RIDGID micro CA-100 Manuel utilisateur

RIDGE TOOL COMPANY

p. 1

p. 13

p. 25

p. 37

p. 49

p. 61

p. 73

p. 85

p. 97

p. 109

p. 121

p. 133

p. 145

p. 157

p. 169

p. 181

p. 193

p. 207

p. 219

p. 231

p. 243

p. 257

EN

FR

ES

DE

NL

IT

PT

SV

DA

NO

FI

PL

CZ

SK

RO

HU

EL

HR

SL

SR

RU

TR

micro

CA-100

micro CA-100

micro CA-100 Inspection Camera

Record Serial Number below and retain product serial number which is located on nameplate.

Serial

No.

micro CA-100

Inspection Camera

WARNING!

Read this Operator’s Man-

ual carefully before using

this tool. Failure to under-

stand and follow the con-

tents of this manual may

result in electrical shock,

ﬁre and/or serious per-

sonal injury.

micro CA-100 Inspection Camera

2

Table of Contents

Safety Symbols ...............................................................................................................................3

General Safety Information

Work Area Safety ..................................................................................................................................3

Electrical Safety .....................................................................................................................................3

Personal Safety ......................................................................................................................................3

Equipment Use and Care ..................................................................................................................4

Service ......................................................................................................................................................4

Speciﬁc Safety Information

micro CA-100 Inspection Camera Safety ...................................................................................4

Description, Speciﬁcations and Standard Equipment

Description .............................................................................................................................................5

Speciﬁcations ........................................................................................................................................5

Standard Equipment ..........................................................................................................................5

Controls ....................................................................................................................................................6

FCC Statement ................................................................................................................................6

Electromagnetic Compatibility (EMC) ...............................................................................6

Tool Assembly

Changing/Installing Batteries .........................................................................................................6

Installing Imager Head Cable or Extension Cables ................................................................7

Installing An Accessory ......................................................................................................................7

Pre-Operation Inspection.........................................................................................................7

Tool and Work Area Set-Up ......................................................................................................8

Operating Instructions ..............................................................................................................9

Viewing ....................................................................................................................................................9

Maintenance

Cleaning ................................................................................................................................................10

Reset Function ...................................................................................................................................10

Accessories .................................................................................................................................... 10

Storage ............................................................................................................................................ 10

Service and Repair..................................................................................................................... 10

Disposal ........................................................................................................................................... 11

Battery Disposal ......................................................................................................................... 11

Troubleshooting ......................................................................................................................... 11

Lifetime Warranty ......................................................................................................Back Cover

*Original instructions - English

micro CA-100 Inspection Camera

3

Safety Symbols

In this operator’s manual and on the product, safety symbols and signal words are used to

communicate important safety information. This section is provided to improve understand-

ing of these signal words and symbols.

This is the safety alert symbol. It is used to alert you to potential personal injury hazards.

Obey all safety messages that follow this symbol to avoid possible injury or death.

DANGER

WARNING

CAUTION

NO TICE

DANGER indicates a hazardous situation which, if not avoided, will result in death

or serious injury.

WARNING indicates a hazardous situation which, if not avoided, could result in

death or serious injury.

CAUTION indicates a hazardous situation which, if not avoided, could result in

minor or moderate injury.

NOTICE indicates information that relates to the protection of property.

This symbol means read the operator’s manual carefully before using the equipment.

The operator’s manual contains important information on the safe and proper operation

of the equipment.

This symbol means always wear safety glasses with side shields or goggles when han-

dling or using this equipment to reduce the risk of eye injury.

This symbol indicates the risk of hands, ﬁngers or other body parts being caught or

wrapped in gears or other moving parts.

This symbol indicates the risk of electrical shock.

General Safety

Information

WARNING

Read all safety warnings and instructions.

Failure to follow the warnings and instruc-

tions may result in electric shock, ﬁre and/

or serious injury.

SAVE THESE INSTRUCTIONS!

The CE declaration of conformity (890-011-

320) will accompany this manual as a sepa-

rate booklet when required.

Work Area Safety

 • Keep your work area clean and well lit.

Cluttered or dark areas invite accidents.

 • Do not operate equipment in ex-

plosive atmospheres, such as in the

presence of ﬂammable liquids, gases

or dust. Equipment can create sparks

which may ignite the dust or fumes.

 • Keep children and by-standers away

while operating equipment. Distrac-

tions can cause you to lose control.

Electrical Safety

 • Avoid body contact with earthed or

grounded surfaces such as pipes, radi-

ators, ranges and refrigerators. There

is an increased risk of electrical shock if

your body is earthed or grounded.

 • Do not expose equipment to rain or

wet conditions. Water entering equip-

ment will increase the risk of electrical

shock.

Personal Safety

 • Stay alert, watch what you are doing

and use common sense when operat-

ing equipment. Do not use equipment

while you are tired or under the inﬂu-

ence of drugs, alcohol or medication.

A moment of inattention while operat-

ing equipment may result in serious per-

sonal injury.

 • Do not overreach. Keep proper foot-

ing and balance at all times. This en-

ables better control of the power tool in

unexpected situations.

micro CA-100 Inspection Camera

4

 • Use personal protective equipment.

Always wear eye protection. Protective

equipment such as dust mask, non-skid

safety shoes, hard hat or hearing protec-

tion used for appropriate conditions will

reduce personal injuries.

Equipment Use and Care

 • Do not force equipment. Use the cor-

rect equipment for your application.

The correct equipment will do the job

better and safer at the rate for which it is

designed.

 • Do not use equipment if the switch

does not turn it ON and OFF. Any tool

that cannot be controlled with the switch

is dangerous and must be repaired.

 • Disconnect the batteries from the

equipment before making any adjust-

ments, changing accessories, or stor-

ing. Such preventive safety measures

reduce the risk of injury.

 • Store idle equipment out of the reach

of children and do not allow per-

sons unfamiliar with the equipment

or these instructions to operate the

equipment. Equipment can be danger-

ous in the hands of untrained users.

 • Maintain equipment. Check for mis-

alignment or binding of moving parts,

missing parts, breakage of parts and

any other condition that may aﬀect the

equipment’s operation. If damaged,

have the equipment repaired before use.

Many accidents are caused by poorly

maintained equipment.

 • Use the equipment and accessories in

accordance with these instructions,

taking into account the working con-

ditions and the work to be performed.

Use of the equipment for operations dif-

ferent from those intended could result

in a hazardous situation.

 • Use only accessories that are recom-

mended by the manufacturer for

your equipment. Accessories that may

be suitable for one piece of equipment

may become hazardous when used with

other equipment.

 • Keep handles dry and clean; free from

oil and grease. Allows for better control

of the equipment.

Service

 • Have your equipment serviced by a

qualiﬁed repair person using only

identical replacement parts. This will

ensure that the safety of the tool is main-

tained.

Specific Safety Information

WARNING

This section contains important safety in-

formation that is speciﬁc to the inspection

camera.

Read these precautions carefully before us-

ing the micro CA-100 Inspection Camera to

reduce the risk of electrical shock or other

serious injury.

SAVE THESE INSTRUCTIONS!

A manual holder is supplied in the carrying

case of the micro CA-100 Inspection Camera

to keep this manual with the tool for use by

the operator.

micro CA-100 Inspection Camera

Safety

 • The micro CA-100 imager head and

cable are waterproof to 10’. The hand-

held display unit is not. Do not expose

the display unit to water or rain. This in-

creases the risk of electrical shock.

 • Do not place the micro CA-100 In-

spection Camera anywhere that may

contain a live electrical charge. This

increases the risk of electrical shock.

 • Do not place the micro CA-100 Inspec-

tion Camera anywhere that may con-

tain moving parts. This increases the

risk of entanglement injuries.

 • Do not use this device for personal

inspection or medical use in any way.

This is not a medical device. This could

cause personal injury.

 • Always use appropriate personal pro-

tective equipment while handling and

using the micro CA-100 Inspection

Camera. Drains and other areas may

contain chemicals, bacteria and other

substances that may be toxic, infectious,

cause burns or other issues. Appropri-

ate personal protective equipment

always includes safety glasses and

gloves, and may include equipment

such as latex or rubber gloves, face

micro CA-100 Inspection Camera

5

shields, goggles, protective clothing, res-

pirators and steel-toed footwear.

 • Practice good hygiene. Use hot, soapy

water to wash hands and other exposed

body parts exposed to drain contents af-

ter handling or using the micro CA-100

Inspection Camera to inspect drains and

other areas that may contain chemicals

or bacteria. Do not eat or smoke while

operating or handling the micro CA-100

Inspection Camera. This will help prevent

contamination with toxic or infectious

material.

 • Do not operate the micro CA-100 In-

spection Camera if operator or device

is standing in water. Operating an elec-

trical device while in water increases the

risk of electrical shock.

The EC Declaration of conformity (890-011-

320.10) will accompany this manual as a

separate booklet when required.

If you have any question concerning this

RIDGID® product:

– Contact your local RIDGID distributor.

– Visit www.RIDGID.com or

www.RIDGID.eu to ﬁnd your local

RIDGID contact point.

– Contact RIDGID Technical Services De-

partment at rtctechservices@emerson.

com, or in the U.S. and Canada call (800)

519-3456.

Description, Specifications

and Standard Equipment

Description

The micro CA-100 Inspection Camera dis-

plays live color video from an imaging sen-

sor and light source that’s connected to a

3’ ﬂexible cable. It can be used to look into

tight spots and beam back real-time video

to a color LCD. It comes with a 17 mm (3/4”)

camera head for general use.

Standard Equipment

The micro CA-100 Inspection Camera comes

with the following items:

• microCA-100

• 17mmImager

• 3’RCACable

• Hook,Magnet,MirrorAttachments

• 4x“AA”Batteries

Specifications

Display................................. 3,5” Color LCD

(320 x 240 Resolu-

tion)

Lighting................................ 4 Adjustable LEDs

Cable Reach....................... 3’ (Expandable to

30’ with Optional

Extensions) Water-

proof to 10’ (IP67)

Camera Head..................... 17 mm (3/4”)

Video Output.................... RCA (3’ Cable

Included)

TV-Out................................. PAL/NTSC

Operating Temp............... 0°C ~ 50°C

Storage Temp.................... -20°C ~ 60°C

Storage Humidity............ 15% ~ 85% RH

Depth of Field (DOF)...... 10mm~•(inn-

ity)

Power Source.................... 4x“AA”,Alkaline

or Rechargeable

Attachments..................... Hook, Magnet,

Mirror

Weight................................ 2,5 kg (5,5 lbs)

Figure 1 - micro CA-100

micro CA-100 Inspection Camera

6

Controls

FCC Statement

This equipment has been tested and found

to comply with the limits for a Class B digital

device, pursuant to part 15 of the FCC Rules.

These limits are designed to provide reason-

able protection against harmful interference

in a residential installation.

This equipment generates, uses, and can

radiate radio frequency energy and, if not

installed and used in accordance with the

instructions, may cause harmful interference

to radio communications.

However, there is no guarantee that interfer-

ence will not occur in a particular installa-

tion.

If this equipment does cause harmful in-

terference to radio or television reception,

which can be determined by turning the

equipment OFF and ON, the user is encour-

aged to try to correct the interference by one

or more of the following measures:

 • Reorientorrelocatethereceivinganten-

na.

 • Increase the separation between the

equipment and receiver.

 • Consultthedealeroranexperiencedra-

dio/TV technician for help.

Electromagnetic

Compatibility (EMC)

The term electromagnetic compatibility is

taken to mean the capability of the prod-

uct to function smoothly in an environment

where electromagnetic radiation and elec-

Battery

Indicator

Power

LED Brightness

Increase

Rotate

Image

LED Brightness

Decrease

Figure 2 - Controls

trostatic discharges are present and without

causing electromagnet interference to other

equipment.

NO TICE

The RIDGID micro CA-100 Inspec-

tion Camera conforms to all applicable EMC

standards. However, the possibility of it caus-

ing interference in other devices cannot be

precluded.

Tool Assembly

WARNING

To reduce the risk of serious injury during

use, follow these procedures for proper as-

sembly.

Changing/Installing Batteries

The micro CA-100 is supplied without batter-

ies installed. If the battery indicator displays

red

, the batteries need to be replaced.

Remove the batteries prior to long term stor-

age to avoid battery leakage.

1. Squeeze the battery clips (See Figure 3)

and remove battery compartment from

the micro CA-100 Inspection Camera

(See Figure 4). If needed, remove batter-

ies.

2. Install 4 new AA alkaline batteries (LR6),

observing the correct polarity as indi-

cated on the battery compartment. Only

replace in sets to help prevent battery

leakage.

3. Squeeze the clips and ﬁrmly insert into

inspection camera. The holder will only

go in one way. Do not force. Conﬁrm se-

curely attached.

Figure 3 - Battery Compartment Cover

micro CA-100 Inspection Camera

7

Installing the Imager Head Cable

or Extension Cables

To use the micro CA-100 Inspection Camera,

the imager head cable must be connected

to the handheld display unit. To connect the

cable to the handheld display unit, make

sure the key and slot (Figure 5) are properly

aligned. Once they are aligned, ﬁnger tight-

en the knurled knob to hold the connection

in place.

3’ and 6’ cable extensions are available to in-

crease the length of your cable up to 30’ in

length. To install an extension, ﬁrst remove

the camera head cable from the display unit

by loosening the knurled knob. Connect

the extension to the handheld as described

above (Figure 5). Connect the keyed end of

the camera head cable to the slotted end of

the extension and ﬁnger tighten the knurled

knob to hold the connection in place.

Installing An Accessory

The three included accessories, (mirror, hook

and magnet) (Figure 1) all attach to the im-

ager head the same way.

To connect, hold the imager head as shown

in Figure 6. Slip the semicircle end of the ac-

cessory over the ﬂats of the imager head as

shown in Figure 6. Then rotate the accessory

a 1/4 turn so the long arm of the accessory is

extending out as shown (Figure 6).

Slot Key

Figure 5 - Cable Connections

Pre-Operation Inspection

WARNING

Before each use, inspect your inspection

camera and correct any problems to reduce

the risk of serious injury from electric shock

and other causes and prevent tool damage.

1. Make sure the unit is OFF.

2. Remove the battery holder and inspect

it and batteries for signs of damage. Re-

place batteries if necessary. Do not use

inspection camera if batteries are dam-

aged.

3. Clean any oil, grease or dirt from the

equipment. This aids inspection and

helps prevent the tool from slipping

from your grip.

4. Inspect micro CA-100 Inspection Camera

for any broken, warn, missing, misaligned

or binding parts or any condition which

may prevent safe and normal operation.

5. Inspect the camera head lens for con-

densation. To avoid damaging the unit,

do not use the camera if condensation

forms inside the lens. Let the water evap-

orate before using.

6. Inspect the full length of the cable for

cracks or damage. A damaged cable

could allow water to enter the unit and

increase the risk of electrical shock.

7. Check to make sure the connections be-

tween the handheld unit, extension ca-

bles and imager cable are tight. All con-

nections must be properly assembled for

the cable to be water resistant. Conﬁrm

unit is properly assembled.

Accessory

Figure 6

Figure 4 - Battery Compartment

micro CA-100 Inspection Camera

8

8. Check that the warning label is present,

ﬁrmly attached and readable.

9. If any issues are found during the inspec-

tion, do not use the inspection camera

until it has been properly serviced.

10. With dry hands, re-install the battery

holder making sure to fully insert.

11. Press and Hold the Power Button for 3

seconds. A splash screen will appear.

Once the camera is ready an image will

appear. Consult the Troubleshooting sec-

tion of this manual if problems arise.

12. Press and Hold the Power Button for 3

seconds to turn the unit OFF.

Tool and Work Area Set-Up

WARNING

Set up the micro CA-100 Inspection Cam-

era and work area according to these pro-

cedures to reduce the risk of injury from

electrical shock, entanglement and other

causes and prevent tool and system dam-

age.

1. Check work area for:

 • Adequatelighting.

 • Flammableliquids,vaporsordustthat

may ignite. If present, do not work in

area until sources have been identi-

ﬁed and corrected. The micro CA-100

Inspection Camera is not explosion

proof and can cause sparks.

Figure 7 - Warning Label

 • Clear,level,stable,dryplaceforopera-

tor. Do not use the inspection camera

while standing in water.

2. Examine the area or space that you will

be inspecting and determine if the micro

CA-100 Inspection Camera is the correct

piece of equipment for the job.

 • Determine the access points to the

space. The minimum opening the

camera head can ﬁt through is approx-

imately 3/4” in diameter for the 17 mm

camera head.

 • Determinethedistancetotheareato

be inspected. Extensions can be added

to the camera to reach up to 30’.

 • Determine if there are any obstacles

that would require very tight turns in

the cable. The inspection camera cable

can go down to a 50 mm (2” ) radius

without damage.

 • Determine if there is any electrical

power supplied to the area to be in-

spected. If so, the power to the area

must be turned oﬀ to reduce the risk

of electric shock. Use appropriate lock

out procedures to prevent the power

from being turned back on during the

inspection.

 • Determine if any liquids will be en-

countered during the inspection. The

cable and imager head are waterproof

to a depth of 10’. Greater depths may

cause leakage into the cable and imag-

er and cause electric shock or damage

the equipment. The handheld display

unit is not water resistant and should

not be exposed to wet conditions.

 • Determine if any chemicals are pres-

ent, especially in the case of drains. It

is important to understand the spe-

ciﬁc safety measures required to work

around any chemicals present. Con-

tact the chemical manufacturer for

required information. Chemicals may

damage or degrade the inspection

camera.

 • Determinethetemperatureofthearea

and items in the area. The working

temperature of the inspection cam-

era is between 0°C -50°C (32 and 122

degrees F). Use in areas outside of this

range or contact with hotter or colder

items could cause camera damage.

 • Determine if any moving parts are

present in the area to be inspected. If

so, these parts must be deactivated to

micro CA-100 Inspection Camera

9

prevent movement during inspection

to reduce the risk of entanglement.

Use appropriate lock out procedures

to prevent the parts from moving dur-

ing the inspection.

If the micro CA-100 Inspection Camera is

not the correct piece of equipment for the

job, other inspection equipment is available

from RIDGID. For a complete listing of RIDGID

products, see the RIDGID catalog, online at

www.RIDGID.com or www.RIDGID.eu.

3. Make sure the micro CA-100 Inspection

Camera has been properly inspected be-

fore each use.

4. Install the correct accessories for the ap-

plication.

Operating Instructions

WARNING

Always wear eye protection to protect your

eyes against dirt and other foreign objects.

Follow operating instructions to reduce the

risk of injury from electrical shock, entan-

glement and other causes.

1. Make sure that the inspection camera

and work area have been properly set

up and that the work area is free of by-

standers and other distractions.

Figure 8 - Controls

Rotate

Image

LED Brightness

Decrease

Battery

Indicator

Power

LED Brightness

Increase

2. Power On: Press and Hold the power

button for 3 seconds.

The power status light will come ON. If

the power status light is GREEN, the mi-

cro CA-100 Inspection Camera batteries

are good. If the power status light is RED,

the batteries need to be changed. If the

LED does not turn ON, the batteries need

to be changed or the unit needs service.

The splash screen will appear.

3. Pre-Form The Cable: If needed for the

area to be inspected, pre-form the cable.

Do not try to form bends with a radius of

less than 2”, this can damage the cable.

4. LED Brightness Adjustment: Turn the

LEDs ON. The imager head is equipped

with four white LEDs to aid inspection.

Use the + and – buttons to turn ON and

adjust the brightness of the LEDs.

5. Inspection: Insert the imager head and

cable into the space to be inspected. Do

not use the imager head or cable for any-

thing other than an inspection device.

Do not use the imager head and cable

to clear a path. Do not force the imager

head and cable through tight bends or

spaces. These uses can damage the unit

and the area to be inspected.

6. Image Rotation: If needed, the image

seen on the screen can be rotated in 90

degree increments counter clockwise by

pressing the rotate image button.

7. Power Oﬀ: When the inspection is com-

plete, carefully withdraw the imager and

cable from the inspection area. Press and

Hold the power button for 1 second to

turn the unit OFF. The unit will automati-

cally turn OFF 30 minutes after the last

button press or if the batteries drop too

low.

Viewing

The micro CA-100 Inspection Camera can be

connected to a television or other monitor

for remote viewing or recording through the

included RCA cable. Open the rubber cover

on the side of the grip and insert the RCA

cable into the TV-OUT jack.

Insert the other end into the Video In jack

on the television or monitor. The television

or monitor may need to be set to the proper

input to allow viewing.

micro CA-100 Inspection Camera

10

Maintenance

WARNING

Remove batteries before cleaning.

Cleaning

 • Alwayscleantheimagerheadandcable

after use with mild soap or mild deter-

gent.

 •Gently clean the LCD with a clean dry

cloth. Avoid rubbing too hard on the

LCD.

 • Useonlyalcoholswabstocleantheca-

ble connections.

 • Wipe the hand held display unit down

with a clean, dry cloth.

Reset Function

If the unit stops functioning and does not

operate, press the Reset Button. (See Figure

9). The unit may recover to normal operation

when restarted.

Accessories

WARNING

To reduce the risk of serious injury, only use

accessories speciﬁcally designed and rec-

ommended for use with the RIDGID micro

CA-100 Inspection Camera such as those

listed below. Other Accessories suitable

for use with other tools may be hazardous

when used with the micro CA-100 Inspec-

tion Camera.

Figure 9 - TV-OUT Jack/Reset Button

Storage

The RIDGID micro CA-100 Inspection Camera

must be stored in a dry secure area between

-20°C (-4°F) and 60°C (140°F).

Store the tool in a locked area out of the

reach of children and people unfamiliar with

the micro CA-100 Inspection Camera.

Remove the batteries before any long period

of storage or shipping to avoid battery leak-

age.

Service and Repair

WARNING

Improper service or repair can make the

RIDGID micro CA-100 Inspection Camera un-

safe to operate.

Service and repair of the micro CA-100 In

spection Camera must be performed by a

RIDGID Independent Authorized Service

Center.

For information on your nearest RIDGID In-

dependent Service Center or any service or

repair questions:

 •ContactyourlocalRIDGIDdistributor.

 •Visitwww.RIDGID.comor

www.RIDGID.eu to ﬁnd your local

RIDGID contact point.

 •Contact RIDGID Technical Services De-

partment at rtctechservices@emerson.

com, or in the U.S. and Canada call (800)

519-3456.

Catalog

No.

Description

31128 3’ Cable Extension

31133 6’ Cable Extension

37103 Imager Head and Cable - 17 mm

(*List subject to change.)

micro CA-100 Inspection Camera

Accessories*

micro CA-100 Inspection Camera

11

Troubleshooting

SYMPTOM POSSIBLE REASON SOLUTION

Display turns ON, but does not

show image.

Loose cable connections. Check cable connections, clean if re-

quired. Re-attach.

Imager is broken. Replace batteries.

LEDs on imager head are dim at

max brightness, display switches

between black and white, color

display turns itself OFF after a

brief period.

Battery low on power. Replace the Imager.

Unit will not turn ON. Dead batteries. Unit need to be reset.

Replace batteries. Reset unit. See “Maintenance” Sec-

tion.

Disposal

Parts of the RIDGID micro CA-100 Inspection

Camera contain valuable materials and can

be recycled. There are companies that spe-

cialize in recycling that may be found locally.

Dispose of the components in compliance

with all applicable regulations. Contact your

local waste management authority for more

information.

For EC Countries: Do not dis-

pose of electrical equipment with

household waste!

According to the European Guide-

line 2002/96/EC for Waste Electri-

cal and Electronic Equipment an-

dits implementation into national legislation,

electrical equipment that is no longer usable

must be collected separately and disposed

of in an environmentally correct manner.

Battery Disposal

For EC countries: Defective or used batteries

must be recycled according to the guideline

2006/66/EEC.

micro CA-100 Inspection Camera

12

Caméra d’inspection

micro CA-100

microCA-100

AVERTISSEMENT

Familiarisez-vous bien avec le

mode d’emploi avant d’utiliser

l’appareil. L’incompréhension

ou le non-respect des consignes

ci-après augmenteraient les

risques de choc électrique, d’in-

cendie et/ou d’accident grave.

Caméra d’inspection micro CA-100

Notez ci-dessous le numéro de série inscrit sur la plaque signalétique de l’appareil pour future référence.

Nº de

série

14

Caméra d’inspection micro CA-100

Table des matières

Symboles de sécurité ........................................................................................15

Consignes générales de sécurité

Sécurité des lieux ............................................................................................15

Sécurité électrique ...........................................................................................15

Sécurité individuelle.........................................................................................15

Utilisation et entretien du matériel ...................................................................16

Service après-vente.........................................................................................16

Consignes de sécurité spécifiques

Sécurité de la caméra dʼinspection micro CA-100...........................................16

Description, caractéristiques techniques et équipements de base

Description.......................................................................................................17

Caractéristiques techniques ............................................................................17

Equipements de base ......................................................................................18

Commandes ....................................................................................................18

Déclaration FCC .................................................................................................18

Compatibilité électromagnétique (EMC)..........................................................18

Assemblage de lʼappareil

Remplacement des piles .................................................................................18

Installation du câble de tête de caméra et de ses rallonges............................19

Montage des accessoires ................................................................................19

Contrôle préalable .............................................................................................19

Préparation de lʼappareil et des lieux ..............................................................20

Consignes dʼutilisation .....................................................................................21

Visualisation.....................................................................................................22

Entretien

Nettoyage ........................................................................................................22

Remise à zéro..................................................................................................23

Accessoires........................................................................................................23

Stockage .............................................................................................................23

Révisions et réparations ...................................................................................23

Recyclage ...........................................................................................................23

Recyclage des piles...........................................................................................23

Dépannage..........................................................................................................24

Garantie à vie..................................................................................Page de garde

*Traduction de la notice originale

Caméra d’inspection micro CA-100

15

Symboles de sécurité

Des symboles et mots clés spécifiques, utilisés à la fois dans ce mode dʼemploi et sur lʼap-

pareil lui-même, servent à signaler dʼimportants risques de sécurité. Ce qui suit permettra

de mieux comprendre la signification de ces mots clés et symboles.

Ce symbole sert à vous avertir aux dangers physiques potentiels. Le respect des consignes qui

le suivent vous permettra dʼéviter les risques de blessures graves ou mortelles.

Le terme DANGER signifie une situation dangereuse potentielle qui, faute dʼêtre

évitée, provoquerait la mort ou de graves blessures corporelles.

Le terme AVERTISSEMENT signifie une situation dangereuse potentielle

qui, faute dʼêtre évitée, serait susceptible dʼentraîner la mort ou de graves

blessures corporelles.

Le terme ATTENTION signifie une situation dangereuse potentielle qui, faute dʼêtre

évitée, serait susceptible dʼentraîner des blessures corporelles légères ou modérées.

Le terme AVIS IMPORTANT signifie des informations concernant la protection

des biens.

Ce symbole indique la nécessité de lire le manuel soigneusement avant dʼutiliser le matériel.

Le mode dʼemploi renferme dʼimportantes informations concernant la sécurité dʼutilisation

du matériel.

Ce symbole indique le port obligatoire de lunettes de sécurité intégrales lors de la manipu-

lation ou utilisation du matériel.

Ce symbole indique un risque dʼentraînement des mains, des doigts et autres membres par

le mécanisme de lʼappareil.

Ce symbole indique un risque de choc électrique.

flammer les poussières et émanations

combustibles.

• Eloignez les enfants et les curieux lors

de lʼutilisation dʼun appareil électrique.

Les distractions risquent de vous faire per-

dre le contrôle de lʼappareil.

Sécurité électrique

• Evitez tout contact avec les objets reliés

à la terre tels que canalisations, radia-

teurs, cuisinières et réfrigérateurs. Tout

contact avec la terre augmenterait les

risques de choc électrique.

• Nʼexposez pas lʼappareil à la pluie ou

aux intempéries. Toute pénétration dʼeau

à lʼintérieur dʼun appareil électrique aug-

menterait les risques de choc électrique.

Sécurité individuelle

• Soyez attentif, faites attention à ce que

vous faites et faites preuve de bon

sens. Nʼutilisez pas dʼappareil électrique

lorsque vous êtes sous lʼinfluence de

drogues, de lʼalcool ou de médicaments.

Lors de lʼutilisation dʼun appareil électrique,

un instant dʼinattention risque dʼentraîner

de graves lésions corporelles.

Consignes générales de

sécurité

AVERTISSEMENT

Familiarisez-vous avec l’ensemble du

mode d’emploi. Le non-respect des con-

signes d’utilisation et de sécurité ci-après

augmenterait les risques de choc élec-

trique, d’incendie et/ou de grave blessure

corporelle.

CONSERVEZ CES INSTRUCTIONS !

Lorsque cela sera nécessaire, la déclara-

tion de conformité CE (890-011-320) sera

jointe à ce manuel sous la forme d'un livret

distinct.

Sécurité des lieux

• Assurez-vous de la propreté et du bon

éclairage des lieux. Les zones encom-

brées ou mal éclairées sont une invitation

aux accidents.

• Nʼutilisez pas ce type de matériel en

présence de matières explosives telles

que liquides, gaz ou poussières com-

bustibles. Les appareils électriques pro-

duisent des étincelles susceptibles dʼen-

AVIS IMPORTANT

DANGER

AVERTISSEMENT

ATTENTION

• Utilisez exclusivement les accessoires

prévus par le fabricant pour votre type

dʼappareil particulier. Toute tentative

dʼadaptation dʼaccessoires prévus pour

dʼautres types dʼappareil pourrait sʼavérer

dangereuse.

• Maintenez les poignées de lʼappareil

en bon état de propreté et éliminez la

moindre trace dʼhuile ou de graisse.

Cela permettra de mieux tenir lʼappareil.

Révisions

• Confiez les révisions de votre matériel a

un réparateur qualifié utilisant exclu-

sivement des pièces de rechange iden-

tiques à celles dʼorigine. Cela assurera la

sécurité opérationnelle de lʼappareil.

Consignes de sécurité

spécifiques

AVERTISSEMENT

La section suivante contient d’impor-

tantes consignes de sécurité qui s’adres-

sent spécifiquement à la caméra d’in-

spection.

Afin de limiter les risques d’incendie et

de choc électrique ou autres blessures

graves, lisez le mode d’emploi soigneuse-

ment avant d’utiliser la caméra d’inspec-

tion micro CA-100.

CONSERVEZ CES INSTRUCTIONS !

Gardez ce mode dʼemploi dans le porte-

documents de la mallette de lʼappareil afin

quʼil soit à la disposition de tout utilisateur

éventuel.

Sécurité de la caméra d’inspec-

tion micro CA-100

• La tête de caméra et le câble de la micro

CA-100 sont étanches jusquʼà une pro-

fondeur de 3 mètres (10'). Son moni-

teur portable ne lʼest pas. Nʼexposez

pas le moniteur à lʼeau ou aux intempéries.

Cela augmenterait les risques de choc

électrique.

• Ne mettez pas la caméra dʼinspection

micro CA-100 dans un endroit suscep-

tible dʼêtre sous tension. Cela aug-

menterait les risques de choc électrique.

• Ne mettez pas la caméra dʼinspection

micro CA-100 dans un endroit suscep-

tible de contenir un mécanisme quel-

• Ne vous mettez pas en porte-à-faux.

Maintenez une bonne position de travail

et un bon équilibre à tout moment. Cela

vous permettra de mieux contrôler lʼap-

pareil en cas dʼimprévu.

• Prévoyez les équipements de protec-

tion individuelle nécessaires. Portez sys-

tématiquement une protection oculaire. Le

port dʼun masque à poussière, de chaus-

sures de sécurité antidérapantes, dʼun

casque de chantier ou de protecteurs dʼor-

eilles sʼimpose lorsque les conditions lʼex-

igent.

Utilisation et entretien du

matériel

• Ne forcez pas le matériel. Prévoyez le

matériel approprié en fonction des tra-

vaux envisagés. Le matériel approprié

fera le travail plus efficacement et avec

un plus grand niveau de sécurité lorsquʼil

tourne au régime prévu.

• Nʼutilisez pas de matériel électrique

dont lʼinterrupteur ne contrôle pas la

mise en marche ou lʼarrêt. Tout appareil

électrique qui ne peut pas être contrôlé

par son interrupteur est dangereux et doit

être réparé.

• Déconnectez les piles de lʼappareil

avant de le régler, de changer ses ac-

cessoires ou de le ranger. De telles

mesures préventives limiteront les risques

de blessure.

• Rangez tout appareil non utilisé hors

de la portée des enfants et des indi-

vidus qui nʼont pas été familiarisés avec

ce type de matériel ou son mode dʼem-

ploi. Ce type dʼappareil peut sʼavérer dan-

gereux entre les mains dʼutilisateurs non

initiés.

• Veillez à lʼentretien de lʼappareil. Exam-

inez-le pour signes de grippage, de bris et

de toute autre anomalie qui risquerait de

nuire à son bon fonctionnement. Le cas

échéant, faire réparer lʼappareil avant de

lʼutiliser. De nombreux accidents sont

provoqués par des appareils mal en-

tretenus.

• Lors de lʼutilisation de cet appareil et

de ses accessoires, respectez le mode

dʼemploi ci-présent en tenant compte

des conditions de travail existantes.

Lʼutilisation de cet appareil à des fins

autres que celles prévues pourrait créer

des situations dangereuses.

Caméra d’inspection micro CA-100

16

Caméra d’inspection micro CA-100

17

Etats-Unis et du Canada exclusivement,

en composant le (800) 519-3456.

Description,

caractéristiques

techniques et

équipements de base

Description

La caméra dʼinspection micro CA-100 affiche

des vidéos couleur venant dʼun capteur dʼim-

ages et dʼune source dʼéclairage qui sont reliés

à un flexible de 1 m (3') de long. Cette caméra

est capable dʼinspecter les endroits restreints

et exigus pour en renvoyer des images en

temps réel vers un moniteur LCD couleur. Elle

est équipée dʼune tête de caméra de 17 mm

(3/4") pour les applications courantes.

Caractéristiques techniques

Affichage .....................Moniteur LCD

couleur de 3,5" (ré-

solution : 320 x 240)

Eclairage .....................4 LED réglables

Longueur de câble ......3 pieds (30 pieds

avec rallonges

disponibles),

étanchéité : 10

pieds (norme IP67)

Tête de caméra ...........17 mm (3/4")

Sortie vidéo .................Type RCA sur câble

de 3 pieds

Sortie Télé ...................PAL/NTSC

Température de

fonctionnement............0 à 50 °C

Température

de stockage .................-20° C ~ 60° C

Humidité relative

(stockage)....................15 à 85 %

Profondeur de

champ (DOF)................10 mm à lʼinfini

Alimentation..................4 piles “AA”

alcalines ou

rechargeables

Accessoires ..................Crochet, aimant,

miroir

Poids.............................2,5 kg (5,5 livres)

conque. Cela augmenterait les risques

de blessure par enchevêtrement.

• Ne jamais utiliser cet appareil pour des

examens physiques ou médicaux. Ceci

nʼest pas un instrument médical. Il y aurait

risque de blessure corporelle.

• Prévoir systématiquement les équipe-

ments de protection individuelle appro-

priés lors de la manipulation ou utilisa-

tion de la caméra dʼinspection micro

CA-100. Les canalisations dʼévacuation

peuvent renfermer des produits chimiques,

des bactéries ou autres substances poten-

tiellement toxiques, infectieuses, irritantes ou

autrement dangereuses. Les équipe-

ments de protection individuelle appro-

priés comprennent systématiquement

les lunettes et gants de sécurité, voire

éventuellement des équipements supplé-

mentaires tels que gants en latex ou

caoutchouc, visières intégrales, lunettes

fermées, vêtements de protection, appareils

respiratoires ou chaussures de sécurité

blindées.

• Respectez les consignes dʼhygiène.

Après chaque manipulation ou utilisation

de la micro CA-100 pour lʼinspection des

canalisations ou autres éléments suscep-

tibles de renfermer des bactéries, lavez

vos mains et autres parties du corps ex-

posées à leur contenu avec de lʼeau

chaude savonneuse. Ne pas manger ou

fumer lors de la manipulation ou utilisation

de la caméra dʼinspection micro CA-100.

Cela aidera à éviter les risques de contam-

ination par contact avec des substances

toxiques ou infectieuses.

• Ne jamais utiliser la caméra dʼinspec-

tion micro CA-100 lorsque lʼutilisateur

ou lʼappareil a les pieds dans lʼeau.

Toute utilisation dʼun appareil électrique

avec les pieds dans lʼeau augmenterait

les risques de choc électrique.

Si nécessaire, la déclaration de conformité

CE 890-011-320.10 sera jointe à ce manuel

en tant que pamphlet séparé.

En cas de questions visant ce produit RIDGID

®

:

– Consultez votre distributeur RIDGID.

– Visitez le site www.RIDGID.com ou

www.RIDGID.eu pour localiser lʼinter-

locuteur le plus proche.

– Contactez les services techniques de

RIDGID par mail adressé à rtctechser-

vices@emerson.com, soit, à partir des

tion et utilisation conforme aux instructions,

risque de produire des interférences nuisi-

bles aux communications radio.

Cependant, il nʼest pas garanti quʼune telle in-

terférence nʼaura pas lieu dans une installation

donnée.

Si la mise en marche et lʼarrêt de ce matériel

devait éventuellement déterminer quʼil pro-

duit des interférences nuisibles à la récep-

tion radio ou télévision locale, il est conseillé à

lʼutilisateur dʼessayer dʼéliminer cette inter-

férence selon lʼune ou plusieurs des méthodes

suivantes :

• Réorientez ou déplacez lʼantenne de ré-

ception.

• Augmentez la distance entre le matériel et le

récepteur.

• Consultez le concessionnaire ou un techni-

cien radio/télé compétent pour obtenir de

lʼaide.

Compatibilité électro-

magnétique (EMC)

Le terme ʻcompatibilité électromagnétiqueʼ

sous-entend la capacité du produit à fonc-

tionner normalement en présence de radia-

tions électromagnétiques et de décharges

électrostatiques sans provoquer de parasites

électromagnétiques dans le matériel environ-

nant.

La caméra dʼinspection

RIDGID micro CA-100 est conforme à

lʼensemble des normes EMC. Cependant, il

existe toujours une possibilité dʼinterférence

avec dʼautres appareils.

Assemblage de l’appareil

AVERTISSEMENT

Afin de limiter les risques de blessure

grave en cours d’utilisation, respectez

les procédures suivantes lors de l’assem-

blage de l’appareil.

Remplacement des piles

La caméra dʼinspection micro CA-100 est

livrée ses piles non installées. Lorsque lʼindi-

cateur de charge tourne au rouge , les

piles devront être remplacées.

Afin dʼéviter les risques de fuite dʼélectrolyte,

retirez les piles avant le stockage prolongé de

lʼappareil.

Equipements de base

La caméra dʼinspection micro CA-100 est

livrée avec les articles suivants :

• Caméra dʼinspection micro CA-100

• Tête de caméra Ø 17 mm (3/4")

• Câble RCA de 3 pieds

• Crochet, aimant et miroir amovibles

• 4 piles “AA”

Figure 1 – Caméra dʼinspection micro CA-100

Commandes

Figure 2 – Commandes

Déclaration FCC

Cet appareil a été testé et homologué au titre

des limites établies pour les dispositifs

numériques Catégorie B par lʼarticle 15 de

la réglementation FCC. Ces limites ont été

établies afin dʼassurer une protection raison-

nable contre les interférences nuisibles dans

les installations résidentielles.

Ce matériel produit, utilise et risque dʼémettre

des fréquences radio et, faute dʼune installa-

AVIS IMPORTANT

Caméra d’inspection micro CA-100

18

Rotation

dʼimage

Marche/Arrêt

Diminution

de luminosité LED

Indicateur

de charge

Augmentation de

luminosité LED

La page charge ...

RIDGID micro CA-100 Manuel utilisateur

RIDGID micro CA-100 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents