Wagan JumpBoost V8 Air Manuel utilisateur

JumpBoost

™

V8 Air

Item No. / Artículo N

o

/ Article n° : 7552

User’s Manual / Manual de Usuario / Guide d’Utilisation

CHARGE UNIT FOR 48 HOURS BEFORE FIRST USE.

CARGUE LA UNIDAD DURANTE 48 HORAS ANTES DEL PRIMER USO.

CHARGER L’UNITÉ PENDANT 48 HEURES AVANT LA PREMIÈRE UTILISATION.

We are constantly improving our products so speciﬁcations are subject to change

without notice. Visit our website for the latest product information.

Estamos mejorando nuestros productos constantemente, por lo tanto, las especiﬁcaciones están sujetas a cambios

sin previo aviso. Visite nuestro sitio web para obtener la información más reciente de los productos.

Nous améliorons constamment nos produits, alors les spéciﬁcations sont sujettes à changement sans

préavis. Visitez notre site Web, pour obtenir les dernières informations sur nos produits.

BC

JumpBoost™ V8 Air by Wagan Tech

®

www.wagan.com

2

CONTENTS

Important Information �� 5

General Warnings �� 5

Storage �� 5

Proper Disposal �� 5

Product Features �� 6

Speciﬁcations �� 6

Front View �� 7

Rear View �� 8

Battery Status �� 9

Charging the JumpBoost �� 9

AC Charging .................................................................................................................. 9

DC Charging in Your Vehicle or Boat ................................................................................9

Jump Starter �� 10

Warnings ..................................................................................................................... 10

Procedure .................................................................................................................... 10

Air Compressor �� 12

Procedure .................................................................................................................... 12

DC Output Socket �� 13

USB Power Port �� 13

Worklight �� 13

Wagan Tech and wagan.com are trademarks used by Wagan Corporation.

User’s Manual—Read before using this equipment

www.wagan.com

3

CONTENIDO

Información Importante �� 14

Advertencias generales �� 14

Almacenamiento �� 14

Manera correcta de desechar la unidad �� 14

Características del producto�� 15

Especiﬁcaciones�� 15

Vista frontal �� 16

Vista posterior �� 17

Estado de la batería �� 18

Cómo cargar la JumpBoost �� 18

Carga por corriente CA ................................................................................................. 18

Carga por corriente CC en su vehículo o bote ................................................................. 19

Puente de arranque �� 19

Advertencias ................................................................................................................ 19

Procedimiento ............................................................................................................... 20

Compresor neumático �� 21

Procedimiento ............................................................................................................... 21

Enchufe de salida de CC �� 22

Puerto de alimentación USB �� 22

Luz de trabajo �� 22

JumpBoost™ V8 Air by Wagan Tech

®

www.wagan.com

4

TABLE DES MATIÈRES

Renseignement important �� 23

Avertissements généraux �� 23

Entreposage �� 23

Élimination appropriée �� 23

Caractéristiques du produit �� 24

Spéciﬁcations �� 24

Vue avant �� 25

Vue arrière �� 26

État de la batterie �� 27

Recharge CA ................................................................................................................ 27

Recharge CC dans un véhicule ou un bateau ................................................................... 28

Démarreur d'appoint �� 28

Avertissements .............................................................................................................. 28

Procédure ....................................................................................................................29

Compresseur d'air �� 30

Procédure ....................................................................................................................30

Prise de sortie CC �� 31

Port d'alimentation USB .................................................................................................... 31

Lampe de travail �� 31

Wagan Tech and wagan.com are trademarks used by Wagan Corporation.

User’s Manual—Read before using this equipment

www.wagan.com

5

Thank you for purchasing the JumpBoost™ V8 Air by Wagan Tech

®

. With normal care and

proper treatment, it will provide years of reliable service.

IMPORTANT INFORMATION

• Please read and understand all warnings, cautions, and notes included in this manual before

using the JumpBoost

™

V8 Air. Follow instructions provided by your vehicle manufacturer and

other devices intended to be used with this unit. Keep these instructions for future reference.

• Make sure the JumpBoost is fully charged before ﬁrst use. We recommend 48 hours for

initial charge.

GENERAL WARNINGS

• This appliance is NOT intended for use by persons with reduced physical, sensory, or

mental capabilities.

• Children or persons lacking in experience and knowledge also should NOT operate this

appliance unless he/she has been given supervision or instruction concerning the proper

usage and warnings of the appliance by a person responsible for their safety.

• For proper and safe operation of any accessory outlet, do not place anything in it except

the plug of the accessory to be used.

• Use only the chargers, cables, and clamps provided. Unauthorized parts may damage

the unit.

• This product has no consumer serviceable parts other than the external fuse. Do not

attempt to open the unit’s enclosure, doing so will void the warranty.

STORAGE

This unit may be stored in any position. Make sure the clamps and air hose are securely tucked

away in their original positions. Store in a cool, dry area. If the unit is not used for a prolonged

period of time, recharge every 3 months.

PROPER DISPOSAL

• Appliance, accessories, and packaging should be recycled in an environmentally friendly

manner. Plastic parts are coded for purposes of separation when recycling.

• Accumulators and battery-powered electrical appliances contain materials which are

harmful to the environment. Do not dispose of batteries and/or electric/electronic appliances

in normal household refuse. When the battery has reached the end of its lifetime, please

take the entire unit to a battery recycling facility.

JumpBoost™ V8 Air by Wagan Tech

®

www.wagan.com

6

PRODUCT FEATURES

• Powerful jump starter with heavy-duty cables and clamps.

• LED indicator for checking battery status.

• High- pressure air compressor for inﬂating tires and sports equipment with easy-read analog

pressure gauge.

• DC accessory outlet for powering DC appliances.

• USB power port for charging mobile devices.

• Bright, long-lasting LED worklight.

• AC/DC recharging adapter & DC recharging cable (fused) included.

SPECIFICATIONS

Battery AGM Sealed lead acid, 12V, 12 Ah

Peak Amps 1,000A

Cranking Amps 300A

Jumper Cables 5 AWG, 24-inch

Air Compressor 260 PSI, analog gauge

DC Socket 12V, 10A max,120W

USB Power Port (x1) 5V, 2.1A

Work Light COB LED, 200 lumens

Charging Time (AC) 30 hours

Charging Time (DC—with engine running) 10 hours

Dimensions HxWxD (inches) 11 x 10.5 x 6.5

Weight (lb) 12.0

AC Charging Adapter Output 12V, 500mA DC

Wagan Tech and wagan.com are trademarks used by Wagan Corporation.

User’s Manual—Read before using this equipment

www.wagan.com

7

FRONT VIEW

1. LED Worklight

2. Worklight Switch

3. DC Socket

4. Reverse Polarity Indicator

5. USB Power Port

6. Battery Status Indicators

7. Battery Status Button

8. Charging Indicators

9. Charging Jack

3

2

5

6

1

4

7

9

8

JumpBoost™ V8 Air by Wagan Tech

®

www.wagan.com

8

REAR VIEW

10. Air Compressor Switch

11. Jumper Cable (negative)

12. Air Hose

13. Pressure Gauge

14. Jumper Safety Switch

15. Jumper Cable (positive)

11

10

15

13

14

12

Wagan Tech and wagan.com are trademarks used by Wagan Corporation.

User’s Manual—Read before using this equipment

www.wagan.com

9

BATTERY STATUS

The color LED indicators on the front of the unit provide the current state of charge on the internal

battery. It is the user’s responsibility to periodically monitor the battery’s status and recharge

every 3 months in addition to recharging after each use.

1. Disconnect any input or output power cords and turn off all switches.

2. Press and hold the Battery Status button.

3. Observe the color LED indicators to determine battery status.

• Red (only): Battery is discharged. Charge immediately.

• Red and Yellow: Battery should be charged before jumpstarting a vehicle

• Red-Yellow-Green: Partially discharged; recharge when practical.

• Red-Yellow-Green-Green: Battery is fully charged when all lights are lit

CHARGING THE JUMPBOOST

ELECTRICAL SHOCK! Exposure to water may cause electrical shock� Exposure to

water and excessive moisture will also damage the unit and void the warranty�

Charge your JumpBoost in an upright position for a full 48 hours before initial use� Continue

to maintain the life of your JumpBoost (as with all lead-acid batteries) by fully recharging the unit

every 3 months even if the JumpBoost has not been used.

AC Charging

Only use the AC charging adapter supplied with this unit� Make sure the supplied AC/DC

charging adapter is to be powered by the correct voltage (110V AC or 220V AC depending

on your country/region).

1. Make sure all JumpBoost switches are off.

2. Plug the DC end of the AC/DC charging adapter into the JumpBoost’s charging jack.

3. Connect the AC end of the AC/DC charging adapter to the wall outlet.

4. The Charging Indicator will light up during the charging process. The JumpBoost can be

charged continuously via AC adapter without damaging the internal battery.

5. When charging is complete, the Full indicator will illuminate. Disconnect the adapter from

the AC outlet ﬁrst, then from the charging jack.

6. Press the Battery Status Button and observe the Battery Status Indicators for the state of

charge on the unit’s internal battery.

DC Charging in Your Vehicle or Boat

Only use the DC charging adapter supplied with this unit� Your vehicle engine must be running

while charging the Battery Jumper. Do NOT exceed 12 hours of continuous charging time.

1. Make sure all Battery Jumper switches are off.

2. Plug the small end of the DC power cord into the JumpBoost’s charging jack.

JumpBoost™ V8 Air by Wagan Tech

®

www.wagan.com

10

3. Plug the large end of the DC power cord into an accessory (cigarette lighter) socket.

4. The Charging Indicator will light up red during the charging process. Do NOT charge for

more than 12 hours at one time�

5. When charging is complete, the green Full indicator will illuminate. Disconnect the power

cord from the accessory socket ﬁrst, then from the unit’s charging jack.

6. Press the Battery Status Button and observe the Battery Status Indicators for the state of

charge on the unit’s internal battery.

JUMP STARTER

Warnings

• Lead-acid batteries can release explosive gasses. Failure to follow instructions

may cause property damage, explosion hazard, and/or personal injury.

• Do not smoke while jump starting.

• Jump start a vehicle or boat in a well ventilated area.

• Do not attempt to jump start a frozen battery.

• This product is not intended for use in the rain or temperatures above 113 °F.

• Do not let the jumper cables or other attached appliances get wet.

• Do not wear vinyl clothing when jump starting—friction can cause static

electricity sparks.

• Remove all metal jewelry to avoid short circuits.

• Always use safety glasses when jump starting battery. Keep battery terminals clean and be

careful to keep corrosion from coming in contact with eyes—acid can cause blindness and/

or severe burns.

• Never allow red and black clamps to touch or connect to the same piece of metal—this can

cause short-circuits, power arcing, and/or explosion.

• Make sure someone is available to give assistance if needed.

• Keep out of reach of children.

Procedure

CAUTION: If the engine fails to start after three attempts, discontinue jump start procedure.

Excessive engine cranking can damage the vehicle’s starter motor. Look for other problems that

may need to be corrected or call for professional service.

1. Review the jump starter warnings.

2. Put the vehicle’s gear is in “park” position and make sure the brake is set.

3. Turn off the vehicle ignition and accessories (e.g. radios, lights, air conditioners), and

disconnect all devices such as GPS and mobile phones or tablets.

4. Turn off all JumpBoost switches and disconnect all accessories.

Wagan Tech and wagan.com are trademarks used by Wagan Corporation.

User’s Manual—Read before using this equipment

www.wagan.com

11

5. Determine the polarity of the vehicle’s battery terminals. The positive (POS, P, +) battery

terminal is usually larger in diameter than the negative (NEG, N, −) terminal. If you are

unsure, you should refer to the vehicle owner’s manual.

6. Determine the ground system of your vehicle.

• If vehicle to be started has a negative ground system (this is most common):

a. Connect the red (+) cable clamp ﬁrst to the vehicle’s positive (red) battery terminal.

b. Next, connect the black (−) clamp to the vehicle chassis or a solid, non-moving,

metal vehicle component or body part. DO NOT clamp directly to negative battery

terminal or a moving part.

• If vehicle to be started has the positive battery terminal connected to chassis (this is rare

and usually found in older car models from the 1950s or earlier):

a. Connect the black (−) clamp ﬁrst to vehicle battery’s negative (black) terminal.

b. Connect red (+) clamp to vehicle chassis or a solid, non-moving, metal vehicle

component or body part. DO NOT clamp directly to positive battery terminal or a

moving part.

7. Observe the color of the Reverse Polarity Protection Indicator to see if the clamps are

properly connected.

• If the light is RED and the unit is beeping, DO NOT TURN ON THE JUMPER

SAFETY SWITCH!

a. Cable clamps need to be reversed.

b. Disconnect the black clamp ﬁrst then the red clamp.

c. Reconnect and observe the indicator again.

• If the light is not illuminated and there is no beeping, turn on the Jumper Safety Switch.

a. Inside the vehicle, turn on the ignition switch and attempt to start the engine.

b. Crank a maximum of 3 seconds. If the engine does not start, wait 3 minutes before

the next attempt.

c. After the engine starts, turn off the Jumper Safety Switch.

d. Disconnect the clamps in the reverse order of connection prior to jumpstarting. Be

sure that the cables and clamps are securely stored.

8. Recharge the JumpBoost as soon as convenient.

JumpBoost™ V8 Air by Wagan Tech

®

www.wagan.com

12

AIR COMPRESSOR

The JumpBoost is equipped with an air compressor that can provide up to 250 PSI (pounds per

square inch) of pressure for a variety of uses such as vehicle tires and sports equipment.

CAUTION: Be careful not to over inﬂate, monitor the compressor gauge while inﬂating. Never

connect or disconnect the nozzle with the compressor operating. To avoid overheating, do

not operate the air compressor for more than 10 minutes at a time. After 10 minutes, allow the

compressor to cool for 15 minutes before using again.

Procedure

In the event that the vehicle tire is completely ﬂat, raise the vehicle using a recommended jack

before inﬂating the tire.

1. Before any tire inﬂation, look for manufacturer’s recommended inﬂation pressure.

2. Open the compartment door at the rear of the JumpBoost and extend the air hose.

3. Position the JumpBoost so that you can see the pressure gauge.

4. Make sure the chuck lever is positioned up (away from the chuck opening).

5. Determine if you will need an air hose adapter for your object.

• To inﬂate a vehicle tire:

a. Remove the valve cap from the valve stem of the tire.

b. Attach the chuck of the air hose to the tire’s valve stem.

c. Push the chuck lever down to secure the chuck to the valve stem.

• To inﬂate a sports equipment, air mattress, rafts, or other plastic inﬂatables:

a. Insert the proper valve stem adapter into stem connector as far as possible.

b. Push the chuck lever down to secure the adapter.

c. Remove the valve cap from your inﬂatable object if there is one.

d. Insert the other end of the valve stem adapter into inﬂatable’s air valve opening

as far as possible.

6. Set the Air Compressor Switch on to the “I” position to start inﬂation.

7. Monitor the pressure gauge while inﬂating the tire.

8. When recommended tire pressure has been reached, turn off the air compressor.

9. Disconnect the hose and replace valve cap.

10. Return the hose back to its compartment for storage.

11. Recharge the JumpBoost as soon as it is convenient.

Wagan Tech and wagan.com are trademarks used by Wagan Corporation.

User’s Manual—Read before using this equipment

www.wagan.com

13

DC OUTPUT SOCKET

The DC accessory socket can power a DC load up to 10 Amps. Overloading the socket will result

in tripping a self-resetting circuit breaker. Removing the overload automatically restores power to

the DC socket. For proper and safe operation of the 12 Volt DC power accessory outlet, do not

place anything into it except the 12V DC plug of the accessory to be used.

1. Check the required current draw of the appliance/device to be powered and make sure it

does not exceed the JumpBoost’s maximum wattage.

2. Open the dust cover from the DC socket.

3. Insert the 12V DC accessory plug into the socket.

4. Operate the appliance as usual.

5. After use, disconnect the accessory plug from the DC socket.

6. Replace the dust cover.

7. Recharge the JumpBoost as soon as convenient.

USB POWER PORT

• Connect a user-supplied USB cable to the USB power port on the JumpBoost.

• When charge is complete, disconnect the USB cable from the JumpBoost.

WORKLIGHT

• Press the light switch on the front of the unit to turn the light on or off.

WAGAN Corp. Limited Warranty

The WAGAN Corporation warranty is limited to products sold only in the

United States.

Warranty Duration:

Product is warranted to the original purchaser for a period of one (1) year from the

original purchase date, to be free of defects in material and workmanship. WAGAN

Corporation disclaims any liability for consequential damages. In no event will WAGAN

Corporation be responsible for any amount of damages beyond the amount paid for

the product at retail.

Warranty Performance:

During the warranty period, a product with a defect will be replaced with a comparable

model when the product is returned to WAGAN Corporation with an original store

receipt. WAGAN Corporation will, at its discretion, replace or repair the defective part.

The replacement product will be warranted for the balance of the original warranty

period. This warranty does not extend to any units which have been used in violation

of written instructions furnished.

Warranty Disclaimers:

This warranty is in lieu of all warranties expressed or implied and no representative

or person is authorized to assume any other liability in connection with the sale of our

products. There shall be no claims for defects or failure of performance or product

failure under any theory of tort, contract or commercial law including,but not limited to

negligence, gross negligence, strict liability, breach of warranty, and breach of contract.

Returns:

WAGAN Corporation is not responsible for any item(s) returned without an ofﬁcial

Return Authorization number (RA#). Please contact our customer service team by phone

or email to obtain an RA#. You can also visit our website and chat with our team

during our normal business hours. For more details and instructions on how to process

a warranty claim, please read the “Returns” section under the “Contact” page on our

website. WAGAN Corporation is not responsible for any shipping charges incurred in

returning the item(s) back to the company for repair or replacement.

Register your product online at http://tinyurl.com/wagan-registration to be added to our

email list. You will receive previews on our upcoming products, promotions, and events.

JumpBoost™ V8 Air de Wagan Tech

®

16

www.wagan.com

Gracias por su compra del JumpBoost™ V8 Air fabricado por Wagan Tech

®

. Con el cuidado

normal y el tratamiento adecuado, le ofrecerá años de servicio conﬁable.

INFORMACIÓN IMPORTANTE

• Usted debe leer y entender todas las advertencias, precauciones, y notas incluidas en este

manual antes de usar el JumpBoost™ V8 Air . Siga las instrucciones del fabricante de su

vehículo de otros dispositivos que desea usar con esta unidad. Conserve estas instrucciones

para referencia futura.

• Asegúrese de que el JumpBoost esté completamente cargado antes de usarlo por primera

vez. Recomendamos 48 horas para la carga inicial.

ADVERTENCIAS GENERALES

• Ese aparato NO está concebido para que lo usen personas con capacidad física, sensorial

o mental reducida.

• Los niños o personas carentes de experiencia y conocimientos TAMPOCO deben operar

este aparato, a menos que una persona responsable de su seguridad los supervise o se les

haya dado instrucciones y advertencias respecto del uso adecuado del aparato.

• Para una operación adecuada y segura de una toma de corriente auxiliar, no coloque nada

en ella, excepto el enchufe del accesorio que se va a usar.

• Use únicamente los cargadores, cables y abrazaderas que se proveen. Las partes no

autorizadas pueden dañar la unidad.

• Este producto no tiene partes que el consumidor pueda reparar adicionalmente al fusible

externo. No trate de abrir la cápsula de la unidad, ya que ello podría invalidar la garantía.

ALMACENAMIENTO

Esta unidad puede guardarse en cualquier posición. Asegúrese de que las abrazaderas y la

manguera de aire estén escondidas en sus posiciones originales. Guarde en un lugar fresco y

seco. Si la unidad no se usa en un período de tiempo prolongado, recárguela cada 3 meses.

MANERA CORRECTA DE DESECHAR LA UNIDAD

• El aparato, los accesorios y el empaque deben reciclarse de manera que no perjudique al

medio ambiente. Las partes de plástico están codiﬁcadas para separarlas para el reciclaje.

• Los aparatos eléctricos que funcionan con baterías contienen materiales que son dañinos

para el medio ambiente. No deseche las baterías y/o los aparatos eléctricos o electrónicos

junto con desechos domésticos normales. Cuando la batería haya llegado al ﬁn de su vida

útil, lleve la unidad completa a un lugar donde reciclen baterías.

Manual de Usuario—Leer antes de utilizar este equipo

Wagan Tech y wagan.com son marcas registradas de la Corporación Wagan.

17

www.wagan.com

CARACTERÍSTICAS DEL PRODUCTO

• Potente puente de arranque con cables y abrazaderas de alta resistencia.

• Indicador(es) LED para veriﬁcar el estado de la batería.

• Compresor del ﬂujo de aire de alta presión para inﬂar llantas y equipos deportivos con un

manómetro análogo de fácil lectura.

• Enchufe accesorio(s) de CC para alimentar aparatos de CC.

• Alimentación USB para cargar dispositivos móviles.

• Luz de trabajo LED brillante, de larga duración.

• Adaptador de recarga CA/CC y cable de recarga de CC (con fusible) incluido.

ESPECIFICACIONES

Batería AGM sellada de plomo-ácido, 12 V, 12 Ah

Amperios pico 1000 A

Ampos de arranque en frío 300 A

Cable para puente de arranque 5 AWG, 61-centímetros

Compresor de aire Manómetro análogo de 260 PSI

Enchufe de CC 12 V, 10 A máx.

Puerto de alimentación USB 5 V, 2.1 A

Luz de Trabajo LED COB, 200 lúmenes

Tiempo de carga (CA) 30 horas

Tiempo de carga (CC—con el motor funcionando) 10 horas

Medidas AxLxA (centímetros) 28.0 x 26.7 x 16.5

Peso (kilogramo) 5.4

Salida de corriente de adaptador de carga de CA 12 V, 500 mA CC

JumpBoost™ V8 Air de Wagan Tech

®

18

www.wagan.com

VISTA FRONTAL

1. Luz de trabajo LED

2. Interruptor de luz de trabajo

3. Enchufe de CC

4. Indicador de polaridad

5. Puertos de alimentación USB

6. Indicador de estado de la batería

7. Botón de estado de la batería

8. Indicador de carga

9. Toma de carga

3

2

5

6

1

4

7

9

8

Manual de Usuario—Leer antes de utilizar este equipo

Wagan Tech y wagan.com son marcas registradas de la Corporación Wagan.

19

www.wagan.com

VISTA POSTERIOR

10. Interruptor del compresor de aire

11. Cables de puente (negativo)

12. Manguera del aire

13. Manómetro

14. Conmutador de seguridad

del arrancador

15. Cables de puente (positivo)

11

10

15

13

14

12

JumpBoost™ V8 Air de Wagan Tech

®

20

www.wagan.com

ESTADO DE LA BATERÍA

Los indicadores de color LED al frente de la unidad muestra el estado actual de carga de la

batería interna. Es responsabilidad del usuario veriﬁcar periódicamente el estado de la batería y

recargarla cada 3 meses además de recargarla después de cada uso.

1. Desconecte todos los cables de entrada o de alimentación de corriente y apague todos

los interruptores.

2. Pulse y sostenga el botón de Battery Status (estado de la batería).

3. Observe el(los) indicador(es) de color de LED para determinar el estado de la batería.

• Rojo (únicamente): La batería está descargada. Cárguela de inmediato.

• Rojo y Amarillo: Debe cargarse la batería antes de arrancar un vehículo con el puente

de arranque

• Rojo-Amarillo-Verde: Descarga parcial; recargue cuando tenga la oportunidad.

• Rojo-Amarillo-Verde-Verde: Todas las luces encendidas indican carga completa

CÓMO CARGAR LA JUMPBOOST

¡DESCARGA ELÉCTRICA! La exposición al agua puede ocasionar una descarga

eléctrica� La exposición al agua y el exceso de humedad también dañarán la unidad

y anularán la garantía�

Cargue su Battery Jumper en posición vertical durante 48 horas antes de usarlo por

primera vez� Para prolongar la vida de su JumpBoost (al igual que con todas las baterías de

plomo ácido), asegúrese de recargar completamente la unidad cada 3 meses, incluso si el

JumpBoost no se ha usado.

Carga por corriente CA

Use únicamente el adaptador de carga de CA que se provee con esta unidad� Asegúrese de

que el adaptador de carga CA/CC que se provee se alimenta con el voltaje correcto (110 V CA

o 220 V CA, dependiendo de su país o región).

1. Asegúrese de que todos los interruptores del JumpBoost estén apagados.

2. Conecte el extremo CC del adaptador de carga CA/CC al enchufe de carga del

Battery Jumper.

3. Conecte el extremo CA del adaptador de carga CA/CC al enchufe de carga de la pared.

4. El indicador carga se iluminará durante el proceso de carga. El JumpBoost puede cargarse

continuamente con el adaptador de CA sin dañar la batería interna.

5. Una vez ﬁnalizada la carga, se encenderá el indicador. Desconecte el adaptador del

tomacorriente de CA primero, después del enchufe de carga.

6. Presione el botón del estado de la batería y observe el(los) indicador(es) del estado de la

batería para ver el estado de carga de la batería interna de la unidad.

La page est en cours de chargement...

Wagan JumpBoost V8 Air Manuel utilisateur

Wagan JumpBoost V8 Air Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents