Eizo FDSV1201 Manuel utilisateur

Important

Please read this User’s Manual, and the Setup Manual (separate

volume) carefully to familiarize yourself with safe and effective usage.

• Please refer to the Setup Manual for basic information ranging from

connection of the monitor to a PC to using the monitor.

• The latest User’s Manual is available for download from our web site:

http://www.eizoglobal.com

2



This product has been adjusted specically for use in the region to which it was originally shipped. If operated

outside this region, the product may not perform as stated in the specications.

No part of this manual may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means,

electronic, mechanical, or otherwise, without the prior written permission of EIZO Corporation.

EIZO Corporation is under no obligation to hold any submitted material or information condential unless prior

arrangements are made pursuant to EIZO Corporation’s receipt of said information. Although every effort has been

made to ensure that this manual provides up-to-date information, please note that EIZO monitor specications are

subject to change without notice.

3

Noticeforthismonitor

Notice for this monitor

Aside from creating documents, viewing multimedia content, and other general purposes, this product is also suited to

the dedicated usages such as operation of terminal equipment.

This product has been adjusted specically for use in the region to which it was originally shipped. If the product is

used outside the region, it may not operate as specied in the specications.

This product may not be covered by warranty for uses other than those described in this manual.

The specications noted in this manual are only applicable when the following are used:

· Signal cables specied by us

Only use optional products manufactured or specied by us with this product.

If you place this product on a lacquer-coated desk, the color may adhere to the bottom of the stand due to the

composition of the rubber. Check the desk surface before use.

It takes about 30 minutes for the performance of electrical parts to stabilize. Please wait 30 minutes or more after the

monitor power has been turned on, and then adjust the monitor.

Monitors should be set to a lower brightness to reduce changes in luminosity caused by long-term use and maintain a

stable display.

When the screen image is changed after displaying the same image for extended periods of time, an afterimage may

appear. Use the screen saver or power save function to avoid displaying the same image for extended periods of time.

Periodic cleaning is recommended to keep the monitor looking new and to prolong its operation lifetime (refer to

“Cleaning” (page 4)).

The LCD panel is manufactured using high-precision technology. Although, missing pixels or lit pixels may appear on

the LCD panel, this is not a malfunction. Percentage of effective dots: 99.9994% or higher.

The backlight of the LCD panel has a xed lifetime. When the screen becomes dark or begins to icker, please contact

your local EIZO representative.

Do not scratch or press on the panel with any sharp objects, as this may result in damage to the panel. Do not attempt

to brush with tissues as this may scratch the panel.

When the monitor is cold and brought into a room or the room temperature goes up quickly, dew condensation may

occur on the interior and exterior surfaces of the monitor. In that case, do not turn the monitor on. Instead wait until

the dew condensation disappears, otherwise it may cause some damage to the monitor.

(Cautions for the Use of the Touch Panel)

• During touch operation

Be careful of the following points. Otherwise, damage may occur to the monitor.

- Do not strongly press, scratch, or poke the panel.

- Do not touch the panel with hard objects such as ballpoint pens or metals.

4

Noticeforthismonitor

Cleaning

Attention

• Chemicals such as alcohol and antiseptic solution may cause gloss variation, tarnishing, and fading of the cabinet or panel,

and also quality deterioration of the image.

• Never use any thinner, benzene, wax, and abrasive cleaner, which may damage the cabinet or panel.

• Do not allow liquid to enter the clearance between the panel and the panel frame.

Note

• The optional ScreenCleaner is recommended for cleaning the cabinet and panel surface.

The stains on the cabinet and panel surface can be removed by moistening part of a soft cloth with water.

To use the monitor comfortably

• An excessively dark or bright screen may affect your eyes. Adjust the brightness of the monitor according to

the environmental conditions.

• Staring at the monitor for a long time tires your eyes. Take a 10-minute rest every hour.

5

CONTENTS

Notice for this monitor ......................................... 3

Cleaning .................................................................... 4

To use the monitor comfortably ............................. 4

CONTENTS ............................................................. 5

Chapter 1 Introduction ....................................... 6

1-1. Features ......................................................... 6

1-2. EIZO LCD Utility Disk.................................... 7

●

Diskcontentsandsoftwareoverview............. 7

●

Tousetouchpaneldriver............................... 7

1-3. Basic Operations and Functions ................ 8

●

BasicoperationoftheSettingmenu............... 8

●

Functions......................................................... 9

Chapter 2 Adjusting Screens .......................... 10

2-1. Setting the Resolution ................................10

●

Displayresolution...........................................10

●

Settingresolution...........................................10

2-2. Adjusting Color ............................................11

●

Toselectthedisplaymode(ColorMode).......11

●

Toperformadvancedadjustments................11

●

Adjustablesettingsineachmode..................12

●

Toadjustbrightness.......................................12

●

Toadjustcolortemperature...........................13

●

Toadjustgamma...........................................13

●

Toadjustthecolorsaturation.........................14

●

Toadjusthue..................................................14

●

Toadjustgain.................................................15

2-3. Screen Adjustment ......................................16

●

DigitalSignalInput.........................................16

●

AnalogSignalInput........................................16

Chapter 3 Setting Monitor ............................... 20

3-1. Setting the Orientation ............................... 20

3-2. Enabling / Disabling DDC/CI

communication .......................................... 20

3-3. Locking Operation Buttons ....................... 20

3-4. Showing and hiding the EIZO logo ........... 20

3-5. Setting Language .........................................21

3-6. Resetting the Monitor to the Default

Settings .........................................................21

●

Toresetthecoloradjustments.......................21

●

Toresetalladjustmentstothedefault

settings...........................................................21

Chapter 4 Power Saving Functions ................ 22

4-1. Setting Power Saving ................................. 22

4-2. Setting Power Indicator .............................. 22

4-3. Enabling / Disabling Auto Power-OFF ...... 23

Chapter 5 Troubleshooting .............................. 24

5-1. No picture .................................................... 24

5-2. Imaging problems (for both digital and

analog) .......................................................... 25

5-3. Imaging problems (for analog only) ......... 25

5-4. Other problems ........................................... 26

5-5. Touch panel problems (for FDSV1201T

only) .............................................................. 26

Chapter 6 Reference ........................................ 27

6-1. Attaching the Optional Arm ....................... 27

6-2. Connecting Multiple PCs ........................... 28

●

Toswitchamonginputsignals...................... 28

●

Tosetinputsignalselection.......................... 29

6-3. Displaying Monitor Information ................ 29

6-4. Specications ............................................. 30

●

MainDefaultSettings.................................... 32

●

OutsideDimensions...................................... 32

6-5. Preset Timing .............................................. 33

Chapter 7 Glossary .......................................... 34

Appendix .............................................................. 36

Trademark ............................................................... 36

License / Copyright ................................................ 36

FCC Declaration of Conformity .............................37

LIMITED WARRANTY ............................................. 38

Recycling Information ............................................47

China Measures for RoHS Compliance in

ChinaRoHS ...............................................................51

6

Chapter1Introduction

Chapter 1 Introduction

Thank you very much for choosing an EIZO color LCD monitor.

1-1. Features

• 12.1″ LCD

• Supports a resolution of 800 × 600

• Maximum brightness

FDSV1201: 450cd/m

2

, FDSV1201T: 360cd/m

2

• Display at low brightness

*1

*1 0.1% of maximum brightness (typ.)

• LED backlight LCD panel

No mercury, a hazardous substance, is used.

• Operation lock function

The operation of buttons other than the power button can be locked to prevent accidental operation.

See “3-3. Locking Operation Buttons” (page 20).

• Power saving function

Suppressing the power consumption reduces the carbon dioxide emissions. This product is equipped with power saving

function.

- Eco Timer

This function allows you to set the monitor to turn off automatically after a specied time has passed in the power

saving mode.

See “4-3. Enabling / Disabling Auto Power-OFF” (page 23).

• Displays HDCP (High-bandwidth Digital Protection) protected contents

(for FDSV1201T only)

• Touch Panel provided

- Detection method: Analog resistive technology

- Supported OS: Microsoft Windows 10 (32 bit/64 bit)

Microsoft Windows 8.1 (32 bit/64 bit)

Microsoft Windows 7 Service Pack 1 (32 bit/64 bit)

Microsoft Windows Vista Service Pack 2 (32 bit)

Microsoft Windows XP Service Pack 3 (32 bit)

- Communication: USB, RS-232C (* Cannot be used at the same time.)

7

Chapter1Introduction

1-2. EIZO LCD Utility Disk

An “EIZO LCD Utility Disk” (CD-ROM) is supplied with this product. The following table shows the disk contents

and the overview of the software programs.

●

Disk contents and software overview

The disk includes adjustment software, touch panel software, and user’s manuals. Refer to Readme.txt le on

the disk for software startup procedures or le access procedures.

Item Overview Windows Macintosh

Screenadjustmentpatternles Usedwhenadjustingtheimageofanalog

signalinputmanually.

√ √

Touchpaneldriver

*1

Driversoftwarerequiredforoperatingthe

touchpanelmonitoronWindows.

√ -

User’sManualofthismonitor(PDFle) √ √

User’sManualforTouchPanelDriver(PDFle)

*1

√ -

Readme.txtle √ √

*1 Used only for the FDSV1201T.

●

To use touch panel driver

For information on how to install or use the touch panel driver, see the Touch Panel Driver User’s Manual (on

the CD-ROM).

8

Chapter1Introduction

1-3. Basic Operations and Functions

●

Basic operation of the Setting menu

1.

Displaying the Setting menu

1. Press . The Setting menu appears.

2.

Adjusting / Setting

1. Choose a menu to adjust / set with , , and then press . The Sub menu appears.

2. Choose an item to adjust / set with , , and then press . The adjustment / setting menu appears.

3. Adjust / set the selected item with , , and then press .

3.

Exiting

1. Choose “Return” from the Sub menu and press . The Setting menu appears.

2. Choose “Exit” from the Main menu and press

. The Setting menu quits.

Note

•

The Setting menu can also be exited by pressing

twice quickly.

9

Chapter1Introduction

●

Functions

The following table shows the Setting menu and setting items of each menu.

Main menu Setting Reference

Color

*1

Brightness “2-2.AdjustingColor”(page11)

Temperature

Gamma

AdvancedSettings Saturation

Hue

Gain

ColorReset “Toresetthecoloradjustments”(page21)

Screen Smoothing “2-3.ScreenAdjustment”(page16)

AnalogAdjustment

*2

AutoScreenAdjust

AutoRangeAdjust

Clock

Phase

Hor.Position

Ver.Position

PowerManager PowerSave “4-1.SettingPowerSaving”(page22)

EcoTimer “4-3.Enabling/DisablingAutoPower-OFF”

(page23)

MonitorSettings InputSignal “Tosetinputsignalselection”(page29)

PowerIndicator “4-2.SettingPowerIndicator”(page22)

Language “3-5.SettingLanguage”(page21)

DDC/CI “3-2.Enabling/DisablingDDC/CI

communication”(page20)

Logo “3-4.ShowingandhidingtheEIZOlogo”

(page20)

Reset “Toresetalladjustmentstothedefault

settings”(page21)

Information “6-3.DisplayingMonitorInformation”(page29)

*1 The adjustment / settings available on the “Color” menu depend on the selected Color mode (see “Adjustable

settings in each mode” (page 12)).

*2 These functions can be adjusted with analog input.

10

Chapter2AdjustingScreens

Chapter 2 Adjusting Screens

2-1. Setting the Resolution

●

Display resolution

For details on compatible resolutions, refer to “Compatible Resolutions” in the Setup Manual.

●

Setting resolution

When you connect the monitor to the PC and nd that the resolution is improper, or when you want to change

the resolution, follow the procedure below.

Windows 10

1. Right-click the mouse anywhere on the desktop except for icons.

2. From the displayed menu, click “Display Settings”.

3. On the “Customize your display” dialog box, click “Advanced display settings”.

4. Select a monitor, then choose a resolution from the “Resolution” pull-down menu.

5. Click the “Apply” button.

6. When a conrmation dialog box is displayed, click “Keep changes”.

Windows 8.1 / Windows 7

1. For Windows 8.1, click the “Desktop” tile on the Start Screen to display the desktop.

2. Right-click the mouse anywhere on the desktop except for icons.

3. From the displayed menu, click “Screen resolution”.

4. On the “Screen Resolution” dialog box, select the monitor.

5. Click “Resolution” to select the desired resolution.

6. Click the “OK” button.

7. When a conrmation dialog box is displayed, click “Keep changes”.

Windows Vista

1. Right-click the mouse anywhere on the desktop except for icons.

2. From the displayed menu, click “Personalize”.

3. On the “Personalization” window, click “Display Settings”.

4. On the “Display Settings” dialog box, select the “Monitor” tab and select desired resolution in the

“Resolution” eld.

5. Click the “OK” button.

6. When a conrmation dialog box is displayed, click “Yes”.

Windows XP

1. Right-click the mouse anywhere on the desktop except for icons.

2. From the displayed menu, click “Properties”.

3. When the “Display Properties” dialog box is displayed, click the “Settings” tab and select desired resolution

for “Screen resolution” under “Display”.

4. Click the “OK” button to close the dialog box.

11

Chapter2AdjustingScreens

Mac OS X

1. Select “System Preferences” from the Apple menu.

2. When the “System Preferences” dialog box is displayed, click “Displays” for “Hardware”.

3. On the displayed dialog box, select the “Display” tab and select desired resolution in the “Resolutions” eld.

4. Your selection will be reected immediately. When you are satised with the selected resolution, close the

window.

2-2. Adjusting Color

●

To select the display mode (Color Mode)

This function allows easy selection of a desired mode according to monitor application.

Display Modes

Mode Purpose

User1 Selectthistodeneadesiredsetofparametersettings.

User2

sRGB SuitableforcolormatchingwithsRGBcompatibleperipherals.

Themodemenu

appears.

Procedure

1. Press

.

The mode menu appears at the bottom left of the screen.

2. The mode among the list is highlighted in turn each time is pressed.

You can switch the mode with or while the mode menu is displayed.

User1←→User2←→sRGB

Note

• The Setting menu and the Mode menu cannot be displayed at the same time.

●

To perform advanced adjustments

The “Color” menu of the Setting menu allows you to set and save the independent color adjustment for each

mode.

Attention

• It takes about 30 minutes for the performance of electrical parts to stabilize. Please wait 30 minutes or more after the

monitor power has been turned on, and then adjust the monitor.

• Perform the range adjustment rst when adjusting color for analog signals (see “To adjust color gradation automatically”

(page 19)).

• The same image may be seen in different colors on multiple monitors due to their monitor-specic characteristics. Make

ne color adjustment visually when matching colors on multiple monitors.

12

Chapter2AdjustingScreens

●

Adjustable settings in each mode

The adjustable settings depend on the mode. (Non-adjustable or non-settable function cannot be selected.)

√: Adjustable -: Not adjustable

Function

Color Mode

User1 User2 sRGB

Brightness √ √ √

Temperature √ √ -

Gamma √ √ -

AdvancedSettings Saturation √ √ -

Hue √ √ -

Gain √ √ -

ColorReset √ √ √

●

To adjust brightness

The screen brightness is adjusted by changing the brightness of the backlight (light source from the LCD back

panel).

Adjustable range

0 to 100

Procedure

1. Press

.

The brightness adjustment screen appears.

2. Use or for adjustment.

3. Press

to exit.

Attention

• A range of setting values on the adjustment screen are displayed in magenta. The contrast (video signal level) is changed

to adjust the brightness in this range.

Note

• Alternatively, you can use “Brightness” under “Color” in the Adjustment menu to adjust it.

13

Chapter2AdjustingScreens

●

To adjust color temperature

Color temperature can be adjusted.

The color temperature is normally used to express the hue of “White” and / or “Black” by a numerical value.

The value is expressed in degrees “K” (Kelvin).

The screen becomes reddish at a low color temperature, and bluish at a high color temperature, like the ame

temperature. A gain preset value is set for each color temperature setting value.

Adjustable range

Off, 4000 K-10000 K (specied by every 500 K unit, including 9300 K)

Procedure

1. Choose “Color” in the Setting menu, and press

.

2. Choose “Temperature” in the “Color” menu, and press

.

The “Temperature” menu appears.

3. Use or for adjustment.

4. Press

to exit.

Note

• The value shown in “K” is available only as reference.

• “Gain” allows you to perform more advanced adjustment (see “To adjust gain” (page 15)).

• If you set to “Off”, the image is displayed in the preset color of the monitor (Gain: 100 for each RGB).

• When gain is changed, the color temperature is changed to “Off”.

●

To adjust gamma

Gamma can be adjusted. The brightness of the monitor varies depending on the input signal, however, the

variation rate is not proportional to the input signal. To keep the balance between the input signal and the

brightness of the monitor is called as “Gamma correction”.

Adjustable range

1.8, 2.0, 2.2

Procedure

1. Choose “Color” in the Setting menu, and press

.

2. Choose “Gamma” in the “Color” menu, and press

.

The “Gamma” menu appears.

3. Use or for adjustment.

4. Press

to exit.

14

Chapter2AdjustingScreens

●

To adjust the color saturation

This function allows you to adjust color saturation.

Adjustable range

-50 to 50

Procedure

1. Choose “Color” in the Setting menu, and press

.

2. Choose “Advanced Settings” in the “Color” menu, and press

.

3. Choose “Saturation” in the “Advanced Settings” menu, and press

.

The “Saturation” menu appears.

4. Use or for adjustment.

5. Press

to exit.

Attention

• Using this function may make some color gradations unavailable for display.

Note

• The minimum value (-50) changes the screen to monochrome.

●

To adjust hue

This function allows you to adjust hue.

Adjustable range

-50 to 50

Procedure

1. Choose “Color” in the Setting menu, and press

.

2. Choose “Advanced Settings” in the “Color” menu, and press

.

3. Choose “Hue” in the “Advanced Settings” menu, and press

.

The “Hue” menu appears.

4. Use or for adjustment.

5. Press

to exit.

Attention

• Using this function may make some color gradations unavailable for display.

15

Chapter2AdjustingScreens

●

To adjust gain

The brightness of each color component red, green, and blue is called “Gain”. You can change the hue of

“white” by adjusting gain.

Adjustable range

0 to 100

Procedure

1. Choose “Color” in the Setting menu, and press

.

2. Choose “Advanced Settings” in the “Color” menu, and press

.

3. Choose “Gain” in the “Advanced Settings” menu, and press

.

The “Gain” menu appears.

4. Adjust gain with or for each of red, green, and blue.

5. Press

to exit.

Attention

• Using this function may make some color gradations unavailable for display.

Note

• The value of gain changes with that of color temperature.

• When gain is changed, the color temperature is changed to “Off”.

16

Chapter2AdjustingScreens

2-3. Screen Adjustment

●

Digital Signal Input

When digital signals are input, images are displayed correctly based on the preset data of the monitor, but if

characters and / or lines appear blurred, go to “To modify blurred characters / lines” (page 19).

When performing more advanced adjustment, see “2-2. Adjusting Color” (page 11) and subsequent pages.

●

Analog Signal Input

Attention

• It takes about 30 minutes for the performance of electrical parts to stabilize. Please wait 30 minutes or more after the

monitor power has been turned on, and then adjust the monitor.

• The Self Adjust (automatic screen adjustment) function does not work for the images under the resolution of 800 × 600

(SVGA).

• The self adjustment (or automatic screen adjustment) function works correctly when an image is fully displayed over the

Windows or Macintosh display area. They do not work properly in the cases below:

- When an image is displayed only on a part of the screen (command prompt window, for example)

- When a black background (wallpaper, etc.) is in use

Also, these functions cannot work properly in some graphic boards.

The monitor screen adjustment is used to suppress ickering of the screen or adjust screen position and screen

size correctly according to the PC to be used.

Note

• The Self Adjust function works when all of the following conditions are satised:

- When a signal is input into the monitor for the rst time or when a resolution or vertical / horizontal scan frequency

not used before is set

If the screen is not displayed correctly even after performing the Self Adjust operation, adjust the screen

according to the procedures on the following pages to use the monitor comfortably.

Setting Procedures

1.

Perform the auto adjustment.

●

To adjust ickering, screen position, and screen size automatically

Procedure

1. Choose “Screen” in the Setting menu, and press

.

2. Choose “Analog Adjustment” in the “Screen” menu, and press

.

3. Choose “Auto Screen Adjust” in the “Analog Adjustment” menu, and press

.

4. Select “Yes” with

or , and press .

Flickering, screen position, and screen size are corrected by the auto-adjustment function.

Ifthescreenisnotdisplayedcorrectlyevenafterperformingtheautoadjustment,performadjustments

accordingtothefollowingprocedure.Ifthescreenisdisplayedcorrectly,goto“5.Adjustingcolorgradation.”

(page19).

17

Chapter2AdjustingScreens

2.

Prepare to use analog screen adjustment patterns.

Load the “EIZO LCD Utility Disk” to your PC, and then open the “Screen adjustment pattern les”.

Note

• For details and instructions on opening the “Screen adjustment pattern les”, refer to the Readme.txt le.

3.

Perform the auto adjustment again with the analog screen adjustment pattern

displayed.

●

To adjust ickering, screen position, and screen size automatically

Procedure

1. Display Pattern 1 in full screen on the monitor using the “Screen adjustment pattern les”.

2. Choose “Screen” in the Setting menu, and press .

3. Choose “Analog Adjustment” in the “Screen” menu, and press

.

4. Choose “Auto Screen Adjust” in the “Analog Adjustment” menu, and press

.

5. Select “Yes” with

or , and press .

Flickering, screen position, and screen size are corrected by the auto-adjustment function.

Ifthescreenisnotdisplayedcorrectlyevenafterperformingtheautoadjustment,performadjustments

accordingtothefollowingprocedure.Ifthescreenisdisplayedcorrectly,goto“5.Adjustingcolorgradation.”

(page19).

4.

Choose “Screen” from the Setting menu to perform advanced adjustments.

Adjust the clock, phase and position, in this order.

●

To eliminate vertical bars

Procedure

1. Choose “Analog Adjustment” in the “Screen” menu, and press

.

2. Choose “Clock” in the “Analog Adjustment” menu, and press

.

The “Clock” menu appears.

3. Adjust the clock with or to eliminate vertical bars.

Press or slowly so as not to miss the adjustment point.

4. Press to exit.

When blurring, ickering or bars appear on the screen after adjustment, proceed to “To remove ickering or blurring ”.

18

Chapter2AdjustingScreens

●

To remove ickering or blurring

Procedure

1. Choose “Analog Adjustment” in the “Screen” menu, and press

.

2. Choose “Phase” in the “Analog Adjustment” menu, and press

.

The “Phase” menu appears.

3. Adjust the phase with or to minimize ickering or blurring.

4. Press

to exit.

When vertical bars appear on the screen after adjustment, go back to “To eliminate vertical bars ”.

(Clock → Phase → Position)

Attention

• Flickering or blurring may not be eliminated depending on your PC or graphics board.

●

To correct the screen position

Note

• Since the number of pixels and the pixel positions are xed on the LCD monitor, only one position is provided to display

images correctly. The position adjustment is made to shift an image to the correct position.

Procedure

1. Choose “Analog Adjustment” in the “Screen” menu, and press

.

2. Choose “Hor.Position” or “Ver.Position” from the “Analog Adjustment” menu, and press

.

The “Hor. Position” or “Ver. Position” menu appears.

3. Adjust the position with or .

4. Press

to exit.

5. Close Pattern 1.

19

Chapter2AdjustingScreens

5.

Adjusting color gradation.

●

To adjust color gradation automatically

Every color gradation (0 to 255) can be displayed by adjusting the signal output level.

Procedure

1. Display Pattern 2 in full screen on the monitor using the “Screen adjustment pattern les”.

2. Choose “Screen” in the Setting menu, and press .

3. Choose “Analog Adjustment” in the “Screen” menu, and press

.

4. Choose “Auto Range Adjust” in the “Analog Adjustment” menu, and press

.

5. Select “Yes” with

or , and press .

The output range is set automatically.

6. Close Pattern 2.

6.

Modify blurred characters or lines.

●

To modify blurred characters / lines

When an image is displayed with a resolution other than recommended, the characters or lines of the

displayed image may blur.

Attention

• Smoothing setting may not be required depending on the display resolution. (You cannot choose the smoothing icon.)

Adjustable range

1 to 5

Procedure

1. Choose “Screen” in the Setting menu, and press

.

2. Choose “Smoothing” in the “Screen” menu, and press

.

The “Smoothing” menu appears.

3. Use or for adjustment.

4. Press

to exit.

20

Chapter3SettingMonitor

Chapter 3 Setting Monitor

3-1. Setting the Orientation

The image can be ipped vertically (rotated 180 degrees) to match the orientation of the monitor.

Procedure

1. Press

to turn off the monitor.

2. Hold down

while pressing to turn on the monitor.

The image is ipped vertically each time this operation is performed.

3-2. Enabling / Disabling DDC/CI communication

This function allows you to enable / disable the DDC/CI communication (see “Chapter 7 Glossary” (page 34)).

Procedure

1. Choose “Monitor Settings” in the Setting menu, and press

.

2. Choose “DDC/CI” in the “Monitor Settings” menu, and press

.

The “DDC/CI” menu appears.

3. Select “On” or “Off” with or .

4. Press

to exit.

3-3. Locking Operation Buttons

This function allows you to lock the settings to prevent them being changed.

Procedure

1. Press

to turn off the monitor.

2. Hold down

while pressing to turn on the monitor.

You can toggle between Lock and Unlock by performing steps 1 and 2.

Note

• The following operations are available even if the buttons are locked:

- Turning on or off the monitor with the Power button

3-4. Showing and hiding the EIZO logo

When the monitor is turned on, the EIZO logo appears on the screen. You can choose to show or hide the display of

the EIZO logo.

Procedure

1. Choose “Monitor Settings” in the Setting menu, and press

.

2. Choose “Menu Settings” in the “Monitor Settings” menu, and press

.

3. Choose “Logo” in the “Menu Settings” menu, and press

.

The “Logo” menu appears.

4. Select “On” or “Off” with or .

5. Press

to exit.

La page charge ...

Eizo FDSV1201 Manuel utilisateur

Ce manuel convient également à

Eizo FDSV1201 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents