Rointe Elba LCD digital electric Le manuel du propriétaire

Elba electric digital

Models / Modelos / Modèle / Modellen

DIGITAL 400 | 450 | 500 | 550

MANUAL DE INSTALACIÓN Y USO

Página 22

MANUAL DE INSTALAÇÃO E UTILIZAÇÃO

Página 42

ES

PT

INSTRUCTIONS & INSTALLATION GUIDE

Page 02

EN

INSTALLATIE- EN GEBRUIKERSHANDLEIDING

Bladzijde 82

NL

MANUEL D’INSTALLATION ET D’UTILISATION

Page 62

FR

2

Installation & safety precautions (EN 60335 Standards)

Before switching on the product, please read the “Installation & Safety Precautions” in detail rst to

ensure the correct operation of the product.

Installation precautions

The product is designed for household or residential use. You are advised to have the product installed

by an authorized professional installer. Make sure the product is properly connected to 230V.

ATTENTION

Children under 3 years of age should be kept out of reach of the appliance

unless continuously supervised. Children from the age of 3 years to 8

years should only switch the appliance on/off when it has been placed

or installed in its normal intended use position and when they have been

given supervision or instruction concerning use of the appliance in a safe

way and understand the hazards involved. Children from 3 years of age to

8 years of age should not plug in, adjust or clean the appliance or carry out

maintenance operations.

This appliance can be used by children aged from 8 years and above

and persons with reduced physical sensory or mental capabilities or lack

of experience and knowledge if they are supervised or have been given

instruction concerning use of the appliance in a safe way and understand

the hazards involved. Children should not play with the appliance. Cleaning

and user maintenance should not be carried out by children without

supervision. Children must be supervised at all times to ensure that they

do not interfere with the product.

This product is lled with a precise amount of special oil that does not

need any maintenance. Any repairs requiring the opening of the oil tank

must only be done by an ofcial Rointe installer or its after-sales service

personnel, who should also be notied should an oil leak be noticed. The

regulations on discarding oil when the heater is being disposed of must be

observed.

Do not cut the power supply cable under any circumstances in order to

avoid electrical risks and to guarantee the correct operation of the towel

rail.

Do not switch on the product if you notice any external damage when

unpacking or installing the towel rail. If the power cable is damaged, it

must be replaced by the manufacturer, its after-sales service or authorized

personnel in order to avoid any damage.

3

ELBA DIGITAL

EN

Do not spray or wet the product. During operation, keep the product away

from combustible materials such as curtains, furniture, etc. Do not place

anything other than clothes, towels or non-ammable fabrics on the product.

The towel rail must be installed in such a way that the power plug is always

accessible. The power cable must never be in contact with the product

during operation.

CAUTION - Never touch the product with wet hands or any wet

body parts.

CAUTION - Some parts of this product may become very hot

and cause burns. Particular care should be taken when children

and vulnerable persons are present.

Contents

1. Rointe towel rails technical specications .............................................................................................4

2. Rointe towel rails installation........ ...........................................................................................................8

2.1. Mounting ..........................................................................................................................................8

2.2. Fixing the supports .........................................................................................................................9

2.3. Connecting instructions .................................................................................................................9

3. Rointe towel rails information & instructions..........................................................................................10

3.1. Keypad .............................................................................................................................................10

3.2. Screen ..............................................................................................................................................10

3.3. Switch on & off (stand-by) ..............................................................................................................11

3.4. Adjust the day & time ......................................................................................................................11

3.5. Lock the keypad...............................................................................................................................12

3.6. Select either MANUAL or AUTOMATIC mode.............................................................................12

3.7. Rointe towel rails advanced functions..................................................................................................15

4. Maintenance & cleaning............... .........................................................................................................16

5. Guarantee......................................... ......................................................................................................17

6. How to register your guarantee....... .......................................................................................................19

7. ERP Directive (EU) 2015/1188....... ..........................................................................................................20

4

1. Technical speciﬁcations (Models 400, 450, 500 & 550)

MODEL - Width 400

WHITE

TELL*40B077 TELL*40B112 TELL*40B150 TELL*40B172

CHROME

TELL*40C077 TELL*40C112 TELL*40C150 TELL*40C172

DIMENSIONS

Width (mm) 400 400 400 400

Height with control panel (mm) 863 1,213 1,593 1,813

Depth (mm) 50 50 50 50

Installed depth (mm) 100 100 100 100

MECHANICAL CHARACTERISTICS

Stainless steel heating element

   

Thermal ﬂuid

   

Digital control panel

   

LCD screen

   

Finish

White RAL 9016

Chrome

ELECTRICAL CHARACTERISTICS

Nominal power (W)

White 300 500 750 1,000

Chrome 300 300 500 750

Voltage (V) 230 V ~ 230 V ~ 230 V ~ 230 V ~

Current (A)

White 1.3 2.2 3.3 4.4

Chrome 1.3 1.3 2.2 3.3

Class II

   

SAFETY & INSTALLATION

Installation kit included

   

Safety thermostat

   

Fireproof wiring

   

Protection grade IP 44 IP 44 IP 44 IP 44

5

ELBA DIGITAL

EN

MODEL - Width 450

WHITE

TELL*45B077 TELL*45B112 TELL*45B150 TELL*45B172

CHROME

TELL*45C077 TELL*45C112 TELL*45C150 TELL*45C172

DIMENSIONS

Width (mm) 450 450 450 450

Height with control panel (mm) 863 1,213 1,593 1,813

Depth (mm) 50 50 50 50

Installed depth (mm) 100 100 100 100

MECHANICAL CHARACTERISTICS

Stainless steel heating element

   

Thermal ﬂuid

   

Digital control panel

   

LCD screen

   

Finish

White RAL 9016

Chrome

ELECTRICAL CHARACTERISTICS

Nominal power (W)

White 300 500 750 1,000

Chrome 300 300 500 750

Voltage (V) 230 V ~ 230 V ~ 230 V ~ 230 V ~

Current (A)

White 1.3 2.2 3.3 4.4

Chrome 1.3 1.3 2.2 3.3

Class II

   

SAFETY & INSTALLATION

Installation kit included

   

Safety thermostat

   

Fireproof wiring

   

Protection grade IP 44 IP 44 IP 44 IP 44

6

MODEL - Width 500

WHITE

TELL*50B077 TELL*50B112 TELL*50B150 TELL*50B172

CHROME

TELL*50C077 TELL*50C112 TELL*50C150 TELL*50C172

DIMENSIONS

Width (mm) 500 500 500 500

Height with control panel (mm) 863 1,213 1,593 1,813

Depth (mm) 50 50 50 50

Installed depth (mm) 100 100 100 100

MECHANICAL CHARACTERISTICS

Stainless steel heating element

   

Thermal ﬂuid

   

Digital control panel

   

LCD screen

   

Finish

White RAL 9016

Chrome

ELECTRICAL CHARACTERISTICS

Nominal power (W)

White 300 500 750 1,000

Chrome 300 300 500 750

Voltage (V) 230 V ~ 230 V ~ 230 V ~ 230 V ~

Current (A)

White 1.3 2.2 3.3 4.4

Chrome 1.3 1.3 2.2 3.3

Class II

   

SAFETY & INSTALLATION

Installation kit included

   

Safety thermostat

   

Fireproof wiring

   

Protection grade IP 44 IP 44 IP 44 IP 44

7

ELBA DIGITAL

EN

MODEL - Width 550

WHITE

TELL*55B077 TELL*55B112 TELL*55B155 TELL*55B172

CHROME

TELL*55C077 TELL*55C112 TELL*55C155 TELL*55C172

DIMENSIONS

Width (mm) 550 550 550 550

Height with control panel (mm) 863 1,213 1,593 1,813

Depth (mm) 50 50 50 50

Installed depth (mm) 100 100 100 100

MECHANICAL CHARACTERISTICS

Stainless steel heating element

   

Thermal ﬂuid

   

Digital control panel

   

LCD screen

   

Finish

White RAL 9016

Chrome

ELECTRICAL CHARACTERISTICS

Nominal power (W)

White 300 500 750 1,000

Chrome 300 300 500 750

Voltage (V) 230 V ~ 230 V ~ 230 V ~ 230 V ~

Current (A)

White 1.3 2.2 3.3 4.4

Chrome 1.3 1.3 2.2 3.3

Class II

   

SAFETY & INSTALLATION

Installation kit included

   

Safety thermostat

   

Fireproof wiring

   

Protection grade IP 44 IP 44 IP 44 IP 44

8

2. Rointe towel rails installation

2.1. Mounting instructions

Inside the packaging you will nd a xing kit. Please nd the instructions below:

1. Choose the right part of the wall.

2. Place the mounting stencil on the wall, marking the places for the holes.

3. Remove the stencil and make the holes in the wall.

4. Insert the rawl plugs in the holes made.

5. Screw the plastic fastener to the wall with the 5.5 x 50 mm screw.

6. Screw the two brackets for supporting the product and the plastic fastener to the horizontal tube

of the product like in Figure 1 with the 8 x 26 mm screw.

7. Insert what you have assembled in Section 6 into the plastic piece. Fix well with the 5 x 12 mm screw.

8. Place the cover on the piece supporting the product.

NO. ELEMENT

1 10 x 40 mm Rawl Plug

2 Bracket

3 5.5 x 50 mm Screw

4 5 x 12 mm Screw

5 Bracket Insert

6 Bracket Head

7 8 x 26 mm Screw

8 Cap

9 Product

2.2. Connecting instructions

Connection to the mains must be made observing the voltage stated on the product technical data label.

This product is designed to be permanently installed connected to xed facilities. The product power

supply circuit must have an all-pole circuit breaker switch with a separation of at least 3 mm between

the contacts. The product must be installed, if possible, away from any source of draughts (windows,

doors) or any other thing which may affect its functioning. In this way, the temperature will not be

affected. Place any object which might prevent the air ow (furniture, armchairs) 50 cm away from the

front of the product.The product must never be installed immediately below a power point. The lower

part of the control panel must be placed at least 15 cm from the oor.

For any product, if the power cable is damaged, it must be replaced by a specic cable. The replacement

of the cable must be done by the maker, its after-sales service or qualied personnel. The technical

specications of your product appear on the technical data label.

1

5

9

ELBA DIGITAL

EN

OK

IMPORTANT - This product must never be installed with its control

panel at the top. This product must not be installed horizontally. During

installation, use wedges so that the control panel will not be in contact

with the ﬂoor.

2.3. Speciﬁc regulations for bathrooms

This product is classied as CLASS II and can be safety installed in Zones 3. For installations in Zones

2 (check the scheme below), please consider the following limitations:

•

In bathrooms, the product must never be installed in such a way that the control panel may be touched

by someone in the bathtub or having a shower. The control panel should be located at least 600 mm

distance from any wet areas. The body of the product can be placed in Zones 2 if the control panel is

located inside Zone 3.

• In a kitchen or bathroom, the body of the product must be placed at least 25 cm from the oor.

10

3. Rointe towel rails information & instructions

3.1. Keypad

Settings / Back

Decrease temperature / Move down

On/Off (stand-by) / Conrm

Increase temperature / Move up

MANUAL / AUTO function

3.2. Screen

1 Programming - Hours of the Day available

2 Programming - Hours of the Day selected

3 Days of the Week

4 Energy Consumption indicator

5 SET TIME setting indicator

6 Current time/temperature

7 Keypad Locked indicator

8 Heating element on indicator

9 COMFORT / ECO / ANTI-FROST mode indicator

10 OPEN WINDOWS

11 Pre-installed programmes indicator

12 MANUAL/PILOT* function indicator

(*Not available)

13 Programming - COMFORT / ECO indicator

14 2 Hour Boost mode indicator

Keypad locked

Heating element on

ANTI-FROST mode on

ECO mode on

COMFORT mode on

OPEN WINDOWS function on

Pre-installed programme active

MANUAL function active

PILOT function active (Not available)

2 Hour Boost mode active

11

ELBA DIGITAL

EN

3.3. Switch on & off (stand-by)

To switch the product on, please press the button once. To switch the product off, please press

the button again.

When you switch the product on for the rst time you will be prompted to set the day and time. Use

the

buttons to select the correct hour and press the button to conrm. Next use the

buttons to select the correct minute and press the button to conrm. Then use the

buttons to select the correct day and press the button to conrm.

3.4. Adjust the day & time

To adjust the day or time of the product, please press the button to access the Settings Menu.

Then you will need to use the buttons to scroll to the menu on the screen and press

the button to conrm.

Use the

buttons to select the correct hour and press the button to conrm. Next use the

buttons to select the correct minute and press the button to conrm. Then use the

buttons to select the correct day and press the button to conrm.

3.5. Lock the keypad

To lock the keypad, please press and hold the buttons at the same time for 3 seconds. A

icon will appear at the top of the screen.

To unlock the keypad, press and hold the

buttons again at the same time for 3 seconds. The

icon will disappear from the top of the screen.

3.6. Select either the MANUAL, AUTOMATIC or PILOT mode*

(*only upon demand)

To select either the MANUAL, PILOT and AUTO, AUTO 1, AUTO 2, AUTO 3 and AUTO 4 modes you

need to press the button and keep pressing until the mode you want is highlighted.

On the display panel, the

icon will appear when you are in one of the AUTO modes (1-4), the

icon will appear when you are in MANUAL mode and the icon will appear when in PILOT mode

(not available).

12

00 01 02 03 04 05 06 07 08 09 10 11

AM

3.6.1. MANUAL mode

When MANUAL mode is selected the set temperature, MANUAL mode icon, COMFORT/ECO/AN-

TI-FROST icon and the time/day of the week will be displayed on the screen. The set temperature

and the hour will alternate every 5 seconds on the screen.

In MANUAL mode you can choose a set temperature and the corresponding COMFORT/ECO/AN-

TI-FROST icon will appear on the screen according to the ranges below:

COMFORT

21 - 30

o

C

ECO

7.5 – 20.5

o

C

ANTI-FROST

7

o

C

To adjust the set temperature:

Use the

buttons to either increase or decrease the temperature respectively. When you

choose a temperature in the table above, the corresponding icon will appear on the screen.

When the room temperature is lower than the set temperature on the display panel, the product will

display the

symbol in the top right of the screen.

3.6.2 AUTOMATIC mode

When the AUTOMATIC mode is selected, this activates the programming already established in the

product. You can choose from one of the 4 pre-installed programmes within the Rointe product:

Auto 1 Auto 2 Auto 3 Auto 4

You can also modify these pre-installed programmes to suit your needs. Please check the following

pages for a step by step guide on how to activate or modify one of the pre-installed programmes.

13

ELBA DIGITAL

EN

AUTO pre-installed programme scheduling

PREPROGRAM 1

0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23

Mon-

Fri

Sat-

Sun

PREPROGRAM 2

0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23

Mon-

Fri

Sat-

Sun

PREPROGRAM 3

0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23

Mon-

Sun

PREPROGRAM 4

0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23

Mon-

Fri

Sat-

Sun

To activate one of the pre-installed programmes:

Press the

button on the keypad until either AUTO, AUTO 1, AUTO 2, AUTO 3 or AUTO 4 is high-

lighted. The pre-installed programme will now be active and the corresponding icon will appear on

the screen.

1

A

00 01 02 03 04 05 06 07 08 09 10 11

AM

To modify one of the pre-installed programmes:

STEP 1 - You will need to establish the set temperature of the COMFORT/ECO/ANTI-FROST modes

rst. Please press the

button to access the Settings Menu. Then you will need to use the

buttons to scroll between the menus to select the menu on the screen and press

the button to conrm. The COMFORT temperature is adjusted rst. Press the buttons to

either increase or decrease the temperature respectively within the pre-set COMFORT temper-

ature range (see table above). Press the button to conrm and you will then move to the ECO

temperature settings. Use the buttons to either increase or decrease the temperature

COMFORT ECO OFF

14

respectively within the pre-set ECO temperature range. Press the button to conrm and you will

then move to the ANTI-FROST temperature settings. Use the buttons to either increase

or decrease the temperature respectively and press the button to conrm.

STEP 2 - Press the button on the keypad until the programme that you wish to modify (AUTO 1,

AUTO 2, AUTO 3 or AUTO 4) is highlighted. The pre-installed programme will now be active and the

corresponding icon will appear on the screen.

STEP 3 - Press AND hold the

button on the keypad for 2 seconds to modify the hours and days.

The days can be modied rst. Use the buttons to select the chosen days and press the

button to select the days you want to modify.

1

A

STEP 4 - Then you will move onto setting the mode for each hour, of the day which will begin at 0h

(midnight). You will need to go through each hour and select a mode for each hour. Select the mode

by pressing the button - press once for COMFORT, press twice for ECO and press three times

for ANTI-FROST. To move onto the next hour, use the buttons.

NO-FROST ECO COMFORT

Once all 24 hours of the day have been assigned a mode, press the button to save your settings

and return to the main screen.

3.7. Rointe towel rails advanced functions

3.7.1. OPEN WINDOWS function

The Rointe towel rails have the OPEN WINDOWS function set to ON to begin with. This function

is activated when the temperature sensor detects a drop of 4ºC from the set temperature within a 30

minute time period.

15

ELBA DIGITAL

EN

The OPEN WINDOWS function will be active for 2 hours. When the OPEN WINDOWS function is

activated, the product will move into ANTI-FROST mode at 7ºC.

To activate or deactivate this function, please press the

button to access the Settings Menu.

Then you will need to use the buttons to select the OPEN WINDOWS. Once selected, press

the button and use the buttons to activate or deactivate this function.

The function PRESENCE DETECT (ALSO DISPLAYED IN THIS MENU) is not available on the

product.

3.7.3. Energy consumption indicator

Rointe towel rails have a unique energy consumption indicator so you can monitor your energy ex-

penditure. The



icon will appear down the left side of the screen when switched on to indicate the

expenditure level.

M

24.5 - 30ºC 19 - 24ºC < 19ºC

Within this temperature range,

you are using a high amount of

energy.

Within this temperature range,

you are using an average/me-

dium amount of energy.

Within this temperature range,

you are using a low amount of

energy.º

3.7.4. 2 HOUR BOOST function

This product has a unique two hour BOOST mode that will override any other set mode and will boost

your product to maximum power. You can choose to boost to maximum power for 15 minutes, 30

minutes, 1 hour or 2 hours.

To activate, press and hold the

button for 2 seconds. Use the buttons to select either 15

minutes, 30 minutes, 1 hour or 2 hour boost and conrm by pressing the button. To deactivate,

please press the button again once.

4. Maintenance & cleaning

The product does not require any type of maintenance. We recommend that all parts of the product

are kept clean (behind, underneath, upper ns, etc.). Do not use any abrasive product on the steel

main body. Clean it with a damp cloth and a pH neutral soap, and the control panel with a dry cloth.

European Directive 2012/19/UE

Under the European Directive 2012/19/UE on waste electrical and electronic equipment (WEEE), the

16

product cannot be disposed in the usual council bins and containers. They must be separated to

optimize the recovery and recycling of all of the components and materials and reducing the impact

to human health and the environment. The symbol of the container crossed out over a horizontal line

is marked on all of Rointe products to remind the consumer of the obligation to separate them on

disposal.

The consumer should contact the local authority or original point of sale to learn more about the

correct disposal of this product.

5. Guarantee

In this section, we hereby describe the guarantee conditions which the buyer acquires on buying a

new Rointe product. These conditions comply with all the rights construed in the national legislation

in force, as well as any additional rights and guarantees which are offered by Rointe.

5.1. Any incident that you might detect in your Rointe product can be sorted by the product seller or

quickly by the manufacturer. Please contact Rointe by telephoning (UK) 0203 321 5929 or (Ireland)

01 553 0523 for technical support. If you live in a different country, please check the correct phone

number on the back of this manual.

ELBA 500 300W

TELLN45B077

300 W

You will need to state the product reference (located on the label indicating product features), serial

number, proof of purchase and the type of incident at hand when contacting us so that we can check

the guarantee. In addition, please attach a copy of the product invoice.

5.2. Rointe guarantees that there are no material defects of design or manufacture at the time of

original acquisition and guarantees the steel main body for a period of 120 months and 24 months for

any electronic and electrical components.

5.3. If during the guarantee period, the product does not work correctly under normal use, and any

design, material or manufacturing defect is found, Rointe will repair or substitute the product as it

may see t, in accordance with the terms and conditions as follows:

5.3.1. The guarantee is only applicable if the original guarantee is issued by the seller and when

the said guarantee is lled in correctly including product reference, series number (marked on the

product’s label indicating technical features), purchase date and the seller’s stamp.

Rointe reserves the right to reject the guarantee service when this information has been removed or

modied after the original product purchase.

5.3.2. The guarantee only applies to those cases that concern material, design and manufacturing

defects, and under no circumstances covers damage to the product for the following reasons:

5.3.2.1 Incorrect use of the product, i.e. used for other purposes that are not construed as its

17

ELBA DIGITAL

EN

normal use or for not respecting the instructions of use and maintenance given by Rointe as well as

incorrect installation or use of the product that may not comply with the current technical standards

of safety.

Corrosion caused by direct exposure to salt water is excluded from the guarantee. When the product

is installed no more than 200m from the coast the guarantee for damages caused by corrosion the

period will be reduced by 50%.

5.3.2.2 Any unauthorized repairs carried out by unauthorized technicians or opening of the

product by unauthorized people.

5.3.2.3 Any accidents that are deemed outside the control of Rointe, such as lightning, res,

oods, public disorders, etc.

5.3.3. Any repairs or substitutions that are included in this guarantee do not allow any additions

or new periods of guarantee.

5.3.4. Any repairs or substitutions covered under this guarantee must be parts that are functional-

ly equivalent. The defective parts or parts removed or replaced shall become the property of Rointe.

5.4. The technical service of Rointe will advise you if you need to buy any parts not covered under

the guarantee or out of guarantee.

5.5. This guarantee does not affect the buyer’s legal rights stipulated in the current national legisla-

tion, nor affects those rights against the distributor or installer that could come forth in compliance

with the purchase contract.

5.6. In the absence of a national legal legislation applicable, this guarantee shall prevail and may be

construed as the buyer’s only protection. Rointe, its ofces, distributors and installers may not be

held responsible for any accidental damage that emerges due to infringement of any rules implicitly

related to this product.

18

6. How to register your product guarantee

IMPORTANT: It’s important to register your ROINTE product as part of our guarantee service, in

case you wish to make a claim.

You can register your ROINTE product in the following ways:

WEBSITE

1. Go to www.rointe.com/uk/register-your-guarantee/.

2. Login to your existing account or create a new account if you need to.

3. Click on “My products”.

4. Enter your product reference (alphanumeric and in upper case).

5. Enter your serial number (26 digits located on the metal tag on your product and starts with 843).

6. Upload your proof of purchase, such as invoice in PDF, JPEG or PNG format. This is not

mandatory but by doing so you ensure your guarantee period is accurate.

7. Click “Register”.

8. Congratulations! Your product is now registered.

EMAIL

1. Send an email to support@rointe.co.uk with the following information:

• Customer name

• Address and postcode

• Telephone number and email address

• Product reference (as described above)

• Serial number (as described above)

• Product purchase date and proof of purchase (as described above).

2. Our Technical Support team will conrm your product registration and request any additional

information needed via email.

POST

1. Post the information listed in the EMAIL section above to:

• INDUSTRIAS ROYAL TERMIC, S.L. t/a Rointe UK, C/E Parcela 43, 30140,

Santomera (SPAIN)

2. Please ensure you obtain proof of posting.

19

ELBA DIGITAL

EN

20

7. ERP DIRECTIVE (EU) 2015/1188

ITEM

White

SYMBOL UNIT

TELL***B077 TELL***B112 TELL***B150 TELL***B172

Chrome TELL***C077 TELL***C112 TELL***C150 TELL***C172

HEAT OUTPUT

Nominal heat output

White

P

nom kW 0.30 0.50 0.75 1.00

Chrome

P

nom kW 0.30 0.30 0.50 0.75

Minimal heat output

P

min kW n/a n/a n/a n/a

Maximum continuous heat output

White

P

max,c kW 0.30 0.50 0.75 1.00

Chrome

P

max,c kW 0.30 0.30 0.50 0.75

AUXILIARY ELECTRICITY CONSUMPTION

At nominal heat output

White

el

MAX kW 0.30 0.50 0.75 1.00

Chrome

el

MAX kW 0.30 0.30 0.50 0.75

At minimum heat output

White

el

MIN kW 0.30 0.50 0.75 1.00

Chrome

el

MIN kW 0.30 0.30 0.50 0.75

In standby mode

el

SB kW 0.002 0.002 0.002 0.002

La page charge ...

Rointe Elba LCD digital electric Le manuel du propriétaire

Ce manuel convient également à

Rointe Elba LCD digital electric Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents