Greenlee CM-410 Digital Clamp-on Meter Manual Manuel utilisateur

CM-410

Digital

Clamp-on Meter

Medidor digital

con pinza

Contrôleur

numérique

à pince

INSTRUCTION MANUAL

MANUAL DE INSTRUCCIONES

MANUEL D’INSTRUCTIONS

Read and understand all of the instructions and

safety information in this manual before

operating or servicing this tool.

Lea y entienda todas las instrucciones y la

información sobre seguridad que aparecen en

este manual, antes de manejar esta herramienta

o darle mantenimiento.

Lire attentivement et bien comprendre toutes les

instructions et les informations sur la sécurité de

ce manuel avant d‘utiliser ou de procéder à

l‘entretien de cet outil.

2

Description

The Greenlee CM-410 Digital Clamp-on Meter is a hand-held testing device

capable of measuring up to 400 amps of alternating current, in addition to

measuring AC or DC voltage, resistance, and checking continuity.

Safety

Safety is essential in the use and maintenance of Greenlee tools and

equipment. This instruction manual and any markings on the tool provide

information for avoiding hazards and unsafe practices related to the use of

this tool. Observe all of the safety information provided.

Purpose of This Manual

This instruction manual is intended to familiarize all personnel with the

safe operation and maintenance procedures for the Greenlee CM-410

Digital Clamp-on Meter.

Keep this manual available to all personnel.

Replacement manuals are available upon request at no charge:

www.greenlee.com.

KEEP THIS MANUAL

All specifications are nominal and may change as design improvements occur.

Greenlee

Tools,

Inc. shall not be liable for damages resulting from misapplication or

misuse of its products.

® Registered: The color green for electrical test instruments is a registered trademark

of Greenlee

Tools,

Inc.

Do not discard this product or throw away!

For recycling information, go to www.greenlee.com.

3

CM-410

Important Safety Information

Electric shock hazard:

Contact with live circuits could result in severe

injury or death.

Read and understand this material before

operating or servicing this equipment. Failure to

understand how to safely operate this tool could

result in an accident causing serious injury or

death.

This symbol is used to call your attention to hazards or unsafe

practices which could result in an injury or property damage. The

signal word, defined below, indicates the severity of the hazard. The

message after the signal word provides information for preventing or

avoiding the hazard.

SAFETY ALERT SYMBOL

Immediate hazards which, if not avoided, WILL result in severe injury

or death.

Hazards which, if not avoided, COULD result in severe injury or death.

Hazards or unsafe practices which, if not avoided, MAY result in injury

or property damage.

4

Important Safety Information

Electric shock and fire hazard:

• Do not expose this unit to rain or moisture.

• Do not use the unit if it is wet or damaged.

• Use this unit for the manufacturer’s intended purpose only, as

described in this manual. Any other use can impair the protection

provided by the unit.

Failure to observe these warnings could result in severe injury or death.

Electric shock hazard:

• Do not operate with the case or battery door open.

• Before opening the case or battery door, remove the test leads

(or jaw) from the circuit and shut off the unit.

Failure to observe these warnings could result in severe injury or death.

Electric shock hazard:

• Using this unit near equipment that generates electromagnetic

interference can result in unstable or inaccurate readings.

• Unless measuring voltage or current, shut off and lock out power.

Make sure that all capacitors are discharged. Voltage must not be

present.

Failure to observe these warnings could result in severe injury or death.

5

CM-410

Electric shock hazard:

• Do not attempt to repair this unit. It contains no user-serviceable

parts.

• Do not expose the unit to extremes in temperature or high humidity.

Refer to “Specifications.”

Failure to observe these precautions may result in injury and can

damage the unit.

Important Safety Information

Electric shock hazard:

Do not change the measurement function while the test leads are

connected to a component or circuit.

Failure to observe this precaution may result in injury and can damage

the unit.

6

Identification

1. Jaw

2. Lever

3. Selector switch

4. Display

5. Negative, common (COM), or

ground input terminal

6. Volts or resistance (V-Ω) input

terminal

7. Select/toggle button

8. Hold button

910111213141516

17

18

19

20

21

1

3

4

5

2

8

7

6

Symbols on the Unit

Warning—Read the instruction manual

Risk of electric shock

Double insulation

Battery

Recycle product in accordance with manufacturer’s directions

Display Icons

9. Hold function is enabled.

10. A Amps

11. V Volts

12. Ω Ohms

13. k kilo (10

3

)

14. M Mega (10

6

)

15. Continuity mode

16. Auto ranging is enabled.

17. AC measurement is selected.

18. – Negative polarity indicator

19. DC measurement is selected.

20. Low battery indicator

21.

O.L

Overload indicator

7

CM-410

Using the Features

• Selector Switch

Slide switch to desired mode of operation:

(amps)

(AC/DC voltage)

(ohms/continuity)

Return switch to OFF position when not in use.

• Select/Toggle Button

Momentarily press button to select AC or DC voltage, ohms, or

continuity mode.

• Hold Button

Press momentarily to hold the present value on the display.

will

appear on the display.

Press again to return to normal mode.

• Auto Power Off

The unit automatically shuts off after approximately 10 minutes of

inactivity.

8

Operation

1. Set the selector switch according to the Settings Table. Momentarily

press the select/toggle button to select mode.

2. Refer to “Typical Measurements” for specific measurement

instructions.

3. Test the unit on a known functioning circuit or component.

• If the unit does not function as expected on a known functioning

circuit, replace the battery.

• If the unit still does not function as expected, send the unit to

Greenlee for repair. Refer to the instructions under the Warranty.

4. Take the reading from the circuit or component to be tested.

Settings Table

Electric shock hazard:

Contact with live circuits could result in severe

injury or death.

To measure

this value …

Connect

red lead

to …

Connect

black lead

to …

Momentarily press

the Select/Toggle

Button until this

icon appears

on the display …

Set the

Selector Switch

to this

symbol …

AC Amps* N/A N/AN/A

AC Voltage V-Ω COM

DC Voltage V-Ω COM

Continuity** V-Ω COM

Resistance V-Ω COM

M Ω

*AC Amp measurements are made using the jaw clamp. Refer to “Typical

Measurements” for specific measurement instructions.

**Tone indicates a circuit resistance of less than 20 Ω.

9

CM-410

Typical Measurements

Clamp Around Line Splitter

Notes:

• The Greenlee 93-30 Line Splitter is

divided. One section renders amps; the

other renders amps multiplied by 10.

• Close the jaw completely to ensure

accurate measurement.

• Center the line splitter in the jaw for

highest accuracy.

Clamp Around Wire

Notes:

• Clamp the jaw around one

conductor only.

• Close the jaw completely to

ensure accurate measurement.

• Center the wire in the jaw for

highest accuracy.

AC Amps

10

Typical Measurements

Voltage

11

CM-410

Typical Measurements

Resistance

Continuity

12

Accuracy

Refer to “Specifications” for operating conditions and temperature

coefficient.

Accuracy is specified as follows: ± (a percentage of the reading + a fixed

amount) at 23 °C ± 5 °C (73.4 °F ± 9 °F), 0% to 80% relative humidity.

Amps

Measurement Frequency

Range Accuracy Range

0.0 to 40.0 A ± (1.9% + 1 A) 50 to 60 Hz

40.0 to 200.0 A ± (1.9% + 0.5 A) 50 to 60 Hz

201 to 400 A ± (1.9% + 5 A) 50 to 60 Hz

AC Voltage

Measurement Frequency Input

Range Accuracy Range Impedance

200.0 V ± (1.5% + 0.5 V) 50 to 500 Hz

10 MΩ //

600 V ± (1.5% + 5 V) 50 to 500 Hz

100 pF max

DC Voltage

Measurement Input

Range Accuracy Impedance

200.0 V ± (1.0% + 0.2 V)

10 MΩ //

600 V ± (1.0% + 2 V)

100 pF max

Resistance

Measurement

Range Accuracy

200.0 Ω± (1.2% + 0.5 Ω)

2.000 kΩ± (0.7% + 0.002 kΩ)

20.00 kΩ± (0.7% + 0.02 kΩ)

200.0 kΩ± (0.7% + 0.2 kΩ)

2.000 MΩ± (1.0% + 0.002 MΩ)

20.00 MΩ± (1.9% + 0.05 MΩ)

13

CM-410

Specifications

Display: 3-1/2-digit LCD (1999 maximum reading)

Sampling Rate: 1.5 per second

Overrange Indication: “OL” appears on the display

Jaw Opening: 30 mm (1.18")

Maximum Conductor Diameter: 27 mm (1.06")

Measurement Category: Category III, 600 V

Temperature Coefficient: 0.2 x (specified accuracy) per °C

below 18 °C or above 28 °C

Operating Conditions:

At 0% ≤ 80% RH: 0 °C to 30 °C (32 °F to 86 °F)

At 0% ≤ 75% RH: 30 °C to 40 °C (86 °F to 104 °F)

At 0% ≤ 45% RH: 40 °C to 50 °C (104 °F to 122 °F)

Altitude: 2000 m (6500') maximum

Indoor use only

Storage Conditions: -20 °C to 60 °C (-4 °F to 140° F),

0% to 80% relative humidity with battery removed

Pollution Degree: 2

Battery: Two 1.5 V (AAA, A4M, or IEC LR03)

14

Measurement Categories

These definitions were derived from the international safety standard for

insulation coordination as it applies to measurement, control, and

laboratory equipment. These measurement categories are explained in

more detail by the International Electrotechnical Commission; refer to

either of their publications: IEC 61010-1 or IEC 60664.

Measurement Category I

Signal level. Electronic and telecommunication equipment, or parts thereof.

Some examples include transient-protected electronic circuits inside

photocopiers and modems.

Measurement Category II

Local level. Appliances, portable equipment, and the circuits they are

plugged into. Some examples include light fixtures, televisions, and long

branch circuits.

Measurement Category III

Distribution level. Permanently installed machines and the circuits they are

hard-wired to. Some examples include conveyor systems and the main

circuit breaker panels of a building’s electrical system.

Measurement Category IV

Primary supply level. Overhead lines and other cable systems. Some

examples include cables, meters, transformers, and other exterior

equipment owned by the power utility.

Statement of Conformity

Greenlee Tools, Inc. is certified in accordance with ISO 9000 (2000) for

our Quality Management Systems.

The instrument enclosed has been checked and/or calibrated using

equipment that is traceable to the National Institute for Standards and

Technology (NIST).

15

CM-410

Maintenance

Electric shock hazard:

• Do not attempt to repair this unit. It contains no user-serviceable

parts.

• Do not expose the unit to extremes in temperature or high humidity.

Refer to “Specifications.”

Failure to observe these precautions may result in injury and can

damage the unit.

Battery Replacement

Electric shock hazard:

• Do not operate with the case or battery door open.

• Before opening the case or battery door, remove the test leads

(or jaw) from the circuit and shut off the unit.

Failure to observe these warnings could result in severe injury or death.

1. Disconnect the unit from the circuit. Turn the unit OFF.

2. Remove the screw from the battery door.

3. Remove the battery door.

4. Replace the batteries (observe polarity).

5. Replace the battery door and the screw.

Cleaning

Periodically wipe the case with a damp cloth and mild detergent; do not

use abrasives or solvents.

16

17

CM-410

Descripción

El Medidor digital con pinza modelo CM-410 de Greenlee es un

instrumento de verificación capaz de medir hasta 400 amperios de

corriente alterna, además de medir tensión alterna o continua, resistencia y

verificar continuidad. Esta unidad es de bolsillo y cabe perfectamente en la

palma de la mano.

Acerca de la seguridad

Es fundamental observar métodos seguros al utilizar y dar mantenimiento

a las herramientas y equipo Greenlee. Este manual de instrucciones y todas

las marcas que ostenta la herramienta le ofrecen la información necesaria

para evitar riesgos y hábitos poco seguros relacionados con su uso. Siga

toda la información sobre seguridad que se proporciona.

Propósito de este manual

Este manual de instrucciones tiene como propósito familiarizar a todo el

personal con los procedimientos de operación y mantenimiento seguros

para el Medidor digital con pinza, modelo CM-410 de Greenlee.

Manténgalo siempre al alcance de todo el personal.

Puede obtener copias adicionales de manera gratuita, previa solicitud:

www.greenlee.com.

CONSERVE ESTE MANUAL

Todas las especificaciones son nominales y pueden cambiar conforme tengan lugar

mejoras de diseño. Greenlee

Tools

, Inc. no se hace responsable de los daños que

puedan surgir de la mala aplicación o mal uso de sus productos.

® Registrado: El color verde para instrumentos de verificación eléctricos es una marca

registrada de Greenlee

Tools

, Inc.

¡No deseche ni descarte este producto!

Para información sobre reciclaje, visite www.greenlee.com.

18

Importante Información sobre Seguridad

Peligro de electrocución:

El contacto con circuitos activados podría

ocasionar graves lesiones o incluso la muerte.

Lea y entienda este documento antes de

manejar esta herramienta o darle mantenimiento.

Utilizarla sin comprender cómo manejarla de

manera segura podría ocasionar un accidente y,

como resultado de éste, graves lesiones o

incluso la muerte.

Este símbolo se utiliza para indicar un riesgo o práctica poco segura

que podría ocasionar lesiones o daños materiales. Cada uno de los

siguientes términos denota la gravedad del riesgo. El mensaje que

sigue a dichos términos le indica cómo puede evitar o prevenir ese

riesgo.

SÍMBOLO DE ALERTA

SOBRE SEGURIDAD

Peligros inmediatos que, de no evitarse, OCASIONARÁN graves

lesiones o incluso la muerte.

Peligros que, de no evitarse, PODRÍAN OCASIONAR graves lesiones o

incluso la muerte.

Peligro o prácticas peligrosas que, de no evitarse, PUEDEN

OCASIONAR lesiones o daños materiales.

19

CM-410

Importante Información sobre Seguridad

Peligro de electrocución:

• No haga funcionar esta unidad con la caja o la puerta del

compartimiento de las baterías abierta.

• Antes de abrir la caja o la puerta del compartimiento de las baterías,

retire del circuito los cables de prueba (o la pinza), y apague la

unidad.

De no observarse estas advertencias podrían sufrirse graves lesiones o

incluso la muerte.

Peligro de electrocución e incendio:

• No exponga esta unidad ni a la lluvia ni a la humedad.

• No utilice esta unidad si se encuentra mojada o dañada.

• Utilícela únicamente para el propósito para el que ha sido diseñada

por el fabricante, tal como se describe en este manual. Cualquier

otro uso puede menoscabar la protección proporcionada por la

unidad.

De no observarse estas advertencias podrían sufrirse graves lesiones o

incluso la muerte.

Peligro de electrocución:

• Al utilizar esta unidad cerca de equipo que genere interferencia

electromagnética quizá se obtenga una lectura inexacta e inestable.

• A menos que vaya a medir tensión o corriente, apague y bloquee la

energía. Asegúrese que todos los condensadores estén totalmente

sin carga. No debe haber tensión alguna.

De no observarse estas advertencias podrían sufrirse graves lesiones o

incluso la muerte.

20

Importante Información sobre Seguridad

Peligro de electrocución:

No cambie la función de medición mientras los cables de prueba estén

conectados a un componente o circuito.

De no observarse esta advertencia podrían sufrirse lesiones o daños a

la unidad.

Peligro de electrocución:

• No intente reparar esta unidad, ya que contiene partes que deben

recibir mantenimiento por parte de un profesional.

• No exponga la unidad a ambientes de temperatura extrema o altos

niveles de humedad. Consulte la sección “Especificaciones”.

De no observarse estas precauciones podrían sufrirse lesiones o daños

a la unidad.

La page charge ...

Greenlee CM-410 Digital Clamp-on Meter Manual Manuel utilisateur

Ce manuel convient également à

Greenlee CM-410 Digital Clamp-on Meter Manual Manuel utilisateur

dans d''autres langues

Documents connexes