire qui pourrait entraîner des blessures

corporelles graves ou même la mort si on omet de

prendre les précautions nécessaires.

ATTENTION ! Cet avis indique une situation possiblement

dangereuse qui peut entraîner des blessures

mineures ou modérées si on ne procède pas de la

façon recommandée.

AVIS ! Cet avis indique un risque particulier ou une pratique

non sécuritaire qui entraînera des dommages au

niveau de l'équipement ou des biens, mais non des

blessures corporelles.

V1,0 Cric-bouteille hydraulique soudé, 12 tonnes 8760894

Visitez www.princessauto.com pour plus d'i nformations 3

INTRODUCTION

Le cric-bouteille hydraulique de 4 tonnes convient pour lever des

charges allant jusqu’à 8 000 lb. La douille crénelée procure une prise

solide sur la charge. Une dérivation automatique de l’huile empêche un

allongement excessif du vérin durant le fonctionnement.

SÉCURITÉ

AVERTISSEMENT ! Veuillez lire et comprendre toutes les

instructions avant d'utiliser cet outil. L'utilisateur doit respecter

les précautions de base lorsqu'il utilise cet outil afin de réduire

le risque de blessure ou de dommage à l'équipement.

Conservez ce manuel qui contient les avertissements de sécurité, les

précautions, les instructions de fonctionnement ou d'inspection

et d'entretien.

AIRE DE TRAVAIL

1. Travaillez dans un environnement de travail sécuritaire. Gardez

votre aire de travail propre, bien éclairée et exempte de toute

distraction. Placez les lampes de façon à ne pas travailler dans

l’ombre.

2. Assurez-vous que les personnes qui ne portent pas l'équipement

de sécurité approprié ne se trouvent pas à proximité de l'aire de

travail.

3. Rangez les outils correctement dans un lieu sécurisé et sec.

Gardez les outils hors de la portée des enfants.

SÉCURITÉ PERSONNELLE

AVERTISSEMENT ! Portez de l'équipement de protection

personnelle homologué par l'Association canadienne de

normalisation (CSA) ou l'American National Standards Institute

(ANSI).

ÉQUIPEMENT DE PROTECTION PERSONNELLE

1. Portez toujours des lunettes antiprojections qui offrent une protection

frontale et latérale pour les yeux. L'équipement de protection des yeux

devrait être conforme à la norme CSA Z94.3-07 ou ANSI Z87.1

8760894 Cric-bouteille hydraulique soudé, 12 tonnes V1,0

4 En cas de questions techniques, appelez le 1-800-665-8685

fonction du type de travail effectué.

2. Portez des gants qui protègent en fonction des matériaux de travail

et pour réduire les effets des vibrations de l'outil.

3. Portez des vêtements de protection conçus pour l'environnement

de travail et pour l'outil.

4. Les chaussures antidérapantes sont recommandées pour maintenir

la stabilité et l'équilibre au sein de l'environnement de travail.

5. Portez des chaussures à embout d'acier ou à coquilles d'acier pour

éviter les blessures aux pieds dues à la chute d'objets.

PRÉCAUTIONS PERSONNELLES

Gardez le contrôle de l'outil, de vos mouvements et de l'environnement

de travail pour éviter les blessures ou le bris de l'outil.

1. N'utilisez pas l'outil si vous êtes fatigué ou sous l'effet de drogues,

d'alcool ou de médicaments.

2. Évitez de porter des vêtements ou des bijoux pouvant se prendre

dans les pièces mobiles d'un outil. Gardez les cheveux longs

recouverts ou attachés.

3. N'utilisez pas l'outil si vous devez étirer les bras pour vous en

servir. Une stabilité et un équilibre appropriés sont nécessaires afin

d'avoir un meilleur contrôle en cas de situations inattendues.

CONSIGNES DE SÉCURITÉ

SPÉCIFIQUES

AVERTISSEMENT ! Ne permettez PAS au confort ou à votre

familiarisation avec l'outil (obtenus après un emploi répété) de se

substituer à une adhésion stricte aux règles de sécurité de l'outil.

Si vous utilisez cet outil de façon dangereuse ou incorrecte, vous

pouvez subir des blessures corporelles graves.

1. Utilisez le bon outil pour la tâche à effectuer. Cet outil a été conçu

pour une utilisation spécifique. Évitez de modifier ou d'altérer cet

outil ou de l'utiliser à une fin autre que celle pour laquelle il a été

conçu.

2. N’utilisez pas l’outil si des pièces présentent des dommages ou sont

V1,0 Cric-bouteille hydraulique soudé, 12 tonnes 8760894

Visitez www.princessauto.com pour plus d'i nformations 5

déplacées. Réparez ou remplacez les pièces.

3. Ne surchargez pas les chandelles au-delà de leur capacité de charge

nominale (consultez Spécifications).

4. N’utilisez pas de rallonge sur la poignée du cric.

5. Déposez la base du cric sur une surface solide et de niveau pouvant

soutenir la charge. Gardez la surface propre et exempte de débris.

6. Assurez-vous que la douille est correctement placée sous la charge

avant de mettre en marche.

7. Assurez-vous que la charge est stable pour éviter qu’elle se déplace

durant le levage ou la descente.

8. Assurez-vous qu’il existe un espace suffisant autour du cric et de la

charge durant le levage ou la descente.

9. Avant de soulever un véhicule, appliquez le frein d'urgence et bloquez

toutes les roues.

10. Appuyez la charge sur des chandelles ou sur une structure d’appui de

capacité suffisante immédiatement après l’aconsultez soulevée. Ne

travaillez jamais sous une charge sans appareils d’appui additionnels.

11. Le cric doit rester en position immobile afin de pouconsultez soulever

et abaisser des charges. Ne déplacez jamais une charge soulevée sur

un cric. Assurez-vous que la charge demeure stable en tout temps.

12. Ne poussez pas la charge hors du cric; abaissez-la doucement.

13. Avant d'abaisser la charge, assurez-vous qu'aucune obstruction ne

se trouve en dessous et que tous les gens se trouvent à l'écart.

14. Ne placez pas vos mains entre les composants mobiles.

15. Ne laissez jamais la charge s’incliner sur le cric car le cric pourrait

céder et causer des blessures à l’opérateur et/ou causer la chute

de la charge.

16. N’utilisez PAS le cric s’il est endommagé ou s’il a subi un choc

dynamique. Il s’agit là d’une charge ou d’une force soudaine et

inattendue qui est appliquée au niveau du cric. Faites vérifier et réparer

le cric par un technicien de service compétent.

8760894 Cric-bouteille hydraulique soudé, 12 tonnes V1,0

6 En cas de questions techniques, appelez le 1-800-665-8685

SÉCURITÉ HYDRAULIQUE

DANGER ! Contactez immédiatement un médecin si le liquide

hydraulique sous pression vous pénètre la peau. Consultez la

rubrique Instructions en cas de blessures par injection pour

connaître la marche à suivre avant d’utiliser un système

hydraulique sous pression.

1. Ne touchez pas et ne manipulez pas les tuyaux hydrauliques ou les

composants sous pression. Une fuite de liquide hydraulique sous

pression peut avoir une force suffisante pour pénétrer la peau. Un trou

d'aiguille peut projeter du liquide hydraulique dans votre corps. Appelez

immédiatement un médecin dans un tel cas (voir Blessure Par

Injection).

2. Ne réglez pas les ajustements de détente du système hydraulique. Les

réglages sont effectués au préalable en usine.

3. L’huile hydraulique sous pression est chaude et peut causer des

blessures par brûlure en cas de contact, de pulvérisation ou de

déversement. Laissez le système hydraulique refroidir avant de

procéder à l’entretien.

4. Les composants hydrauliques doivent faire l'objet d'une inspection

régulière. Libérez toute la pression du système avant de procéder à

son inspection. Remplacez les pièces hydrauliques endommagées

par des composants provenant du même fabricant.

5. N'essayez pas de faire des réparations de fortune à un système

hydraulique. De telles réparations peuvent être sujettes à des

défaillances soudaines et causer une condition dangereuse.

6. Le liquide hydraulique présente un point d'inflammabilité de

93 °C (200 °F). N'exposez le liquide à aucune source d'allumage.

7. Changez immédiatement vos vêtements s'ils ont été arrosés avec

le liquide hydraulique. Rangez les vêtements ou les chiffons

contaminés par le liquide hydraulique dans une boîte de sécurité

en métal approuvée munie d'un couvercle à ressort et d'un

dispositif de mise à l'air libre capable de contenir un incendie.

8. Utilisez uniquement du liquide hydraulique dans la pompe. Ne

remplacez pas ou ne mélangez pas le liquide ou tout autre liquide

avec le liquide hydraulique. Il pourrait en résulter le bris de la

pompe et des blessures pour l’utilisateur et les gens à proximité.

La page est en cours de chargement...

PROPOINT 8760894 Le manuel du propriétaire

Marque: PROPOINT

Modèle: 8760894

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: PROPOINT 8760894 Owner's manual

PROPOINT 8760894 Le manuel du propriétaire

PROPOINT 8760894 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents