Sharp KC-860U Manuel utilisateur

ENGLISH

FRANÇAISESPAÑOL

AIR PURIFIER

with Humidifying Function

OPERATION MANUAL

PURIFICADOR DE AIRE

Con función de humidicación

MANUAL DE OPERACIÓN

Puricateur d’air à fonction

d’humidication

MANUEL D’UTILISATION

Device of this mark is a trademark of Sharp Corporation.

“Plasmacluster” and “Device of a cluster of grapes” are

registered trademarks of Sharp Corporation in Japan,

USA and elsewhere.

This product earned the ENERGY STAR by meeting

strict energy efficiency guidelines set by the US EPA.

US EPA does not endorse any manufacturer claims of

healthier indoor air from the use of this product.

The energy efficiency of this ENERGY STAR qualified

model is measured based on a ratio between the model’

s CADR for Dust and the electrical energy it consumes,

or CADR/Watt.

Ce produit a le droit de porter la marque ENERGY

STAR après avoir répondu à des critères stricts en ce

qui concerne l’efcacité énergétique, tels qu’établis par

l’agence EPA aux É-U. L’agence EPA aux É-U n’appuie

aucunement les témoignages publicitaires du fabricant

indiquant que ce produit rend l’air intérieur des locaux

plus sain.

L’efcacité énergétique de ce modèle, qui bénécie de

la reconnaissance ENERGY STAR, est mesurée par le

rapport entre le DAP (débit d’air purié) du modèle et l’

énergie électrique qu’il consomme, soit le rapport DAP/

Watt.

KC-850U

KC-850U_Eng.indd 1 10.4.14 10:34:53 AM

Please read before operating your new Air Purier

True HEPA lter (white)

Washable Deodorizing lter (black)

Pre-lter

The air purier draws in room air from the air intake, passes the air through a Pre-

Filter, a Washable Deodorizing lter and a True HEPA lter inside of the unit, then dis-

charges the air through the air outlet. The True HEPA lter can remove 99.97% of dust

particles as small as 0.3 microns that pass through the lter and also helps absorb

odors. The Washable Deodorizing lter gradually absorbs odors as they pass through

the lter.

Some odors absorbed by the lters may break down over time, resulting in additional

odor. Depending on the usage environment, especially when the product is used in ex-

treme environments (signicantly more severe than normal household use), this odor

may become strong in a shorter period than expected. If the odor persists, the lters

should be replaced.

NOTE

• The air purifier is designed to remove air-suspended dust and odor, but not harmful gases (for

example, carbon monoxide contained in cigarette smoke). If the source of the odor still exists, the

air purier may not completely remove the odor.

KC-850U_Eng.indd 2 10.4.14 10:34:53 AM

ENGLISH

E-1

FEATURES

ENGLISH

Declaration of Conformity

SHARP AIR PURIFIER KC-850U

This ISM device complies with Canadian

ICES-001

Responsible Party:

SHARP ELECTRONICS OF CANADA LTD.

335 Britannia Road East Mississauga, Ontario

L4Z 1W9 Canada

TEL: (905) 568-7140

Thank you for purchasing this SHARP Air Pu-

rier. Please read this manual carefully be-

fore using the air purier.

After reading, keep the manual in a conven-

ient location for future reference.

Declaration of Conformity

SHARP AIR PURIFIER KC-850U

This device complies with Part 18 of FCC rules.

Responsible Party:

SHARP ELECTRONICS CORPORATION

Sharp Plaza,

Mahwah, New Jersey 07495-1163

CONTENTS

FOR CUSTOMER ASSISTANCE(U.S)

......

E-2

CONSUMER LIMITED WARRANTY(U.S)

.....

E-3

FOR CUSTOMER ASSISTANCE(CANADA)

....

E-4

LIMITED WARRANTY(CANADA)

...........

E-5

IMPORTANT SAFETY INSTRUCTIONS

...

E-6

• WARNING ..................................................

E-6

• CAUTIONS CONCERNING OPERATION .

E-7

• INSTALLATION GUIDELINES ....................

E-7

• FILTER GUIDELINES ................................

E-7

PART NAMES

.............................................

E-8

• ILLUSTRATIVE DIAGRAM .........................

E-8

• BACK ..........................................................

E-8

• MAIN UNIT DISPLAY .................................

E-9

• FRONT MONITOR .....................................

E-9

PREPARATION FOR USE ..........................

E-10

• FILTER INSTALLATION ...........................

E-10

• REFILLING WATER TANK .......................

E-11

OPERATION

.............................................

E-12

• CLEAN AIR & HUMIDIFY MODE .............

E-12

• CLEAN AIR MODE ...................................

E-12

• QUICK CLEAN MODE .............................

E-13

• FAN SPEED BUTTON ..............................

E-13

• Plasmacluster ON/OFF BUTTON .............

E-13

• POWER ON/OFF BUTTON ......................

E-13

• LIGHTS CONTROL BUTTON ..................

E-14

• WATER SUPPLY INDICATOR LIGHT ......

E-14

•

ADJUSTMENT OF SENSOR DETECTION SENSITIVITY

..

E-14

CARE AND MAINTENANCE

.................

E-15

• FILTER INDICATOR LIGHT .....................

E-15

• BACK PANEL AND SENSORS ................

E-15

• MAIN UNIT ..............................................

E-15

• WATER TANK ...........................................

E-16

• WASHABLE DEODORIZING

FILTER .....................................................

E-16

• HUMIDIFYING TRAY ...............................

E-17

• HUMIDIFYING FILTER .............................

E-18

•

FILTER REPLACEMENT GUIDELINES

.....

E-19

TROUBLESHOOTING

............................

E-20

SPECIFICATIONS

....................................

E-22

Unique Combination of Air Treatment

Technologies

Triple Filtration System + Plasmacluster

+ Humidication

TRAPS DUST*

Washable pre-filter traps dust and other

large airborne particles.

DECREASES ODORS

Washable deodorizing lter absorbs many

common household odors.

REDUCES POLLEN & MOLD*

True HEPA lter traps 99.97% of particles

as small as 0.3 microns.

FRESHENS

Plasmacluster refreshes the air similar to

the way nature cleans the environment by

emitting a balance of positive and negative

ions.

HUMIDIFIES

Runs up to 10 hours per lling.**

*When air is drawn through the filter sys-

tem.

**Room size : up to 254 sq. ft.

Sensor Technology continuously monitors

air quality, automatically adjusting opera-

tion based on detected air purity and hu-

midity.

KC-850U_Eng.indd 1 10.4.14 10:34:53 AM

E-2

FOR CUSTOMER ASSISTANCE

(the United States)

MODEL NUMBER

SERIAL NUMBER

DATE OF PURCHASE

Dealer Name

Address

City

State

Zip

Telephone

TO PHONE: Dial 1-800-BE-SHARP (237-4277) for:

SERVICE (for your nearest Sharp Authorized Servicer)

PARTS (for your Authorized Parts Distributor)

ACCESSORIES

ADDITIONAL CUSTOMER INFORMATION

TO WRITE: For service problems, warranty information, missing items and other assistance:

Sharp Electronics Corporation

Customer Assistance Center

1300 Naperville Drive

Romeoville, IL 60446-1091

TO ACCESS OUR WEB SITE: www.sharpusa.com

Please provide the following information when you write or call: model number, serial

number, date of purchase, your complete mailing address (including zip code), your daytime

telephone number (including area code) and description of the problem.

To aid in answering questions if you call for service or for reporting loss or theft, please use

the space below to record the model and serial number located on the back of the unit.

KC-850U_Eng.indd 2 10.4.14 10:34:53 AM

ENGLISH

E-3

FOR CUSTOMER ASSISTANCE

(the United States)

CONSUMER LIMITED WARRANTY FOR U.S. USERS

SHARP ELECTRONICS CORPORATION warrants to the rst consumer purchaser that this Sharp brand product (the

“Product”), when shipped in its original container, will be free from defective workmanship and materials, and agrees

that it will, at its option, either repair the defect or replace the defective Product or part thereof with a new or remanufac-

tured equivalent at no charge to the purchaser for parts or labor for the period(s) set forth below.

This warranty does not apply to any appearance items of the Product nor to the additional excluded item(s) set forth

below nor to any Product the exterior of which has been damaged or defaced, which has been subjected to improper

voltage or other misuse, abnormal service or handling, or which has been altered or modied in design or construction.

In order to enforce the rights under this limited warranty, the purchaser should follow the steps set forth below and pro-

vide proof of purchase to the servicer.

The limited warranty described herein is in addition to whatever implied warranties may be granted to purchasers by

law. ALL IMPLIED WARRANTIES INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR USE

ARE LIMITED TO THE PERIOD(S) FROM THE DATE OF PURCHASE SET FORTH BELOW. Some states do not

allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.

Neither the sales personnel of the seller nor any other person is authorized to make any warranties other than those de-

scribed herein, or to extend the duration of any warranties beyond the time period described herein on behalf of Sharp.

The warranties described herein shall be the sole and exclusive warranties granted by Sharp and shall be the sole and

exclusive remedy available to the purchaser. Correction of defects, in the manner and for the period of time described

herein, shall constitute complete fulllment of all liabilities and responsibilities of Sharp to the purchaser with respect

to the Product, and shall constitute full satisfaction of all claims, whether based on contract, negligence, strict

liability or otherwise. In no event shall Sharp be liable, or in any way responsible, for any damages or defects in the

Product which were caused by repairs or attempted repairs performed by anyone other than an authorized servicer. Nor

shall Sharp be liable or in any way responsible for any incidental or consequential economic or property damage. Some

states do not allow the exclusion of incidental or consequential damages, so the above exclusion may not apply to you.

THIS WARRANTY GIVES YOU SPECIFlC LEGAL RIGHTS. YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY

FROM STATE TO STATE.

Your Product Model Number & Description:

Warranty Period for this Product:

Additional Item(s) Excluded From Warranty

Coverage:

Where to Obtain Service:

What to Do to Obtain Service:

TO OBTAIN SUPPLY, ACCESSORY OR PRODUCT INFORMATION, CALL 1-800-BE-SHARP, OR VISIT OUR WEBSITE AT

www.sharpusa.com

SHARP ELECTRONICS CORPORATION

Sharp Plaza, Mahwah, New Jersey 07495-1163

CONSUMER LIMITED WARRANTY

KC-850U Air Purier. Be sure to have this information available when

you need service for your Product.

One (1) year parts and labor from date of purchase.

Appearance items of the Product, lters, accessories, or any printed

materials. Product which has been used for rental and/or commercial

purposes.

From a Sharp Authorized Servicer located in the United States. To

nd the location of the nearest Sharp Authorized Servicer, call Sharp

Toll Free at 1-800-BE-SHARP.

Ship prepaid or carry in your Product to a Sharp Authorized Servicer.

Be sure to have Proof of Purchase available. If you ship the Product,

be sure it is insured and packaged securely.

KC-850U_Eng.indd 3 10.4.14 10:34:54 AM

E-4

FOR CUSTOMER ASSISTANCE

(Canada)

To aid in answering questions if you call for service or for reporting loss or theft, please use

the space below to record the model and serial number located on the back side of the unit.

MODEL NUMBER

SERIAL NUMBER

DATE OF PURCHASE

Dealer Name

Address

City

Province

Postal Code

Telephone

TO PHONE: Dial 1-905-568-7140 for:

SERVICE (for your nearest Sharp Authorized Servicer)

PARTS (for your Authorized Parts Distributor)

ACCESSORIES

ADDITIONAL CUSTOMER INFORMATION

TO WRITE: For service problems, warranty information, missing items and

other assistance:

Sharp Electronics of Canada Ltd.

Customer Care

335 Britannia Road East

Mississauga, Ontario L4Z 1W9

TO ACCESS OUR WEB SITE: www.sharp.ca

Please provide the following information when you write or call: model number, serial number,

date of purchase, your complete mailing address (including Postal Code), your daytime tel-

ephone number (including area code) and description of the problem.

KC-850U_Eng.indd 4 10.4.14 10:34:54 AM

ENGLISH

E-5

LIMITED WARRANTY

Consumer Electronics Products

Congratulations on your purchase!

Sharp Electronics of Canada Ltd. (hereinafter called “Sharp”) gives the following express warranty to the first consumer purchaser for this

Sharp brand product, when shipped in its original container and sold or distributed in Canada by Sharp or by an Authorized Sharp Dealer:

Sharp warrants that this product is free, under normal use and maintenance, from any defects in material and workmanship. If any such

defects should be found in this product within the applicable warranty period, Sharp shall, at its option, repair or replace the product as

specified herein.

This warranty shall not apply to:

(a) Any defects caused or repairs required as a result of abusive operation, negligence, accident, improper installation or inappropriate

use as outlined in the owner’s manual.

(b) Any Sharp product tampered with, modified, adjusted or repaired by any party other than Sharp, Sharp’s Authorized Service Centres

or Sharp’s Authorized Servicing Dealers.

(c) Damage caused or repairs required as a result of the use with items not specified or approved by Sharp, including but not limited to

head cleaning tapes and chemical cleaning agents.

(d) Any replacement of accessories, glassware, consumable or peripheral items required through normal use of the product including but

not limited to earphones, remote controls, AC adapters, batteries, temperature probe, stylus, trays, filters, belts, ribbons, cables and

paper.

(e) Any cosmetic damage to the surface or exterior that has been defaced or caused by normal wear and tear.

(f) Any damage caused by external or environmental conditions, including but not limited to transmission line/power line voltage or liquid

spillage.

(g) Any

product received without appropriate model, serial number and CSA/cUL markings.

(h) Any products used for rental or commercial purposes.

(i) Any installation, setup and/or programming charges.

Should this Sharp product fail to operate during the warranty period, warranty service may be obtained upon delivery of the Sharp product

together with proof of purchase and a copy of this LIMITED WARRANTY statement to an Authorized Sharp Service Centre or an

A

uthorized Sharp Servicing Dealer. In home warranty service may be provided at Sharp’s discretion on any Sharp television with the

screen size of 27” or larger and on any Sharp Over-the-Range Microwave Oven.

This warranty constitutes the entire express warranty granted by Sharp and no other dealer, service centre or their agent or employee is

authorized to extend, enlarge or transfer this warranty on behalf of Sharp. To the extent the law permits, Sharp disclaims any and all

liability for direct or indirect damages or losses or for any incidental, special or consequential damages or loss of profits resulting from a

defect in material or workmanship relating to the product, including damages for the loss of time or use of this Sharp product or the loss o

f

information. The purchaser will be responsible for any removal, reinstallation, transportation and insurance costs incurred. Correction o

f

defects, in the manner and period of time described herein, constitute complete fulfillment of all obligations and responsibilities of Sharp to

the purchaser with respect to the product and shall constitute full satisfaction of all claims, whether based on contract, negligence, strict

liability or otherwise.

WARRANTY PERIODS: Parts & Labour (exceptions noted)

Audio Product 1 year

redrocmaC 1 year

DVD Product 1 year

Projector 1 year (lamp 90 days)

LCD TV 1 year

Microwave Oven 1 year (magnetron component-4 additional years)

Air Purifier 1 year

Portable Air Conditioner 1 year

Plasmacluster Ion Generator 1 year

To obtain the name and address of the nearest Authorized Sharp Service Centre or Dealer, please contact:

SHARP ELECTRONICS OF CANADA LTD. 335 Britannia Road East Mississauga, Ontario L4Z 1W9

For more information on this Warranty, Sharp Extended Warranty

Offers, Sharp Canada Products, Accessory Sales, Dealer or Service

Locations, please call (905) 568-7140

Visit our Web site: www.sharp.ca

T

O

B

E

T

H

E

B

E

S

T

H

R

O

U

G

H

C

U

S

T

O

M

E

R

S

A

T

I

S

F

A

C

T

I

O

N

SERVICE

KC-850U_Eng.indd 5 10.4.14 10:34:54 AM

E-6

IMPORTANT SAFETY INSTRUCTIONS

When using electrical appliances, basic safety precautions should be followed, including the

following:

WARNING

- To reduce the risk of electrical shock, re or injury to persons:

• Read all instructions before using the unit.

• Use only a 120 volt outlet.

• The air purier has a polarized plug (one blade is wider than the other). This plug will t in a polar

-

ized outlet only one way. If the plug does not t into the outlet, reverse it. If it still does not t, con-

tact a qualied electrician or service person.

• Do not use the unit if the power cord or plug is damaged or the connection to the wall outlet

is loosened.

• Periodically remove dust from the plug.

• Do not insert ngers or foreign objects into the air intake or air outlet.

• When removing the power plug, always hold the plug and never pull on the cord.

Electrical shock and/or re from a short circuit may occur as a result.

• Do not remove the plug when your hands are wet.

• Do not use this unit near gas appliances or replaces.

•

When relling the Water Tank, cleaning the unit, or when the unit is not in use, be sure to unplug

the unit. Electrical shock and/or re from a short circuit may occur as a result.

• If the power cord is damaged, it must be replaced by the manufacturer, its service agent, a

Sharp Authorized Service Center or similarly qualied person in order to avoid a hazard.

• Do not operate when using aerosol insecticides or in rooms where there is oily residue, incense,

sparks from lit cigarettes, chemical fumes in the air, or in locations where the unit may get wet,

such as a bathroom.

• Be cautious when cleaning the unit. Strong corrosive cleansers may damage the exterior.

• Only a Sharp Authorized Service Center should service this air purier. Contact the nearest Service

Center for any problems, adjustments, or repairs.

• When carrying the unit, remove the Water Tank and Humidifying Tray rst and hold the unit by han-

dles on both sides.

• Do not drink the water in the Humidifying Tray or Water Tank.

• Change the water in the Water Tank daily with fresh tap water and regularly clean the Water Tank

and Humidifying Tray. (See E-16 and E-17). When unit is not in use, dispose of the water in the

Water Tank and Humidifying Tray. Leaving water in the Water Tank and/or Humidifying Tray may

result in mold, bacteria, and bad odors.

In rare cases, this bacteria may cause harmful physical effects.

NOTE

- Radio or TV Interference

If this air purier should cause interference to radio or television reception, try to correct the interfer-

ence by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation distance between the unit and radio/TV receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is con-

nected.

• Consult the dealer or an experienced radio/TV technician for help.

This product fulls the requirement of the International standard CISPR 11.

In conformity with this standard, this product is classied as group 2 class B equipment.

Group 2 means that the equipment intentionally generates radio-frequency in the form of electromag-

netic radiation for electro-discharge machining equipment.

Class B equipment means that the equipment suitable to be used in domestic establishments.

KC-850U_Eng.indd 6 10.4.14 10:34:55 AM

ENGLISH

E-7

CAUTIONS CONCERNING OPERATION

• Do not block the intake and/or air outlet.

• Do not use the unit near or on hot objects, such as stoves or heaters or where it may come into

contact with steam.

• Always operate the unit in an upright position.

• Always hold the handles on both sides of the unit when moving it.

Holding the back panel when carrying may cause it to detach, thus dropping the unit and resulting

in bodily injury.

• Do not operate the unit without the lters, Water Tank, and Humidifying Tray properly in-

stalled.

• Do not wash and reuse the True HEPA lter.

Washing will not improve lter performance, it may cause electric shock or malfunction.

• Clean the exterior with a soft cloth only.

Do not use volatile uids and/or detergents.

The unit surface may be damaged or cracked.

In addition, the sensors may malfunction as a result.

• Frequency of maintenance required (descaling) will depend on the hardness or the impuri

-

ties of the water that you use; the harder the water the more often descaling will be neces-

sary.

• Keep the unit away from water.

INSTALLATION GUIDELINES

• During the operation of the product, please place the unit at least 6.5ft. (2m) away from

equipment utilizing electrical waves such as televisions, radios or wave clocks.

• Avoid a location where the sensor is exposed to direct breeze or draft.

The unit may not operate properly.

• Avoid use in locations where furniture, fabrics or other items may come in contact with and

restrict the air intake and/or air outlet.

• Avoid use in locations where the unit is exposed to condensation or rapid temperature

changes. (Use under appropriate conditions between 41 - 95˚F (5 - 35˚C) in the room.)

(If it is unavoidable please allow unit to stand for 1 hour before switching on.)

• Place on a stable surface with sufcient air circulation.

When placing the unit on a heavily carpeted area, the unit may vibrate slightly.

Place the unit on an even surface to avoid water leakage from the Water Tank and/or Humidifying

Tray.

• Avoid use in locations where grease or oily smoke is generated.

(such as in a kitchen, etc.).

The unit surface may crack or the sensor may malfunction as a result.

• Place the unit about 1-2 ft. (30 - 60cm) away from the wall in order to ensure proper airow.

The wall directly behind the air outlet may become dirty over time. When using the unit for an

extended period of time in the same location, periodically clean the wall and protect the wall with a

vinyl sheet, etc. to prevent the wall from becoming dirty.

FILTER GUIDELINES

• Follow the instructions in this manual for correct care and maintenance of the lters.

Use only lters designed for this product.

KC-850U_Eng.indd 7 10.4.14 10:34:55 AM

E-8

PART NAMES

ILLUSTRATIVE DIAGRAM - FRONT

BACK

Air Outlet

True HEPA lter (white)

Washable Deodorizing

lter (black)

Tabs

Back Panel (Pre-lter)

Air Inlet

Date Label

(Rating Label)

Front Monitor

Air Outlet

Main Unit

Main Unit Display

Handle(2 locations left and right)

Sensors

• Dust Sensor

•

Temperature / Humidity Sensor

Tank Handle

Water Tank

(For humidifying)

Humidifying Filter

Filter Frame

Tank Cap

Float

Humidifying Tray

Power Cord

Plug

KC-850U_Eng.indd 8 10.4.14 10:34:55 AM

ENGLISH

E-9

FRONT MONITOR

Filter Reset Button/

Indicator Light (red)

Plasmacluster ON/OFF Button/

Indicator Light (green)

Power OFF Button

Power ON Button

Light Control Button

Fan Speed Button/

Indicator Light (green)

Quick Clean MODE Button/

Indicator Light (blue)

Press any of the buttons to select

mode and start the unit.

Clean Air & Humidify MODE Button/

Indicator Light (green)

Clean Air MODE Button/

Indicator Light (green)

MAIN UNIT DISPLAY

Water Supply Indicator Light (red)

This light will illuminate when the water

tank needs to be re lled.

Sensor Reading

Flashing

Clean

All green

Green

Yellow

Very lmpure

All red

Clean

All green

Green

Yellow

Very lmpure

All red

Flashing

Indicates condition and humidity of room air.

Plasmacluster Indicator Light (blue)

Blue: Plasmacluster ON

Light off: Plasmacluster OFF

Humidity Indicator Light (green)

Displays the approximate humidity level

in the room. Humidity setting is pre-set

for maximum comfort.

DUST MONITOR

The dust sensor continuously monitors

the air and changes color depending on

air purity.

When the dust sensor detects dust, the

 ashing light moves depending on the

amount of dust detected.

(Ex.) At 60 % humidily

80 % or more

Less than 30 %

KC-850U_Eng.indd 9 10.4.14 10:35:07 AM

E-10

FILTER INSTALLATION

Date Label

Unplug the unit before installing

or adjusting the lters.

PREPARATION FOR

USE

1

Remove the Back Panel.

Gently push down on the tabs,

then tilt and remove the back

panel.

Install the lters

To maintain the quality of the lters, they are packed in plastic bags and placed in

the unit. Be sure to remove the lters from the plastic bags and replace the lters in

the unit before initial use.

Remove the lters

2

Remove the Washable

Deodorizing lter (black)

and True HEPA lter

(white) from the plastic

bags.

Back Panel

True HEPA filter

(white)

Washable

Deodorizing

lter (black)

True HEPA lter

2

Insert the Back Panel’s 2 bottom tabs

(left and right) into the small holes in the

unit, and slide the Washable Deodorizing

lter between the True HEPA lter and

the Back Panel.

3

Gently push in the

upper tabs (left

and right) to lock

in place.

1

2

Tabs on the top

Washable Deodorizing lter

Back Panel

Bottom tabs

Upper tabs

1

I

nstall the True HEPA lter.

Please make sure that the True HEPA

lter is placed in proper orientation.

Installing the lter backwards

will affect the performance of

the unit.

4

Fill in the usage

start date and

place on the unit as

guide for when the

lters should be

replaced.

KC-850U_Eng.indd 10 10.4.14 10:35:08 AM

ENGLISH

E-11

REFILLING THE WATER TANK

The unit can be used in the Clean Air Mode without

putting water in the Water Tank. When using the

Clean Air & Humidify Mode, or the Quick Clean Mode,

the Water Tank should be lled with water.

1

Remove the Water Tank by unlatching the

top.

2

Remove the Water Tank Cap and carefully

ll the Water Tank with tap water.

• Change the water in the Water Tank every day with

fresh tap water.

3

After lling, securely tighten the Tank Cap.

• Check to see that there is no water leaking.

• Be sure to wipe off any excess water on the outside

of the Water Tank.

• When carrying the Water Tank, hold it with both

hands so that the Water Tank opening is facing up.

4

Replace the Water Tank in the unit.

• The top latch will “click” in place when the Water

Tank is properly installed.

CAUTION

Tank Handle

Water Tank

Humidifying

Tray

tighten

• Do not expose the unit to water. Short circuit and/or electrical shock may occur as a result.

• Do not use hot water (104ºF or 40ºC), chemical agents, aromatic substances, dirty water,

or other damaging substances, deformation and/or malfunction may occur.

• Use only fresh tap water. Use of other water sources may promote the growth of mold, fun-

gus and/or bacteria.

Tank Cap

KC-850U_Eng.indd 11 10.4.14 10:35:08 AM

E-12

CLEAN AIR & HUMIDIFY MODE

OPERATION

Use the Clean Air & Humidify Mode to quickly clean the air, reduce odors and to humidify.

1

Fill Water Tank. (See E-11)

Use the Clean Air Mode when additional humidity is not required.

About Automatic Humidify Mode

3

Press the FAN SPEED Button to select the

desired fan speed. (See E-13)

2

Press the CLEAN AIR & HUMIDIFY MODE

Button.

• If the power cord was not unplugged between uses, the

unit will automatically re-start at the previously selected

settings.

The Temperature/Humidity sensors automatically de-

tect and adjust humidity according to changes in room

temperature. Depending on the size and humidity of

the room, humidity may not reach 45 - 55 %. In such

cases, it is recommended that CLEAN AIR & HUMIDI-

FY/MAX MODE be used.

CLEAN AIR MODE

1

Press the CLEAN AIR MODE Button on the display

.

• If the power cord was not unplugged between uses, the

unit will automatically re-start at the previously selected

settings.

2

Press the FAN SPEED BUTTON to select the

desired fan speed. (See E-13)

Temperature Humidity

64 and below 55%

64-75 50%

75 and above 45%

Plasmacluster

ON/OFF Button

Power OFF

Button

Fan Speed

Button

Quick Clean MODE Button

Clean Air & Humidify MODE Button

Clean Air MODE Button

KC-850U_Eng.indd 12 10.4.14 10:35:08 AM

ENGLISH

E-13

QUICK CLEAN MODE

1

Press the QUICK CLEAN MODE Button on

the display to select this mode.

When the operation nishes, the unit will return to the

prior operation.

FAN SPEED Button

AUTO operation

The fan speed is automatically switched (HIGH*, MEDIUM, LOW) depending on

the amount of impurities in the air. The sensors detect the impurities for efcient air

purication.

MAX operation

MEDIUM operation

LOW operation

The unit will operate at maximun fan speed .

The unit will operate at medium fan speed .

The unit will operate quietly using minimal air intake.

* HIGH fan speed is an intermediate speed between MEDIUM and MAX.

Plasmacluster ON/OFF Button

Press the Plasmacluster ON/OFF Button to turn Plasmaclus-

ter Ion Mode ON and OFF. When Plasmacluster is ON, both

the Indicator Light and Plasmacluster Indicator Light on the

front display turn on.

POWER OFF Button

Press the Power OFF Button to turn the unit off.

Press the FAN SPEED Button to select the preferred fan settings.

Indicator lights will show the speed currently selected. Please note

the fan speed cannot be adjusted during the QUICK CLEAN Mode.

QUICK CLEAN Mode with humidication releases high-density Plasmacluster ions. By con-

tinuously discharging strong airow cycles, the unit effectively removes airborne dust, pollen,

mold and allergens from the air as they are drawn through the lter system. Water must be in

the Water Tank when this mode is selected.

The unit humidies when there’s water in the Water Tank, and it operates without humidifying

when there is no water in it.

POLLEN

mode operation

The unit will operate at High level for 10 minutes, then will

alternated between MED and HIGH every 20 minutes.

KC-850U_Eng.indd 13 10.4.14 10:35:09 AM

E-14

OPERATION

WATER SUPPLY INDICATOR LIGHT

When the Water Tank is empty, the Water Supply Indicator Light will  ash

to indicate that the Water Tank should be refilled. Please note the light

will not  ash even when the Water Tank is empty during the Clean Air

Mode and the Quick Clean Mode.

Sound indicator setting for water supply.

In addition to the Indicator Light, the unit can be set to signal

with an audible beep when the Water Tank is empty. With the

unit OFF, press the Lights Control button for 3 seconds to turn

the audible signal ON.

Cancellation

To cancel the audible signal, with the unit OFF, press the Lights

Control button again more than 3 seconds.

ADJUSTMENT OF SENSOR DETECTION SENSITIVITY

Set to ‘low” if the DUST MONITOR is constantly red to reduce sensitivity, and set to

‘high’ if the DUST MONITOR is constantly green to increase sensitivity.

1

With the unit OFF, press the Fan Speed Button for 3 seconds.

The Fan Speed Indicator Lights will display the currently set sensor sensitivity level. The

factory setting is Standard, indicated by the MED light.

2

Press the Fan Speed Button to set

the desired sensor sensitivity.

Refer to the diagram on the right to select the

desired sensor sensitivity level.

3

Press the Power OFF Button.

Note that if the Power OFF Button is not pushed

within 8 seconds of adjusting sensor sensitivity,

the setting will be saved automatically. The sen-

sor sensitivity setting will be saved even if the

unit is unplugged.

Sensor Detection

sensitivity

Fan Speed

Indicator Light

High

Standard

Low

Use when the light on the

front panel is too bright.

Refer to the diagram to select the desired

brightness on the front panel.

CAUTION

The lights on the front monitor are always brighter when starting.

The lights on the front panel are brighter.

The lights on the front panel are darker.

The lights on the front monitor turn off.

LIGHTS CONTROL Button

KC-850U_Eng.indd 14 10.4.14 10:35:10 AM

ENGLISH

E-15

CARE AND MAINTENANCE

UNIT

To prevent dirt or stains on the unit, clean regularly. If stains are allowed to remain, they may

become difcult to remove.

Wipe with a dry, soft cloth

For stubborn stains or dirt, use a soft cloth dampened with warm water.

Do not use volatile uids

Benzene, paint thinner, polishing powder, may damage the surface.

Do not use detergents

Detergent ingredients may damage the unit.

FILTER INDICATOR LIGHT

The Filter Indicator Light will illuminate as a reminder to perform mainte-

nance of the Back Panel, Sensors, and Humidifying lter. The Indicator

Light will turn on after approximately 720 hours of use.

After performing maintenance, reset the Filter Indicator. Plug the unit in,

turn power ON, and press the RESET button for 3 seconds. The Filter

Indicator Light will go off. Even if the Filter Indicator Light is already off,

the RESET button should be pressed to reset the maintenance timer.

To maintain optimum performance of this air purier, please clean the unit including

the sensor opening and lters periodically.

When cleaning the unit, be sure to rst unplug the power cord, and never handle the

plug with wet hands. Electrical shock and/or bodily injury may occur as a result.

After 720 hours of use

(30days ×24hours = 720)

Whenever dust accumulates on the unit or every 2 months

Care Cycle

Sensor

Back Panel

Care Cycle

Whenever dust accumulates

on the unit or every 2 months

Gently remove dust from the sensor opening and the

back panel, using a vacuum cleaner attachment or

similar tool.

When the back panel has stubborn dirt

1

In case of oily dirt, soak the back panel in water with

kitchen detergent.

Avoid scrubbing the back panel when washing.

2

Rinse the back panel repeatedly with clean water to re-

move the solution residue.

3

Drip dry panel to remove excess water.

SENSOR FILTER CARE

Remove the sensor filter and tap it lightly over a sink

or bin to dislodge dust. If it is very dirty, wash it gently

with lukewarm water. Do not use any detergents or

chemicals of any kind to clean the lter. Dry the lter

completely before replacing in the unit. Do not operate

unit without all lters properly installed.

BACK PANEL and SENSORS

Sensor lter

KC-850U_Eng.indd 15 10.4.14 10:35:10 AM

E-16

WASHABLE DEODORIZING FILTER CARE

2

Drip dry lter to remove excess water.

HAND WASH ONLY!

DO NOT DRY IN CLOTHES

DRYER!

• Avoid drying lter outdoors during inclement weather (e.g. rain or cold temperatures).

Do not allow lter to freeze.

• If lter is dried indoors, take precautions, such as placing towels, etc under the lter to

prevent water damage to the oor.

1

Rinse dirt from the WASHABLE DEODORIZING

FILTER under lukewarm water.

3

Dry lter completely in a well ventilated area.

If possible, dry outdoors.

Dry lter in a sideways position to avoid warping of the lter.

The lter takes about 6 hours to dry completely.

CAUTION

CARE AND MAINTENANCE

CAUTION

• When washing the lter for the rst time, the rinse water may

be brown. This does not affect deodorization performance.

• Avoid bending or folding the lter when washing.

When an unpleasant odor is noticed from

the air outlet.

When performance of lter seems to be

reduced and odors persist.

Care Cycle

WATER TANK

Rinse the inside of the tank by leaving a small amount of luke-

warm water inside, closing the tank cap firmly, and shaking

the tank. Mild household detergents may be used to clean the

inside of the tank, but detergent should be diluted and the tank

should be thoroughly rinsed to remove all detergent residue.

(Note the Water Tank is not dishwasher safe.)

TANK CAP CARE

The small cap back of the tank cap is removable.

When the tank cap and small cap are dirty and/or

slimy, cleaning is necessary.

Use a cotton swab or a toothbrush.

Tank Cap

Water Tank

Tank Cap

Toothbrush

Care Cycle

Every day when Humidifying

4

Replace the lter in unit. (See E-10).

Dry lter completely before replacing to prevent odors.

Do not operate unit without all lters properly installed.

KC-850U_Eng.indd 16 10.4.14 10:35:11 AM

ENGLISH

E-17

Frequency of maintenance cycle will depend on the hardness

of the water. Avoid spilling water when removing or cleaning

the tray.

1

Remove the Water Tank and Humidifying Tray.

Unlatch the Water

Tank rst, then re-

move the tray. Use

both hands when

pulling out the

Humidifying Tray to

avoid spilling water.

3

Rinse the inside of the Humidifying

Tray with lukewarm water to remove

impurities.

• Do not remove the

Styrofoam oat .

• Clean difcult-to-

reach parts with a

cotton-tipped swab

or tooth brush.

CAUTION

Water Tank

Tank Handle

Humidifying

Tray

Float

If the Styrofoam oat comes off,

replace by inserting the tabs of

the Float into the holes in the

Humidifying Tray as shown in the

diagram.

When Water Deposits are Difcult to Remove

• Use only mild kitchen detergents to

clean the Humidifying Tray. Use of

non-designated chemicals or deter-

gents can cause deformation, tarnish-

ing, cracking (water leakage).

Insert the oat below

this tab.

Insert the tab on

the other side of the

oat into the hole.

Insert the tab of the

oat into the hole.

1

Fill Humidifying Tray halfway

with lukewarm water, add a

small amount of mild kitchen

detergent, and leave to soak

for about 30 minutes.

Dilute detergent according to

instructions on the container.

Clean difcult-to-reach parts

with a cotton swab or tooth

brush.

2

Rinse the Humidifying

Tray with lukewarm water.

• Rinse until all detergent residue

is removed.

• Inadequate rinsing may

cause the detergent

odor or changes

in the shape/ color

of the main unit.

4

Replace the Humidifying lter and re-

place the Humidifying Tray in the unit.

The Humidifying lter will not

t if placed in backwards. Be

sure there is no gap between

the Humidifying tray and the

unit when the Humidifying Tray

is replaced in the unit. The unit

may not operate properly if the

Humidifying Tray is not prop-

erly replaced in the unit.

Do not hold

this part.

2

Remove the Water Tank and Humidifying

lter from the Humidifying Tray. Drain ac-

cumulated water by tilting the Humidify-

ing Tray slowly.

Color:Gray

HUMIDIFYING TRAY

1 month

Care Cycle

Humidifying lter

KC-850U_Eng.indd 17 10.4.14 10:35:12 AM

E-18

CARE AND MAINTENANCE

HUMIDIFYING FILTER

Frequency of maintenance cycle will depend on the hardness or the impuri

ties of the water

that you use; the harder the water the more often descaling will be necessary.

1

Remove the Water Tank and

Humidifying Tray.

2

Remove the Humidifying lter

from the Humidifying Tray.

Avoid spilling water from the Humidifying Tray.

3

Preparing the descaling solu-

tion.

Citric acid, available at some drugstores,

or 100% bottled lemon juice are used for

descaling. Choose either one to use, and

prepare the descaling solution.

Dissolve 3 teaspoons of citric acid and 2

1/2 cups of lukewarm water in a suitable

container, and stir well.

100% bottled lemon juice can be used for

descaling. Use only 100% bottled lemon

juice with no pulp (strain juice if neces-

sary). Combine 1/4 cup lemon juice and

3 cups of lukewarm water in a container

large enough to hold the Humidifying lter

and stir well.

4

Pre-soak the Humidifying lter

in the solution for 30 minutes

before cleaning.

When using lemon juice,

it is recommended to pre-

soak longer than citric

acid.

5

Rinse the Humidifying lter

repeatedly with lukewarm water

to remove all the solution resi-

due.

Inadequate rinsing may cause odor and

affect the performance and/or appear-

ance of the unit.

Water Tank

Humidifying

Tray

Humidifying lter

Humidifying

Tray

Pay attention not to spill water when cleaning the lter.

Care Cycle Once a month or when the Filter Indicator Light is on.

* Do not scrub the Humid-

ifying filter, rinse gently

under lukewarm water

only.

6

Attach the Humidifying lter to

the Humidifying Tray, and re-

place the Humidifying Tray in

the unit.

• The Humidifying filter will not fit if

placed in backwards. Be sure there is

no gap between the Humidifying tray

and the unit when the Humidifying Tray

is replaced in the unit. The unit may not

operate properly if the Humidifying Tray

is not properly replaced in the unit.

• When not using the

unit for a long pe-

riod of time, dry the

Humidifying filter

completely before

replacing.

7

Plug in the unit, turn power ON,

and press the Filter Reset But-

ton on the display more than 3

seconds to reset.

You may notice reddish-brown or white

deposits forming on the surface of the

Humidifying lter. These impurities (cal-

cium, etc.) are due to the impurities con-

tained in tap water; this is not a defect.

Replace the Humidifying lter when it is

covered completely in white deposits.

KC-850U_Eng.indd 18 10.4.14 10:35:12 AM

La page charge ...

Sharp KC-860U Manuel utilisateur

Ce manuel convient également à

Sharp KC-860U Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents