Simplicity 6271200X43 Manuel utilisateur

Catégorie
Souffleuses à neige
Taper
Manuel utilisateur

Ce manuel convient également à

1741062 TP 199-4725-00-ST-Y
Read and keep this book for future reference. This book contains important information on SAFETY,
ASSEMBLY, OPERATION, AND MAINTENANCE.
Lisez et conservez ce manuel pour référence. Ce manuel contient des informations importantes
concernant la
SECURITE, LE MONTAGE, L’UTILISATION ET L’ENTRETIEN.
Instruction Book Snow Thrower Model 6271200X43
Manuel d’instructions chasse−neige modèle 6271200X43
2
1741062
NOTE: This unit is equipped with an internal combustion engine
and must not be used on or near any unimproved
forestcovered, brushcovered or grasscovered land unless
the engine’s exhaust system is equipped with a spark arrester
meeting applicable local or state laws (if any). If a spark arrester
is used, it must be maintained in effective working order by the
operator.
In the State of California, the above is required by law (Section
4442 of the California Public Resources Code). Other states
may have similar laws. Federal laws apply on federal lands. See
an Authorized Service Center for a spark arrester for the
muffler.
Engine Exhaust, some of its constituents, and
certain vehicle components contain or emit
chemicals known to the State of California to
cause cancer and birth defects or other repro-
ductive harm.
Battery posts, terminals and related accesso-
ries contain lead and lead compounds, chemi-
cals known to the State of California to cause
cancer and birth defects or other reproductive
harm. WASH HANDS AFTER HANDLING.
REMARQUE : cette machine est équipée d’un moteur à
combustion interne et ne doit pas être utilisée sur un terrain
forestier, buissonnant ou herbeux non préparé, à moins que le
dispositif d’échappement soit pourvu d’un pareétincelles
conforme à la législation locale ou de l’état (le cas échéant). Si
un pareétincelles est utilisé, celuici doit être maintenu en
parfait état de fonctionnement par l’utilisateur.
Au sein de l’état de Californie, la loi exige la prise en compte
des précautions mentionnées cidessus (clause 4442 du
California Public Resources Code). D’autres états peuvent
présenter des lois similaires. Les lois fédérales s’appliquent sur
les terres fédérales. S’adresser à un centre de maintenance
agréé pour l’achat d’un pareétincelles pour l’échappement.
Les gaz d’échappement du moteur, certains
éléments de leur composition, ainsi que
certains organes du véhicule contiennent ou
émettent des substances chimiques qui, selon
l’État de Californie, peuvent causer le cancer,
des malformations à la naissance, ou
représentent un danger pour la reproduction.
Les bornes et pôles de batterie et autres
accessoires de ce type contiennent du plomb et
des composés de plomb, substances
chimiques qui, selon l’État de Californie,
peuvent causer le cancer, des malformations à
la naissance, ou représentent un danger pour la
reproduction.
RULES FOR SAFE OPERATION
3
1741062
General Information
This instruction book is written for a person with some mechanical ability.
Like most service books, not all the steps are described. Steps on how to
loosen or tighten fasteners are steps anyone can follow with some
mechanical ability. Read and follow these instructions before you use the
unit.
Know your product: If you understand the unit and how the unit
operates, you will get the best performance. As you read this manual,
compare the illustrations to the unit. Learn the location and the function of
the controls. To help prevent an accident, follow the operating instructions
and the safety rules. Keep this manual for future reference.
IMPORTANT: Many units are not assembled and are sold in cartons. It is
the responsibility of the owner to make sure the assembly instructions in
this manual are exactly followed. Other units are purchased in an
assembled condition. On assembled units, it is the responsibility of the
owner to make sure the unit is correctly assembled. The owner must
carefully check the unit according to the instructions in this manual before
it is first used.
This manual contains safety information to make you
aware of the hazards and risks associated with snow
throwers, and how to avoid them. The snow thrower is designed and
intended for removal of snow, and should not be used for any other
purpose. It is important that you read and understand these
instructions, and anyone operating the equipment read and
understand these instructions.
The engine exhaust from this product contains chemicals known to the
State of California to cause cancer, birth defects, or other reproductive
harm.
WARNING
A signal word (DANGER, WARNING, or CAUTION) is used with the alert
symbol to indicate the likelihood and the potential severity of injury. In
addition, a hazard symbol may be used to represent the type of hazard.
DANGER indicates a hazard which, if not avoided, will result in
death or serious injury.
WARNING indicates a hazard which, if not avoided, could result
in death or serious injury.
CAUTION indicates a hazard which, if not avoided, might result
in minor or moderate injury.
CAUTION, when used without the alert symbol, indicates a
situation that could result in damage to the equipment.
Hazard Symbols and the meanings
These symbols are used on your equipment and defined in your operating
manual. Review and understand the meanings. The use of one of these
symbols combined with a signal word will alert you to potential hazards
and how to avoid them.
Explosion
Toxic fumes
Shock
Hot Surface
Fire
Operator’s Manual Read and understand
before performing any activity or running
equipment.
Safety Alert Identifies safety information about
hazards that can result in personal injury.
Rotating auger
Rotating impeller
Rotating gears
Thrown objects
Keep a safe distance
from the equipment.
Shut off engine and
remove spark plug
connector before
performing maintenance
or repair work.
Never reach into
rotating parts.
Recommended ear
protection for
extended use.
RULES FOR SAFE OPERATION
4
1741062
Operating Symbols and their meanings
These symbols are used on your equipment and defined in your operating
manual. It is important that you review and understand the meanings.
Failure to understand the symbols might result in harm to you.
Stop
Fuel
Choke off
Oil
Choke on
Slow
Fast
On Off
Ignition Key
Ignition Off
Ignition On
Primer bulb
Throttle
Drive Clutch
Auger Clutch
Engage
RIGHT
Auger Collector
Traction
Discharge Chute
LEFT UP
DOWN
Forward
Neutral
Reverse
Push to engage
electric start
Electric
Start
Engine
Start
Engine Run
Engine Off
Chute Deflector
Engage
Disengage
Heated Grips
Avoid death or serious injury from rotating auger.
Keep hands, feet and clothing away.
Unclogging discharge chute is a hazardous activity.
Stop engine and disconnect spark plug wire when performing maintenance
on equipment.
Never leave the equipment unattended while engine is running. Always
disengage the auger and traction controls, stop engine, and remove keys.
Keep children, pets, and others out of the area during operation. Children
are often attracted to the equipment. Be mindful of all persons present.
Keep all loose clothing far away from front of snow thrower and auger.
Scarves, mittens, dangling drawstrings, loose clothes and pants can
quickly become caught in the rotating device and dismemberment will
occur. Tie up long hair and remove jewelry.
The snow thrower is intended to remove snow only. Do not use for
purposes other than what is intended.
Do not clear snow across the face of slopes. Exercise extreme caution when
changing direction on slopes. Do not attempt to clear steep slopes.
Do not use the snow thrower on surfaces above ground level such as roofs
of residences, garages, porches or other such structures or buildings.
DANGER
Discharge chute contains rotating impeller to throw snow.
Never clear or unclog discharge chute with your hands, or
while engine is running.
Fingers can quickly become caught and traumatic
amputation or severe laceration can result.
Unclogging the discharge chute is a hazardous activity. Clogged or
blocked augers store energy and can rotate unexpectedly.
Never place hands in or near discharge chute.
With engine OFF, wait for all moving parts to cease movement, then with a
stick, clear the chute. Even with engine off, parts may rotate and
dismemberment can occur.
Clogged snow can hide other obstructions in the chute and cause damage
to the equipment, impeller or auger. Take precautions when restating the
equipment after snow removal.
DANGER
RULES FOR SAFE OPERATION
5
1741062
Objects can be picked up by auger and thrown from chute.
Never throw snow toward people or cars, and never allow
anyone in front of the snow thrower.
Be aware of your environment while operating equipment. Running over
items such as, gravel, doormats, newspapers, toys, and rocks hidden
under snow, can all be thrown from chute or jam in the auger.
Always be aware of the direction the snow is being thrown. Nearby
pedestrians, pets or property may be harmed by objects being thrown.
Familiarize yourself with the area you plan to work. Mark off boundaries of
walkways and driveways to prevent property damage from thrown objects.
Take caution when snow throwing in unfamiliar areas. Stay alert for hidden
hazards and traffic.
After striking a foreign object, turn engine OFF, wait for moving parts to
cease movement, and check immediately for damage. If damaged, repair
before starting and operating snow thrower.
With engine OFF, wait for moving parts to stop and always use a stick to
clear discharge chute.
If unit vibrates abnormally, turn engine OFF. Vibration is generally a
warning of trouble. See an authorized dealer if necessary for repairs.
DANGER
Rotating gears can contact or entangle hands, feet, hair,
clothing, or accessories.
Traumatic amputation or severe laceration can result.
Always operate equipment with all guards in place.
Keep hands and feet away from rotating gears.
Tie up long hair and remove jewelry.
Do not wear loose-fitting clothing, dangling drawstrings or items that could
become caught.
WARNING
Engines give off carbon monoxide, an odorless, colorless,
poison gas.
Breathing carbon monoxide can cause nausea, fainting or
death.
Start and run engine outdoors.
Do not start or run engine in enclosed area, even if doors or
windows are open.
WARNING
Allow muffler, engine cylinder and fins to cool before touching.
Remove accumulated combustibles from muffler area and cylinder
area.
Install and maintain in working order a spark arrester before using
equipment on forest-covered, grass-covered, brush-covered
unimproved land. The state of California requires this (Section 4442 of
the California Public Resources Code). Other states may have similar
laws. Federal laws apply on federal land.
WARNING
Running engines produce heat. Engine parts, especially muffler,
become extremely hot.
Severe thermal burns can occur on contact.
Combustible debris, such as leaves, grass, brush, etc. can catch
fire.
Gasoline and its vapors are extremely flammable and explosive.
Fire or explosion can cause severe burns or death.
WHEN ADDING FUEL
Turn engine OFF and let engine cool at least 2 minutes before removing
gas cap.
Fill fuel tank outdoors or in well-ventilated area.
Do not overfill fuel tank.
Keep gasoline away from sparks, open flames, pilot lights, heat, and other
ignition sources.
Check fuel lines, tank, cap, and fittings frequently for cracks or leaks.
Replace if necessary.
WHEN STARTING ENGINE
Make sure spark plug, muffler, fuel cap and air cleaner are in place.
Do not crank engine with spark plug removed.
If fuel spills, wait until it evaporates before starting engine.
If engine floods, set choke to OPEN/RUN position, place throttle in FAST
and crank until engine starts.
WHEN OPERATING EQUIPMENT
Do not choke carburetor to stop engine.
WHEN TRANSPORTING EQUIPMENT
Transport with fuel tank EMPTY.
WHEN STORING GASOLINE OR EQUIPMENT WITH FUEL IN TANK
Store away from furnaces, stoves, water heaters or other appliances that
have pilot light or other ignition source because they can ignite gasoline
vapors.
WARNING
Starting engine creates sparking.
Sparking can ignite nearby flammable gases.
Explosion and fire could result.
If there is natural or LP gas leakage in area, do not start engine.
Do not use pressurized starting fluids because vapors are flammable.
WARNING
Unintentional sparking can result in fire or electric shock.
Unintentional start-up can result in entanglement, traumatic
amputation, or laceration.
BEFORE PERFORMING ADJUSTMENTS OR REPAIRS
Disconnect spark plug wire and keep it away from spark plug.
WHEN TESTING FOR SPARK
Use approved spark plug tester.
Do not check for spark with spark plug removed.
WARNING
IMPORTANT: Safety standards require operator presence control to
minimize the risk of injury. Your snowthrower is equipped with such
controls. Do not attempt to defeat the function of the operator presence
control under any circumstances.
Training
1. Read, understand, and follow all instructions on the machine and in
the manuals before operating this unit. Be thoroughly familiar with
the controls and the proper use of the equipment. Know how to stop
the unit and disengage the controls quickly.
2. Never allow children to operate the equipment. Never allow adults to
operate the equipment without proper instruction.
3. Keep the area of operation clear of all persons, particularly small
children, and pets.
4. Exercise caution to avoid slipping or falling especially when operating
in reverse.
Preparation
1. Thoroughly inspect the area where the equipment is to be used and
remove all doormats, sleds, boards, wires, and other foreign objects.
2. Disengage all clutches and shift into neutral before starting the
engine (motor).
3. Do not operate the equipment without wearing adequate winter outer
garments. Wear footwear that will improve footing on slippery
surfaces. Avoid loose fitting clothing that can get caught in moving
parts.
4. Handle fuel with care; it is highly flammable.
a. Use an approved fuel container.
b. Never add fuel to a running engine or hot engine.
c. Fill fuel tank outdoors with extreme care. Never fill fuel tank
indoors. Replace fuel cap securely
and wipe up spilled fuel.
d. Never fill containers inside a vehicle or on a truck or trailer bed
with a plastic liner. Always place containers on the ground, away
from your vehicle, before filling.
ro kcurt eht morf tnempiuqe derewop- sag evomer ,lacitcarp nehW.e
trailer and refuel it on the ground. If this is not possible, then refuel
such on a trailer with a portable container, rather than from a
gasoline dispenser nozzle.
f. Keep nozzle in contact with the rim of the fuel tank or container
opening at all times, until refueling is complete. Do not use a
nozzle lock-open device.
g. Replace gasoline cap securely and wipe up spilled fuel.
h. If fuel is spilled on clothing, change clothing immediately.
5. Use extension cords and receptacles as specified by the
manufacturer for all units with electric drive motors or electric
starting motors.
6. Adjust the
collector housing height to clear gravel or crushed rock
surfaces.
7. Never attempt to make any adjustments while the engine (motor) is
running (except when specifically recommended by manufacturer).
8.
Let engine (motor) and snowthrower adjust to outdoor temperatures
before starting to clear snow.
9. Always wear safety glasses or eye shields during operation or while
performing an adjustment or repair to protect eyes from foreign
objects that may be thrown from the machine.
Operation
1. Do not put hands or feet near or under rotating parts. Keep clear of
the discharge opening at all times.
2. Exercise extreme caution when operating on or crossing gravel
drives, walks or roads. Stay alert for hidden hazards or traffic.
3. After striking a foreign object, stop the engine (motor), remove the
wire from the spark plug, disconnect the cord on electric motors,
thoroughly inspect snowthrower for any damage, and repair the
damage before restarting and operating the snowthrower.
4. If the unit should start to vibrate abnormally, stop the engine (motor)
and check immediately for the cause. Vibration is generally a warning
of trouble.
5. Stop the engine (motor) whenever you leave the operating position,
before unclogging the collector/impeller housing or discharge chute
and when making any repairs, adjustments, or inspections.
6. When cleaning, repairing, or inspecting, make certain the collector/
impeller and all moving parts have stopped. Disconnect the spark
plug wire and keep the wire
away from the spark plug to prevent
accidental starting.
7. Do not run the engine indoors, except when starting the engine and
for transporting the snowthrower in or out of the building. Open the
outside doors; exhaust fumes are dangerous (containing CARBON
MONOXIDE, an ODORLESS and DEADLY GAS).
8. Exercise extreme caution when operating on slopes. Do not attempt
to clear steep slopes.
9. Never operate the snowthrower without proper guards, plates, or
other safety protective devices in place and working.
10. Never direct the discharge toward people or areas where property
damage can occur. Keep children and others away.
11. Do not overload the machine capacity by attempting to clear snow at
too fast a rate.
12. Never operate the machine at high transport speeds on slippery
surfaces. Look behind and use care when operating in reverse.
13. Disengage power to the collector/impeller when snowthrower is
transported or not in use.
14. Use only attachments and accessories approved by the manufacturer
of the snowthrower (such as cabs, tire chains, etc.).
15. Never operate the snowthrower
without good visibility or light.
Always be sure of your footing and keep a firm hold on the handles.
Walk, never run.
16. Never touch a hot engine or
muffler.
RULES FOR SAFE OPERATION
6
WARNING: This machine is capable of amputating hands and feet and throwing objects. Read these safety rules and follow them closely.
Failure to obey these rules could result in loss of control of unit, severe personal injury or death to you, or bystanders, or damage to property
or equipment. The triangle in text signifies important cautions or warnings which must be followed.
Safe Operation Practices for Snowthrowers
As Recommended By: American National Standards Institute (ANSI)
1741062
17. Never operate the snowthrower near glass enclosures, automobiles,
window wells, drop-offs, and the like without proper adjustment of
the snow discharge angle.
18. Never direct discharge at bystanders or allow anyone in front of the
unit.
19. Never leave a running unit unattended. Always disengage the auger
and traction controls, stop engine, and remove keys.
20. Do not operate the unit while under the influence of alcohol or drugs.
21. Keep in mind the operator is responsible for accidents occurring to
other people or property.
22. Data indicates that operators, age 60 years and above, are involved
in a large percentage of power equipment-related injuries. These
operators should evaluate their ability to operate the unit safely
enough to protect themselves and others from injury.
23. DO NOT wear long scarves or loose clothing that could become
entangled in moving parts.
24. Snow can hide obstacles. Make sure to remove all obstacles from the
area to be cleared.
Children
Tragic accidents can occur if the operator is not alert to the presence of
children. Children are often attracted to the unit and the operating activity.
Never assume that children will remain where you last saw them.
1. Keep children out of the area and under
the watchful care of another
responsible adult.
2. Be alert and turn off if children enter the area.
3. Never allow children to operate the unit.
4. Use extra care when approaching blind corners,
shrubs, trees, or
other objects that may obscure vision.
Clearing A Clogged Discharge Chute
Hand contact with the rotating impeller inside the discharge chute is the
most common cause of injury associated with snowthrowers. Never use
your hand to clean out the discharge chute.
To clear the chute:
1. SHUT OFF THE ENGINE.
2. Wait 10 seconds to be sure the impeller blades have stopped
rotating.
3. Always use a clean-out tool, not your hands.
Service, Maintenance And Storage
1. Check shear bolts and other bolts at frequent intervals for proper
tightness to be sure the equipment is in safe working condition.
2. Never store the machine with fuel in the tank inside a building where
ignition sources are present such as hot water and space heaters, or
clothes dryers. Allow the engine to cool before storing in any
enclosure.
3. Always refer to operator’s manual for important details if the
snowthrower is to be stored for an extended period.
4. Maintain or replace safety and instruction labels as necessary.
5. Run
the machine a few minutes after throwing snow to prevent
freeze-up
of
the
collector/impeller
.
6.
If
fuel
is
spilled,
do
not
attempt
to
start
the
engine
but
move
the
machine
away
from
the
area
of
spillage
and
avoid creating any source
of ignition until fuel vapors have dissipated.
7. Always observe safe refueling and fuel handling practices when
refueling the unit after transportation or storage.
8. Always follow the engine manual instructions for storage
preparations before storing the unit for both short and long term
periods.
9. Always follow the engine manual instructions for proper start-up
procedures when returning the unit to service.
10. Maintain or replace safety and instruction labels as necessary.
11. Keep nuts and bolts tight and keep equipment in good condition.
12. Never tamper with safety devices. Check their proper operation
regularly and make necessary repairs if they are not functioning
properly.
13. Components are subject to wear, damage, and deterioration.
Frequently check components and replace with manufacturers
recommended parts, when necessary.
14. Check control operation frequently. Adjust and service as required.
15. Use only factory authorized replacement parts when making repairs.
16. Always comply with factory specifications on
all settings and
adjustments.
17. Only authorized service locations should be utilized for major service
and repair requirements.
18. Never attempt to make major repairs on this unit unless
you have
been properly trained. Improper service procedures can result in
hazardous operation, equipment damage and voiding of
manufacturer’s warranty.
19. Check shear bolts (pins) and other bolts at frequent intervals for
proper tightness to be sure the equipment is in safe working
condition.
Emissions
1. Engine exhaust from this product contains chemicals known, in
certain quantities, to cause cancer, birth defects, or reproductive
harm.
2. If available, look for the relevant Emissions Durability Period and Air
Index information on the engine emissions label.
Ignition System
1. This spark ignition system complies with Canadian ICES-002.
RULES FOR SAFE OPERATION
7
1741062
TABLE OF CONTENTS
8
1741062
HAZARD SYMBOLS AND THE MEANINGS 2. . . . . . . . . .
OPERATING SYMBOLS AND THEIR MEANINGS 3. . . . .
OWNER’S INFORMATION 5. . . . . . . . . . . . . . . . . . . . . . . . . .
ASSEMBLY 9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TOOLS REQUIRED FOR ASSEMBLY 9. . . . . . . . . . . . . .
CONTENTS OF SHIPPING CARTON 9. . . . . . . . . . . . . .
PARTS BAGS CONTENTS: 9. . . . . . . . . . . . . . . . . . . . . . .
UNPACKING 10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..
UPPER HANDLE ASSEMBLY 11. . . . . . . . . . . . . . . . . . . .
CHECK THE CABLES 11. . . . . . . . . . . . . . . . . . . . . . . . . . .
HOW TO SET THE LENGTH OF THE CABLE 11. . . . .
REMOTE CHUTE CONTROL KNOB 12. . . . . . . . . . . . . .
SPEED SELECT KNOB 12. . . . . . . . . . . . . . . . . . . . . . . . .
SNOW CHUTE ASSEMBLY 13. . . . . . . . . . . . . . . . . . . . . .
HOW TO ASSEMBLE THE DRIFT CUTTER 14. . . . . . .
OPERATION 15. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
OPERATING CONTROLS 15. . . . . . . . . . . . . . . . . . . . . . .
SNOW BLOWER OPERATION 16. . . . . . . . . . . . . . . . . . .
BEFORE STARTING ENGINE 17. . . . . . . . . . . . . . . . . . . .
CHECK THE OIL 17. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FILL GAS 17. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TO STOP ENGINE 18. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TO START ENGINE 18. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
HOW TO CLEAR A CLOGGED DISCHARGE CHUTE 20.
HOW TO USE THE CLEAN-OUT TOOL 20. . . . . . . . . . .
OPERATING TIPS 21. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SERVICE RECOMMENDATIONS 22. . . . . . . . . . . . . . . . . . .
CUSTOMER RESPONSIBILITIES 23. . . . . . . . . . . . . . . . . .
SNOW BLOWER 23. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
LUBRICATION AT STORAGE 23. . . . . . . . . . . . . . . . . . . .
LUBRICATION − EVERY 10 HOURS 23. . . . . . . . . . . . . .
LUBRICATION − EVERY 25 HOURS 24. . . . . . . . . . . . . .
ENGINE 25. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ADJUSTMENT/REPAIR 26. . . . . . . . . . . . . . . . . . . . . . . . . . .
AUGER HOUSING HEIGHT ADJUSTMENT 26. . . . . . .
TO ADJUST SCRAPER BAR 26. . . . . . . . . . . . . . . . . . . . .
TO ADJUST SKID HEIGHT 26. . . . . . . . . . . . . . . . . . . . . .
HOW TO REMOVE THE SNOW HOOD 27. . . . . . . . . . .
BELT ADJUSTMENT 28. . . . . . . . . . . . . . . . . . . . . . . . . . . .
HOW TO REPLACE THE BELTS 29. . . . . . . . . . . . . . . . .
BELT GUIDE ADJUSTMENT 32. . . . . . . . . . . . . . . . . . . . .
HOW TO CHECK AND ADJUST THE CABLES 32. . . .
AUGER DRIVE CABLE ADJUSTMENT 32. . . . . . . . . . . .
TRACTION DRIVE CABLE ADJUSTMENT 33. . . . . . . . .
HOW TO ADJUST OR REPLACE
THE FRICTION WHEEL 34. . . . . . . . . . . . . . . . . . . . . . .
AUGER SHEAR BOLT REPLACEMENT 37. . . . . . . . . . .
STORAGE 38. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TROUBLE SHOOTING CHART 39.
. . . . . . . . . . . . . . . . . . . .
ASSEMBLY
9
1741062
TOOLS REQUIRED FOR ASSEMBLY
1 − Knife
2 − 1/2” wrenches (or adjustable wrenches)
2 − 9/16” wrenches (or adjustable wrenches)
2 − 3/4” wrenches (or adjustable wrenches)
1 − 3/8” wrenches (or adjustable wrenches)
1 − Pair pliers or screw driver (to spread cotter pin)
HOW TO MEASURE SCREW SIZE
LENGTH
DIAMETER
CONTENTS OF SHIPPING CARTON
1− Snow Blower
1− Container of Fuel Stabilizer (Located in Parts Bag)
1− Crank Assembly
1− Parts Bag
WARNING: Always wear safety glasses or eye
shields while assembling snow blower.
PARTS BAGS CONTENTS:
1 − Shift Lever Knob
(not actual size)
1 − Washer
1 − Nut
1 − Remote Chute
Knob (not actual size)
1 − Ignition Keys
* 2−1/4−20 x 1.75
* 2−Spacer
* 2−1/4−20
Hex nut
* Non Assembly parts are found in toolbox located on top of belt cover.
ASSEMBLY
10
1741062
Figure 1 shows the snow blower in the shipping position.
Figure 2 shows the snow blower completely assembled.
Reference to right and left hand side of the snow blower is
from the operator’s position at the handle.
UNPACKING
1. Locate the two tear tabs at the bottom of the carton.
2. Pull the tear tape no more than twelve inches (30.48cm.)
at a time. Regrasp tape next to the carton and pull
again. Repeat until all the tape is torn off.
3. After the tape has been completely removed from the
carton, remove the carton from the base. Cut all four cor-
ners and fold the sides toward the center for easy dispos-
al.
4. Remove the plastic bag that covers the unit.
5. Locate and remove the parts bag.
NOTE: Set the fuel stabilizer aside until adding
gasoline to the fuel tank. We recommend that fuel
stabilizer is added to the fuel each time that gasoline
is added to the fuel tank.
6. For shipping purposes, the height adjust skids are at-
tached to the pallet. Remove the screw that secures
each height adjust skid to the pallet. (See Figure 2).
7. Roll the snow blower off the carton by pulling on the lower
handle.
CAUTION: DO NOT back over cables.
8. Remove the packing material from the handle assembly.
9. Cut ties securing the clutch control cables to the lower
handle.
NOTE: If the cables have become disconnected from the
clutch levers, reinstall the cables as shown in Figure 3.
Figure 1
Figure 2
Auger Drive
Lever
Traction Drive Lever
Snow Chute Deflector
Height Adjust
Skid
Auger Housing
Remote Chute Control
Screw
Speed Shifter Lever
Figure 3
”Z” Fitting
Drive Lever
Cable
ASSEMBLY
11
1741062
UPPER HANDLE ASSEMBLY
1. Cut tie holding shift rod to lower handle and move shifter
to the neutral position.
2. Loosen, but do not remove the screws, flatwashers, lock-
washers and hex nuts in the upper holes of the lower han-
dle.
3. Remove the fasteners from the lower holes of the lower
handle See Figure 4.
4. Raise upper handle into operating position. Upper han-
dle should be to the outside of the lower handle.
NOTE: Make sure the cables are not caught between
the upper and lower handle.
NOTE: If the cables have become disconnected form
the drive levers, reinstall the cables as shown in
Figure 5.
5. Install the fasteners that were removed in step 3. DO
NOT tighten until all bolts are in place.
6. Tighten all handle bolts.
Figure 4
Nut
Flatwasher
Bolt
Lockwasher
Figure 5
Lever
“Z” Fitting
Control Cable
CHECK THE CABLES
1. If control cables have become unattached from motor
mount frame, reconnect cables as shown in Figure 6.
2. For cable adjustments, see “How To Check And Adjust
The Cables” in the ADJUSTMENT/REPAIR section.
HOW TO SET
THE LENGTH OF THE CABLES
The cables were adjusted at the factory and no adjustments
should be necessary. However, after the handles are put in
the operating position, the cables can be too tight or too
loose. If an adjustment is necessary, see “How To Check And
Adjust The Cables” in the ADJUSTMENT/REPAIR section.
Traction Drive Cable
Auger Drive Cable
Figure 6
ASSEMBLY
12
1741062
REMOTE CHUTE CONTROL KNOB
1. Thread the knob onto the lever as far as possible. Make
sure that the knob points forward (See Figure 7).
2. Tighten the jam nut against the knob securely.
SPEED SELECT KNOB
1. Thread the knob onto the lever as far as possible. Make
sure that the knob points forward (See Figure 7).
2. Tighten the jam nut against the knob securely.
Figure 7
Nut
Lever
LIp
Knob
HOW TO INSTALL
THE SPEED CONTROL ROD
1. Put the speed select lever to the NEUTRAL position.
See Figure 8.
2. Attach the ball joint, located on the bottom end of the
speed control rod, to the shift yoke assembly. See
Figure 9. The fasteners are attached to the ball joint at
the factory.
3. The length ot the ball joint and speed control rod have
been preadjusted at the factory. If an adjustment is re-
quired, loosen the nut. Remove the fasteners to discon-
nect the ball joint from the shift yoke assembly. To
lengthen or shorten the speed control rod, turn the
adapter to obtain the correct length.
4. Make sure the speed select lever functions correctly.
Move the speed select lever through all speeds.
Speed Select Lever
Figure 8
Remote Chute
Control Lever
Figure 9
Speed Control Rod
Nut
Adapter
Ball Joint
Shift Yoke Assembly
Fasteners
ASSEMBLY
13
1741062
SNOW CHUTE ASSEMBLY
1. Position the snow chute to the INSIDE of the snow
chute flange. Align the three holes in the snow
chute with holes in snow chute flange (see Figure 11).
2. Place three 5/16-18 carriage bolts from the inside of
the chute as shown in figure 11 (hardware is found
in parts bag).
3. Place three 5/16-18 flat washers and three 5/16-18
nuts on the outside of the flange.
4. First tighten the rear carriage bolt, then tighten the
remaining two carriage bolts. Make sure all carriage
bolts are tight.
6. Attach the remote snow chute deflector cable
the cable chute bracket (see Figure 12) and secure
by tightening nuts (on cable) to the cable chute
bracket.
5. Attach the remote snow chute deflector cable to the
weld stud (on deflector) and secure in place using
a pushnut as shown in Figure 12 (pushnut is found
in hardware bag).
.
NOTE: check all carriage bolts in flange for tightness.
DO NOT overtighten.
Figure 10
Figure 11
Snow Chute Deflector
Snow Chute Extension
Flange
Carriage Bolt
Flat Washer
Nut
Snow Chute Deflector Cable
Pushnut
Weld Stud
Snow Chute Deflector Cable
Cable Chute Bracket
Nuts
NOTE: Before starting step 6 make sure that the chute
deflector is in the full open position and the remote
chute lever is in the full open position.
ASSEMBLY
14
1741062
HOW TO ASSEMBLE THE DRIFT CUTTER
Drift cutters are used to cut a path through snow deeper than
the auger housing.
1. Loosen the wingnuts that secure the drift cutters to the
auger housing (see Figure 12).
2. Raise the drift cutters to the desired height.
3. Tighten the wingnuts.
Drift Cutter
Wingnut
Figure 13
HOW TO SET
THE LENGTH OF THE CABLES
The cables were adjusted at the factory and no adjustments
should be necessary. However, after the handles are put in
the operating position, the cables can be too tight or too
loose. If an adjustment is necessary, see “How To Check And
Adjust The Cables” in the Service And Adjustment section.
CHECK THE TIRES
The tires were over inflated for shipment. Check the tire
pressure in the tires. See the sidewall of the tire for the
proper inflation.
IMPORTANT! BEFORE YOU START
OPERATING
r Check the fasteners. Make sure all fasteners are
tight.
r On electric start models, the unit was shipped with
the starter cord plugged into the engine. Before
operating, unplug the starter cord from the engine.
NOTE: This snow blower was shipped WITH OIL in the engine. See “Before Starting Engine” in-
structions in the Operation section of this manual before starting engine.
OPERATION
15
1741062
Get to know your snow blower and its controls. Be sure you (or any other operator) have read and understood the Operation
Precautions listed on page 2 of this manual.
Figure 12
Auger Drive Clutch Lever
Traction Drive
Clutch Lever
Speed Shift Lever
Snow Chute
Deflector
Auger Housing
Height Adjust Skid
Toolbox
Remote Chute Control
Drift
Cutter
Primer Button
Gas Fill
Starter Handle
Throttle Control
Lever
Ignition Key
Choke Lever
Scraper Bar
Shear Pin
Electric
Start Button
Clean-out Tool
Electric Chute Switch
ENGINE AND SNOW BLOWER OPERATING CONTROLS
The engine operating controls and their functions are as
follows:
Throttle Control Lever This snow blower is equipped with
an engine mounted throttle control lever used to start a cold
engine.
Choke Lever Set choke lever to ON CHOKE position to
start a cold engine.
Electric Start Button Used to start the engine using the
120 volt electric starter.
Prime Button Used to inject fuel directly into carburetor
manifold to insure fast starts in cool weather.
Ignition Key Must be inserted into ignition key slot to start
engine. Pull out to stop. Do not turn ignition key.
Starter Handle Starts the engine manually.
The snow blower operating controls and their functions
are as follows:
Speed Select Lever Allows the operator to use one of six
(6) forward and two (2) reverse speeds. To shift, move speed
select lever to desired position.
NOTE: Do not move speed select lever while Traction
Drive Clutch is engaged. This may result in severe
damage to drive system.
Auger Drive Clutch Lever Used to engage and disengage
the auger and impeller. To engage push down, to disengage
release.
Traction Drive Clutch Lever Used to propel snow blower
forward or reverse. Push down to engage, release to
disengage.
Snow Chute Deflector Changes the direction the snow is
blown.
Remote Chute Deflector Lever Pull remote lever back to
discharge snow high and far. Push remote lever forward to
discharge snow down.
Electric Chute Switch Changes the direction of snow
throwing through the discharge chute.
Height Adjust Skid Used to adjust ground clearance of
auger housing (see To Adjust Skid Height in the
Adjustment/Repair section of this manual).
Toolbox Spare shear pins, shear bolt wrenches and
spacers are located in toolbox.
Drift Cutters Cuts a path through snow higher than the
auger housing.
Clean-Out Tool Use the clean-out tool to remove snow and
debirs from the discharge chute and the auger housing.
OPERATION
16
1741062
The operation of any snow blower can result in foreign objects being thrown into the eyes,which can
result in severe eye damage. Always wear safety glasses or eye shields before beginning snow blower
Operation. We recommend standard safety glasses or Wide Vision Safety Mask for over spectacles.
SNOW BLOWER OPERATION
The most effective use of the snow blower will be established
by experience, taking into consideration the terrain, wind
conditions and building location which will determine the
direction of the discharge chute.
NOTE: Do not blow snow towards a building as hidden
objects could be blown with sufficient force to cause
damage.
1. Start the engine as described in section “To Start En-
gine”.
2. Adjust snow chute deflector. Push the remote chute le-
ver forward to discharge snow down, pull remote chute
deflector back to discharge snow high and far. (see
Figure 13).
3. Move the electric chute switch to set the direction (left to
right) of the discharge chute.
4. Select proper speed for snow conditions as outlined be-
low and set speed select lever to desired position.
NOTE: Always release traction drive clutch lever
before moving speed select lever.
Ground speed is determined by snow conditions. Select
the speed you desire by moving the speed selector into
the appropriate colored area on the control panel.
12 Wet, Heavy, Slushy, Extra Deep
3 Moderate
45 Very Light
6 Transport Only
NOTE: When clearing wet, heavy snow, it is
recommended that the ground speed of the unit be
reduced, maintain full throttle and do not attempt to
clear the full width of the unit.
For additional operating instructions see “Operating
Tips” in this section of the manual.
5. Engage auger drive clutch lever (right handFigure 13).
IMPORTANT: Be sure front of unit is clear of
bystanders or obstacles before operating.
6. Engage traction drive clutch lever (left handFigure 13).
As the snow blower starts to move, maintain a firm hold
on the handles and guide the snow blower along the cut-
ting path. Do not attempt to push the snow blower.
7. To stop forward motion, release traction drive clutch lever
(left hand Figure 13).
8. To stop auger, release auger drive clutch lever (right
hand Figure 13).
9. To move the snow blower backwards, move speed select
lever into first or second reverse and engage traction
drive clutch lever (left hand). To stop, release traction
drive clutch lever.
WARNING: Read Owners Manual before oper-
ating machine. This machine can be dangerous
if used carelessly.
Never operate the snow blower without all guards, cov-
ers, and shields in place.
Never direct discharge towards windows or allow by-
standers near machine while engine is running.
Stop the engine whenever leaving the operating posi-
tion.
Disconnect spark plug before unclogging the impeller
housing or the discharge chute and before making re-
pairs or adjustments.
When leaving the machine, remove the ignition key.
To reduce the risk of fire, keep the machine clean and
free from spilled gas, oil and debris.
Auger Drive Lever
Traction Drive LeverShift Lever
Remote Chute Lever
Figure 13
Electric Chute
Switch
OPERATION
17
1741062
BEFORE STARTING ENGINE
Check the oil
NOTE: The engine was shipped from the factory filled
with oil. Check the level of the oil. Add oil as needed.
1. Make sure the unit is level.Use a high quality detergent
oil classified “For Service SG, SH, SJ, SL, or higher”.
2. Remove the oil fill cap/dipstick and wipe with a clean
cloth (see Figure 14).
3. Insert the oil fill cap/dipstick and turn clockwise to tighten.
4. Remove the oil fill cap/dipstick and check the oil.
NOTE: Do not check the level of the oil while the
engine runs.
5. If necessary, add oil until the oil reaches the FULL mark
on the oil fill/cap dipstick (see Figure 14). Do not add too
much oil.
6. Tighten the fill cap/dipstick securely each time you check
the oil level.
NOTE: For extreme cold operating conditions of 0F
(18 C) and below, use a synthetic 5W30 motor oil for
easier starting.
NOTE: S.A.E. 5W30 motor oil may be used to make
starting easier in areas where the temperature is 20 F.
(7 C) to 0F (18 C). Synthetic 5W30 is acceptable for
all temperatures. DO NOT mix oil with gasoline.
NOTE: SEE CHART FOR OIL RECOMMENDATION
0F (18 C) and below
0F (18 C) and above
TYPE OF OILTEMPERATURE
synthetic 5W30
S.A.E. 5W30
F 20 0 20 32 40
C 30 20 10 0 10
SAE VISCOSITY GRADES
5W30
synthetic 5W30
FILL GAS
This engine is certified to operate on gasoline. Exhaust
Emission Control System: EM (Engine Modifications)
1. Fill the fuel tank with fresh, clean, unleaded regular, un-
leaded premium, or reformulated automotive gasoline
with a minimum of 85 octane along with a fuel stabilizer
(follow instructions on fuel stabilizer package). DO NOT
use leaded gasoline. We recommend that fuel stabilizer
be added to the fuel each time that gasoline is added to
the fuel tank.
NOTE: Winter grade gasoline has higher volatility to
improve starting. Be certain container is clean and
free from rust or other foreign particles. Never use
gasoline that may be stale from long periods of
storage in the container.
CAUTION: DO NOT use gasoline containing any
amount of alcohol as it can cause serious damage to
the engine or significantly reduce the performance.
2. Check to make sure that spark plug is tightened securely
into engine and spark plug wire is attached to spark plug.
If torque wrench is available, torque plug to 1823 ftlbs.
WARNING: Gasoline is flammable. Always use
caution when handling or storing gasoline. Do
not add gasoline to the fuel tank while snow
blower is running, hot, or when snow blower is in an en-
closed area. Keep away from open flame, electrical
sparks and DO NOT SMOKE while filling the fuel tank.
Never fill the fuel tank completely; but fill the fuel tank
to within 1-1/2 inch (3.8 mm) from the top to provide
space for the expansion of the fuel. Always fill fuel tank
outdoors and use a funnel or spout to prevent spilling.
Make sure to wipe up any spilled fuel before starting
the engine.
Store gasoline in a clean, approved container, and keep
the cap in place on the container. Keep gasoline in a
cool well ventilated place; never in the house. Never
buy more than a 30 day supply of gasoline to assure
volatility. Gasoline Is intended to be used as a fuel for
internal combustion engines; therefore, do not use
gasoline for any other purpose. Since many children
like the smell of gasoline, keep it out of their reach be-
cause the fumes are dangerous to inhale, as well as be-
ing explosive.
FULL
Figure 14
Oil Fill Cap/Dipstick
Fuel Tank
BEFORE STOPPING THE ENGINE
Run the engine for a few minutes to help dry off any moisture
on the engine.
OPERATION
18
1741062
TO STOP ENGINE
WARNING
Gasoline and its vapors are extremely
flammable and explosive.
Fire or explosion can cause severe burns or
death.
DO NOT choke the carborator to stop the
engine.
1. Move the stop switch (A, Figure 15) to the stop
position.
2. Remove the safety key (B). Keep the safety key
out of reach of children.
A
B
Figure 15. Stopping the Engine
A. On/Stop Switch
B. Safety Key
STARTING THE ENGINE
1. Check the oil level. See the Engine Manual
How
to Check/Add Oil
section
2. Make sure equipment drive controls are
disengaged.
3. Push the stop switch to the on position (A, Figure
6).
A
Figure 6. On/Stop Switch
A. On/Stop Switch Selector
4. Insert the engine key (A, Figure 17 ) into the engine
key slot and push fully in to the RUN position.
5. Turn the choke knob (B) fully clockwise if engine is
cold.
Note: Do not use the choke to start a warm engine.
6. Push the primer button (C) two times.
Note: Do not use the primer to start a warm engine.
Note: If the engine does not start after three attempts,
see the Engine Manual Troubleshooting section.
8. Electric Start: First connect the extension cord to
the power cord receptacle and then into a wall
receptacle. If additional extension cord is
required, make sure it is 3-wire.
Figure 18. Rewind Start
A. Starter Cord Handle
Figure 17. Rewind Start
A. Engine Key
B. Choke Knob
C. Primer Button
A
WARNING
Rapid retraction of the starter cord (kickback)
will pull your hand and arm toward the engine
faster than you can let go. Broken bones,
fractures, bruises or sprains could result.
When starting engine, pull the starter cord
slowly until resistance is felt and then pull
rapidly to avoid kickback.
C
A
B
7. Rewind Start: Firmly hold the starter cord handle
(A, Figure 18). Pull the starter cord handle slowly
until resistance is felt, then pull rapidly.
OPERATION
19
1741062
WARNING
If the extension cord is damaged, it must be
replaced by the manufacturer or its service
agent or a similarly qualified person to avoid to
avoid a hazard.
9. Electric Start: Depress the push button (A, Figure
19). After you start the engine, first disconnect the
extension cord from the wall receptacle and then
from the power cord receptacle (B).
CAUTION
To extend the life of the starter, use short
starting cycles (five seconds maximum.) Wait
one minute between starting cycles.
A
B
Figure 19. Electric Start
A. Starter Push Button
B. Power Cord Receptacle
Note: If the engine does not start after three attempts,
see the Engine Manual Troubleshooting section.
OPERATION
20
1741062
FROZEN STARTER
If the starter is frozen and will not turn engine:
1. Pull as much rope out of the starter as possible.
2. Release the starter handle and let it snap back against
the starter. Repeat until the engine starts.
Warm engines will cause condensation in cold weather. To
help prevent possible freezeup of recoil starter and engine
controls, proceed as follows after each snow removal job.
1. With engine off, allow engine to cool for several minutes.
2. Pull starter rope very slowly until resistance is felt, then
stop. Allow the starter rope to recoil. Repeat three times.
3. With the engine not running, wipe all snow and moisture
from the carburetor cover in area of control levers. Also
move choke knob and starter handle several times.
4. With engine not running, wipe all snow and moisture from
carburetor cover in area of control levers. Also move
control levers backward and forward several times.
WARNING: Never run engine indoors or in en-
closed, poorly ventilated areas. Engine exhaust
contains CARBON MONOXIDE, AN ODORLESS
AND DEADLY GAS. Keep hands, feet, hair and loose
clothing away from any moving parts on engine and
snow thrower.
S Engine parts, especially the muffler, become ex-
tremely hot. Severe thermal burns can occur on con-
tact. Allow the engine to cool before touching.
S Never allow children to operate the snow thrower.
Never allow adults to operate the snow blower with-
out proper instruction.
S Keep the area of operation clear of all persons, partic-
ularly small children and pets.
S Never leave the snow blower unattended while the
engine is running. Anyone operating the engine or
equipment must carefully read and understand the
operating instructions.
IMPORTANT: After each use of the snow blower, stop the
engine, remove the safetey/ignition key, remove all
accumulated snow from the snow blower and wipe
clean. Store the snow blower in a protected area.
NOTE: Never cover snow blower while engine and
exhaust area are still warm.
HOW TO CLEAR
A CLOGGED DISCHARGE CHUTE
WARNING: Hand contact with the rotating im-
peller inside the discharge chute is the most
common cause of injury associated with snow
blowers. NEVER USE YOUR HAND TO CLEAN OUT
THE DISCHARGE CHUTE.
To Clear The Chute:
S SHUT OFF THE ENGINE!
S Wait 10 seconds to be sure that the impeller blades
have stopped rotating.
S Always use a clean-out tool, not your hands.
A clean-out tool is attached to either the handle or the top of
the auger housing (see Figure 20). Use the clean-out tool to
remove snow from the auger housing.
How To Use The Clean-Out Tool
Release the auger drive lever.
Pull out the safety key.
Disconnect spark plug wire.
Do not place your hands in the auger or discharge
chute. Use a clean-out tool to remove snow or debris.
WARNING: Blockage must be cleared only after
shutting off the snow blower and only with a
clean-out tool, not by hand.
Figure 20
Clean-out Tool
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78

Simplicity 6271200X43 Manuel utilisateur

Catégorie
Souffleuses à neige
Taper
Manuel utilisateur
Ce manuel convient également à

dans d''autres langues