TEAC PD-501HR Le manuel du propriétaire

Marque: TEAC

Modèle: PD-501HR

Catégorie: Lecteurs DVD

Taper: Le manuel du propriétaire

D01179820B

PD-501HR

CD Player

OWNER’S MANUAL

MODE D’EMPLOI

MANUAL DEL USUARIO

IMPORTANT SAFETY PRECAUTIONS

CAUTION

DO NOT REMOVE THE EXTERNAL CASES OR CABINETS TO

EXPOSE THE ELECTRONICS. NO USER SERVICEABLE PARTS

ARE INSIDE.

IF YOU ARE EXPERIENCING PROBLEMS WITH THIS PRODUCT,

CONTACT TEAC FOR A SERVICE REFERRAL. DO NOT USE THE

PRODUCT UNTIL IT HAS BEEN REPAIRED.

USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF

PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY

RESULT IN HAZARDOUS RADIATION EXPOSURE.

WARNING: TO PREVENT FIRE OR SHOCK HAZARD,

DO NOT EXPOSE THIS APPLIANCE TO RAIN OR

MOISTURE.

IN USA/CANADA, USE ONLY ON 120 V SUPPLY.

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT

REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS

INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an

equilateral triangle, is intended to alert the user to the

presence of uninsulated “dangerous voltage” within the

product’s enclosure that may be of sufficient magnitude to

constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is

intended to alert the user to the presence of important

operating and maintenance (servicing) instructions in the

literature accompanying the appliance.

For Canada

Industry Canada’s Compliance Statement:

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe B est conforme à la norme

NMB-003 du Canada.

For U.S.A.

This equipment complies with Part 15 of FCC Rules. Operation is

subject to the following two conditions: 1) This device may not

cause interference and 2) This device must accept any interference,

including interference that may cause undesired operation of the

device.

Information to the user:

This equipment has been tested and found to comply with the

limits for a Class B digital device, pursuant to Part 15 of the FCC

Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equip-

ment generates, uses, and can radiate radio frequency energy and,

if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. However,

there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to

radio or television reception, which can be determined by turning

the equipment off and on, the user is encouraged to try to correct

the interference by one or more of the following measures:

• Reorient or relocate the equipment and/or the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for

help.

CAUTION

Changes or modifications to this equipment not expressly approved

by TEAC CORPORATION for compliance will void the user’s warranty.

“DSD” is a registered trademark.

Other company names and product names in this document are the trademarks or registered trademarks of their respective owners.

IMPORTANT SAFETY INSTRUCTIONS

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with dry cloth.

7) Do not block any ventilation openings. Install in accordance with

the manufacturer's instructions.

Do not install near any heat sources such as radiators, heat registers,

stoves, or other apparatus (including amplifiers) that produce heat.

9) Do not defeat the safety purpose of the polarized or grounding-

type plug. A polarized plug has two blades with one wider than

the other. A grounding type plug has two blades and a third

grounding prong. The wide blade or the third prong are provided

for your safety. If the provided plug does not fit into your outlet,

consult an electrician for replacement of the obsolete outlet.

10) Protect the power cord from being walked on or pinched

particularly at plugs, convenience receptacles, and the point

where they exit from the apparatus.

11) Only use attachments/accessories specified by the manufacturer.

12) Use only with the cart, stand, tripod, bracket, or

table specified by the manufacturer, or sold with

the apparatus. When a cart is used, use caution

when moving the cart/apparatus combination

to avoid injury from tip-over.

13) Unplug this apparatus during lightning storms or

when unused for long periods of time.

14) Refer all servicing to qualified service personnel. Servicing is

required when the apparatus has been damaged in any way, such

as power-supply cord or plug is damaged, liquid has been spilled

or objects have fallen into the apparatus, the apparatus has been

exposed to rain or moisture, does not operate normally, or has

been dropped.

The apparatus draws nominal non-operating power from the AC

outlet with its POWER or STANDBY/ON switch not in the ON position.

The mains plug is used as the disconnect device, the disconnect

device shall remain readily operable.

Caution should be taken when using earphones or headphones

with the product because excessive sound pressure (volume) from

earphones or headphones can cause hearing loss.

Do not expose this apparatus to drips or splashes.

Do not place any objects filled with liquids, such as vases, on

the apparatus.

Do not install this apparatus in a confined space such as a book

case or similar unit.

The apparatus should be located close enough to the AC outlet

so that you can easily reach the power cord plug at any time.

If the product uses batteries (including a battery pack or

installed batteries), they should not be exposed to sunshine, fire

or excessive heat.

CAUTION for products that use replaceable lithium batteries: there

is danger of explosion if a battery is replaced with an incorrect

type of battery. Replace only with the same or equivalent type.

Products with Class construction are equipped with a power sup-

ply cord that has a grounding plug. The cord of such a product

must be plugged into an AC outlet that has a protective ground-

ing connection.

CAUTION

WARNING

Precautions concerning batteries

Misuse of batteries could cause them to rupture or leak leading

to fire, injury or the staining of nearby things. Please read and

observe the following precautions carefully.

o Be sure to insert the batteries with correct positive (+) and

negative (_) orientations.

o Use batteries of the same type. Never use different types of bat-

teries together.

o If the remote control is not used for a long time (more than a

month), remove the batteries to prevent them from leaking.

o If the batteries leak, wipe away the leakage inside the battery

compartment and replace the batteries with new ones.

o Do not use batteries of types other than those specified. Do not

mix new batteries with old ones or use different types of batter-

ies together.

o Do not heat or disassemble batteries. Never throw batteries into

fire or water.

o Do not carry or store batteries with other metallic objects. The

batteries could short circuit, leak or explode.

o Never recharge a battery unless it is confirmed to be a recharge-

able type.

This product has been designed and manufactured according to FDA

regulations “title 21, CFR, chapter 1, subchapter J, based on the

Radiation Control for Health and Safety Act of 1968”, and is classified as

class

laser product. There is not hazardous invisible laser radiation

during operation because invisible laser radiation emitted inside of

this product is completely confined in the protective housings.

The label required in this regulation is as follows:

&(57,),&$7,21

5)*4 130%6$5 $0.1-*&4 8*5)  $'3

  "/%   &9$&15 '03

%&7*"5*0/4 16346"/5 50 -"4&3 /05*$&

/0  %"5&% +6/&  

&$87,21 

&/$66 % 9,6,%/( $1' ,19,6,%/( /$6(5 5$',$7,21

:+(1 23(1

$92,' (;32685( 72 7+( %($0

9256,&+7 

6,&+7%$5( 81' 816,&+7%$5( /$6(5675$+/81*

./$66( % :(11 *(g))1(7

1,&+7 '(0 675$+/ $866(7=(1

%

Laser :

Type: SW 653L VP

Manufacturer: Hitachi Media Electronics Co., Ltd.

Laser output:

90.1 mW (DVD) and 144 mW (CD) on the objective

lens (Typical)

Wavelength: 785 nm (CD) typ

661 nm (DVD) typ

Standard: IEC60825-1: 2007

For European Customers

Disposal of electrical and electronic equipment

(a) All electrical and electronic equipment should be disposed

of separately from the municipal waste stream via collection

facilities designated by the government or local authorities.

(b) By disposing of electrical and electronic equipment correctly,

you will help save valuable resources and prevent any poten-

tial negative effects on human health and the environment.

(c)

Improper disposal of waste electrical and electronic equipment

can have serious effects on the environment and human health

because of the presence of hazardous substances in the

equipment.

(d)

The Waste Electrical and Electronic Equipment (WEEE)

symbol, which shows a wheeled bin that has been

crossed out, indicates that electrical and electronic

equipment must be collected and disposed of separately

from household waste.

(e)

Return and collection systems are available to end users. For

more detailed information about the disposal of old electri-

cal and electronic equipment, please contact your city office,

waste disposal service or the shop where you purchased the

equipment.

Disposal of batteries and/or accumulators

(a) Waste batteries and/or accumulators should be disposed of

separately from the municipal waste stream via collection

facilities designated by the government or local authorities.

(b) By disposing of waste batteries and/or accumulators correctly,

you will help save valuable resources and prevent any poten-

tial negative effects on human health and the environment.

(c)

Improper disposal of waste batteries and/or accumulators can

have serious effects on the environment and human health

because of the presence of hazardous substances in them.

(d) The WEEE symbol, which shows a wheeled bin that

has been crossed out, indicates that batteries and/or

accumulators must be collected and disposed of sepa-

rately from household waste.

If a battery or accumulator contains more than the specified

values of lead (Pb), mercury (Hg), and/or cadmium (Cd) as

defined in the Battery Directive (2006/66/EC), then the chemi-

cal symbols for those elements will be indicated beneath the

WEEE symbol.

(e) Return and collection systems are available to end users. For

more detailed information about the disposal of waste batter-

ies and/or accumulators, please contact your city office, waste

disposal service or the shop where you purchased them.

Pb, Hg, Cd

Contents

Check to be sure the box contains all the included items

shown below.

Please contact the store where you purchased this unit

if any of these items are missing or have been damaged

during transportation.

RCA audio cable × 1

Power cord × 1

Remote control unit (RC-1306) × 1

Batteries for remote control unit (AAA) × 2

Owner's manual (this document) × 1

Keep this manual in a safe place for future reference.

Warranty card × 1

Included items

Included items .........................................5

Before use .............................................6

Maintenance ...........................................6

Remote control unit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

WAV/DSD files .........................................8

Discs ..................................................9

Names and functions of parts (main unit) ..............11

Connecting equipment ...............................12

Names and functions of parts (remote control) ....... 14

Basic operation ...................................... 16

Playback from a specific track .........................19

Selecting folders and files ............................20

Repeat playback ..................................... 21

Shuffle playback .....................................22

Program playback ...................................23

Dimmer .............................................26

Information shown ..................................27

Pure mode playback .................................28

Troubleshooting ..................................... 29

Specifications ........................................ 30

Thank you for choosing TEAC. Read this manual carefully

to get the best performance from this unit.

Placement precautions

Do not put anything on top of the unit.

Avoid placing the unit in direct sunlight or close to any

source of heat, such as a radiator, heater, open fireplace

or amplifier. Also avoid locations that are subject to vibra-

tions or exposed to excessive dust, cold or moisture.

This unit can be stacked with other 501 series models,

including the AI-501DA.

Place the unit in a stable location near the audio sys-

tem that you will use with it.

Do not move the unit during use.

The voltage supplied to the unit should match the volt-

age printed on the rear panel. If you are in any doubt

regarding this matter, consult an electrician.

As the unit could become warm during operation,

always leave sufficient space around it for ventilation.

When placing this unit, position it so that it is at least 3

cm (1.2") from walls in order to allow good heat dissipa-

tion. When installing it in a rack, leave at least 10 cm (4")

open behind the unit.

Do not open the body of the unit as this might result

in damage to the circuitry or cause electric shock. If a

foreign object should get into the unit, contact your

dealer or TEAC customer support.

When removing the power plug from the wall outlet,

always pull directly on the plug; never yank on the cord.

Depending on the electromagnetic waves of television

broadcasts, interference might appear on television

screens when this unit’s power is on. This does not

mean that this unit or the TV is malfunctioning. If this

occurs, turn this unit’s power off.

Use precaution

Listening to anything at a high volume for a long time

could be harmful to your hearing. In order to protect your

ears, be careful not to set the volume too high when lis-

tening with headphones for a long time.

Before use Maintenance

If the surface of the unit becomes dirty, wipe it with a

soft dry cloth. If the unit becomes very dirty, dampen a

soft cloth slightly with a diluted neutral cleanser and thor-

oughly wring out any excess fluid before using the cloth

to wipe the unit.

Q For your safety, disconnect the power cord from

the socket before cleaning.

Never spray liquid directly on the unit.

Do not use thinner or alcohol as they could damage

the surface of the unit.

Avoid allowing rubber or plastic materials to touch this

product for long periods of time, because they could

damage the cabinet.

Remote control unit

Precautions for use

Q Misuse of batteries could cause them to rupture or

leak leading to fire, injury or the staining of items

nearby. Please carefully read and observe the pre-

cautions on page 3.

Point the remote control unit at the main unit’s remote

sensor from within 5 meters (16 feet) of it. Make sure

that there are no obstacles between the remote con-

trol and the main unit.

If direct sunlight or strong artificial illumination shines

on the remote sensor, the remote control might not

function. If that is the case, move this unit to another

location.

If the remote control unit is operated near other

devices that generate infrared rays, or if other remote

control devices using infrared rays are used near the

unit, it might operate incorrectly. The other devices

might also operate incorrectly.

Battery Installation

Remove the cover from the back of the remote control and

insert two AAA batteries with their ¥/^ oriented as shown

in the case. Replace the cover.

Battery Replacement

If the operating range required between the remote control

unit and main unit decreases, the batteries are exhausted. In

this case, replace the batteries with new ones.

For more information about collection of batteries, please

contact your local government, your waste disposal service

or the point of sale where you purchased the collection.

WAV/DSD files

This unit can play back WAV files on CD-ROM/R/RW discs

and WAV and DSD (Direct Stream Digital) DVD-ROM/±R/

RW discs. When using a computer to prepare WAV/DSD

files, carefully read the instructions for the software you

are using.

The display of this unit can only show single-byte let-

ters and numbers. If the file information uses Japanese,

Chinese or other double-byte characters, playback is

possible but the name will not be shown correctly.

Always include the extension in the file name. This unit

recognizes WAV files by their “.wav” file extensions or

DSD files by their “.dsf” file extensions.

Files without extensions cannot be played. Files that are

not in the WAV or DSD format cannot be played even if

they have “.wav” or “.dsf” file extensions.

Discs that contain more than 999 folders and files in

total might not play back properly on this unit.

Depending on disc conditions, this unit might not be

able to play a disc or skipping might occur.

Playable WAV file formats

Files on CD-ROM/R/RW discs

Audio: mono or stereo

Sampling frequency: 44.1 kHz or 48 kHz (88.2 kHz and

higher cannot be played back)

Encoding bit rate: 16-bit or 24-bit

Files on DVD-ROM/±R/RW discs

Audio: mono or stereo

Sampling frequency: 44.1 kHz, 88.2 kHz, 176.4 kHz,

48 kHz, 96 kHz or 192 kHz

Encoding bit rate: 16-bit or 24-bit

Playable DSD file formats

Files on CD-ROM/R/RW discs

Playback of DSD files is not possible.

Files on DVD-ROM/±R/RW discs

Two-channel stereo

2.8 MHz and 5.6 MHz (double-rate) DSD formats

Discs (1)

Audio CDs

CDs that bear the “COMPACT disc DIGITAL

AUDIO” logo (12 cm/4.7")

This unit cannot play back 8 cm CDs.

Depending on disc quality and recording conditions,

playback of some discs might not be possible.

Playback of any other disc type could result

in an unpleasant loud noise, damage to the

speakers as well as potential harm to your hear-

ing. Never play back any other type of disc.

The logo should be on the disc label or the CD jacket.

Video CDs cannot be played on this unit.

Copy-protected discs, dual-layer discs and other discs

that do not conform to the CD standard might not

play correctly in this player. If you use such discs in this

unit, TEAC corporation and its subsidiaries will not be

responsible for any consequences or guarantee the

quality of reproduction. If you experience problems

with such non-standard discs, you should contact their

issuers.

CD-ROM/CD-R/CD-RW discs

This unit can play back CD-ROM/R/RW discs that are in

audio CD or ISO 9660 LEVEL 1/2/JOLIET formats.

Discs created by a CD recorder must be finalized with

the CD recorder that was used to create the discs

before being used with this unit.

Discs that have not been finalized cannot be played

back. Finalize discs with the device used to record WAV

files on them.

If you are uncertain about the handling of a CD-R

or CD-RW disc, please contact the seller of the disc

directly.

DVD-ROM/±R/RW discs

This unit can play back DVD-ROM/±R/RW discs that

contain WAV or DSD files that are in UDF or DVD-ROM-

compatible formats.

This unit cannot play back Super Audio CDs.

DVD video, DVD audio and related formats cannot be

played back.

Inserting discs

1. Hold the edges of disc with the label side up and insert

it into the slot part way as shown in the illustration.

2. Continue pushing the disc in until it is almost com-

pletely hidden in the slot and it will be pulled in the

rest of the way automatically.

If the disc does not load properly

If the disc gets caught or is otherwise difficult to push, do

not try to force it into the slot. Press the EJECT (-) but-

ton and remove the disc once and then try to reinsert it.

(If you try to force the disc, the disc or this unit could be

damaged.)

Discs (2)

CAUTION

Do not play any disc that is warped, deformed or dam-

aged. Playing such discs could cause irreparable harm

to the playing mechanisms.

While printable CD-R and CD-RW discs utilizing mod-

ern printing technologies are generally acceptable,

older systems that use adhesives to attach paper type

labels to the disc surface are not recommended.

Do not stick papers or protective sheets on the discs

and do not use any protective coating sprays.

Never use a stabilizer. Using commercially available CD

stabilizers with this unit will damage the mechanisms

and cause them to malfunction.

Do not use irregularly-shaped discs (octagonal, heart-

shaped, business-card-size, etc.). CDs with these shapes

could damage the unit.

Storage precautions

Discs should be returned to their cases after use to

avoid dust and scratches that could cause the laser

pickup to “skip.”

Do not expose discs to direct sunlight or high tempera-

ture and humidity for extended periods. Long exposure

to high temperatures will warp discs.

CD-R and CD-RW discs are more sensitive to the effects

of heat and ultraviolet rays than ordinary CDs. It is

important that they are not stored in locations where

they will be exposed to direct sunlight. They should

also be kept away from sources of heat, such as radia-

tors and heat-generating electrical devices.

Maintenance

If the side of the disc on which data is recorded has fin-

gerprints or dust on it, use a soft cloth to gently wipe it

radially from the center hole toward the outside edge.

Never clean discs using chemicals such as record

sprays, antistatic sprays and fluids, and thinner. Such

chemicals will do irreparable damage to the disc’s plas-

tic surface.

If you are in any doubt as to the care and handling of a

disc, read the precautions supplied with the disc or con-

tact the disc manufacturer.

POWER switch

Use to turn the power ON and OFF.

Remote control signal receiver

Signals from the remote control are received here.

When using the remote control, point it toward this

area.

Disc slot

Insert a disc here. After the disc has been partially

inserted, it will be automatically pulled into the slot.

Display

This shows various information (see page 27).

Eject button (-)

Press when the unit is stopped to partially eject the

disc. Hold the disc by its edges and pull it out.

Stop button (8)

Press during playback to stop the disc.

Names and functions of parts (main unit)

A GE IB D F

Skip (.) button

Press to skip to the previous track (see page 19).

Press and hold during playback to search backward

(see page 18).

Play/pause button (7/9)

Press when stopped to start playback.

Press during disc playback to pause.

Press again to restart playback.

Skip (/) button

Press to skip to the next track. Press and hold during

playback to search forward (see page 19).

REPEAT button

Press to change the repeat playback mode (see page

21).

When both the main unit and the remote control have

buttons with the same functions, this manual explains

how to use either of them. The corresponding buttons

can be used in the same manner.

Connecting equipment

B C

Stereo amplier or

powered speakers, etc.

DIGITAL IN

(COAXIAL)

DIGITAL IN

(OPTICAL)

Digital audio

input device

Digital audio

input device

RCA audio cable

RCA coaxial digital cable

Optical digital cable

Included power cord

Wall socket

Audio input

(LINE IN, etc.)

AUTO POWER SAVE switch

Use to turn the automatic power saving function ON

and OFF.

When ON, the unit will automatically enter standby

mode if there is no audio output for 30 minutes or

more.

When in standby mode, press a button on this unit

or the remote control to turn the power ON.

Analog audio output connectors

(LINE OUT)

These RCA jacks output two channels of analog audio

signals. Connect these to an amplifier or other device

with audio inputs.

Use commercially available audio cables to make

the connections.

White (L)

Red (R)

White (L)

Red (R)

DIGITAL OUT audio output connectors

These output digital audio. Connect these to the digi-

tal audio inputs of devices that accept digital audio

signals.

COAXIAL: RCA coaxial digital cable

OPTICAL: Optical digital cable (TOS)

Use commercially available cables to make the

connections.

The sampling frequency and bit rate used by

the digital outputs (COAXIAL and OPTICAL) are

the same as for the playback source. During DSD

playback or CD/PCM playback in pure mode,

however, nothing is output from the digital

outputs.

Power inlet (

IN)

Insert the included power cord here. After complet-

ing all other connections, insert the power plug into a

power outlet.

Unplug the cord from the outlet when not using the

unit for a long time.

V Use only the included power cord. Use of a differ-

ent cord could cause fire or electric shock.

Do not turn the power on until after

making all connections.

Carefully read the manuals of the devices that

you are connecting and follow their instructions

when making connections.

Do not bundle connecting cables with power

cords. Doing so could cause noise.

Connect all plugs completely.

Names and functions of parts (remote control)

PURE mode button

Press when playback is stopped to turn pure mode

playback ON and OFF (see page 28).

SELECT button

Confirm items selected using the FOLDER( k/j) and

skip (.//) buttons (see page 20).

When a WAV/DSD disc is loaded and playback is

stopped, press the SELECT button to switch between

disc and folder modes (see page 16).

PROGRAM button

Use for program playback (see pages 23-26).

Shuffle [½] button

Use for shuffle playback (see page 22).

Repeat [¼] button

Use for repeat playback (see page 21).

Stop [8] button

Press during playback to stop playback (see page

18).

When both the main unit and the remote control have

buttons with the same functions, this manual explains

how to use either of them. The corresponding buttons

can be used in the same manner.

DIMMER button

Use to adjust the brightness of the main unit's display

(see page 26).

DISPLAY button

Press to change what is shown on the display (see

page 27).

FOLDER [k/j] buttons

When playing back a WAV/DSD disc, press to skip to

the previous or next folder (see page 20).

Number buttons

Use for track selection and preparing a program (see

pages 19 and 23-26).

CLEAR button

Press to clear a track added to the program (see page

25).

Search [m/,] buttons

During playback, press and hold one of these buttons

to search forward or backward (see page 18).

Skip [.//] buttons

Use to skip to the previous or next track (see page

19).

Play/pause [7/9] button

Press when stopped to start playback (see page 17).

Press during playback to pause. Press again when

paused to resume playback.

2 3

Set the POWER switch to ON .

Hold the edges of the disc with the label

side up and partially insert it into the slot.

Continue pushing the disc in until it is

almost completely hidden in the slot. It

will be pulled in the rest of the way

automatically.

If the disc gets caught or is otherwise difficult to push,

do not try to force it into the slot. Press the EJECT (-)

button and remove the disc once and then try to rein-

sert it. (If you try to force the disc, the disc or this unit

could be damaged.)

When a WAV/DSD disc is loaded and playback

is stopped, press the SELECT button to switch

between disc and folder modes.

Basic operation (1)

Example of display when audio CD loaded

Total number of

tracks on the disc

Total playback time

Status indicator

Examples of display when WAV/DSD disc loaded

Disc mode (playback of entire disk)

Status indicator

Total number of tracks on the disc

Folder mode (playback of selected folder)

Total number of tracks in folder

Status indicator

The indicator in the top left corner shows the

playback status.

8 Stopped

7 Playing back

9 Paused

m Searching backward

, Searching forward

Press the play/pause (y/9) button to

start playback.

Example of display when audio CD loaded

Number of the track

being played back

Elapsed time of

the track being

played back

Example of display when WAV disc loaded

Number of

the track being

played back

Elapsed time of the track

being played back

(hours: minutes: seconds)

File type Sampling frequency

Example of display when DSD disc loaded

File type Sampling frequency

Number of

the track being

played back

Elapsed time of the track

being played back

(hours: minutes: seconds)

A little time is required to load a disc. While a disc

is loading, buttons will not function when pressed.

Wait until the total number of tracks and total play-

back time (when an audio CD is loaded) appear

before pressing any buttons.

The unit stops when playback of the last track

finishes.

“No Disc” appears on the display when no disc has

been loaded in the disc slot.

WAV/DSD files that are not in folders are automati-

cally placed in the “ROOT” folder. Playback starts with

the first track in the ROOT folder.

Folders that do not contain any WAV/DSD files are

skipped during playback.

Basic operation (2)

Stopping playback

Press the stop (8) button.

Ejecting a disc

When stopped, press the eject (-) button.

The disc will be partially ejected. Hold the edges of the

disc and pull it out.

Pausing playback

Press the play/pause (y/9) button.

Press the play/pause (y/9) button again to resume

playback.

Searching for part of a track

During playback, press and hold a skip (.//) button

to search backward or forward.

Release the button when you find the part you want.

If you search forward to the end of the last track, the

unit will stop.

You can also use the search (m/,) buttons on the

remote control for this.

Playback from a specific track

Skipping to the desired track

During playback, press a skip (.//) button to skip

to the previous or next track and start playing it back.

Press the button repeatedly until you reach the desired

track number.

When stopped or paused, the unit will stop or pause

at the beginning of the selected track. Press the play/

pause (y/9) button to start playback.

During playback, press . once to return to the

beginning of the currently playing track. Press .

repeatedly if you want to play an earlier track.

During program playback, these operations will skip to

earlier and later tracks in program order.

During playback or when stopped, use the number but-

tons to enter a track number and start playback from that

track.

Examples:

Track number 3: or

Track number 15:

Track number 107:

Selecting folders and files

During playback and when stopped, you can search for

WAV/DSD folders and tracks that you want to find.

Selecting a folder

Use the FOLDER (k/j) buttons to select the desired

folder, and press the SELECT button.

Folder number

Folder name

Playback starts from the first track in the selected folder.

Depending on the folder structure, the order of folders

and tracks might not be as expected.

Selecting a track

Use the skip (.//) buttons to select the desired

track, and press the play/pause (7/9) button.

Folder number File number

File name

Playback starts from the select track.

When you want to select a track that is inside a folder,

you must select the folder first.

The display of this unit can only show single-byte let-

ters of the alphabet and numbers. If the name of a file

uses Japanese, Chinese or other double-byte charac-

ters, the file will be playable but the name will not be

shown correctly.

The information displayed depends on the display set-

ting (see page 27).

If you want to see the file names, press the DISPLAY

button to change the information displayed.

La page est en cours de chargement...

TEAC PD-501HR Le manuel du propriétaire

Marque: TEAC

Modèle: PD-501HR

Catégorie: Lecteurs DVD

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: TEAC PD-501HR Owner's manual

TEAC PD-501HR Le manuel du propriétaire

TEAC PD-501HR Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents