Losi LOS03022T1 Le manuel du propriétaire

Marque: Losi

Modèle: LOS03022T1

Catégorie: Jouets

Taper: Le manuel du propriétaire

Ce manuel convient également à

Before operating this vehicle, please read all printed materials thoroughly.

Horizon Hobby is not responsible for inadvertent errors in this manual.

INSTRUCTION MANUAL

BEDIENUNGSANLEITUNG

MANUEL D’UTILISATION

MANUALE DI ISTRUZIONI

Battery and Charger

Not Included

22S SCT RTR: 1:10 2WD SHORT COURSE TRUCK • INSTRUCTION MANUAL

WARNING: Read the ENTIRE instruction manual to become familiar with the features of the product before operating. Failure to operate the product correctly can result in damage

to the product, personal property and cause serious injury.

This is a sophisticated hobby product. It must be operated with caution and common sense and requires some basic mechanical ability. Failure to operate this Product in a safe and respon-

sible manner could result in injury or damage to the product or other property. This product is not intended for use by children without direct adult supervision. Do not use with incompat-

ible components or alter this product in any way outside of the instructions provided by Horizon Hobby, LLC. This manual contains instructions for safety, operation and maintenance. It is

essential to read and follow all the instructions and warnings in the manual, prior to assembly, setup or use, in order to operate correctly and avoid damage or serious injury.

NOTICE

All instructions, warranties and other collateral documents are subject to change at the sole discretion of Horizon Hobby, LLC.

For up-to-date product literature, visit horizonhobby.com and click on the support tab for this product.

MEANING OF SPECIAL LANGUAGE

The following terms are used throughout the product literature to indicate various levels of potential harm when operating this product:

WARNING: Procedures, which if not properly followed, create the probability of property damage, collateral damage, and serious injury OR create a high probability of superﬁ cial injury.

CAUTION: Procedures, which if not properly followed, create the probability of physical property damage AND a possibility of serious injury.

NOTICE: Procedures, which if not properly followed, create a possibility of physical property damage AND a little or no possibility of injury.

Age Recommendation: Not for children under 14 years. This is not a toy.

updates and more. Click on the Support tab at WWW.LOSI.COM and follow the product

registration link to stay connected.

As the user of this product, you are solely responsible for operating in a manner that does not

endanger yourself and others or result in damage to the product or property of others.

This model is controlled by a radio signal subject to interference from many sources outside

your control. This interference can cause momentary loss of control, so it is advisable to

always keep a safe distance in all directions around your model as this margin will help avoid

collisions or injury.

• Never operate your model with low transmitter batteries.

• Always operate your model in open spaces away from full-size vehicles, trafﬁ c and people.

• Never operate the model in the street or in populated areas for any reason.

• Carefully follow the directions and warnings for this and any optional support equipment

(chargers, rechargeable battery packs, etc.) you use.

• Keep all chemicals, small parts and anything electrical out of the reach of children.

• Never lick or place any portion of the model in your mouth as it could cause serious injury

or even death.

• Exercise caution when using tools and sharp instruments.

• Take care during maintenance as some parts may have sharp edges.

• Immediately after using your model, do NOT touch equipment such as the motor, electronic

speed control and battery, because they generate high temperatures. You may burn

yourself seriously touching them.

• Do not put ﬁ ngers or any objects inside rotating and moving parts, as this may cause

damage or serious injury.

• Always turn on your transmitter before you turn on the receiver in the car. Always turn off

the receiver before turning your transmitter off.

• Keep the wheels of the model off the ground when checking the operation of the radio

equipment.

SAFETY PRECAUTIONS AND WARNINGS

TABLE OF CONTENTS

BOX CONTENTS ........................................................................................................3

COMPONENTS ..................................................................................................................3

WATER-RESISTANT VEHICLE WITH WATERPROOF ELECTRONICS ..............................3

GENERAL PRECAUTIONS ...................................................................................................3

WET CONDITIONS MAINTENANCE ....................................................................................3

QUICK START ............................................................................................................3

CHARGING THE BATTERY .........................................................................................3

INSTALLING THE BATTERY ........................................................................................4

SPEKTRUM STX2 RADIO SYSTEM .............................................................................4

INSTALLING THE TRANSMITTER BATTERIES ........................................................................4

SRX200 RECEIVER ....................................................................................................4

DRIVING PRECAUTIONS ..........................................................................................5

POWERING ON THE VEHICLE ....................................................................................5

BEFORE RUNNING YOUR VEHICLE ............................................................................5

RUN TIME .................................................................................................................6

TO IMPROVE RUN TIMES ...................................................................................................6

PERFORMING A CONTROL DIRECTION TEST.............................................................6

CHANGING THE TRAVEL ADJUST SETTINGS .............................................................6

DYNAMITE® WP 60A FWD/REV BRUSHED ESC (DYNS2210) ....................................6

SPECIFICATIONS ...............................................................................................................6

ESC LED STATUS ...............................................................................................................6

MOTOR TO ESC CONNECTION ...........................................................................................6

ESC CALIBRATION PROCEDURE ........................................................................................6

ESC FUNCTIONS AND MODES ...........................................................................................6

ESC PROGRAMMING PROCEDURE ....................................................................................7

DESCRIPTIONS ..................................................................................................................7

DYNAMITE

12-TURN 550 BRUSHED MOTOR (DYNS1222).......................................8

PRECAUTIONS ..................................................................................................................8

GEARING .........................................................................................................................8

CHANGING THE PINION GEAR/GEAR RATIO ......................................................................8

SETTING THE GEAR MESH .................................................................................................8

TROUBLESHOOTING GUIDE ......................................................................................8

LIMITED WARRANTY ...........................................................................................8–9

WARRANTY AND SERVICE CONTACT INFORMATION ................................................9

FCC STATEMENT .......................................................................................................9

IC INFORMATION .....................................................................................................9

COMPLIANCE INFORMATION FOR THE EUROPEAN UNION ......................................9

REPLACEMENT PARTS ............................................................................................35

RECOMMENDED PARTS..........................................................................................35

OPTIONAL PARTS ...................................................................................................35

EXPLODED VIEW ..............................................................................................36–39

22S SCT RTR: 1:10 2WD SHORT COURSE TRUCK • INSTRUCTION MANUAL

2.4GHZ DIGITAL

RADIO SYSTEM

BOX CONTENTS

Your new Horizon Hobby vehicle has been designed and built with a combination of

waterproof and water-resistant components to allow you to operate the product in many

“wet conditions,” including puddles, creeks, wet grass, snow and even rain.

While the entire vehicle is highly water-resistant, it is not completely waterproof and your

vehicle should NOT be treated like a submarine. The various electronic components used in

the vehicle, such as the Electronic Speed Control (ESC), servo(s) and receiver are waterproof,

however, most of the mechanical components are water-resistant and should not be

submerged.

Metal parts, including the bearings, hinge pins, screws and nuts, as well as the contacts

in the electrical cables, will be susceptible to corrosion if additional maintenance is not

performed after running in wet conditions. To maximize the long-term performance of your

vehicle and to keep the warranty intact, the procedures described in the “Wet Conditions

Maintenance” section below must be performed regularly if you choose to run in wet

conditions. If you are not willing to perform the additional care and maintenance

required, then you should not operate the vehicle in those conditions.

CAUTION: Failure to exercise caution while using this product and

complying with the following precautions could result in product malfunction

and/or void the warranty.

GENERAL PRECAUTIONS

• Read through the wet conditions maintenance procedures and make sure that you

have all the tools you will need to properly maintain your vehicle.

• Not all batteries can be used in wet conditions. Consult the battery manufacturer before

use. Caution should be taken when using Li-Po batteries in wet conditions.

• Most transmitters are not water-resistant. Consult your transmitter’s manual or the

manufacturer before operation.

• Never operate your transmitter or vehicle where lightning may be present.

• Do not operate your vehicle where it could come in contact with salt water (ocean

water or water on salt-covered roads), contaminated or polluted water. Salt water

is very conductive and highly corrosive, so use caution.

• Even minimal water contact can reduce the life of your motor if it has not been certiﬁ ed

as water-resistant or waterproof. If the motor becomes excessively wet, apply very light

throttle until the water is mostly removed from the motor. Running a wet motor at high

speeds may rapidly damage the motor.

• Driving in wet conditions can reduce the life of the motor. The additional resistance of

operating in water causes excess strain. Alter the gear ratio by using a smaller pinion or larger

spur gear. This will increase torque (and motor life) when running in mud, deeper puddles, or

any wet conditions that will increase the load on the motor for an extended period of time.

WET CONDITIONS MAINTENANCE

• Drain any water that has collected in the tires by spinning them at high speed. With the

body removed, place the vehicle upside down and pull full throttle for a few short bursts

until the water has been removed.

CAUTION: Always keep hands, ﬁ ngers, tools and any loose or hanging

objects away from rotating parts when performing the above drying

technique.

• Remove the battery pack(s) and dry the contacts. If you have an air compressor or a can of

compressed air, blow out any water that may be inside the recessed connector housing.

• Remove the tires/wheels from the vehicle and gently rinse the mud and dirt off with a

garden hose. Avoid rinsing the bearings and transmission.

NOTICE: Never use a pressure washer to clean your vehicle.

• Use an air compressor or a can of compressed air to dry the vehicle and help remove any

water that may have gotten into small crevices or corners.

• Spray the bearings, drive train, fasteners and other metal parts with a water-displacing

light oil. Do not spray the motor.

• Let the vehicle air dry before you store it. Water (and oil) may continue to drip for a few

hours.

• Increase the frequency of disassembly, inspection and lubrication of the following:

- Front and rear axle hub assembly bearings.

- All transmission cases, gears and differentials.

- Motor—clean with an aerosol motor cleaner and re-oil the bushings

with lightweight motor oil.

WATER-RESISTANT VEHICLE WITH WATERPROOF ELECTRONICS

QUICK START

Please read the entire manual to gain a full understanding of the 22S RTR vehicle, ﬁ ne-tuning the setup and performing maintenance.

1. Read the safety precautions found in this manual.

2. Charge a battery for the vehicle. Refer to your charger's instruction manual

for charging information and warnings.

3. Install the AA batteries in the transmitter. Only use alkaline

or rechargeable batteries.

4. Install the fully charged battery in the vehicle.

5. Power ON the transmitter and then the vehicle. Wait 5 seconds for the ESC to

initialize. Always power the transmitter ON before the vehicle and power it

OFF after the vehicle has been powered OFF.

6. Check the steering and throttle control directions. Verify that the servos are

moving in the correct direction.

7. Drive your vehicle.

8. Power OFF the vehicle and then the transmitter.

9. Unplug the battery and remove it from the vehicle.

10. Perform any necessary maintenance.

CHARGING THE BATTERY

COMPONENTS

• Losi

22S SCT™ RTR: 1/10-Scale 2WD Short Course Truck

• Spektrum™

STX2

2-CH 2.4GHz FHSS Transmitter (SPMSTX200)

• Spektrum™

6KG Waterproof Servo (SPMS606)

• Spektrum™ SRX200 2-CH Receiver (SPMSRX200)

• Dynamite

12-Turn 550 Brushed Motor (DYNS1222)

• Dynamite

60A WP Brushed ESC (DYNS2210)

• 4 AA batteries (for transmitter)

Choose a battery designed to work with the Dynamite

60A WP Brushed ESC. We recommend

the Dynamite

7.4 5000mAh 2S 50C LiPo: Hardcase with EC3™ connector (DYNB33802EC).

Choose a charger designed to charge 2S batteries.

We recommend the Dynamite

Prophet™ Sport Li-Po 35W AC Battery Charger (DYNC2005CA).

Refer to your battery and charger manuals for usage, safety, and charging information.

22S SCT RTR: 1:10 2WD SHORT COURSE TRUCK • INSTRUCTION MANUAL

INSTALLING THE BATTERY

1. Ensure the ESC is powered OFF.

2. Rotate the battery hatch lock to align the ﬂ at section with the edge of the battery hatch.

3. Open the battery hatch.

4. Install the fully charged battery in the vehicle.

5. Close the battery hatch and rotate the lock fully to secure the hatch.

6. Connect the battery to the ESC noting the correct polarity.

7. Power ON the transmitter, then the vehicle.

INSTALLING TRANSMITTER BATTERIES

This transmitter requires 4 AA batteries.

1. Remove the battery cover from the transmitter.

2. Install the batteries as shown.

3. Install the battery cover.

TRANSMITTER CONTROLS

2.4GHZ DIGITAL

RADIO SYSTEM

1. Steering Wheel Controls direction (left/right) of the model

2. Throttle Trigger Controls speed and direction (forward/brake/reverse) of the model

3. ON/OFF Switch Turns the power ON/OFF for the transmitter

4. Throttle Limiting Switch Adjusts the throttle limit from 50%, 75%, and 100%

5. TH Rate Adjusts the end point of the throttle

6. TH Trim Adjusts the throttle neutral point

7. TH REV Reverses the function of the speed control when pulled back or pushed forward

8. ST REV Reverses the function of the steering when the wheel is turned left or right

9. ST Trim Adjusts the steering center point

10. ST Rate Adjusts the end point of the steering

11. Antenna Transmits the signal to the model

12. Indicator Lights

Solid red lights—indicates radio connectivity and adequate battery power

Flashing red lights—indicates the battery voltage is critically low. Replace batteries

CAUTION: NEVER remove the transmitter batteries while the model is

powered on. Loss of model control, damage or injury may occur.

CAUTION: If using rechargeable batteries, charge only rechargeable

batteries. Charging non-rechargeable batteries may cause the batteries to

burst, resulting in injury to persons and/or damage to property.

CAUTION: Risk of explosion if battery is replaced by an incorrect type.

Dispose of used batteries according to state and local laws.

22S SCT RTR: 1:10 2WD SHORT COURSE TRUCK • INSTRUCTION MANUAL

DRIVING PRECAUTIONS

• Maintain sight of the vehicle at all times.

• Routinely inspect the vehicle for loose wheel hardware.

• Routinely inspect the steering assembly for any loose hardware. Driving the vehicle

off-road can cause fasteners to loosen over time.

• Do not drive the vehicle in tall grass. Doing so can damage the vehicle or electronics.

• Stop driving the vehicle when you notice a lack of power. Driving the vehicle when

the battery is discharged can cause the receiver to power off. If the receiver loses power,

you will lose control of the vehicle. Damage due to an over-discharged Li-Po battery is

not covered under warranty.

CAUTION: Do not discharge a Li-Po battery below 3V per cell. Batteries

discharged to a voltage lower than the lowest approved voltage may become

damaged, resulting in loss of performance and potential ﬁ re when batteries

are charged.

• Do not apply forward or reverse throttle if the vehicle is stuck.

Applying throttle in this instance can damage the motor or ESC.

• After driving the vehicle, allow the electronics to cool before driving the vehicle again.

IMPORTANT: Keep wires away from all moving parts.

POWERING ON THE VEHICLE

1. Center the ST TRIM and TH TRIM dials on the transmitter.

2. Power on the transmitter.

3. Install a fully charged battery pack per the Installing the Battery section.

4. Power on the ESC.

BEFORE RUNNING YOUR VEHICLE

1. Check for free suspension movement. All suspension arms and steering components

should move freely. Any binds will cause the vehicle to handle poorly.

Tip: To increase the ride height and ground clearance of your vehicle, install the included

shock spacers.

2. Charge a battery pack. Always charge the battery pack as per the battery and/or

charger manufacturers’ instructions.

3. Set the transmitter steering trim. Follow the instructions to set the steering trim/subtrim

so that the vehicle drives straight with no input to the steering.

4. Perform a Control Direction Test.

RUN TIME

The largest factor in run time is the capacity of the battery pack. A larger mAh rating

increases the amount of run time experienced.

The condition of a battery pack is also an important factor in both run time and speed.

The battery connectors may become hot during driving. Batteries will lose performance

and capacity over time.

Driving the vehicle from a stop to full speed repeatedly will damage the batteries

and electronics over time. Sudden acceleration will also lead to shorter run times.

TO IMPROVE RUN TIMES

• Keep your vehicle clean and well maintained.

• Allow more airﬂ ow to the ESC and motor.

• Change the gearing to a lower ratio. A lower ratio decreases the operating temperature

of the electronics. Use a smaller pinion gear or larger spur gear to lower the gear ratio.

• Use a battery pack with a higher mAh rating.

• Use the optimum charger to charge battery packs (Visit your local hobby dealer for

more information).

BINDING

Binding is the process of programming the receiver to recognize the GUID (Globally Unique

Identiﬁ er) code of a single speciﬁ c transmitter. The STX2

transmitter and SPMSRX200

receiver are bound at the factory. If you need to rebind, follow the instructions below.

1. With the vehicle on a ﬂ at, level surface, insert the Bind Plug in the BIND port on the

receiver.

2. Connect a fully charged battery pack to the ESC.

3. Power on the ESC. The red LED ﬂ ashes, indicating the receiver is in bind mode.

4. Center the ST TRIM and TH TRIM dials on the transmitter.

5. Turn the steering wheel to Full Right. Power the transmitter on while holding the steering

wheel to the Right.

6. Release the steering wheel when the receiver LED stops ﬂ ashing.

7. Remove the Bind Plug, then power off the receiver to save the settings.

8. Power off the transmitter.

9. Remove the bind plug and store it in a convenient place.

You must rebind when:

• Different failsafe positions are desired e.g., when throttle or steering reversing has been

changed.

• Binding the receiver to a different transmitter.

CHANGING THE THROTTLE LIMIT

Beginner Mode

Throttle Limiting Switch: 50%

• Best for learning the basic functions of left, right, stop, brake and reverse

• For use in smaller areas

• Longest battery life

Medium Speed

Throttle Limiting Switch: 75%

• Great top speed and acceleration

• Easier to accelerate in desired direction, especially on loose surfaces when compared to

Maximum Speed setup

• Run time is greatly increased over Maximum Speed setup with an impact to top speed

Maximum Speed (Default)

Throttle Limiting Switch: 100%

• Higher top speeds and maximum acceleration

Throttle Limit Switch

22S SCT RTR: 1:10 2WD SHORT COURSE TRUCK • INSTRUCTION MANUAL

PERFORMING A CONTROL DIRECTION TEST

Perform a control test with the vehicle wheels off the ground. If the wheels rotate after the

vehicle is powered ON, adjust the TH Trim knob until they stop. To make the wheels move

forward, pull the trigger. To reverse them, wait for the wheels to stop, then push the trigger.

When moving forward, the wheels should maintain a straight line without any steering wheel

input. If not, adjust the ST Trim knob, so the wheels maintain a straight line without having to

turn the steering wheel.

ELECTRONIC SPEED CONTROL (ESC)

Part # Description

A DYNS1222 Motor

B DYN9005EC* Battery 7.4V

C SPMS606 Waterproof Steering Servo

D SPMSRX200 Receiver

E DYNS2210 Waterproof Electronic Speed Control (ESC)

F Channel 1

G Channel 2

* Not Included

Operation Tone

Start up One short tone, followed by one long tone.

Low Voltage Cut-Off

When low voltage cuttoff is reached, the vehicle

will slow and emit a continuous tone.

Low Voltage at Start Up

When a low battery is plugged in and powered on,

the vehicle will emit two low tones and power off.

EC3EC3

Programming: The ESC comes with one jumper pre-installed:

BATT: Li-Po conﬁ guration.

The throttle setting without the jumper indicates Throttle/Brake/Reverse. Always use this

setting for this vehicle.

To change the battery type to NiMH, disconnect the jumper from the default port and connect

it to the NiMH port. If the jumper is removed from the BATT port, the default setting is Li-Po

mode. Power off the ESC, then power it back on.

If the jumpers are lost or not installed, the ESC will default to REV: ON and BATT: Li-Po.

WARNING: Only use the NiMH port when using NiMH batteries. Using the

NiMH port with a Li-Po battery can cause serious damage to the battery.

Attempting to charge a damaged battery may result in a ﬁ re.

• Seat the motor brushes by driving smoothly on a ﬂ at surface during use of the ﬁ rst

battery charge. Failing to do so can greatly reduce motor performance

and functional life.

• Prolong motor life by preventing overheating conditions.

Undue motor wear results from frequent turns, stops and starts, pushing objects, driving

in deep water and tall grass, and driving continuously up hill. Allow the motor to

cool completely before running the vehicle.

• Over-temperature protection is installed on the ESC to prevent circuit damage, but

cannot protect the motor from driving against heavy resistance.

MOTOR CARE

22S SCT RTR: 1:10 2WD SHORT COURSE TRUCK • INSTRUCTION MANUAL

PRECAUTIONS

• Never touch moving parts.

• Never disassemble while the batteries are installed.

• Always let parts cool before touching.

GEARING

The 22S SCT includes two pinion gears for different running conditions. The installed 14T

pinion is for running on dirt or other loose surfaces, and driving with lots of stopping and

starting. For driving on hard paved surfaces, and longer speed runs, install the included

18T pinion gear for higher top speeds. Keep in mind that running with the 14T pinion will

increase motor life compared to the 18T pinion.

Installing a pinion gear with fewer teeth or a spur gear with more teeth will increase torque

and reduce top speed. Likewise, a pinion gear with more teeth or a spur gear with fewer

teeth will reduce torque and increase top speed. Take care when installing larger pinion gears

as this can “overgear” the vehicle, resulting in an overheated motor and ESC. When testing

different gearing options, pay close attention to the temperature of the motor and speed

control to ensure you are operating within the correct temperature range. If the motor is too

hot, switch to a lower pinion gear and/or higher spur gear combination.

CAUTION: Do not touch the ESC or motor after use or personal injury

may result. Do not allow the ESC or motor to exceed 160°F (71°C). A

temperature gun (recommended DYNF1055) can be used to safely monitor

the temperature before handling.

CHANGING THE PINION GEAR/GEAR RATIO

1. Remove the screws holding the gear cover in place.

2. Loosen the set screw and remove the installed pinion gear.

3. Loosen the motor screws and slide the motor back.

4. Place the new pinion on the end of the motor shaft so the set screw is located

over the ﬂ at on the shaft.

5. Position it so the teeth line up with the spur gear and secure the pinion by tightening

the set screw.

6. Set the gear mesh.

DYNAMITE

12-TURN 550 BRUSHED MOTOR (DYNS1222)

SETTING THE GEAR MESH

The gear mesh has already been set at the factory. Setting it is only necessary when changing

motors or gears.

Proper gear mesh (how gear teeth meet) is important to the performance of the vehicle. When

the gear mesh is too loose, the spur gear could be damaged by the pinion gear of the motor. If

the mesh is too tight, speed could be limited and the motor and ESC will overheat.

1. Loosen the motor screws and slide the motor back.

2. Put a small piece of paper between the pinion and spur gears.

3. Push the gears together while tightening the motor screws.

4. Remove the paper. Check the mesh at 3–5 different locations around

the spur gear for a small amount of movement.

5. Install gear cover.

NOTICE: For running on street surfaces, or for speed runs, install the

included 18T pinion gear. For running on loose dirt, or other rough terrain

surfaces with stopping and starting, keep the installed 14T pinion gear in

use.

TROUBLESHOOTING GUIDE

PROBLEM POSSIBLE CAUSE SOLUTION

Vehicle does not operate

Battery not charged or plugged in Charge battery/plug in

ESC switch not “ON” Turn on ESC switch

Transmitter not “ON” or low battery Turn on/replace batteries

Motor runs but wheels

do not rotate

Pinion not meshing with spur gear Adjust pinion/spur mesh

Pinion spinning on motor shaft Tighten pinion gear setscrew on motor shaft ﬂ at spot

Transmission gears stripped Replace transmission gears

Drive pin broken Check and replace drive pin

Steering does not work

Servo plug not in receiver properly Make sure the steering servo plug is connected to the receiver steering channel, noting proper polarity

Servo gears or motor damaged Replace or repair servo

Will not turn one direction Servo gears damaged Replace or repair servo

Motor does not run

Motor wire solder joint is damaged Resolder the motor wire with the proper equipment

Motor wire broken Repair or replace as needed

ESC damaged Contact Horizon Hobby Product Support

ESC gets hot

Motor over-geared Use smaller pinion or larger spur gear

Driveline bound up Check wheels and transmission for binding

Poor run time and/or sluggish

acceleration

Battery pack not fully charged Recharge battery

Charger not allowing full charge Try another charger

Driveline bound up Check wheels, transmission for binding

Poor range and/or glitching

Transmitter batteries low Check and replace

Vehicle battery low Recharge battery

Loose plugs or wires Check all wire connections and plugs

LIMITED WARRANTY

What this Warranty Covers

Horizon Hobby, LLC, (Horizon) warrants to the original purchaser that the product purchased

(the “Product”) will be free from defects in materials and workmanship at the date of

purchase.

What is Not Covered

This warranty is not transferable and does not cover (i) cosmetic damage, (ii) damage due

to acts of God, accident, misuse, abuse, negligence, commercial use, or due to improper use,

installation, operation or maintenance, (iii) modiﬁ cation of or to any part of the Product,

(iv) attempted service by anyone other than a Horizon Hobby authorized service center, (v)

Product not purchased from an authorized Horizon dealer, or (vi) Product not compliant

with applicable technical regulations or (vii) use that violates any applicable laws, rules, or

regulations.

OTHER THAN THE EXPRESS WARRANTY ABOVE, HORIZON MAKES NO OTHER WARRANTY

OR REPRESENTATION, AND HEREBY DISCLAIMS ANY AND ALL IMPLIED WARRANTIES,

INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF NON-INFRINGEMENT,

MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE PURCHASER

ACKNOWLEDGES THAT THEY ALONE HAVE DETERMINED THAT THE PRODUCT WILL SUITABLY

MEET THE REQUIREMENTS OF THE PURCHASER’S INTENDED USE.

Purchaser’s Remedy

Horizon’s sole obligation and purchaser’s sole and exclusive remedy shall be that Horizon

will, at its option, either (i) service, or (ii) replace, any Product determined by Horizon to be

defective. Horizon reserves the right to inspect any and all Product(s) involved in a warranty

claim. Service or replacement decisions are at the sole discretion of Horizon. Proof of purchase

is required for all warranty claims. SERVICE OR REPLACEMENT AS PROVIDED UNDER THIS

WARRANTY IS THE PURCHASER’S SOLE AND EXCLUSIVE REMEDY.

Limitation of Liability

HORIZON SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL

DAMAGES, LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY WAY,

REGARDLESS OF WHETHER SUCH CLAIM IS BASED IN CONTRACT, WARRANTY, TORT,

NEGLIGENCE, STRICT LIABILITY OR ANY OTHER THEORY OF LIABILITY, EVEN IF HORIZON HAS

22S SCT RTR: 1:10 2WD SHORT COURSE TRUCK • INSTRUCTION MANUAL

EU Compliance Statement: Horizon Hobby, LLC hereby declares that this

product is in compliance with the essential requirements and other relevant

provisions of the RED and EMC Directive.

A copy of the EU Declaration of Conformity is available online at:

http://www.horizonhobby.com/content/support-render-compliance.

INSTRUCTIONS FOR DISPOSAL OF WEEE BY USERS IN

THE EUROPEAN UNION

This product must not be disposed of with other waste. Instead, it is the user’s

responsibility to dispose of their waste equipment by handing it over to a

designated collections point for the recycling of waste electrical and electronic

equipment. The separate collection and recycling of your waste equipment at

the time of disposal will help to conserve natural resources and ensure that it is recycled in a

manner that protects human health and the environment. For more information about where

you can drop off your waste equipment for recycling, please contact your local city ofﬁ ce, your

household waste disposal service or where you purchased the product.

Country of Purchase Horizon Hobby Contact Information Address

United States of America

Horizon Service Center

(Repairs and Repair Requests)

servicecenter.horizonhobby.com/RequestForm/

2904 Research Road

Champaign, Illinois 61822 USA*

Horizon Product Support

(Product Technical Assistance)

productsupport@horizonhobby.com

877-504-0233

Sales websales@horizonhobby.com 800-338-4639

European Union

Horizon Technischer Service

service@horizonhobby.eu +49 (0) 4121 2655 100

Hanskampring 9

D 22885 Barsbüttel, GermanySales: Horizon Hobby GmbH

WARRANTY AND SERVICE CONTACT INFORMATION

FCC STATEMENT

FCC ID: 2AI3D-SS0001

This equipment has been tested and found to comply with the limits for Part 15 of the FCC

rules. These limits are designed to provide reasonable protection against harmful interference

in a residential installation. This equipment generates uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may cause harmful

interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If

this equipment does cause harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment to an outlet on a circuit different from that to which the receiver

is connected.

• Consult the dealer or an experienced radio/TV technician for help.

This device complies with part 15 of the FCC rules. Operation is subject to the following two

conditions: (1) This device may not cause harmful interference, and (2) this device must accept

any interference received, including interference that may cause undesired operation.

NOTICE: Modiﬁ cations to this product will void the user’s authority to operate this equipment.

IC INFORMATION

IC ID: 21682-SSTC9202

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is

subject to the following two conditions: (1) this device may not cause interference, and (2)

this device must accept any interference, including interference that may cause undesired

operation of the device.

BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Further, in no event shall the liability

of Horizon exceed the individual price of the Product on which liability is asserted. As Horizon

has no control over use, setup, ﬁ nal assembly, modiﬁ cation or misuse, no liability shall be

assumed nor accepted for any resulting damage or injury. By the act of use, setup or assembly,

the user accepts all resulting liability. If you as the purchaser or user are not prepared to

accept the liability associated with the use of the Product, purchaser is advised to return the

Product immediately in new and unused condition to the place of purchase.

Law

These terms are governed by Illinois law (without regard to conﬂ ict of law principals). This

warranty gives you speciﬁ c legal rights, and you may also have other rights which vary from

state to state. Horizon reserves the right to change or modify this warranty at any time

without notice.

WARRANTY SERVICES

Questions, Assistance, and Services

Your local hobby store and/or place of purchase cannot provide warranty support or service.

Once assembly, setup or use of the Product has been started, you must contact your local

distributor or Horizon directly. This will enable Horizon to better answer your questions and

service you in the event that you may need any assistance. For questions or assistance, please

visit our website at www.horizonhobby.com, submit a Product Support Inquiry, or call the toll

free telephone number referenced in the Warranty and Service Contact Information section to

speak with a Product Support representative.

Inspection or Services

If this Product needs to be inspected or serviced and is compliant in the country you live

and use the Product in, please use the Horizon Online Service Request submission process

found on our website or call Horizon to obtain a Return Merchandise Authorization (RMA)

number. Pack the Product securely using a shipping carton. Please note that original boxes

may be included, but are not designed to withstand the rigors of shipping without additional

protection. Ship via a carrier that provides tracking and insurance for lost or damaged parcels,

as Horizon is not responsible for merchandise until it arrives and is accepted at our facility.

An Online Service Request is available at http://www.horizonhobby.com/content/service-

center_render-service-center. If you do not have internet access, please contact Horizon

Product Support to obtain a RMA number along with instructions for submitting your product

for service. When calling Horizon, you will be asked to provide your complete name, street

address, email address and phone number where you can be reached during business hours.

When sending product into Horizon, please include your RMA number, a list of the included

items, and a brief summary of the problem. A copy of your original sales receipt must be

included for warranty consideration. Be sure your name, address, and RMA number are clearly

written on the outside of the shipping carton.

NOTICE: Do not ship Li-Po batteries to Horizon. If you have any issue with a

Li-Po battery, please contact the appropriate Horizon Product Support ofﬁ ce.

Warranty Requirements

For Warranty consideration, you must include your original sales receipt verifying

the proof-of-purchase date. Provided warranty conditions have been met, your Product

will be serviced or replaced free of charge. Service or replacement decisions are at the sole

discretion of Horizon.

Non-Warranty Service

Should your service not be covered by warranty, service will be completed and

payment will be required without notiﬁ cation or estimate of the expense unless

the expense exceeds 50% of the retail purchase cost. By submitting the item for

service you are agreeing to payment of the service without notiﬁ cation. Service estimates are

available upon request. You must include this request with your item submitted for service.

Non-warranty service estimates will be billed a minimum of ½ hour of labor. In addition you

will be billed for return freight. Horizon accepts money orders and cashier’s checks, as well as

Visa, MasterCard, American Express, and Discover cards. By submitting any item to Horizon for

service, you are agreeing to Horizon’s Terms and Conditions found on our website http://www.

horizonhobby.com/content/service-center_render-service-center.

ATTENTION: Horizon service is limited to Product compliant in the country of use

and ownership. If received, a non-compliant Product will not be serviced. Further,

the sender will be responsible for arranging return shipment of the

un-serviced Product, through a carrier of the sender’s choice and at the sender’s

expense. Horizon will hold non-compliant Product for a period of

60 days from notiﬁ cation, after which it will be discarded. 10/15

COMPLIANCE INFORMATION FOR THE EUROPEAN UNION

*For the most up-to-date customer service contact information, please visit: www.horizonhobby.com/content/service-center-render-service-center

22S SCT RTR: 1:10 2WD SHORT COURSE TRUCK • INSTRUCTION MANUAL

Part # English Deutsch Français Italiano

DYNS1222 DYN 550 12-Turn Brushed Motor DYN-550-12-Gang-Bürstenmotor Motore con spazzole 12 giri DYN 550 Moteur à balais DYN 550 12T

DYNS2210 60A FWD/REV Brushed ESC 60A Vorwärts/Rückwärts Bürstenregler

Variateur 60A Marche Av/Arr pour moteur à

charbon

60A FWD/REV regolatore a spazzole

LOS230060 Kicker Audio Body Set: 22S SCT Kicker-Audio-Gehäusesatz: 22S SCT Kit corpo audio: 22S SCT

Ensemble de carrosserie Kicker Audio: 22S

SCT

LOS230061 Magnaﬂ ow Body Set: 22S SCT Magnaﬂ ow-Gehäusesatz: 22S SCT Kit carrozzeria Magnaﬂ ow: 22S SCT Ensemble de carrosserie Magnaﬂ ow: 22S SCT

LOS231034 Mud Flaps Schmutzfänger Bavettes de garde-boue Parafanghi

LOS231042 Chassis Fahrgestell Châssis Telaio

LOS231043 Composite Steering Set Komposit-Lenkungssatz Ensemble de direction composite Set sterzo in composito

LOS231044 Chassis Mounting Set Fahrgestellstützsatz Support châssis Set supporto telaio

LOS231045 Bulkhead Camber Black, Servo Mount Spritzwandsturz schwarz, Servohalterung Support de suspension, noir, support du servo Paratia camber nero, supporto servo

LOS231046 Steering Hardware Set Hardwaresatz Lenkung Ensemble de matériel de direction Set bulloneria sterzo

LOS231047 Body Mount Set Karosseriehalterungssatz Support de carrosserie Set Supporto Carrozzeria

LOS231048 Front Bumper Set Frontstoßstangensatz Pare-choc avant Set paraurti anteriore

LOS231049 Rear Bumper Set Heckstoßstangensatz Pare-choc arrière Set paraurti posteriore

LOS231050 Steering Bearing Set Lenklagersatz Ensemble de roulement de direction Set cuscinetti sterzo

LOS231051 Battery Mounting Foams Schaumstoffe Akku-Halterung Mousses de montage de batteries Schiuma di montaggio per batteria

LOS232036 Gear Cover and Motor Guard Getriebeabdeckung und Motorschutz Cache de l’engrenage et protection moteur Coperchio pignone e protezione motore

LOS232037 Transmission Case Getriebeabdeckung Boîtier de transmission Scatola del cambio

LOS232038 Spur Gear and Slipper Pad 48P 84T Stirnrad und Gleitkissen 48P 84T

Engrenage cylindrique et sabot de piston 48P

84T

Corona e pattino scorrevole 48P 84T

LOS232039 Complete Gear Differential Komplettes Getriebe Differential Engrenage différentiel complet Differenziale pignone completo

LOS232040 Gear Set, Gear Differential Getriebesatz, Getriebe Differential Ensemble d’engrenages, engrenage différentiel Set pignone, differenziale pignone

LOS232041 Motor Plate Motorplatte Plaque moteur Piastra motore

LOS232042 Idler Gear and Shaft Zwischenrad und Welle Axe de pignon intermédiaire Ingranaggio e albero folle

LOS232043 Layshaft and Gear Zwischenwelle und Getriebe Arbre intermédiaire et engrenage Albero secondario e ingranaggio

LOS232044 Front Axle Vorderachse Essieu avant Assale anteriore

LOS232045 CVA Driveshaft, Complete CVA-Antriebswelle, komplett Arbres de transmission CVA, complet Albero di trasmissione CVA completo

LOS232046 Gear Differential Rebuild Set Nachbausatz Getriebe Differential

Ensemble de reconstruction de l’engrenage

différentiel

Set differenziale pignone rigenerato

LOS232047 Slipper Hardware Set Hardwaresatz Gleiter Ensemble de matériel du sabot Set bulloneria scorrevole

LOS232048 Wheel Hex Set Radsechskantsatz (4) Hexagones de roues (4) Set esagoni ruote (4)

LOS233016 Front Shock Set, Complete Kompletter Vorderer Stoßdämpfersatz Lot d’amortisseurs avant, complet Set ammortizzatore anteriore completo

LOS233017 Rear Shock Set, Complete Kompletter Hinterer Stoßdämpfersatz Lot d’amortisseurs arrière, complet Set ammortizzatore posteriore completo

LOS233018 Shock Body Set Stoßdämpfergehäusesatz Carrosserie amortisseurs Set corpo ammortizzatore

LOS233019 Shock Shaft Set Kolbenstangensatz Lot de bras d’amortisseurs Set albero ammortizzatore

LOS233020 Spring Set Federsatz Ressort Set molle

LOS233021 Spring Cups and Clip Set Satz mit Federtellern und Clips Lot de coupelles de ressort et d’attaches Set molle, coppe e clip

LOS233022 Shock Seal Set Stoßdämpferdichtungssatz Lot de joints d’amortisseurs Set guarnizioni ammortizzatore

LOS233023 Shock Caps (2) Stoßdämpferkappen (2) Capuchons d’amortisseurs (2) Tappi ammortizzatore (2)

LOS233024 Shock Ends Stoßdämpferenden Extrémités d’amortisseurs Terminali ammortizzatore

LOS234024 Suspension Arm Set Aufhängungsarmsatz Lot de bras de suspension Set braccetti sospensioni

LOS234025 Front Caster Block Set Vorderradblocksatz Lot de blocs de roulettes avant Set blocco ruota anteriore

LOS234026 Hub and Spindle Set Satz aus Nabe und Spindel Lot de moyeux et de fusées Set mozzo e fuselli

LOS234027 Camber and Steering Link Set Satz aus Sturz und Lenkstange Lot de timonerie de direction et de la chambre Set camber e braccetti sterzo

LOS234028 Shock Tower Set Stossdämpfersatz Support d’amortisseurs Set Torre Ammortizzatore

LOS234029 Pivot Set Drehgelenksatz Lot pivot Set perni

LOS234030 Aluminum Front Chassis Plate Vordere Aluminium-Karosserieplatte Plaque châssis avant en aluminium Piastra anteriore telaio in alluminio

LOS234031 Aluminum Rear Chassis Plate Hintere Aluminium-Karosserieplatte Plaque châssis arrière en aluminium Piastra posteriore telaio in alluminio

LOS234032 Hinge Pin Set Scharnierbolzensatz Lot de charnière Set piastrine per perni

LOS234033 Hinge Pin Lock Screws Scharnierbolzen-Sicherungsstifte Vis de blocage de charnière Viti di supporto piastrine per perni

LOS234034 Ball Stud, 4.8mm x 6mm (4) Kugelzapfen, 4,8mm x 6mm (4) Piton à rotule, 4,8mm x 6mm (4) Viti a sfera, 4,8 mm x 6 mm (4)

LOS235003 Cap Head Screws M3 x 6mm (10) Inbusschrauben M3 x 6mm (10) Vis à tête bombée, M3 x 6mm (10) Viti a testa cilindrica, M3 x 6 mm (10)

LOS235018 Set Screws, M3 X 3mm (10) Stellschrauben, M3 x 3mm (10) Vis de ﬁ xation, M3 x 3mm (10) Viti di fermo, M3 x 3 mm (10)

LOS235024 Button Head Screws M3 x 25mm (10) Halbrundschrauben, M3 x 25mm (10) Vis à tête bombée M3 x 25mm (10) Viti a testa tonda, M3 x 25 mm (10)

LOS235028 Flat Head Screws M3 x 45mm (6) Flachkopfschrauben, M3 x 45mm (6) Vis à tête fraisée, M3 x 45mm (6) Viti a testa piatta, M3 x 45 mm (6)

LOS235029 Cap Head Screws M2 x 4mm (10) Inbusschrauben M2 x 4mm (10) Vis à tête bombée, M2 x 4mm (10) Viti a testa cilindrica, M2 x 4 mm (10)

LOS4114 48 Pitch Pinion Gear,14T 48 Pitchzahnradgetriebe, 14T Engrenage à pignons pas 48, 14T Pignone 48P, 14T

LOS4118 48 Pitch Pinion Gear,18T 48 Pitchzahnradgetriebe, 18T Engrenage à pignons pas 48, 18T Pignone 48P, 18T

LOS43015 Wheel and Tire Mounted (2) Montiertes Rad und Reifen (2) Support volant et pneu (2) Ruota con pneumatico montato (2)

LOSA6937 5 x 10mm Shielded Ball Bearing (2) 5 x 10mm abgedichtetes Kugellager (2) Roulement à billes blindé 5 x 10mm (2) Cuscinetti a sfera schermati 5 x 10 mm (2)

LOSA6955 5 x 13mm HD Clutch Bearings (2) 5 x 13mm HD Kupplungslager (2)

Roulements à embrayage ultra-résistant 5 x

13mm (2)

Cuscinetti frizione HD 5 x 13mm (2)

LOSA6957 10 x 15 x 4mm BB (2) w/ Nylon Retainer 10 x 15 x 4mm BB (2) mit Nylon-Halter

Roulements à billes 10 x 15 x 4mm (0) avec

bague de retenue en nylon

Cuscinetto a sfera 10 x 15 x 4mm (2) con

fermo in nylon

SPMS606 Standard, WP, Plastic Gear Servo Standard, WP, Kunststoffgetriebe-Servo Standard, WP, Servo ingranaggio in plastica

Standard, étanche, Servo à engrenage en

plastique

SPMSRX200 STX2 2CH Radio STX2 2-Kanal Fernsteuerung Émetteur STX2 2 voies Trasmittente STX2 2 canali

SPMSTX200 2-Ch Receiver 2 Kanal Empfänger Récepteur 2 voies Ricevitore

TLR235004 Flat Head Screws, M3 x 25mm (10) Flachkopfschrauben, M3 x 25mm (10) Vis à tête fraisée, M3 x 25mm (10) Viti a testa piatta, M3 x 25 mm (10)

REPLACEMENT PARTS // TEILELISTE // LISTE DES PIÈCES DE RECHANGE // ELENCO DEI RICAMBI

22S SCT RTR: 1:10 2WD SHORT COURSE TRUCK • INSTRUCTION MANUAL

Part # English Deutsch Français Italiano

TLR235007 Flat Head Screws M2.5 x 10mm (10) Flachkopfschrauben, M2.5 x 10mm (10) Vis à tête fraisée, M2.5 x 10mm (10) Viti a testa piatta, M2.5 x 10 mm (10)

TLR5092 Upper Shock Bushing (4) Oberes Dämpferlager (4) Bague d’amortisseurs supérieurs (4) Boccole ammortizzatore superiore (4)

TLR5900 Button Head Screws, M3 x 5mm (10) Halbrundschrauben, M3 x 5mm (10) Vis à tête bombée M3 x 5mm (10) Viti a testa tonda, M3 x 5 mm (10)

TLR5901 Button Head Screws, M3 x 6mm (10) Halbrundschrauben, M3 x 6mm (10) Vis à tête bombée M3 x 6mm (10) Viti a testa tonda, M3 x 6 mm (10)

TLR5902 Button Head Screws, M3 x 8mm (10) Halbrundschrauben, M3 x 8mm (10) Vis à tête bombée M3 x 8mm (10) Viti a testa tonda, M3 x 8 mm (10)

TLR5903 Button Head Screws, M3 x 10mm (10) Halbrundschrauben, M3 x 10mm (10) Vis à tête bombée M3 x 10mm (10) Viti a testa tonda, M3 x 10 mm (10)

TLR5904 Button Head Screws, M3 x 12mm (10) Halbrundschrauben, M3 x 12mm (10) Vis à tête bombée M3 x 12mm (10) Viti a testa tonda, M3 x 12 mm (10)

TLR5906 Button Head Screws, M3 x 35mm (10) Halbrundschrauben, M3 x 35mm (10) Vis à tête bombée M3 x 35mm (10) Viti a testa tonda, M3 x 35 mm (10)

TLR5909 Button Head Screws, M3 x 16mm (10) Halbrundschrauben, M3 x 16mm (10) Vis à tête bombée M3 x 16mm (10) Viti a testa tonda, M3 x 16 mm (10)

TLR5910 Button Head Screws M3 x 14mm (10) Halbrundschrauben, M3 x 14mm (10) Vis à tête bombée M3 x 14mm (10) Viti a testa tonda, M3 x 14 mm (10)

TLR5911 Button Head Screws,M3 x 20mm(10) Halbrundschrauben, M3 x 20mm (10) Vis à tête bombée M3 x 20mm (10) Viti a testa tonda, M3 x 20 mm (10)

TLR5912 Button Head Screws, M3 x 54mm (2) Halbrundschrauben, M3 x 54mm (2) Vis à tête bombée M3 x 54mm (2) Viti a testa tonda, M3 x 54 mm (2)

TLR5914 Button Head Screws,M2 x 12mm (10) Halbrundschrauben, M2 x 12 mm (10) Vis à tête bombée M2 x 12mm (10) Viti a testa tonda, M2 x 12 mm (10)

TLR5961 Flat Head Screw, M3 x 8mm (10) TLR Flachkopfschrauben, M3 x 8mm (10) Vis à tête fraisée M3 x 8mm (10) Vite a testa piatta, M3 x 8mm (10)

TLR5962 Flat Head Screw, M3 x 10mm (10) TLR Flachkopfschrauben, M3 x 10mm (10) Vis à tête fraisée M3 x 10mm (10) Vite a testa piatta, M3 x 10mm (10)

TLR5963 Flat Head Screw, M3 x 12mm (10) TLR Flachkopfschrauben, M3 x 12mm (10) Vis à tête fraisée M3 x 12mm (10) Vite a testa piatta, M3 x 12mm (10)

TLR6105 E-Clips, 3mm Shaft (12) Antriebklammern, 3mm (12) Clips pour arbre 3mm (12) Clips 3 mm (12)

TLR6276 Set Screw, M2.5 x 5mm, Cup Point (10)

TLR Schraubenset, M2.5 x 5mm, Cup Point

(10)

Vis sans tête bout bombé M2,5x5mm (10) Grano, M2.5 x 5mm, punta piana (10)

TLR6288 Set Screw, M3 x 2.5mm (10) TLR Schraubenset, M3 x 2.5mm (10) Vis sans tête, M3 x 2.5mm (10) Grano, M3 x 2.5mm (10)

TLR6313 Locknut, M3 x .5 x 5.5mm (10)

TLR Mutter selbstsichernd M3 x .5 x 5.5mm

(10)

Ecrou M3 x 0,5 x 5,5mm (10) Dado autobloccante, M3 x .5 x 5.5mm (10)

TLR6352 Washers, M3 (10) TLR U-Scheibe, M3 (10) Rondelles M3 (10) Rodelle, M3 (10)

TLR8202 Body Clips, Black (12): 22 TLR Karosserieklammern Schwarz (12): 22 22 - Clips de carrosserie noirs (12) Clips carrozzeria, neri (12): 22

VTR235178 M3 x 14mm Flat Head Screw (10) Rundkopfschrauben M3 x 14 mm (10 Stk) Vis CHC, M3 x 14mm (10) Vite con testa a brugola, M3 x 14mm (10)

REPLACEMENT PARTS // TEILELISTE // LISTE DES PIÈCES DE RECHANGE // ELENCO DEI RICAMBI

Part # English Deutsch Français Italiano

DYN1510 Powerstage Bundle - Stage 2 Leistungsteilpaket – Stufe 2 Lot à étage de puissance: étape2 Bundle Powerstage - fase 2

RECOMMENDED PARTS // EMPFOHLENE TEILE // PIÈCES RECOMMANDÉES //

PEZZI RACCOMANDATI

OPTIONAL PARTS // OPTIONALE TEILE // PIÈCES OPTIONNELLES // PARTI OPZIONALI

Part # English Deutsch Français Italiano

DYN2950 8-in-1 Hex Wrench Kit 8-in-1 Sechskantschlüsselsatz

Kit de clés hexagonales 8-en-1

Kit chiave esagonale 8 in 1

DYN4401 GPS Speed Meter GPS-Tachometer

Indicateur de vitesse GPS

Tachimetro GPS

DYN9005EC 7.4V 5000mAh 2S 20C LiPo, Case: EC3 7,4V 5000mA 2S 20C LiPo, Schale: EC3

Batterie Li-Po 7,4V 5000mAh 2S 20C, boîtier:

EC3

7,4 V 5000 mAh 2S 20C LiPo, Case: EC3

LOS230054 MAXXIS Body Set MAXXIS Karosseriesatz Carrosserie MAXXIS Set carrozzeria MAXXIS

LOS230055 K&N Body Set K&N Karosseriesatz Carrosserie K&N Set carrozzeria K&N

LOS230056 Body Set, Clear Karosseriesatz, transparent Carrosserie transparente Set carrozzeria, trasparente

LOS4115 48 Pitch Pinion Gear,15T 48 Pitchzahnradgetriebe, 15T Engrenage à pignons pas 48, 15T Pignone 48P, 15T

LOS4116 48 Pitch Pinion Gear,16T 48 Pitchzahnradgetriebe, 16T Engrenage à pignons pas 48, 16T Pignone 48P, 16T

LOS4117 48 Pitch Pinion Gear,17T 48 Pitchzahnradgetriebe, 17T Engrenage à pignons pas 48, 17T Pignone 48P, 17T

LOS4119 48 Pitch Pinion Gear,19T 48 Pitchzahnradgetriebe, 19T Engrenage à pignons pas 48, 19T Pignone 48P, 19T

LOS4120 48 Pitch Pinion Gear,20T 48 Pitchzahnradgetriebe, 20T Engrenage à pignons pas 48, 20T Pignone 48P, 20T

LOS43006 Wheels (4) Räder (4)

Roues (4)

Ruote (4)

LOS43016 Maxxis Razr MT, SCT Tire (2) Maxxis Razr MT, SCT Reifen (2)

Pneu SCT, Maxxis Razr MT (2)

Maxxis Razr MT, Pneumatici SCT (2)

LOSA99174 Car Stand Fahrzeugständer

Socle

Supporto automodello

TLR232009 HDS Spur Gear 76T 48P Kevlar® HDS Stirnrad 76T 48P Kevlar

Engrenage HDS 76T 48P Kevlar

Corona HDS 76T 48P Kevlar

TLR232010 HDS Spur Gear 78T 48P Kevlar® HDS Stirnrad 78T 48P Kevlar

Engrenage HDS 78T 48P Kevlar

Corona HDS 78T 48P Kevlar

TLR232011 HDS Spur Gear 82T 48P Kevlar® HDS Stirnrad 78T 82P Kevlar

Engrenage HDS 82T 48P Kevlar

Corona HDS 82T 48P Kevlar

TLR336000 4mm Aluminum Serrated Lock Nuts, Black (6) 4mm Aluminium Rändelmutter, schwarz (6)

Contre-écrous en aluminium à embase striée

4mm, noir (6)

Controdado dentato in alluminio 4 mm, nero (6)

TLR336001 4mm Aluminum Serrated Lock Nuts, Blue (6) 4mm Aluminium Rändelmutter, blau (6)

Contre-écrous en aluminium à embase striée

4mm, bleu (6)

Controdado dentato in alluminio 4 mm, blu (6)

TLR74004 Silicone Shock Oil, 25 wt, 2 oz Stoßdämpfer-Silikonöl, 25wt, 59ml (2oz)

Huile de silicone pour amortisseurs, 25wt, 2oz

Olio di silicone ammortizzatore, 25 wt, 2 oz

TLR74005 Silicone Shock Oil, 27.5 wt, 2 oz Stoßdämpfer-Silikonöl, 27,5wt, 59ml (2oz)

Huile de silicone pour amortisseurs, 27,5wt, 2oz

Olio di silicone ammortizzatore, 27,5 wt, 2 oz

TLR74006 Silicone Shock Oil, 30 wt, 2 oz Stoßdämpfer-Silikonöl, 30wt, 59ml (2oz)

Huile de silicone pour amortisseurs, 30wt, 2oz

Olio di silicone ammortizzatore, 30 wt, 2 oz

TLR74008 Silicone Shock Oil, 35 wt, 2 oz Stoßdämpfer-Silikonöl, 35wt, 59ml (2oz)

Huile de silicone pour amortisseurs, 35wt, 2oz

Olio di silicone ammortizzatore, 35 wt, 2 oz

TLR74009 Silicone Shock Oil, 37.5 wt, 2 oz Stoßdämpfer-Silikonöl, 37,5wt, 59ml (2oz)

Huile de silicone pour amortisseurs, 37,5wt, 2oz

Olio di silicone ammortizzatore, 37,5 wt, 2 oz

TLR76000 Tire Glue, Standard Reifenklebemittel, Standard

Colle à pneus, standard

Colla pneumatici, standard

TLR76004 TLR Lok, Threadlock, Blue TLR Schraubensicherungslack Blau

Frein ﬁ let TLR Lok, bleu

TLR Lok, frenaﬁ letti, blu

22S SCT RTR: 1:10 2WD SHORT COURSE TRUCK • INSTRUCTION MANUAL

EXPLODED VIEW // EXPLOSIONSZEICHNUNG // VUE ÉCLATÉE DES PIÈCES // VISTA ESPLOSA DELLE PARTI

TLR8202

LOS43006

LOS230060 - Kicker Audio

LOS230061 - Magnaﬂow

LOS230056 - Clear | Transparent | Transparente | Trasparente

LOS43016

LOS43015

22S SCT RTR: 1:10 2WD SHORT COURSE TRUCK • INSTRUCTION MANUAL

EXPLODED VIEW // EXPLOSIONSZEICHNUNG // VUE ÉCLATÉE DES PIÈCES // VISTA ESPLOSA DELLE PARTI

LOS232043

LOS232036

TLR6313

TLR5900

LOS232047

LOS4118

LOS235003

TLR6352

LOSA6937

LOS232041

LOS232037

TLR5910

TLR5903

LOS232038

TLR5903

TLR5962

LOS235028

LOS232037

LOS232039

LOS232043

LOS232042

LOSA6937

LOS232042

LOSA6937

LOSA6957

LOS232040

LOS232046

LOS232049

TLR5903

TLR5908

LOS231042

TLR5904

LOS231051

LOS231044

SPMSRX200

DYNS2200

LOS231044

TLR5901

22S SCT RTR: 1:10 2WD SHORT COURSE TRUCK • INSTRUCTION MANUAL

EXPLODED VIEW // EXPLOSIONSZEICHNUNG // VUE ÉCLATÉE DES PIÈCES // VISTA ESPLOSA DELLE PARTI

LOS234028

TLR6313

TLR5092

TLR235004

LOS234032

LOS234033

TLR336000

LOS232044

LOS234025

LOS232044

LOS234026

LOS234024

LOS234034

LOS231048

LOS234034

TLR5903

TLR5909

TLR5911

TLR5903

LOS235024

LOS234030

LOS234029

TLR5909

LOS231045

TLR5911

LOS231045

LOS231046

TLR5910

LOS234027

SPMS606

LOS231050

TLR336000

LOS231050

LOS231043

TLR5903

TLR5904

TLR6352

TLR5962

TLR5963

LOS232048

LOSA6937

LOS234033

LOS231047

LOS232044

LOS231043

TLR8202

Front

Shock

LOS233024

LOS233021

LOS233020

LOS233021

LOS233018

LOS233023

LOS233022

LOS233018

LOS233023

LOS235029

LOS233022

LOS233021

LOS233019

LOS233021

22S SCT RTR: 1:10 2WD SHORT COURSE TRUCK • INSTRUCTION MANUAL

EXPLODED VIEW // EXPLOSIONSZEICHNUNG // VUE ÉCLATÉE DES PIÈCES // VISTA ESPLOSA DELLE PARTI

TLR336000

TLR5903

LOS231049

TLR5903

LOS231034

TLR6313

TLR5912

TLR5904

LOS235028

TLR6313

TLR5092

LOS234028

LOS235024

TLR5911

TLR8202

LOS231047

LOS234031

LOS234026

LOS234027

TLR5910

TLR5904

LOS232048

LOSA6943

LOS232045

LOS234024

TLR5904

LOS234029

LOS234032

TLR5902

VTR235178

TLR5963

TLR5962

LOS232036

LOS232045

LOS234033

LOS234032

LOSA6943

Rear

Shock

LOS233021

LOS233018

LOS233021

LOS233024

LOS233023

LOS235029

LOS233022

LOS233021

LOS233020

LOS233019

LOS233018

LOS233021

Losi, 22S, EC3, Dynamite, Prophet and the Horizon Hobby logo are trademarks or registered trademarks of Horizon Hobby, LLC. The Spektrum

trademark is used with permission of Bachmann Industries, Inc. Maxxis, Magnaﬂ ow, Kicker, K&N, and associated logos are property of their

respective owners and are used with permission.

Created 09/18 58354 LOS03022T1/T2

WWW.LOSI.COM

Losi LOS03022T1 Le manuel du propriétaire

Marque: Losi

Modèle: LOS03022T1

Catégorie: Jouets

Taper: Le manuel du propriétaire

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Losi LOS03022T1 Owner's manual

Losi LOS03022T1 Le manuel du propriétaire

Ce manuel convient également à

Losi LOS03022T1 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents