Hitachi NV 45AB2(S) Manuel utilisateur

Marque: Hitachi

Modèle: NV 45AB2(S)

Catégorie: Cloueuse

Taper: Manuel utilisateur

Model Nailer

Modèle Cloueur

Modelo Clavador

NV 45AB2

NV 45AB2(S)

DANGER

Improper use of this Nailer can result in death or serious injury!

This Manual contains important information about product safety.

Read and understand this Manual before operating the Nailer.

Never allow anyone who has not reviewed this manual.

PELIGRO

¡La utilización inadecuada e insegura de este clavador puede resultar en lesiones serias o en la

muerte!

Este manual contiene información importante sobre la seguridad del producto.

Lea y entienda este manual antes de utilizar el clavador.

No deje manejar esta herramienta a nadie que no haya leído este manual.

Instruction and safety manual

Manuel d’instructions et de securite

Iinstrucciones y manual de seguridad

DANGER

Une utilisation incorrecte et sans respecter la sécurité de ce cloueur risque d’entraîner la mort

ou des blessures graves !

Ce manuel renferme des instructions importantes sur la sécurité de l’outil.

Lire et bien assimiler ce manuel avant d’utiliser le cloueur.

Ne jamais laisser les personnes n'ayant pas étutdié le manuel utiliser l'outil.

NV45AB2 NV45AB2(S)

CONTENTS

TABLE DE MATIERES

INDICE

Français

Page

APPLICATIONS ......................................................................27

AVANT L’UTILISATION.........................................................27

ENVIRONNEMENT DE TRAVAIL ....................................27

ALIMENTATION D’AIR ....................................................27

GRAISSAGE .....................................................................28

ENTRETIEN PAR TEMPS FROID.....................................28

ESSAI DU CLOUEUR.......................................................28

RÉGLAGE DE LA PRESSION D’AIR ................................29

CHARGEMENT DES CLOUS ...........................................29

UTILISATION DU CLOUEUR ................................................31

MÉTHODES D’UTILISATION ..........................................32

UTILISATION DU GUIDE A BARDEAU ..........................33

RÉGLAGE DE LA PROFONDEUR DE CLOUAGE ...........33

ENTRETIEN

ENTRETIEN ET INSPECTION ................................................35

ENTRETIEN ET REPARATIONS ............................................37

LISTE DES PIECES.................................................................58

Español

Página

APLICACIONES......................................................................46

ANTES DE LA OPERACIÓN ..................................................46

ENTORNO DE TRABAJO ................................................46

SUMINISTRO DE AIRE ....................................................46

LUBRICACIÓN .................................................................47

CUIDADOS PARA CLIMAS FRÍOS..................................47

PRUEBA DEL

CLAVADOR

................................................47

AJUSTE DE LA PRESIÓN DE AIRE.................................48

CARGA DE

CLAVOS

.........................................................49

OPERACIÓN DEL

CLAVADOR

...............................................51

MÉTODOS DE OPERACIÓN............................................51

EMPLEO DE LA GUÍA PARA TEJAMANILES.................52

AJUSTE DE LA PROFUNDIDAD DE CLAVADO .............53

MANTENIMIENTO

MANTENIMIENTO E INSPECCIÓN ......................................54

SERVICIO Y REPARACIONES ...............................................56

LISTA DE PIEZAS ..................................................................58

English

Page

APPLICATIONS ......................................................................10

BEFORE OPERATION ............................................................10

WORKING ENVIRONMENT ............................................10

AIR SUPPLY .....................................................................10

LUBRICATION..................................................................11

COLD WEATHER CARE ...................................................11

TESTING THE NAILER.....................................................11

ADJUSTING AIR PRESSURE ..........................................12

LOADING NAILS..............................................................12

NAILER OPERATION .............................................................14

METHODS OF OPERATION ............................................15

USING THE SHINGLE GUIDE .........................................16

ADJUSTING THE NAILING DEPTH ................................16

MAINTENANCE

MAINTENANCE AND INSPECTION .....................................17

SERVICE AND REPAIRS ........................................................18

PART LIST ..............................................................................58

Page

IMPORTANT INFORMATION..................................................3

DEFINITIONS OF SIGNAL WORDS ....................................... 3

SAFETY

IMPORTANT SAFETY INSTRUCTIONS

FOR USING NAILERS........................................................4

IMPORTANT SAFETY INSTRUCTIONS FOR USING

NV45AB2 COIL NAILER.................................................... 7

IMPORTANT SAFETY INSTRUCTIONS FOR USING

NV45AB2(S) COIL NAILER ............................................... 7

EMPLOYER’S RESPONSIBILITIES..........................................7

OPERATION

NAME OF PARTS ....................................................................8

SPECIFICATIONS.................................................................... 9

NAIL SELECTION.................................................................... 9

ACCESSORIES .........................................................................9

STANDARD ACCESSORIES..............................................9

OPTIONAL ACCESSORIES .............................................10

Page

INFORMATION IMPORTANTE .............................................20

DEFINITION DES MOTS DE SIGNALISATION ....................20

SECURITE

CONSIGNES DE SECURITE IMPORTANTES

POUR L’UTILISATION DU CLOUEUR ............................21

IMPORTANTES INSTRUCTIONS DE SECURITE

POUR L’UTILISATION DU CLOUEUR NV45AB2 ...........24

IMPORTANTES INSTRUCTIONS DE SECURITE POUR

L’UTILISATION DU CLOUEUR NV45AB2(S) .................24

RESPONSABILITES DE L’EMPLOYEUR ...............................24

UTILISATION

NOM DES PIECES .................................................................25

SPECIFICATIONS...................................................................26

SELECTION DES CLOUS ......................................................26

ACCESSOIRES .......................................................................26

ACCESSOIRES STANDARD............................................26

ACCESSOIRES EN OPTION ............................................27

Página

INFORMACIÓN IMPORTANTE .............................................39

DEFINICIÓN DE LAS PALABRAS CLAVE .............................39

SEGURIDAD

INSTRUCCIONES IMPORTANTES DE SEGURIDAD

PARA LA UTILIZACIÓN DEL CLAVADOR

..........................40

INSTRUCCIONES IMPORTANTES DE SEGURIDAD PARA

UTILIZAR EL

CLAVADOR

DE RISTRA NV45AB2

.....................43

INSTRUCCIONES IMPORTANTES DE SEGURIDAD PARA UTILIZAR

CLAVADOR

DE RISTRA NV45AB2(S).....................................

RESPONSABILIDADES DEL EMPRESARIO .........................43

OPERACIÓN

NOMENCLATURA .................................................................44

ESPECIFICACIONES ..............................................................45

SELECCIÓN DE

CLAVOS

.......................................................45

ACCESORIOS.........................................................................45

ACCESORIOS ESTÁNDAR ..............................................45

ACCESORIOS OPCIONALES ..........................................46

— 3 —

English

IMPORTANT INFORMATION

Read and understand tool labels and all of the operating instructions, safety

precautions and warnings in this manual before operating or maintaining this nailer.

Failure to follow warnings could result in DEATH or SERIOUS INJURY.

Most accidents that result from the operation and maintenance of Nailers are caused by the failure to observe

basic safety rules or precautions. An accident can often be avoided by recognizing a potentially hazardous

situation before it occurs, and by observing appropriate safety procedures.

Basic safety precautions are outlined in the “SAFETY” section of this Manual and in the sections which

contain the operation and maintenance instructions.

Hazards that must be avoided to prevent bodily injury or machine damage are identified by DANGERS and

WARNINGS on the Nailer and in this Manual.

Never use this Nailer for applications other than those specified in this Manual.

DEFINITIONS OF SIGNAL WORDS

DANGER indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.

WARNING indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.

CAUTION indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury, or

may cause machine damage.

NOTE emphasizes essential information.

— 4 —

English

SAFETY

IMPORTANT SAFETY INSTRUCTIONS

MMMMFOR USING NAILERSMMlMM

READ ALL INSTRUCTIONS

DANGER

1. OPERATORS AND OTHERS IN WORK AREA MUST WEAR SAFETY GLASSES WITH SIDE SHIELDS.

When operating the Nailer, always wear safety glasses with side shields, and make sure others in

work area wear safety glasses, too.

Safety glasses must conform to the requirements of American National Standards Institute, ANSI

Z87.1 and provide protection against flying particles both from the front and side.

The employer must enforce the use of safety glasses by the Nailer operator and others in work

area.

2. NEVER USE OXYGEN OR OTHER BOTTLED GASES. EXPLOSION MAY OCCUR.

Never use oxygen, combustible gases or any other bottled gases as a power source for the Nailer.

Use of the above gases is dangerous, as the Nailer will explode.

Use only clean, dry, regulated compressed air.

WARNING

3. NEVER POINT TOOL AT YOURSELF OR OTHERS IN WORK AREA.

Always assume the Nailer contains fasteners.

Never point the Nailer at yourself toward yourself or others, whether it contains fasteners or not.

If fasteners are mistakenly driven, it can lead to severe injuries.

Never engage in horseplay with the Nailer.

Respect the Nailer as a working implement.

4. KEEP FINGERS AWAY FROM TRIGGER WHEN NOT DRIVING NAILS TO AVOID ACCIDENTAL FIRING.

Never carry the Nailer with finger on trigger since you could drive a fastener unintentionally and injure yourself or

someone else.

Always carry the Nailer by the handle only.

5. CHOICE OF TRIGGERING METHOD IS IMPORTANT.

Please read and understand page 15 of “METHODS OF OPERATION.”

6. DO NOT EXCEED 120 psi. (8.3 bar 8.5 kgf/cm

)

Do not exceed maximum recommended air pressure 120 psi (8.3 bar

8.5 kgf/cm

Never connect the Nailer to pressure which potentially exceeds 200 psi

(13.7 bar 14 kgf/cm

) as the Nailer can burst.

7. ALWAYS WEAR EAR AND HEAD PROTECTION.

Always wear ear protection to protect your ears from loud noise.

Always wear head protection to protect your head from flying objects.

— 5 —

English

8. STORE NAILER PROPERLY.

When not in use, the Nailer should be stored in a dry

place. Keep out of reach of children. Lock the storage

area.

9. KEEP WORK AREA CLEAN.

Cluttered areas invite injuries. Clear all work areas of

unnecessary tools, debris, furniture, etc.

10. NEVER USE IN PRESENCE OF FLAMMABLE

LIQUIDS OR GASES.

The Nailer produces sparks during operation.

Never use the Nailer in sites containing lacquer, paint,

benzine, thinner, gasoline, gases, adhesive agents,

and other materials which are combustible or explosive.

11. KEEP VISITORS AWAY.

Do not let visitors handle the Nailer.

All visitors should be kept safely away from work

area.

12. DRESS PROPERLY.

Do not wear loose clothing or jewelry as they can be

caught in moving parts.

Rubber gloves and nonskid footwear are

recommended when working outdoors.

Wear protective hair covering to contain long hair.

13. NEVER USE NON RELIEVING COUPLER ON

NAILER.

If a non relieving coupler is used on the Nailer, the

Nailer can remain charged with air after disconnecting

and thus will be able to drive a fastener even after

disconnecting.

The Nailer and air hose must have a hose coupling

such that all pressure is removed from the Nailer

when the coupling joint is disconnected.

14. CHECK PUSH LEVER BEFORE USE.

Make sure the push lever operates properly. (The

push lever may be called “Safety”.) Never use the

Nailer unless the push lever is operating properly,

otherwise the Nailer could drive a fastener

unexpectedly. Do not tamper with or remove the push

lever, otherwise the push lever becomes inoperable.

15. KEEP ALL SCREWS AND COVERS TIGHTLY IN

PLACE.

Keep all screws and covers tightly mounted. Check

their condition periodically.

Never use the Nailer if parts are missing or damaged.

16. DO NOT LOAD FASTENERS WITH TRIGGER OR

PUSH LEVER DEPRESSED.

When loading fasteners into the Nailer or when

connecting the air hose,

1) do not depress the trigger;

2) do not depress the push lever; and

3) keep the Nailer pointed downward.

17. KEEP HANDS AND FEET AWAY FROM FIRING

HEAD DURING USE.

Never place your hands or feet closer than 8 inches

(200 mm) from the firing head.

A serious injury can result if the fasteners are

deflected by the workpiece, or are driven away from

the point of entry.

18. PLACE NAILER PROPERLY ON WORKPIECE.

Do not drive fasteners on top of other fasteners or

with the Nailer at too steep of an angle; the fasteners

can ricochet and hurt someone.

19. BE CAREFUL OF DOUBLE FIRE DUE TO RECOIL.

If the push lever is unintentionally allowed to re-contact

the workpiece following recoil, an unwanted fastener

will be driven.

In order to avoid this undesirable double fire,

1) do not push the Nailer on the workpiece with

strong force;

2) take the Nailer completely away from the

workpiece using recoil, and keep the push lever

away from the workpiece until the next desirable

shot; and

3) pull the trigger and release it QUICKLY when

performing intermittent operation (trigger fire).

20. DO NOT DRIVE FASTENERS INTO THIN

BOARDS OR NEAR CORNERS AND EDGES OF

WORKPIECE.

The fasteners can be driven through or away from the

workpiece and hit someone.

21. NEVER DRIVE FASTENERS FROM BOTH SIDES

OF A WALL AT THE SAME TIME.

The fasteners can be driven into and through the wall

and hit a person on the opposite side.

22. CHECK FOR LIVE WIRES.

Avoid the risk of severe electrical shock by checking

for live electrical wires that may be hidden by walls,

floors or ceilings. Turn off the breaker switch to

ensure there are no live wires.

23. NEVER CARRY NAILER BY HOSE.

SAFETY — Continued

WARNING

— 6 —

English

SAFETY — Continued

WARNING

24. DO NOT OVERREACH.

Keep proper footing and balance at all times.

25. NEVER USE NAILER WHICH IS DEFECTIVE OR

OPERATING ABNORMALLY.

If the Nailer appears to be operating unusually,

making strange noises, or otherwise appears

defective, stop using it immediately and arrange for

repairs by a Hitachi authorized service center.

26. DO NOT DISCONNECT AIR HOSE FROM NAILER

WITH FINGER ON TRIGGER.

The Nailer can fire when re-connected to an air supply.

27. DISCONNECT AIR HOSE FROM NAILER WHEN:

1) doing maintenance and inspection;

2) clearing a jam;

3) it is not in use;

4) leaving work area;

5) moving it to another location; and

6) handing it to another person.

Never attempt to clear a jam or repair the Nailer

unless you have disconnected air hose from the Nailer

and removed all remaining fasteners from the Nailer.

The Nailer should never be left unattended since

people who are not familiar with the Nailer might

handle it and injure the themselves.

28. STAY ALERT.

Watch what you are doing. Use common sense.

Do not operate the Nailer when you are tired.

The Nailer should never be used by you if you are

under the influence of alcohol, drugs or medication

that makes you drowsy.

29. HANDLE NAILER CORRECTLY.

Operate the Nailer according to this Manual.

Never allow the Nailer to be operated by children,

individuals unfamiliar with its operation or unauthorized

personnel.

30. NEVER USE NAILER FOR APPLICATIONS OTHER

THAN THOSE SPECIFIED IN THIS MANUAL.

31. HANDLE NAILER CAREFULLY

Because of high air pressure in the Nailer, cracks in

the surface are dangerous.

To avoid this, do not drop the Nailer or strike the

Nailer against hard surfaces; and do not scratch or

engrave signs on the Nailer. Handle the Nailer

carefully.

32. MAINTAIN NAILER WITH CARE.

Keep the Nailer clean and lubricated for better and

safer performance.

33. USE ONLY PARTS, ACCESSORIES OR

FASTENERS SUPPLIED OR RECOMMENDED BY

HITACHI.

Unauthorized parts, accessories, or fasteners may

void your warranty and can lead to malfunction and

resulting injuries.

Only service personnel trained by Hitachi, distributor

or employer shall repair the Nailer.

34. NEVER MODIFY OR ALTER A NAILER.

Doing so may cause it to malfunction and personal

injuries may result.

— 7 —

English

EMPLOYER’S RESPONSIBILITIES

SAVE THIS MANUAL AND

KEEP IT AVAILABLE FOR OTHERS!

IMPORTANT SAFETY INSTRUCTIONS FOR USING

NV45AB2 COIL NAILER

WARNING

1. CLOSE NAIL GUIDE AND DO NOT OPEN IT

DURING OPERATION.

If driving fasteners with the nail guide open, the

fasteners can be driven away from the workpiece.

SAFETY — Continued

2. NEVER USE GASOLINE OR OTHER HIGHLY

FLAMMABLE LIQUIDS FOR CLEANING.

Vapor of such liquids inside the Nailer could be

ignited by a spark produced during nailing, which can

cause an explosion.

IMPORTANT SAFETY INSTRUCTIONS FOR USING

NV45AB2(S) COIL NAILER

WARNING

1. CLOSE NAIL GUIDE AND DO NOT OPEN IT

DURING OPERATION.

If driving fasteners with the nail guide open, the

fasteners can be driven away from the workpiece.

2. DO NOT OPEN MAGAZINE FACING

DOWNWARD WHILE LOADING FASTENERS.

The fasteners can fall down and result in personal

injury.

3. NEVER USE GASOLINE OR OTHER HIGHLY

FLAMMABLE LIQUIDS FOR CLEANING.

Vapor of such liquids inside the Nailer could be

ignited by a spark produced during nailing, which can

cause an explosion.

1. Ensure that this MANUAL is available to operators

and personnel performing maintenance.

2. Ensure that Nailers are used only when operators and

others in work area are wearing EYE PROTECTOR.

3. Enforce the use of EYE PROTECTOR by operators and

others in work area.

4. Keep Nailers in safe working order.

5. Maintain Nailers properly.

6. Ensure that Nailers which require repair are not

further used before repair.

— 8 —

English

OPERATION

NOTE: The information contained in this Manual is designed to assist you in the safe operation of the Nailer.

Some illustrations in this Manual may show details or attachments that differ from those on your own Nailer.

NAME OF PARTS

Feed Piston

Piston

Piston O-ring

Driver Blade

Nose

Adjuster

Push Lever

Cap

Exhaust Cover

Trigger

Body

Air Plug (Sold separately)

Magazine Assembly

Magazine Cover

Nail Holder

Shingle Guide

Feeder

Firing Head (Outlet)

Section A-A

Main Nail Stopper

Nail Guide

Feeder

1–1/2"

1" 1–1/ 4"

7/ 8"

1–3/4"

<NV45AB2(S)>

Magazine Assembly

Magazine Stopper

Shingle Guide

Nail Holder

Magazine Cover

— 9 —

English

SPECIFICATIONS

Model NV45AB2 NV45AB2(S)

Operating pressure 70 – 120 psi (4.9 – 8.3 bar 5 – 8.5 kgf/cm

)

Dimensions 9-27/32" × 10-3/8" × 4-5/8" 9-27/32" × 10-3/8" × 4-7/8"

Length × Height × Width (250 mm × 264 mm × 117 mm) (250 mm × 264 mm × 124 mm)

Weight 5.5 lbs (2.5 kg)

Magazine type Top loading Bottom loading

Nail capacity 120 nails (1 coil)

.046 ft

/cycle at 100 psi

Air consumption (1.3 ltr/cycle at 6.9 bar)

(1.3 ltr/cycle at 7 kgf/cm

)

Air inlet 3/8 NPT Thread

NAIL SELECTION

WARNING

䢇 Be sure to use only the genuine HITACHI nails for the NV45AB2/NV45AB2(S). The use of any other nails can

result in tool malfunction and/or nail breakdown, leading to serious injuries.

Only nails shown in the Table below can be driven with this Nailer.

ACCESSORIES

WARNING

䢇 Accessories other than those shown below can lead to malfunction and resulting injuries.

STANDARD ACCESSORIES

Min. Max.Wire-collated coil nails

123

.413"

(10.5mm)

.120"

(3.05mm)

7/8"(22mm)

.413"

(10.5mm)

.120"

(3.05mm)

1-3/4"(45mm)

1 Eye protection 1

2 Allen wrench for M5 screw 1

3 Allen wrench for M4 screw 1

— 10 —

English

Dust Cap

3/8 NPT Male Plug

Compressor Side

Nailer Side

Filter

Lubricator

Regulator

䡬 Moisture or oil in the air compressor may accelerate

wear and corrosion in the Nailer.

Drain daily.

2. Filter-Regulator-Lubricator

䡬 Use a regulator with a pressure range of 0 – 120 psi

(0 – 8.3 bar 0 – 8.5 kgf/cm

䡬 Filter-regulator-lubricator units supply an optimum

condition for the Nailer and extend the Nailer life.

These units should always be used.

Filter.............The filter removes moisture and dirt

mixed in compressed air.

Drain daily unless fitted with an

automatic drain.

Keep the filter clean by regular

maintenance.

Regulator.....The regulator controls the operating

pressure for safe operation of the Nailer.

Inspect the regulator before operation to

be sure it operates properly.

Lubricator ....The lubricator supplies an oil mist to the

Nailer.

Inspect the lubricator before operation

to be sure the supply of lubricant is

adequate.

Use Hitachi pneumatic tool lubricant.

3. Air hose

Air hose must have a minimum working pressure

rating of 150 psi (10.4 bar 10.6 kgf/cm

) or 150% of the

maximum pressure produced in the system,

whichever is higher.

4. Hose coupling

䡬 The Nailer can be installed as follows:

Remove the dust cap placed at the air inlet.

Install a 3/8 NPT male plug at the air inlet.

䡬 A female coupler must be on the air hose.

The hose coupling (male plug-female coupler) must

remove all pressure from the Nailer when

disconnected.

Never use a non relieving coupler on the Nailer.

OPTIONAL ACCESSORIES

... sold separately

䡬 Sequential Trip Mechanism Kit (Code No. 878226)

(Single Shot Parts)

䡬 Pneumatic Tool Lubricant

1 oz. (30 cc) oil feeder (Code No. 877153)

4 oz. (120 cc) oil feeder (Code No. 874042)

1 quart (1 ltr) can (Code No. 876212)

NOTE: Accessories are subject to change without any

obligation on the part of HITACHI.

APPLICATIONS

䡬 Installation of asphalt roofing shingles in building

contrcution.

䡬 Installation of insulation boards in building

construction.

BEFORE OPERATION

Read section titled “SAFETY” (pages 4 – 7).

Make sure of the followings before operation.

WORKING ENVIRONMENT

WARNING

䢇 No flammable gas, liquid or other flammable

objects at worksite.

䢇 Clear the area of children or unauthorized

personnel.

AIR SUPPLY

DANGER

䢇 NEVER use oxygen or

other bottled gases.

Explosion may occur.

WARNING

䢇 Never connect Nailer to pressure which

potentially exceeds 200 psi (13.7 bar 14 kgf/cm

䢇 Never use non relieving coupler on Nailer.

1. Power source

䡬 Use only clean, dry, regulated compressed air as a

power source for this Nailer.

䡬 Air compressors used to supply compressed air to this

Nailer must comply with the requirements of the latest

version of ANSI Standard B 19.3 “Safety Standard For

Compressors For Process Industries.”

— 11 —

English

psi 80 90 100

Operating pressure (bar) (5.5) (6.2) (6.9)

(kgf/cm

) (5.6) (6.3) (7)

Air consumption

/cycle .033 .039 .046

(ltr/cycle) (.93) (1.1) (1.3)

Trigger

Push Lever

Do not

connect

air hose

5. Air consumption

Using the Air consumption table and the Air

compressor size formula, find a correct compressor

size.

Air consumption table

Air compressor size formula

Amount of air required

=number of Nailers

× average nails driven each minute per Nailer

× air consumption at given air pressure

× safety factor (always 1.2)

Example: 2 Nailers operating at 100 psi driving 30 nails

per minute

Amount of air required

=2 × 30 × .046 (1.3) × 1.2

=3.3 CFM (ft

/min) (94 ltr/min)

After making the calculations as shown above, you

should find a compressor providing 3.3 CFM of air that

is required.

LUBRICATION

It is important that the Nailer be properly lubricated.

Without proper lubrication, the Nailer will not work

properly and parts will wear prematurely.

䡬 Use Hitachi pneumatic tool lubricant.

Do not use detergent oil or additives. These lubricants

will harm the O-rings and other rubber parts. This will

cause the Nailer to malfunction.

䡬 Filter-regulator-lubricator units should always be

used.

Keep the lubricator filled with Hitachi pneumatic tool

lubricant.

䡬 If a lubricator is not available, supply 5 – 10 drops of

Hitachi pneumatic tool lubricant into the air plug on

the Nailer twice a day.

COLD WEATHER CARE

䡬 Do not store the Nailer in a cold weather environment.

Keep the Nailer in a warm area until beginning the

work.

䡬 If the Nailer is already cold, bring it in a warm area

and allow the Nailer to warm up before use.

1 Reduce the air pressure to 64 psi (4.4 bar

4.5 kgf/cm

2 Remove all nails from the Nailer.

3 Connect the air hose and free-fire (blank-fire) the

Nailer.

The lowered air pressure will be enough to free-

fire the Nailer.

Slow speed operation tends to warm up the

moving part.

CAUTION

䢇 Do not free-fire the Nailer at high pressure.

TESTING THE NAILER

DANGER

䢇 Operators and others in

work area MUST wear

safety glasses with side

shields which conforms

to ANSI Z87.1

specifications.

WARNING

䢇 Never use Nailer unless push lever is operating

properly.

Before actually beginning the nailing work, test the Nailer

by using the check list below. Conduct the tests in the

following order.

If abnormal operation occurs, stop using the Nailer and

contact a Hitachi authorized service center immediately.

(1) DISCONNECT AIR HOSE FROM NAILER.

REMOVE ALL NAILS FROM NAILER.

䡺 ALL SCREWS MUST BE TIGHTENED.

If any screws are loose, tighten them.

䡺 THE PUSH LEVER AND TRIGGER MUST MOVE

SMOOTHLY.

— 12 —

English

Nail Guide

Knob

Pull Trigger

Do not pull Trigger

Magazine

Cover

(2) Adjust the air pressure to 70 psi (4.9 bar 5 kgf/cm

Connect the air hose.

Do not load any nails in the Nailer.

䡺 THE NAILER MUST NOT LEAK AIR.

Hold the Nailer downward and pull the trigger.

䡺 THE NAILER MUST NOT OPERATE.

(3) With finger off the trigger, depress the push lever

against the workpiece.

䡺 THE NAILER MUST NOT OPERATE.

(4) Without touching the trigger, depress the push lever

against the workpiece.

Pull the trigger.

䡺 THE NAILER MUST OPERATE

(5) With the Nailer off the workpiece, pull the trigger.

Depress the push lever against the workpiece.

䡺 THE NAILER MUST OPERATE.

(6) If no abnormal operation is observed, you may load

nails in the Nailer.

Drive nails into the workpiece that is the same type to

be used in the actual application.

䡺 THE NAILER MUST OPERATE PROPERLY.

ADJUSTING AIR PRESSURE

WARNING

䢇 Do not exceed 120 psi (8.3 bar 8.5 kgf/cm

Adjust the air pressure at recommended operating

pressure 70 – 120 psi (4.9 – 8.3 bar 5 – 8.5 kgf/cm

)

according to the length of nails and the hardness of

workpiece.

The correct air pressure is the lowest pressure which will

do the job. Using the Nailer at a higher than required air

pressure unnecessarily over stresses the Nailer.

LOADING NAILS

WARNING

䢇 When loading nails into Nailer,

1) do not pull trigger;

2) do not depress push lever; and

3) keep Nailer pointed downward.

(1) Grip the nail guide and knob with your fingers. Press

the knob down and swing the nail guide open. Then

open the magazine cover.

(2) Adjust the position of the nail holder according to the

nail length.

The nail will not feed smoothly if the nail holder is not

correctly adjusted.

1 Turn the nail holder about 90 degrees

counterclockwise.

2 Move the nail holder up and down to align the

plate of the nail holder with a mark on the

magazine in accordance with the length of the

nails being used.

3 Turn the nail holder 90 degrees clockwise until

you hear "click".

Depress

Push Lever

— 13 —

English

For 1-1/2" (38 mm)

First Nail

Magazine

Magazine Opening

Nail

For 7/8", 1" and

1-1/4" (22 mm,

25 mm, 32 mm)

Plate

Driving Hole

First Nail

Nail Guide

Guide Slot

Pawl

Guide Surface

Feeder

Knob

Nail Guide

Magazine Cover

Nail Holder

Magazine Cover

Magazine Stopper

For 1-1/2" and 1-3/4"

For 1-1/4"

Mark

NOTE: Before loading nails in the magazine, adjust the

nail holder. If the magazine cover is forcibly

closed without adjusting the nail holder correctly,

the nail holder may be damaged.

(3) Place the nail coil in the magazine.

Insert the first nail into the magazine opening.

(4) Close the magazine cover.

(5) 1 Uncoil enough nails to reach the driving hole.

2 Insert the first nail into the driving hole and the

second nail between the two pawls of the feeder.

3 Fit the nail heads in the guide slot.

NOTE: Be careful not to deform the collated wires and

not to disengage the nails with the guide surface.

Otherwise, the nail guide will not close correctly.

4 Pulling the nails to the right

After checking and making sure that the magazine

cover is closed, hook your fingers on the nail

For 1-3/4" (45 mm)

Magazine guide and knob, turn the nail guide clockwise

while pressing the knob downward, and then

close the nail guide completely.

(6) Lock the knob completely.

The Nailer is now ready to operate.

<NV45AB2(S)>

(1) Press the magazine stopper and open the magazine

cover.

(2) Adjust the position of the nail holder according to the

nail length.

The nail will not feed smoothly if the nail holder is not

correctly adjusted.

1 Turn the nail holder about 90 degrees

counterclockwise.

2 Move the nail holder up and down to align the top

of the nail holder with a mark on the holder shaft

in accordance with the length of the nails being

used.

3 Turn the nail holder 90 degrees clockwise until

you hear "click".

NOTE: Before loading nails in the magazine, adjust the

nail holder. If the magazine cover is forcibly

closed without adjusting the nail holder correctly,

the nail holder may be damaged.

Nail Holder

Magazine Cover

For 7/8" and 1"

— 14 —

English

First Nail

Magazine

Magazine Opening

Nail Guide

Knob

Driving Hole

First Nail

Guide Slot

Guide Surface

(3) Place the nail coil in the magazine.

Insert the first nail into the magazine opening.

(4) Close the magazine cover.

(5) Grip the nail guide and knob with finger.

Press the knob down and swing the nail guide open.

(6) 1 Uncoil enough nails to reach the driving hole.

2 Insert the first nail into the driving hole and the

second nail between the two pawls of the feeder.

3 Fit the nail heads in the guide slot.

NOTE: Be careful not to deform the collated wires and

not to disengage the nails with the guide surface.

Otherwise, the nail guide will not close correctly.

4 Pulling the nails to the right, swing the nail guide

closed.

(7) Lock the knob completely.

The Nailer is now ready to operate.

NAILER OPERATION

Read section titled “SAFETY”(pages 4 – 7).

DANGER

䢇 Operators and others in

work area MUST wear

safety glasses with side

shields which conforms

to ANSI Z87.1

specifications.

WARNING

䢇 NEVER point tool at yourself or others in work area.

䢇 Keep fingers AWAY from trigger when not driving

nails to avoid accidental firing.

䢇 Choice of triggering method is important.

Please read and understand “METHODS OF

OPERATION” found below.

䢇 Never place your hands or feet closer than 8

inches (200 mm) from firing head when using.

䢇 Do not drive nails on top of other nails or with

Nailer at too steep of an angle; nails can ricochet

and hurt someone.

䢇 In order to avoid double fire or unwanted ejection

of a nail due to bouncing of the Nailer.

1) do not push Nailer on workpiece with strong

force;

2) take Nailer away from workpiece using recoil;

3) release trigger quickly when performing

trigger fire.

䢇 Do not drive nails into thin boards or near corners

and edges of workpiece. Nails can be driven

through or away from workpiece and hit

someone.

䢇 Never drive nails from both sides of a wall at the

same time. Nails can be driven into and through

the wall and hit a person on the opposite side.

䢇 Never use Nailer which is defective or operating

abnormally.

䢇 Do not use Nailer as hammer.

䢇 Disconnect air hose from Nailer when:

1) it is not in use;

2) leaving work area;

3) moving it to another location; and

4) handing it to another person.

Nails

Nail Guide

Feeder

Pawl

— 15 —

English

This Hitachi nailer has a STANDARD CONTACT TRIP

MECHANISM (Bounce Fire). An OPTIONAL SEQUENTIAL

TRIP MECHANISM kit (SINGLE SHOT) is available as order

part number 878226.

THE STANDARD CONTACT TRIP MECHANISM (Bounce

Fire) is for use where rapid fastener placement is desired

and must be operated in accordance with the following

“Methods of Operation”.

NOTE:

䢇 Be careful that the final nail can be dropped or driven

at an irregular angle.

METHODS OF OPERATION

This Nailer is equipped with the push lever and does not

operate unless the push lever is depressed (upward

position).

There are two methods of operation to drive nails with

this Nailer.

They are:

1. Intermittent operation (Trigger fire):

2. Continuous operation (Push lever fire):

(1) Intermittent operation (Trigger fire)

1 Position the nail outlet on the workpiece with

finger off the trigger.

2 Depress the push lever firmly until it is completely

depressed.

3 Pull the trigger to drive a nail.

4 Remove finger from the trigger.

To drive another nail, move the Nailer along the

workpiece and repeat this procedure.

(2) Continuous operation (Push lever fire)

1 Pull the trigger with the Nailer off the workpiece.

2 Depress the push lever against the workpiece to

drive a nail.

3 Move the Nailer along the workpiece with a

bouncing motion.

Each depression of the push lever will drive a nail.

As soon as the desired number of nails have been

driven, remove finger from the trigger.

WARNING

䢇 Keep your finger off the trigger except during

fastening operation, because serious injury could

result if the push lever accidentally contacts you

or others in work area.

䢇 Keep hands and body away from the discharge

area. The nailer with contact trip mechanism may

bounce from the recoil of driving a fastener and

unwanted subsequent fastener may be driven,

possibly causing injury.

䢇 Some types of loaded nails can spark out of the

muzzle during a nail driving operation. Exericise

caution!

THE OPTIONAL SEQUENTIAL TRIP MECHANISM (SINGLE

SHOT PARTS) is for use where precision fastener

placement is desired and must be operated in accordance

with the following “Method of Operation”.

You must first depress the push lever (upward

position) where you wnat to drive a nail and then pull

the trigger. After the each nail is driven, completely

release the trigger and lift the tool off the work

surface.

An OPTIONAL SEQUENTIAL TRIP MECHANISM may

reduce the possibility of bodily injury to you or others

in the work area. This is because it is less likely to

drive an unwanted nail if you keep the trigger pulled

and accidentally bump the push lever against yourself

or others. An OPTIONAL SEQUENTIAL TRIP

MECHANISM may also reduce the speed of operation

compared to the standard contact trip mechanism.

NOTE:

䢇 Both STANDARD CONTACT TRIP MECHANISM and

OPTIONAL SEQUENTIAL TRIP MECHANISM are safe if

used as described above and accroding to all

warnings and instructions.

䢇 Always handle nails and package carefully.

If nails are dropped, collating wire may be damaged

and cut, which will cause mis-feeding and jamming.

䢇 After nailing:

1) disconnect air hose from the Nailer;

2) remove all nails from the Nailer;

3) supply 5 – 10 drops of Hitachi pneumatic tool

lubricant into the air plug on the Nailer; and

4) open the petcock on the air compressor tank to

drain any moisture.

Previously pull

the trigger

Push Lever

Trigger

— 16 —

English

Too Deep Flush

Turn Adjuster

Too Shallow Flush

Turn Adjuster

Adjuster

Disconnect air hose

Second Row

First Row

Outlet

Proper Shingle

Exposure

Disconnect

air hose

Hex. Socket

Hd. Bolt

USING THE SHINGLE GUIDE

The shingle guide can be used to control shingle spacing.

Adjust the shingle guide in the following order.

1 DISCONNECT AIR HOSE FROM NAILER

2 Loosen the hex. socket hd. bolt with the accessory

Allen wrench.

3 Place the shingle guide against the bottom of the first

row of shingles.

4 Adjust the distance between the outlet and the shingle

guide to the proper shingle exposure by sliding the

shingle guide.

5 Tighten the hex. socket hd. bolt.

NOTE:

䢇 The proper shingle exposure will depend on the type

of shingle and the manufacturer's specifications.

䢇 The shingle guide is not to be utilized as an indicator

of nail location.

ADJUSTING THE NAILING DEPTH

To assure that each nail penetrates to the same depth, be

sure that:

1) the air pressure to the Nailer remains constant

(regulator is installed and working properly), and

2) the Nailer is always held firmly against the workpiece.

If nails are driven too deep or shallow into the workpiece,

adjust the nailing in the following order.

1 DISCONNECT AIR HOSE FROM NAILER

2 If nails are driven too deep, turn the adjuster

counterclockwise while pulling it downward.

When the adjuster is released, it returns upward.

Furthermore, turn the adjuster until it reaches a

position where it gets fixed with a clock.

If nails are driven too shallow, turn the adjuster

clockwise while pulling it downward.

When the adjuster is released, it return upward.

Furthermore, turn the adjuster until it reaches a

position where it gets fixed with a clock.

The adjuster can be fiexed each at 1/4 rotation.

The adjuster moves approximately 0.25mm per 1/4

rotation.

3 Stop turning the adjuster when a suitable position is

reached for a nailing test.

4 Connect the air hose.

ALWAYS WEAR EYE PROTECTION.

Perform a nailing test.

5 DISCONNECT AIR HOSE FROM NAILER.

6 Choose a suitable position for the adjuster.

Shingle Guide

— 17 —

English

MAINTENANCE

NOTE: The information contained in this Manual is designed to assist you in the safe maintenance of the Nailer.

Some illustrations in this Manual may show details or attachments that differ from those on your own Nailer.

MAINTENANCE AND INSPECTION

Read section titled “SAFETY” (pages 4 – 7).

WARNING

䢇 Disconnect air hose and remove all nails from

Nailer when:

1) doing maintenance and inspection; and

2) clearing a jam.

䢇 Never use gasoline or other highly flammable

liquides for cleaning.

1. Clearing a jam

Remove a jammed nail in the following order :

1 DISCONNECT AIR HOSE.

2 Open the nail guide.

3 Insert a rod into the outlet.

Tap the rod with a hammer.

4 Remove the jammed nail with a slotted screw

driver.

5 Cut the deformed collated wire with nippers.

Correct the deformation.

6 In case of frequent jam, contact a Hitachi

authorized service center.

Hammer

Rod

Outlet

Disconnect

air hose

Nail

Slotted Screw Driver

2. Inspecting the feeders

1 DISCONNECT AIR HOSE.

2 Clean the knob sliding part.

Lubricate it with Hitachi pneumatic tool lubricant.

3 Open the nail guide and remove dust.

Lubricate the nose opening and feeder shaft.

CAUTION

䢇 Check that the main nail stopper and sub nail stopper

slide smoothly by pushing them with finger.

If not smooth, nails can be driven at an irregular angle

and hurt someone.

4 Lubricate the feeding surfaces of the nose and the

nail guide after cleaning.

This promotes smooth operation and prevents

rust.

Nail Guide

Knob

Disconnect

air hose

Nail Guide

Sub Nail Stopper

Feeder Shaft

Feeder

Nose Opening

Main Nail Stopper

— 18 —

English

3. Cleaning and removal of tar and dirt

Tar and dirt may build up on the nose and push lever.

This can prevent correct operation.

Clean and remove tar and dirt with kerosene, #2 fuel

oil or diesel fuel.

NEVER USE GASOLINE or other highly flammable

liquids.

Vapor of such liquids inside the Nailer could be

ignited by a spark produced during nailing, which can

cause an explosion.

1 Immerse only the area around the outlet in

solvent.

Do not immerse the magazine or body.

Plastic parts and O-ring may be damaged.

2 Dry off the Nailer before use. Any oil film left after

cleanup will accelerate the tar buildup, and the

Nailer will requite more frequent re-cleaning.

3 Make sure the push lever operates properly.

WARNING

䢇 Never use Nailer unless push lever is operating

properly.

NOTE:

䢇 Solvents sprayed on nose to clean and free up the

push lever may have the opposite effect. The solvent

may soften the tar on the shingles and cause tar

buildup to be accelerated. Dry operation is better.

4. Inspecting the magazine

1 DISCONNECT AIR HOSE.

2 Clean the magazine. Remove dust or wooden tips

which may have accumulated in the magazine.

5. Storing

䡬 When not in use for an extended period, apply a thin

coat of the lubricant to the steel parts to avoid rust.

䡬 Do not store the Nailer in a cold weather environment.

Keep the Nailer in a warm area.

䡬 When not in use, the Nailer should be stored in a

warm and dry place.

Keep out of reach children.

Body

Push

Lever

Outlet

Magazine

Nose

Warning Label

6. WARNING LABEL

Change the WARNING LABEL if missing or damaged.

A new WARNING LABEL is available from a Hitachi

authorized service center.

7. Maintenance chart (See page 19)

8. Operator troubleshooting (See page 19)

9. Service parts list

A: Item No.

B: Code No.

C: No. Used

D: Remarks

CAUTION

䢇 Repair, modification and inspection of Hitachi Power

Tools must be carried out by an Hitachi Authorized

Service Center.

This Parts List will be helpful if presented with the

tool to the Hitachi Authorized Service Center when

requesting repair or other maintenance. In the

operation and maintenance of power tools, the safety

regulations and standards prescribed in each country

must be observed.

MODIFICATIONS:

Hitachi Power Tools are constantly being improved and

modified to incorporate the latest technological

advancements.

Accordingly, some parts (i.e. code numbers and/or design)

may be changed without prior notice.

SERVICE AND REPAIRS

WARNING

䢇 Only service personnel trained by Hitachi,

distributor or employer shall repair the Nailer.

䢇 Use only parts supplied or recommended by

Hitachi for repair.

All quality Nailers will eventually require servicing or

replacement of parts because of wear from normal use.

NOTE: Specifications are subject to change without any

obligation on the part of HITACHI.

— 19 —

English

Maintenance chart

ACTION WHY HOW

Drain air line filter daily. Prevent accumulation of moisture Open manual petcock.

and dirt.

Keep lubricator filled. Keep the Nailer lubricated. Fill with Hitachi pneumatic tool

lubricant.

Clean filter element — then blow Prevent clogging of filter with dirt. Follow manufacturer’s instructions.

air through filter in direction

opposite to normal flow.

Clean magazine and feeder Prevent a jam. Blow clean daily.

mechanism.

Keep push lever working properly. Promote operator safety and Blow clean daily.

efficient Nailer operation.

Lubricate the Nailer after nailing. Extend the Nailer life. Supply 5 – 10 drops of lubricant into

the Nailer.

Drain air compressor. Keep the Nailer operated properly. Open petcock on air compressor tank.

PROBLEM

Nailer operates, but no nail is driven.

Operator troubleshooting

Most minor problems can be resolved quickly and easily using the table below.

If problems persist, contact a Hitachi authorized service center for assistance.

CHECK METHOD CORRECTION

Open nail guide. Check for a jam. Clear a jam per page 17.

Check function of feeder per Clean and lubricate.

page 17.

Check for proper nails. Use only recommended nails.

Check air pressure. Increase air pressure. (Do not

exceed 120 psi (8.3 bar 8.5 kgf/cm

))

Check position of adjuster per page 16. Readjust.

——— Use Hitachi pneumatic tool lubricant.

Driver blade worn?

Contact Hitachi for replacement.

Piston O-ring worn or damaged?

Check air pressure. Reduce air pressure.

(Adjust 70 – 120 psi

(4.9 – 8.3 bar 5 – 8.5 kgf/cm

))

Check position of adjuster per page 16. Readjust.

Check for proper nails. Use only recommended nails.

Check function of nail feeder per Clean and lubricate.

page 17.

——— Use Hitachi pneumatic tool lubricant.

Check position of nail holder in Adjust nail holder to proper position.

magazine per page 12 or 13.

Piston O-ring cut or heavily worn? Contact Hitachi for replacement.

Check for proper nails. Use only recommended nails.

Driver blade worn? Contact Hitachi for replacement.

Check inside diameter of air hose. Use larger air hose.

Weak drive.

Slow to cycle.

Drives too deep.

Skipping nails. Intermittent feed.

Nails jam.

Driven nail is bent.

Drives properly during normal

operation, but does not drive fully

at faster nailing speeds.

— 20 —

Français

INFORMATION IMPORTANTE

Lire et bien assimiler toutes les étiquettes de l’outil ainsi que toutes les instructions de

fonctionnement, les consignes de sécurité et les avertissements de ce mode d’emploi

avant d’utiliser ou d’entretenir ce cloueur.

Le non respect des avertissements pourrait entraîner la MORT ou des BLESSURES

GRAVES.

La plupart des accidents résultant de l’utilisation ou de l’entretien des cloueurs sont dus au non respect de

certaines consignes et précautions de sécurité élémentaires. Un accident peut souvent être évité en

reconnaissant une situation potentiellement dangereuse avant qu’elle ne se produise, et en respectant les

procédures de sécurité applicables.

Les consignes de sécurité élémentaires sont données dans la section “SECURITE” du manuel et dans les

sections relatives aux instructions d’utilisation et d’entretien.

Les dangers à éviter pour empêcher tout risque de blessures ou de dommage de l’outil sont identifiés par les

mots DANGER et AVERTISSEMENT, sur le cloueur et dans ce manuel.

Ne jamais utiliser ce cloueur pour des applications autres que celles qui sont spécifiées dans ce manuel.

DEFINITION DES MOTS DE SIGNALISATION

DANGER indique une situation imminente dangereuse qui, si elle n’est pas évitée, entraînera la mort ou des blessures

graves.

AVERTISSEMENT indique une situation potentiellement dangereuse qui, si elle n’est pas évitée, risque d’entraîner la

mort ou des blessures graves.

ATTENTION indique une situation potentiellement dangereuse qui, si elle n’est pas évitée, risque d’entraîner des

blessures légères ou modérées, ou d’endommager l’outil.

REMARQUE met en relief les informations essentielles.

La page charge ...

Hitachi NV 45AB2(S) Manuel utilisateur

Marque: Hitachi

Modèle: NV 45AB2(S)

Catégorie: Cloueuse

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Hitachi NV 45AB2(S) User manual
español: Hitachi NV 45AB2(S) Manual de usuario

Hitachi NV 45AB2(S) Manuel utilisateur

Hitachi NV 45AB2(S) Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents