Tripp Lite SMART700HGL & SMART1200XLHGL Le manuel du propriétaire
- Catégorie
- Alimentations sans interruption (UPS)
- Taper
- Le manuel du propriétaire
1
Owner’s Manual
SmartPro
®
Medical-Grade UPS Systems
(with Lithium Iron Phosphate Batteries)
Models:
Important Safety Instructions 2
Package Contents 5
Connecting the Batteries 6
Quick Installation 7
Basic Operation 9
Guidance and Manufacturer’s Declaration 12
Storage and Service 13
Regulatory Compliance and 14
Product Registration
Español 15
Français 30
1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support
Copyright © 2016 Tripp Lite. All rights reserved.
SMART700HGL
(Series Number: AG-8863)
SMART1200XLHGL
(Series Number: AG-8862)
PROTECT YOUR INVESTMENT!
Register your product for quicker service
and ultimate peace of mind.
You could also win an
ISOBAR6ULTRA surge protector—
a $100 value!
www.tripplite.com/warranty
16-07-004-933608.indb 1 8/31/2016 9:59:30 AM
2
Important Safety Instructions
SAVE THESE INSTRUCTIONS
This manual contains instructions and warnings that should be followed during the installation,
operation and storage of all Tripp Lite UPS Systems. Failure to heed these warnings may affect
your warranty.
Statement of Intended Use
Tripp Lite Medical-Grade UPS Systems are intended to support and protect non-medical and
medical computer equipment and medical devices that require leakage current reduction, surge
protection, voltage regulation, line noise filtering and battery backup during power outages and
generator testing, both inside and outside patient care areas. Tripp Lite Medical-Grade UPS Systems
come with hospital-grade plugs and receptacles that reduce leakage to below 100μA.
Product Information
SMART700HGL SMART1200XLHGL
AC Input Voltage 120 120
AC Input Voltage Range 81–143 81–143
Input Amp(s) 5.5 9.2
Output Amp 5.8 6.25
Rated Power (VA/Watts) 700VA/450W 1000VA/750W
Frequency 60 Hz 60 Hz
No. of Phases Single Single
Class Type Class I Class I
Plug/Connector Type NEMA 5-15P NEMA 5-15P
Operation Continuous Continuous
AC Input Protection (Qty./type/rating) Input breaker
(2 x 10A), thermal
Input breaker
(2 x 15A), thermal
Max Leakage Current (uA) Less than 100uA Less than 100uA
Weight 33.7 lb. (15.3 kg) 33.6 lb. (15.2 kg)
Known Contraindication None None
UPS Location Warnings
Relevant Symbols
Denotes that information in the manual should be reviewed before use.
Used to signal a warning that a statement is particularly important and could pose a safety
risk.
Warning—Dangerous Voltage No sitting
Denotes general warning sign No stepping on surface
Refer to Instruction Manual/Booklet No pushing
16-07-004-933608.indb 2 8/31/2016 9:59:31 AM
3
Important Safety Instructions continued
• Do not use this equipment within oxygen-enriched atmospheres, or within 1 ft. (0.3 m) of a point
at which an oxygen-enriched atmosphere is intentionally vented.
• Use caution when lifting UPS. Because of the considerable weight of all UPS systems, at least
two people should assist in lifting and installing them.
• Install the UPS indoors, away from excess moisture or heat, dust or direct sunlight.
• For best performance, the UPS should be used in a location that meets the following conditions:
Temperature: 32 to 104° F (0 to 40° C); Humidity: 0 to 95% (non-condensing);
Elevation: <6,562 ft. (2,000 m) above sea level.
• Leave adequate space around all sides of the UPS for proper ventilation. Do not obstruct its vents
or fan openings.
• Do not mount unit with its front or rear panel facing down (at any angle). Mounting in this manner
will seriously inhibit the unit’s internal cooling, eventually causing product damage not covered
under warranty.
• UPS is not intended for patient contact. Avoid installation that will cause accidental patient
contact.
UPS Connection Warnings
• The UPS contains its own energy source (battery). The output terminals may be live even when
the UPS is not connected to an AC supply.
• Connect the UPS to a properly grounded AC power outlet. Do not modify the UPS plug in a
way that would eliminate its connection to ground. Do not use adapters that eliminate the UPS
connection to ground.
• Do not plug the UPS into itself; this will damage the UPS and void your warranty.
• If connecting the UPS to a motor-powered AC generator, the generator must provide filtered,
frequency-regulated output.
• To remove the UPS from the supply mains, the plug serves as a disconnect device.
• Once connected, do not limit access to the input plug. The plug must be accessible to be used as
a means of disconnection.
• When connecting the UPS to a power outlet, ensure the power outlet is provided with suitable
overcurrent protection in accordance with national and local electrical codes. Ensure the
overcurrent protection has a minimum of 1500A breaking capacity.
CAUTION: Do not remove cover for 5 minutes after disconnecting all sources of
supply. Risk of electric shock—hazardous live parts inside. Do not remove cover.
No user serviceable parts inside. Refer servicing to qualified service personnel.
This UPS receives power from more DC sources; disconnection of the AC and DC
source is required to de-energize the unit before servicing.
CAUTION: To ensure proper grounding with supply mains power, the input cord must
be connected with an approved country-specific plug with a protective earth ground
connection.
CAUTION: If this product is operated on battery (not connected to mains power),
adequate safeguards should be employed to protect against accidental contact
with AC power conductors.
CAUTION: Do not exceed total rated output.
WARNING: No modification of this equipment is allowed.
16-07-004-933608.indb 3 8/31/2016 9:59:31 AM
4
Important Safety Instructions continued
Equipment Connection Warnings
• Do not use Tripp Lite UPS Systems for life support applications in which a malfunction or failure of
a Tripp Lite UPS System could cause failure or significantly alter the performance of a life-support
device.
• The AC output is floating (the neutral output conductor is not grounded).
• Do not connect surge protectors or extension cords to the UPS output; doing so may damage the
UPS and affect the surge protector and UPS warranties.
CAUTION: The unit is for exclusive interconnection with IEC 60601-1 certified
equipment in the patient environment and IEC 60950-1 certified equipment outside
of the patient environment. Do not contact SIP/SOP (such as the USB port, RS-232
port, etc.) and the patient at the same time.
Battery Warnings
• Batteries can present a risk of electrical shock and burn from high short-circuit current. Observe
proper precautions. Do not dispose of the batteries in a fire. Do not open the UPS or batteries.
Do not short or bridge the battery terminals with any object. Unplug and turn off the UPS before
performing battery replacement. Use tools with insulated handles. There are no user-serviceable
parts inside the UPS. Battery replacement should be performed only by authorized service
personnel using the same number and type of batteries (lithium iron phosphate). The batteries
are recyclable. At the end of the UPS unit’s life, follow best practice by discharging the battery
prior to disposal. Refer to local codes for disposal requirements. Tripp Lite offers a complete
line of UPS System Replacement Battery Cartridges (R.B.C.). Visit Tripp Lite on the Web at
www.tripplite.com/products/battery-finder/ to locate the specific UPS replacement battery.
• Do not operate UPS without batteries.
CAUTION: The unit is intended for use with Lithium Iron Phosphate batteries
provided by Tripp Lite. DO NOT mix with Sealed Lead Acid batteries. External
battery packs are not supported with this model. DO NOT attempt to add external
batteries.
UPS and Battery Recycling
Please recycle Tripp Lite Products. The batteries used in Tripp Lite products are lithium
iron phosphate batteries. These batteries are highly recyclable. Please refer to local codes
for disposal requirements.
Call Tripp Lite for recycling info at 1.773.869.1234.
Visit Tripp Lite’s Website for up-to-date information on recycling the batteries or any
Tripp Lite product. Please follow this link:
http://www.tripplite.com/support/recycling-program/
Replacement Battery
MODEL BATTERY AND QUANTITY
NOMINAL VOLTAGE
OF BATTERY STRING PART NUMBER
SMART700HGL Lithium Iron Phosphate 12V / 3 pcs. 39.6V, 5Ah RBC51L / 3 pcs.
SMART1200XLHGL Lithium Iron Phosphate 12V / 3 pcs. 39.6V, 5Ah RBC51L / 3 pcs.
16-07-004-933608.indb 4 8/31/2016 9:59:31 AM
5
Important Safety Instructions continued
Package Contents
Maintenance:
• Other than battery replacement, the UPS does not require maintenance. There are no user
serviceable parts inside. Battery replacement should only be performed by qualified service
personnel.
Cleaning/Disinfecting:
• Before cleaning or disinfecting, the UPS should be turned off and unplugged.
• For cleaning the UPS, only a damp cloth should be used.
• For disinfecting the UPS, a damp cloth wetted with isopropyl alcohol may be used. No other
cleaning agent should be used.
UPS and Battery Disposal
• Always comply with local ordinances for proper methods of recycling and disposal of electronic
equipment.
• When purchasing a new UPS from Tripp Lite, you may send an old UPS back for recycling on a
one-for-one, like-for-like basis. The new equipment should also be sent back to Tripp Lite when it
ultimately becomes waste.
• Batteries can present risk of electric shock, burn and fire if not disposed of properly.
SMART700HGL
• USB A/B Cable, 6 ft.
• DB9 Cable, 6 ft.
• Owner’s Manual
SMART1200XLHGL
• USB A/B Cable, 6 ft.
• DB9 Cable, 6 ft.
• PowerAlert
®
Software Kit
• Owner’s Manual
16-07-004-933608.indb 5 8/31/2016 9:59:31 AM
6
1
Remove the two screws on
the battery door.
2
Remove the battery door.
Connecting the Batteries
1
2
3
4
5 6
7
The UPS is shipped with the battery disconnected. The battery must be connected for the UPS to
operate. Connect the batteries to the UPS prior to connecting the UPS to AC mains, or connecting
any equipment to the UPS.
The installation procedure is as follows:
3
Slightly slide the battery
pack out.
4
Remove insulation on the
negative (-) battery terminal.
5
Connect the negative (-)
battery terminal to the black
battery wire.
6
Apply the insulation tape to
negative (-) battery terminal.
7
Slide the battery pack back
into the UPS.
8
Re-install the battery door
removed in step 2.
9
Reinstall the two screws
removed in step 1.
16-07-004-933608.indb 6 8/31/2016 9:59:33 AM
7
Quick Installation
1
Plug the UPS into a 3-wire grounded,
120V AC, 60 Hz utility outlet.
Note: UL 60601-1 listed UPS systems only meet UL standard UL
60601-1 for medical equipment when plugged into a hospital-grade
outlet.
Note: UPS system will function properly upon initial startup; however,
maximum runtime for the unit’s battery will only be accessible after it
has been charged for 24 hours.
After plugging the UPS into a live AC outlet, the UPS will
automatically charge its batteries but will not supply power
to its outlets until it is turned ON (see Step 3 below). The
BATTERY CHARGE LED will be the only LED illuminated.
1
2
3
2
Plug equipment into the UPS.
The UPS will overload if the total VA ratings for all of connected
equipment exceeds the UPS Output Capacity. To find an equipment’s
VA rating, look on its nameplates. If the equipment is listed in amps,
multiply the number of amps by 120 to determine VA (Example:
1 amp x 120 = 120VA). If unsure the UPS outlets are overloaded,
see “OUTPUT LOAD LEVEL” LED description.
3
Turn the UPS ON.
Press and hold the “POWER” button for one second. The
alarm will beep once briefly after one second has passed.
Release the button.
The UPS batteries must be fully charged (minimum 24 hours) before plugging
equipment into the UPS.
16-07-004-933608.indb 7 8/31/2016 9:59:34 AM
8
Quick Installation Optional
1
2
These connections are optional. Your UPS will function properly without these connections.
1
Serial Communications
You can connect the UPS system’s DB9 port to the DB9 port
of a computer with the included cable. Use with
Tripp Lite’s PowerAlert Software for automatic file saves
and safe shutdown in case of power failure. (See Basic
Operation section.)
2
USB Communications
Connect the USB port of your UPS to the USB port of a
computer with the included cable. Use with Tripp Lite’s
PowerAlert Software for automatic file saves and safe
shutdown in case of power failure. (See Basic Operation
section.)
16-07-004-933608.indb 8 8/31/2016 9:59:34 AM
9
Basic Operation
Buttons
“POWER” Button:
• To turn the UPS ON: With the UPS plugged into a live AC wall outlet,* press
and hold the POWER button for about two seconds.** Release the button. If
utility power is absent, the UPS can receive a “cold-start” (i.e.: turn it ON and
supply power for a limited time from its batteries***) by pressing and holding
the POWER button for about two seconds.**
• To turn the UPS OFF: With the UPS ON and receiving utility power, press and
hold the POWER button for one second.** Then unplug the UPS from the wall
outlet. The UPS will be completely OFF.
*After plugging the UPS into a live AC outlet, the UPS will automatically charge its batteries,
but will not supply power to its outlets until it is turned ON. ** The alarm will beep once
briefly after the indicated interval has passed. *** If fully charged.
“MUTE/TEST” Button:
To Re-enable Audible Alarms: The UPS ships with the audible alarms muted by
default. To re-enable the audible alarms, press and hold the MUTE/TEST button
until a short beep sounds, followed by a continuous beep; then release the button.
To disable the audible alarms, press and hold the MUTE/TEST button until a short
beep followed by another short beep sounds; then release the button.
To Silence (or “Mute”) UPS Alarms: Briefly press and release the MUTE/TEST
button.*
To Run a Self-Test: With the UPS plugged in and turned ON, press and hold the
MUTE/TEST button for two seconds.* The alarm will beep several times and the
UPS will perform a self-test. See “Results of a Self-Test” below.
Note: Equipment can remain powered on during a self-test. However, the UPS will not
perform a self-test if it is not turned ON (see “POWER” Button description).
CAUTION! Do not unplug the UPS to test its batteries. This will remove
safe electrical grounding and may introduce a damaging surge into your
network connections.
Results of a Self-Test: The test will last approximately 10 seconds as the
UPS switches to battery to test its load capacity and battery charge.** If the
“OUTPUT LOAD LEVEL” LED remains lit red and the alarm continues to sound
after the test, the UPS outlets are overloaded. To clear the overload, unplug
some equipment and run the self-test repeatedly until the “OUTPUT LOAD
LEVEL” LED is no longer lit red and the alarm is no longer sounding.
CAUTION! Any overload not corrected by the user immediately following
a self-test may cause the UPS to shut down and cease supplying output
power in the event of a blackout or severe brownout.
If the “BATTERY WARNING” LED remains lit and the alarm continues to sound
after the test, the UPS batteries need to be recharged or replaced. Allow
the UPS to recharge continuously for 12 hours, and repeat the self-test. If
the LED remains lit, contact Tripp Lite for service. If the UPS requires battery
replacement, visit www.tripplite.com/products/battery-finder/ to locate the UPS
system’s appropriate Tripp Lite replacement battery.
*The alarm will beep once briefly after the indicated interval has passed. **Operation
during the self-test: the “POWER” LED will be flashing and the “OUTPUT LOAD LEVEL” and
“BATTERY CHARGE” LEDs will be lit and the UPS alarm will sound.
16-07-004-933608.indb 9 8/31/2016 9:59:46 AM
10
Basic Operation continued
Indicator Lights
All Indicator Light descriptions apply when the UPS is plugged into an AC outlet and turned on.
“POWER” LED
This green LED illuminates continuously when the UPS is ON and supplying
connected equipment with AC power from a utility source. The LED flashes
and an alarm sounds (4 short beeps followed by a pause) to indicate the UPS
is operating from its internal batteries during a blackout or severe brownout.
If the blackout or severe brownout is prolonged, save all files and shut down
equipment, as the internal battery power will eventually be depleted. See
“BATTERY CHARGE” LED description below.
“VOLTAGE CORRECTION” LED
This green LED illuminates continuously whenever the UPS is automatically
correcting high or low AC voltage on the utility line without the assistance of
battery power. The UPS will also emit a slight clicking noise. These are normal,
automatic operations of the UPS. No action is required.
“OUTPUT LOAD LEVEL” LED
This multicolored LED indicates the approximate electrical load of equipment
connected to the UPS AC outlets. It will turn from green (light load) to yellow
(medium load) to red (overload). If the LED is red (either illuminated continuously
or flashing), clear the overload immediately by unplugging some equipment from
the outlets until the LED changes from red to yellow (or green) and the alarm
is no longer sounding. CAUTION! Any overload not corrected by the user
immediately may cause the UPS to shut down and cease supplying output
power in the event of a blackout or severe brownout.
“BATTERY CHARGE / BATTERY POWER” LED
When the UPS is operating from utility power, this multicolored LED indicates the
approximate charge state of the UPS system’s internal batteries: red indicates
the batteries are beginning to charge; yellow indicates the batteries are roughly
midway through charging; and green indicates the batteries are fully charged.
When the UPS is operating from battery power during a blackout or severe
brownout, this LED indicates the approximate amount of energy (ultimately
affecting runtime) the UPS batteries will provide: red indicates a low level of
energy; yellow indicates a medium level of energy; and green indicates a high
level of energy. Since the runtime performance of all UPS batteries will gradually
deplete over time, it is recommended to periodically perform a self-test (see
“MUTE/TEST” Button description) to determine the energy level of your UPS
batteries BEFORE a blackout or severe brownout occurs. During a prolonged
blackout or severe brownout, save all files and shut down equipment, as battery
power will eventually be depleted. When the LED turns red and an alarm sounds
continuously, it indicates the UPS batteries are nearly out of power and shut down
is imminent.
“BATTERY WARNING” LED
This LED illuminates red and an alarm sounds intermittently after initiating a
self-test (see “MUTE/TEST” Button description) to indicate the UPS batteries
need to be recharged or replaced. Allow the UPS to recharge continuously for
12 hours, and repeat the self-test. If the LED continues to light, contact
Tripp Lite for service. If the UPS requires battery replacement, visit
www.tripplite.com/products/battery-finder/ to locate the UPS system’s
appropriate Tripp Lite replacement battery.
16-07-004-933608.indb 10 8/31/2016 9:59:46 AM
11
Basic Operation continued
Other UPS Features
Hospital-Grade AC Receptacles: The receptacles provide connected equipment
with AC line power during normal operation and battery power during blackouts
and brownouts. They also protect equipment against damaging surges and line
noise.
USB or DB9 Communication Port: These ports connect the UPS to a computer
for automatic file saves and unattended shutdown in the event of a power failure.
Use with Tripp Lite’s PowerAlert Software and appropriate USB or DB9 cable. A
PowerAlert CD and USB or DB9 cable may be included with the UPS; if so, insert
the CD into the computer’s CD-ROM drive and follow the installation instructions.
If PowerAlert Software and the appropriate cable were not included with the UPS,
a free software download is available at www.tripplite.com. Any user-supplied DB9
pass-through or USB cable may then be used to connect the UPS to a computer.
NOTE: This connection is optional. The UPS will work properly without this connection.
Battery Replacement Door: Under normal conditions, the original UPS battery
will last several years. Battery replacement should be performed by qualified
service personnel only. Refer to “Battery Warnings” in the Safety section. Should
the UPS require battery replacement, visit Tripp Lite on the Web at
www.tripplite.com/products/battery-finder/ to locate the UPS system’s
appropriate Tripp Lite replacement battery.
Input Breaker: Protects the electrical circuit from overcurrent draw from the
UPS load. If breaker trips, remove some of the load, then reset it by pressing the
breaker in.
Equipotential Connection: Use this to connect any equipment that requires a
protective earth ground.
Power Sensitivity Adjustment: This dial is normally set fully counterclockwise,
which enables the UPS to protect against waveform distortions in its AC input.
When such distortion occurs, the UPS will normally switch to providing PWM
sine wave power from its battery reserves for as long as the distortion is present.
In areas with poor utility power or where the UPS system’s input power comes
from a backup generator, chronic waveform distortion could cause the UPS to
switch to battery too frequently, draining its battery reserves. The frequency in
which the UPS switches to battery due to waveform distortion can be adjusted by
experimenting with different the dial settings. As the dial is turned clockwise, the
UPS becomes more tolerant of variations in its input power’s AC waveform.
NOTE: The further the dial is adjusted clockwise, the greater the degree of waveform
distortion the UPS will allow to pass to connected equipment. When experimenting with
different settings for this dial, operate connected equipment in a safe test mode so that
the effect on the equipment of any waveform distortions in the UPS system’s output can be
evaluated without disrupting critical operations.
NORM DELAY
16-07-004-933608.indb 11 8/31/2016 9:59:47 AM
12
Guidance and Manufacturer’s Declaration
Guidance and Manufacturer’s Declaration—Electromagnetic Emissions
This Medical-Grade UPS is intended for use in the electromagnetic environment specified below. The customer
or the user of this Medical-Grade UPS should ensure that it is used in such an environment.
Emissions Test Compliance Electromagnetic Environment - Guidance
RF Emissions CISPR 11 Group 1 The Medical-Grade UPS uses RF energy only for
its internal function. Therefore, its RF emissions
are very low and unlikely to cause any interference
in nearby electronic equipment.
RF Emissions CISPR 11 SMART700HGL: Class A
SMART1200XLHGL: Class A
The Medical-Grade UPS is suitable for use in all
establishments other than domestic and those
directly connected to the public low-voltage power
supply network that supplies buildings used for
domestic purposes.
Guidance and Manufacturer’s Declaration—Electromagnetic Immunity
This Medical-Grade UPS is intended for use in the electromagnetic environment specified below. The customer
or the user of this Medical-Grade UPS should ensure that it is used in such an environment.
Immunity Test IEC 60601 Test Level
Compliance
Level
Electromagnetic
Environment - Guidance
Electrostatic Discharge (ESD)
IEC 61000-4-2
+ / - 6kV contact
+ / - 8kV air
Complies Floors should be wood,
concrete or ceramic tile. If
floors are covered with synthetic
material, the relative humidity
should be at least 30%.
Electrical Fast Transient/Burst
IEC 61000-4-3
+ / - 2kV for power supply lines
+ / - 1kV for input/output lines
Complies Mains power quality should be
that of a typical commercial or
hospital environment.
Surge
IEC 61000-4-5
+ / - 1kV differential mode
+ / - 2kV common mode
Complies Mains power quality should be
that of a typical commercial or
hospital environment.
Voltage dips, short
interruptions and voltage
variations on power supply
input lines
IEC 61000-4-11
<5% U
T
(>95% dip in U
T
) for .5 cycle
40% U
T
(60% dip in U
T
) for 5 cycles
70% U
T
(30% dip in U
T
) for 25 cycles
<5% U
T
(>95% dip in U
T
) for 5 seconds
Complies Mains power quality should be
that of a typical commercial or
hospital environment.
Power Frequency (50/60 Hz)
Magnetic Field
IEC 61000-4-B
3 A/m Complies Power frequency magnetic
fields should be at levels
characteristic of a typical
location in a typical commercial
or hospital environment.
Note: U
T
is the AC mains voltage prior to application of the test level.
16-07-004-933608.indb 12 8/31/2016 9:59:47 AM
13
Storage and Service
Storage
Before storing your UPS, turn it completely OFF: with the UPS ON and receiving utility power, press
and hold the POWER button for one second (an alarm will beep once briefly after the interval has
passed); then, unplug the UPS from the wall outlet. CAUTION! Your UPS has an internal power
source. Its outlets may still deliver current, even after the UPS is unplugged, until the UPS
is completely turned OFF (deactivated). If you store your UPS for an extended period of time,
recharge the UPS batteries once every three months: plug the UPS into a wall outlet; allow it to
charge for 12 hours; and then unplug it and place it back in storage. Note: after you plug the UPS
in, it will automatically begin charging its batteries; however, it will not supply power to its outlets
(see Quick Installation section). If you leave your UPS batteries discharged for an extended period of
time, they will suffer a permanent loss of capacity.
Permissible Storage and Transportation Conditions
Humidity 0-95% Non-Condensing
Temperature 5°F to 122°F (-15°C to 50°C)
Elevation 0 to 50,000 ft. (0 to 15,240 m)
Atmospheric Pressure >11.1 kPa
Service
For more information on service, visit www.tripplite.com/support. Before returning your product for
service, follow these steps:
1. Review the installation and operation procedures in this manual to ensure that the service
problem does not originate from a misreading of the instructions. Also, check that the UPS
system’s circuit breaker(s) are not tripped. This is the most common cause of service inquiries
which can be easily remedied by following the resetting instructions in this manual.
2. If the problem continues, do not contact or return the product to the dealer. Instead, visit
www.tripplite.com/support.
3. If the problem requires service, visit www.tripplite.com/support and click the Product Returns link.
From here you can request a Returned Material Authorization (RMA) number, which is required
for service. This simple on-line form will ask for your unit’s model and serial numbers, along with
other general purchaser information. The RMA number, along with shipping instructions will be
emailed to you. Any damages (direct, indirect, special or consequential) to the product incurred
during shipment to Tripp Lite or an authorized Tripp Lite service center are not covered under
warranty. Products shipped to Tripp Lite or an authorized Tripp Lite service center must have
transportation charges prepaid. Mark the RMA number on the outside of the package. If the
product is within its warranty period, enclose a copy of your sales receipt. Return the product for
service using an insured carrier to the address given to you when you request the RMA.
16-07-004-933608.indb 13 8/31/2016 9:59:47 AM
14
Regulatory Compliance and Product Registration
UL CLASSIFICATION FOR MEDICAL EQUIPMENT: Class I, Type B, Ordinary Equipment, Continuous Operation.
UL1778 APPROVAL: All the UPS systems described in this manual are UL1778 listed. All meet strict
requirements for UPS protection. They provide battery backup during blackouts, switching between utility power
and battery backup power in 2-4 milliseconds. In addition, all have hospital-grade plugs and receptacles that
reduce the possibility of accidental equipment disconnection. All are suitable for use in hospitals, outside patient
care areas.
UL60601-1 APPROVAL: Several of the UPS models described in this manual are UL 60601-1 listed (see
specifications). They incorporate Faraday-shielded isolation transformers that reduce the cumulative leakage
current of all connected equipment to below 100 microamps. These models are suitable for use in hospitals,
including inside patient care areas.
REGULATORY COMPLIANCE IDENTIFICATION NUMBERS:
For the purpose of regulatory compliance certifications and identification, your Tripp Lite product has been
assigned a unique series number. The series number can be found on the product nameplate label, along with
all required approval markings and information. When requesting compliance information for this product, always
refer to the series number. The series number should not be confused with the marketing name or model number
of the product.
FCC RADIO/TV INTERFERENCE NOTICE (FOR CLASS A MODELS):
Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
when operated in a commercial environment. This equipment generates, uses and can radiate radio frequency
energy, and if not installed and used in accordance with the instruction manual, may cause interference to radio
communications. Operation of this equipment is likely to cause harmful interference in which case the user will
be required to correct the interference at his own expense. The user must use shielded cables and connectors
with this product. Any changes or modifications to this product not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
PRODUCT REGISTRATION
Visit www.tripplite.com/warranty today to register your new Tripp Lite product. You’ll be automatically
entered into a drawing for a chance to win a FREE Tripp Lite product!*
* No purchase necessary. Void where prohibited. Some restrictions apply. See website for details.
Tripp Lite has a policy of continuous improvement. Product specifications are subject to change without notice.
1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support
Note on Labeling
Two symbols are used on the label.
V~ : AC Voltage
V : DC Voltage
16-07-004-933608.indb 14 8/31/2016 9:59:47 AM
15
Manual de operación
Importantes instrucciones de seguridad 16
Contenido del Empaque 19
Conexión de las Baterías 20
Instalación rápida 21
Operación básica 22
Orientación y Declaración del Fabricante 27
Almacenamiento y servicio 28
Cumplimiento de las Normas 29
English 1
Français 30
1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support
© 2016 Tripp Lite. Reservados todos los derechos.
MÁS DE
SmartPro
®
Sistemas UPS de Grado Médico
(con Baterías de Litio de Fosfato de Hierro)
Modelos:
SMART700HGL
(Número de Serie: AG-8863)
SMART1200XLHGL
(Número de Serie: AG-8862)
16-07-004-933608.indb 15 8/31/2016 9:59:48 AM
16
Importantes instrucciones de seguridad
CONSERVE ESTAS INSTRUCCIONES
Este manual contiene instrucciones y advertencias que deben seguirse durante la instalación,
operación y almacenamiento de todos los Sistemas UPS de Tripp Lite. La falta de observar estas
advertencias podría afectar su garantía.
Declaración de Uso Indicado
Los Sistemas UPS de Grado Médico de Tripp Lite están diseñados para soportar y proteger equipo
de computación no médico y médico y dispositivos médicos que requieran reducción de fuga de
corriente, protección contra sobretensiones, regulación de voltaje, filtrado de ruido en la línea y
respaldo por batería durante interrupción en el servicio eléctrico y prueba del generador, ambos
dentro y fuera de áreas de atención a pacientes. Los Sistemas UPS de Grado Médico de Tripp Lite
vienen con clavijas y tomacorrientes de grado hospital que reducen la fuga a menos de 100µA.
Información del Producto
SMART700HGL SMART1200XLHGL
Voltaje de Entrada de CA 120 120
Rango de Voltaje de Entrada de CA 81–143 81–143
Amperes de Entrada 5.5 9.2
Amperes de Salida 5.8 6.25
Potencia Especificada (VA/Watts) 700VA/450W 1000VA/750W
Frecuencia 60 Hz 60 Hz
No. de Fases Mono Mono
Tipo de Clase Clase I Clase I
Tipo de Clavija/Conector NEMA 5-15P NEMA 5-15P
Operación Continua Continua
Protección de Entrada de CA
(Cant./Tipo/Especif.)
Breaker de entrada
(2 x 10A), térmico
Breaker de entrada
(2 x 15A), térmico
Corriente Máx de Fuga (µA) Menos de 100 µA Menos de 100 µA
Peso 15.3 kg (33.7 lb.) 15.2 kg (33.6 lb.)
Contraindicación Conocida Ninguna Ninguna
Advertencias de Ubicación del UPS
Símbolos Importantes
Significa que debe revisarse la información en el manual antes de usarlo.
Se usa para indicar una advertencia de que un párrafo es particularmente importante y puede
representar un riesgo a la seguridad.
Advertencia-Voltaje Peligroso No sentarse
Denota un signo de advertencia general No pararse sobre la superficie
Consulte el Manual / Folleto de Instrucciones No Empujar
16-07-004-933608.indb 16 8/31/2016 9:59:48 AM
17
Importantes instrucciones de seguridad continuación
• No use este equipo en atmósferas enriquecidas con oxígeno o a distancias inferiores a 0.3 m (1
pie) de un punto en que se ventile deliberadamente una atmósfera enriquecida con oxígeno.
• Tenga cuidado al levantar el UPS. Debido al peso considerable de todos los sistemas UPS, deben
ayudar al menos dos personas para levantarlos e instalarlos.
• Instale su UPS en interiores, alejado de humedad o calor excesivos, polvo o luz solar directa.
• Para mejor desempeño, el UPS debe usarse en una ubicación que cumpla con las siguientes
condiciones: Temperatura: 0 a 40° C (32 a 104° F); Humedad: 0 a 95% (sin condensación);
Elevación: <2,000 m (6,562 pies) sobre el nivel del mar.
• Deje espacio adecuado alrededor del UPS para una ventilación apropiada. No obstruya las
ventilaciones o aberturas de ventiladores.
• No instale la unidad con su panel frontal o posterior viendo hacia abajo (en cualquier ángulo).
El instalar de esta manera inhibirá seriamente el enfriamiento interno de la unidad, causando
eventualmente daño al producto no cubierto por la garantía.
• El UPS no está previsto para contacto con el paciente. Evite la instalación que pudiera causar
contacto accidental con los pacientes.
Advertencias para la Conexión del UPS
• El UPS contiene su propia fuente de energía (batería). Las terminales de salida pueden estar
energizadas, aún cuando el UPS no esté conectado a una alimentación de CA.
• Conecte su UPS a un tomacorriente de CA conectado correctamente a tierra. No modifique
la clavija del UPS en modo alguno que pueda eliminar la conexión a tierra del UPS. No use
adaptadores que eliminen la conexión a tierra del UPS.
• No enchufe su UPS en sí mismo; esto dañará al UPS y anulará su garantía.
• Si está conectando su UPS a un generador de CA activado por motor, el generador de
proporcionar una salida filtrada y con frecuencia regulada.
• Para retirar el UPS de la alimentación del servicio público, la clavija sirve como dispositivo de
desconexión.
• Una vez conectado, no limite el acceso a la clavija de entrada. La clavija debe estar accesible
para usarla como medio de desconexión.
• Al conectar su UPS al tomacorriente de alimentación, asegúrese que el tomacorriente de
alimentación cuente con protección adecuada contra sobrecorriente de acuerdo con sus códigos
eléctricos nacionales y locales. Garantice que la protección contra sobrecorriente tenga una
capacidad de interrupción mínima de 1500A.
PRECAUCIÓN: No retire la cubierta durante 5 minutos después de desconectar
todas las fuentes de alimentación. Riesgo de electrocución—partes energizadas
peligrosas en el interior. No retire la cubierta. No hay en el interior partes a las que
el usuario pueda dar servicio. Remita el servicio a personal de servicio calificado.
Este UPS recibe energía de más fuentes de CD; se requiere la desconexión de la
fuente de CA y CD para desenergizar la unidad antes de darle serviicio.
PRECAUCIÓN: Para garantizar la correcta conexión a tierra con la alimentación
de energía de la red pública, el cable de entrada debe conectarse con una clavija
específica autorizada para el país con una conexión de protección a tierra.
PRECAUCIÓN: Si este producto está operado en respaldo por batería (no está
conectado a la energía de la red pública), deben emplearse las salvaguardas
adecuadas para protegerse contra un contacto accidental con conductores de
energía de CA.
PRECAUCIÓN: No exceda la salida total especificada.
ADVERTENCIA: No se permite ninguna modificación de este equipo.
16-07-004-933608.indb 17 8/31/2016 9:59:48 AM
18
Importantes instrucciones de seguridad continuación
Advertencias para la Conexión del Equipo
• No use los Sistemas UPS de Tripp Lite para aplicaciones de soporte de vida en los que un mal
funcionamiento o falla de un de Sistema UPS de Tripp Lite pudiera causar una falla o alterar
significativamente el desempeño de un dispositivo de soporte de vida.
• La salida de CA es flotante (El conductor neutro de la salida no está conectado a tierra).
• No conecte supresores de sobretensiones o cables de extensión a la salida de su UPS. Esto
puede dañar el UPS y afectar las garantías del supresor de sobretensiones y del UPS.
PRECAUCIÓN: La unidad es para interconexión exclusiva con equipo certificado por
IEC 60601-1 en el entorno del paciente y equipo certificado por IEC 60950-1 fuera
del entorno del paciente. No haga contacto con SIP/SOP (como el puerto USB,
puerto RS-232, etc.) y el paciente al mismo tiempo.
Advertencias de la Batería
• Debido a que las baterías presentan un peligro de choque eléctrico y quemaduras por las altas
corrientes de cortocircuito, tome las precauciones adecuadas. No deseche las baterías en un
incinerador. No abra las baterías. No ponga los terminales de la batería en corto o en puente
con ningún objeto. Apague y desconecte el UPS antes de reemplazar la batería. Sólo debe
cambiar las baterías personal técnico debidamente capacitado. Use herramientas con mangos
aislados y reemplace las baterías existentes con el mismo número y tipo de baterías nuevas
(Litio de Fosfato de Hierro). Las baterías del UPS son reciclables. Al final de la vida de la
unidad de UPS, siga las buenas prácticas descargando la batería antes de desecharla.
Consulte la reglamentación local para los requisitos de disposición de desechos o visita
www.tripplite.com/UPSbatteryrecycling para reciclar información. Tripp Lite ofrece una línea
completa de Cartuchos de reemplazo de batería para UPS (R.B.C.). Visite Tripp Lite en la web en
www.tripplite.com/products/battery-finder/ para localizar la batería de reemplazo específica para
su UPS.
• No opere el UPS sin baterías.
PRECAUCIÓN: La unidad está diseñada para uso con baterías de Litio-Ferrofosfato
suministradas por Tripp Lite. NO mezcle con baterías selladas de plomo ácido.
Este modelo no permite módulos de baterías externas. No intente agregar baterías
externas.
Reciclaje de UPS y Baterías
Por favor recicle los productos de Tripp Lite. Las baterías usadas en los productos de
Tripp Lite son batería Litio de Fosfato de Hierro. Estas baterías son altamente reciclables.
Refiérase por favor a sus códigos locales para requerimientos de desecho.
Puede llamar a Tripp Lite para reciclar, información al 1.773.869.1234.
Puede acudir al sitio Web de Tripp Lite en busca de información actualizada sobre el
reciclaje de baterías o cualquier producto de Tripp Lite. Siga por favor este enlace:
http://www.tripplite.com/support/recycling-program/
Batería de Reemplazo
MODELO BATERÍA Y CANTIDAD
VOLTAJE NOMINAL DEL
JUEGO DE BATERÍAS
NO. DEL MÓDULO
DE BATERÍAS
SMART700HGL
Litio de Fosfato de Hierro 12V / 3 piezas.
39.6V, 5Ah RBC51L / 3 pzas.
SMART1200XLHGL Litio de Fosfato de Hierro 12V / 3 pzas. 39.6V, 5Ah RBC51L / 3 piezas.
16-07-004-933608.indb 18 8/31/2016 9:59:48 AM
19
Importantes instrucciones de seguridad continuación
Contenido del Empaque
Mantenimiento:
• Fuera del remplazo de baterías, el UPS no requiere mantenimiento. No tiene partes a las que el
usuario pueda dar servicio. El reemplazo de la batería debe llevarse a cabo sólo por personal de
servicio calificado.
Limpieza/Desinfección:
• Antes de la limpieza o desinfección, el UPS debe apagarse y desconectarse.
• Para limpiar el UPS debe usarse solo un trapo húmedo.
• Para desinfectar el UPS puede usarse un trapo humedecido con alcohol isopropílico. No debe
usarse otro agente limpiador.
Desecho del UPS y Batería
• Cumpla siempre con los reglamentos locales para los métodos adecuados de reciclado y
desecho de equipo electrónico.
• Al comprar un UPS nuevo de Tripp Lite, usted puede enviar un UPS viejo para ser reciclado en
una base de uno por uno y similar por similar. El equipo nuevo debe enviarse también a Tripp Lite
cuando se convierta en desperdicio.
• Las baterías pueden presentar el riesgo de descarga eléctrica, quemaduras e incendio si no se
desechan correctamente.
SMART700HGL
• Cable USB A/B, 1.83 m [6 pies]
• Cable DB9, 1.83 m [6 pies]
• Manual del Propietario
SMART1200XLHGL
• Cable USB A/B, 1.83 m [6 pies]
• Cable DB9, 1.83 m [6 pies]
• Juego de Programa PowerAlert®
• Manual del Propietario
16-07-004-933608.indb 19 8/31/2016 9:59:48 AM
20
1
Retire los dos tornillos en la
puerta de la batería.
2
Retire la puerta de la batería.
Conexión de las Baterías
1
2
3
4
5 6
7
El UPS se embarca con la batería desconectada. Para operar el UPS, debe conectarse la batería.
Conecte las baterías al UPS antes de conectar el UPS a la alimentación de CA o conectar cualquier
equipo al UPS.
El procedimiento de instalación es como sigue:
3
Deslice ligeramente hacia
afuera el módulo de baterías.
4
Quite el aislamiento en la
terminal negativa (-) de la
batería y el cable negro.
5
Conecte la terminal negativa
(-) de la batería al cable
negro de la batería.
6
Aplique la cinta de aislar a
la terminal negativa (-) de la
batería.
7
Deslice el módulo de baterías
de regreso en el UPS.
8
Reinstale la puerta de la
batería retirada en el paso 2.
9
Reinstale los dos tornillos
retirados en el paso 1.
16-07-004-933608.indb 20 8/31/2016 9:59:51 AM
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
Tripp Lite SMART700HGL & SMART1200XLHGL Le manuel du propriétaire
- Catégorie
- Alimentations sans interruption (UPS)
- Taper
- Le manuel du propriétaire
dans d''autres langues
Documents connexes
-
Tripp Lite SMART700HGL & SMART1200XLHGL Le manuel du propriétaire
-
Tripp Lite Flatpack UPS Systems Guide de démarrage rapide
-
Tripp Lite SmartPro® and OmniSmart® Medical-Grade UPS Systems Le manuel du propriétaire
-
-
-
-
-
-
-
Tripp Lite SMX & OMNIX UPS Systems Le manuel du propriétaire