NCR 7882 Installation and Owner's Manual

7882 Scanner

Installation and Owner

Guide

12623

497-0419630

Release D

April 26, 2001

Information Products

RSD-Atlanta

7882 Scanner Installation and Owner Guide

04/01 497-0419630 Release D2 of 58

The program products described in this book are licensed products of NCR

Corporation. It is the policy of NCR to improve products as new technology,

components, software, and firmware become available. Therefore, NCR reserves the

right to change specifications without prior notice. All features, functions, and

operations described herein may not be marketed by NCR in all parts of the world.

Therefore, before using this document, consult your NCR representative or NCR office

for information that is applicable and current.

Contents

Obtaining Additional Information .......................................................................................3

Obtaining Technical Assistance............................................................................................3

NCR 7882 Scanner Mountings..............................................................................................4

Installation Instructions.........................................................................................................5

Step 1 – Installing Power Supply and Interface Cables.......................................................6

Step 2 – Setting Program Parameters and Verifying Host Connection .............................8

Step 3 – Setting Scan Zone...................................................................................................17

Step 4 – Mounting the 7882.................................................................................................20

Operating the Scanner.........................................................................................................23

Cleaning the 7882.................................................................................................................24

Correcting Scanner Problems..............................................................................................25

Interface Information...........................................................................................................27

NCR 7882 Specifications......................................................................................................29

Programming Worksheets...................................................................................................32

ASCII Code Chart................................................................................................................38

Regulatory Information.......................................................................................................39

Laser Safety ..........................................................................................................................42

Programming Tags...............................................................................................................44

Revision Record

Date Pages Issue Remarks

11/27/00 All A First printing.

02/01/01 All B Updated to current product.

03/19/01 All C Updated to current product.

04/26/01 12, 13, 32-37 D Changed parameter default values

7882 Scanner Installation and Owner Guide

497-0419630 Release D 04/01

3

of 58

Obtaining Additional Information

Other Information Products

Order Number Title

B005-0000-1305 NCR 7882 Scanner User Guide

B005-0000-1306 NCR 7882 Scanner Repair Guide

BST0-2121-74 NCR Scanner Programming Tags

BD20-1074-A NCR Scanner/Scale Interface Programmer’s Guide

How To Obtain Information Products

Web Sites

•

http://inforetail.AtlantaGA.NCR.COM

(NCR only)

•

http://www.info.NCR.COM (Anyone)

Online Order

•

Connect System (NCR only)

Phone Order

•

800-543-2010 (US area)

•

622-3727 (VOICEplus)

•

44-181-242-5350 (International)

Fax Order

•

937-445-6245 (US area)

•

44-181-242-5355 (International)

E-Mail

•

Information+Products.Publishing@

DaytonOH.NCR.COM (US area)

•

Management.Order@UnitedKingdom.

NCR.COM (International)

MS-Mail

•

Publishing, Information+Products (US

Area)

SMTP

•

Order, Management UnitedK

(International)

Mail Order

•

NCR Corporation IPP-Dayton

1700 S. Patterson Boulevard

Dayton, OH 45479 USA

•

NCR Corporation

915 High Road

North Finchley

London N12 OHN United Kingdom

Obtaining Technical Assistance

Technical assistance if available as follows.

•

Technical assistance in the United States: 1-800-262-7782

•

Technical assistance in other countries: call your local NCR office

•

To order parts: 1-800-438-7830

Note – If you find any defective parts during installation of a new scanner, contact the

factory at one of the following.

•

Phone: 353-1-8484222 – Extension 2317

•

Fax: 353-1-8484900 – Attention Quality

•

E-mail: slrdubquality@ir.slr.com

7882 Scanner Installation and Owner Guide

04/01 497-0419630 Release D4 of 58

NCR 7882 Scanner Mountings

NCR 7882 Scanner

The NCR 7882 Scanner is a small, compact laser scanner with many of the same

features as the larger scanners. It can be mounted horizontally in a checkstand or

vertically above the checkstand. Various mounts are available for the 7882.

Scanner

Vertical Mount

Top Plate

(Horizontal Mount)

Horizontal Mount

Flat Plate Adapter

Horizontal Mount

7820 Adapter

Horizontal Mount

7852 Adapter

Vertical Mount

With Top Plate

18681

7882 Scanner Installation and Owner Guide

497-0419630 Release D 04/01

5

of 58

Installation Instructions

When installing an NCR 7882, it is recommended that you first mount the Power

Supply and run all the cables. After connecting the unit to the host terminal, make any

necessary programming changes and scan some good tags to verify that the scanner is

communicating with the host terminal. After verifying that everything is working

correctly, mount the unit in the checkstand. If the NCR 7882 does not work properly,

refer to the problem correcting section in this document: Correcting Scanner Problems.

The following flowchart shows the sequence of installation steps. Detailed descriptions

of each step follow.

18682

Installing Power Supply and

Interface Cables

Step 1

Step 2

Step 3

Step 4

Setting Program Parameters and

Verifying Host Connection

Setting the Scan Zone

Mounting the 7882

7882 Scanner Installation and Owner Guide

04/01 497-0419630 Release D6 of 58

Step 1 - Installing Power Supply

and Interface Cables

Connecting the Cables to an NCR 7882 Scanner

The NCR 7882 can be powered through a wall adapter Power Supply (shown in the

following illustration) or directly from the host terminal. The NCR 7882 automatically

detects which power source is being used. In either case, the input voltage to the NCR

7882 should be +12Vdc. The NCR 7882 current never exceeds 600mA.

1.

Locate the Power Supply in the checkstand at least 10 inches (25.4 cm) from the

7882 installed position. Be sure to locate the Power Supply where spilled liquids

cannot fall onto it.

2.

Install the Interface Cable.

3.

Fasten a Tie-Wrap around the Power Cable and the Interface Cable to help secure

the Power Cable.

7882 Scanner

DC

Power Cable

Interface Cable

Host Terminal

Plastic Top Plate

18683

7837 Hand-Held Scanner

Power Supply

7882 Scanner Installation and Owner Guide

497-0419630 Release D 04/01

7

of 58

Auxiliary RS-232 Port

The Auxiliary RS-232 Port provides a connection for an RS-232 device such as an

NCR 7837 Hand-Held Scanner. The following table gives wiring information about the

connector.

Auxiliary RS-232 Port

Pin Number Signal Name

1 +5 Vdc

2NC

3GND

4TXD

5RXD

6 + 12 Vdc

7CTS

8RTS

9Frame

10 Frame

NCR 7835/7836

•

1416-C313-0040 – Interface Cable

•

1416-C397-0010 – Extension Cable

NCR 7837

•

1416-C445-0025 – Interface Cable

•

1416-C397-0010 – Extension Cable

The NCR 7882 auxiliary RS-232 port hardware is limited to the following fixed

parameters.

Baud Rage 9600

Parity Odd

Stop Bits 1

Number of Data Bits 7

Hardware Handshaking None

Terminator Character CRLF

UPC-A Prefix Character d

UPC-E Prefix Character d

EAN 8 Prefix Character d

EAN 13 Prefix Character d

Code 128 Prefix Character f

Code 39 Prefix Character a

Interleaved 2 of 5 Prefix Character b

Note – ASCII data cannot be sent from the auxiliary RS-232 port when the NCR 7882 is

set for OCIA Short format. In this case, the 7882 generates an error beep.

When an NCR 7836 is attached to an NCR 7882, the 7836 requires the following

programming.

•

Reset to serial (default values) – Label ZA

•

Enable code ID (default values) – Label FB

7882 Scanner Installation and Owner Guide

04/01 497-0419630 Release D8 of 58

Step 2 - Setting Program

Parameters and Verifying Host

Connection

Now you need to turn on the 7882. After making any necessary program changes, scan

a few tags to verify that the 7882 is communicating with the host terminal.

Turning On the 7882

The 7882 does not have an On/Off switch. Use the circuit breaker switch in the

checkstand that supplies power to the unit as the On/Off switch. Put this switch in the

On position.

Programming the Communication Parameters

Caution: Some host terminals can corrupt the 7882 program if they are running and

are connected to the 7882 while you are making program changes. Either turn off the

host terminal or disconnect the interface cable before scanning any programming tags.

If the Interface Cable is provided as a kit rather than being included with the 7882, you

can set the communication parameters by scanning the bar code on the label on the

cable package. Standard defaults are set for most RS-232 or OCIA cables. If the cable is

for a specific host terminal, all the necessary parameters required for that host terminal

are set. The bar code label on the Interface Cable package must be the first bar code

scanned after applying power to the 7882.

If the Interface Cable came with the 7882, the communication parameters are probably

correct and you should not need to make any changes to these parameters. However, if

the 7882 does not communicate with the host terminal, scan the appropriate tag from

the following set of communication protocol tags.

Note – When scanning bar codes on the following pages, be sure to completely cover

all bar codes except the one you are scanning.

7882 Scanner Installation and Owner Guide

497-0419630 Release D 04/01

9

of 58

OCIA Single Cable

NCR 2127, 2154, 2155, 2156, 2157, 2760, 7050, 7051, 7052, 7053, 7054, 7450,

7070

1P1416C0110040

RS-232

NCR 2170, 7452, 7445

ICL 9518/200, 9520/150,

MicroBilt MB-8010 Checkreader,

9-Pin D Shell, 6-Pin Modular

1P1416C0190040

IBM Format

IBM 4683/4 with Port 17,

4694 Models 244/245 Port 9A,

4694 Models 001,004,024 Port 9E,

4693, 4682/3/4 Port 5B

1P1416C0200040

7882 Scanner Installation and Owner Guide

04/01 497-0419630 Release D10 of 58

OCIA Short Format

NCR 2113, 2126, 7058

1P1416C0140040

OCIA Long Format

NCR 1255, 2151, 2152, 2552, 2557, 2950

1P1416C0260040

RS-232 Beetle

SNI Beetle 3L

1P1416C2630040

RS-232 Gilbarco

Gilbarco Controller

1P1416C2370040

7882 Scanner Installation and Owner Guide

497-0419630 Release D 04/01

1

1 of 58

RS-232 Ruby

Verifone Ruby (4M)

1P1416C2540040

RS-232 Wayne

Wayne Controller

1P1416C2360040

7882 Scanner Installation and Owner Guide

04/01 497-0419630 Release D12 of 58

Programming Defaults

Scanning the Default programming tag sets most program parameters to factory

defined values as shown in the following chart. However, some parameters do not

have default values so they are not changed, they stay as they are programmed.

01 Communications Protocol

Protocol No default value – remains as programmed

11 Good Read Tone

Tone On/Off On

Tone Frequency Choice 6 of 8 Levels

Tone Length Choice 3 of 16 Levels

Tone Volume Choice 4 of 8 Levels

Not-On-File Volume Choice 2 of 8 Levels

12 Timers

Lockout Time 750 Milliseconds

Restart Lockout Timer Off

Active Time 15 Minutes

13 Bar Codes – 1

UPC/EAN Enable

Version D Disable

Extend UPC-A To EAN-13 Disable

Extend UPC-E To UPC-A Disable

Periodical Codes Disable

Periodical Code Extension 2-Digit & 5-Digit

Send Data Data As Decoded

14 Bar Codes – 2

Code 39 Disable

Minimum Characters Allowed 8

Full ASCII Disable

Check Digit Present Disable

Transmit Check Digit Disable

Allow 1- or 2-Character Tags Disable

15 Bar Codes – 3

Interleaved 2 of 5 Disable

Bar Code Length Range Check

Value 1 08

Value 2 16

Check Digit Present Disable

Transmit Check Digit Disable

17 Bar Codes – 4

Code 128 Disable

Minimum Data Characters 3

UCC 128 Disable

7882 Scanner Installation and Owner Guide

497-0419630 Release D 04/01

1

3 of 58

16 Label Identifiers

Identifier Type Unique Prefix

Common Byte 1 5D

Common Byte 2 42

Bar Code Type No Default value – remains as programmed

UPC-A UPC-E EAN-8 EAN-13 Code 39 Code 128 I 2 of 5

Common Byte0000222

Unique Identifier 41 Hex 45 Hex 46 Hex 46 Hex 31 Hex 33 Hex 32 Hex

20 RS-232 Parameters – 1

Baud Rate 9600

Parity Odd

Stop Bits & Character Length 1 Stop Bit, 7-Bit Character

Handshake RTS High Wait For CTS

21 RS-232 Parameters – 2

BCC Options Disable

Interface Control None

Check Digit Enable UPC-A, Enable EAN-8,

Enable EAN-13, Disable UPC-E

22 RS-232 Prefix Byte

Prefix Byte Disable

ASCII Code 02

23 RS-232 Terminator Byte

Terminator Byte Enable

ASCII Code 03

24 RS-232 Communications Options

Message Delay 10 Milliseconds

Normal Or Eavesdrop Mode Normal Mode

21 Miscellaneous Parameters

IBM Tone Control Enable

IBM Rexmit Control 3 Times

IBM Tag Data Format Hex

7882 Scanner Installation and Owner Guide

04/01 497-0419630 Release D14 of 58

Making Other Program Changes

If you still need to make program changes after setting the communication parameters,

you can enter information directly from the Programming Worksheets. The

Programming Worksheets, located at the back of this book, identify all the available

program parameters. Each worksheet relates to a specific programming mode. Most

programming options have defaults, identified by a heavy box, that are determined at

the factory. Scanning the Default tag as the first tag after applying power to the 7882

sets the parameters to these values.

Changing the 7882 program is accomplished by scanning the proper sequence of

programming tags, which are included with the unit. Following are three major steps

for making program changes.

1.

Enter the Base Programming State by scanning the Programming Mode tag as the

first tag after applying power to the 7882.

2.

Select a Programming Worksheet and enter its parameter data by scanning the

appropriate Hex tags.

3.

Save the program by scanning the Save and Reset tag.

Note – In most instances the factory determined defaults are the correct parameter

setting. However, if you do need to make changes, it is recommended that you first set

all parameters to default values, then make any necessary changes to the appropriate

parameters.

7882 Scanner Installation and Owner Guide

497-0419630 Release D 04/01

1

5 of 58

Scan Sample Tags

Now you should scan some sample tags to verify that the 7882 is communicating with

the host terminal. Following are four good tags that you can use. After verifying that

the 7882 is communicating properly with the host terminal, continue with the

installation.

Note – For maximum performance, full size labels must be used. The UPC Symbol

Specification Manual gives the exact size requirements for UPC labels. If the bar height

is less than specified, more precise presentation to the scanner is required, reducing

productivity.

UPC-A

1

77062 37920

4

Code 39

17706237920

Code 128

17706237920

Interleaved 2 of 5

017706237920

7882 Scanner Installation and Owner Guide

04/01 497-0419630 Release D16 of 58

Determining Label Quality

Many labels in a typical retail environment are unreadable. The following illustration

shows some of the common problems. Vendors and printers regularly supply products

to the market with bar codes that are overprinted, underprinted, or truncated. Some

labels have missing margins. Others may be printed around the corners of packages, or

on media not likely to remain flat when picked up.

01234 6785 9

06

01234 6785 9

06

01234 6785 9

06

R0026

01234 6785 9

06

01234 67859

06

01234 6785 9

06

Bar Code Scratched Bar Code Folded Bar Code Truncated

Bar Code Torn Poor Color Contrast Red Bar Code On

Red Background

The readability of a label depends on variables such as size, placement, color, paper

type, ink viscosity, and package coatings. The middle of a printing run can yield

erroneous labels due to the many variants involved. In particular, poor color contrast

and marginal print quality can make a label hard to read.

UPC bar code requirements are identified in the UPC Symbol Specification Manual

that is published by the Uniform Code Council, Inc. Contact the following for a copy of

this document.

Uniform Code Council, Inc.

8163 Old Yankee Road, Suit J

Dayton, OH 45458

Phone: 513-435-3870

Contact the following for information on Code 39 or "3 of 9" bar code labels.

AIM – USA

634 Alpha Dr.

Pittsburgh, PA 15238-2802

Phone: 412-963-8588

EAN bar code requirements are identified in General Specification for Article

Symbol Marking, Copyright EAN-1977.

7882 Scanner Installation and Owner Guide

497-0419630 Release D 04/01

1

7 of 58

Step 3 - Setting 7882 Scan Zone

The scan zone on a 7882 Scanner can be set to horizontal or vertical. Changing the scan

zone changes the angle of the scan lines coming from the scanner.

16011

Horizontal

Scanning

Vertical

Scanning

You change the scan zone by turning the screw on the bottom of the cabinet. Be sure to

turn the screw all the way in one direction or the other, do not leave it turned part

way.

.

Complies with FDA radiation

Performance standards 21

CFR Subchapter J.

One or more of the U.S. Patents listed below apply:

4,868,375 4,797,551 4,851,667 4,235,018

4,272,675 4,282,426, 4,679,154 5,194,722

5,276,316 5,334,825 5,262,625 5,256,865

5,144,114 5,065,842 5,023,818 5,459,310

5,588,621 5,661,297 5,773,767 5,975,417

This device complies with Part 15 of the FCC Rules. Operation is subject to

the following two conditions: (1) This device may not cause harmful

interference, and (2) this device must accept any interference received

including interference that may cause undesired operation.

This apparatus does not exceed the Class A limits for

radio noise emissions set out in the Radio Interference

Regulations of Canada.

Le présent appareil ñ émet pas de bruits radioeléctriques

depassant les limites de la Classe A prescrites dans le

Reglement sur le brouillage radioeléctrique du Canada.

VCCI-1

Horizontal

Vertical

Duluth, Ga.

30096

NCR Corporation

Scan Zone

Adjusting Screw

18684

When selecting the scan zone, you must also consider how you are mounting the

scanner, horizontally or vertically. This permits you to optimize the performance for

your particular installation. Following are four common installations that identify the

installation type and the scan zone setting. They are given in order of scanning

efficiency with the first being the most efficient, and the last being the least.

7882 Scanner Installation and Owner Guide

04/01 497-0419630 Release D18 of 58

Horizontal - Pass-by Scanning

This installation provides the most efficient way to scan items. It is typically used in

checkouts where speed is extremely important. In this installation, the operator slides

items from the input area on the checkstand, across the scanner, and to the output area

on the checkstand.

16012

Typical Installation -

Hyper/Super Market

Scan Zone - Horizontal

Installation - Horizontal

Vertical - Pass-by Scanning

This installation is used where the checkstand is not large enough to mount the

scanner horizontally, but pass-by scanning is needed. In this installation, the operator

slides items from the input area on the checkstand, past the scanner, and to the output

area on the checkstand.

Typical Installation -

Drug Stores

Super Market in Europe

With Operator Seated

Scan Zone - Horizontal

Installation - Vertical

16013

OR

7882 Scanner Installation and Owner Guide

497-0419630 Release D 04/01

1

9 of 58

Vertical - Presentation Scanning from Top

This installation is used on small checkout counters that do not have enough room for

pass-by scanning. Here the operator picks up the item, presents it toward the top of the

scanner, then bags the item all in one motion.

16014

Typical Installation -

Specialty Store

Scan Zone - Vertical

Installation - Vertical

Vertical - Presentation Scanning from Bottom

This installation is used on very small checkout counters. In this installation the

operator picks up the item, presents it toward the bottom of the scanner, then bags the

item all in one motion.

16015

Typical Installation -

Convenient Store

Scan Zone - Vertical

Installation - Vertical

7882 Scanner Installation and Owner Guide

04/01 497-0419630 Release D20 of 58

Step 4 - Mounting the 7882

Rubber Feet

The NCR 7882 Scanner is supplied with rubber feet that can be attached to the sides of

the cabinet. This permits the scanner to sit on the checkstand in a vertical position

without being mounted to the Vertical Mounting Bracket. There are round recesses in

each side of the cabinet that accept the rubber feet. Remove the paper backing from the

rubber feet and stick them to the cabinet in the round recesses.

Plastic Top Plate

Your installation may use a Plastic Top Plate. Make sure no rubber feet are attached to

the cabinet.

1.

Properly align the scanner with the Plastic Top Plate.

2.

Fasten the scanner to the Top Plate making sure that all four latches are securely

latched around the scanner.

Plastic Top Plate

Mounting Latches

18718B

NCR 7882

La page charge ...

NCR 7882 Installation and Owner's Manual

NCR 7882 Installation and Owner's Manual

dans d''autres langues

Documents connexes

Autres documents