Tripp Lite SU3000RTXL2U Le manuel du propriétaire

Owner’s Manual

SmartOnline

®

Rack/Tower On-Line UPS System

Model: SU3000RTXL2U

(Series Number: AG-013A)

Not suitable for mobile applications.

1. Overview 2

1.1 Package Contents 2

1.2 Optional Accessories 2

2. Important Safety Instructions 2

3. UPS Circuit Block Diagram 3

4. Installation 4

4.1 Mounting (Rack) 4

4.2 Mounting (Tower) 6

4.3 Connection and Start-Up 6

4.4 Optional Connections 7

5. Operation 10

5.1 Front Panel Switches 10

5.2 Advanced Operational 10

Settings

5.3 Power Strategy 11

Selection Options

5.4 Front Panel Indicator Lights 12

5.5 Rear Panel 13

5.6 Communications 14

5.7 Conﬁguring External 15

Battery Packs

5.8 Conﬁguration Options 16

via WEBCARDLX

6. Troubleshooting 19

7. Battery Replacement 20

8. Storage and Service 23

8.1 Storage 23

8.2 Service 23

9. Product Registration 23

Español 24

Français 48

PROTECT YOUR INVESTMENT!

Register your product for quicker service

and ultimate peace of mind.

You could also win an

ISOBAR6ULTRA surge protector—

a $100 value!

www.tripplite.com/warranty

1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support

®

is a trademark of Tripp Lite.

17-04-276 9335AA.indb 1 5/1/2017 1:24:27 PM

2

2. Important Safety Instructions

1. Overview

SAVE THESE INSTRUCTIONS

This manual contains instructions and warnings that should be followed during the

installation, operation and storage of all Tripp Lite UPS Systems. Failure to heed these

warnings may affect your warranty.

UPS Location Warnings

• Install the UPS indoors, away from excess moisture or heat, conductive contaminants, dust or

direct sunlight.

• For best performance, keep the indoor temperature between 32º F and 104º F

(0º C and 40º C).

• Leave adequate space around all sides of the UPS for proper ventilation.

• Do not mount unit with its front or rear panel facing down (at any angle). Mounting in this

manner will seriously inhibit the unit’s internal cooling, eventually causing product damage not

covered under warranty.

The Tripp Lite SmartOnline Rack/Tower System is an on-line, double-conversion UPS offering the

highest level of power protection. Delivering a clean sine wave output and with zero transfer time to

battery in the event of a utility failure, the UPS is suitable for all advanced networking applications.

Each system provides long running battery support with optional extended-run and SNMP/Web

communication ability. Built-in interfaces include USB, RS232 serial and Emergency Power Off

(EPO). The front panel display provides detailed UPS status including battery level and status,

operating mode and load level.

1.1 Package Contents

• UPS

• 4-Post Rail Kit

• Rack-Mount Ear Kit

• USB Cable

• RS232 Cable

• Owner’s Manual

1.2 Optional Accessories

• WEBCARDLX: Internal network interface card for SNMP/Web control and monitoring

• 2POSTRMKITWM: Supports rack-mount UPS and battery packs in 2-post rackmount or

wall-mount configurations

• 2-9USTAND: Supports rack-mount UPS and battery packs in an upright tower configuration

Visit the specification page for your UPS system at www.tripplite.com for detailed extended runtime

data and additional accessory options.

17-04-276 9335AA.indb 2 5/1/2017 1:24:28 PM

3

2. Important Safety Instructions

3. UPS Circuit Block Diagram

UPS Connection Warnings

• Connect the UPS directly to a properly grounded AC power outlet. Do not plug the UPS into

itself; this will damage the UPS.

• Do not modify the UPS plug, and do not use an adapter that would eliminate the UPS ground

connection.

• Do not use extension cords to connect the UPS to an AC outlet. Your warranty will be voided if

anything other than Tripp Lite surge protectors are used to connect the UPS to an outlet.

• If the UPS receives power from a motor-powered AC generator, the generator must provide

clean, filtered, computer-grade output.

• The mains socket outlet that supplies the UPS should be near the UPS and be easily accessible.

• To remove AC voltage from the UPS, pull the plug from the socket outlet.

Equipment Connection Warnings

• Use of this equipment in life support applications where failure of this equipment can reasonably

be expected to cause the failure of the life support equipment or to significantly affect its safety

or effectiveness is not recommended.

• Do not connect surge protectors or extension cords to the output of the UPS. This might damage

the UPS and may affect the surge protector and UPS warranties.

• Connect the UPS to an outlet that is adequately protected against excess currents, short circuits

and earth faults, as part of the building installation. The outlet protection for the UPS should be

in series with the mains input.

• To reduce the risk of fire, connect only to a circuit provided with 240V/120V 30A maximum

branch circuit overcurrent protection in accordance with the National Electrical Code

®

(NEC

®

),

ANSI/NFPA 70 or local electrical code. The circuit breaker must meet the rated short circuit

capacity of at least 1KA.

17-04-276 9335AA.indb 3 5/1/2017 1:24:28 PM

4

4. Installation

1

2

C

4.1 Mounting (Rack)

Mount your equipment in either a 4-post or 2-post rack or rack enclosure. The user must

determine the fitness of hardware and procedures before mounting. If hardware and procedures are

not suitable for your application, contact the manufacturer of your rack or rack enclosure. The

procedures described in this manual are for common rack and rack enclosure types and may not

be appropriate for all applications.

4-Post Mounting

1

The included plastic pegs

A

will temporarily support the empty rackmount shelves

B

while the

permanent mounting hardware is prepared. Insert a peg into the third hole from the top on the

front end of each bracket. On the rear end, insert a peg into the center hole. (Each front

bracket has 6 holes and each rear bracket has 5 holes.) The pegs will snap into place.

After installing the pegs, expand each shelf to match the depth of your rack rails. The pegs will

fit through the square holes in the rack rails to support the shelves. Refer to the rack unit

labels to confirm that the shelves are level in all directions.

Note: The support ledge of each shelf must face inward.

A

B

2

Remove the pegs at the front end of each bracket. Secure the shelves

B

to the mounting rails

permanently using the included screws and cup washers

C

as shown. Place 2 screws at the

front of each rail (4 total) and 2 screws at the back of each rail (4 total). Tighten all screws

before proceeding.

Note: The rear pegs may be left in for installation, but the front ones must be removed before the bracket is

secured by screws.

WARNING!

Do not attempt to install the UPS until the required screws have been inserted and

tightened. The plastic pegs will not support the weight of the UPS.

B

17-04-276 9335AA.indb 4 5/1/2017 1:24:30 PM

5

4. Installation

D

G

F

3

4

3

Attach the UPS mounting brackets

D

to the forward mounting holes

E

of the UPS using the

included hardware

F

. The mounting bracket “ears” should face forward.

E

4

With the aid of an assistant (if necessary), lift the UPS and slide it into the shelves. Attach the

UPS mounting brackets to the forward mounting rails with user-supplied screws and washers

G

. Tighten all screws securely.

2-Post Mounting

To mount 2U UPS models in 2-post racks, the addition of a Tripp Lite 2-Post Rack-mount

Installation Kit (model: 2POSTRMKITWM, sold separately) is required. See Installation Kit owner’s

manual for installation procedure.

17-04-276 9335AA.indb 5 5/1/2017 1:24:33 PM

6

1

2

4.2 Mounting (Tower)

The UPS can be mounted in an upright tower position

with optional base stands sold separately by Tripp Lite

(model: 2-9USTAND). When mounting the UPS on

adjustable base stands, make sure that the control

panel is toward the top. The control panel may be

rotated to make it easier to read. Remove the 4 front

screws from the front panel and take it off. Pinch the

tabs located on the sides of the LED panel, and rotate

it. Replace the front panel and secure it. Front panel

setup should be performed by service personnel only.

WARNING!

All UPS systems are extremely heavy. Use caution

when lifting and mounting. User must properly

stabilize the UPS when lifting and mounting.

4.3 Connection and Start-Up

1

Plug the UPS system into an

electrical outlet.

The UPS system must be connected to a

dedicated circuit of sufficient amperage. Refer to

the UPS system nameplate for input requirements.

Note: The UPS will pass unfiltered, unregulated power to

the outlets as soon as it is plugged in. Bypass is enabled

from the factory.

After the UPS system is plugged in, the following

sequence of events will occur:

1. The fan will turn on and all LEDs will

illuminate momentarily.

2. The percent level LEDs (25%, 50%, 75% and

100%) will illuminate one at a time.

3. The “LINE” and “LOAD” LEDs will

illuminate to indicate normal operation.

Voltage Note: The UPS system supports a nominal AC

voltage setting of 100V, 110V, 115V, 120V or 127V.

120V is the factory default setting. The full output

capacity of 2700 watts is available when the UPS system

is set at 120V or 127V. The output capacity is reduced

when the UPS is set to lower voltages: 2160 watts at

100V, 2295 watts at 110V, and 2430 watts at 115V. The

nominal voltage setting can be changed with the optional

WEBCARDLX internal accessory card. See the

WEBCARDLX documentation for more information about

changing the nominal voltage setting.

4. Installation

1

17-04-276 9335AA.indb 6 5/1/2017 1:24:34 PM

7

BP DETECTION

ACC. SLOT

USB

RS232

VCC

EPO

GND

EPO

72V 45A

- +

INPUT

OUTPUT

2

Plug equipment into the UPS

system’s AC outlets.

The UPS system is designed to support

computer equipment only. The UPS system will

become overloaded if household appliances or

laser printers are connected to its outlets.

4.4 Optional Connections

The UPS system will function properly without these connections.*

* Note: PowerAlert software (available as a FREE download at www.tripplite.com) or the optional WEBCARDLX

internal accessory card is required to control some of the advanced features of the UPS system, including

economy mode, nominal AC voltage settings and frequency conversion settings. The factory defaults are suitable

for most applications.

1

USB and RS232 Serial Communications

Use the included USB cable (see

1a

) or RS232 (DB9) serial cable (see

1b

) to connect the

UPS system’s communication port to a computer’s communication port. Install PowerAlert

software on the computer. (See the PowerAlert software documentation for system

requirements and installation instructions.)

4. Installation

2

3

Turn the UPS system ON.

To turn on the UPS system, press the “ON/TEST”

button for approximately 1 second until the UPS

system beeps, then release the button.

The UPS system will begin providing filtered,

regulated AC power to its outlets. The “ON LINE”

LED will illuminate.

Note: UPS system will function properly upon initial

startup; however, maximum runtime for the unit’s

battery will only be accessible after it has been charged

for 24 hours.

1a 1b

17-04-276 9335AA.indb 7 5/1/2017 1:24:37 PM

8

4. Installation

2

EPO Port Connection

This optional feature is only for those applications that require connection to a facility’s

Emergency Power Off (EPO) circuit. When the UPS is connected to this circuit, it enables

emergency shutdown of its inverter and inhibits transfer to internal bypass. A cable is required

to connect the EPO port of the UPS (see

2a

) to a normally closed or normally open switch

according to the circuit diagram (see

2b

). The cable and switch must be supplied by the user.

Notes:

1. The cable should not have a resistance of greater than 5 ohms.

2. If a non-latching EPO switch is used, the EPO must be held for a minimum of 1 second. This does not

apply to a latching EPO switch.

CAUTION: The EPO port is not a phone line surge suppressor; do not connect a phone

line to this port.

UPS Unit State when asserting EPO with AC line present:

LEDs Output Fans Serial SNMP USB

OFF OFF ON

(if in frequency

conversion

mode)

ON ON ON

To restart the UPS unit after asserting EPO with AC line present:

1. Verify the EPO assertion has been removed or cleared.

2. Press the ON button

3. Now the UPS will start back up in Bypass mode.

UPS Unit State when asserting EPO without AC line power:

LEDs Output Fans Serial SNMP USB

OFF OFF OFF OFF OFF OFF

To restart the UPS unit after asserting EPO without AC line power:

1. Verify the EPO assertion has been removed or cleared.

2. Reapply AC line power to the UPS unit. Now the UPS will start back up in Standby mode.

4-5

2a 2b

17-04-276 9335AA.indb 8 5/1/2017 1:24:39 PM

9

4. Installation

3

External Battery Connection

Check to ensure the external batteries being

connected match the voltage listed on the UPS

battery connector. Adding external batteries will

increase recharge time as well as runtime. See

the battery pack owner's manual for complete

installation instructions. Make sure cables are

fully inserted into their connectors. Small sparks

may result during battery connection; this is

normal. Do not connect or disconnect battery

packs when the UPS is running on battery power.

Tripp Lite SMART Battery Packs include a wired

data connection that enables automatic detection

and configuration for up to 6 SMART Battery

Packs to the UPS. Tripp Lite Legacy NON-SMART

battery packs are also supported for extended

runtime applications. For External battery

configuration, see Section 5.7: Configuring

External Battery Packs for options and

configuration methods.

4

Accessory Card Slot

The slot accommodates an optional internal

accessory card (model WEBCARDLX, sold

separately). WEBCARDLX provides an Ethernet

network interface for remote monitoring and

control of the UPS system via SNMP, Web, SSH or

telnet. WEBCARDLX enables remote reboots,

shutdowns, load monitoring, condition reporting

and more.

Remove the cover panel from the slot to insert

the accessory card. Refer to the WEBCARDLX

documentation for additional installation

instructions.

3

4

17-04-276 9335AA.indb 9 5/1/2017 1:24:42 PM

10

5.1 Front Panel Switches

“ON/TEST” Button: This button controls 4 separate functions:

UPS System Power ON

To turn on the UPS system, press the “ON/TEST” button for approximately 1

second until the UPS system beeps, then release the button. The “ON

LINE” LED will illuminate.

UPS System Self-Test

To initiate a self-test of the battery during normal on-line operation, press

this button for approximately 1 second until the UPS system beeps, then

release it. The UPS system will transfer to battery power for 10 seconds.

Note: All LEDs illuminate during a self-test.

Alarm Silence

To silence the UPS system’s on battery alarm, press this button and hold it

until the UPS system beeps, then release the button.

UPS System Cold Start

To use the UPS system as a stand-alone power source when AC power is

unavailable (i.e. during a blackout), press this button twice and hold it until

the UPS system beeps, then release the button. The UPS system will then

provide battery power to its outlets.*

* The “ON BATT” indicator light will be illuminated since the UPS system will be

operating from battery power.

“OFF” Button: This button places the UPS into Bypass mode. Press this

button and hold it until the UPS system beeps, then release it. The battery

will continue to charge and the fan will continue to operate. To turn the

UPS system off completely, including the battery charger, unplug the UPS

system’s power cord after pressing the “OFF” switch.

5.2 Advanced Operational Settings

Economy Mode

The UPS system supports economy mode operation to reduce energy consumption and BTU

emissions. In economy mode, the UPS system operates with increased efficiency when the quality

of utility power is satisfactory to pass through to connected equipment without double conversion.

Economy mode saves energy by suspending double conversion when incoming voltage is within

-12%/+10% of the nominal voltage setting. If the nominal voltage setting is 120V, the UPS system

will remain in economy mode while utility line voltage is between approximately 106V and 132V. If

utility line voltage falls outside this range, the UPS system will either switch back to standard

on-line, double conversion mode or it will switch to battery backup mode, depending on the

severity of the voltage deviation.

Economy mode may be enabled (or disabled) through PowerAlert software or the optional

WEBCARDLX internal accessory card. The UPS system's yellow “BYPASS” LED will illuminate

continuously when economy mode is enabled. Refer to the PowerAlert or WEBCARDLX

documentation for more information.

On-line, double-conversion mode (default)

Typical line efficiency at full load: 88%

Output voltage range: ± 2% of nominal setting (100/110/115/120/127V)

Economy mode

Typical line efficiency at full load: 97%

Output voltage range: -12%/+10% of nominal setting (100/110/115/120/127V)

5. Operation

17-04-276 9335AA.indb 10 5/1/2017 1:24:43 PM

11

Frequency Conversion

The UPS system automatically selects 50 Hz or 60 Hz operation based on utility power conditions

at start-up and regulates output power within ± 0.05 Hz of the selected frequency. The UPS system

also has an advanced setting that allows continuous frequency conversion from 50 Hz to 60 Hz or

from 60 Hz to 50 Hz. The advanced frequency conversion setting is accessible through PowerAlert

software or the optional WEBCARDLX internal accessory card. When continuous frequency

conversion is enabled, the maximum output capacity of the UPS system is derated by 30%.

5.3 Power Strategy Selection Options

Tripp Lite SmartOnline UPS systems offer several built-in power strategy options that enable the

UPS to optimize performance to meet user needs for MAXIMUM POWER QUALITY, MAXIMUM

EFFICIENCY, and FREQUENCY REGULATION or FREQUENCY CONVERSION operation. The default

AUTO-ADAPTIVE power strategy combines the benefits of high-efficiency and maximum power

quality. Each power strategy option enables the UPS to automatically shift between specific

operating modes as power and UPS status dictates. Available power strategy options include:

Auto-Adaptive Power Strategy (Default from factory)

Enables the UPS to automatically switch between ONLINE MODE and ECONOMY MODE as dictated

by the quality and reliability of UPS input power. If the UPS does not experience a power failure in a

week’s time (not including UPS self-test) the UPS will automatically switch to ECONOMY MODE. If a

power failure occurs, the UPS will maintain output in BATTERY MODE. When power is restored, the

UPS will repeat the cycle by running in ONLINE MODE until there are no power failures for one

week.

Max Efficiency Power Strategy

Enables the UPS to run continuously in ECONOMY MODE any time incoming AC power is within the

configured bypass low/high voltage range. If UPS input voltage is outside the configured bypass

range, the UPS will automatically switch to ONLINE MODE until AC input voltage is restored within

the configured bypass voltage range. This is similar to Auto-Adaptive Power Strategy, except transfer

to ECONOMY MODE is immediate as voltage levels recover. There is no one-week time period of

power-failure-free operation required in order for the UPS to return to ECONOMY MODE operation.

Max Quality Power Strategy

Enables the UPS to run continuously in ONLINE MODE the entire time incoming AC power is within

the range for online mode operation. The UPS will remain operating continuously in Online Double-

Conversion mode, providing the highest quality output power with zero transfer time. Auto-bypass

mode is available during UPS failure modes when AC input is within the bypass range.

Frequency Regulation Power Strategy

Similar to Max Quality Power Strategy, except the UPS will actively regulate output frequency within

+/-0.05Hz of the 50 or 60Hz nominal frequency measured on startup. The UPS will remain

operating continuously in Online Double-Conversion mode, providing the highest quality output

power with zero transfer time. Auto-bypass mode is available during UPS failure modes when AC

input is within the bypass range.

Frequency Conversion to 60Hz & Frequency Conversion to 50Hz Power Strategies

Similar to Max Quality power strategy, except the UPS will actively regulate output within +/-0.05Hz

of the 50Hz (Freq. Conv. to 50Hz setting) or 60Hz (Freq. Conv. to 60Hz setting). Auto-bypass is not

available in FREQUENCY CONVERSION mode. Typical applications include converting 50 to 60Hz

(or 60 to 50Hz) for sensitive electronic devices.

Note: Maximum power supported in Frequency Regulation/Conversion modes is derated by 30%.

5. Operation

17-04-276 9335AA.indb 11 5/1/2017 1:24:43 PM

12

5.4 Front Panel Indicator Lights

Note: All LEDs illuminate during a UPS system self-test.

“ON LINE” LED: This green LED will illuminate continuously to indicate the

UPS system is operating normally in on-line mode (filtering and

resynthesizing AC line input to provide pure sine wave output). When this

LED is illuminated, the load level of the UPS system is displayed on the %

level LEDs (25%, 50%, 75%, 100%).

“LINE” LED: This green LED will illuminate continuously to indicate the

utility-supplied AC line voltage at the wall outlet is nominal. It will flash if

the line voltage is outside the nominal range (either too low or too high).

User action is not required when the LED flashes; the UPS system

continuously and automatically filters AC line power to provide equipment

with pure sine wave AC power, regardless of brownout or overvoltage

conditions. If this LED is off, then AC line voltage is not present (blackout)

or is at an extremely high voltage, and the UPS system will provide

connected equipment with power from its battery system.

“BYPASS” LED: This yellow LED will illuminate continuously when the UPS

system is in economy mode. The LED will flash when the UPS system is

bypass mode, indicating that the UPS system’s DC/AC inverter is

deactivated. The red “FAULT” LED will also illuminate if the UPS system is in

bypass mode due to a fault. During normal operation, the bypass LED will

illuminate briefly when the unit is plugged in. If an internal fault or overload

occurs, the LED will flash repeatedly to show that connected equipment will

receive filtered AC line power, but will not receive battery power during a

blackout. In this case, contact Tripp Lite for service.

“FAULT” LED: This red LED will flash when the UPS system detects an

internal fault. If the condition persists after restarting the UPS system, see

Section 6: Troubleshooting.

“LOAD” LED: This green LED will illuminate when the UPS system is

receiving AC power. It also illuminates the % level LEDs (25%, 50%, 75%,

100%) indicating the UPS load level.

“BATT” LED: This green LED will illuminate when the UPS system is

operating from battery power. It illuminates the % level LEDs (25%, 50%,

75%, 100%) indicating the battery charge level. (The “ON BATT” LED will

also be illuminated.)

% Level LEDs: These dual-function LEDs will indicate the % level for either

the load level (if the “LOAD” LED is lit) or the battery charge level (if the

“BATT” LED is lit).

“OVERLOAD” LED: This red LED will illuminate continuously to indicate that

the UPS system’s capacity has been exceeded. The UPS alarm will beep

continuously. Immediately unplug some equipment until the LED and alarm

go off. If the overload is not corrected immediately, the UPS system will go

from on-line to bypass mode.

5. Operation

17-04-276 9335AA.indb 12 5/1/2017 1:24:45 PM

13

“BATT LOW” LED: This yellow LED will illuminate when the UPS system’s

battery charge level is low. The UPS alarm will beep until the batteries are

either depleted or adequately recharged.

“ON BATT” LED: This green LED will illuminate continuously to indicate AC

line voltage is absent (or out of range) and the UPS system is providing

equipment with battery-derived AC power. The UPS system will also beep

every 2 seconds (unless silenced by the “ON/TEST” button) and the % level

LEDs (25%, 50%, 75%, 100%) will display the battery charge level.

“REPLACE BATT” LED: This red LED as well as the red “FAULT” LED will

illuminate continuously and the UPS alarm will beep every 2 seconds if the

UPS system fails the automatic self-test. Allow the UPS system to charge

for at least 12 hours and perform a self-test as described in Section 5.1:

Front Panel Switches. If the condition persists, contact Tripp Lite.

5.5 Rear Panel

Accessory Card Slot: Remove the cover panel from this slot to install an

optional internal WEBCARDLX accessory, sold separately. WEBCARDLX

provides a network interface for monitoring and control via SNMP, Web,

SSH or telnet, enabling remote reboots, shutdowns and more.

External Battery Pack Connector

Output Circuit Breakers: These resettable circuit breakers protect the UPS

system from output overload. If a breaker trips, remove some of the load

on the circuit and allow the UPS system to cool before pressing the breaker

button to reset.

Input Power Cord: This permanently attached power cord connects the

UPS system to a compatible power outlet.

NEMA L5-30P

5. Operation

17-04-276 9335AA.indb 13 5/1/2017 1:24:48 PM

14

5.6 Communications

Communication Ports (USB and RS232): These ports connect the UPS

system to a computer. Use with Tripp Lite’s PowerAlert software and

included cabling to allow the computer to automatically save open files and

shut down during a blackout. Also use PowerAlert software to control UPS

system load banks and monitor a wide variety of AC line power and UPS

system operating conditions. See Section 4.4: Optional Connections for

cable connection instructions. Refer to the PowerAlert documentation for

software installation instructions.

The RS232 port may also be used as a contact closure port. The port’s

numbered pin assignments are shown in the RS232 (DB9) illustration at

left. See DB9 Settings in Section 5.8: Configuration Options via

WEBCARDLX for a full list of DB9 features.

EPO (Emergency Power Off) Port: The UPS system has an EPO port that

may be used to connect the UPS system to a contact closure switch to

enable emergency UPS system shutdown. See Section 4.4: Optional

Connections for more information. After re-connecting to utility power, see

Section 4.3: Connection and Start-Up for start-up instructions.

Battery Pack Configuration Port: For external batteries with

communication built-in, plugging the battery communication cable into this

port allows the UPS to automatically detect the external battery. This wired

data connection enables automatic detection and configuration for up to 6

SMART Battery Packs to the UPS.

AC Outlets: These outlets provide connected equipment with pure sine

wave AC output derived from the AC line during normal operation and

derived from battery power during blackouts and severe brownouts or

overvoltages. Output power is filtered to protect connected equipment

against damaging surges and line noise.

The outlets are divided into numbered load banks, as labelled on the unit.

Using PowerAlert software and cabling or an optional WEBCARDLX, load

banks may be individually turned off and on from a remote location,

allowing users to reset or reboot connected equipment.

CONTROLLABLE LOAD 1

CONTROLLABLE LOAD 2

RS232 (DB9)

5. Operation

NEMA L5-30R

NEMA 5-15/20R

USB

17-04-276 9335AA.indb 14 5/1/2017 1:24:51 PM

15

5.7 Configuring External Battery Packs

This UPS system supports the connection of external battery packs to enable extended-run UPS

operation. In order for the UPS to provide efficient charging levels and accurate runtime predictions

for optimal network runtime prior to sending auto-shutdown messaging, external battery packs

need to be configured to the UPS upon installation.

There are 2 methods available to configure external battery packs to the UPS, depending on

battery pack selected and quantity connected to the UPS. Some battery pack configurations may

require the use of more than one configuration method.

METHOD 1: External batteries can be configured to the UPS automatically using SMART Battery

Packs. UPS supports automatic detection of up to 6 SMART BATTERY PACKS connected to the

UPS.

METHOD 2: External batteries can be configured to the UPS using External Battery

Configuration software. The software can be used to configure the UPS for any supported quantity

of SMART & NON-SMART external battery packs.

Tripp Lite SMART Battery Packs include a wired data connection that enables automatic detection

and configuration for up to 6 SMART Battery Packs to the UPS. Tripp Lite Legacy NON-SMART

battery packs are also supported for extended runtime applications, but require user configuration

through the use of EXTERNAL BATTERY CONFIGURATION SOFTWARE.

SmartOnline SMART and NON-SMART External Battery Pack Options

SU3000RTXL2U

Supported “SMART” BATTERY PACKS BP72V18-2US

Supported LEGACY “NON-SMART” BATTERY PACKS BP72V15 (limit 1)

BP72V28RT3U

Configuring SMART and NON-SMART BATTERY PACKS

Adding up to 6 SMART BATTERY PACKS to the UPS

Each SmartOnline UPS has a designated SMART BATTERY PACK, where up to 6 SMART battery

packs may be connected to the UPS for fully automatic detection and configuration. SMART battery

packs include a wired data connection that connects to the UPS Battery Pack Detection port for

automatic recognition and configuration by the UPS.

To configure the UPS for use with up to 6 SMART BATTERY PACKS, connect the included POWER

and DATA cables between the UPS and the first SMART BATTERY PACK. Then connect the POWER

and DATA cables for additional SMART BATTERY PACKS to the one ahead of it. The UPS will

automatically detect and configure up to 6 SMART BATTERY PACKS to the UPS.

Adding more than 6 SMART or NON SMART BATTERY PACKS to the UPS

When configuring the UPS with more than 6 SMART or NON SMART BATTERY PACKS, configure all

SMART and NON SMART BATTERY PACKS using Tripp Lite's External Battery Configuration Software.

This includes all SMART BATTERY PACKS configured previously.

Note: Refer to https://www.tripplite.com/support/external-battery-configuration-utility for program download and

instructions.

5. Operation

17-04-276 9335AA.indb 15 5/1/2017 1:24:51 PM

16

5.8 Configuration Options via WEBCARDLX

CONTROL DEVICE

Setting Value(s) Description

Auto Batt. Testing

(Set regular battery

self-test interval)

• Disable

• 4 weeks (factory setting)

• 13 weeks

• 26 weeks

Use this option to initiate automatic

UPS battery testing at regular

intervals.

Reset to Factory

Settings

• Factory Reset Use this option to reset all UPS

preferences to factory settings,

including battery conﬁgurations.

CONFIGURATION DEVICE SETTINGS DEVICE PROPERTIES

Property Value(s) Description

Audible alarm • Enable

• Disable

Audible Alarm DISABLE setting

prevents power fail and operating

fault alarms only; the UPS will

always “beep” to conﬁrm the UPS is

accepting user input.

Output Voltage • 100

• 110

• 115

• 120

• 127

Use this option to set the nominal

UPS output voltage (changes take

effect on next restart).

Power Strategy • Auto-Adaptive (factory setting)

• Max Efﬁciency

• Max Quality

• Freq. Regulation

• Freq. Conversion to 60Hz

• Freq. Conversion to 50Hz

Use this option to set the UPS Power

strategy.

See Section 5.3: Power Strategy

Selection Options under

Operations for more info on available

power strategy options.

Cold Start • Enable (factory setting)

• Disable

Enabling Cold Start allows the UPS

to be manually turned on into battery

mode during a power failure.

Auto-Restart • Enable (factory setting)

• Disable

Enabling Auto-Restart allows the UPS

to automatically turn back on into

a protected operating mode when

power is restored.

Auto-Restart Delay Enter: 0 to 60 seconds

(factory setting is 0 seconds)

Auto-Restart delay forces the UPS

to wait 0-60 seconds after power

is restored before automatically

restarting. Requires Auto-Restart be

enabled when power is restored.

Energy Saving • Enter: 0-100%

• Disable (factory setting)

Energy Saving enables the UPS to

automatically shutdown when the

output load is less than the selected

percentage continuously for 5

minutes.

Off Mode • Standby

• Bypass (factory setting)

Off Mode setting of BYPASS allows

the UPS to provide unregulated line

power within conﬁgured bypass

low / high limits to be available at the

output of the UPS when it is turned

off.

5. Operation

17-04-276 9335AA.indb 16 5/1/2017 1:24:51 PM

17

CONFIGURATION DEVICE SETTINGS DEVICE PROPERTIES

Property Value(s) Description

Min. Batt. to

Restart

• Enter: 10-90%

• Disable (factory setting)

Minimum battery charge level

to restart forces the UPS to wait

until batteries have recharged to

the selected percentage before

automatically restarting.

Note: UPS can be manually started using

the power button if battery is below the

minimum battery restart threshold.

Requires Auto-Restart be enabled

when power is restored.

Low Batt. Alert • Enter: 10-90%

(factory setting is 20%)

Enables the UPS to send a low-

battery alert as batteries discharge

to the selected charge level during a

power failure.

Timed Shutdown • Enter a time interval (mm:ss) Timed Shutdown sets the maximum

amount of battery runtime in seconds

or minutes the UPS will provide during

a power failure.

Timed Shutdown • Enable/Disable (factory setting) Use the DISABLE setting for the

longest possible battery runtime.

Shutdown

Completion

• Required (factory setting)

• Interrupt OK

The UPS will communicate shutdown

messaging to connected systems

prior to UPS shutdown. The setting of

INTERRUPT OK will interrupt shutdown

messaging if power is restored after

shutdown messaging is sent.

DB9 Settings

(Output pins 1&5)

• On battery (factory setting)

• On bypass

• Output on

• Low battery

The UPS will signal the selected

condition by shorting pins 1&5 on the

DB9 port.

DB9 Settings

(Output pins 8&5)

• On battery

• On bypass

• Output on

• Low battery (factory setting)

The UPS will signal the selected

condition by shorting pins 8&5 on the

DB9 port.

5. Operation

17-04-276 9335AA.indb 17 5/1/2017 1:24:51 PM

18

CONFIGURATION DEVICE SETTINGS DEVICE PROPERTIES

Property Value(s) Description

DB9 Settings

(Input pins 3&9)

• Shutdown (factory setting)

• Output off

• Reboot

• Output on

• Power Toggle

The UPS will perform the selected

action when pins 3&9 are shorted on

the DB9 port for at least 3.8 seconds.

For the Reboot option (output off for

30 seconds before reboot):

The pins must be shorted for at least

3.8 seconds to perform the reboot.

The reboot happens at exactly 3.8

seconds. If the pins continue to be

shorted for more than 3.8 seconds,

no further action should be taken.

The UPS takes no action on release

of the short.

The Power Toggle option is intended

to keep the unit powered on

whenever the pins are not shorted

and powered off whenever the pins

are shorted. This input cannot power

on the unit from an off state unless

valid AC is applied (this function will

not impose a cold start). To power

on, the pins must be not shorted for

at least 3.8 seconds and AC must be

valid. To power off, the pins must be

shorted for at least 3.8 seconds.

CONFIGURATION DEVICE SETTINGS DEVICE THRESHOLDS

Property Value(s) Description

Overload Alert Lvl. • Enter: 5-105%

(factory setting is 100%)

Sets the UPS output load percentage

before an overload alert is sent.

Conf. Fault Action

(UPS response to

fault)

• Go to bypass (factory setting)

• Go to standby

Sets the UPS response to fault

conditions that require the UPS to

exit double-conversion mode. GO

TO BYPASS option maintains AC

output (so long as input voltage is

within bypass high/low limits). GO TO

STANDBY option causes the UPS to

turn off output AC in response to fault

conditions.

Bypass Low Limit • Enter: -5% to -20%

(factory setting is -15%)

Speciﬁes the lowest acceptable input

voltage for bypass operation.

Bypass High Limit • Enter: +5% to +20%

(factory setting is +10%)

Speciﬁes the highest acceptable input

voltage for bypass operation.

5. Operation

17-04-276 9335AA.indb 18 5/1/2017 1:24:51 PM

19

The UPS system control panel LEDs will illuminate in the sequences listed below to indicate

operational problems.

Note: If the “FAULT” LED illuminates, determine the specific fault condition by activating the error code LEDs. To

activate the error code LEDs, press the “ON/TEST” button until the UPS system beeps, then release the button.

The error code LEDs will illuminate for 5 seconds.

Illuminated LEDs Condition and Solution

On: REPLACE BATT

Error Code LEDs: Not Applicable

Replace Battery: Allow the UPS system to charge for at least

12 hours and perform a UPS system self-test as described in

Section 5.1: Front Panel Switches. If the LED remains on,

contact Tripp Lite for service.

Flashing: LINE

Error Code LEDs: Not Applicable

Input Abnormal: Utility power voltage or frequency is too high

or too low for the UPS system to operate in BYPASS mode. If

an inverter failure occurs, the UPS system will not pass through

utility power to the outlets and any connected equipment will

turn off.

On: FAULT

Error Code LEDs: 50% 100%

Battery Weak: Allow the UPS system to charge for 12 hours. If

the LED remains on, contact Tripp Lite for service.

On: FAULT

Error Code LEDs: 25% 50%

Inverter Over-Current: Reduce the load supported by the UPS

system by unplugging some equipment. Restart the UPS system.

If the problem persists, contact Tripp Lite for service.

On: FAULT

Error Code LEDs: 25% 75% 100%

Internal Temperature Too High: Conﬁrm that adequate space

exists for air to circulate near the UPS system’s vents. Conﬁrm

that the UPS system’s fan is working properly. Conﬁrm that the

ambient temperature does not exceed recommended levels.

Restart the UPS system.

On: FAULT

Error Code LEDs: 25% 75%

Inverter Overload: Reduce the load supported by the UPS

system by unplugging some equipment.

On: FAULT

Error Code LEDs: 25% 50% 100%

Charger Out of Order: Restart the UPS system. If the problem

persists, contact Tripp Lite for service.

On: FAULT

Error Code LEDs: 25% 50% 75%

Fan Out of Order: Restart the UPS system. If the problem

persists, contact Tripp Lite for service.

On: FAULT

Error Code LEDs: 25% 50% 75% 100%

Bypass Phase Can’t Lock: Restart the UPS system. If the

problem persists, contact Tripp Lite for service.

On: FAULT

Error Code LEDs: BATT 75% 100%

Wiring Fault: Check the utility line for wiring problems such as

reversed line and neutral or a missing ground. The UPS system

will detect some (but not all) wiring faults. Contact an electrician

to verify the AC input wiring.

On: FAULT

Error Code LEDs: BATT 25%

Utility Voltage Low and Battery Disconnected at

Initialization: Shut down the UPS system. Check the internal

battery connections. Correct the AC input voltage. Restart the

UPS system. If the problem persists, contact Tripp Lite for service.

On: FAULT

Error Code LEDs: BATT 25% 100%

Utility Voltage Low and Battery Disconnected in On-Line

Mode: Shut down the UPS system. Check the internal battery

connections. Correct the AC input voltage. Restart the UPS

system. If the problem persists, contact Tripp Lite for service.

On: FAULT

Error Code LEDs: BATT 25% 75%

Input Over-Current: Reduce the load supported by the UPS

system by unplugging some equipment. Restart the UPS system.

If the problem persists, contact Tripp Lite for service.

On: FAULT

Error Code LEDs: BATT 25% 50%

Bypass Overload: Reduce the load supported by the UPS

system by unplugging some equipment. Either wait for the UPS

system to recognize the load reduction or restart the UPS system.

If the problem persists, contact Tripp Lite for service.

On: FAULT

Error Code LEDs: BATT 25% 50% 100%

Battery Voltage Too High: Restart the UPS system. If the

problem persists, contact Tripp Lite for service.

Note: All other error codes may indicate internal fault conditions. Restart the UPS system. If the problem

persists, contact Tripp Lite for service.

6. Troubleshooting

17-04-276 9335AA.indb 19 5/1/2017 1:24:51 PM

20

7. Battery Replacement

Under normal conditions, the original batteries in the UPS system will last several years. The

batteries are designed for hot-swap replacement (i.e. replacement while the UPS system is in ON

mode). Batteries may also be replaced when the UPS is switched off and supported equipment is

disconnected.

Battery Warnings

Batteries can present a risk of electrical shock and burn from high short-circuit current.

Observe the following precautions:

CAUTION: Do not dispose of batteries in a ﬁre. The batteries may explode.

CAUTION: Do not open or mutilate batteries. Released electrolyte is harmful to the skin and eyes. It

may be toxic.

CAUTION: A battery can present a risk of electrical shock and high short-circuit current. The

following precautions should be observed when working on batteries:

a) Remove watches, rings, or other metal objects.

b) Use tools with insulated handles.

c) Wear rubber gloves and boots.

d) Do not lay tools or metal parts on top of batteries.

e) Disconnect charging source prior to connecting or disconnecting battery terminals.

f) Determine if battery is inadvertently grounded. If inadvertently grounded, remove source from

ground. Contact with any part of a grounded battery can result in electrical shock. The likelihood

of such shock can be reduced if such grounds are removed during installation and maintenance

(applicable to equipment and remote battery supplies not having a grounded supply circuit).

Unplug and turn off the UPS before performing battery replacement. There are no user-serviceable

parts inside the UPS. Battery replacement should be performed only by authorized service personnel

using the same number and type of batteries (Sealed Lead-Acid). The batteries are recyclable. Refer

to local codes for disposal requirements or visit http://www.tripplite.com/support/recycling-program

for recycling information. Tripp Lite offers a complete line of UPS System Replacement Battery

Cartridges (R.B.C.).Visit Tripp Lite on the Web at http://www.tripplite.com/products/battery-ﬁnder/ to

locate the speciﬁc replacement battery for your UPS.

UPS and Battery Recycling

Please recycle Tripp Lite Products. The batteries used in Tripp Lite products are sealed

Lead-Acid batteries. These batteries are highly recyclable. Please refer to local codes

for disposal requirements.

Call Tripp Lite for recycling info at 1.773.869.1234.

Go to the Tripp Lite Website for up-to-date information on recycling the batteries or any

Tripp Lite product. Please follow this link:

http://www.tripplite.com/support/recycling-program/

17-04-276 9335AA.indb 20 5/1/2017 1:24:51 PM

La page charge ...

Tripp Lite SU3000RTXL2U Le manuel du propriétaire

Tripp Lite SU3000RTXL2U Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents