Allmand LIGHT TOWER, ALLMAND, NIGHT-LITE PRO II Manuel utilisateur

Not for

Reproduction

Not for

Reproduction

2

Record Important Information

Recording the equipment information will help when placing

an order for replacement parts and/or decals.

Company Equipment No:

Unit Model No:

Unit VIN:

Engine Model No: Serial No:

Generator Model No: Serial No:

Accessories:

Manual Contents:

Introduction........................................................................... 2

Products Covered by This Manual......................................2

Safety......................................................................................2

Features And Controls......................................................... 9

Pre-Operation Checklist..................................................... 10

Transporting........................................................................ 11

Operation............................................................................. 17

Maintenance.........................................................................24

Troubleshooting..................................................................28

Specifications......................................................................28

Addendum - Unit Options.................................................. 30

Introduction

About This Manual

TAKE TIME TO READ THIS MANUAL THOROUGHLY

This instruction manual provides necessary instructions for

the Allmand

®

Night-Lite Pro II

®

Light Tower.

The information found in this manual is in effect at the time

of printing. Allmand Bros Inc. may change contents without

notice and without incurring obligation.

The images throughout this manual are representative, and

may differ from your model.

Any reference in this manual to left or right shall be

determined by looking at the trailer from the rear.

If uncertain about any of the information in the

manual, contact the Allmand service department at

1-800-562-1373, or contact us through the Allmand website,

www.allmand.com.

Save these original instructions for future reference.

Products Covered by This

Manual

The following products are covered by this manual:

Night-Lite Pro II

®

Safety

Safety Definitions

For your safety, the safety of others, and to protect the

performance of equipment, follow the precautions listed

throughout the manual before operation, during operation and

during periodic maintenance procedures.

Indicates a potential personal injury hazard.

DANGER

Indicates a hazardous situation which, if not avoided, will

result in death or serious injury.

WARNING

Indicates a hazardous situation which, if not avoided, could

result in death or serious injury.

CAUTION

Indicates a hazardous situation which, if not avoided, could

result in minor or moderate injury.

NOTICE

Information considered important but not hazard related.

Safety Precautions

The following section contains general safety precautions

and guidelines that must be obeyed to reduce risk to

personal safety. Special safety precautions are listed in

specific procedures. Read and understand all of the safety

precautions before operating or performing repairs or

maintenance.

DANGER

Electrocution Hazard

• Always check overhead wires and obstructions before

raising or lowering the light tower.

• Always obey the rules or instructions for your work

site and state, province and national electric code for

maintaining a safe distance from overhead wires.

• High voltage is present when engine is running. Never

attempt to service electrical components while engine is

running.

• Do not operate the light tower if the insulation on the

electrical cord or other electrical wiring is cut or worn or

if bare wires are exposed. Repair or replace damaged

wiring before starting the engine.

Not for

Reproduction

3

WARNING

Unsafe Operation Hazard

• Never permit anyone to install or operate the equipment

without proper training.

• Read and understand this Operator’s Manual, the

Engine Operator’s Manual, and any other component

manuals before operating or servicing the light tower

to make sure that safe operating practices and

maintenance procedures are followed.

• Safety signs and decals are additional reminders for

safe operating and maintenance techniques.

WARNING

Fall Hazard

• Never carry riders on the equipment.

WARNING

Modification Hazard

• Never modify the equipment without written consent of

the manufacturer. Any modification could effect the safe

operation of the equipment.

WARNING

Exposure Hazard

• Always wear personal protective equipment, including

appropriate clothing, gloves, work shoes, and eye and

hearing protection, as required by the task at hand.

WARNING

Rollover Hazard

• Do not raise, lower or use light tower unless all

outriggers and jacks are positioned on firm ground.

• Never move or reposition the light tower while the light

tower is extended in the vertical position.

WARNING

Fire and Explosion Hazard

Batteries give off explosive gases during recharging. Sparks

could cause explosions, resulting in death or serious injury.

Burn Hazard

Batteries contain acid, which is extremely caustic. Contact

with battery contents could cause severe chemical burns.

Shock Hazard

Batteries present a risk of electric shock and high short

circuit current.

• Always disconnect the negative (-) battery cable before

servicing equipment.

• DO NOT dispose of battery in a fire. Recycle battery.

• DO NOT allow any open flame, spark, heat, or lit

cigarette during and for several minutes after charging a

battery.

• DO NOT open or mutilate battery.

• DO NOT charge a frozen battery. Always slowly warm

the battery to room temperature before charging.

• Wear protective gloves, rubber apron, rubber boots and

rubber gloves.

• Remove watches, rings, or other metal objects.

• Use tools having insulated handles.

WARNING

Fire And Explosion Hazard

• Diesel fuel is flammable and explosive under certain

conditions.

• Never use a shop rag to catch fuel.

• Wipe up all spills immediately.

• Never refuel with the engine running.

• Store any containers containing fuel in a well ventilated

area, away from any combustibles or sources of

ignition.

WARNING

Alcohol And Drug Hazard

• Never operate the light tower while under the influence

of alcohol or drugs, or when ill.

Not for

Reproduction

4

WARNING

Entanglement / Sever Hazard

• Always stop the engine before beginning service.

• If the engine must be serviced while it is operating,

remove all jewelry, tie back long hair and keep hands,

other body parts and clothing away from moving/

rotating parts.

• Verify that all guards and covers are attached properly

to the equipment before starting the engine. Do not

start the engine if any guards or covers are not properly

installed on the equipment.

• Attach a “Do Not Operate” tag near the key switch while

performing maintenance on the equipment.

WARNING

Flying Object Hazard

• Always wear eye protection when cleaning the

equipment with compressed air or high pressure water.

Dust, flying debris, compressed air, pressurized water

or steam may injure your eyes.

WARNING

Coolant Hazard

• Wear eye protection and rubber gloves when handling

engine coolant. If contact with the eyes or skin should

occur, flush eyes and wash immediately with clean

water.

WARNING

Burn Hazard

• Opening cap on hot radiator could result in death

or serious injury. Allow radiator to cool down before

opening cap.

WARNING

Burn Hazard

• Light fixtures and some of the engine surfaces become

very hot during operation and shortly after shutdown.

• Keep hands and other body parts away from hot

surfaces.

• Handle hot components, such as light fixtures, with heat

resistant gloves.

NOTICE

• Any part which is found defective as a result of

inspection or any part whose measured value does not

satisfy the standard or limit MUST be replaced.

• Always tighten components to the specified torque.

Loose parts can cause equipment damage or cause it

to operate improperly.

• Follow the guidelines of the Environmental Protection

Agency (EPA), Environment Canada (EC) or other

governmental agencies for the proper disposal of

hazardous materials such as engine oil, diesel fuel and

engine coolant.

• Only use replacement parts specified. Other

replacement parts may effect warranty coverage.

• Clean all accumulated dirt and debris away from the

body of the equipment and its components before

you inspect the equipment or perform preventative

maintenance procedures or repairs. Operating

equipment with accumulated dirt and debris will cause

premature wear of equipment components.

• Never dispose of hazardous materials by dumping them

into a sewer, on the ground, or into groundwater or

waterways.

• Retrieve any tools or parts that may have dropped

inside of the equipment to avoid improper equipment

operation.

• If any alert indicator illuminates during equipment

operation, stop the engine immediately. Determine

the cause and repair the problem before continuing to

operate the equipment.

Safety Decals

Before operating your unit, read and understand the following

safety decals. The cautions, warnings, and instructions are for

your safety. To avoid personal injury or damage to the unit,

understand and follow all the decals.

Keep the decals from becoming dirty or torn, and replace

them if they are lost or damaged. Also, if a part needs to be

replaced that has a decal attached to it, make sure to order

the new part and decal at the same time.

If any safety or instructional decals become worn or

damaged, and cannot be read, order replacement decals

from your dealer.

US Models

DANGER- Entering electrical

compartment while equipment is

in operation will result in death

or serious injury. Shut down

equipment before entering electrical

compartment.

Part No. 107251

WARNING- Contact with hot

exhaust gases and parts could cause

death or serious injury. Avoid hot

exhaust gases. Keep hands and

combustible materials away from hot

parts.

Part No. 107465

Not for

Reproduction

5

US Models

WARNING-Opening cap on hot

radiator could result in death or

serious injury.Allow radiator to cool

downbefore opening cap.

WARNING- Contact with rotating

parts could result in death or serious

injury.Keep away from rotating

parts.

Part No. 107246



WARNING- Smoking materials,

open flames, or other forms of

ignition near the battery could

cause explosion resulting in death

or serious injury. Keep smoking

materials, open flames, or other

forms of ignition away from the

battery.

WARNING- Exposure to corrosive

materials could cause result in death

or serious injury. Wear protective

gloves when handling battery.

Part No. 108805



DANGER- Contacting power lines

when raising light tower will result in

death or serious injury. Keep light

tower far away from power lines.

WARNING- Raising light tower

without properly positioning the

outriggers and lowering jacks could

cause machine rollover resulting

in death or serious injury. Always

position the outriggers and lower

jacks on a smooth, flat, and stable

surface before raising light tower.

WARNING-Failure to lock bottom

mast latch before raising tower could

allow tower to fall resulting in death

or serious injury.Lock bottom mast

latch beforeraising tower.

CAUTION- Snow and ice could

cause uncontrolled condition in

winch that could result in minor to

moderate injury. Always check to

make sure pawl engages gear, and

apply silicone to winch as needed.

Part No. 108818



US Models

DANGER- Contacting power lines

when raising light tower will result in

death or serious injury. Keep light

tower far away from power lines.

WARNING-Failure to lock bottom

mast latch before raising tower could

allow tower to fall resulting in death

or serious injury.Lock bottom mast

latch beforeraising tower.

CAUTION- Snow and ice could

cause uncontrolled condition in

winch that could result in minor to

moderate injury. Always check to

make sure pawl engages gear, and

apply silicone to winch as needed.

Part No. 108819



WARNING- Looking at illuminated

light fixtures could result in serious

injury. Do not look directly at

illuminated light fixtures.

Part No. 108820



WARNING-Unexpected start

of engine could result in death or

serious injury.Read and follow LSC

control panel operator’s manual

before operating or servicing this

equipment.

Part No. 108821



DANGER-Contacting power lines

when raising light tower will result in

death or serious injury. Keep light

tower far away from power lines.

Part No. 108822



WARNING-Handling light fixtures

when they are hot could result in

serious injury. Keep clear of light

fixtures when illuminated or hot.

Part No. 108994



WARNING- Raising light tower

without properly positioning the

outriggers and lowering jacks could

cause machine rollover resulting

in death or serious injury. Always

position the outriggers and lower

jacks on a smooth, flat, and stable

surface before raising light tower.

Part No. 108995



Not for

Reproduction

6

US Models

WARNING- Excessive towing

speed could result in death or

serious injury. Do not exceed 65mph

(105km/h) when towing trailer.

WARNING-Failure to secure tower

in lowered position could cause light

fixtures to detach resulting in death

orserious injury.Lock light tower to

in lowered position before towing

trailer.

Part No. 108996



WARNING- Excessive towing

speed could result in death or

serious injury. Do not exceed 65mph

(105km/h) when towing trailer.

WARNING-Failure to secure light

bar and lower tower could cause light

fixtures to detach resulting in death

or serious injury.Lock light tower to

lowest position and secure light bar

before towing.

Part No. 108997



WARNING-Performing high speed

sharp turns could cause trailer to roll

over resulting in death or serious

injury. Slow to a safe speed when

performing sharp turns.

WARNING-Failure to follow

warnings, instructions, and operator’s

manual could result in death or

serious injury.Open left door to

locate operator’s manual. Read

and follow operator’s manual

before operating or servicing this

equipment.

Part No. 108998



US Models

WARNING-Standing under light

tower mast and fixtures during

lowering operation could result

in death or serious injury.Keep

bystanders away from light tower

during lowering and raising

operations.

WARNING-Handling light fixtures

when they are hot could result in

death or serious injury.Keep clear of

light fixtures when illuminated or hot.

WARNING-Looking at illuminated

light fixtures could result in serious

injury.Do not look directly at

illuminated light fixtures.

Part No. 108999



DANGER-Failure to use ground

rod will result in death or serious

injury.Drive ground rod into earth

and attach ground wire to grounding

lug on side of trailer.

DANGER-Entering electrical

compartment while equipment is

in operation will result in death

or serious injury. Shut down

equipment before entering electrical

compartment.

Part No. 109004



WARNING- Breathing diesel engine

exhaust exposes you to chemicals

known to the State of California to

cause cancer and birth defects or

other reproductive harm.

Part No. 112141

Canadian Models

CSA File Number

Part No. 110361

Machine Grounding Information

Part No. 110362

WARNING- Using this equipment

in an enclosed area can cause

asphyxiation which could result in

death or serious injury.

Part No. 110363

Non-US Models

DANGER- Entering electrical

compartment while equipment is

in operation will result in death

or serious injury. Shut down

equipment before entering electrical

compartment.

Part No. 104480

Not for

Reproduction

7

Non-US Models

WARNING- Contact with hot

exhaust gases and parts could cause

death or serious injury. Avoid hot

exhaust gases. Keep hands and

combustible materials away from hot

parts.

Part No. 107529

DANGER- Contacting power lines

when raising light tower will result in

death or serious injury. Keep light

tower far away from power lines.

WARNING- Raising light tower

without properly positioning the

outriggers and lowering jacks could

cause machine rollover resulting

in death or serious injury. Always

position the outriggers and lower

jacks on a smooth, flat, and stable

surface before raising light tower.

WARNING-Failure to lock bottom

mast latch before raising tower could

allow tower to fall resulting in death

or serious injury.Lock bottom mast

latch beforeraising tower.

CAUTION- Snow and ice could

cause uncontrolled condition in

winch that could result in minor to

moderate injury. Always check to

make sure pawl engages gear, and

apply silicone to winch as needed.

Part No. 107250



WARNING- Looking at illuminated

light fixtures could result in serious

injury. Do not look directly at

illuminated light fixtures.

Part No. 107259



WARNING-Handling light fixtures

when they are hot could result in

serious injury. Keep clear of light

fixtures when illuminated or hot.

Part No. 107262



DANGER-Failure to use

groundrod will result in deathor

serious injury.Drive ground rod

intoearth and attach groundwire to

grounding lug onside of trailer.

DANGER-Entering electrical

compartment whileequipment is

in operation will result indeath

or serious injury.Shut down

equipment before enteringelectrical

compartment.

Part No. 107263



Non-US Models

DANGER- Contacting power lines

when raising light tower will result in

death or serious injury. Keep light

tower far away from power lines.

WARNING-Failure to lock bottom

mast latch before raising tower could

allow tower to fall resulting in death

or serious injury.Lock bottom mast

latch beforeraising tower.

CAUTION- Snow and ice could

cause uncontrolled condition in

winch that could result in minor to

moderate injury. Always check to

make sure pawl engages gear, and

apply silicone to winch as needed.

Part No. 107451



WARNING- Excessive towing

speed could result in death or

serious injury. Do not exceed 65mph

(105km/h) when towing trailer.

WARNING-Failure to secure tower

in loweredposition could cause light

fixturesto detach resulting in death

orserious injury.Lock light tower

to in loweredposition before towing

trailer.

Part No. 107452



WARNING- Excessive towing

speed could result in death or

serious injury. Do not exceed 65mph

(105km/h) when towing trailer.

WARNING-Failure to secure light

bar andlower tower could cause

lightfixtures to detach resulting in

deathor serious injury.Lock light

tower to lowest positionand secure

light bar before towing.

Part No. 107458



WARNING- Smoking materials,

open flames, or other forms of

ignition near the battery could

cause explosion resulting in death

or serious injury. Keep smoking

materials, open flames, or other

forms of ignition away from the

battery.

WARNING- Exposure to corrosive

materials could cause result in death

or serious injury. Wear protective

gloves when handling battery.

Part No. 107968



Not for

Reproduction

8

Non-US Models

WARNING- Raising light tower

without properly positioning the

outriggers and lowering jacks could

cause machine rollover resulting

in death or serious injury. Always

position the outriggers and lower

jacks on a smooth, flat, and stable

surface before raising light tower.

Part No. 107972



WARNING-Unexpected start

of engine could result in death or

serious injury.Read and follow LSC

control panel operator’s manual

before operating or servicing this

equipment.

Part No. 107978



DANGER-Contacting power lines

when raising light tower will result in

death or serious injury. Keep light

tower far away from power lines.

Part No. 107979



WARNING-Opening cap on hot

radiator could result in death or

serious injury.Allow radiator to cool

downbefore opening cap.

WARNING- Contact with rotating

parts could result in death or serious

injury.Keep away from rotating

parts.

Part No. 107986



WARNING-Performing high

speed sharpturns could cause

trailer toroll over resulting in death

orserious injury.Slow to a safe

speed whenperforming sharp turns.

WARNING-Failure to follow

warnings,instructions, and

operator’smanual could result in

deathor serious injury.Open left

door to locate operator’s manual.

Readand follow operator’s manual

before operating orservicing this

equipment.

Part No. 108216



All Models

Forklift Pocket

Part No. 107254

Light Tower Transport Alignment

Part No. 107459

All Models

Ground Lug

Part No. 107969

Mast Latch (Bottom)

Part No. 107260



Mast Latch (Top)

Part No. 107261



Operating Instructions

Part No. 107454 (Vertical Tower

Models)

Part No. 107455 (Laydown Tower

Models)

Part No. 107456 (Vertical Tower

Models with LSC)



Lifting Eye Rating

Part No. 107453



Tie-Down Point

Part No. 109005



WARNING- Do not smoke

when fueling. Stop engine before

refueling.

Ultra low sulfur fuel only (<15 MG/

KG)

Part No. 107967



Engine Oil Drain

Part No. 107973



Not for

Reproduction

9

All Models

Fluid Containment Drain

Part No. 107463



Tire Information

Part No. 111585



Operation Icons

The following table contains operation icons that may be

found on the unit, along with the meaning of each icon.

Icon Meaning Icon Meaning

Power On Light Tower

Raise

Power Off Light Tower

Lower

Engine Stop Engine Oil Drain

Engine Run Engine Coolant

Drain

Engine Start Fluid

Containment

Drain

Engine Preheat Circuit Breaker

Hourmeter Disconnecting

Circuit Breaker

Trailer Interior

Light

Earth Ground

Work Light

Features And Controls

TheAllmand

®

Night-Lite Pro II

®

Light Toweris intended for

use as a stationary lighting device to illuminate large areas.

Identify the features and controls of the machine by

comparing Figures1and2with the tables following.

SeeTransportingandOperationfor detailed information

on each feature / control.

Manual (Laydown) Tower Models

1

Ref Description

A Tongue Jack

B Safety Chains (2)

C Locking Pin

D Winch Handle

E Front Outrigger and Stabilizer Jack (2)

F Rear Stabilizer Jack

G Outrigger Retention Pin

H Left Door and Engine Access

I Tower Winch

J Lamp Fixture (4)

K Manual Tower

Hydraulic (Vertical) Tower Models

Not for

Reproduction

10

2

Ref Description

A Safety Chains (2)

B Tongue Jack

C Ball Hitch

D Lunette Ring

E Front Stabilizer Jack (2)

F Rear Stabilizer Jack

G Light Bar Park Pin

H Outrigger (2)

Pre-Operation Checklist

Perform the following checks before transporting and

operating the unit, when performing general maintenance,

and after the light tower has been stored or idle for a period of

time.

WARNING

Unsafe Operation Hazard

• Operating or transporting the machine with worn,

damaged or missing parts can result in death or serious

injury. Always replace worn, damaged or missing parts

promptly. Do not transport or operate the machine

until all worn, damaged or missing parts have been

replaced, and proper operation of the machine has

been verified.

Note:

We encourage the use of authorized replacement Allmand

parts. The warranty does not cover damage or performance

problems caused by the use of parts that are not authorized

replacement parts.

1. Check that all safety and operation decals are present

and legible. SeeSafety-Safety Decals.

2. Check that all operator's manuals (product, engine,

generator, etc.) are with the unit.

3. Check the following components for wear and damage,

and for proper operation:

a. Tongue jack

• Check for rust or damage. Repair or replace as

needed.

• Check for proper operation.

SeeTransporting-Using The Tongue Jack.

b. Hitch Assembly (trailer coupler / lunette ring)

• Check for rust or damage. Repair or replace as

needed.

• Check for proper operation.

SeeTransporting-Coupling And

Uncoupling The Trailer Hitch.

• Check hardware for proper tightness. Tighten as

needed.

c. Safety chains

• Check for rust or damage. Repair or replace as

needed.

• Check hardware for proper tightness. Tighten as

needed.

d. Trailer lighting cable

• Check for cut, frayed or bare wires. Repair or

replace as needed.

• Check connector for damage. Repair or replace

as needed.

e. Breakaway kit (if equipped)

• Check for broken or frayed wires or breakaway

cable.

• Check battery charge status.

f. Tires

• Check for wear, cuts, cracks, etc. Replace as

needed.

• Check and adjust inflation pressure.

SeeSpecificationsfor proper inflation

pressure.

g. Brakes (if equipped)

• Check brakes for proper operation and wear.

Repair as needed.

h. Axle and undercarriage

• Check for rust or damage. Repair as needed.

i. Outriggers and stabilizer jacks

Not for

Reproduction

11

• Check for rust or damage. Repair or replace as

needed.

• Check for proper operation.

SeeOperation-Using The Outriggers &

Stabilizer Jacks.

j. Electrical wiring

• Check for cut, worn or bare electrical wiring.

Repair as needed.

WARNING

Electrocution hazard

• Operating the unit with cut, worn or bare electrical

wiring could result in death or serious injury. Repair

or replace damaged wiring before operating the light

tower.

k. Engine

• Check for leaks or other signs of wear or

damage. Repair as needed.

• Check the air cleaner to be sure it is firmly

attached, and that the air cleaner seals and

hose clamps are properly secured. Check the air

cleaner element. Replace if necessary.

l. Light Tower

• Check for worn or frayed cables, hydraulic leaks,

etc. Repair as needed.

• Check and adjust the hydraulic fluid level

(hydraulic (vertical) tower models only).

SeeMaintenance-Hydraulic Pump.

m. Tower Lights

• Check for broken lenses, bulbs, etc. Repair or

replace as needed.

4. Check and adjust fluid levels.

a. Engine Oil

• Refer to the engine operator's manual for oil

recommendations, capacity, and procedures.

NOTICE

Operating engine without oil will cause engine damage.

b. Engine Coolant

• Refer to the engine operator's manual for coolant

recommendations, capacity, and procedures.

NOTICE

Operating engine without coolant will cause engine

damage.

c. Fuel

• SeeOperation-Fueling The Unitfor fuel

tank location, capacity, and fueling procedures.

Transporting

WARNING

Unsafe Operation Hazard

• Operating the equipment without proper training could

result in death or serious injury. Never allow anyone to

operate the equipment without proper training.

Before transporting, readSafety.

Preparing For Work Site Delivery

Prepare the unit for delivery to the work site, especially if it

has been stored or idle for a period of time.

WARNING

Unsafe Operation Hazard

• Operating or transporting a machine with worn,

damaged or missing parts can result in death or serious

injury. Always replace worn, damaged or missing parts

promptly. Do not operate or transport this machine

until all worn, damaged or missing parts have been

replaced, and proper operation of the machine has

been verified.

1. Perform all pre-operation checks. SeePre-Operation

Checklist.

2. Run the engine through a startup and shutdown cycle

to verify operation. SeeOperation-Operating The

Engine. Also refer to the engine operator's manual.

3. Raise and lower the light tower to verify operation.

SeeOperation-Raising And Lowering The Light

Tower.

4. Turn the tower lights on and off to verify operation.

SeeOperation-Operating The Tower Lights.

Preparing For Transport

1. Shut down the tower lights. SeeOperation-Operating

The Tower Lights.

2. Shut down the engine. SeeOperation-Operating The

Engine. Also refer to the engine operator's manual

3. Lower the light tower and adjust the tower lights into

the transport position. SeeOperation-Raising And

Lowering The Light TowerandOperation-Adjusting

The Tower Lights.

WARNING

Tip Hazard

• Failure to lower the light tower into the transport

position before transporting could result in death or

serious injury. Always lower the light tower into the

transport position before transporting.

Not for

Reproduction

12

WARNING

Burn Hazard

• Handling the tower lights while hot could result in

serious injury. Allow lights to cool before handling or

use heat-resistant gloves.

4. Retract the outriggers and stabilizer jacks.

SeeOperation-Using The Outriggers & Stabilizer

Jacks.

5. Close and lock all access doors.

Towing

Maximum highway speed is 55 mph (90 km/h). Maximum off-

highway speed is 10 mph (16 km/h). Do not exceed these

speed limits.

WARNING

Unsafe Operation Hazard

• Towing the light tower trailer at highway speeds in

excess of 55 mph (90 km/h) could result in death or

serious injury. Do not tow the light tower trailer at

highway speeds in excess of 55 mph (90 km/h).

Tow vehicle / hitch requirements

1. Check the Gross Vehicle Weight Rating (GVWR) of the

light tower trailer. SeeSpecifications.

2. Check the rated towing capacity of the tow vehicle and

hitch. Both must meet or exceed the GVWR of the light

tower trailer.

Note:Check the vehicle owner's manual and hitch owner's

manual for rated towing capacities.

WARNING

Towing Hazard

• Using a tow vehicle or hitch with a rated towing capacity

less than the GVWR of the light tower trailer could

result in death or serious injury. Use only a tow vehicle

and hitch with a rated towing capacity that meets or

exceeds the GVWR of the light tower trailer.

Check the tow vehicle hitch type

The light tower trailer is designed for the following types of

tow vehicle hitches:

• 2" (50,8mm) ball hitch

• Pintle hitch

Be sure the tow vehicle is equipped with either of these hitch

types. Install if needed.

WARNING

Unsafe Operation Hazard

• Failure to use a tow vehicle hitch that mates with the

trailer hitch assembly could result in death or serious

injury. Use only a tow vehicle hitch that mates with the

trailer hitch assembly.

Reversing the trailer hitch assembly

The trailer hitch assembly is reversible. Use the trailer coupler

(A, Figure3) for ball hitches, or the lunette ring (B) for pintle

hitches. To reverse the trailer hitch assembly:

1. Remove the mounting hardware (C, Figure3).

2. Reverse the trailer hitch assembly.

Note:Use the set of mounting holes in the trailer tongue that

will keep the trailer as level as possible when connected to

the tow vehicle.

3. Reinstall the hardware. Tighten securely.

WARNING

Unsafe Operation Hazard

• Failure to properly install the trailer hitch assembly

could result in death or serious injury. Install the trailer

hitch assembly properly, and tighten the hardware

securely.



3

Connect the light tower trailer to the tow vehicle

1. Chock the wheels.Position a wheel chock firmly against

the front and rear of the wheel (A, Figure4) on each side

of the light tower trailer.



Not for

Reproduction

13

4

2. Use the tongue jack to raise the trailer tongue.

SeeTransporting-Using The Tongue Jack.

3. Position the tow vehicle hitch under the trailer hitch.

4. Couple the trailer hitch to the tow vehicle hitch.

SeeTransporting-Coupling And Uncoupling The

Trailer Hitch.

5. Connect the safety chains.

WARNING

Unsafe Operation Hazard

• Failure to properly install safety chains could result in

death or serious injury. Always properly install safety

chains.

a. Connect the safety chains (A, Figure5) to the safety

chain pockets on the tow vehicle. Criss-cross the

chains under the hitch to cradle the hitch in the event

of a disconnect.

b. Rig the chains as tightly as possible while allowing

enough slack to permit free turning.

6. Connect the trailer lighting cable.

a. Make sure the trailer lighting cable mates with the

tow vehicle lighting cable. If needed, install the proper

cable and/or connector to the tow vehicle.

b. Connect the trailer lighting cable to the tow vehicle

lighting cable (B, Figure5).

c. Make sure there is adequate slack to allow for turning

without allowing the cable to drag on the ground.

d. Check the trailer lights for proper operation.

WARNING

Unsafe Operation Hazard

• Failure of trailer lights to operate properly could result

in death or serious injury. Always check for proper

operation of trailer lights, and repair or replace as

needed.

5

7. Retract the tongue jack. SeeTransporting-Using The

Tongue Jack.

8. Remove the wheel chocks.

The trailer is now ready for towing.

To disconnect the trailer from the tow vehicle

1. Chock the wheels.

2. Deploy the tongue jack. SeeTransporting-Using The

Tongue Jack.

3. Disconnect the trailer lighting cable from the tow vehicle

lighting cable.

4. Remove the safety chains from the safety chain pockets

on the tow vehicle.

5. Uncouple the trailer hitch from the tow vehicle hitch.

SeeTransporting-Coupling And Uncoupling The

Trailer Hitch.

6. Move the tow vehicle away from the unit.

Not for

Reproduction

14

Using The Tongue Jack

The unit is equipped with a tongue jack to raise and lower the

trailer tongue, and to level the trailer front-to-rear.

To deploy the tongue jack

1. Remove the jack locking pin (A, Figure 6).

2. Rotate the tongue jack 90° into the operating position (B,

Figure 6). Install the jack locking pin (C).

WARNING

Unsafe Operation Hazard

• Failure to install the jack locking pin could result in

death or serious injury. Be sure the tongue jack is

locked in the operating position with the jack locking

pin.

3. Unfold the jack handle into the operating position (D,

Figure 6).

To lower the jack foot (raise the trailer tongue)

• Turn the jack handle counterclockwise (E, Figure 6) to

lower the jack foot (F) and raise the trailer tongue.

To raise the jack foot (lower the trailer tongue)

• Turn the jack handle clockwise (G, Figure 6) to raise the

jack foot (H) and lower the trailer tongue.

To retract the tongue jack

1. Be sure the trailer is securely supported by the tow

vehicle or other approved means.

WARNING

Unsafe Operation Hazard

• Failure to support the trailer tongue before retracting

the tongue jack could result in death or serious injury.

Be sure the trailer tongue is securely supported before

retracting the tongue jack.

2. Fully raise the jack foot.

3. Fold the jack handle into the transport position (I, Figure

6).

4. Remove the jack locking pin (J, Figure 6).

5. Rotate the tongue jack 90° into the transport position (K,

6). Install the jack locking pin (L).

6

Coupling And Uncoupling The Trailer Hitch

Trailer Coupler (for ball hitches)

To couple to the tow vehicle ball hitch

1. Pull up on the locking trigger (A, Figure7), and lift the

locking lever (B, shown lifted).

2. Use the tongue jack to lower the trailer coupler

socket (C, Figure7) fully onto the hitch ball (F).

SeeTransporting-Using The Tongue Jack.

3. Adjust the coupler clamp (D, Figure7) using the adjusting

nut (E). Tighten the adjusting nut by turning the nut

clockwise, or loosen by turning counter-clockwise. Proper

adjustment is obtained when the coupler is as tight as

possible on the hitch ball and the locking lever can still be

opened and closed.

WARNING

Unsafe Operation Hazard

• Failure to properly adjust the coupler clamp could result

in death or serious injury. Adjust the coupler clamp, and

check adjustment frequently.

4. Push the locking lever down into the locked position.

Insert the locking pin (G, Figure7) into the hole in the

locking lever, or use a padlock for added security.

5. Check to be sure the coupler is securely attached to the

ball hitch.

To uncouple

Not for

Reproduction

15

1. Remove the locking pin (or padlock, if used) from the hole

in the locking lever.

2. Pull up on the locking trigger, and lift the locking lever.

3. Use the tongue jack to raise the trailer coupler until it

clears the hitch ball. SeeTransporting-Using The

Tongue Jack.

7

Lunette Ring (for pintle hitches)

To couple to the tow vehicle pintle hitch

1. Open the locking latch (C, Figure8) on the tow vehicle

pintle hitch (A).

Note:Standard pintle hitch shown; designs vary.

2. Use the tongue jack to lower the lunette ring (B, Figure8)

into the pintle hitch hook. SeeTransporting-Using The

Tongue Jack.

3. Close the locking latch. Insert the locking pin (D, Figure8)

into the hole in the locking latch.

To uncouple

1. Remove the locking pin from the hole in the locking latch.

2. Open the locking latch.

3. Use the tongue jack to raise the lunette ring until it clears

the pintle hitch hook. SeeTransporting-Using The

Tongue Jack.

8

Lifting

Lifting equipment requirements

• Use only approved lifting equipment with a rated

lifting capacity that exceeds the GVWR of the unit.

SeeSpecifications.

WARNING

Unsafe Operation Hazard

• Failure to use approved lifting equipment with a rated

lifting capacity that exceeds the GVWR of the unit could

result in death or serious injury. Use only approved

lifting equipment with a rated lifting capacity that

exceeds the GVWR of the unit.

Before lifting

• Be sure the light tower is fully lowered and locked in

the transport position. SeeOperation-Raising And

Lowering The Light Tower.

WARNING

Rollover Hazard

• Failure to lower the light tower before lifting the unit

could result in death or serious injury. Always lower the

light tower before lifting the unit.

Lifting points

• Forklift pockets - (A, Figures9and10) Use forklift blades

at least 60" (152 cm) long when lifting the unit. Insert the

forklift blades fully into the forklift pockets.

• Lifting eye - (B, Figures9and10) Use only shackles or a

locking type hook when using the lifting eye.

• On manual (laydown) tower models, the lifting eye and

upper forklift pocketsare incorporated into the light tower

assembly. Be sure the light tower is lowered and locked

in the transport position before lifting the unit.

Not for

Reproduction

16

WARNING

Unsafe Operation Hazard

• Failure to use the designated lifting points to lift the

unit could result in death or serious injury. Use only the

designated lifting points to lift the unit.

WARNING

Unsafe Operation Hazard

• Failure to properly lower and lock the tower could result

in death or serious injury. Always be sure to properly

lower and lock the tower before attempting to lift the

unit.

WARNING

Crush Hazard

• Standing under or near the unit while it is being lifted

could result in death or serious injury. Never stand

under or near the unit while it is being lifted.

9

10

Transporting On A Trailer

Three tie-down points, located on the bottom rear of the

trailer and the underside of the trailer tongue (A, Figure11),

are used to secure the unit to a transport trailer.

Note:All models have similar tie-down point locations.

WARNING

Unsafe Operation Hazard

• Failure to use the designated tie-down points to secure

the unit to the transport trailer could result in death or

serious injury. Always use the designated tie-down

points to secure the unit to the transport trailer.

1. Secure the unit at the tie-down points with appropriately

rated chains or straps.

WARNING

Unsafe Operation Hazard

• Failure to use appropriately rated chains or straps to

secure the unit to the transport trailer could result in

death or serious injury. Always use appropriately rated

chains or straps to secure the unit to the transport

trailer.

2. Do not apply more than 600 lbs (272 kg) force on the

chains or straps.

3. The truck operator is responsible for securing the load

properly to the transport trailer.

Not for

Reproduction

17

11

Operation

Before operating, readSafety.

Choosing The Work Site

1. Obey state, province and federal rules and regulations, as

well as rules or instructions for the work site.

2. Consider the following when choosing a work site:

1. Ground surface

• Set up on smooth, flat, solid ground surfaces

only.

• Do not set up on inclines of more than 2.8° (5%

grade) front-to-back and side-to-side.

WARNING

Rollover Hazard

• Setting up the unit on soft or unstable ground, or on

inclines of more than 2.8° (5% grade), could result in

death or serious injury. Set up the unit only on smooth,

flat solid ground surfaces with inclines of no more than

2.8° (5% grade).

2. Overhead obstructions

• Consider the height of the light tower when fully

raised. SeeSpecifications.

• Avoid areas with:

• Trees

• Power lines

DANGER

Electrocution Hazard

• Raising the light tower in the presence of electrical

power lines will result in death or serious injury. Always

check for overhead wires and obstructions before

raising the light tower.

• Other overhead obstructions

3. Wind

• The unit is designed to operate in winds up

to 53 mph (85 km/h). Do not operate in winds

exceeding 53 mph (85 km/h).

WARNING

Rollover Hazard

• Operating in winds over 53 mph (85 km/h) could result

in death or serious injury. Never operate in winds

exceeding 53 mph (85 km/h).

Setting Up The Unit

1. Position the unit at the work site.

SeeOperation-Choosing The Work Site.

2. Chock the wheels. SeeTransporting–Towing.

3. If the unit was towed to the work site, disconnect from

the tow vehicle. SeeTransporting–Towing.

4. Level the trailer using the tongue jack.

SeeTransporting–Using The Tongue Jack.

5. Deploy the outriggers and stabilizer jacks.

SeeOperation-Using The Outriggers & Stabilizer

Jacks.

6. Adjust the tower lights. SeeOperation–Adjusting The

Tower Lights.

7. Raise the light tower. SeeOperation–Raising And

Lowering The Light Tower.

8. The unit is now set up and ready for operation.

Using The Outriggers And Stabilizer

Jacks

WARNING

Rollover Hazard

• Failure to deploy the outriggers and stabilizer jacks

could result in death or serious injury. Always deploy

the outriggers and stabilizer jacks before raising the

light tower.

There is one outrigger and stabilizer jack on the right front

and left front of the unit, and one stabilizer jack on the center

rear of the unit.

To deploy

1. Raise the outrigger locking pin (A, Figure12).

2. Fully extend the outrigger (B, Figure12) until the locking

pin engages the outrigger in the operating position.

WARNING

Rollover Hazard

Failure to lock the outrigger in the operating position could

result in death or serious injury. Be sure the outrigger is

locked in the operating position.

Not for

Reproduction

18

3. Remove the stabilizer jack locking pin (C, Figure12).

4. Rotate the stabilizer jack (D, Figure12) 90° into the

operating position, and install the stabilizer jack locking

pin. Make sure the pin is inserted fully through the

stabilizer jack.

WARNING

Rollover Hazard

• Failure to lock the stabilizer jack in the operating

position with the stabilizer jack locking pin could result

in death or serious injury. Be sure the stabilizer jack is

locked in the operating position with the stabilizer jack

locking pin.

5. Unfold the jack handle (E, Figure12) to the operating

position.

6. Turn the jack handle counterclockwise (F, Figure12)

until the jack foot (G) is firmly planted on the work site

surface.

7. Repeat for the remaining outriggers and stabilizer jacks.

8. Once all outriggers and stabilizer jacks are deployed, use

the stabilizer jacks and tongue jack to help level the unit

on the work site ground.

To retract

1. Turn the jack handle clockwise to fully raise the jack foot.

2. Fold the jack handle to the transport position.

3. Remove the stabilizer jack locking pin.

4. Rotate the jack 90° to the transport position, and install

the stabilizer jack locking pin. Make sure the pin is

inserted fully through the stabilizer jack.

5. Raise the outrigger locking pin.

6. Retract the outrigger into the transport position. Be sure

the locking pin engages.

WARNING

Unsafe Operation Hazard

• Failure to lock the outrigger in the transport position

could result in death or serious injury. Be sure the

outrigger is locked in the transport position.

7. Repeat for the remaining outriggers and stabilizer jacks.

12

Adjusting The Tower Lights

WARNING

Burn Hazard

• Adjusting the tower lights while the lights are on could

result in serious injury. Turn the lights off and wait 10

minutes to cool before adjusting the tower lights.

Note:The tower lights must be adjusted to the preferred work

angle before raising the light tower.

To adjust for operation

Manual (laydown) towers

1. Set each individual light fixture to the preferred work

angle.

• Yoke center pivot (A, Figure13) - adjusts the

horizontal angle of each individual light fixture. Grasp

the sides of the yoke (B) to adjust.

• Fixture pivots (C, Figure13) - adjust the vertical angle

of each individual light fixture. Move the light fixture

(D) up or down to adjust.

2. The light tower can also be rotated to provide additional

adjustment of the light angle. SeeOperation-Raising

And Lowering The Light Tower.

Not for

Reproduction

19

13

Hydraulic (vertical) towers - metal halide

1. Set the light bar to the preferred work angle.

a. Pull the park pin (A, Figure14) and rotate 90° to

unlock the light bar.

b. Rotate the light bar to the preferred work angle.

c. If the light bar rotates loosely or does not remain in

the preferred work position:

• Remove the cap plug from the center of the light

bar.

• Tighten the pivot nut until desired resistance is

achieved.

• Replace the cap plug.

2. Set the tower arms to the preferred work angle.

a. Loosen the adjustment nut (B, Figure14) on each

tower arm.

Note:Six-light models also feature a park pin similar to the

light bar. Pull and rotate 90° to retract.

b. Rotate each tower arm to the preferred work angle.

c. Tighten the adjustment nuts.

Note:On six-light models, lock each tower arm with the park

pin.

3. Set each individual light fixture to the preferred work

angle.

• Yoke center pivot (C, Figure14) - adjusts the

horizontal angle of each individual light fixture. Grasp

the sides of the yoke to adjust.

• Fixture pivots (D, Figure14) - adjust the vertical angle

of each individual light fixture. Move the light fixture

up or down to adjust.

14

Hydraulic (vertical) towers - LED

Note:Six-light model shown. Four-light model similar.

1. Set the light bar to the preferred work angle.

a. Pull the park pin (A, Figure15) and rotate 90° to

unlock the light bar.

b. Rotate the light bar to the preferred work angle.

c. If the light bar rotates loosely or does not remain in

the preferred work position:

• Remove the cap plug from the center of the light

bar.

• Tighten the pivot nut until desired resistance is

achieved.

• Replace the cap plug.

2. Set the tower arms to the preferred work angle.

a. Loosen the adjustment nut (B, Figure15) on each

tower arm.

Note:Six-light models also feature a park pin (C) similar to

the light bar. Pull and rotate 90° to retract.

b. Rotate each tower arm to the preferred work angle.

c. Tighten the adjustment nuts.

Note:On six-light models, lock each tower arm with the park

pin.

3. Set each individual light fixture to the preferred work

angle.

• Yoke center pivot (D, Figure15) - adjusts the

horizontal angle of each individual light fixture. Grasp

the sides of the yoke to adjust.

• Fixture pivots - adjust the vertical angle of each

individual light fixture. Loosen the adjustment nut

(E, Figure15), move the light fixture up or down to

adjust, then tighten the adjustment nut.

Not for

Reproduction

20

15

To adjust for transport / storage

Manual (laydown) towers

1. Rotate the fixture yokes 90° (perpendicular) to the light

bar. See Figure16

2. Turn the light fixtures to face inward toward center.

16

Hydraulic (vertical) tower models

1. Set the light bar to the transport position.

a. Rotate the light bar front-to-back. See Figure17

b. Pull the park pin and rotate 90° to lock the light bar.

2. Set the tower arms to the transport position.

a. Loosen the adjustment nut on each tower arm.

Note:On six-light models, pull and rotate the park pin to

retract.

b. Rotate each tower arm to set the light fixture yokes to

a horizontal position. See Figure17.

c. Tighten the adjustment nuts.

Note:On six-light models, also rotate and lock the park pin.

3. Rotate the fixture yokes parallel to the light bar.

4. Turn the light fixtures to face inward toward center. See

Figure17.



17

Raising And Lowering The Light Tower

WARNING

Crush Hazard

• Raising or lowering the light tower with obstructions

or people near the light tower could result in death or

serious injury. Be sure the area is clear of people and

obstructions before raising or lowering the light tower.

Manual (Laydown) Towers

To raise the light tower

1. Unlatch the tower locking pin (B, Figure18).

2. Turn the winch handle (C, Figure18) clockwise until the

light tower (A) is vertical.

3. Lock the light tower in the operating position with the latch

pin (E, Figure18).

WARNING

Unsafe Operation Hazard

• Failure to lock the light tower in the operating position

could result in death or serious injury. Be sure to lock

the light tower in the operation position.

4. Turn the winch handle (D, Figure18) on the light tower

clockwise to raise the telescoping masts to the preferred

height.

To rotate the light tower to the preferred work angle

La page charge ...

Allmand LIGHT TOWER, ALLMAND, NIGHT-LITE PRO II Manuel utilisateur

Ce manuel convient également à

Allmand LIGHT TOWER, ALLMAND, NIGHT-LITE PRO II Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents