0
KEG BEER DISPENSER
FONTAINE À BIÈRE EN FÛT
Models / Modèles:
SBC677BI (Built-in / Encastré)
SBC678OS (Outdoor / Pour usage extérieur)
Owner’s Manual
Manuel du propriétaire
BEFORE USE, PLEASE READ AND FOLLOW ALL SAFETY RULES
AND OPERATING INSTRUCTIONS
AVANT D’UTILISER CET APPAREIL, VEUILLEZ LIRE ET RESPECTER TOUTES
LES RÈGLES DE SÉCURITÉ ET INSTRUCTIONS D’UTILISATION
Felix Storch, Inc.
Summit Appliance Division
770 Garrison Avenue Bronx, NY
10474 www.summitappliance.com
Write the Serial Number here:
Inscrivez le numéro de série ici:
___________________________
1
TABLE OF CONTENTS
Important Safety Information .......................................................................... 2 - 4
Placement and Installation ........................................................................... 5 – 11
Location ........................................................................................................ 5
Accessories .................................................................................................. 5
Location of Parts ........................................................................................... 6
Built-in Installation Dimensions (Model SBC677BI) ................................ 6 – 7
Free-Standing Installation (Model SBC678OS) ............................................ 7
Keg Installation ............................................................................................. 7
Caster Guide ................................................................................................. 7
Installation of CO
2
Cylinder Support ............................................................. 8
CO
2
Regulator and CO
2
Cylinder .................................................................. 8
Installation of CO
2
Air Line Hose to Regulator .............................................. 8
Installation of Tap Cooled System ................................................................. 9
Installation of Beer Tower .............................................................................. 9
Installation of Protective Metal Plate ............................................................. 9
Installation of the Beer Keg ........................................................................... 9
Installation of the Keg Tapper ..................................................................... 10
How to Tap a Keg of Beer ........................................................................... 10
Opening the CO
2
Cylinder Main Valve ........................................................ 10
Adjusting the CO
2
Regulator ....................................................................... 11
Plastic Faucet Lever ................................................................................... 11
Guard Rail ................................................................................................... 11
Dispensing Beer .................................................................................................. 12
Operation ..................................................................................................... 12 – 13
Control Panel .............................................................................................. 12
Defrosting ................................................................................................... 13
Converting to an “All-Refrigerator” ................................................................... 13
Reversing the Door Swing .................................................................................. 13
Cleaning and Maintenance ................................................................................. 14
Problems with the Beer ................................................................................ 15 - 16
Troubleshooting .................................................................................................. 16
Limited Warranty ................................................................................................. 17
French version of this manual .................................................................... 18 - 35
2
Thank you for buying this keg cooler. To ensure that you get the best results from
your new cooler, please take time to read through the instructions in this booklet.
IMPORTANT SAFETY INFORMATION
WARNING!
To reduce the risk of fire, electric shock or injury when using this
appliance, follow these basic precautions:
1. Read all instructions before using the appliance.
2. The appliance must be correctly connected to the power supply.
3. Immediately replace worn power cords, loose plugs and faulty power outlets.
4. Do not operate your appliance in the presence of explosive fumes.
5. Disconnect the appliance from the power supply before cleaning or repairing it.
Only a qualified technician should repair it.
6. Never stand on top of or inside this appliance, or swing on the door
7. To reduce likelihood of injury,
. Avoid putting
weight on top of the appliance.
do not let children play with this appliance
8. Do not operate the valve control unless the CO
2
cylinder is completely installed
and connected.
.
9. Do not attempt to repair or replace any part unless this is recommended in this
Owner’s Manual. Leave other service matters to qualified technical personnel.
10. Keep packing materials away from children as they could become a choking
hazard.
11. Do not spray or flush the beer dispenser with water, and avoid keeping it in a
damp place since this could damage the electrical insulation.
12. The appliance is not intended for use by young children or infirm persons without
super vision. Young children should be supervised to ensure that they do not play
with the appliance.
NOTE: This appliance must be used for its intended purpose only.
DANGER! Risk of child entrapment!
Child entrapment and suffocation are not problems of the past. Junked or
abandoned appliances are still dangerous, even if they will "just sit at the curb
for a few days."
Before discarding your old appliance:
• Take off the door.
• Leave the shelves in place so that children may not easily climb inside.
• This appliance is CFC- and HFC-free and contains small quantities of Isobutane
(R600a) which is environmentally friendly, but flammable. It does not damage the
ozone layer, nor does it increase the greenhouse effect. Care must be taken
during transportation and setting up of the appliance that no parts of the cooling
system are damaged. Leaking coolant can ignite and may damage the eyes.
In the event of any damage:
- Avoid open flames and anything that creates a spark,
- Disconnect from the electrical power line,
- Air the room in which the appliance is located for several minutes, and
- Contact the Service Department for advice.
3
• The more coolant there is in an appliance, the larger the room it should be installed
in. In the event of a leakage, if the appliance is in a small room, there is the danger
of combustible gases building up. For every ounce of coolant at least 325 cubic
feet of room space is required. The amount of coolant in the appliance is stated on
the data plate on the back of the appliance. It is hazardous for anyone other than
an Authorized Service Person to carry out servicing or repairs to this appliance.
• Take serious care when handling, moving, and using the appliance to avoid either
damaging the refrigerant tubing or increasing the risk of a leak.
• Replacing component parts and servicing shall be done by factory authorized
service personnel so as to minimize the risk of possible ignition due to incorrect
parts or improper service.
GROUNDING INSTRUCTIONS:
• This appliance must be grounded. In the event of a malfunction or breakdown,
grounding will reduce the risk of electric shock by providing a path of least
resistance for electric current.
• This appliance is equipped with a power cord having an equipment-grounding
conductor and grounding plug. The plug must be plugged into an appropriate wall
outlet that is installed and grounded in accordance with all existing local codes
and ordinances.
• Consult a qualified electrician or service person if the grounding instructions are
not clearly understood or if doubt exists as to whether your electrical wall outlets
are properly grounded.
SAFETY PRECAUTIONS:
• This appliance must be connected to a properly grounded electrical outlet (see
Grounding Instructions)
• Do not operate this appliance if it has a damaged power cord or plug.
• Do not use this product near water, for example: in a wet basement or near a
swimming pool or sink.
• Always disconnect the appliance from the power supply before cleaning and/or
attempting repairs/servicing.
WARNING: Repairs should be performed by qualified service personnel only.
ELECTRICAL CONNECTION:
This Beer Dispenser requires a standard 115/120-volt, 60Hz electrical outlet with
three-prong ground receptacle. To prevent accidental injury, the cord should be
secured behind the Beer Dispenser and not left exposed or dangling.
Never unplug the Beer Dispenser by pulling on the power cord. Always grip the plug
firmly and pull straight out from the receptacle.
CO
2
GAS CAN BE DANGEROUS
CO
2
cylinders contain high-pressure compressed gas which can be hazardous if not
handled properly. Make sure you READ and UNDERSTAND the following procedures
for CO
2
cylinders BEFORE INSTALLATION.
WARNING
4
1. Always check the D.O.T. (Department of Transportation) test date on the cylinder
neck before installation. If it has been more than 5 years, do not use. Return the
cylinder to your gas supplier.
2. Always connect the CO
2
cylinder to a regulator! Failure to do so may cause an
explosion resulting in possible injury or death when the cylinder valve is opened.
3. Never connect the CO
2
cylinder directly to the product container.
4. Always secure a CO
2
gas cylinder in an upright position.
5. Always keep CO
2
cylinders away from heat. Store extra cylinders in a cool place
(preferably below 70°F). Securely fasten cylinders with a chain in an upright
position when storing.
6. Never drop or throw a CO
2
cylinder.
7. Never connect a product container unless there are at least two safety devices in
the pressure system: one on the CO
2
regulator and the other on the product
container or in the pressure gas line.
8. Always ventilate area after any leakage of CO
2
.
If it becomes difficult to breathe and/or your head starts to ache, abnormal
concentrations of carbon dioxide (CO
2
) may be present in the area ...
CLOSE THE MAIN VALVE ON THE CO
2
CYLINDER, VENTILATE AND LEAVE THE
ROOM IMMEDIATELY!
DON’T WAIT! DO THIS NOW!
Improper disposal of worn out appliances poses a risk of entrapment to children.
• If you have purchased this appliance to replace an old one, remove the gaskets,
latches, lids or doors from the unused appliance. If it was equipped with a door
lock that cannot be opened from the inside, (lock bolt) make sure the lock is
removed, disabled or destroyed before discarding. This will make it impossible for
children to accidentally lock themselves inside the appliance and suffocate.
• The refrigerator system of this appliance is filled with refrigerant and insulating
substances which should be treated and processed separately. Call your nearest
service agent or specialized service center. If you are unable to locate one,
contact your local authorities for proper disposal instructions. Be careful not to
damage any of the refrigeration lines of the appliance.
• For the sake of environmental protection, be careful not to damage the rear wall of
the appliance (the condenser unit or the tubes) when moving the appliance or any
part of the refrigeration system inside the appliance.
IMPORTANT WARNING
Beer is readily available with Summit's new Keg Beer Dispenser; however, it is not
intended to be available to people under the legal age to consume beer. Summit does
not assume liability for the unlawful use or consumption of beer.
PLEASE DRINK RESPONSIBLY – DON'T DRINK AND DRIVE!
– SAVE THESE INSTRUCTIONS –
WARNING
5
PLACEMENT AND INSTALLATION
CAUTION:
After unpacking, you MUST allow this appliance to stand upright for at least 2
hours to allow the lubricant and refrigerant to drain back into the compressor
and stabilize. Failure to do so may adversely affect performance and the
lifetime of this unit.
Location
Place your appliance in a location that is strong enough to support its total weight,
keeping in mind that it will weigh substantially more when fully loaded. In order to
prevent vibration and noise, the keg beer dispenser should be leveled by adjusting
the front leveling legs.
Locate the appliance in a dry area out of direct sunlight and away from heat sources
such as an oven or boiler.
Choose a location that has ambient temperatures above 50°F and below 90°F.
Operation outside this temperature range may result in lowered efficiency or cause
other adverse effects.
Do not kink or pinch the power supply cord between the appliance and the wall or
cabinet.
Warning: This appliance must be installed with a grounded circuit.
Accessories
Remove all packing materials and parts. Inspect to make sure all parts listed below
are present and in good condition. In the event that any accessories are missing and
/or damaged, please either call us at 800-932-4267 or 718-893-3900 or fill out a
service request on our website, www.summitappliance.com/support.
1 Draft arm assembly (with washer)
1 CO
2
cylinder
1 CO
2
regulator
1 Keg tap (American Sankey type)
1 Cleaning kit
Vinyl tubing
1 Stainless steel (removable) floor to protect the unit during keg insertion
1 Guard rail
1 Drip tray
4 Casters (for conversion to portable beer cooler)
2 Hose clamps
8 Small Phillips-head screws
4 Large Phillips-head screws
2 Retainer fixing screws
6
Location of Parts
Built-in Installation Dimensions (Model SBC677BI)
If your appliance is to be built-in, use the dimensions in the diagram and chart below as a
guide when installing:
1.
Draft Arm Assembly
2. Drip Tray
3. Safety Guard Rail
4. Control Panel
5. Beer Keg (not included)
6. Door
7. Stainless Steel Plate
8. Casters (4)
9. CO
2
Gas Regulator
10. CO
2
Gas Cylinder
Model
SBC677BI
A
660mm (26″)
B
610mm (24″)
C
1:
(cabinet with
leveling legs)
2:(with beer tower)
D
152mm (6″)
E
51mm (2″)
7
This model may be installed as a free-standing unit (see clearance dimensions
below). However, for built-in installation, you must provide the following clearances
around the unit for best operation and proper ventilation: 3/16” on both sides, 2” at the
rear and 1/16” at the top. Take care that the air vent at the front of the keg beer
dispenser is never covered or blocked in any way.
Free-standing Installation (Model SBC678OS)
For freestanding installation, 5 inches (127mm) of space at the back and sides of the
unit are suggested, which allows the proper air circulation to cool the compressor and
condenser for energy saving. Air vents should never be blocked.
Keg Installation
Caster Guide
(for use as a freestanding or outdoor beer dispenser)
• Install the four casters (2 locking casters at front) into the unit’s bottom (four screw
holes pre-supplied). Figure 1: before installation. Figure 2: casters installed.
CASTERS
8
Installation of CO
2
Cylinder Support
Installation of CO
2
Cylinder:
Install your fully charged CO
2
cylinder
into the support stand. (See Fig. 3)
Figure 3
CO
2
Regulator and CO
2
Cylinder (Figure 4)
Note: Your CO
2
cylinder is shipped empty to avoid any
possible accidents during transportation. When you
purchase the first keg of beer, have your beer distributor
fill the CO
2
cylinder. You must read and understand the
following procedures for CO
2
1. Install the CO
2
gas line tube to the regulator by
attaching one end of the red tube to the hose
connection on the CO
2
regulator.
cylinders before
installation:
2. Secure the tube by using one of the self-locking black
plastic snap-on clamps.
3. Insert a special washer into the regulator-to-cylinder attachment nut.
4. Attach the CO
2
regulator to the CO
2
cylinder by screwing the regulator nut onto the
cylinder valve and tightening with an adjustable wrench.
5. Remove the bolt with the nut from the cylinder retainer. Using
two screws, attach it inside the unit on the left side of the back
wall. Holes are pre-drilled and screws are included.
6. Slide the cylinder through the retainer and secure it with the bolt
and the nut. Position the cylinder this way so that you will be
able to read the numbers on the gauges and easily access the
shut-off valves.
7. Installation of CO
2
Cylinder: Install the fully charged CO
2
cylinder into the support stand. (Figure 5)
Installation of CO
2
Air Line Hose to Regulator
Attach one end of the (red) air line hose to the hose barb
connection on the CO
2
regulator. Secure hose by using
one of the two (self locking) black plastic snap-on clamps
provided. (Use pliers to snap the clamp tight to assure
that there are no leaks.) (Figure 6)
Figure 5
Figure 4
Figure 6
9
Installation of Tap Cooled System
• Remove the top plug by twisting and pulling out, saving it for later use if you
decide to convert unit to an all-refrigerator.
• Put the base of the tap cooled system to the top hole of unit.
• Hold the base of the tap cooled system.
• Use screwdriver to install 3 screws (included).
• Install the pipe to the base of the tap cooled system.
Installation of the Beer Tower
• Installation of the Beer Tower Gasket: Position the rubber (beer tower) gasket
directly on top of the cabinet aligning all four holes in the gasket with the four holes
on the cabinet.
• Installation of the Beer Tower: Unravel the beer line (hose) from the tower and
insert the beer line and nut through the gasket and into the cabinet. Align the four
holes in the base of the beer tower, gasket and bayonet. The beer faucet should be
facing the front of the cabinet. (6:00 o'clock position) Using a Phillips screwdriver,
attach the beer tower to the cabinet using the four machine screws provided and
tighten firmly.
• Installation of the Beer Tower Faucet Handle: Screw the black faucet handle
(clockwise) onto the beer tower faucet. Hand tighten only.
Installation of Protective Metal Plate
• This plate should always be installed when the keg is in place to protect against
unnecessary damage to the floor of the cabinet.
Installation of the Beer Keg
• Position the beer keg directly in front of the open door. Using keg handles only,
carefully lift the beer keg. (Figure 7)
• To place the beer keg inside the cabinet, brace your knees behind the beer keg.
Lift the front of the keg just enough so the front edge of the keg is resting on the
front edge of the Beer Dispenser bottom cabinet. (Figure 8)
• Grasp the keg handles and slide it all the way into the cabinet.
Figure 8
Figure 7
10
Installation of the Keg Tapper
The Sankey type keg tapper supplied with the beer dispenser is the most widely used
in the United States. However, other types of keg tappers can be used. Before
installing a keg tapper, check with your beer distributor to make sure that the Sankey
type keg tapper can be used.
If you need a keg tapper other than a Sankey type, it is recommended that you
purchase the tapper you need from your beer distributor. Please keep the Sankey
type keg tapper for future use. The Sankey system is becoming more popular. It may
be purchased from our Sales Department at 718-893-3900.
• Installation of the Keg Tapper: IMPORTANT NOTICE: Make sure the pull handle
of the keg tapper is in the "upward" (closed) position before installing on the beer
keg (Figure 9). Insert the keg tapper into the locking neck of the beer keg and
apply a 1/4 turn clockwise to lock into position.
• Installation of the CO
2
Air Line Hose to the Keg Tapper: Attach the open end of
the (red) air line hose to the hose barb connection on the keg tapper. Secure hose
by using the remaining (self locking) plastic snap on clamp provided. (Use pliers to
tighten clamp and assure there are no leaks)
• Installation of the Beer Line Hose to the Keg Tapper: Screw the beer line nut
onto the keg tapper and hand tighten firmly.
IMPORTANT NOTICE: The black rubber washer provided must be installed inside
the beer line connection nut before connecting the beer line to the keg tapper.
• Making the connection between the Keg Tapper and Beer Keg: Before making
(opening) connection between the keg tapper and beer keg, make sure the beer
tower faucet is in the closed position (faucet handle straight back). To engage the
tank connection, pull the keg tapper handle out and push down until it locks into
position.
Listen for positive "click" of the pull handle in the final downward position (Figure 10).
How to Tap a Keg of Beer
• Make sure the CO
2
is turned off and the secondary valve on the regulator is in the
‘Closed’ position.
• Pull out and release the pressure release valve on the tapper to purge any air
pressure.
• Make sure the beer tower faucet is in the closed position.
• Pull tapping handle out and press downward until it locks into position (Figure 10).
The keg is now tapped.
Opening the CO
2
Cylinder Main Valve
• Make sure the secondary shut-off valve (shown in Figure 11 in ’Open’ position) is
closed. To open the main CO
2
cylinder valve, slowly turn the main valve counter-
clockwise until fully open.
• Notice the needle on the regulator gauge starts to climb.
11
Adjusting the CO
2
Regulator
There are two pressure gauges on the CO
2
regulator. The upper gauge #1 monitors
"LOW" (internal keg) pressure and must be adjusted to the correct operating pressure
of 10~12psi/lbs. The lower gauge #2 monitors "HIGH" (CO
2
cylinder) pressure and is
not adjustable. The high pressure gauge also acts as a fuel gauge to let you know
when the C0
2
cylinder needs re-filling.
IMPORTANT: The internal operating pressure of the beer keg should be adjusted
and maintained between 10~ 12psi/lbs. To adjust the "LOW" pressure gauge:
• Using an adjustable wrench, release the adjustment lock nut # 3 (Figure 12).
• Using a flat screwdriver, turn the regulator adjustment screw # 4 (Figure 12).
Clockwise rotation of the adjustment screw will increase low pressure. Counter-
clockwise rotation of the adjustment screw will decrease low pressure
• When the required operating pressure is attained, tighten the adjustment lock
nut # 3.
Plastic Faucet Lever
Attach the black plastic lever (pull handle) to the top of the faucet by tightening it by
hand clockwise until the end, holding in the silver nut underneath so it does not turn. If
there is still a small drip from the faucet, you may have tightened the plastic lever too
much and may need to unscrew silver nut counter-clockwise (as shown) one turn.
Guard Rail
1. Place guard rail on top of cabinet.
2. Fit the legs of the guard rail into the prepared holes in the cabinet top.
3. Secure the guard rail to the cabinet with the eight small Phillips-head screws.
Figure 9 Figure 10 Figure 11 Figure 12
12
DISPENSING BEER
Follow these steps to dispense beer:
1. Make sure the beer dispenser is plugged in properly to a 120V, 60Hz, 15 amp
grounded AC outlet.
2. Place the drip tray under the beer faucet.
3. Open the beer faucet by pulling the tap towards you quickly and completely to
dispense the beer.
4. Increase the pressure if the beer runs too slowly. At the correct pressure and
temperature, a 10-oz glass should be filled in 4 seconds.
5. Hold the glass steady at a 45° angle. When it is 2/3 full, start straightening the
glass. Proper foam should be a tight, creamy head and the collar on an average
glass should be 3/4" to 1" high.
Note: It is normal to see condensation forming on the faucet. It is caused by the
difference in temperature between the cold beer and the inner surfaces of the
faucet when beer is flowing through the line.
OPERATION
Before plugging in your cooler for the first time, remove all packaging, clean the
cooler with a soft rag and a mixture of lukewarm water and baking soda (2 table-
spoons baking soda in 1 quart of water works well) . Wipe dry with soft cloth.
Control Panel
This keg beer dispenser has a temperature range of 36°F to 50°F.
• Power Button : Turns the unit on and off. (Press and hold this button for
approximately 3 seconds.)
• Energy Conservation Button : Pressing this button for 3 seconds will turn
the energy conservation mode ON or OFF. In this mode, the LED light and display
will turn off, and the ºC / ºF light will be on.
• Up Button : Used to raise (warm) the temperature by one degree
Down Button : Used to lower (cool) the temperature by one degree
• °C/°F Button: This unit can display temperatures in either Celsius or Fahrenheit.
To change the scale, press the °C/°F button. A beep will sound and the white light
next to the C or F mode will illuminate.
13
Defrosting
Note that under most ambient conditions, the unit will defrost itself automatically.
However, at colder settings, some frost may build up. Additionally, the more humid
the ambient conditions, the more frost may accumulate. Keep the door closed as
much as possible and avoid opening it unless necessary to minimize frost build-up.
CONVERTING TO AN “ALL-REFRIGERATOR”
1. Press and hold Power button for approximately 3 seconds to turn unit OFF.
2. Close the main valve on the CO
2
cylinder.
3. Close the secondary shut-off valve on the regulator pipe.
4. Close the connection between the beer keg and the keg tapper.
5. Drain any remaining beer from the lines.
6. Disconnect the beer line and CO
2
air line from the keg coupler.
7. Remove the beer keg.
8. Remove the keg coupler.
9. Disconnect the air line from the CO
2
cylinder.
10. Remove the CO
2
air line from cabinet plug.
11. Replace the air line rear cabinet plug
12. Remove the beer tower. Also pull the beer line thru the top of the cabinet.
13. Replace the top cabinet plug.
14. Adjust temperature as desired.
REVERSING THE DOOR SWING
The door on models SBC677BI and SBC678OS is reversible door. As delivered, the door
is right-hinged. If you wish to reverse the hinge, a left-hand hinge kit is included.
14
CLEANING AND MAINTENANCE
Disconnect the power supply
Do not use coarse or abrasive cleaning agents as you can damage the surface of the
appliance.
before cleaning the appliance.
Periodic cleaning of the beer dispenser is necessary.
Every now and then, wipe the walls and bottom of the beer dispenser. Use a soft
nonmetallic brush or vacuum cleaner.
To clean the cabinet inside and out, mix 2 tablespoons of baking soda with 1 quart
warm water, or use a mild detergent.
Do not put drip tray in the dishwasher
Vacuum the tubing on the back of the unit twice a year.
(it is not dishwasher safe).
To provide protective care of a painted finish
Regular applications of wax or polish provide vital protection against rust. Waxing
cleans the surface and seals out moisture and other contaminants.
:
Use a wax polish that is suitable for appliances.
Apply the wax or polish when the beer dispenser is new and then at least twice a
year.
Door Gasket Cleaning
Clean the door gasket with a damp cloth every three months. The gasket must be
kept clean and pliable to ensure a proper seal.
:
Petroleum jelly applied lightly to the hinge side of the gasket will keep the gasket
pliable and ensure a good seal.
Cleaning behind the Beer Dispenser
We recommend that you clean the rear of the beer dispenser
:
at least twice a year
Use a vacuum or brush to clean the coils.
.
NOTE: Some operating environments may require more frequent cleaning.
Stainless steel doors (on some models) can be cleaned with a commercially available
stainless steel cleaner.
Do not use appliance wax or polish on stainless steel
Do not wipe the door with a soiled dish cloth or wet towel. These may leave a residue.
.
Use stainless steel cleaner only on stainless steel surfaces.
Dry with a soft cloth.
Storage
If the beer dispenser will not be in use for a long period of time, it should be stored.
Disconnect the unit from the power supply by removing the plug from the wall socket.
Defrost, clean and dry the inside. Leave the door open to prevent any unpleasant
smells from building up while the appliance is not in use.
CAUTION: Store the unit in such a way that children will not play with it. There is a
danger of child entrapment within the unit!
15
PROBLEMS WITH THE BEER
Problem
Cause
Correction
Beer is cloudy: The
beer in the glass
appears hazy and
not clear.
Excessively low
temperatures
may cause hazy
or cloudy beer,
particularly
when the beer
lies in the cold
coil for long
periods of time.
Drain a few ounces before drinking.
Raise the temperature setting of the unit.
Glasses may
not have been
cleaned
properly.
Do not wash beer glasses together with glasses
that have contained milk or any other fatty
substance. An excessive amount of germicide
build-up may also leave a fatty film, which will
cause beer to go flat.
It is
preferable to steam and sterilize glasses
where health laws permit.
Wash glasses thoroughly with a good detergent
to remove all fatty substances (i.e., lipstick)
Do not use soap.
Do not wipe the glasses dry. Permit glasses to
air-dry by placing them on a wire rack or on a
corrugated metal sheet.
Rinse the glasses in fresh cold water just before
serving beer. Serve beer in a wet glass.
Improper
drawing of beer
into glass
Open the faucet quickly and completely; proper
foam should be a tight creamy head. The collar
on the average glass should be ¾" to 1" high.
Beer drawn without a head has the appearance
of being flat.
Not enough
pressure
Increase the pressure if beer runs too slowly.
The correct flow should fill a 10-oz glass in 4
seconds (
approx. 8 oz of liquid). Check the
pressure source to determine whether there are
obstructions in the air line. Replace a sluggish air
source or the CO
2
regulator and gauge. The tank
pressure must always be higher than the
pressure used on the keg. Always apply
pressure to the keg before drawing beer.
Beer has off taste:
Often bitter and
bite-y; sometimes
completely lacking
flavor and zest. It
may also have an
oily or foul odor
along with an
unpleasant taste.
Improper
cleaning of the
tap
Brush and clean th
e tap properly. It should be
scoured using a detergent, then rinsed clean.
Contaminated
air line
Beer tube should be examined. If contaminated,
it should be replaced.
16
Condensation is
forming on faucet.
It is normal to
see conden-
sation forming
on the faucet. It
is caused by a
difference in
temperature
between the
cold beer and
the surfaces of
the faucet when
beer is flowing
through the line.
Beer that is left
in the faucet is
not cooled by
the
beer
dispenser.
After a period of non-use, a few ounces should
be drained before drinking.
TROUBLESHOOTING
You can solve many common Beer Dispenser problems easily, saving you the cost of
a possible service call. Try the suggestions below to see if you can solve the problem
before calling the servicer.
PROBLEM POSSIBLE CAUSE
The unit is not working
- Check that the plug is inserted correctly into the wall
socket.
- Check that there is power to the wall socket by
plugging in another appliance.
- Check the fuse.
The unit is noisy when running
-
Check to make sure that the cooler is level and it is not
in contact with another appliance or furniture.
NOTE: A gentle trickling sound is normal; this is likely
coolant in the sealed system or condensate water
from the unit.
The unit does not cool
sufficiently
- If the door has been opened too often, or it has been
left open for a while it will take time for the cooler to
reach its set temperature.
- Check that the airflow from the rear of the cooler has
not been reduced or obstructed due to insufficient
clearance.
17
LIMITED WARRANTY
Within the 48 contiguous United States, for one year from the date of purchase, when this appliance is operated and
maintained according to instructions attached to or furnished with the product, warrantor will pay for factory-specified parts
and repair labor to correct defects in materials or workmanship. Service must be provided by a designated service company.
Outside the 48 states, all parts are warranted for one year from manufacturing defects. Plastic parts, shelves and cabinets
are warranted to be manufactured to commercially acceptable standards, and are not covered from damage during handling
or breakage.
ONE-YEAR LIMITED WARRANTY
1. The compressor is covered for 5 years.
5-YEARS COMPRESSOR WARRANTY
2. Replacement does not include labor.
ITEMS WARRANTOR WILL NOT PAY FOR:
1. Service calls to correct the installation of your appliance, to instruct you how to use your appliance,
to replace or repair fuses or to correct wiring or plumbing.
2. Service calls to repair or replace appliance light bulbs or broken shelves. Consumable parts (such
as filters) are excluded from warranty coverage.
3. Damage resulting from accident, alteration, misuse, abuse, fire, flood, acts of God, improper
installation, installation not in accordance with electrical or plumbing codes, or use of products not
approved by warrantor.
4. Replacement parts or repair labor costs for units operated outside the United States.
5. Repairs to parts or systems resulting from unauthorized modifications made to the appliance.
6. Expenses for travel and transportation for product service in remote locations.
7. The removal and reinstallation of your appliance if it is installed in an inaccessible location or is not
installed in accordance with published installation instructions.
CUSTOMER'S SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE
PRODUCT REPAIR AS PROVIDED HEREIN. IMPLIED WARRANTIES, INCLUDING WARRANTIES
OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO ONE
YEAR. WARRANTOR SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL
DAMAGES. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL
OR CONSEQUENTIAL DAMAGES, OR LIMITATIONS ON THE DURATION OF IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS, SO THESE EXCLUSIONS OR LIMITATIONS
MAY NOT APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU
MAY ALSO HAVE OTHER RIGHTS, WHICH VARY FROM STATE TO STATE.
DISCLAIMER OF IMPLIED WARRANTIES – LIMITATION OF REMEDIES
WARNING! This product may contain chemicals known to the state of California to cause
cancer or birth defects or other reproductive harm. For more information, visit:
www.summitappliance.com/prop65
Chemicals known by the manufacturer to be present in this product in concentrations higher
than threshold limits: NONE.
.
FELIX STORCH, INC.
770 Garrison Avenue
Bronx, NY 10474
Phone: (718) 893-3900
Fax: (844) 478-8799
www.summitappliance.com
For parts and accessory ordering,
troubleshooting and helpful hints, visit:
www.summitappliance.com/support
Printed in China
18
TABLE DES MATIÈRES
Informations de sécurité importantes .................................................................. 19 - 22
Mise en place et installation .................................................................................... 23 - 29
Emplacement ........................................................................................................................ 23
Accessoires ........................................................................................................................... 23
Emplacement des pièces ................................................................................................. 24
Dimensions de l'installation encastrée (Modèle SBC677BI) ................ 24 - 25
Installation autoportante (Modèle SBC678OS) ........................................... 25
Installation du fût à bière .................................................................................................. 25
Guide des roulettes ............................................................................................................ 25
Installation du support de cylindre de CO
2
.................................................................. 26
Cylindre et détendeur de CO
2
.......................................................................................... 26
Installation de la conduite d'alimentation d'air de CO
2
au détendeur ............. 26
Installation du système de refroidissement ................................................................. 27
Installation de la colonne à bière .................................................................................. 27
Installation de la plaque protectrice en métal .......................................................... 27
Installation du fût à bière .................................................................................................. 27
Installation de la tête de soutirage .................................................................................. 28
Comment mettre en perce un fût à bière ................................................................... 28
Ouverture de la vanne principale du cylindre de CO
2
............................................. 28
Réglage du détendeur de CO
2
....................................................................................... 29
Levier de robinet en plastique ........................................................................................ 29
Rail de protection ................................................................................................................ 29
Distribution de la bière ...................................................................................................... 30
Fonctionnement .......................................................................................................... 30 – 31
Panneau de commande ................................................................................................... 30
Dégivrage ............................................................................................................................... 31
Conversion en un système « Réfrigérateur » ............................................................ 31
Inversion du sens d'ouverture de la porte .................................................................. 31
Nettoyage et entretien ........................................................................................................ 32
Problèmes avec la bière ............................................................................................ 33 - 34
Dépannage ............................................................................................................................. 34
Garantie limitée .................................................................................................................... 35
19
Merci d'avoir acheté ce refroidisseur de fût. Pour vous assurer d'obtenir les meilleurs
résultats de votre nouveau refroidisseur, veuillez prendre le temps de lire les
instructions de ce manuel.
INFORMATIONS DE SÉCURITÉ IMPORTANTES
AVERTISSEMENT!
Pour réduire le risque d'incendie, de décharge électrique ou de blessures
lors de l'utilisation de cet appareil, veuillez suivre ces précautions de base :
1. Lire toutes les instructions avant d'utiliser l'appareil.
2. L'appareil doit être correctement branché à la source d'alimentation électrique.
3. Remplacer immédiatement les cordons d'alimentation usés, fiches lâches et prises
de courant défectueuses.
4. Ne pas utiliser votre appareil en présence de vapeurs explosives.
5. Débrancher l'appareil de la source d'alimentation électrique avant de le nettoyer ou de le
réparer. Les réparations doivent être effectuées seulement par un technicien qualifié.
6. Ne jamais monter sur le dessus ou à l'intérieur de cet appareil ni se balancer sur la
porte
7. Afin de réduire les risques de blessure,
. Éviter de mettre du poids sur le dessus de l'appareil.
ne pas laisser les enfants jouer avec cet
appareil
8. Ne pas faire fonctionner la commande de la vanne, à moins que le cylindre de CO
2
soit entièrement installé et connecté.
.
9. Ne pas tenter de réparer ou de remplacer toute pièce sauf si cela est recommandé
dans le Manuel du propriétaire. Laisser les autres questions de service au
personnel technique qualifié.
10. Garder les matières d'emballage hors de la portée des enfants, car ils pourraient
provoquer la suffocation.
11. Ne pas pulvériser, ou rincer la fontaine à bière avec de l'eau, et éviter de la garder
dans un endroit humide, car cela pourrait endommager l'isolant électrique.
12. L'appareil n'est pas destiné à être utilisé par de jeunes enfants ou des personnes à
mobilité réduite sans supervision. Les jeunes enfants doivent être surveillés afin
d'assurer qu'ils ne jouent pas avec l'appareil.
REMARQUE : Cet appareil doit être utilisé uniquement pour son usage prévu.
DANGER! Risque de coincement pour les enfants!
Le coincement et la suffocation des enfants ne sont pas des problèmes du passé.
Les appareils jetés ou abandonnés sont encore dangereux, même s'ils ne feront
que « passer quelques jours sur le trottoir ».
Avant de jeter votre ancien appareil :
• Retirer la porte.
• Laisser les étagères en place afin que les enfants ne puissent pas
facilement grimper à l'intérieur.
• Cet appareil est exempt de CFC et de HFC et contient de petites quantités
d'isobutane (R600a), qui est respectueux de l'environnement, mais inflammable. Il
ne porte pas atteinte à la couche d'ozone ni n'augmente l'effet de serre. Pendant le
transport et l'installation de l'appareil, il faut veiller à ce qu'aucune partie du
système de refroidissement ne soit endommagée. Une fuite de liquide de
refroidissement peut s'enflammer et peut endommager les yeux.
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
Summit SBC677BINK Manuel utilisateur
- Taper
- Manuel utilisateur
- Ce manuel convient également à
dans d''autres langues
- English: Summit SBC677BINK User manual
Documents connexes
Autres documents
-
Nostalgia Electrics KRS-6100SS Mode d'emploi
-
Igloo FR329 Operating Instructions Manual
-
Sears 183.91579 Manuel utilisateur
-
Haier BrewMaster HBF05E Manuel utilisateur
-
-
Haier BrewMaster HBF205E Manuel utilisateur
-
Danby DKC5811BSL Le manuel du propriétaire
-
-
Danby DKC052BSLDB Manuel utilisateur
-
Hkoenig BW1890 Manuel utilisateur