Sylvania SDVD1256-C 11.6 Inch Portable Dvd Player Manuel utilisateur

"

11.6 SWIVEL PORTABLE DVD PLAYER

MODEL:SDVD1256-C

1

CAUTION: TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE

COVER (OR BACK). NO USER-

SERVICEABLE PARTS INSIDE. REFER

SERVICING TO QUALIFIED SERVICE

PERSONNEL.

CAUTION:

THIS DIGITAL VIDEO DISC PLAYER

EMPLOYS A LASER SYSTEM.

TO ENSURE PROPER USE OF THIS

PRODUCT.

PLEASE READ THIS OWNER`S MANUAL

CAREFULLY AND RETAIN FOR FUTURE

REFERENCE. SHOULD THE UNIT

REQUIRE MAINTENANCE, CONT ACT AN

AUTHORIZED SERVICE LOCATION-SEE

SERVICE PROCEDURE.

USE CONTROLS, ADJUSTMENTS OR

THE PERFORMANCE OF PROCEDURES

OTHER THAN THOSE SPECIFIED HEREIN

MAY RESULT IN HAZARDOUS RADIATION

EXPOSURE.

TO PREVENT DIRECT EXPOSURE TO

LASER BEAM, DO NOT TRY TO OPEN THE

ENCLOSURE. VISIBLE LASER RADIATION

MAY BE PRESENT WHEN THE ENCLOSURE

IS OPENED. DO NOT STARE INTO BEAM.

WARNING:

TO REDUCE THE RISK OF FIRE OR

ELECTRIC SHOCK, DO NOT EXPOSE THIS

PRODUCT TO RAIN OR MOISTURE.

WARNING:

TO REDUCE THE RISK OF FIRE OR

E L E C T R I C S H O C K , A N D A N N O Y I N G

INTERFERENCE, USE THE RECOMMENDED

ACCESSORIES ONLY.

SURGE PROTECTORS:

It is recommended to use a surge protector for

AC connection. Lightning and power surges

ARE NOT covered under warranty for this

product.

The lightning ash with arrowhead

symbol within an equilateral triangle

is intended to alert the user to the

presence of uninsulated dangerous

voltage within the product`s enclosure that may

be of sufcient magnitude to constitute a risk of

electric shock to persons.

The exclamation point within an

equilateral triangle is intended

to alert the user to the presence

of important operating and

maintenance(servicing) instructions in the

literature accompanying the appliance.

DANGER:

Invisible and hazardous laser

radiation when open and interlock

failed or defeated. Avoid direct

exposure to beam.

FCC NOTICE:

This equipment has been tested and found

to comply with the limits for a Class B digital

device, pursuant to part 15 of the FCC

Rules. These limits are designed to provide

reasonable protection against harmful

interference in a residential installation. This

equipment generates, uses and can radiate

radio frequency energy and, if not Installed

and used in accordance with the instructions,

may cause harmful interference to radio

communications.

However, there is no guarantee that

interference will not occur in a particular

installation. If this equipment does cause

harmful interference to radio or television

reception, which can be determined by

turning the equipment off and on, the user is

encouraged to try to correct the interference by

one or more of the following measures:

● Reorient or relocate the receiving

antenna. Increase the separation between

the equipment and receiver.

● Connect the equipment into an outlet

on a circuit different from that to which the

receiver is connected.

● Consult the dealer or an experienced

radio/TV technician for help.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

IMPORTANT SAFETY INSTRUCTION

CAN ICES-3 (B)/NMB-3(B)

2

FCC WARNING:

To assure continued compliance, follow the

attached installation instructions and use only

shielded cables when connecting to other

devices. Modifications not authorized by the

manufacturer may void user`s authority to

operate this device.

WARNING

USE UNDER SUPERVISION OF AN ADULT

DUE TO LONG CORD

This unit has a long AC cord or other long

cord that can easily be tripped on or pulled on,

causing injury, Please make sure it is arranged

so it will not drape over a tabletop, etc. Where

it can be pulled on by children or tripped over

accidentally.

EXERCISE CAUTION AS UNIT HAS SHARP

POINTS.

Before using the unit, be sure to read all

operating instructions carefully. Please note

that these are general precautions and may

not pertain to your unit.

1 ) Read these instructions.

All the safety and operating instructions should

be read before the product is operated.

2 ) Keep these instructions.

The safety and operating instructions should

be retained for future reference.

3 ) Heed all warnings.

All warnings on the product and in the

operating instructions should be adhered to.

4 ) Follow all instructions.

All operating and use instructions should be

followed.

5 ) Do not use this apparatus near water.

Do not use this product near water and

moisture, for example: near a bathtub,

washbowl, kitchen sink or laundry tub; in a wet

basement; or near a swimming pool.

6 ) Clean only with dry cloth.

Unplug this product from the wall outlet before

cleaning. Do not use liquid cleaners or aerosol

cleaners. Use a dry cloth for cleaning.

7)Do not block any ventilation

openings. Install in accordance with the

manufacturer's instructions.

Slots and openings in the cabinet and in the

back or bottom are provided for ventilation, to

ensure reliable operation of the product and

to protect it from overheating. These openings

must not be blocked or covered. The openings

should never be blocked by placing the product

on a bed, sofa, rug or other similar surface.

This product should never be placed near or

over a radiator or heat source. This product

should not be placed in a built-in installation

such as a bookcase or rack unless proper

ventilation is provided or the manufacturer's

instructions have been adhered to.

8 ) Do not install near any heat sources such

as radiators, heat registers, stoves, or other

apparatus(including amplifiers) that produce

heat.

9 ) Do not defeat the safety purpose of the

polarized or grounding-type plug. A polarized

plug

has two blades with one wider than the other. A

grounding type plug has two blades and a

third grounding prong. The wide blade or the

third prong are provided for your safety. If the

provided plug does not fit into your outlet,

consult an electrician for replacement of the

obsolete outlet.

10 ) Protect the power cord from being

walked on or pinched particularly at plugs,

convenience

receptacles, and the point where they exit from

the apparatus.

11 ) Only use attachments/accessories

specied by the manufacturer.

12 ) Use only with the cart, stand, tripod,

bracket, or table specied by the manufacturer,

or sold with the apparatus. When a cart is

used, use caution when

moving the cart/apparatus

combination to avoid injury

from tip-over.

An appliance and cart

combination should be

IMPORTANT SAFETY INSTRUCTION

3

moved with care.

Quick stop, excessive force and uneven

surfaces may cause the appliance and cart

combination to overturn.

13 ) Unplug this apparatus during lightning

storms or when unused for long periods of

time.

To protect your product from a lightning storm,

or when it is left unattended and unused for

long periods of time, unplug it from the wall

outlet and disconnect the antenna or cable

system.

This will prevent damage to the product due to

lightning and power-line surges.

14 ) Refer all servicing to qualified service

personnel. Servicing is required when the

apparatus

has been damaged in any way, such as power-

supply cord or plug is damaged, liquid has

been spilled or objects have fallen into the

apparatus, the apparatus has been exposed to

rain or moisture does not operate normally, or

has been dropped.

15 ) Power source.

This product should be operated only from the

type of power source indicated on the marking

label.

If you are not sure of the type of power supply

to your home, consult your appliance dealer or

local power company. For products intended

to operate from battery power, or other source,

refer to the operation instructions.

16 ) Power lines

An outside antenna system should not be

located in the vicinity of overhead power lines

or other electric light or power circuits, or where

it can fall into such power lines or circuits.

When installing an outside antenna system,

extreme care should be taken to keep from

touching such power lines or circuits as contact

with them might be fatal.

17 ) Overloading

Do not overload wall outlets and extension

cords as this can result in a risk of fire or

electric shock.

18 ) Object and liquid entry

Never push objects of any kind into the

product through openings as they may touch

dangerous voltage points or short out parts

that could result in re or electric shock. Never

spill or spray any type of liquid on the product.

19 ) Outdoor antenna grounding

If an outside antenna is connected to the

product, be sure the antenna system is

grounded so as to Provide some protection

against voltage surges and built up static

charges. Section 810 of the National Electric

Code ANSI/NFPA 70 provides information with

respect to proper to grounding of the mast and

supporting structure, grounding of the lead-

in wire to an antenna discharge product, size

of grounding conductors, location of antenna-

discharge product, connection to grounding

electrodes and requirements for the grounding

electrodes.

20 ) Service

Do not attempt to service this product yourself

as opening or removing covers may expose

you to dangerous voltage or other hazards.

Refer all servicing to qualified service

personnel.

21 ) Replacement parts

When replacement parts are required, be sure

the service technician uses replacement parts

specified by the manufacturer or those that

have the same characteristics as the original

parts.

Unauthorized substitutions may result in re or

electric shock or other hazards.

22 ) Safety check

Upon completion of any service or repairs

ANTENNA LEAD

IN WIRE

ANTENNA DISCHARGE UNIT

( NEC SECTION 810-20 )

GROUNDING CONDUCTORS

( NEC SECTION 810-21 )

POWER SERVICE GROUNDING

ELECTRODE SYSTEM

( NEC ART 250, PARTH )

GROUND CLAMPS

IMPORTANT SAFETY INSTRUCTION

4

to this product, ask the service technician to

perform safety checks to determine that the

product is in proper operational condition.

23 ) Wall or ceiling mounting

The product should be mounted to a wall

or ceiling only as recommended by the

manufacturer.

24 ) Damage requiring service

Unplug this product from the wall outlet and

refer service to qualified service personnel

under the

following conditions.

a ) When the power-supply cord or plug is

damaged.

b ) If liquid has been spilled or objects have

fallen into the product.

c ) If the product has been exposed to rain or

water.

d ) If the product does not operate normally

by following the operating instructions. Adjust

only those controls that are covered by the

operating instructions, as an adjustment of

other controls may result in damage and will

and require extensive work by a qualified

technician to restore in the product to its

normal operation.

e ) If the product has been dropped or the

cabinet has been damaged.

in performance-this indicates a need for

service.

25 ) Note to CATV system installer

This reminder is provided to call the CATV

system installer's attention to Article 820-40

of the NEC that provides guidelines for proper

grounding and, in particular, specifies that

the cable ground shall be connected to the

grounding system of the building, as close to

the point of cable entry as practical.

NOTE: Refer all servicing to qualied service

personnel Servicing is required when the unit

has been damaged in any way such as the

has been damaged, liquid has been spilled

into unit, the unit has been exposed to rain or

moisture, the unit has been dropped or the unit

does not operate normally.

NOTES ON HANDLING:

● When shipping the unit, always use the

original shipping carton and packing materials.

For maximum protection, repack the unit as it

was originally packed at the factory.

● Do not use volatile liquids, such as insect

spray,

near the unit. Do not leave rubber or plastic

products in contact with the unit for a long time.

They will leave marks on the nish.

● The top and rear panels of the unit

may become warm after a long period of use.

This is normal and not a malfunction.

● When the DVD player is not in use, be sure

to remove the disc and turn off the power.

NOTES ON LOCATING THE DVD PLAYER:

When you place this unit near a TV, radio or

VCR, the playback picture may become poor

and the sound may be distorted. In this case,

move the unit away from the TV, radio or VCR.

NOTES ON CLEANING:

Use a soft, dry cloth for cleaning

● For stubborn dirt, soak the cloth in a weak

detergent solution, wring well and wipe. Use a

dry cloth to wipe it dry. Do not use any type of

solvent, such as thinner and benzene, as they

may damage the surface of the unit.

● If you use a chemical-saturated cloth to clean

the unit, follow that product's instructions.

Warning: Cleaning and adjustment of

lenses and /or other components of playback

mechanism should be performed by a qualied

service technician.

NOTES ON MOISTURE CONDENSATION:

Moisture condensation damages the DVD

player.

Please read the following carefully.

● Moisture condensation occurs, for example,

when you pour a cold drink into a glass on a

warm day. Drops of water form on the outside

IMPORTANT SAFETY INSTRUCTION

f ) When the product exhibits a distinct change

following: the power-supply cord or plug

5

of the glass. In the same way, moisture may condense on the optical pick-up lens inside this unit,

one of the most crucial internal parts of the DVD player.

Moisture condensation occurs during the following cases:

● When you bring the DVD player directly from a cold place to a warm place.

● When you use the DVD player in a room where you just turned on the heater, or a place where the

cold wind from the air conditioner directly hits the unit.

● ln summer, when you use the DVD player in a hot and humid place just after you moved the unit

from an air conditioned room.

● When you use the DVD player in a humid place.

Do not use the DVD player when moisture condensation may occur.

● lf you use the DVD player in such a situation, it may damage discs and internal parts. Remove the

disc, connect the AC/DC Adaptor to the DVD player and the wall outlet, turn on the DVD player and

leave it ON for two or three hours. After two or three hours, the DVD player will have warmed up

and evaporated any moisture.

IMPORTANT SAFETY INSTRUCTIONS

6

See the following page for information regarding region numbers.

PLAYABLE DISCS:

The following discs can be played back on this DVD player:

DISC TYPES:

DVD

Data on most DVDs is divided into sections called titles

and then into subsections called chapters, each of which

is given a title or chapter number. Some features of this

DVD player will not operate with some DVD discs as they

are preset. If a function you selected does not run as

desired , refer to the manual accompanying the DVD disc.

AUDIO CD

Data on an audio CD is divided into sections called tracks ,

each of which is given a track number.

IMPORTANT:

It is important that you read the manual that accompanies the DVD disc , as there are features that

are on the DVD player that cannot be used with certain DVDs .

There are also extra features on the DVD disc that are different for each DVD disc, so they are not

explained in this owner's manual.

This player conforms to the NTSC and PAL color systems . However , if you are in the USA , Canada

or Mexico,leave this setting on NTSC . If incorrectly set to PAL ,the TV picture may roll vertically. In

this case , set the TV system to NTSC.

Notes on Copyright:

It is forbidden by law to copy, broadcast, show, broadcast on cable, play in public and rent

copyrighted material without permission. DVD video discs are copy protected, and any recordings

made from these discs will be distorted. This product incorporates copyright protection technology

that is protected by method claims of certain U.S. Patents and other intellectual property rights

owned by Macrovision

Macrovision Corporation, and is intended for home and other limited viewing uses only, unless

otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited.

Region Management Information:

This DVD Player is designed and manufactured to respond to the Region Management Information

that is recorded on a DVD disc. If the Region number described on the DVD disc does not

correspond to the Region number of this DVD player, this DVD player cannot play that disc. You may

not be able to play back some DVD video discs on this player if they were purchased from outside

your geographic area or made for business purposes. When you try to play back an unauthorized

disc, Wrong Region appears on the TV screen.

ABOUT DISCS

The region number for this DVD Player is: 1

7

Press to enter to AV IN mode; press again to resume normal mode.

Press to decrease volume level.

LOCATION OF CONTROLS

Push the"OPEN" button to open the disc door.

Press to confirm the operations.

Press to increase volume level.

Press to skip to previous track or cursor upward.

Press to skip to next track or cursor downward.

SOURCE

1 2 3 4 5 6 7 8 9 10

11

2.VOL- (Volume Down) button:

3.VOL+ (Volume Up) button:

4.OPEN button:

5.SOURCE button:

6.Fast Backward/Left button:

7.OK button:

8.Next/Down button:

9.Fast forward/Right button:

10.Play/Pause/STOP button:

11.Previous/Up button:

Press to fast forward or cursor right.

Press to fast backward or cursor left.

When USB device and/or SD Card was inserted, press

repeatedly to select the playback source as desired.

1.DVD/USB/CARD button:

press and hold about 3 seconds again to fully stop.

Press to start playback or pause, press and hold about 3 seconds

to pre-stop,

8

12. USB Port

13. MMC/SD Slot

14. EARPHONE Jack

15. AV OUT Jack

16. AV IN Jack

17. Power OFF/ON Switch: Slide to ON

position to power on. Slide to OFF position to

shut off.

18. DC IN Jack:

)

LOCATION OF CONTROLS

Right Side View:

Front Side View:

DC input jack (DC 9-12V, 1A

12 13 14 15 16 17 18

19 20

19. POWER/CHARGE Indicator 20. Remote Sensor

POWER/

CHARGE IR

9

1

2

3

4

5

6

7

89

10

11 12

13 14

15

16

17

18

19

20

21

22

23

24

25

26

27

28

2. VOLUME +/– Buttons

4. MENU Button

ŻŻ

7.

ǿŻŻ

6. Button

12.

15. SLOW Button

Button

16. LCD ON/OFF Button

17. Numeric Buttons

18. SETUP Button

19. Button

ǿŻŻ

20. Button

ŻŻ

21. OSD (On Screen Display Button

22. SUBTITLE Button

23. ANGLE Button

24. PROG (Program Button

26. STEP Button

27. ZOOM Button

28. A-B Repeat Button

9.

TITLE Button

8.

USB/CARD Button

10.

AUDIO Button

REPEAT Button

13.

11. (

14.

GOTO Button OK

25. Button

3. MUTE Button

5. Direction Buttons

( Play/Pause Button



6723 %XWWRQ



Ŷ



REMOTE CONTROL

MENU

TITLE

Ok

1. POWER Button

POWER

10

BATTERY INSTALLATION (REMOTE CONTROL)

directions.)

Remote Control Sensor

battery compartment as the figure on righ and the

polarity markin

battery door and lift it off.

2.Install two (2) x AAA size batteries into the

Remarks:

1. When there is an obstacle between the unit and the transmitter, the transmitter may not operation.

2. When direct sunlight, an incandescent lamp, fluorescent lamp or any other strong light shines on the

remote control of the unit, the remote operation may be unstable.

POWER

POWER/

CHARGE IR

11

The unit has a built-in DC 7.4V Lithium-ion rechargeable battery.



Connect the small plug from the supplied AC/DC Adaptor to the DC IN Jack on the right of unit.

 Connect the AC/DC Adaptor to the wall outlet having

 During charging, the

1%7KH$&'&$GDSWRULVLQWHQGHGWREHFRUUHFWO\RULHQWDWHGLQD

1RWHV Your battery will last longer if you follow these simple guidelines for caring for and storing it.

$

%

Recharge and store the device within the temperature range of 5°C~35°C (40°F~95°F).

&

Do not overcharge (longer than 24 hours). Excessive charging or

Battery life naturally shortens slowly over time.

2. This is a special negative grounded

Car Adapter. Using this Car Adapter

with a plus grounded car can cause

malfunction.

3. Do NOT plug in the Car Adapter until

the car ignition is turned on.

4. Disconnect the Car Adapter from the

cigarette ligher and the unit after use. To the cigarette

lighter socket

To DC IN Jack on the unit

as follows:

Charging by supplied AC/DC Adaptor:

Red Indicator will turn on. When finished, it will turn off.

discharging may shorten the

battery’s life.

Charging by the supplied Car Adaptor:

1. Connect to the cigarette lighter socket of a vehicle that has a 12V battery as the figure below.

a vehicle that has a 24V battery.a vehicle that has a 24V battery.

It is compatible withIt is NOT compatible withNOT

Charging by supplied AC/DC Adaptor:

Charging by the supplied Car Adaptor:

AC 100-240V~; 50/60Hz.

POWER SOURCE

Recharge it

YHUWLFDORUÀRRUPRXQWSRVLWLRQ

12

Audio/Video cable

Connected to the TV Connected to the Video Player

AUDIO OUT

LR

120V ~ 60Hz

VIDEO OUT

VIDEO

Video Player

DIGIT A L

Video input jack ( Yellow )

Audio left channel input jack ( White )

Audio right channel input jack ( Red )

CONNECTIONS

1.Connecting to a TV or Video Player (such like DVD; VCR; DVR Players ... ) with AV connection cable

NOTE:

The default setting of the unit is AV Out, if connect to external Video

to turn back to AV Out mode.

Player (such like DVD;

VCR; DVR Players ... ), press the MODE Button to set to AV IN mode ("AV IN" will appear

on the screen). Press again

Using the earphone to listen privately.

13

3. During playback:

~ Press the or Buttons repeatedly to fast search for a specific section forward/backward.

Press Play Button to resume normal playback.

~ Press the or Buttons repeatedly to skip to specific track.

~ Press Button to pause, press Button again to resume normal playback.

Repeat Playback:

Chapter will playback.

Press the REPEAT button twice; “ Title ” will appear on the screen then the current Title will playback.

Chapter

Press the REPEAT button the third time; “ All ” will appear on the screen then all files will playback.

~ Press the VOL (Volume) +/- Buttons to adjust volume level.

(CD)

Repeat Playback:

During playback, press the REPEAT Button once; ” will appear on the screen then the current

playing track will playback.

playback.

Track

the Power ON/OFF switch to "ON" position to power on the unit,

Close the disc door and the player will start playback automatically.

1. Lift up the panel and turn to desired angle. Slide

the Green Indicator on front of the player will light.

(For saving energy, always power off the player by slide the Power ON/OFF Switch on the player to OFF

position or unplug the AC/DC Adaptor from player and wall outlet.)

until all the repeat indicators disappear on the screen to turn off the

Press the REPEAT button repeatedly

the repeat mode.

until all repeat indicators disappear on the screen

Press the REPEAT Button repeatedly to turn off repeat mode.

Press the REPEAT Button twice; “ ALL ” will appear on the screen then all the tracks on the disc will

During playback, press the REPEAT button once; “ ” will appear on the screen then the current

OPERATIONS

(DVD)

 352*



1

2

3

4

5

TT:02 CH: 01

TT: CH:

6

7

8

9

10

TT: CH:

1

2

3

4

5

02

04

6

7

8

9

10

B_

press the

During CD or DVD playback, ( Program )

Using the Direction Button to select and highlight the "START" Button on the screen then press the OK

Button to start program playback.

(CD/DVD)Program:

Using the Direction and Numeric Buttons to select and set the desired TT (Title), CH (Chapters), tracks (for CD)

of the movie (music) you wants. The Program menu will appear as follows.

button.

DVD CD

EXIT NEXTSTART

2. Push OPEN Switch to open the disc door. Place the disc on the center spindle with label side facing up.

EXIT NEXTSTART

~ Press and hold the STOP Button about 3 seconds to stop playback. The player will remember the point

where disc was stopped. When press Play/Pause Button again, playback will start from this point.

To stop playback completely

3 seconds.

or to start from the beginning, press and hold the STOP Button again about

4. To power off, press the POWER Button on the Remote Control to turn the player to standby mode.

Press the POWER Button again to turn the player on from standby mode.

14

VOL/Volume +/–

Press to increase or decrease volume.

MUTE

LCD ON/OFF

Press to turn on or off the LCD display.

SUBTITLE

ANGLE

Press to turn off the sound, press again to resume.

(Function depends on the recording of

During DVD playback, press repeatedly to select the

viewing angle

disc).

During DVD playback, press repeatedly to select the

desired subtitle (Function depends on the recording

of disc).

OPERATIONS

TITLE

depends on the recording of the disc).

Press to return to disc's title page (Function

MENU

depends on the recording of the disc).

Press to return to disc's menu page (Function

OSD (On Screen Display)

During playback, press the OSD button repeatedly to

read the information of playback status.

STEP

During movie playback, press STEP Button repeatedly

to play the movie frame by frame.

Press the Play/Pause Button to resume normal

playback.

ZOOM

During movies playback, press the ZOOM Button

repeatedly to zoom in/out the picture. In zoom mode,

press Direction Buttons to select the parts of the zoomed

picture to watch. This function is not available on all

discs.

SLOW

A-B Repeat

During Playback, press the A-B Button to define where

you want the section to start. Press the A-B Button again

to define where you would like the section to end, the

unit will then plays the selected section repeatedly

and continuously. Press the A-B Button again to resume

normal playback.

(This function is not available on all discs).

During playback, press the SLOW Button repeatedly

to set the slow motion speed. Press Play/Pause

Button to resume normal playback.

GOTO

~ To select the desired Title and Chapter, press the

GOTO Button once, the Title and Chapter selection

menu will appear on the screen. Use the Direction

and Numeric Buttons to select the desired title and

automatically.

~ Select the desired establish time by Title to play,

press the GOTO Button twice, the time selection

table appear on the screen. Using the Direction and

Numeric Buttons to enter the desired time.

The unit will start plays the movie from the selected

established time automatically.

AUDIO

During DVD playback, press repeatedly to select the

desired language (Function depends on the recording

of disc).

chapter. The unit will play the selected chapter

~ Select the desired establish time by Chapter to play,

press the GOTO Button three times, the time

selection table appear on the screen. Using the

Direction and Numeric Buttons to enter the desired

time. The unit will start plays the movie from the

selected establish time automatically.

POWER

Press to turn to standby mode. Press again to turn on.

1. Insert the USB Device or SD/MMC memory card into the USB port /card slot as the gure below.

NB: The unit supported to playback:

~ MP3; WMA (Music le)

~ JPG (Pictures)

Make sure correct les were saved in the USB device or memory cards.

USB or SD/MMC CARD PLAYBACK

~ MPEG2; AVI; VOB (Video les up to 640 x 480 pixels)

3. During playback:

~ Press the or Button repeatedly to skip tracks.

~ Press the Play/Pause Button to pause. Press again to resume.

NOTE: For saving battery power. If long period of time will not use, power off

the unit by slide the POWER ON/OFF Switch to OFF position.

ǿŻŻ

~ Press the or Button repeatedly to select and set the fast searching speed.

Using the earphone to listen privately.

15

OK Button to confirm. Press the OK Button again, the Folder/File list will appear.

using the Direction button to select the desired file then press the OK Button to start playback.

Button on the panel, the "DVD, CARD, USB" selection window

2. In Power ON mode, press the USB/CARD Button will pop up on the screen.

Using the Direction Buttons to select and highlight the desired source, then press the

on remote control, or press DVD/USB/CARD

4. When finished, press the STOP Button to stop. Press the POWER Button

to power off (Standby) the unit.

Ŷ

16

- - General Setup Page - -

Go To General Setup Page

TV Shape Wide

Angle Mark On

OSD Lang Eng

Screen Saver On

Setting Menus:

◄,►,▲,▼need to set or reset. Press the OK

Buttonto enter or confirmed the selection. After setting, press the SET UPButtonto save the settings and exit.

In stop playback mode, press the SETUP Button the setting menu will appear on the screen as below. Using the

Direction Buttons to select and highlight the function you

In General Setup Page:

the multi-angle logo will appear on the screen.

or the image is paused for approximately five minutes.

On or Off. If set to On, when

multi-angles are available in the playing DVD,

Direction and OK Buttons to set the

OSD language as desired.

Off. If set to On, the

screen saver will come on when the unit stops it On or

5. If Last Memory is selected, using the Direction and OK Buttons to set it On or Off. If set to On, the unit

will start playback from the position where the disc was stopped last time.

1. If TV Shape is selected, using the Direction and OK Button to set the aspect ratio to match the

connected TV.

2. If Angle Mark is selected, using the Direction and OK buttons to set it

OSD Lang (On Screen Display Language) is selected, using the3. If

4. If Screen Saver is selected, using the Directionand OK Buttonsto set

In Audio Setup Page:

menu will appear.

to Lt/Rt; Stereo.

If Speaker Setup is selected, press the OK Button, the sub-setting

1. If Downmix is selected, using the Direction and OK Buttons set it

~ If set to Lt/Rt, the rear left or rear right channels will plays on both Left and Right Speakers.

~ If set to Stereo, the rear left channel will plays on Left Speaker; the rear right channel will plays on Right

Speaker.

In Dolby Setup Page:

channel on all speakers) or Mix-Mono

plays on all speakers) as desire. (Functions depend on the recording of the disc).

to Stereo, L-Mono (Play Left

channel on all speakers), R-Mono (Play Right (Mixed Right and

Left channel then

1. If Dual Mono is selected, using the Direction and OK Buttonsto set it

2. If Dynamic is selected, using the Direction and OK Buttons to set the dynamic level as desired or turn

it off.

SYSTEM SETUP

Last Memory Off

17

In Video Setup Page:

1. If "Picture" is selected, using the Direction and OK Buttons to set the panel quality such

Sharpness; Brightness; Contrast; Hue or Saturation as desired. Sharpness; Brightness;

Contrast; Gamma; Hue or Saturation as desired.

In Preference Setup Page:

DVD).

~ Press the ►

~ Press the ▲or ▼

~ Rate levels:

2 (G): All ages

6 (R): Under 17 years old, Parental Guidance strongly

8 (Adult): Adult only

PAL,AUTO or NTSC.

(Function depend the recording of

menu will appear.

~ Enter the six digit old password. The Colum of New Password will be highlighted.

~ Enter the new six digit password. The Colum of Confirm Pwd will be highlighted.

to set it On (activate the

rating level setting) or

New password setting menu

will appear.

the OK Buttonto save the setting and exit.

setting to default setting or

rection and OK Buttonsto set to1. If TV Type is selected, using the Di

of the available language.

2. If Audio, Subtitle or Disc Menu is selected, using the Direction and OK buttons to the priority

3. If Parental is selected, using the Direction and OK Buttons to set the rating level as desire as follow:

~ Enter the six digit password ( default password is 136900 ) by pressing the Numeric Buttons.

~ Press the OK Button to save the settings and exit.

1 (Kid Saf ): Kid safe

3 (Pg): Parental Guidance

4 (Pg 13): Parental Guidance less than 13 years old

5 (Pgr): Under 17 years old, Parental Guidance suggested

7 (Nc 17): 17 years old or above

Off (Password is needed).

4. If Password is selected, press the OK Buttonto enter, the subsetting

~ If Password Mode is selected, using the Direction and OK buttons

~ If Password is selected, press the OK Buttontwice to enter. The

~ Enter the new password again. OK Button will be highlighted.

Press on the screen

5. If Default is selected, using the Direction and OK Buttonsto reset all

press the SETUP Button to exit without changes.

Button to enter, the rating level list will appear.

Button to select the desired level.

~ Press the OK Button to enter, password enter window will pop up.

2. If Picture Quality is selected, using the Direction and OK Buttons to set the

of the Video input signal

like

SYSTEM SETUP

(NOTE: The TV system in USA, Canada and Mexico is NTSC.)

18

Caring for Discs

Treat the disc carefully. Handle the disc only by its edges.

Never allow your ngers to contact with the shiny, unprinted side of the disc.

● Do not attach adhesive tape, stickers, etc. to the disc label.

● Clean the disc periodically with a soft, lint-free,dry cloth, Never use detergents or abrasive cleaners

to clean the disc. If necessary, use a CD cleaning kit.

● If a disc skips or gets stuck on a section of the disc, it is probably dirty or damaged(scratched).

● When cleaning the disc, wipe in straight lines from the center of the disc to the outer edge of the

disc. Never wipe in circular motions.

● Discs should be stored in their cases after each use to avoid damage.

● Do not expose discs to direct sunlight, high temperatures or dust, etc. Prolonged exposure or

extreme temperatures can warp the disc.

● Do not stick or write anything on either side of the disc. Sharp writing Instruments, or the ink, may

damage the surface.

Cleaning the Unit

● To prevent re or shock hazard, disconnect your unit from the AC power source when cleaning.

● The nish on your unit may be cleaned with a dust cloth and cared for as other furniture. Use

caution when cleaning and wiping the plastic parts.

● Mild soap and a damp cloth may be used on the front panel.

CARE AND MAINTENANCE

19

ACCESSORIES

SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE

Power Source:

Power Source: Built-in DC 7.4V Lithium-ion rechargeable battery, recharge by DC 9-12V, 1A through DC IN Jack

Power Source of Remote Control: DC 3V, 2 x AAA Size Batteries (included)

Disc Compatibility:

1 x User's Manual

1 x Remote Control with 2 x AAA Size Batteries

SPECIFICATIONS

1 x AC/DC Adaptor

1 x Car Adaptor

DVD/VCD/SVCD/DVCD/CD/CD-R/CD-RW/DVD±R/DVD±RW

1 x A/V Cable

La page charge ...

Sylvania SDVD1256-C 11.6 Inch Portable Dvd Player Manuel utilisateur

Sylvania SDVD1256-C 11.6 Inch Portable Dvd Player Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents