Sixnet RAM 9000 Hardware Guide d'installation

Marque: Sixnet

Modèle: RAM 9000 Hardware

Taper: Guide d'installation

Sixnet

Series

RAM

9000

Hardware Guide | February 2016

Cellular RTUs

of Red Lion Controls, Inc. All other company and product names are trademarks of their respective owners.

Red Lion Controls, Inc.

20 Willow Springs Circle

York, PA 17406

CONTACT INFORMATION:

AMERICAS

York, PA: +1 (717) 767-6511

Mobile, AL: +1 (251) 342-2164

Ballston Lake, NY: +1 (518) 877-5173

Hours: 8am-6pm Eastern Standard Time

(UTC/GMT -5 hours)

ASIA-PACIFIC

Shanghai, P.R. China: +86 21-6113-3688 x767

Hours: 10am-6pm China Standard Time

(UTC/GMT +8 hours)

EUROPE

The Netherlands: +31 33-4723-225

Hours: 9am-6pm Central European Time

(UTC/GMT +1 hour)

Website: www.redlion.net

Email: [email protected]

Sixnet

Series RAM

9000 Hardware Guide i

Table of Contents Revised 2016-02-12

Preface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii

Disclaimer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii

Compliance Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii

Part 15 of the Federal Communications Commission (FCC) - A Rules: Interference . . . . . . . . . . . . . . . . . . . . . . . . iii

Industry Canada . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii

Environmental Impact Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii

Toxic Emissions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii

Trademark Acknowledgments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iv

Release Notes and Document Updates. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iv

Publication History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iv

Related Documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iv

Document Ordering Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iv

Document Comments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .v

Additional Product Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .v

Safety Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .v

Warnings/Cautions/Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .v

Hazardous Location and Installation Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .v

AVERTISSEMENTS POUR INSTALLATION ET ENDROITS DANGEREUX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .v

Environmental. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vi

Electrical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii

Statement of Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ix

Chapter 1 Product Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

RAM

9000 Cellular RTU Product Highlights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2

General Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2

RAM 9000 Model Comparison Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6

RAM 9000 Cellular RTU View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7

Power Specifications and Consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7

Electrical Specifications and Pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-8

Indicator Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-11

Bootup LED Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-12

Data Interface Specifications: Serial, Ethernet & USB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-13

Mode/Reset Button functions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-14

Ordering Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-17

Chapter 2 Hardware Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-19

Mounting the RAM 9000 Cellular RTU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-19

DIN Rail Mounting & Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-19

Revised 2016-02-12 Table of Contents

ii Sixnet

Series RAM

9000 Hardware Guide

Mechanical Dimension Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-21

Antennas and Wireless . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-21

GPS Antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-24

Installation and Verification. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-24

Wi-Fi Antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-24

Ethernet cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-25

USB Device Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-25

USB Host Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-25

Serial RS485 Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-25

RS485 Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-27

Serial RS232 Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-27

Power Source. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-28

Powering the unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-28

Testing the power connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-28

6-pin Screw Terminal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-28

Power Input Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-29

Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-29

Battery Removal and Installation: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-30

SIM Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-31

SD Card. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-32

I/O Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-32

I/O Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-33

Equivalent Circuit Diagrams. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-34

Thermal Performance and Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-34

Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-35

Service and Support Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-37

Service Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-37

Product Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-37

Sixnet

Series RAM

9000 Hardware Guide iii

Preface Revised 2016-02-12

Preface

Disclaimer

Portions of this document are intended solely as an outline of methodologies to be followed during the

maintenance and operation of the RAM 9000 equipment/software. It is not intended as a step-by-step guide or a

complete set of all procedures necessary and sufficient to complete all operations.

While every effort has been made to ensure that this document is complete and accurate at the time of release, the

information that it contains is subject to change. Red Lion Controls is not responsible for any additions to or

alterations of the original document. Industrial networks vary widely in their configurations, topologies, and traffic

conditions. This document is intended as a general guide only. It has not been tested for all possible applications,

and it may not be complete or accurate for some situations.

Users of this document are urged to heed warnings and cautions summarized at the front of the document, such as

electrical hazard warnings.

Compliance Information

Part 15 of the Federal Communications Commission (FCC) - A Rules: Interference

Every effort has been made to ensure that this equipment is designed to comply with the limits for a Class A digital

device, as described in the FCC Rules. This equipment has been tested and found to comply with the limits for a

Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment generates, uses, and can

radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause

harmful interference to radio communications. Operation of this device in a residential area is likely to cause

harmful interference in which case the user will be required to correct the interference at his/her own expense.

Industry Canada

This Class A digital apparatus meets all requirements of the Canadian Interference Causing Equipment

Regulations. Operation is subject to the following two conditions; (1) this device may not cause harmful

interference, and (2) this device must accept any interference received, including interference that may cause

undesired operation.

Environmental Impact Statement

Red Lion equipment contains no hazardous materials as defined by the United States Environmental Protection

Agency (USEPA). Red Lion recommends that all failed product be returned to Red Lion for failure analysis and

proper disposal.

Toxic Emissions

Red Lion equipment releases no toxic emissions.

iv Sixnet

Series RAM

9000 Hardware Guide

Revised 2016-02-12 Preface

Trademark Acknowledgments

• Windows

/98/2000/7/8, Windows XP

are registered trademarks of the Microsoft Corporation.

• Microsoft is either a registered trademark or trademark of Microsoft Corporation in the United States and/or

other countries.

• Ethernet

is a registered trademark of Xerox Corporation.

• EtherNet/IP

and CIP

are registered trademarks of ODVA

• All other company and product names are trademarks of their respective owners.

Release Notes and Document Updates

The hard copy and flash drive versions of this document are revised only at major releases and, therefore, may not

always contain the latest product information. As needed, Application Notes and or Product Bulletins will be

provided between major releases to describe any new information or document changes.

The latest online version of this document and all product updates can be accessed through the Red Lion web site

at www.redlion.net/documentation

Publication History

The following information lists the release history of this document.

ISSUE/REVISION RELEASE DATE CONTENT DESCRIPTION

R06 February 2016 JP and 3.23/4.23 release.

R05 September 2015

EU release. Added uniform Warranty Statement and document

template

R04 March 2015 Updates to Warnings

R03 September 2014 Modifications to FCC Statement to cellular frequency bands

R02 August 2014

Wi-Fi capability added. Change to operating temperature and

thermal performance

R01 April 2014 First release

Related Documents

The following information lists available documents related to this product.

ISSUE/REVISION RELEASE DATE DOCUMENT TITLE

Version 7 February 2016 SN/RAM 6000 & RAM 9000 Software Manual

Version 6 March 2015 RAM 9000 Quick Start Guide

Version 6 February 2015 RAM 6000 Quick Start Guide

Sixnet

Series RAM

9000 Hardware Guide v

Preface Revised 2016-02-12

Document Ordering Information

To order additional documentation, the user can contact the local sales representative or Red Lion through the

contact numbers and/or e-mail addresses listed on the back of the cover.

Document Comments

Red Lion appreciates all comments that will help us to improve our documentation quality. The user can submit

comments through the Red Lion Customer Service. Simply email us at customer[email protected].

Additional Product Information

Additional product information can be obtained by contacting the local sales representative or Red Lion through the

contact numbers and/or e-mail addresses listed on the back of the cover.

Safety Information

Must consult guide in all cases where this symbol is marked.

Warnings/Cautions/Notes

Warnings apply to situations where personal injury or death may result.

Cautions apply where damage to equipment may result

Notes apply where additional noteworthy information, not in the general text flow but applicable, is made available

to the user.

Hazardous Location and Installation Requirements

These products should not be used to replace proper safety interlocking. No software-based device (or any other

solid-state device) should ever be designed to be responsible for the maintenance of consequential equipment or

personnel safety. In particular, Red Lion disclaims any responsibility for damages, either direct or consequential,

that result from the use of this equipment in any application.

All power, input and output (I/O) wiring must be in accordance with Class I, Division 2 wiring methods and in

accordance with the authority having jurisdiction.

Suitable for use in Class I, Division 2, Groups A, B, C and D hazardous locations, or non-hazardous locations only.

These products are operator interface units to be used within control panels in hazardous locations. The enclosure

shall be suitable for the location.

AVERTISSEMENTS POUR INSTALLATION ET ENDROITS DANGEREUX

Ces produits ne doivent pas être utilisés pour remplacer le verrouillage de sécurité approprié. Aucun dispositif

basé sur un logiciel (ou tout autre dispositif à l'état solide) devraient jamais être conçus pour être responsable de

l'entretien de l'équipement consécutifs ou la sécurité du personnel. En particulier, Red Lion décline toute

vi Sixnet

Series RAM

9000 Hardware Guide

Revised 2016-02-12 Preface

responsabilité pour les dommages, directs ou indirects, résultant de l'utilisation de cet équipement dans n'importe

quelle application.

Tout courant, câblage entrée et sortie (I / O) doit être conforme aux méthodes de câblage à la Classe I, Division 2

et conformément à l'autorité compétente.

Cet appareil est adapté pour utilisation en Classe I, Division 2, Groupes A, B, C, D endroits dangereux ou endroits

non-dangereux.

Ces produits sont des unités d'interface opérateur qui doivent être utilisés à l'intérieur des panneaux de commande

dans les endroits dangereux. L'enclos doit être adapté à l’environnement.

WARNING: Explosion Hazard – Substitution of components may impair suitability for Class I,

Division 2.

AVERTISSEMENT - Risque d'explosion -

La substitution de tout composant peut nuire à la

conformité de Classe 1, Division 2.

WARNING – Explosion Hazard – When in hazardous locations, disconnect power before

replacing or wiring modules.

AVERTISSEMENT – Risque d’explosion - Lorsque dans des endroits dangereux, débran-

chez le cordon d’alimentation avant de remplacer ou de brancher les modules.

WARNING – Explosion Hazard – Do not disconnect equipment unless power has been

switched off or the area is known to be non-hazardous.

AVERTISSEMENT - Risque d'explosion -

Ne débranchez pas l’équipement à moins que

l’alimentation ait été coupée ou que l’environnement est connu pour être non dange-

reux.

WARNING - Explosion Hazard - Exposure to some chemicals may degrade the sealing

properties of materials used in the relays.

AVERTISSEMENT - Risque d'explosion - L’exposition à certain produits chimiques peut

dégrader les propriétés d’étanchéité des matériaux utilisés dans les relais.

WARNING - Explosion Hazard - Batteries must only be changed in an area known to be

non-hazardous.

AVERTISSEMENT - Risque d'explosion - Batteries doivent être changées dans une zone

connue pour être non dangereuse.

Sixnet

Series RAM

9000 Hardware Guide vii

Preface Revised 2016-02-12

Environmental

The unit may become very hot to the touch in high temperature environments, so extreme caution should be

exercised in handling when energized. The unit should be disconnected from power and allowed to cool for

approximately 5 minutes before touching in high temperature applications.

WARNING: Disconnect the power and allow to cool 5 minutes before touching.

AVERTISSEMENT: Déconnectez le câble d'alimentation et laisser refroidir 5 minutes avant de la

toucher.

Pollution degree: 2 (Per IEC 61010-1)

Electrical

WARNING: Device must be supplied by a Class 2 power source.

AVERTISSEMENT: l'appareil doit être alimenté par une source d'alimentation de classe 2.

Over-voltage category: II (Per IEC 61010-1)

WARNING: Properly ground the unit before connecting anything else to the unit. Units not

properly grounded may result in a safety risk and could be hazardous and may void the warranty.

See the grounding technique section of this manual for proper ways to ground the unit.

AVERTISSEMENT: L'unité doit être correctement mise à la terre avant tout raccordement à

l'unité. Unités pas correctement mise à la terre peuvent causer un risque de sécurité et pour-

raient être dangereuses et peuvent annuler la garantie. Voir la section technique de mise à la

terre dans ce mode d'emploi pour des moyens appropriés à la masse de l'appareil.

Sixnet

Series RAM

9000 Hardware Guide viii

Preface Revised 2016-02-12

Sixnet

Series RAM

9000 Hardware Guide ix

Statement of Limited Warranty Revised 2016-02-12

Statement of Limited Warranty

(a) Red Lion Controls Inc., Sixnet Inc., N-Tron Corporation, or Blue Tree Wireless Data, Inc. (the “Company”) war-

rants that all Products shall be free from defects in material and workmanship under normal use for the period of

time provided in “Statement of Warranty Periods” (available at www.redlion.net) current at the time of shipment of

the Products (the “Warranty Period”). EXCEPT FOR THE ABOVE-STATED WARRANTY, COMPANY MAKES NO

WARRANTY WHATSOEVER WITH RESPECT TO THE PRODUCTS, INCLUDING ANY (A) WARRANTY OF

MERCHANTABILITY; (B) WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE; OR (C) WARRANTY

AGAINST INFRINGEMENT OF INTELLECTUAL PROPERTY RIGHTS OF A THIRD PARTY; WHETHER

EXPRESS OR IMPLIED BY LAW, COURSE OF DEALING, COURSE OF PERFORMANCE, USAGE OF TRADE

OR OTHERWISE. Customer shall be responsible for determining that a Product is suitable for Customer's use and

that such use complies with any applicable local, state or federal law.

(b) The Company shall not be liable for a breach of the warranty set forth in paragraph (a) if (i) the defect is a result

of Customer's failure to store, install, commission or maintain the Product according to specifications; (ii) Customer

alters or repairs such Product without the prior written consent of Company.

sole discretion, either (i) repair or replace the Product; or (ii) credit or refund the price of Product provided that, if

Company so requests, Customer shall, at Company's expense, return such Product to Company.

(d) THE REMEDIES SET FORTH IN PARAGRAPH (c) SHALL BE THE CUSTOMER'S SOLE AND EXCLUSIVE

REMEDY AND COMPANY'S ENTIRE LIABILITY FOR ANY BREACH OF THE LIMITED WARRANTY SET

FORTH IN PARAGRAPH (a).

x Sixnet

Series RAM

9000 Hardware Guide

Revised 2016-02-12 Statement of Limited Warranty

Sixnet

Series RAM

9000 Hardware Guide 1-1

Product Overview Revised 2016-02-12

RAM

9000 Cellular RTU Product Highlights

Chapter 1 Product Overview

Using a single web-based user interface, our cellular units simplify I/O, network and security configurations to inte-

grate complex hardware settings. This easy-to-manage configuration reduces the cost and complexity of deploying

and administering multiple devices at remote locations. Furthermore, an integrated configurable stateful firewall

provides intrusion protection and encrypted data access while a built-in Software Development Kit (SDK) enables

users to develop custom applications.

Working in conjunction with SixView Manager remote monitoring and control software, RAM RTUs provide low-

cost, real-time access to outlying sites.

RAM

9000 Cellular RTU Product Highlights

• Supports Multi-Carrier 4G LTE connectivity with fall back to 3G (and 2G for non-EU/JP Models)

• Real-time access to mission-critical data through built-in Modbus gateway

• Software Development Kit (SDK) for custom application support

• Native support for DNP3 and Modbus protocols

• Integrated security firewall provides intrusion protection

• Simplified deployment and configuration with single web-based GUI

• Support for new and legacy devices with RS232/485 serial or RJ45 Ethernet

• Powerful event engine that can trigger built-in I/O, send SMS text or email alerts based on real-time operational

data.

Revised 2016-02-12 Product Overview

Specifications

1-2 Sixnet

Series RAM

9000 Hardware Guide

Specifications

General Specifications

Wireless Interfaces AT&T LTE with fallback to HSPA+ (non-EU/JP models)

Bell Mobility LTE with fallback to HSPA+

Generic LTE with fallback to HSPA+

Rogers LTE with fallback to HSPA+

TELUS LTE with fallback to HSPA+

Verizon LTE with fallback to EVDO (non-EU/JP models)

Programmable Platform Configurable Events: up to 99 events can be triggered by I/O, Modbus registers, or over 200

system variables which in turn can send text messages, send email alerts or control I/O

Software Development Kit (SDK)

C/C++/Perl

Protocol Gateway I/O Controller

Modbus RTU/TCP/ASCII

DNP3 - slave

System Performance 32-bit ARM9 400 MHz CPU

512 MB NAND Memory

128 MB RAM

Tunneling IPsec, GRE, OpenVPN

IP NAT, port forwarding, dynamic DNS, DHCP

Stateful inspection firewall, IP Transparency

Routing Protocols OSPF, BGP, RIP

Clustering VRRP

GPS GNSS supported: GPS L1, GLONASS L1, Galileo E1

High RF sensitivity plus jamming detection/removal

Connectors Ethernet: One (1) or two (2) 10/100Base-T RJ-45 ports

WAN capability on port 2

Serial: One (1) RS-232 (DB9) 115200bps

One (1) RS-485 (screw block)115200bps

USB: One (1) USB 2.0 (mini)

Antennas: Three (3) SMA connectors (antenna, diversity, GPS)

One (1) RP-SMA connector (Wi-Fi optional)

Sixnet

Series RAM

9000 Hardware Guide 1-3

Product Overview Revised 2016-02-12

Specifications

Inputs & Outputs 2 Digital Inputs

2 Digital Outputs

3 Analog Inputs

1 Form C Relay

See detailed I/O specifications in Section 1.2.5 below

Wi-Fi Interface

(Optional)

Complies with IEEE802.11b/g/n

Maximum output power up to 25dBm

Supports up to 150Mbps with 40MHz channel

Power Input Input: 12-24 VDC

Power consumption (less DO power):

• Standby: 4W (all models)

• Transmitting:

• 9911 & 9711: 5.0W - 9.4W (cellular only)

• 9931 & 9731: 5.0W - 13.6W (cellular and Wi-Fi)

Power consumption of DO (max each):

• 0.7A/DO

Heat dissipation: 46 BTU/hour max; 20 BTU/hour typical

Mechanical Dimensions: 132H x 127D x 70W mm (5.2” x 5.00” x 2.75”)

Material : Steel with black zinc coating

Weight: 906 g (2 lbs)

Environmental Operating temperature: -40°C to +75°C*

Shock: IEC60068-2-27

Vibration: IEC60068-2-6

Humidity: 5 to 95% non-condensing

Ingress Protection: IP30

Ethernet Interface

(10/100 Auto Sensing)

1x or 2x RJ45 (Isolation 1500 Vrms 1 minute)

WAN capability on 2

port

Serial interface 1x RS232 Serial DB9 115200bps

1x RS485 Serial Screws 115200bps (Isolation 1200 Vrms 1 minute)

USB interface 1x USB 2.0 Device mini

1x USB 2.0 Host type A

LED indicators Dual Power, Status Reset, WAN, RSSI, RS232, RS485, GPS, SD, Ethernet Link & Activity

Revised 2016-02-12 Product Overview

Specifications

1-4 Sixnet

Series RAM

9000 Hardware Guide

Certification EMI/EMC – Emissions: FCC, Part 15 and Industry Canada, ICES-003; Class A; EN55022,

IEC61000-6-4 Immunity: IEC61000-6-2 (EN61000-4-2,3,4,5,6,8)

Hazardous locations: Class I, Div. 2, Groups A, B, C, D, ANSI/ISA 12.12.01

Electrical safety: UL508/CSA22.2/14 (CUL): IEC61010-1

Carrier specific approvals (Contact Red Lion for latest)

RoHS compliant

ATEX

• Protection string: II 3 G Ex nA IIC T3 Gc

• ATEX Certificate string: DEMKO 15 ATEX 1366X

• Ambient temperature ranges:

• -40°C < Tamb < 75°C for units utilizing Panasonic BR-1225A

• -40°C < Tamb < 55°C for units utilizing Rayovac BR1225X-BA

• Conductor temperature of at least 107°C

• Battery Replacement info: Replace w/ Panasonic BR1225A or Rayovac BR1225X-

BA based on operating temperature given above.

• Standards evaluated for ATEX: IEC 60079-0 6

Edition, IEC 60079-15 4

Edition,

EN 60079-0:2012 + A11:2013, and EN 60079-15:2010

• The equipment shall be installed in an ATEX-Certified enclosure that provides a

degree of

protection not less than IP54 in accordance with EN/IEC 60079-15 and

used in an environment of not more than Pollution Degree 2 in accordance with EN/

IEC60664-1 when applied in Zone 2 environments. The enclosure must be

accessible only by the use of a tool.

• Conditions of Safe Use: Provision shall be made to prevent the rated voltage being

exceeded by the transient disturbances of more than 140% of the peak rated

voltage

• Special Conditions of Use: Antenna Connections are for internal wiring only.

•

Compliances The Red Lion Sixnet Series RAM 9000 products meet the following standards plus others:

Electrical Safety

These devices have been designed to meet the basic safety requirements of the following

standards:

• CE per Low Voltage Directive and IEC 61010-1 (CE applies only to the -EU

models. Please contact Red Lion for availability)

• UL508 (Industrial control equipment), ANSI/ISA 12.12.01 (Hazardous Locations)

• CSA C22.2 No. 142 and No. 213 (per cUL)

Sixnet

Series RAM

9000 Hardware Guide 1-5

Product Overview Revised 2016-02-12

Specifications

*-40°C to +75°C - See Thermal Performance and Considerations section in Chapter 2.

Note: All specifications are subject to change. Consult the Red Lion website for more information.

EMC (emissions and immunity)

• CE per the EMC directive (CE applies only to the -EU models. Please contact Red

Lion for availability)

• IEC 61000-6-2: Immunity in industrial environments

• IEC 61000-6-4: Emmissions in industrial environments

• FCC part 15 and ICES 003. See FCC statement on page 6.

• EN 55022 (CISPR22)

This equipment has been tested and found to comply with the limits for a Class A digital

device, pursuant to part 15 of the FCC rules. These limits are designed to provide reason

able protection against harmful interference when the equipment is operated in a commer-

cial environment. This equipment generates, uses, and can radiate radio frequency energy;

and if not installed and used in accordance with the instructions, may cause harmful interfer

ence to radio communications. Operation of this equipment in a residential area is likely to

cause harmful interference to radio communications, in which case the user will be required

to correct the interference at their own expense. Warning: Changes or modifications to this

unit not expressly approved by the party responsible for compliance could void the user's

authority to operate the equipment.

Information to the user: If this equipment causes interference to radio or television recep-

tion, which can be determined by turning the equipment off and on, the user is encouraged

to try to correct the interference by one or more of the following measures: In order to meet

FCC emissions limits, this equipment must be used only with cables that comply with IEEE

802.3. If necessary, the user should consult the dealer or an experienced radio/television

technician for additional suggestions. The user may find the following booklet prepared by

the Federal Communications Commission helpful: “How to Identify and Resolve Radio-TV

Interference Problems”. This booklet is available from: U.S. Government Printing Office,

Washington, DC 20402, Stock No. 004-000-00345-4

WEEE compliance

These devices comply with the WEEE directive. Do not throw away these devices in the

standard trash. Contact Red Lion regarding proper disposal.

RoHS compliance

These devices comply with the RoHS directive and are considered lead and other hazard-

ous substance free.

Revised 2016-02-12 Product Overview

Specifications

1-6 Sixnet

Series RAM

9000 Hardware Guide

RAM 9000 Model Comparison Chart

Feature RAM-9x01 RAM-9x11 RAM-9x31

Cellular x = 6 for 3G (non-EU/JP models)

x = 7 for 4G LTE (non-EU/JP

models)

x = 9 for 4G LTE+ (EU/JP

models)

x = 6 for 3G (non-EU/JP models)

x = 7 for 4G LTE (non-EU/JP

models)

x = 9 for 4G LTE+ (EU/JP

models)

x = 6 for 3G (non-EU/JP models)

x = 7 for 4G LTE (non-EU/JP

models)

x = 9 for 4G LTE+ (EU/JP

Models)

Wi-Fi - - 1

GPS 1 1 1

Ethernet Port 1 2 2

RS232 Port 1 1 1

RS485 Port 1 1 1

USB Host Port 1 1 1

USB Device

Port

1 1 1

SIM Card Slot 2* 2* 2*

SD Card Slot 1 1 1

Discrete Input 2 2 2

Discrete Out-

put

2 2 2

Relay Output 1 1 1

Analog Input 3 3 3

* The second SIM slot is not currently active. This feature will be enabled in a future firmware release.

Contact Red Lion for availability of this feature.

Sixnet

Series RAM

9000 Hardware Guide 1-7

Product Overview Revised 2016-02-12

Specifications

RAM 9000 Cellular RTU View

RAM-9x01

RAM-9x11

RAM-9x31

Power Specifications and Consumption

Power Input:

• Input: 12-24 VDC (absolute min./max.: 8-30 VDC)

• Power consumption (less DO power):

• Idle: 4W

• Typical: 5 - 6 W

• Maximum: 6 - 14 W (depends on model)

• Power consumption of DO (max. each):

• 0.7A/DO

• Heat dissipation: 46 BTU/hour max.; 20 BTU/hour typical

Power input to the unit is protected against reverse polarity and over-voltage up to 33VDC. The router’s power con-

sumption is as follows:

Typical Power Consumption (Watts)

Model Standby

Transmitting

Minimum

Transmitting

Maximum

Geographic

Region

RAM-99x1 4.0 5.0 9.4 Non-EU

RAM-99x1-EU 4.0 5.0 9.4 EU

RAM-99x1-JP 4.0 5.0 9.4 JP

Revised 2016-02-12 Product Overview

Specifications

1-8 Sixnet

Series RAM

9000 Hardware Guide

Note: Wiring instructions are provided in I/O Wiring section in Chapter 2 of this guide.

Electrical Specifications and Pinout

Discrete Inputs:

• 2 Channels

• Isolated fully differential

• Isolation (channel to channel) = 1 KV

• Voltage range = 8-30 VDC

• Guaranteed ON voltage = 2.8 VDC

• Guaranteed OFF voltage = 2.7 VDC

• Input resistance = 315K Ohms

• Input current @ 24 VDC = 10 mA

• Filtered ON/OFF delay = 25 ms (10 Hz max count rate)

• Count resolution = 16 or 32 bits

Discrete Outputs:

• 2 Channels

• Sourcing of module power

• Max. output load per channel = 1 A (up to 35°C)

RAM-97x1 4.0 5.0 9.4 Non-EU

RAM-96x1 4.0 4.6 5.5 Non-EU

RAM-9931 4.0 5.0 13.6 Non-EU

RAM-9931-EU 4.0 5.0 13.6 EU

RAM-9931-JP 4.0 5.0 13.6 JP

RAM-9731 4.0 5.0 13.6 Non-EU

RAM-9631 4.0 4.6 9.7 Non-EU

To meet UL requirements, a “Class 2 Source” power supply is required.

Typical Power Consumption (Watts)

Model Standby

Transmitting

Minimum

Transmitting

Maximum

Geographic

Region

La page charge ...

Sixnet RAM 9000 Hardware Guide d'installation

Marque: Sixnet

Modèle: RAM 9000 Hardware

Taper: Guide d'installation

Télécharger le PDF

rapport

dans d''autres langues

English: Sixnet RAM 9000 Hardware Installation guide

Sixnet RAM 9000 Hardware Guide d'installation

Sixnet RAM 9000 Hardware Guide d'installation

dans d''autres langues

Documents connexes

Autres documents