Poulan Pro HDF900 Le manuel du propriétaire

Marque: Poulan Pro

Modèle: HDF900

Catégorie: Mini motoculteurs

Taper: Le manuel du propriétaire

OPERATOR'S MANUAL

MODEL:

HDF900

FRONT TINE TILLER

ALWAYS WEAR EYE PROTECTION DURING OPERATION

Visit our website: www.poulan-pro.com

WARNING:

Read this Man u al and follow all

Warnings and Safety Instructions.

Fail ure to do so can re sult in seri-

ous in ju ry.

IMPORTANT MANUAL Do Not Throw Away

427896 03.23.09 CL Printed in U.S.A.

• Keep children and pets away.

• Do not overload the machine capacity by attempting

to till too deep at too fast a rate.

• Never operate the machine at high speeds on slippery

surfaces. Look behind and use care when backing.

• Never allow bystanders near the unit.

• Use only attachments and accessories approved by

the manufacturer of the tiller.

• Never operate the tiller without good visibility or light.

• Be careful when tilling in hard ground. The tines may

catch in the ground and propel the tiller forward. If this

occurs, let go of the handlebars and do not restrain the

machine.

MAINTENANCE AND STORAGE

• Keep machine, attachments, and accessories in safe

work ing condition.

• Check shear pins, engine mounting bolts, and other

bolts at frequent intervals for proper tightness to be

sure the equip ment is in safe working condition.

• Never store the machine with fuel in the fuel tank inside

a building where ignition sources are present, such

as hot water and space heaters, clothes dryers, and

the like. Allow the engine to cool before storing in any

enclosure.

• Always refer to the operator’s guide instructions for

im por tant details if the tiller is to be stored for an ex-

tended period.

- IMPORTANT -

CAUTIONS, IMPORTANTS, AND NOTES ARE A MEANS OF

ATTRACTING ATTENTION TO IMPORTANT OR CRIT I CAL

IN FOR MA TION IN THIS MANUAL.

IMPORTANT: USED TO ALERT YOU THAT THERE IS A

POS SI BIL I TY OF DAM AG ING THIS EQUIP MENT.

NOTE: Gives essential information that will aid you to

better un der stand, incorporate, or execute a particular set

of instructions.

Look for this symbol to point out im-

por tant safety precautions. It means

CAUTION!!! BE COME ALERT!!! YOUR

SAFE TY IS INVOLVED.

CAUTION: Always disconnect spark

plug wire and place wire where it can-

not contact spark plug in order to pre-

vent ac ci den tal starting when setting

up, trans port ing, adjusting or making

re pairs.

SAFETY RULES

Safe Operation Practices for Walk-Behind Powered Ro ta ry Tillers

TRAINING

• Read the Owner’s Manual care ful ly. Be thor ough ly

fa mil iar with the controls and the proper use of the

equip ment. Know how to stop the unit and disengage

the controls quickly.

• Never allow children to operate the equipment. Never

allow adults to op er ate the equipment without proper

instruction.

• Keep the area of operation clear of all persons, par-

tic u lar ly small children, and pets.

PREPARATION

• Thoroughly inspect the area where the equipment is

to be used and remove all foreign objects.

• Disengage all clutches and shift into neutral before

starting the engine (mo tor).

• Do not operate the equipment with out wearing ad e -

quate outer gar ments. Wear footwear that will im prove

footing on slippery surfaces.

• Handle fuel with care; it is highly flammable.

• Use an approved fuel container.

• Never add fuel to a running engine or hot engine.

• Fill fuel tank outdoors with extreme care. Never fill fuel

tank indoors.

• Replace gasoline cap securely and clean up spilled

fuel before restarting.

• Use extension cords and receptacles as specified by

the manufacturer for all units with electric drive motors

or electric starting motors.

• Never attempt to make any adjustments while the

engine (motor) is running (except where specifically

rec om mend ed by manufacturer).

OPERATION

• Do not put hands or feet near or under rotating parts.

• Exercise extreme caution when op er at ing on or cross-

ing gravel drives, walks, or roads. Stay alert for hidden

hazards or traffic. Do not carry pas sen gers.

• After striking a foreign object, stop the engine (motor),

remove the wire from the spark plug, thoroughly in spect

the tiller for any damage, and repair the damage before

restarting and op er at ing the tiller.

• Exercise caution to avoid slipping or falling.

• If the unit should start to vibrate ab nor mal ly, stop the

engine (motor) and check immediately for the cause.

Vi bra tion is generally a warning of trouble.

• Stop the engine (motor) when leaving the operating

position.

• Take all possible precautions when leav ing the ma chine

unattended. Disengage the tines, shift into neutral, and

stop the engine.

• Before cleaning, repairing, or inspecting, shut off the

engine and make certain all moving parts have stopped.

Disconnect the spark plug wire, and keep the wire away

from the plug to prevent accidental starting. Disconnect

the cord on electric motors.

• Do not run the engine indoors; exhaust fumes are

dangerous.

• Never operate the tiller without proper guards, plates,

or other safety protective devices in place.

WARNING

The engine exhaust from this product con-

tains chem i cals known to the State of Cal i -

for nia to cause cancer, birth defects, or other

reproductive harm.

PRODUCT SPECIFICATIONS

CONGRATULATIONS on your purchase of a new tiller. It

has been designed, en gi neered and manu fac tured to give

you the best pos sible de penda bil ity and per form ance.

Should you experience any prob lems you can not easily

remedy, please contact your nearest authorized service

center. We have com pe tent, well-trained tech ni cians and

the proper tools to service or repair this unit.

Please read and retain this manual. The in struc tions will

enable you to assemble and main tain your tiller prop erly.

Always observe the “SAFETY RULES”.

IMPORTANT: THIS UNIT IS EQUIPPED WITH AN INTERNAL

COMBUSTION ENGINE AND SHOULD NOT BE USED ON

OR NEAR ANY UNIMPROVED FOREST-COVERED, BRUSH-

COVERED OR GRASS COVERED LAND UNLESS THE

ENGINE'S EXHAUST SYSTEM IS EQUIPPED WITH A SPARK

ARRESTER MEETING APPLICABLE LOCAL LAWS (IF ANY).

IF A SPARK ARRESTER IS USED, IT SHOULD BE MAINTAINED

IN EFFECTIVE WORK ING ORDER BY THE OPERATOR.

IN THE STATE OF CALIFORNIA, A SPARK ARRESTER IS

REQUIRED BY LAW (SECTION 4442 OF THE CALIFORNIA

PUBLIC RESOURCES CODE). OTHER STATES MAY HAVE

SIMILAR LAWS. FEDERAL LAWS APPLY ON FEDERAL LANDS.

SEE YOUR AUTHORIZED SERVICE CENTER/DEPARTMENT

FOR SPARK ARRESTER.

CUSTOMER RESPONSIBILITIES

• Read and observe the safety rules.

• Follow a regular schedule in maintaining, caring for

and using your tiller.

• Follow instructions under “Maintenance” and “Stor age”

sections of this Manual.

MAINTENANCE .....................................................10-12

SERVICE & ADJUSTMENTS ................................. 13-15

STORAGE .................................................................... 16

TROUBLESHOOTING ................................................. 17

WARRANTY ................................................................. 19

SAFETY RULES ............................................................ 2

PRODUCT SPECIFICATIONS ....................................... 3

CUSTOMER RESPONSIBILITIES ................................. 3

ASSEMBLY ................................................................. 4-5

OPERATION ............................................................... 6-9

MAINTENANCE SCHEDULE ...................................... 10

TABLE OF CONTENTS

Gasoline Capacity: 3 Quarts (2.8L)

Unleaded Reg u lar

Oil (API-SG-SL): SAE 30 (Above 32°F)

(Capacity: 20 oz./0.6L) SAE 5W-30 (Below 32°F)

Spark Plug : NGK-BPR6ES

(Gap: .030"/0.76mm) TORCH-F6RTC

ASSEMBLY

OPERATOR’S POSITION (See Fig. 1)

When right or left hand is mentioned in this manual, it

means when you are in the operating position (standing

behind tiller handles).

Your new tiller has been assembled at the factory with exception of those parts left unassembled for shipping purposes.

To ensure safe and proper operation of your tiller all parts and hardware you assemble must be tightened securely. Use

the correct tools as necessary to insure proper tightness.

TOOLS REQUIRED FOR ASSEMBLY

A socket wrench set will make assembly easier. Standard

wrench sizes are listed.

(1) Utility knife

(1) Screwdriver

(2) 1/2" wrenches

OPERATOR'S POSITION

RIGHT

FRONT

LEFT

overhead_views_8

Fig. 1

(6) Lock Washers 5/16

(6) Hex Nuts 5/16-18

(4) Hex Bolts 5/16-18 x 1-1/4

(2) Hex Bolts 5/16-18 x 1

(4) Washers 3/8 x 7/8 x 14

CONTENTS OF HARDWARE PACK

UNPACK CARTON & INSTALL HANDLE

(See Fig. 2)

CAUTION: Be careful of exposed

sta ples when handling or disposing

of cartoning material.

IMPORTANT: WHEN UNPACKING AND AS SEM BLING

TILLER, BE CAREFUL NOT TO STRETCH OR KINK

CABLE(S).

• Cut cable ties securing handles.

• Slowly lift handle as sem bly up, route cable(s) as shown

and align han dle holes with handle panel hole and

slot.

• Loosely assemble hardware as shown. Be sure the

shorter (1" long) hex bolt is assembled in lower hole of

handle. Repeat for opposite side. Tight en all hard-

ware se cure ly.

• Cut cable ties securing tiller to skid and remove tiller

from skid.

• Remove screws securing depth stake to skid and dis-

card the screws.

dep

th_st

ake_4

DEPTH

STAKE

SUPPORT

BOLT

HEX BOLTS,

LOCK WASH ERS,

AND HEX NUTS

DEPTH STAKE

SUPPORT

NUT “A”

ENGINE BRACK ET

HALVES

Fig. 3

STAKE

SPRING

TILLER

HANDLES

020

CABLE(S)

Fig. 2

&4(ANDLEª0ANEL?

HANDLE

PANEL

BOLTS

FLAT

WASHER

HEX BOLT

5/16-18X1"

TILLER

HANDLE

HAN DLE

PANEL

NUT

LOCK

WASH ER

HEX BOLT

5/16-18X1-1/4"

ASSEMBLY

HANDLE HEIGHT

• Handle height may be adjusted to better suit operator.

(See “HANDLE HEIGHT” in the Service and Ad just -

ments section of this manual).

TILLING WIDTH

• Tilling width may be adjusted to better handle your

tilling con di tions (See “TINE ARRANGEMENT” in the

Service and Adjustments section of this manual).

TINE OPERATION

• Check tine operation before first use. (See “TINE OP-

ERATION CHECK” in the Service and Adjustments

section of this manual).

INSTALL DEPTH STAKE AS SEM BLY

(See Fig. 3)

• Loosen nut “A”.

• Insert stake support between engine brack et halves

with stake spring down.

• Bolt stake support to engine brackets with bolts, lock

washers and nuts. Tight en se curely. Tighten nut “A”.

• Depth stake must move freely. If it does not, loosen

support bolt.

RECOIL

STARTER

HANDLE

DEPTH STAKE

TINE

SHIELD

FORWARD TINE

CONTROL

TINES

FUEL

VALVE

ON/OFF

SWITCH

THROTTLE CONTROL

CHOKE CONTROL

KNOW YOUR TILLER

READ THIS MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TILLER.

Compare the illustrations with your tiller to familiarize yourself with the location of various controls and adjustments. Save

this manual for future reference.

These symbols may appear on your Tiller or in literature supplied with the product. Learn and understand their mean-

ing.

Fig. 4

MEETS ANSI SAFETY REQUIREMENTS

Our tillers conform to the safety standards of the American National Standards Institute.

CHOKE CONTROL - Used when starting a cold engine.

DEPTH STAKE - Controls forward speed and the depth at

which the tiller will dig.

ENGINE ON/OFF SWITCH - The engine switch enables

and disables the ignition system.

FUEL VALVE - The fuel valve opens and closes the

passage between the fuel tank and the carburetor.

OPERATION

FORWARD TINE CONTROL - Engages tines in forward

direction.

RECOIL STARTER HANDLE - Used to start the engine.

direction.

THROTTLE CONTROL - Controls engine speed.

The operation of any tiller can result in foreign objects thrown into the eyes, which can result

in severe eye damage. Always wear safety glasses or eye shields before starting your tiller

and while tilling. We recommend a wide vision safety mask for over spectacles or standard

safety glasses.

TILLING

The speed and depth of tilling is regulated by the position

of the depth stake and wheel height.

The depth stake should always be below the wheels for

digging. It serves as a brake to slow the tiller’s forward

motion to enable the tines to penetrate the ground. Also,

the more the depth stake is lowered into the ground the

deeper the tines will dig.

DEPTH STAKE (See Fig. 6)

Adjust depth stake by removing the hairpin clip and clevis

pin. Change depth stake to desired position. Replace the

clevis pin and hairpin clip.

• For normal tilling, set depth stake at the second or third

hole from the top.

WHEELS (See Fig. 6)

Adjust wheels by removing the hairpin clip and clevis pin.

Change wheel position. Replace the hairpin clip and clevis

pin.

• For normal tilling, set wheels at the second or third

hole from the top.

dep

th_stake_

DEPTH

STAKE

SPRING

HAIRPIN CLIP

AND CLEVIS PIN

WHEEL

Fig. 6

OPERATION

HOW TO USE YOUR TILLER

Know how to operate all controls before adding fuel and

oil or attempting to start engine.

STOPPING (See Fig. 5)

TINES

1. Release tine control to stop move ment.

ENGINE

2. Move throttle control to “SLOW” po si tion and allow the

engine to run slowly for cool down.

3. Turn the engine switch to the "OFF" Position.

4. Turn the fuel valve lever to the "OFF" Position.

NOTE: NEVER USE CHOKE TO STOP ENGINE.

IMPORTANT: TO STOP ENGINE IN AN EMERGENCY, TURN

THE ENGINE SWITCH TO THE OFF POSITION.

Tine Control

“Off” (UP) Po si tion

Tine Control

“On” (DOWN) Po si tion

TINE OPERATION

• Squeeze tine control to handle.

Throttle

Control

Engine

Switch

Fuel Valve

Throttle

Control

Fuel

Valve

Engine

Switch

Fig. 5

TO TRANSPORT

CAUTION: Before lifting or trans port ing,

allow tiller engine and muffler to cool.

Disconnect spark plug wire. Drain

gasoline from fuel tank.

AROUND THE YARD

• Tip depth stake forward until it is held by the stake

spring.

• Push tiller handles down, raising tines off the ground.

• Push or pull tiller to desired location.

AROUND TOWN

• Disconnect spark plug wire.

• Drain fuel tank.

• Transport in upright position to prevent oil leakage.

Fig. 7

OPERATION

ADD GASOLINE

• Fill fuel tank to bottom of filler neck. Do not overfill.

Use fresh, clean, regular un lead ed gasoline with a

minimum of 87 octane. (Use of leaded gasoline will

increase carbon and lead oxide deposits and reduce

valve life). Do not mix oil with gasoline. Purchase fuel

in quan ti ties that can be used within 30 days to assure

fuel freshness.

CAUTION: Fill to within 1/2 inch of top

of fuel tank to prevent spills and to allow

for fuel expansion. If gasoline is ac-

ci den tal ly spilled, move machine away

from area of spill. Avoid creating any

source of ignition until gasoline vapors

have disappeared.

Wipe off any spilled oil or fuel. Do not

store, spill or use gasoline near an

open flame.

IMPORTANT: WHEN OPERATING IN TEMPERATURES

BELOW32°F(0°C), USE FRESH, CLEAN WINTER GRADE

GAS O LINE TO HELP INSURE GOOD COLD WEATHER

START ING.

CAUTION: Alcohol blended fuels (called

gas o hol or using ethanol or methanol) can at-

tract moisture which leads to sep a ra tion and

for ma tion of acids during storage. Acidic gas

can damage the fuel system of an engine while

in storage. To avoid engine problems, the fuel

system should be emptied before stor age of

30 days or longer. Drain the gas tank, start

the engine and let it run until the fuel lines

and carburetor are empty. Use fresh fuel next

sea son. See Storage In struc tions for additional

information. Never use engine or carburetor

cleaner products in the fuel tank or permanent

damage may occur.

BEFORE STARTING ENGINE

IMPORTANT: BE VERY CAREFUL NOT TO ALLOW DIRT TO

ENTER THE ENGINE WHEN CHECKING OR ADDING OIL

OR FUEL. USE CLEAN OIL AND FUEL AND STORE IN AP-

PROVED, CLEAN, COVERED CON TAIN ERS. USE CLEAN

FILL FUNNELS.

FILL ENGINE WITH OIL (SEE Fig. 7)

1. Remove hangtag from engine.

2. With engine level, remove engine oil fill er plug.

3. Fill engine with oil to point of over flow ing. For ap proxi-

mate ca pac i ty see “PROD UCT SPEC I FI CA TIONS” on

page 4 of this manual. All oil must meet A.P.I. Service

Classification SG-SL.

4. Tilt tiller back on its wheels and then re-level.

5. With engine level, refill to point of over flow ing if nec-

es sary. Re place oil filler plug.

• For cold weather operation you should change oil for

easier starting (See “OIL VISCOSITY CHART” in the

Main te nance section of this man u al).

• To change engine oil, see the Main te nance section of

this manual.

ngi

e_ar

Oil Level

Oil Filler Plug

Max Upper Level

Min Lower Level

TO START ENGINE (SEE Fig. 8)

CAUTION: KEEP TINE CONTROL IN “OFF”

PO SI TION WHEN STARTING ENGINE.

When starting engine for the first time or if engine has run

out of fuel, it will take ex tra pulls of the recoil starter to

move fuel from the tank to the engine.

1. Make sure spark plug wire is prop er ly connected.

2. Place the fuel valve to the "ON" position.

3. To start a cold engine, move the choke lever to the

"ON" position.

4. Move the throttle lever away from the "SLOW" position,

about 1/3 of the way toward the "FAST" position.

5. Turn the engine switch to the "ON" position. Pull rope

out slowly until engine reaches start of com pres sion

cy cle (rope will pull slightly harder at this point).

6. Pull recoil starter handle quickly. Do not let starter

handle snap back against starter. Repeat if neces-

sary.

NOTE: IF ENGINE FIRES BUT DOES NOT START, MOVE

CHOKE CONTROL TO HALF CHOKE POSITION. PULL

RECOIL STARTER HANDLE UNTIL ENGINE STARTS.

7. If the choke lever has been moved to the "ON" position

to start the engine, gradually move it to the opposite

position as the engine warms up.

NOTE: A WARM ENGINE REQUIRES LESS

CHOK ING TO START.

8. Move throttle control to desired running position.

9. Allow engine to warm up for a few min utes before

engaging tines.

BREAKING IN YOUR TILLER

Break-in your belt(s), pulleys and tine control before you

actually begin tilling.

• Start engine, tip tines off ground by pressing handles

down and engage tine control to start tine rotation.

Allow tines to rotate for five minutes.

• Check tine operation and adjust if necessary. See “TINE

OPERATION CHECK” in the Service and Ad just ments

sec tion of this manual.

TILLING HINTS

CAUTION: Until you are accustomed

to handling your tiller, start ac tu al field

use with throttle in slow position.

To help tiller move forward, lift up the handles slightly (thus

lifting depth stake out of ground). To slow down the tiller,

press down on handles.

If you are straining or tiller is shaking, the wheels and depth

stake are not set properly in the soil being tilled. The proper

setting of the wheels and depth stake is through trial and

error and depends upon the soil con di tion. (The harder or

wetter the ground, the slower the engine and tine speed

needed. Under these poor con di tions, at fast speed the

tiller will run and jump over the ground).

A properly adjusted tiller will dig with little effort from the

operator.

• Tilling is digging into, turning over, and breaking up

packed soil before planting. Loose, unpacked soil helps

root growth. Best tilling depth is 4"-6". A tiller will also

clear the soil of unwanted vege ta tion. The de com po si tion

of this vegetable mat ter en rich es the soil. De pend ing

on the climate (rain fall and wind), it may be advisable

to till the soil at the end of the growing season to further

condition the soil.

• Soil conditions are important for proper tilling. Tines will

not readily penetrate dry, hard soil which may con trib ute

to excessive bounce and difficult handling of your tiller.

Hard soil should be mois tened before tilling; however,

extremely wet soil will “ball-up” or clump during tilling.

Wait until the soil is less wet in order to achieve the

best results. When tilling in the fall, remove vines and

long grass to prevent them from wrapping around the

tine shaft and slowing your tilling operation.

• You will find tilling much easier if you leave a row

untilled between passes. Then go back between tilled

rows. (See Fig. 9) There are two reasons for doing

this. First, wide turns are much easier to negotiate than

about-faces. Sec ond, the tiller won’t be pulling itself,

and you, toward the row next to it.

• Set depth stake and wheel height for shallow tilling

when working extremely hard soil or sod. Then work

across the first cuts at normal depth.

321

Fig. 9

CULTIVATING

Cultivating is destroying the weeds between rows to pre-

vent them from robbing nourishment and moisture from the

plants. At the same time, breaking up the upper layer of

soil crust will help retain moisture in the soil. Best digging

depth is 1"-3".

• You will probably not need to use the depth stake. Begin

by tipping the depth stake forward until it is held by the

stake spring.

• Cultivate up and down the rows at a speed which will

allow tines to uproot weeds and leave the ground in

rough con di tion, promoting no fur ther growth of weeds

and grass (See Fig. 10).

Fig. 10

OPERATION

Throttle Control

Engine

Switch

Choke

Con trol

Fuel Valve

Recoil Starter

Spark Plug

Fig. 8

MAINTENANCE

cSAE 30 OR 10W-30 MOTOR OIL

dREFER TO MAINTENANCE “ENGINE” SECTION

LUBRICATION CHART

d EN GINE

c TINE CON TROL

c IDLER

ARM

GENERAL RECOMMENDATIONS

The warranty on this tiller does not cover items that have

been subjected to operator abuse or negligence. To receive

full value from the warranty, the operator must main tain tiller

as instructed in this manual.

Some adjustments will need to be made periodically to

properly maintain your tiller.

At least once a season, check to see if you should make

any of the adjustments described in the Service and Ad-

justments section of this manual.

• Once a year you should replace the spark plug, clean

or replace air filter, and check tines and belts for wear.

A new spark plug and clean air filter assure proper

air-fuel mixture and help your engine run better and

last longer.

BEFORE EACH USE

• Check engine oil level.

• Check tine operation.

• Check for loose fasteners.

LUBRICATION

Keep unit well lubricated (See “LUBRICATION CHART”).

-!).4%.!.#%

3#(%$5,%

&),,ª).ª$!4%3

!3ª9/5ª#/-0,%4%

2%'5,!2ª3%26)#%

#HECKª%NGINEª/ILª,EVEL

#HANGEª%NGINEª/IL

/ILª0IVOTª0OINTS

)NSPECTª!IRª3CREEN

)NSPECTª3PARKª!RRESTERªª-UFFLER

#LEANªORª2EPLACEª!IRª#LEANERª#ARTRIDGE

#LEANª%NGINEª#YLINDERª&INS

2EPLACEª3PARKª0LUG

"%&/2%ª%!#(ª53%

%6%29ªª(/523

%6%29ªª(/523

%6%29ªª(/523

3%26)#%ª$!4%3





ªª#HANGEªMOREªOFTENªWHENªOPERATINGªUNDERªAªHEAVYªLOADªORªINªHIGHªAMBIENTªTEMPERATURES

ªª3ERVICEªMOREªOFTENªWHENªOPERATINGªINªDIRTYªORªDUSTYªCONDITIONSª

MAINTENANCE

Disconnect spark plug wire before performing any maintenance (except car bu re tor adjustment) to

prevent accidental start ing of engine.

Prevent fires! Keep the engine free of grass, leaves, spilled oil, or fuel. Re move fuel from tank

before tipping unit for maintenance. Clean muffler area of all grass, dirt, and debris.

Do not touch hot muffler or cylinder fins as contact may cause burns.

ENGINE

LUBRICATION

Use only high quality detergent oil rated with API service

classification SF-SJ. Select the oil’s SAE vis cos i ty grade

according to your expected temperature. (See Fig. 10)

Fig. 11

NOTE: Although multi-viscosity oils (5W-30, 10W-30, etc.)

improve starting in cold weather, they will result in increased

oil consumption when used above 32°F (0°C). Check your

engine oil level more frequently to avoid possible engine

damage from running low on oil.

Change the oil after every 25 hours of operation or at

least once a year if the tiller is not used for 25 hours in

one year.

Check the crankcase oil level before starting the engine

and after each five (5) hours of continuous use. Add SAE

30 motor oil or equivalent. Tighten oil filler plug securely

each time you check the oil level.

4%-0%2!452%ª2!.'%ª!.4)#)0!4%$ª"%&/2%ª.%84ª/),ª#(!.'%

ªªªªªªªªªªªªªªªªªªªªªªªªªªªªªªªªªªªª3!%ª6)3#/3)49ª'2!$%3

CAUTION:Disconnect spark plug wire

before performing any maintenance to

prevent accidental start ing of engine.

Prevent fires! Keep the engine free of

grass, leaves, spilled oil, or fuel. Re-

move fuel from tank before tipping unit

for maintenance. Clean muffler area of

all grass, dirt, and debris. Do not touch

hot muffler or cylinder fins as contact

may cause burns.

TO CHANGE ENGINE OIL (See Figs. 11 and 12)

Determine temperature range expected before oil change.

All oil must meet API service classification SF-SJ.

• Be sure tiller is on level surface.

• Oil will drain more freely when warm.

• Catch oil in a suitable container.

• Remove drain plug.

• Tip tiller forward to drain oil.

Oil

Drain

Plug

Oil Filler Plug

Oil Level

Fig. 12

• After oil has drained completely, replace oil drain plug

and tighten securely.

• Remove oil filler plug. Be careful not to allow dirt to

enter the engine.

• Refill engine with oil. See “FILL ENGINE WITH OIL ”

in the Operation section of this manual.

AIR CLEANER (See Fig. 13)

Service air cleaner cartridge every twenty-five hours, more

often if engine is used in very dusty conditions.

• Loosen air cleaner screws, one on each side of cover.

• Remove air cleaner cover.

• Carefully remove air cleaner cartridge. Be care ful. Do

not allow dirt or de bris to fall into carburetor.

• Clean by tapping gently on a flat surface.

• If very dirty or damaged, replace cartridge.

• Clean and re place cover. Tighten screws securely.

IMPORTANT: PETROLEUM SOLVENTS, SUCH AS KER O SENE,

ARE NOT TO BE USED TO CLEAN THE CAR TRIDGE. THEY

MAY CAUSE DETERIORATION OF THE CARTRIDGE. DO

NOT OIL CARTRIDGE. DO NOT USE PRESSURIZED AIR TO

CLEAN OR DRY CARTRIDGE.

Fig. 13

Air Cleaner

Screws

Cover

Air Clean er

Car tridge

Pre-Cleaner

MAINTENANCE

Fig. 14

MUFFLER

Do not operate tiller without muffler. Do not tamper with

exhaust system. Damaged mufflers or spark arresters

could create a fire hazard. Inspect pe ri odi cally and re place

if nec es sary. If your engine is equipped with a spark arrester

screen assembly, re move every 50 hours for cleaning and

inspection. Re place if dam aged.

SPARK PLUG

Replace spark plugs at the beginning of each tilling sea-

son or after every 25 hours of use, whichever comes first.

Spark plug type and gap setting are shown in “PROD UCT

SPEC I FI CA TIONS” on page 4 of this manual.

TRANSMISSION

Your transmission is sealed and will not re quire lubrication

unless serviced.

CLEANING

Do not clean your tiller when the engine and transmission

are hot. We do not rec om mend using pressurized water

(gar den hose, etc.) to clean your unit un less the gasket

area around the trans mis sion and the engine muf fler, air

fil ter and car bu re tor are cov ered to keep wa ter out. Wa ter

in en gine will short en the useful life of your tiller.

• Clean engine, wheels, finish, etc. of all foreign matter.

• Keep finished surfaces and wheels free of all gas o line,

oil, etc.

• Protect painted surfaces with au to mo tive type wax.

COOLING SYSTEM (See Fig. 14)

Your engine is air cooled. For proper en gine performance

and long life keep your engine clean.

• Clean air screen frequently using a stiff-bristled brush.

• Remove blower housing and clean as nec es sary.

• Keep cylinder fins free of dirt and chaff.

Cylinder Fins

Muffler

Air Screen

Blower

Housing

TILLER

TO ADJUST HANDLE HEIGHT (See Fig. 15)

Factory assembly has provided lowest handle height. Se lect

handle height best suited for your tilling conditions. Handle

height will be different when tiller digs into soil.

• If a higher handle height is desired, loosen the four

nuts securing handle panel to engine brackets.

• Slide handle panel to desired location.

• Tighten the four nuts securely.

HANDLE

PANEL

ENGINE BRACKETS

NUTS (ALSO 2

ON LEFT SIDE

OF TILLER)

Fig. 15

SERVICE AND ADJUSTMENTS

CAUTION: Disconnect spark plug wire from spark plug and place wire where it cannot come into

contact with plug.

Fig. 16

Fig. 17

TINE ARRANGEMENT

Your outer tines can be assembled in several different ways

to suit your tilling or cultivating needs.

CAUTION: Tines are sharp. Wear

gloves or other protection when han-

dling tines.

tine_4

OUTER

TINE

INNER TINE

HAIRPIN CLIP

CLEVIS

MID-WIDTH TILLING - 22" PATH (See Fig. 17)

• Assemble holes “A” in tine hubs to holes “C” in tine

shaft.

tine_5

NORMAL TILLING - 24" PATH (See Fig. 16)

• Assemble holes “A” in tine hubs to holes “B” in tine

shaft.

Fig. 18

NARROW TILLING/CULTIVATING - 12" PATH

(See Fig. 18)

• Remove outer tines.

tine_6

INNER TINES ONLY

NOTE: When reassembling outer tines, be sure right tine

assembly (marked “R”) and left tine assembly (marked “L”)

are mounted to correct side of tine shaft.

SERVICE AND ADJUSTMENTS

Fig. 19

ENGINE

TO AD JUST CARBURETOR

The carburetor has been preset at the factory and ad just ment

should not be necessary. However, engine per for mance

can be affected by dif fer enc es in fuel, tem per a ture, al ti tude

or load. If the carburetor does need ad just ment, contact

your nearest authorized service center/de part ment

IMPORTANT: NEVER TAMPER WITH THE ENGINE GOVERNOR,

WHICH IS FACTORY SET FOR PROPER ENGINE SPEED.

OVER SPEED ING THE ENGINE ABOVE THE FACTORY HIGH

SPEED SETTING CAN BE DANGEROUS. IF YOU THINK THE

ENGINE-GOVERNED HIGH SPEED NEEDS ADJUSTING,

CONTACT YOUR NEAREST AUTHORIZED SERVICE CENTER/

DEPARTMENT, WHICH HAS THE PROPER EQUIP MENT AND

EXPERIENCE TO MAKE ANY NEC ES SARY ADJUSTMENTS.

TO REMOVE BELT GUARD (See Fig. 20)

• Remove screws from side of belt guard.

• Pull belt guard out and away from unit.

• Replace belt guard by reversing above procedure. Be

sure slot in bottom of belt guard is under head of tine

shield bolt and all nuts are tightened securely.

Fig. 20

Screw

Belt Guard

TINE OPERATION CHECK (See Fig. 19)

WARNING: Disconnect spark plug wire

from spark plug to prevent starting while

checking tine operation.

For proper tine operation, tine control lever must be against

control body and all slack removed from inner wire of control

cable when control is in the “OFF” (up) position.

If lever and cable are loose, loosen cable clip at lower end of

cable. Pull up on cable to remove slack, without extending

spring on end of cable, and retighten cable clip.

FINAL CHECK “OFF” POSITION

• With tine control “OFF” (up), push down on handle to

raise tines off the ground.

• Slowly pull recoil starter handle while observing tines.

Tines should not rotate.

• If tines rotate, inner wire of control cable is too tight

which is extending lower spring and engaging tines.

Loosen cable clip and push down on cable only enough

to relieve spring tension. Tighten cable clip.

• Recheck in “OFF” position and adjust if necessary.

FINAL CHECK “ON” POSITION

• With tine control “ON” (held down to handle) push down

on handle to raise tines off the ground.

• Slowly pull recoil starter handle while observing tines.

Tines should rotate forward.

• If tines do not rotate, inner wire of control cable is too

loose. Loosen cable clip and pull cable up to remove

slack and retighten clip.

• Recheck in “ON” position and adjust if necessary.

NOTE: IF “ON” POSITION CHECK REQUIRED ADJUST-

MENT, RE CHECK “OFF” POSITION ADJUSTMENT TO

INSURE TINES DO NOT ROTATE WHEN CONTROL IS

“OFF” (UP).

TINE CONTROL

“ON” POSITION

TINE CONTROL

“OFF” POSITION

BODY

CABLE CLIP

TINE

CON TROL

CABLE

SERVICE AND ADJUSTMENTS

V-BELT

IDLER

PUL LEY

TRANS MIS SION

PUL LEY

BELT

GUIDE

ENGINE PULLEY

BELT

GUIDE

TO REPLACE V-BELT (See Fig. 21)

Replace V-belt if it has stretched considerably or if it has

cracks or frayed edges.

Belt guard must be removed to service belt. See “TO RE-

MOVE BELT GUARD” in this section of manual.

BELT REMOVAL

• Remove V-belt from transmission pulley first and then

from engine pulley.

BELT REPLACEMENT

Fig. 21

• Install new V-belt to engine pulley first then to trans mis-

sion pulley. Be sure belt is positioned on inside groove

of both pulleys, inside all belt guides and rests on idler

pulley.

CHECK TINE OPERATION

• See “TINE OPERATION CHECK” in this section of

manual.

REPLACE BELT GUARD

STORAGE

ENGINE OIL

Drain oil (with engine warm) and replace with clean oil. (See

“ENGINE” in the Maintenance section of this man ual).

CYLINDER(S)

• Remove spark plug.

• Pour 1 ounce (29 ml) of oil through spark plug hole into

cylinder.

• Pull starter handle slowly several times to distribute

oil.

• Replace with new spark plug.

OTHER

• Do not store gasoline from one season to another.

• Replace your gasoline can if your can starts to rust.

Rust and/or dirt in your gasoline will cause problems.

• If possible, store your unit indoors and cover it to give

protection from dust and dirt.

• Cover your unit with a suitable pro tec tive cover that

does not retain moisture. Do not use plastic. Plastic

cannot breathe which allows con den sa tion to form and

will cause your unit to rust.

IMPORTANT: NEVER COVER TILLER WHILE ENGINE AND

EXHAUST AREAS ARE STILL WARM.

Immediately prepare your tiller for storage at the end of the

season or if the unit will not be used for 30 days or more.

WARNING: Never store the tiller with

gasoline in the tank inside a build ing

where fumes may reach an open flame

or spark. Allow the engine to cool before

storing in any enclosure.

TILLER

• Clean entire tiller (See “CLEANING” in the Maintenance

section of this manual).

• Inspect and replace belts, if nec es sary (See belt re-

place ment in struc tions in the Service and Ad just ments

section of this manual).

• Lubricate as shown in the Maintenance section of this

manual.

• Be sure that all nuts, bolts and screws are securely

fastened. Inspect moving parts for damage, break age

and wear. Replace if necessary.

• Touch up all rusted or chipped paint surfaces; sand

lightly before painting.

ENGINE

FUEL SYSTEM

IMPORTANT: IT IS IMPORTANT TO PREVENT GUM DEPOSITS

FROM FORMING IN ESSENTIAL FUEL SYSTEM PARTS SUCH

AS THE CARBURETOR, FUEL FILTER, FUEL HOSE, OR TANK

DURING STORAGE. ALSO, EXPERIENCE INDICATES THAT

ALCOHOL BLENDED FUELS (CALLED GASOHOL OR USING

ETHANOL OR METHANOL) CAN ATTRACT MOISTURE WHICH

LEADS TO SEPARATION AND FORMATION OF ACIDS DURING

STORAGE. ACIDIC GAS CAN DAMAGE THE FUEL SYSTEM

OF AN ENGINE WHILE IN STORAGE.

• Empty the fuel tank by starting the engine and let it run

until the fuel lines and carburetor are empty.

• Never use engine or carburetor cleaner products in the

fuel tank or permanent.

• Use fresh fuel next season.

NOTE: Fuel stablizer is an acceptable alternative in

minimizing the formation of fuel gum deposits during

storage. Add stabilizer to gasoline in fuel tank or storage

container. Always follow the mix ratio found on stablizer

container. Run engine at least 10 minutes after adding

stablizer to allow the stabilizer to reach the carburetor.

Do not empty the gas tank and carburetor if using fuel

stabilizer.

Will not start

1 Out of fuel. 1 Fill fuel tank.

2 Fuel valve “OFF” 2 Turn fuel valve to the “ON” position.

3 Engine Switch “OFF” 3 Turn engine switch to the “ON” position.

4 Engine not “CHOKED” properly. 4 See “TO START ENGINE” in Operation section.

5 Engine flooded. 5 Wait several minutes before attempting to start.

6 Bad spark plug or improper gap. 6 Replace spark plug or adjust gap.

7 Dirty air filter. 7 Clean/replace air filter.

8 Water in fuel. 8 Empty fuel tank and carburetor, refill tank with fresh gasoline.

Hard to start

1 Throttle control not set properly. 1 See “To Start Engine” in Operations section.

2 Dirty air filter. 2 Clean/replace air filter.

3 Bad spark plug or improper gap. 3 Replace spark plug or adjust gap.

4 Stale or dirty fuel. 4 Empty fuel tank and refill tank with fresh, clean gasoline.

5 Loose spark plug wire. 5 Make sure spark plug wire is seated properly.

Loss of power

1 Engine is overloaded 1 Set depth stake and wheels for shallower tilling.

2 Dirty air cleaner 2 Clean/replace air filter.

3 Low oil level/dirty oil. 3 Check oil level/change oil.

4 Faulty spark plug. 4 Clean and regap or change spark plug.

5 Oil in fuel 5 Empty and clean fuel tank and refill, and clean carburetor.

6 Stale or dirty fuel. 6 Empty fuel tank and refill tank with fresh, clean gasoline.

7 Water in fuel. 7 Empty fuel tank and carburetor, refill tank with fresh gasoline.

8 Clogged fuel tank. 8 Remove fuel tank and clean.

9 Spark plug wire loose. 9 Connect and tighten spark plug wire.

10 Dirty engine air screen. 10 Clean engine air screen.

11 Dirty/clogged muffler. 11 Clean/replace muffler.

12 Poor Compression 12 Contact a Sears or other qualified service center.

Engine overheats

1 Low oil level/dirty oil. 1 Check oil level/change oil.

2 Dirty engine air screen. 2 Clean engine air screen.

3 Dirty engine. 3 Clean cylinder fins, airscreen, muffler area

4 Partially plugged muffler 4 Remove and clean muffler.

Excessive bounce/

difficult handling

1 Ground too dry and hard. 1 Moisten ground or wait for more favorable soil conditions

2 Wheels and depth stake incorrectly adjusted. 2 Adjust wheels and depth stake.

Soil balls up or clumps

1 Ground too wet. 1 Wait for more favorable conditions.

Engine runs but tiller

won’t move

1 Tine control is not engaged. 1 Engage tine control

2 V-belt not correctly adjusted. 2 Inspect/adjust V-belt.

3 V-belt is off pulley (s). 3 Inspect V-belt.

Engine runs but labors

when tilling

1 Tilling too deep. 1 Set depth stake for shallower tilling

2 Throttle control not properly adjusted. 2 Check throttle control setting.

TROUBLESHOOTING POINTS

SERVICE NOTES

LIMITED WARRANTY

The Manufacturer warrants to the original consumer purchaser that this product as manufactured is free from de-

fects in materials and work man ship. For a period of two (2) years from date of purchase by the original consumer

purchaser, we will repair or replace, at our option, without charge for parts or labor incurred in replacing parts, any

part which we find to be defective due to materials or workmanship. This Warranty is subject to the following limita-

tions and exclusions.

1. This warranty does not apply to the engine or components parts thereof. Please refer to the applicable manu-

facturer's warranty on these items.

2. Transportation charges for the movement of any power equipment unit or attachment are the responsibility of

the pur chaser. Transportation charges for any parts submitted for replacement under this warranty must be paid

by the purchaser unless such return is requested by the manufacturer.

3. The Warranty period for any products used for rental or commercial purposes is limited to 90 days from the date

of original purchase.

4. This Warranty applies only to products which have been properly assembled, adjusted, operated, and maintained

in ac cor dance with the instructions furnished. This Warranty does not apply to any product which has been

subjected to alteration, misuse, abuse, improper assembly or installation, delivery damage, or to normal wear

of the product.

5. Exclusions: Excluded from this Warranty are belts, tines, tine adapters, normal wear, normal adjustments, stan-

dard hard ware and normal maintenance.

6. In the event you have a claim under this Warranty, you must return the product to an authorized service deal-

er.

Should you have any unanswered questions concerning this Warranty, please contact:

giving the model number, serial number and date of purchase of your product and the name and address of the

authorized dealer from whom it was purchased.

THIS WARRANTY DOES NOT APPLY TO INCIDENTAL OR CONSEQUENTIAL DAMAGES AND ANY IMPLIED

WAR RAN TIES ARE LIMITED TO THE SAME TIME PERIODS STATED HEREIN FOR OUR EXPRESSED WAR-

RANTIES. Some areas do not allow the limitation of consequential damages or limitations of how long an implied

Warranty may last, so the above limitations or exclusions may not apply to you. This Warranty gives you specific legal

rights, and you may have other rights which vary from locale to locale.

This is a limited Warranty within the meaning of that term as defined in the Magnuson-Moss Act of 1975.

In Canada contact:

Poulan Pro

7075 Ordan Drive

Mississauga, Ontario

L5T 1K6

Poulan Pro

Customer Service Dept.

1030 Stevens Creek Road

Augusta, GA 30907 USA

This product has been expertly en gi neered and carefully manu fac tured to rigid quality stan dards. As with all

mechanical products, some adjustments or part replacement may be necessary during the life of your unit.

For Parts and service, contact our authorized distributor: call 1-800-849-1297

• For replacement parts, have available the following information:

a. Model Number/Manufacturer's I.D. Number

b. Description of part.

For Technical Assistance: call 1-800-829-5886

For a Parts Manual, go to our website: www.poulan-pro.com/support.asp

NOTE: HOP provides parts and service through its au thor ized dis tribu tors and dealers; there fore,

all requests for parts and service should be directed to your local dealer(s). The phi loso phy

of HOP is to con tinu ally improve all of its prod ucts. If the operating characteristics or the

appearance of your product differs from those described in this Manual, please contact your

local dealer for updated in for ma tion and as sis tance.

PARTS AND SERVICE

La page charge ...

Poulan Pro HDF900 Le manuel du propriétaire

Marque: Poulan Pro

Modèle: HDF900

Catégorie: Mini motoculteurs

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: Poulan Pro HDF900 Owner's manual

Poulan Pro HDF900 Le manuel du propriétaire

Poulan Pro HDF900 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents