Quality

•

Innovation

•

Style

User Manual

HBF205E

Guide de l’Utilisateur

HBF205E

Manual del Usuario Modelo

HBF205E

Dual Tap Beer Dispenser BrewMaster

1. Use this appliance only for its intended purpose as described in this

operation manual.

2. This appliance must be properly installed in accordance with the installation

instructions before it is used. See the installation section for more details.

3. This appliance must be connected to a proper electrical outlet with the

correct electrical supply.

4. Proper grounding must be ensured to reduce the risk of shock and fire. Do

not cut or remove the grounding plug! If you do not have a three-prong

electric receptacle outlet in the wall, have a certified electrician install the

8. Unplug your appliance before cleaning or making any repairs.

9. We suggest that a certified technician perform the service if for any reason

this product requires service.

10. If your old appliance is being discarded, we recommend that you remove the

door and leave the shelves in place. This will reduce the possibility of danger

to children.

11. This appliance should not be recessed or built into an enclosed cabinet. It is

designed for freestanding installation only.

12. Do not operate your appliance in the presence of explosive fumes.

13. Do not tamper with the controls.

18. To reduce the risk of injury, do not allow children to play in or on the

appliance. Close supervision is necessary when the appliance is used near

children.

1

Important Safety Precautions of CO2 (Carbon Dioxide) Gas

1. CO2 gas can be dangerous! CO2 cylinders contain high-pressure

compressed gas, which can be hazardous if not handled properly. Make sure

you read and understand all the procedures for the CO2 cylinders before

5. Never drop or throw a CO

6. Always keep CO2 cylinders away from heat. Store extra cylinders in a cool

place (preferably 70˚ F). Securely fasten with a chain in an upright position

when storing.

7. Always ventilate and leave the area immediately if CO2 leakage has

8. Always check the D.O.T. (Department of Transport) test date on the cylinder

SAVE THESE INSTRUCTIONS

FOR FUTURE USE

open when children are near the dispenser.

3

SAFETY PRECAUTIONS .....................................................................1-2

General Safety .....................................................................................1

CO2 (Carbon Dioxide) Gas Safety ........................................................2

UNPACKING AND ACCESSORIES INVENTORY ...............................4

PARTS AND FEATURES .....................................................................5

PROPER LOCATION ..........................................................................

6

Installing the CO2 Regulator and CO2 Cylinder.....................................8

Tapping the Beer Keg (Single-Valve Type Barrel) ....................................9

Important Safety Message for Draft Beer Dispensing .............................10

OPERATING YOUR BEER DISPENSER ..............................................10-11

Dispensing the Beer .............................................................................11

Understanding Beer Temperature..........................................................11

Understanding the Temperature Control Setting ....................................11

Normal Operating Sounds ...................................................................11

BEER SERVING GUIDE .....................................................................12-13

Beer Serving Tips .................................................................................12

14

PROPER CARE AND CLEANING OF THE BEER DISPENSER ............15-16

Installing the Cleaning Kit ....................................................................15

Cleaning and General Maintenance .....................................................16

TROUBLESHOOTING GUIDE ...........................................................17-20

WARRANTY .......................................................................................21

Page

1. Remove all packing materials. This includes the foam base and all adhesive

tape holding the accessories both inside and outside.

reference. If you find any accessories that are not in good condition or are

missing, please contact our customer service department for assistance. Our

Toll-Free number is 1-877-337-3639.

2 Keg Couplers (Beer Taps), Low Profile Type

1 CO2 Regulator, Dual Gauge, Dual Outlet•

1 CO2 Cylinder, 5 lbs.

1 Cleaning Kit, Including: 32 Ounce Bottle With Cap

4 Ounce Powder Cleaner

Faucet / Line Cleaning Brush

5

7

2. Insert the casters into the holes on the bottom

corners of the cabinet. Tighten each caster by

turning the nut clockwise with the wrench provided.

3. Once all four casters have been tightened evenly, stand the cabinet in an

upright position.

Installing the Beer Tap

Follow the steps below to install the beer tap.

1. First, remove the cabinet tap hole cover

located on the worktop. Firmly grasp

bottom of the draft arm.

3. Pass the beer tubes through the gasket

to the base of the draft arm.

4. Push both the hoses and the beer hose

through the hole in the worktop until

the draft arm is resting on top of the

cabinet.

5. Align the holes of the draft arm with the gasket and pilot holes on the worktop

of cabinet. Make sure that the faucets are facing the front.

Handle

pilot holes

3. Secure the guardrail to the cabinet with eight

small Phillips-Head screws.

Installation Instructions

Note: Your CO2 cylinder is shipped empty to avoid any possible accidents

Tapping the Beer Keg (American Sankey Type Barrel)

Your beer dispenser comes with “Lo-Boy Sankey Coupler American Type.”

1. (1) CO2 Regulator – dual gauge – dual outlet

2. (1) CO2 Tank – 5 pound - EMPTY

3. (2) Keg couplers – low profile type (Lo-Boy Sankey Coupler American

Type)

4. (4) White plastic squeeze clamps

5. (2) 4 foot long red hose

6. (1) Cleaning kit

BE SURE THAT BEFORE INSTALLATION YOU HAVE FILLED YOUR

TANK WITH GAS

15

For your convenience, this beer dispenser can be converted to a beverage cooler

application. Simply follow the steps below for a quick and easy conversion.

Note: When using as a beverage cooler, we do not recommend the use of

1. Close the main valve on the CO2 cylinder.

2. Close the connection between the beer keg and the keg coupler by pulling

and lifting the handle of the keg coupler into an upright position.

3. Disconnect both the beer line and the CO2 gas line from the keg coupler.

9. Install the cabinet tap hole cover on the worktop.

10. Lay the unit down sideways. We recommend that you place a piece of

cardboard or cloth underneath the cabinet to avoid dents or scratches to the

cabinet. Remove the casters and install leveling legs.

11. Install the two wire shelves.

A. Insert one end of each support pin into the holes on the right side of the

B. Place one end of the wire shelf into the left side of the cabinet and rest the

16

Follow the energy-saving tips below for optimum efficiency.

• Limit the opening and closing of the door on hot and humid days. When you

• Check regularly for proper air circulation around the unit to make sure that the

• Keep the door gasket clean and straight to ensure a proper seal. If the door

17

1. Mix one gallon of warm water and one ounce of

cleaner in a bucket. DO NOT USE SOAP.

2. Remove the cleaner cap assembly, fill the jar and

reassemble. Leave the remaining solution in the

bucket.

3. Turn off the air cock on the regulator and turn off

the valve on the CO2 tank.

4. Disconnect the keg coupler from the keg and then

disconnect the beer line from the tap.

5. Remove the faucet from the draft tower with the wench provided and attach

flows into the bucket.

8. Rinse the keg couple in the bucket with the remaining solution and then in

the bucket with the clean water.

9. Remove the cleaning fitting from the tower and replace the faucet. Make

sure the washer is in the back of the faucet.

10. Reattach the beer hose to the keg coupler and attach the keg coupler to the

keg.

Repeat the process for the additional tap system.

18

General Interior and Exterior Cabinet Cleaning

1. Prepare a cleaning solution of 3-4 tablespoons of baking soda mixed with

Door Gasket Cleaning

1. Clean the door gasket with a damp cloth every three months. The gasket must

be kept clean and pliable to ensure a proper seal.

2. Petroleum jelly applied lightly to the hinge side of the gaskets will keep the

gasket pliable and ensure a good seal.

Cleaning Behind the Beer Dispenser

1. We recommend that you clean the rear of the refrigerator at least twice a year.

Note: Some operating environments may require more frequent cleaning.

2. Use a vacuum or a brush to clean the coils.

19

1. Close tank drum valve by turning clockwise.

2. Unscrew adjustment Set Screw (counter-clockwise) as far as it will go and close

shut off valve.

3. Remove regulator from empty tank.

4. Remove dust cap from the new full tank. Open and close drum valve quickly

to blow of the dust from the outlet.

5. With drum valve in closed position, reattach regulator to the tank. Be sure to

check the washer, which is pre-installed on the C02 regulator.

6. Open drum valve all the way. (This is important because this drum valve seals

in two places.)

is appx. 17-1/2 lbs.