Denver MRD-51 Manuel utilisateur

USER MANUAL

MRD-51

WWW.DENVER-ELECTRONICS.COM

Please read this user manual carefully before start using the product.

CLEANING THE CABINET

If the wooden cabinet becomes dusty please wipe it with a soft, non-abrasive dust cloth. Also

don’t use water or spray cleaners as this can damage the cabinet and the plastic/metal parts

of the unit.

TECHNICAL SPECIFICATION

 Turntable speed: 33/45/78 RPM (Disc size 17.5/25/30cm)



 CD can play CD/CD-R/CD-RW/MP3

 USB can play MP3

 Cassette: C60 & C90 (C120 cassette is not recommended)

 Output power: 2x4W

PREPARATION FOR USE

IMPORTANT: RAISING AN LOWERING THE TURNTABLE LID

To open the lid. Raise it as far as it can go until the lid support bracket locks in the position.

To close the lid. Pull forward the lid support bracket to release and then gently lower the lid.

TO AVOID DAMAGING THE CABINET OR THE LID, NEVER FORCE THE LID CLOSED. ALWAYS RAISE THE LID

TO RELEASE THE LID SUPPORT BRACKET.



LOCATIIONS OF CONTROLS AND INDICATORS

2

LOCATION OF CONTROLS

1. DUST COVER

2. COVER MECHANISM

3. TURNTABLE

4. SPEAKERS

5. TAPE STOP/EJECT BUTTON

6. CASSETTE MECHANISM

7. USB SOCKET

8. AUX-IN

9. 3.5mm HEADPHONE JACK

10. FUNCTION BUTTON (DAB/FM/CD/USB/PHONO/TAPE/AUX)

11. REMOTE SENSOR

12. CD DOOR

13. PLAR/PAUSE

14. STOP BUTTON

15. DN/F-R

16. UP/F-F

17. REC/DEL (RECORD BUTTON/DELETE BUTTON)

18. CD DOOR OPEN/CLOSE BUTTON

19. VOLUME KNOB/ POWER STANBY

20. POWER LED

21. DAB MENU BUTTON

22. DAB INFO BUTTON

23. DAB SCAN BUTTON

24. DAB PRESET BUTTON

25. DAB ENTER

26. LCM DISPLAY

27. TUNING BOTTON/PLAY.MODE

28. FM/DAB ANTENNA

29. AC CORD

30. ON/OFF SWITCH

31. ADAPTOR

32. TURNTABLE PAUSE SWITCH

33. PICK-UP HOLDER

34. Auto-stop ON/OFF

35. 33/45/78 RPM SPEED SELECTOR

36. TONE ARM

37. TURNTABLE

38. LINE OUT

REMOTE CONTROL

1. POWER ON/OFF

2. CD DOOR OPEN/CLOSE BUTTON

3. RECORD BUTTON

4. DELETE BUTTON5. MODE BUTTON

6. STOP BUTTON

7. REPEAT BUTTON/VOL+

8. PROGRAM BUTTON/VOL-

9. PLAY/PAUSE BUTTON

10. DAB SCAN BUTTON

11. INFO

12. SKIP-BUTTON/FAST FORWARD BUTTON

13. SKIP+ BUTTON/REWIND BUTTON

14. NUMERIC KEYBOARD

15. +10

16. ENTER

17. MENU

18. EQ

19. PRESET

20. TIMER

REMOTE BATTERY INSTALLATION

The infrared remote control requires 2 PCS UM-4 R03, AAA (3V) Battery

POWER ON/OFF

1. Press POWER to turn the system on. The power indicator lights up.

2. Press the function selector buttons (DAB/FM/CD/USB/TAPE/PHONO/AUX IN) to select the desired

function.

3. Start to adjust the volume by using the volume control button.

4. When finished listening press POWER again to turn off the system. The power indicator goes off.

Remark: The unit is comply with ERP2, the unit will turn to Standby mode if there is no operation on the

unit after 15 mins, please press POWER button 2 times if you want to re-start the unit.

DAB MODE

Press function button (10) (5 on remote) repeatedly to select DAB mode. Press SKIP+/- (16/15) (12/13 on

remote) to search the program

DAB MENU

Press MENU (21) (17 on remote) to access to the options.

1. Full Scan: select this option to perform a full scan of the available DAB programs. You can press SCAN (23)

to perform the same action.

2. Manual Tune: select this option to select manually the DAB frequency

3. DRC: select this option to choose between DRC low, DRC high and DRC off.

4. Prune: select this option to choose between PRUNE stations on or off.

DAB PRESET

You can program a maximum of 20 preset radio stations.

1. Press and hold PRESET (24) (19 on remote). PRESET STORE will appear on display. Press SKIP+/- (16/15)

(12/13 on remote) to select the preset number. Press ENTER (9) (16 on remote) to confirm.

2. Press PRESET (24) (19 on remote) to navigate through the presets.

DAB INFO

Repeatedly press INFO (22) (18 on remote) to see the following information: NAME/KBPS/DATE /TIME.

FM MODE

Press function button (10) (5 on remote) repeatedly to select FM mode. Turn the TUNING KNOB (27) to

manually select the frequency

FM MENU

Press MENU (21) (17 on remote) to access to the options.

1. Scan Setting: select this option to choose between scanning all stations or only the strong stations.

2. Audio Setting: select this option to choose between forcing mono audio or allowing stereo Sound.

FM PRESET

See DAB PRESET instructions.

FM INFO

Repeatedly press INFO (22) (18 on remote) to see the following informations: KIND OF PRO-

GRAM/FREQUENCE/AUDIO/DATE/TIME.

CD OPERATION

1. Press the CD/USB button to enter CD mode, the “---“ and ‘DISC’ icon will be shown on the screen. The unit

can play CD, CD-R and CD-RW.

2. Press the OP/CL button top open the CD drawer.

3. Place your disc in the CD drawer with the label side facing up.

4. Press the OP/CL button again to close the CD drawer. Playback will automatically start from the first track.

5. MP3 icon will be shown if MP3 file is detected in the disc.

PLAYING CASSETTE

Note: Before inserting the tape in the player be sure that there is no excess slack in the cassette that could

jam the mechanism.

1. Press POWER to turn the system on.

2. Press TAPE button to enter TAPE mode.



3. Insert your cassette into the slot located on the right side of the cabinet, as shown in the illustration, with

the side you wish to play facing up and the open end on the right side.

4. Cassette playback begins as soon as the tape is inserted. Adjust the VOLUME control to the desired level.

5. To advance the tape rapidly, depress the button approximately half way. The tape will move forward

rapidly as long as the button is depressed. Normal playback will resume when the button is released

6. When the tape ends, the player stops automatically. Depress the button completely to remove the

tape from the player. You may depress button to stop playing the tape at any time.

7. Press POWER again to turn the system off.

PLAYING VINYLS RECORDS

The system includes a full-size, 3 speed, belt-drive turntable. You can play 33, 45 and 78rpm records.

1. Press POWER to turn the system on.

2. Press the PHONO button to enter the PHONO mode.

3. Make sure you have removed the stylus cover from the stylus and have released the tone arm lock

that

4. secured the tone arm to the tone arm rest.

5. Set the turntable speed selector to appropriate speed 33, 45 or 78rpm. If you are playing 45 rpm

singles, place the 45rpm adapter on the centre spindle.

6. Place your record on the the centre spindle.

7. Raise the cue lever to lift the tone arm of its rest. Move the tone arm to the edge of the record. The

turntable starts automatically. Use the cue lever to gently lower the tone arm onto the record.

8. Adjust the volume control to the desired level.

9. Press POWER again to turn the system off. The POWER indicator goes OFF.



Note: Do not turn or stop the turntable manually. Moving or jarring the turntable without securing the

tone arm clamp could result in damage to the tone arm.

AUX IN OPERATION

Connect the audio system into the AUX IN jack on the rear panel, Press the PHONO/AUX IN button. Start

playing from the connected device.

USB OPERATION

1. Press the CD/USB button first and the FUNCTION button to enter USB mode. The ‘---‘ and USB icon will

be shown.

2. Insert a USB flash device into the USB socket.

3. PLAY/PAUSE, DN/UP and stop functions are the same as CD functions.

Note: You may press the FUNCTION on the panel or long press PLAY/PAUSE button on the remote control

for 2 seconds to change the playing mode between CD and USB.

PLAYING IN MP3 MODE (CD/USB)

1. Press PLAY/PAUSE button to start or pause playback selected track.

2. While playing the song, the song number and folder number of the selected track will be shown in

the display.

3. You can stop the playback at any time by pressing the STOP button.

TRACK SKIP AND HIGH SPEED TRACK SEARCH IN CD/USB MODE

During CD/USB playback press UP/F.F ( ) or DN/F.R ( ) button on the unit front panel or on the

remote control repeatedly to change track. To rapidly search forward or backwards within a track press

and hold UP/F.F (press UP/F.F ( ) or DN/F.R ( ) button. To skip 10 tracks back or forth then

press TRACK-10 or TRACK+10 on the remote control.

USB RECORDING

1. CD recording

Insert USB flash drive into the USB socket. Then press CD/USB button. Place CD into the CD drawer and

play the track which will be recorded. Press RECORD button twice to start recording. If all CD is played,

Then all tracks will be recorded. NOTE: Recording will fail if pressing STOP button during recording



2. MP3 DISC recording

Insert USB flash drive into the USB socket. Then press CD/USB button. Place CD with MP3 files into the CD

drawer and play the MP3 track which will be recorded. Press RECORD button twice to start recording. If all

MP3 files is played, Then all tracks will be recorded. NOTE: Recording will fail if pressing STOP button

during recording

3. Cassette recording

Insert USB flash drive into the USB socket. Then press TAPE button. Place the cassette into the socket. Play

cassette. Press RECORD button twice to start recording. Press STOP button to stop recording.

4. Vinyl recording

Insert USB flash drive into the USB socket. Then press PHONO/AUX IN button. Play the vinyl and press

RECORD button twice to start recording. Press STOP button to stop recording.

5. AUX IN recording

Insert USB flash drive into the USB socket. Connect the external audio device into the AUX jack on the rear

panel. Then press PHONO/AUX IN button and play audio and press RECORD button twice to start

recording.



DELETE TRACKS FROM USB DISC

Press CD/USB button on the front panel or long press PLAY/PAUSE on remote control to select USB

mode. Select the track and press delete for 2 seconds and the track is deleted.

CLOCK

In standby mode, long press STOP button to display 24H flashing, then short press DN/F-R, UP/F-F key to

select 12/24H, then short press ST0P button to set MINUTE/HOUR/DAY/MONTH/YEAR.

TIMER

Long press TIMER button under Standby mode to choose Alarm or Clock function, then short press the

remote control up and down buttons to enter the alarm debugging, press TIMER reset after complete the

alarm debugging, and then press the remote control up and down buttons to select DAB, FM , CD,TAPE,

USB, boot mode.

SLEEP

Setting the clock to CD,DAB, FM, TAPE, AUX, USB or PHONO mode first, in CD,DAB, FM, TAPE, AUX, USB,

PH0N0 mode, long press TIMER to display Sleep, Timer, 0FF and then press the up and down buttons on

the remote control to select the sleep time: 15, 30, 45, 60 , 90 min then automatic shutdown.



Electric and electronic equipment is marked with the crossed out trash can symbol, seen below. This symb

ol signifies that electric and electronic equipment should not be disposed of with other household waste,

but should be disposed of separately.

All cities have established collection points, where electric and electronic equipment can either be

submitted free of charge at recycling stations and other collection sites, or be collected from the

households. Additional information is available at the technical department of your city.Hereby, Inter Sales

A/S declares that the radio equipment type MRD-51 is in compliance with Directive 2014/53/EU. The full

text of the EU declaration of conformity is available at the following internet address:

Please enter: www.denver-electronics.com and then click the search ICON on top line of website.

Write model number: MRD-51

Now enter product page, and red directive is found under downloads/other downloads

Operating Frequency Range: FM:87.5-108MHz DAB:168-240MHz

Max Output Power: 2*2.5W

DENVER ELECTRONICS A/S

Omega 5A, Soeften

DK-8382 Hinnerup

Denmark

Facebook.com/denverelectronics

Electric and electronic equipment contains materials, components and substances that can be hazardous to

your health and the environment, if the waste material (discarded electric and electronic equipment) is not

handled correctly.

BRUKSANVISNING

MRD-51

WWW.DENVER-ELECTRONICS.COM

Läs denna användarmanual noggrant, innan du börjar använda produkten.

FÖ RSIKTIGHET

FÖ R ATT UNDVIKA BRAND ELLER STÖ TAR, ANVÄND INTE DENNA APPARAT MED EN

FÖ RLÄNGNINGSSLADD ELLER ANNAT UTTAG OM INTE BLADEN HELT KAN FÖ RAS IN FÖ R ATT

UNDVIKA EXPONERING. FÖ R ATT FÖ REBYGGA RISK FÖ R BRAND ELLER ELSTÖ TAR SKALL MAN INTE

UTSÄTTA DENNA ENHET FÖ R REGN ELLER FUKT.

Blixten med pilhuvudet i en

liksidig triangel är avsedd att

varna användaren för

närvaron av oisolerad ”farlig

spänning” innanför

produktens hölje som kan

vara tillräckligt stark för att

utgöra en risk för elektriska

stötar.

VARNING: FÖ R ATT MINSKA

RISKEN FÖ R ELEKTRISK

KORTSLUTNING SKA DU INTE TA

BORT LUCKAN (ELLER

BAKSIDAN). DET FINNS INGA

DELAR SOM KAN UNDERHÅLLAS

AV ANVÄNDAREN INVÄNDIGT.

Ö VERLÅT SERVICE ÅT BEHÖ RIG

SERVICEPERSONAL.

Utropstecknet i en liksidig

triangel är avsedd att varna

användaren för att det finns

viktiga instruktioner för drift

och underhåll (service) i den

dokumentation som medföljer

apparaten.

VIKTIGA SÄKERHETSANVISNINGAR

1. Läs, följ och förvara anvisningarna i denna manual.

2. Rengör endast med torr trasa.

3. Blockera inte några ventilationsöppningar. Installera i enlighet med tillverkarens anvisningar.

4. Installera inte nära värmekällor såsom radiatorer, värmeelement, kaminer eller annan

utrustning (inkl. förstärkare) som avger värme.

5. Skydda sladden från att gå på eller klämmas speciellt vid kontakten, eluttag och utgången från

apparaten.

6. Koppla ur denna apparat under åskväder eller när den inte används under långa perioder.

7. Ö verlämna all service till en kvalificerad tekniker. Service krävs när apparaten har skadats på

något sätt, om till exempel nätsladden eller kontakten är skadad, vätska har spillts eller

föremål har fallit in i apparaten, om apparaten har utsatts för regn eller fukt, inte fungerar

normalt, eller har tappats.

8. Enheten ska inte utsättas för droppande eller stänkande vatten och inga föremål med vätska

som vasar ska placeras på apparaten.

9. Ö verbelasta inte vägguttaget.

10. Använd kontroller och omkopplare så som beskrivs i manualen.

11. Förvara dina CD-skivor, kassetter i ett svalt utrymme för att undvika skador från värmekällor.

12. När du flyttar på enheten, måste du först koppla ur nätkabeln.

FÖ RSIKTIGHET

RISK FÖ R ELEKTRISK STÖ T

Ö PPNA INTE



RENGÖ RING AV SKÅPET

Om träskåpet samlar på sig damm, ska du torka det med en mjuk, icke-slipande dammtrasa. Du

ska heller inte använda vatten eller sprayrengöringsmedel, eftersom detta kan skada skåpet och

plast-/metalldelarna på enheten.

TEKNISK SPECIFIKATION

 Skivspelarens hastighet: 33/45/78 RPM (Skivstorlek 17,5/25/30cm)

 CD kan spela upp CD/CD-R/CD-RW/MP3

 USB kan spela upp MP3

 Kassett: C60 och C90 (C120 kassett rekommenderas inte)

 Utgående ström: 2x4W

FÖ RBEREDELSE FÖ R ANVÄNDNING

 Ta försiktigt bort enheten från kartongen och plocka bort allt

förpackningsmaterial från enheten.

 Linda upp nätsladden och sträck ut den till sin fulla längd.

 Linda upp FM-antennkabeln och sträck ut den till sin fulla

längd.

 Lyft upp locket till för att visa skivtallriken.

 Ta bort det ogenomskinliga vita plastomslaget från

grammofonnålen genom att skjuta den i pilens riktning.

 Var uppmärksam på grammofonnålen under spelning,

eftersom skada på grammofonnålen täcks inte av garantin.

 Ta bort ståltråden som användes för att säkra pickuparmen

under transporten.

 Lås upp för pickuparmen .

 Anslut nätkontakten till AC 220V, 50HZ uttag.

VIKTIGT: HÖ JA OCH SÄNKA LOCKET PÅ SKIVTALLRIKEN

Pickuparmens

låsarm

Grammofonnålens

skydd



När du vill öppna locket: Ta upp det så långt det går till dess att locket får stöd av vinkeljärnets lås i

läge.

När du vill stänga locket: Dra locket framåt för att vinkelstödet ska släppa och sedan sänk locket

försiktigt.

FÖ R ATT UNDVIKA ATT SKADA SKÅPET ELLER LOCKET, ANVÄND ALDRIG VÅLD FÖ R ATT STÄNGA

LOCKET. LYFT ALLTID UPP LOCKET FÖ R ATT LOCKETS VINKELSTÖ D SKA SLÄPPA.

PLATSER FÖ R KONTROLLER OCH INDIKATORER

2

KONTROLLERNAS PLACERING

1. DAMMLUCKA

2. LUCKANS MEKANISM

3. SKIVTALLRIK

4. HÖ GTALARE

5. KNAPPPEN STOPP/UTMATNING AV KASSETTBAND

6. KASEETBANDETS MEKANISM

7. USB-KONTAKT

8. AUX-IN

9. 3,5 mm HÖ RLURSUTTAG

10. FUNKTIONSKNAPP (DAB/FM/CD/USB/PHONO/BAND/AUX)

11. FJÄRRSENSOR

FRONTPANEL

SKIVTALLRIK

VISNING BAKIFRÅN

12. CD-LUCKA

13. SPELA/PAUSA

14. STOPP-KNAPP

15. DN/F-R

16. UP/F-F

17. INSPELN/RAD (KNAPPEN INSPELNING/KNAPPEN RADERA)

18. Ö PPNA/STÄNG-KNAPPEN FÖ R CD-LUCKA

19. VOLYMRATT/ STRÖ M I STANDBY-LÄGE

20. LYSDIODSTRÖ M

21. KNAPPEN DAB-MENY

22. KNAPPEN DAB-INFO

23. KNAPPEN DAB-SCAN

24. KNAPPEN DAB-PRESET

25. DAB ENTER

26. LCM-SKÄRM

27. INSTÄLLNINGSKNAPP/SPELLÄGE

28. FM/DAB-ANTENN

29. AC-KABEL

30. PÅ/AV-KNAPP

31. ADAPTER

32. PAUSKNAPP FÖ R SKIVTALLRIK

33. NÅLMIKROFONENS HÅLLARE

34. Autostopp PÅ/AV

35. VARVTALSVÄLJARE 33/45/78 RPM

36. TONARM

37. SKIVTALLRIK

38. LINJE UT

La page charge ...

Denver MRD-51 Manuel utilisateur

Ce manuel convient également à

Denver MRD-51 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents