TEAC PD-501HR Le manuel du propriétaire

Catégorie
Lecteurs DVD
Taper
Le manuel du propriétaire
D01179820B
Z
PD-501HR
CD Player
OWNER’S MANUAL
MODE D’EMPLOI
MANUAL DEL USUARIO
2
IMPORTANT SAFETY PRECAUTIONS
CAUTION
o
DO NOT REMOVE THE EXTERNAL CASES OR CABINETS TO
EXPOSE THE ELECTRONICS. NO USER SERVICEABLE PARTS
ARE INSIDE.
o
IF YOU ARE EXPERIENCING PROBLEMS WITH THIS PRODUCT,
CONTACT TEAC FOR A SERVICE REFERRAL. DO NOT USE THE
PRODUCT UNTIL IT HAS BEEN REPAIRED.
o
USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF
PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY
RESULT IN HAZARDOUS RADIATION EXPOSURE.
WARNING: TO PREVENT FIRE OR SHOCK HAZARD,
DO NOT EXPOSE THIS APPLIANCE TO RAIN OR
MOISTURE.
IN USA/CANADA, USE ONLY ON 120 V SUPPLY.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS
INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the
presence of uninsulated dangerous voltage” within the
product’s enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in the
literature accompanying the appliance.
For Canada
Industry Canada’s Compliance Statement:
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil nurique de la classe B est conforme à la norme
NMB-003 du Canada.
For U.S.A.
This equipment complies with Part 15 of FCC Rules. Operation is
subject to the following two conditions: 1) This device may not
cause interference and 2) This device must accept any interference,
including interference that may cause undesired operation of the
device.
Information to the user:
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equip-
ment generates, uses, and can radiate radio frequency energy and,
if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
Reorient or relocate the equipment and/or the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for
help.
CAUTION
Changes or modifications to this equipment not expressly approved
by TEAC CORPORATION for compliance will void the user’s warranty.
“DSD” is a registered trademark.
Other company names and product names in this document are the trademarks or registered trademarks of their respective owners.
3
IMPORTANT SAFETY INSTRUCTIONS
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings. Install in accordance with
the manufacturer's instructions.
8)
Do not install near any heat sources such as radiators, heat registers,
stoves, or other apparatus (including amplifiers) that produce heat.
9) Do not defeat the safety purpose of the polarized or grounding-
type plug. A polarized plug has two blades with one wider than
the other. A grounding type plug has two blades and a third
grounding prong. The wide blade or the third prong are provided
for your safety. If the provided plug does not fit into your outlet,
consult an electrician for replacement of the obsolete outlet.
10) Protect the power cord from being walked on or pinched
particularly at plugs, convenience receptacles, and the point
where they exit from the apparatus.
11) Only use attachments/accessories specified by the manufacturer.
12) Use only with the cart, stand, tripod, bracket, or
table specified by the manufacturer, or sold with
the apparatus. When a cart is used, use caution
when moving the cart/apparatus combination
to avoid injury from tip-over.
13) Unplug this apparatus during lightning storms or
when unused for long periods of time.
14) Refer all servicing to qualified service personnel. Servicing is
required when the apparatus has been damaged in any way, such
as power-supply cord or plug is damaged, liquid has been spilled
or objects have fallen into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate normally, or has
been dropped.
o
The apparatus draws nominal non-operating power from the AC
outlet with its POWER or STANDBY/ON switch not in the ON position.
o
The mains plug is used as the disconnect device, the disconnect
device shall remain readily operable.
o
Caution should be taken when using earphones or headphones
with the product because excessive sound pressure (volume) from
earphones or headphones can cause hearing loss.
o
Do not expose this apparatus to drips or splashes.
o
Do not place any objects filled with liquids, such as vases, on
the apparatus.
o
Do not install this apparatus in a confined space such as a book
case or similar unit.
o
The apparatus should be located close enough to the AC outlet
so that you can easily reach the power cord plug at any time.
o
If the product uses batteries (including a battery pack or
installed batteries), they should not be exposed to sunshine, fire
or excessive heat.
o
CAUTION for products that use replaceable lithium batteries: there
is danger of explosion if a battery is replaced with an incorrect
type of battery. Replace only with the same or equivalent type.
Products with Class construction are equipped with a power sup-
ply cord that has a grounding plug. The cord of such a product
must be plugged into an AC outlet that has a protective ground-
ing connection.
CAUTION
WARNING
Q
Precautions concerning batteries
Misuse of batteries could cause them to rupture or leak leading
to fire, injury or the staining of nearby things. Please read and
observe the following precautions carefully.
o Be sure to insert the batteries with correct positive (+) and
negative (_) orientations.
o Use batteries of the same type. Never use different types of bat-
teries together.
o If the remote control is not used for a long time (more than a
month), remove the batteries to prevent them from leaking.
o If the batteries leak, wipe away the leakage inside the battery
compartment and replace the batteries with new ones.
o Do not use batteries of types other than those specified. Do not
mix new batteries with old ones or use different types of batter-
ies together.
o Do not heat or disassemble batteries. Never throw batteries into
fire or water.
o Do not carry or store batteries with other metallic objects. The
batteries could short circuit, leak or explode.
o Never recharge a battery unless it is confirmed to be a recharge-
able type.
This product has been designed and manufactured according to FDA
regulations “title 21, CFR, chapter 1, subchapter J, based on the
Radiation Control for Health and Safety Act of 1968”, and is classified as
class
laser product. There is not hazardous invisible laser radiation
during operation because invisible laser radiation emitted inside of
this product is completely confined in the protective housings.
The label required in this regulation is as follows:
&(57,),&$7,21
5)*4 130%6$5 $0.1-*&4 8*5)  $'3
  "/%   &9$&15 '03
%&7*"5*0/4 16346"/5 50 -"4&3 /05*$&
/0  %"5&% +6/&  
&$87,21
&/$66 % 9,6,%/( $1' ,19,6,%/( /$6(5 5$',$7,21
:+(1 23(1
$92,' (;32685( 72 7+( %($0
9256,&+7
6,&+7%$5( 81' 816,&+7%$5( /$6(5675$+/81*
./$66( % :(11 *(g))1(7
1,&+7 '(0 675$+/ $866(7=(1
%
Laser :
Type: SW 653L VP
Manufacturer: Hitachi Media Electronics Co., Ltd.
Laser output:
90.1 mW (DVD) and 144 mW (CD) on the objective
lens (Typical)
Wavelength: 785 nm (CD) typ
661 nm (DVD) typ
Standard: IEC60825-1: 2007
4
For European Customers
Disposal of electrical and electronic equipment
(a) All electrical and electronic equipment should be disposed
of separately from the municipal waste stream via collection
facilities designated by the government or local authorities.
(b) By disposing of electrical and electronic equipment correctly,
you will help save valuable resources and prevent any poten-
tial negative effects on human health and the environment.
(c)
Improper disposal of waste electrical and electronic equipment
can have serious effects on the environment and human health
because of the presence of hazardous substances in the
equipment.
(d)
The Waste Electrical and Electronic Equipment (WEEE)
symbol, which shows a wheeled bin that has been
crossed out, indicates that electrical and electronic
equipment must be collected and disposed of separately
from household waste.
(e)
Return and collection systems are available to end users. For
more detailed information about the disposal of old electri-
cal and electronic equipment, please contact your city office,
waste disposal service or the shop where you purchased the
equipment.
Disposal of batteries and/or accumulators
(a) Waste batteries and/or accumulators should be disposed of
separately from the municipal waste stream via collection
facilities designated by the government or local authorities.
(b) By disposing of waste batteries and/or accumulators correctly,
you will help save valuable resources and prevent any poten-
tial negative effects on human health and the environment.
(c)
Improper disposal of waste batteries and/or accumulators can
have serious effects on the environment and human health
because of the presence of hazardous substances in them.
(d) The WEEE symbol, which shows a wheeled bin that
has been crossed out, indicates that batteries and/or
accumulators must be collected and disposed of sepa-
rately from household waste.
If a battery or accumulator contains more than the specified
values of lead (Pb), mercury (Hg), and/or cadmium (Cd) as
defined in the Battery Directive (2006/66/EC), then the chemi-
cal symbols for those elements will be indicated beneath the
WEEE symbol.
(e) Return and collection systems are available to end users. For
more detailed information about the disposal of waste batter-
ies and/or accumulators, please contact your city office, waste
disposal service or the shop where you purchased them.
Pb, Hg, Cd
5
EN
Contents
Check to be sure the box contains all the included items
shown below.
Please contact the store where you purchased this unit
if any of these items are missing or have been damaged
during transportation.
RCA audio cable × 1
Power cord × 1
Remote control unit (RC-1306) × 1
Batteries for remote control unit (AAA) × 2
Owner's manual (this document) × 1
o
Keep this manual in a safe place for future reference.
Warranty card × 1
Included items
Included items .........................................5
Before use .............................................6
Maintenance ...........................................6
Remote control unit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
WAV/DSD files .........................................8
Discs ..................................................9
Names and functions of parts (main unit) ..............11
Connecting equipment ...............................12
Names and functions of parts (remote control) ....... 14
Basic operation ...................................... 16
Playback from a specific track .........................19
Selecting folders and files ............................20
Repeat playback ..................................... 21
Shuffle playback .....................................22
Program playback ...................................23
Dimmer .............................................26
Information shown ..................................27
Pure mode playback .................................28
Troubleshooting ..................................... 29
Specifications ........................................ 30
Thank you for choosing TEAC. Read this manual carefully
to get the best performance from this unit.
6
V
Placement precautions
o
Do not put anything on top of the unit.
o
Avoid placing the unit in direct sunlight or close to any
source of heat, such as a radiator, heater, open fireplace
or amplifier. Also avoid locations that are subject to vibra-
tions or exposed to excessive dust, cold or moisture.
o
This unit can be stacked with other 501 series models,
including the AI-501DA.
o
Place the unit in a stable location near the audio sys-
tem that you will use with it.
o
Do not move the unit during use.
o
The voltage supplied to the unit should match the volt-
age printed on the rear panel. If you are in any doubt
regarding this matter, consult an electrician.
o
As the unit could become warm during operation,
always leave sufficient space around it for ventilation.
When placing this unit, position it so that it is at least 3
cm (1.2") from walls in order to allow good heat dissipa-
tion. When installing it in a rack, leave at least 10 cm (4")
open behind the unit.
o
Do not open the body of the unit as this might result
in damage to the circuitry or cause electric shock. If a
foreign object should get into the unit, contact your
dealer or TEAC customer support.
o
When removing the power plug from the wall outlet,
always pull directly on the plug; never yank on the cord.
o
Depending on the electromagnetic waves of television
broadcasts, interference might appear on television
screens when this unit’s power is on. This does not
mean that this unit or the TV is malfunctioning. If this
occurs, turn this units power off.
V
Use precaution
Listening to anything at a high volume for a long time
could be harmful to your hearing. In order to protect your
ears, be careful not to set the volume too high when lis-
tening with headphones for a long time.
Before use Maintenance
If the surface of the unit becomes dirty, wipe it with a
soft dry cloth. If the unit becomes very dirty, dampen a
soft cloth slightly with a diluted neutral cleanser and thor-
oughly wring out any excess fluid before using the cloth
to wipe the unit.
Q For your safety, disconnect the power cord from
the socket before cleaning.
o
Never spray liquid directly on the unit.
o
Do not use thinner or alcohol as they could damage
the surface of the unit.
o
Avoid allowing rubber or plastic materials to touch this
product for long periods of time, because they could
damage the cabinet.
7
EN
Remote control unit
Precautions for use
Q Misuse of batteries could cause them to rupture or
leak leading to fire, injury or the staining of items
nearby. Please carefully read and observe the pre-
cautions on page 3.
o
Point the remote control unit at the main unit’s remote
sensor from within 5 meters (16 feet) of it. Make sure
that there are no obstacles between the remote con-
trol and the main unit.
o
If direct sunlight or strong artificial illumination shines
on the remote sensor, the remote control might not
function. If that is the case, move this unit to another
location.
o
If the remote control unit is operated near other
devices that generate infrared rays, or if other remote
control devices using infrared rays are used near the
unit, it might operate incorrectly. The other devices
might also operate incorrectly.
Battery Installation
Remove the cover from the back of the remote control and
insert two AAA batteries with their ¥/^ oriented as shown
in the case. Replace the cover.
Battery Replacement
If the operating range required between the remote control
unit and main unit decreases, the batteries are exhausted. In
this case, replace the batteries with new ones.
For more information about collection of batteries, please
contact your local government, your waste disposal service
or the point of sale where you purchased the collection.
8
WAV/DSD files
This unit can play back WAV files on CD-ROM/R/RW discs
and WAV and DSD (Direct Stream Digital) DVD-ROM/±R/
RW discs. When using a computer to prepare WAV/DSD
files, carefully read the instructions for the software you
are using.
o
The display of this unit can only show single-byte let-
ters and numbers. If the file information uses Japanese,
Chinese or other double-byte characters, playback is
possible but the name will not be shown correctly.
o
Always include the extension in the file name. This unit
recognizes WAV files by their “.wav” file extensions or
DSD files by their “.dsf” file extensions.
o
Files without extensions cannot be played. Files that are
not in the WAV or DSD format cannot be played even if
they have “.wav” or “.dsf” file extensions.
o
Discs that contain more than 999 folders and files in
total might not play back properly on this unit.
o
Depending on disc conditions, this unit might not be
able to play a disc or skipping might occur.
Playable WAV file formats
Files on CD-ROM/R/RW discs
o
Audio: mono or stereo
o
Sampling frequency: 44.1 kHz or 48 kHz (88.2 kHz and
higher cannot be played back)
o
Encoding bit rate: 16-bit or 24-bit
Files on DVD-ROM/±R/RW discs
o
Audio: mono or stereo
o
Sampling frequency: 44.1 kHz, 88.2 kHz, 176.4 kHz,
48 kHz, 96 kHz or 192 kHz
o
Encoding bit rate: 16-bit or 24-bit
Playable DSD file formats
Files on CD-ROM/R/RW discs
o
Playback of DSD files is not possible.
Files on DVD-ROM/±R/RW discs
o
Two-channel stereo
o
2.8 MHz and 5.6 MHz (double-rate) DSD formats
9
EN
Discs (1)
Audio CDs
CDs that bear the “COMPACT disc DIGITAL
AUDIO” logo (12 cm/4.7")
o
This unit cannot play back 8 cm CDs.
o
Depending on disc quality and recording conditions,
playback of some discs might not be possible.
V
Playback of any other disc type could result
in an unpleasant loud noise, damage to the
speakers as well as potential harm to your hear-
ing. Never play back any other type of disc.
o
The logo should be on the disc label or the CD jacket.
o
Video CDs cannot be played on this unit.
o
Copy-protected discs, dual-layer discs and other discs
that do not conform to the CD standard might not
play correctly in this player. If you use such discs in this
unit, TEAC corporation and its subsidiaries will not be
responsible for any consequences or guarantee the
quality of reproduction. If you experience problems
with such non-standard discs, you should contact their
issuers.
CD-ROM/CD-R/CD-RW discs
This unit can play back CD-ROM/R/RW discs that are in
audio CD or ISO 9660 LEVEL 1/2/JOLIET formats.
o
Discs created by a CD recorder must be finalized with
the CD recorder that was used to create the discs
before being used with this unit.
o
Discs that have not been finalized cannot be played
back. Finalize discs with the device used to record WAV
files on them.
o
If you are uncertain about the handling of a CD-R
or CD-RW disc, please contact the seller of the disc
directly.
DVD-ROM/±R/RW discs
This unit can play back DVD-ROM/±R/RW discs that
contain WAV or DSD files that are in UDF or DVD-ROM-
compatible formats.
o
This unit cannot play back Super Audio CDs.
o
DVD video, DVD audio and related formats cannot be
played back.
Inserting discs
1. Hold the edges of disc with the label side up and insert
it into the slot part way as shown in the illustration.
2. Continue pushing the disc in until it is almost com-
pletely hidden in the slot and it will be pulled in the
rest of the way automatically.
If the disc does not load properly
If the disc gets caught or is otherwise difficult to push, do
not try to force it into the slot. Press the EJECT (-) but-
ton and remove the disc once and then try to reinsert it.
(If you try to force the disc, the disc or this unit could be
damaged.)
10
Discs (2)
CAUTION
o
Do not play any disc that is warped, deformed or dam-
aged. Playing such discs could cause irreparable harm
to the playing mechanisms.
o
While printable CD-R and CD-RW discs utilizing mod-
ern printing technologies are generally acceptable,
older systems that use adhesives to attach paper type
labels to the disc surface are not recommended.
o
Do not stick papers or protective sheets on the discs
and do not use any protective coating sprays.
o
Never use a stabilizer. Using commercially available CD
stabilizers with this unit will damage the mechanisms
and cause them to malfunction.
o
Do not use irregularly-shaped discs (octagonal, heart-
shaped, business-card-size, etc.). CDs with these shapes
could damage the unit.
Storage precautions
o
Discs should be returned to their cases after use to
avoid dust and scratches that could cause the laser
pickup to “skip.
o
Do not expose discs to direct sunlight or high tempera-
ture and humidity for extended periods. Long exposure
to high temperatures will warp discs.
o
CD-R and CD-RW discs are more sensitive to the effects
of heat and ultraviolet rays than ordinary CDs. It is
important that they are not stored in locations where
they will be exposed to direct sunlight. They should
also be kept away from sources of heat, such as radia-
tors and heat-generating electrical devices.
Maintenance
o
If the side of the disc on which data is recorded has fin-
gerprints or dust on it, use a soft cloth to gently wipe it
radially from the center hole toward the outside edge.
o
Never clean discs using chemicals such as record
sprays, antistatic sprays and fluids, and thinner. Such
chemicals will do irreparable damage to the disc’s plas-
tic surface.
If you are in any doubt as to the care and handling of a
disc, read the precautions supplied with the disc or con-
tact the disc manufacturer.
11
EN
A
POWER switch
Use to turn the power ON and OFF.
B
Remote control signal receiver
Signals from the remote control are received here.
When using the remote control, point it toward this
area.
C
Disc slot
Insert a disc here. After the disc has been partially
inserted, it will be automatically pulled into the slot.
D
Display
This shows various information (see page 27).
E
Eject button (-)
Press when the unit is stopped to partially eject the
disc. Hold the disc by its edges and pull it out.
F
Stop button (8)
Press during playback to stop the disc.
Names and functions of parts (main unit)
A GE IB D F
H
JC
G
Skip (.) button
Press to skip to the previous track (see page 19).
Press and hold during playback to search backward
(see page 18).
H
Play/pause button (7/9)
Press when stopped to start playback.
Press during disc playback to pause.
Press again to restart playback.
I
Skip (/) button
Press to skip to the next track. Press and hold during
playback to search forward (see page 19).
J
REPEAT button
Press to change the repeat playback mode (see page
21).
When both the main unit and the remote control have
buttons with the same functions, this manual explains
how to use either of them. The corresponding buttons
can be used in the same manner.
12
Connecting equipment
B C
D
LR
A
Stereo amplier or
powered speakers, etc.
DIGITAL IN
(COAXIAL)
DIGITAL IN
(OPTICAL)
Digital audio
input device
Digital audio
input device
RCA audio cable
RCA coaxial digital cable
Optical digital cable
Included power cord
Wall socket
Audio input
(LINE IN, etc.)
13
EN
A
AUTO POWER SAVE switch
Use to turn the automatic power saving function ON
and OFF.
When ON, the unit will automatically enter standby
mode if there is no audio output for 30 minutes or
more.
o
When in standby mode, press a button on this unit
or the remote control to turn the power ON.
B
Analog audio output connectors
(LINE OUT)
These RCA jacks output two channels of analog audio
signals. Connect these to an amplifier or other device
with audio inputs.
o
Use commercially available audio cables to make
the connections.
White (L)
Red (R)
White (L)
Red (R)
C
DIGITAL OUT audio output connectors
These output digital audio. Connect these to the digi-
tal audio inputs of devices that accept digital audio
signals.
COAXIAL: RCA coaxial digital cable
OPTICAL: Optical digital cable (TOS)
o
Use commercially available cables to make the
connections.
o
The sampling frequency and bit rate used by
the digital outputs (COAXIAL and OPTICAL) are
the same as for the playback source. During DSD
playback or CD/PCM playback in pure mode,
however, nothing is output from the digital
outputs.
D
Power inlet (
~
IN)
Insert the included power cord here. After complet-
ing all other connections, insert the power plug into a
power outlet.
Unplug the cord from the outlet when not using the
unit for a long time.
V Use only the included power cord. Use of a differ-
ent cord could cause fire or electric shock.
V
Do not turn the power on until after
making all connections.
o
Carefully read the manuals of the devices that
you are connecting and follow their instructions
when making connections.
o
Do not bundle connecting cables with power
cords. Doing so could cause noise.
o
Connect all plugs completely.
14
Names and functions of parts (remote control)
A
PURE mode button
Press when playback is stopped to turn pure mode
playback ON and OFF (see page 28).
B
SELECT button
Confirm items selected using the FOLDER( k/j) and
skip (.//) buttons (see page 20).
When a WAV/DSD disc is loaded and playback is
stopped, press the SELECT button to switch between
disc and folder modes (see page 16).
C
PROGRAM button
Use for program playback (see pages 23-26).
D
Shuffle [½] button
Use for shuffle playback (see page 22).
E
Repeat [¼] button
Use for repeat playback (see page 21).
F
Stop [8] button
Press during playback to stop playback (see page
18).
B
C
D
E
F
A
K
N
H
I
J
L
M
G
When both the main unit and the remote control have
buttons with the same functions, this manual explains
how to use either of them. The corresponding buttons
can be used in the same manner.
15
EN
G
DIMMER button
Use to adjust the brightness of the main unit's display
(see page 26).
H
DISPLAY button
Press to change what is shown on the display (see
page 27).
I
FOLDER [k/j] buttons
When playing back a WAV/DSD disc, press to skip to
the previous or next folder (see page 20).
J
Number buttons
Use for track selection and preparing a program (see
pages 19 and 23-26).
K
CLEAR button
Press to clear a track added to the program (see page
25).
L
Search [m/,] buttons
During playback, press and hold one of these buttons
to search forward or backward (see page 18).
M
Skip [.//] buttons
Use to skip to the previous or next track (see page
19).
N
Play/pause [7/9] button
Press when stopped to start playback (see page 17).
Press during playback to pause. Press again when
paused to resume playback.
16
1
4
2 3
1
Set the POWER switch to ON .
2
Hold the edges of the disc with the label
side up and partially insert it into the slot.
3
Continue pushing the disc in until it is
almost completely hidden in the slot. It
will be pulled in the rest of the way
automatically.
If the disc gets caught or is otherwise difficult to push,
do not try to force it into the slot. Press the EJECT (-)
button and remove the disc once and then try to rein-
sert it. (If you try to force the disc, the disc or this unit
could be damaged.)
o
When a WAV/DSD disc is loaded and playback
is stopped, press the SELECT button to switch
between disc and folder modes.
Basic operation (1)
Example of display when audio CD loaded
Total number of
tracks on the disc
Total playback time
Status indicator
Examples of display when WAV/DSD disc loaded
Disc mode (playback of entire disk)
Status indicator
Total number of tracks on the disc
Folder mode (playback of selected folder)
Total number of tracks in folder
Status indicator
o
The indicator in the top left corner shows the
playback status.
8 Stopped
7 Playing back
9 Paused
m Searching backward
, Searching forward
17
EN
4
Press the play/pause (y/9) button to
start playback.
Example of display when audio CD loaded
Elapsed time of
the track being
Example of display when WAV disc loaded
Elapsed time of the track
being played back
Example of display when DSD disc loaded
Elapsed time of the track
being played back
o
A little time is required to load a disc. While a disc
is loading, buttons will not function when pressed.
Wait until the total number of tracks and total play-
back time (when an audio CD is loaded) appear
before pressing any buttons.
o
The unit stops when playback of the last track
finishes.
o
“No Disc” appears on the display when no disc has
been loaded in the disc slot.
o
WAV/DSD files that are not in folders are automati-
cally placed in the “ROOT” folder. Playback starts with
the first track in the ROOT folder.
o
Folders that do not contain any WAV/DSD files are
skipped during playback.
18
Basic operation (2)
Stopping playback
Press the stop (8) button.
Ejecting a disc
When stopped, press the eject (-) button.
The disc will be partially ejected. Hold the edges of the
disc and pull it out.
Pausing playback
Press the play/pause (y/9) button.
o
Press the play/pause (y/9) button again to resume
playback.
Searching for part of a track
During playback, press and hold a skip (.//) button
to search backward or forward.
Release the button when you find the part you want.
o
If you search forward to the end of the last track, the
unit will stop.
o
You can also use the search (m/,) buttons on the
remote control for this.
19
EN
Playback from a specific track
Skipping to the desired track
During playback, press a skip (.//) button to skip
to the previous or next track and start playing it back.
Press the button repeatedly until you reach the desired
track number.
o
When stopped or paused, the unit will stop or pause
at the beginning of the selected track. Press the play/
pause (y/9) button to start playback.
o
During playback, press . once to return to the
beginning of the currently playing track. Press .
repeatedly if you want to play an earlier track.
o
During program playback, these operations will skip to
earlier and later tracks in program order.
During playback or when stopped, use the number but-
tons to enter a track number and start playback from that
track.
Examples:
Track number 3: or
Track number 15:
Track number 107:
20
Selecting folders and files
During playback and when stopped, you can search for
WAV/DSD folders and tracks that you want to find.
Selecting a folder
Use the FOLDER (k/j) buttons to select the desired
folder, and press the SELECT button.
Folder number
Folder name
Playback starts from the first track in the selected folder.
o
Depending on the folder structure, the order of folders
and tracks might not be as expected.
Selecting a track
Use the skip (.//) buttons to select the desired
track, and press the play/pause (7/9) button.
Folder number File number
File name
Playback starts from the select track.
o
When you want to select a track that is inside a folder,
you must select the folder first.
o
The display of this unit can only show single-byte let-
ters of the alphabet and numbers. If the name of a file
uses Japanese, Chinese or other double-byte charac-
ters, the file will be playable but the name will not be
shown correctly.
o
The information displayed depends on the display set-
ting (see page 27).
If you want to see the file names, press the DISPLAY
button to change the information displayed.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39

TEAC PD-501HR Le manuel du propriétaire

Catégorie
Lecteurs DVD
Taper
Le manuel du propriétaire

dans d''autres langues