Tripp Lite SMX1200XLHGL Le manuel du propriétaire

1

Owner’s Manual

SMX

Medical-Grade UPS Systems

with Lithium Iron Phosphate Batteries

Models:

Important Safety Instructions 2

Package Contents 5

Connecting the Batteries 6

Quick Installation 7

Basic Operation 8

Guidance and Manufacturer’s Declaration 11

Storage & Service 12

Battery Warranty Information 13

Regulatory Compliance 13

Español 14

Français 27

Русский 40

Deutsch 53

SMX700HGL

(Series Number: AG-031B)

SMX1200XLHGL

(Series Number: AG-031C)

1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support

18-06-259-933821.indb 1 6/20/2018 3:08:23 PM

2

Important Safety Instructions

Statement of Intended Use

Tripp Lite Medical-Grade UPS Systems are intended to support and protect non-medical computer

equipment and medical devices that require leakage current reduction, surge protection, voltage

regulation, line noise ﬁltering and battery backup during power outages and generator testing, both

inside and outside patient care areas. Tripp Lite’s Medical-Grade UPS Systems come with hospital-

grade plugs and receptacles that reduce leakage to below 100μA.

Product Information

SMX700HGL SMX1200XLHGL

AC Input Voltage 230V 230V

Input Amp(s) 3.6 5

Output Amp(s) 2 3.3

Rated Power (VA/Watts) 700VA, 450W 1000VA, 750W

Frequency 50/60 Hz 50/60 Hz

No. of Phases Single Single

Class Type Class I Class I

Plug/Connector Type Inlet C14 with dongle Inlet C14 with dongle

Operation Continuous Continuous

AC Input Protection (Qty/type/rating) Input breaker (2 x 5A) thermal Input breaker (2 x 6A) thermal

Max Leakage Current (uA) Less than 100uA Less than 100uA

Weight 14.3 kg 15.9 kg

Known Contraindication None None

SAVE THESE INSTRUCTIONS

This manual contains important instructions that should be followed during the installation,

operation and storage of all Tripp Lite UPS Systems. Failure to heed these warnings may affect

your warranty.

Note: Your UPS incorporates overcurrent protection in both the L1 and L2 input conductors.

UPS Location Warnings

Relevant Symbols

Denotes that information in the manual should be reviewed before use.

Used to signal as a warning that a statement is particularly important and could pose a safety

risk.

Warning-Dangerous Voltage No sitting

Denotes general warning sign No stepping on surface

Refer to Instruction Manual/Booklet No pushing

18-06-259-933821.indb 2 6/20/2018 3:08:23 PM

3

Important Safety Instructions

• Do not use this equipment within oxygen-enriched atmospheres, or within 0.3 m of a point at

which an oxygen-enriched atmosphere is intentionally vented.

• Use caution when lifting UPS. Because of the considerable weight of all UPS systems, at least

two people should assist in lifting and installing them.

• Install your UPS indoors, away from excess moisture or heat, dust or direct sunlight.

• For best performance, the UPS should be used in a location that meets the following conditions:

Temperature: 0 to 40° C; Humidity: 0 to 95% (non-condensing);

Elevation: <2,000 m above sea level; Pressure: >95kPa

• Leave adequate space around all sides of the UPS for proper ventilation. Do not obstruct its vents

or fan openings.

• Do not mount unit with its front or rear panel facing down (at any angle). Mounting in this manner

will seriously inhibit the unit’s internal cooling, eventually causing product damage not covered

under warranty.

• The UPS is not intended for patient contact. Avoid installations that will cause accidental patient

contact.

UPS Connection Warnings

• The UPS contains its own energy source (battery). The output terminals may be live even when

the UPS is not connected to an AC supply.

• Connect your UPS to a properly grounded AC power outlet. Do not modify the UPS’s plug in a

way that would eliminate the UPS’s connection to ground. Do not use adapters that eliminate the

UPS’s connection to ground.

• Do not plug your UPS into itself; this will damage the UPS and void your warranty.

• If you are connecting your UPS to a motor-powered AC generator, the generator must provide

ﬁltered, frequency-regulated output.

• To remove the UPS from the supply mains, the appliance inlet serves as a disconnect device.

• Once connected, do not limit access to the input plug. The plug must be accessible to be used as

a means of disconnection.

• When connecting the UPS to a power outlet, ensure the power outlet is provided with suitable

overcurrent protection in accordance with national and local electrical codes. Ensure the

overcurrent protection has a minimum of 1500A breaking capacity.

CAUTION: Do not remove cover for 5 minutes after disconnecting all sources of

supply. Risk of electric shock—hazardous live parts inside. User must not remove

cover. No user serviceable parts inside. Refer servicing to qualiﬁed service

personnel. This UPS receives power from more DC sources; disconnection of the

AC and DC source is required to de-energize the unit before servicing.

CAUTION: To ensure proper grounding with supply mains power, the input cord must

be connected with an approved country-speciﬁc plug with a protective earth ground

connection.

CAUTION: If this product is operated on battery (not connected to mains power),

adequate safeguards should be employed to protect against accidental contact

with AC power conductors.

CAUTION: Do not exceed total rated output.

WARNING: No modiﬁcation of this equipment is allowed.

18-06-259-933821.indb 3 6/20/2018 3:08:23 PM

4

Important Safety Instructions

Equipment Connection Warnings

• Do not use Tripp Lite UPS Systems for life-support applications in which a malfunction or failure

of a Tripp Lite UPS System could cause failure or signiﬁcantly alter the performance of a life-

support device.

• The AC output is ﬂoating (the neutral output conductor is not grounded).

• Do not connect surge suppressors or extension cords to the output of your UPS. This might

overload the UPS and will void the surge suppressor and UPS warranties.

CAUTION: The unit is for exclusive interconnection with IEC 60601-1 certiﬁed

equipment in the patient environment and IEC 60950-1 certiﬁed equipment outside

of the patient environment. Do not contact SIP/SOP (such as the USB port, RS232

port, etc.) and the patient at the same time.

Battery Warnings

• Batteries can present a risk of electrical shock and burn from high short-circuit current. Observe

proper precautions. Do not dispose of the batteries in a ﬁre. Do not open the UPS or batteries.

Do not short or bridge the battery terminals with any object. Unplug and turn off the UPS before

performing battery replacement. Use tools with insulated handles. There are no user-serviceable

parts inside the UPS. Only authorized service personnel using the same number and type

of batteries (lithium iron phosphate) should perform battery replacement. The batteries are

recyclable. At the end of the UPS unit’s life, follow best practice by discharging the battery prior to

disposal. Refer to local codes for disposal requirements. Tripp Lite offers a complete line of UPS

System Replacement Battery Cartridges (R.B.C.). Visit Tripp Lite on the Web at

www.tripplite.com/products/battery-ﬁnder/ to locate the speciﬁc UPS replacement

battery.

• Do not operate UPS without batteries.

CAUTION: The unit is intended for use with lithium iron phosphate batteries

provided by Tripp Lite. DO NOT mix with sealed lead acid batteries. This model does

not support external battery packs. DO NOT attempt to add external batteries.

UPS and Battery Recycling

Please recycle Tripp Lite Products. The batteries used in Tripp Lite products are lithium iron

phosphate batteries. These batteries are highly recyclable. Please refer to local codes for

disposal requirements.

Call Tripp Lite for recycling info at 1.773.869.1234.

For up-to-date information on recycling the batteries in this UPS or any Tripp Lite product,

visit Tripp Lite’s website: http://www.tripplite.com/support/recycling-program/

Replacement Batteries

MODEL

BATTERY

AND QUANTITY

NOMINAL VOLTAGE

OF BATTERY STRING PART NUMBER

SMX700HGL Lithium Iron Phosphate

12V / 3 pcs.

39.6V, 5Ah RBC51L / 3 pcs.

SMX1200XLHGL Lithium Iron Phosphate

12V / 3 pcs.

39.6V, 5Ah RBC51L / 3 pcs.

18-06-259-933821.indb 4 6/20/2018 3:08:23 PM

5

Important Safety Instructions

Package Contents

Maintenance:

• Other than battery replacement, the UPS does not require maintenance. There are no user-

serviceable parts inside. Battery replacement should only be performed by qualiﬁed service

personnel.

Cleaning/Disinfecting:

• Before cleaning or disinfecting, the UPS should be turned off and unplugged.

• For cleaning the UPS, only a damp cloth should be used.

• For disinfecting the UPS, a damp cloth wetted with isopropyl alcohol may be used. No other

cleaning agent should be used.

UPS and Battery Disposal

• Always comply with local ordinances for proper methods of recycling and disposal of electronic

equipment.

• Batteries can present risk of electric shock, burn and ﬁre if not disposed of properly.

SMX700HGL

• 1.8 m USB Cable

• 1.8 m DB9 Cable

• Owner’s Manual

SMX1200XLHGL

• 1.8 m USB Cable

• 1.8 m DB9 Cable

• Owner’s Manual

18-06-259-933821.indb 5 6/20/2018 3:08:23 PM

6

Connecting the Batteries

1

Remove the two screws on

the battery door.

2

Remove the battery door.

1

2

3

4

5 6

7

The UPS is shipped with the battery disconnected. The battery must be connected for the UPS to

operate. Connect the batteries to the UPS prior to connecting the UPS to AC mains or connecting

any equipment to the UPS.

The installation procedure is as follows:

3

Slightly slide the battery

pack out.

4

Remove insulation on the

negative (-) battery terminal.

5

Connect the negative (-)

battery terminal to the black

battery wire.

6

Apply the insulation tape to

negative (-) battery terminal.

7

Slide the battery pack back

into the UPS.

8

Reinstall the battery door

removed in step 2.

9

Reinstall the two screws

removed in step 1.

18-06-259-933821.indb 6 6/20/2018 3:08:26 PM

7

Quick Installation

1

Plug your UPS into a 3-wire grounded,

230V AC 50/60 Hz utility outlet.

After you plug the UPS into a live AC outlet, the UPS will

automatically charge its batteries, but will not supply power

to its outlets until it is turned ON (see Step 3 below). The

BATTERY CHARGE LED will be the only LED illuminated.

2

Plug your equipment into the UPS.*

* You will overload the UPS if the total VA ratings for all the

equipment you connect exceeds the UPS’s Output Capacity (see

Speciﬁcations). To ﬁnd your equipment’s VA ratings, look on their

nameplates. If the equipment is listed in amps, multiply the number

of amps by 230 to determine VA. (Example: 1 amp × 230 V = 230

VA). If you are unsure you have overloaded the UPS’s outlets, see

“OUTPUT LOAD LEVEL” LED description.

Note: UPS system will function properly upon initial startup; however,

maximum runtime for the unit’s battery will only be accessible after it

has been charged for 24 hours.

3

Turn the UPS ON.

Press and hold the “POWER” button for one second. The

alarm will beep once brieﬂy after one second has passed.

Release the button.

NORM DELAY

1

2

3

NORM DELAY

1

2

The following connections are optional; your UPS will function properly without these

connections:

1

Serial Communications

(select models only)

You can connect the DB9 serial port on the UPS to the DB9

port of a computer with the included cable. Use with

Tripp Lite’s PowerAlert

®

software for automatic ﬁle saves

and safe shutdown in case of power failure. (See Basic

Operation Section.)

2

USB Communications

Connect the USB port of your UPS to the USB port of a

computer with the included cable. Use with Tripp Lite’s

PowerAlert software for automatic ﬁle saves and safe

shutdown in case of power failure. (See Basic Operation

Section.)

The UPS battery must charge for 24 hours before use.

18-06-259-933821.indb 7 6/20/2018 3:08:28 PM

8

Basic Operation

Buttons

“POWER” Button:

• To turn the UPS ON: With the UPS plugged into a live AC wall outlet,* press

and hold the POWER button for one second.** Release the button. If utility

power is absent, you can “cold-start” the UPS (i.e., turn it ON and supply

power for a limited time from its batteries***) by pressing and holding the

POWER button for about two seconds.**

• To turn the UPS OFF: With the UPS ON and receiving utility power, press and

hold the POWER button for one second.** Then unplug the UPS from the wall

outlet. The UPS will be completely OFF.

* After you plug the UPS into a live AC outlet, the UPS will automatically charge its batteries,

but will not supply power to its outlets until it is turned ON. ** The alarm will beep once

brieﬂy after the indicated interval has passed. *** Fully charged batteries are recommended.

“MUTE/TEST” Button:

To Silence (or “Mute”) UPS Alarms: Brieﬂy press and release the MUTE/TEST

button.*

To Run a Self-Test: With your UPS plugged in and turned ON, press and hold

the MUTE/TEST button for two seconds.* The alarm will beep once. Release the

button, and the UPS will perform a self-test. See “Results of a Self-Test” below.

Note: you can leave connected equipment on during a self-test. Your UPS, however, will not

perform a self-test if it is not turned ON (see “POWER” Button description).

CAUTION! Do not unplug your UPS to test its batteries. This will

remove safe electrical grounding and may introduce a damaging

surge into your network connections.

Results of a Self-Test: The test will last approximately 10 seconds as the UPS

switches to battery to test its load capacity and battery charge.** If the “OUTPUT

LOAD LEVEL” LED remains lit red and the alarm continues to sound after the test,

the UPS’s outlets are overloaded. To clear the overload, unplug some of your

equipment and run the self-test repeatedly until the “OUTPUT LOAD LEVEL” LED is

no longer lit red and the alarm is no longer sounding.

CAUTION! Any overload that is not corrected by the user

immediately following a self-test may cause the UPS to shut down

and cease supplying output power in the event of a blackout or

severe brownout.

If the “BATTERY WARNING” LED remains lit and the alarm continues to sound

after the test, the UPS batteries need to be recharged or replaced. Allow the

UPS to recharge continuously for 12 hours, and repeat the self-test. If the

LED remains lit, contact Tripp Lite for service. If your UPS requires battery

replacement, visit www.tripplite.com/products/battery-ﬁnder to locate the speciﬁc

Tripp Lite replacement battery for your UPS.

* The alarm will beep once brieﬂy after the indicated interval has passed. ** The “POWER”

LED will be ﬂashing and the “OUTPUT LOAD LEVEL” and “BATTERY CHARGE” LEDs will be lit

and the UPS alarm will sound.

18-06-259-933821.indb 8 6/20/2018 3:08:28 PM

9

Basic Operation

Indicator Lights

All Indicator Light descriptions apply when the UPS is plugged into an AC outlet and turned on.

“POWER” LED: This green LED lights continuously when the UPS is ON and

supplying connected equipment with AC power from a utility source. The LED

ﬂashes and an alarm sounds (4 short beeps followed by a pause) to indicate the

UPS is operating from its internal batteries during a blackout or severe brownout.

If the blackout or severe brownout is prolonged, you should save ﬁles and shut

down your equipment since internal battery power will eventually be depleted.

See “BATTERY CHARGE” LED description below.

“VOLTAGE CORRECTION” LED: This green LED lights continuously whenever the

UPS is automatically correcting high or low AC voltage on the utility line without

the assistance of battery power. The UPS will also emit a slight clicking noise.

These are normal, automatic operations of the UPS. No action is required on your

part.

“OUTPUT LOAD LEVEL” LED: This multicolored LED indicates the approximate

electrical load of equipment connected to the UPS’s AC outlets. It will turn from

green (light load) to yellow (medium load) to red (overload). If the LED is red

(either illuminated continuously or ﬂashing), clear the overload immediately by

unplugging some of your equipment from the outlets until the LED changes from

red to yellow (or green) and the alarm is no longer sounding.

CAUTION! Any overload that is not corrected by the user

immediately may cause the UPS to shut down and cease

supplying output power in the event of a blackout or severe

brownout.

“BATTERY CHARGE / BATTERY POWER” LED: When the UPS is operating from

utility power, this multicolored LED indicates the approximate charge state of

the UPS’s internal batteries: red indicates the batteries are beginning to charge,

yellow indicates the batteries are roughly midway through charging and green

indicates the batteries are fully charged. When the UPS is operating from battery

power during a blackout or severe brownout, this LED indicates the approximate

amount of energy (ultimately affecting runtime) that the UPS’s batteries will

provide: red indicates a low level of energy, yellow indicates a medium level of

energy and green indicates a high level of energy.

Because runtime performance of all UPS batteries will gradually deplete over

time, it is recommended you periodically perform a self-test (see “MUTE/TEST”

Button description) to determine the energy level of your UPS batteries BEFORE

a blackout or severe brownout occurs. During a prolonged blackout or severe

brownout, you should save ﬁles and shut down your equipment because battery

power will eventually be depleted. When the LED turns red and an alarm sounds

continuously, it indicates the UPS’s batteries are nearly out of power and UPS

shutdown is imminent.

“BATTERY WARNING” LED: This LED lights red and an alarm sounds

intermittently after you initiate a self-test (See “MUTE/TEST” Button description)

to indicate the UPS batteries need to be recharged or replaced. Allow the UPS to

recharge continuously for 12 hours, and repeat the self-test. If the LED continues

to light, contact Tripp Lite for service. If your UPS requires battery replacement,

visit www.tripplite.com/products/battery-ﬁnder to locate the speciﬁc Tripp Lite

replacement battery for your UPS.

18-06-259-933821.indb 9 6/20/2018 3:08:28 PM

10

Basic Operation

Other UPS Features

AC Receptacles: The receptacles provide your connected equipment with AC

line power during normal operation and battery power during blackouts and

brownouts. They also protect your equipment against damaging surges and line

noise.

USB or DB9 Communication Port: These ports can connect your UPS to any

computer for automatic ﬁle saves and unattended shutdown in the event of a

power failure. Use with Tripp Lite’s PowerAlert Software and appropriate USB or

DB9 cable. You can obtain the software FREE via the Web at www.tripplite.com.

Any user-supplied DB9 pass-through or USB cable may be used to connect your

UPS to your computer.

Note: This connection is optional. The UPS will work properly without this connection.

Battery Replacement Door: Under normal conditions, the original battery in

your UPS will last several years. Battery replacement should be performed only

by qualiﬁed service personnel. Refer to “Battery Warnings” in the Safety section.

Should your UPS require battery replacement, visit www.tripplite.com/products/

battery-ﬁnder to locate the speciﬁc replacement battery for your UPS.

Input Breakers: Protects your electrical circuit from overcurrent draw from the

UPS load. If breaker trips, remove some of the load, then reset it by pressing the

breaker in.

Equipotential Connection: Use this to connect any equipment that requires a

chassis ground.

Power Sensitivity Adjustment: This dial is normally set fully counterclockwise,

which enables the UPS to protect against waveform distortions in its AC input.

When such distortion occurs, the UPS will normally switch to providing PWM

sine wave power from its battery reserves for as long as the distortion is present.

In areas with poor utility power or where the UPS’s input power comes from a

backup generator, chronic waveform distortion could cause the UPS to switch

to battery too frequently, draining its battery reserves. You may be able to

reduce how often your UPS switches to battery due to waveform distortion by

experimenting with different settings for this dial. As the dial is turned clockwise,

the UPS becomes more tolerant of variations in its input power’s AC waveform.

Note: The further the dial is adjusted clockwise, the greater the degree of waveform

distortion the UPS will allow to pass to connected equipment. When experimenting with

different settings for this dial, operate connected equipment in a safe test mode so that the

effect on the equipment of any waveform distortions in the UPS’s output can be evaluated

without disrupting critical operations.

NORM DELAY

18-06-259-933821.indb 10 6/20/2018 3:08:29 PM

11

Guidance and Manufacturer’s Declaration

Guidance and Manufacturer’s Declaration—Electromagnetic Emissions

This Medical-Grade UPS is intended for use in the electromagnetic environment speciﬁed below. The customer

or the user of this Medical-Grade UPS should assure that it is used in such an environment.

Emissions Test Compliance Electromagnetic Environment - Guidance

RF Emissions CISPR 11 Group 1 The Medical-Grade UPS uses RF energy only for its internal

function. Therefore, its RF emissions are very low and unlikely to

cause any interference in nearby electronic equipment.

RF Emissions CISPR 11 Class B The Medical-Grade UPS is suitable for use in all establishments

other than domestic and those directly connected to the public

low-voltage power supply network that supplies buildings used for

domestic purposes.

Guidance and Manufacturer’s Declaration—Electromagnetic Immunity

This Medical-Grade UPS is intended for use in the electromagnetic environment speciﬁed below. The customer

or the user of this Medical-Grade UPS should assure that it is used in such an environment.

Immunity Test IEC 60601 Test Level

Compliance

Level

Electromagnetic

Environment - Guidance

Electrostatic Discharge (ESD)

IEC 61000-4-2

+ / - 6kV contact

+ / - 8kV air

Complies Floors should be wood,

concrete or ceramic tile.

If colors are covered with

synthetic material, the relative

humidity should be at least

30%.

Electrical Fast Transient/Burst

IEC 61000-4-3

+ / - 2kV for power supply lines

+ / - 1kV for input/output lines

Complies Mains power quality should be

that of a typical commercial or

hospital environment.

Surge

IEC 61000-4-5

+ / - 1kV differential mode

+ / - 2kV common mode

Complies Mains power quality should be

that of a typical commercial or

hospital environment.

Voltage dips, short

interruptions and voltage

variations on power supply

input lines

IEC 61000-4-11

<5% U

T

(>95% dip in U

T

) for .5 cycle

40% U

T

(60% dip in U

T

) for 5 cycles

70% U

T

(30% dip in U

T

) for 25 cycles

<5% U

T

(>95% dip in U

T

) for 5 seconds

Complies Mains power quality should be

that of a typical commercial or

hospital environment.

Power Frequency (50/60 Hz)

Magnetic Field

IEC 61000-4-B

3 A/m Complies Power frequency magnetic

ﬁelds should be at levels

characteristic of a typical

location in a typical commercial

or hospital environment.

Note: U

T

is the AC mains voltage prior to application of the test level.

18-06-259-933821.indb 11 6/20/2018 3:08:29 PM

12

Storage & Service

Storage

Before storing your UPS, turn it completely OFF. With the UPS ON and receiving utility power, press

and hold the POWER button for one second (an alarm will beep once brieﬂy after the interval has

passed). Then, unplug the UPS from the wall outlet.

CAUTION! Your UPS has an internal power source. Its outlets may still deliver

current, even after the UPS is unplugged, until the UPS is completely turned OFF

(deactivated).

If you store your UPS for an extended period of time, recharge the UPS batteries once every three

months: plug the UPS into a wall outlet; allow it to charge for 12 hours, and then unplug it and

place it back in storage.

Note: after you plug the UPS in, it will automatically begin charging its batteries; however, it will not supply power

to its outlets (see Quick Installation section). If you leave your UPS batteries discharged for an extended period of

time, they will suffer a permanent loss of capacity.

Permissible Storage and Transportation Conditions

Humidity 0-95% Non-Condensing

Temperature -15°C to 45°C

Elevation 0 to 15,240 m

Atmospheric Pressure >95 kPa

Service

A variety of Extended Warranty and On-Site Service Programs are available from Tripp Lite. For more

information on service, visit www.tripplite.com/support. Before returning your product for service,

follow these steps:

1. Review the installation and operation procedures in this manual to insure that the service

problem does not originate from a misreading of the instructions.

2. If the problem continues, do not contact or return the product to the dealer. Instead, visit

www.tripplite.com/support.

3. If the problem requires service, visit www.tripplite.com/support and click the Product Returns link.

From here you can request a Returned Material Authorization (RMA) number, which is required

for service. This simple on-line form will ask for your unit’s model and serial numbers, along with

other general purchaser information. The RMA number, along with shipping instructions will be

emailed to you. Any damages (direct, indirect, special or consequential) to the product incurred

during shipment to Tripp Lite or an authorized Tripp Lite service center are not covered under

warranty. Products shipped to Tripp Lite or an authorized Tripp Lite service center must have

transportation charges prepaid. Mark the RMA number on the outside of the package. If the

product is within its warranty period, enclose a copy of your sales receipt. Return the product for

service using an insured carrier to the address given to you when you request the RMA.

18-06-259-933821.indb 12 6/20/2018 3:08:29 PM

13

Battery Warranty Information

Regulatory Compliance

Regulatory Compliance Identiﬁcation Numbers

For the purpose of regulatory compliance certiﬁcations and identiﬁcation, your Tripp Lite product has been

assigned a unique series number. The series number can be found on the product nameplate label, along with

all required approval markings and information. When requesting compliance information for this product, always

refer to the series number. The series number should not be confused with the marking name or model number of

the product.

WEEE Compliance Information for Tripp Lite Customers and Recyclers

(European Union)

Under the Waste Electrical and Electronic Equipment (WEEE) Directive and implementing regulations,

when customers buy new electrical and electronic equipment from Tripp Lite they are entitled to:

• Send old equipment for recycling on a one-for-one, like-for-like basis

(this varies depending on the country)

• Send the new equipment back for recycling when this ultimately becomes waste

UPS and Battery Recycling

Please recycle Tripp Lite Products. The batteries used in Tripp Lite products are lithium iron phosphate

batteries. These batteries are highly recyclable. Please refer to your local codes for disposal

requirements.

Tripp Lite has a policy of continuous improvement. Product speciﬁcations are subject to change without notice.

1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support

Tripp Lite’s warranty for lithium iron phosphate batteries, including those in the SMX700HGL and

SMX1200XLHGL, is 5 years. These batteries support frequent charge/discharge cycles, such as

mobile cart applications where the UPS is often disconnected from an AC power source or when

the AC power source has frequent outages. Unlike traditional sealed lead acid batteries, lithium

iron phosphate batteries have the ability to cycle multiple times per day and provide up to 10,000

cycles, 20-30 times the cycle life of traditional batteries.

This warranty does not apply to traditional sealed lead acid batteries. Visit www.tripplite.com for

more information and speciﬁcs on battery type, battery life and warranty for the UPS you intend to

use for your application.

18-06-259-933821.indb 13 6/20/2018 3:08:29 PM

14

Manual del Propietario

SMX

Sistemas UPS de Grado Médico

con Baterías de Litio-Ferrofosfato

Modelos:

Instrucciones de Seguridad Importantes 15

Contenido del Empaque 18

Conexión de las Baterías 19

Instalación Rápida 20

Operación Básica 21

Orientación y Declaración del Fabricante 24

Almacenamiento y Servicio 25

Información de la Garantía de la Batería 26

Cumplimiento de las Regulaciones 26

English 1

Français 27

Русский 40

Deutsch 53

SMX700HGL

(Número de Serie: AG-031B)

SMX1200XLHGL

(Número de Serie: AG-031C)

1111 W. 35th Street, Chicago, IL 60609 EE. UU. • www.tripplite.com/support

18-06-259-933821.indb 14 6/20/2018 3:08:29 PM

15

Instrucciones de Seguridad Importantes

Declaración de Uso Previsto

Los Sistemas UPS de Grado Médico de Tripp Lite están diseñados para soportar y proteger equipo

de computación no médico y dispositivos médicos que requieran reducción de fuga de corriente,

protección contra sobretensiones, regulación de voltaje, ﬁltrado de ruido en la línea y respaldo por

batería durante interrupciones en el servicio eléctrico y prueba del generador, ambos dentro y fuera

de áreas de atención al cuidado de pacientes. Los Sistemas UPS de Grado Médico de Tripp Lite

vienen con clavijas y tomacorrientes de grado hospital que reducen la fuga a menos de 100 µA.

Información del Producto

SMX700HGL SMX1200XLHGL

Voltaje de Entrada de CA 230V 230V

Amperes de Entrada 3.6 5

Amperes de Salida 2 3.3

Potencia Especiﬁcada (VA / Watts) 700VA, 450W 1000VA, 750W

Frecuencia 50Hz / 60Hz 50Hz / 60Hz

Nº de Fases Mono Mono

Tipo de Clase Clase I Clase I

Tipo de Clavija/Conector Entrada C14 con llave electrónica Entrada C14 con llave electrónica

Operación Continua Continua

Protección de Entrada de CA (Canti-

dad / Tipo / Especiﬁcación)

Breaker térmico de entrada (2

x 5A)

breaker térmico de entrada (2

x 6A)

Corriente Máx de Fuga (µA) Menos de 100 µA Menos de 100 µA

Peso 14.3 kg 15.9 kg

Contraindicación Conocida Ninguna Ninguna

CONSERVE ESTAS INSTRUCCIONES

Este manual contiene instrucciones importantes que deben seguirse durante la instalación,

operación y almacenamiento de todos los Sistemas UPS de Tripp Lite. La omisión en la

observancia de estas advertencias puede afectar la garantía.

Nota: Su UPS incorpora protección contra sobrecorriente en los conductores de entrada L1 y L2.

Advertencias para la Ubicación del UPS

Símbolos Importantes

Signiﬁca que debe revisarse la información en el manual antes de usarlo.

Se usa para indicar como advertencia que un párrafo es particularmente importante y puede

representar un riesgo a la seguridad.

Advertencia-Voltaje Peligroso No sentarse

Denota un signo de advertencia general No pararse sobre la superﬁcie

Consulte el Manual / Folleto de Instruc-

ciones

No Empujar

18-06-259-933821.indb 15 6/20/2018 3:08:30 PM

16

Instrucciones de Seguridad Importantes

• No use este equipo en atmósferas enriquecidas con oxígeno o a distancias inferiores a 30.5 cm [1 pie]

de un punto en que se ventile deliberadamente una atmósfera enriquecida con oxígeno.

• Tenga cuidado al levantar el UPS. Debido al considerable peso de todos los sistemas UPS, al menos

dos personas deben ayudar para levantarlos e instalarlos.

• Instale su UPS en interiores, alejado de humedad o calor excesivos, polvo o luz solar directa.

• Para mejor desempeño, el UPS debe usarse en una ubicación que cumpla con las siguientes

condiciones: Temperatura: 0 ºC a 40 °C [32 ºF a 104 ºF]; Humedad: 0% a 95% (sin condensación);

Elevación: <2,000 m sobre el nivel del mar; Presión: >95 kPa

• Deje un espacio adecuado alrededor de todos los lados del UPS para una ventilación apropiada. No

obstruya las ventilaciones o aberturas de los ventiladores.

• No instale la unidad con su panel frontal o posterior viendo hacia abajo (en cualquier ángulo). Al

instalarlo de esta manera inhibirá seriamente el enfriamiento interno de la unidad, causando un daño al

producto que no está cubierto por la garantía.

• El UPS no está previsto para contacto con el paciente. Evite instalaciones que pudieran causar contacto

accidental con el paciente.

Advertencias para la Conexión del UPS

• El UPS contiene su propia fuente de energía (batería). Las terminales de salida pueden estar

energizadas, aún cuando el UPS no esté conectado a una alimentación de CA.

• Conecte su UPS a un tomacorrientes de CA conectado correctamente a tierra. No modiﬁque la clavija

del UPS en modo alguno que pueda eliminar la conexión a tierra del UPS. No use adaptadores que

eliminen la conexión a tierra del UPS.

• No enchufe su UPS en sí mismo; esto dañará al UPS y anulará su garantía.

• Si está conectando su UPS a un generador de CA activado por motor, el generador de proporcionar una

salida ﬁltrada y con frecuencia regulada.

• Para retirar el UPS de la alimentación de la red del servicio público, la clavija del dispositivo sirve como

dispositivo de desconexión.

• Una vez conectado, no limite el acceso a la clavija de entrada. La clavija debe ser accesible para usarla

como medio de desconexión.

• Al conectar el UPS a un tomacorrientes de alimentación, asegúrese que el tomacorrientes de

alimentación cuente con protección adecuada contra sobrecorriente de acuerdo con los códigos

eléctricos nacionales y locales. Asegúrese de que la protección contra sobrecorriente tenga una

capacidad de interrupción mínima de 1500A.

PRECAUCIÓN: No retire la cubierta durante 5 minutos después de desconectar todas

las fuentes de alimentación. Riesgo de electrocución—partes energizadas peligrosas en

el interior. El usuario no debe retirar la cubierta. No hay en el interior partes a las que

el usuario pueda dar servicio. Remita el servicio a personal de servicio caliﬁcado. Este

UPS recibe energía de más fuentes de CD; se requiere la desconexión de la fuente de

CA y CD para desenergizar la unidad antes de darle servicio.

PRECAUCIÓN: Para garantizar la correcta conexión a tierra con la alimentación

de energía de la red pública, el cable de entrada debe conectarse con una clavija

especíﬁca autorizada para el país con una conexión de protección a tierra.

PRECAUCIÓN: Si este producto está operado en respaldo por batería (no está conectado

a la energía de la red pública), deben emplearse las protecciones adecuadas para

protegerse contra un contacto accidental con conductores de energía de CA.

PRECAUCIÓN: No exceda la salida total especiﬁcada.

ADVERTENCIA: No se permite ninguna modiﬁcación de este equipo.

18-06-259-933821.indb 16 6/20/2018 3:08:30 PM

17

Instrucciones de Seguridad Importantes

Advertencias para la Conexión del Equipo

• No use los Sistemas UPS de Tripp Lite para aplicaciones de soporte de vida en los que un mal

funcionamiento o falla de un de Sistema UPS de Tripp Lite pudiera causar una falla o alterar

signiﬁcativamente el desempeño de un dispositivo de soporte de vida.

• La salida de CA es ﬂotante (El conductor neutro de la salida no está conectado a tierra).

• No conecte supresores de sobretensiones o cables de extensión a la salida de su UPS. Esto

puede sobrecargar al UPS y anulará las garantías del supresor de sobretensiones y del UPS.

PRECAUCIÓN: La unidad es para interconexión exclusiva con equipo certiﬁcado por

IEC 60601-1 en el entorno del paciente y equipo certiﬁcado por IEC 60950-1 fuera

del entorno del paciente. No haga contacto con SIP / SOP (como el puerto USB,

puerto RS232, etc.) y el paciente al mismo tiempo.

Advertencias de la Batería

• Las baterías pueden presentar un riesgo de descarga eléctrica y quemaduras por la alta corriente

de corto circuito. Observe las precauciones apropiadas. No deseche las baterías en el fuego.

No abra el UPS o las baterías. No ponga en corto o puentee las terminales de la batería con

objeto alguno. Desenchufe y apague el UPS antes de reemplazar la batería. Use herramientas

con mangos aislados. No hay partes dentro del UPS a las que el usuario pueda dar servicio. El

reemplazo de la batería debe realizarlo solo el personal de servicio autorizado usando el mismo

número y tipo de baterías (Litio-Ferrofosfato). Las baterías son reciclables. Al ﬁnal de la vida

de la unidad del UPS, siga las siguientes buenas prácticas para descargar la batería antes de

desecharla. Para los requisitos de desecho, consulte los reglamentos y códigos locales. Tripp

Lite ofrece una línea completa de Cartuchos de Batería de Repuesto (R.B.C.) para Sistema UPS.

Para localizar la batería de repuesto especíﬁca para el UPS, visite Tripp Lite en el sitio

www.tripplite.com.

• No opere el UPS sin baterías.

PRECAUCIÓN: La unidad está diseñada para uso con baterías de Litio-Ferrofosfato

suministradas por Tripp Lite. NO mezcle con baterías selladas de plomo ácido.

Este modelo no soporta módulos de baterías externas. No intente agregar baterías

externas.

Reciclado de la Batería y el UPS

Recicle por Favor los Productos de Tripp Lite. Las baterías usadas en productos de Tripp

Lite son baterías de Litio-Ferrofosfato. Estas baterías son altamente reciclables. Para los

requisitos de desecho, por favor consulte sus códigos locales.

Llame a Tripp Lite al 1.773.869.1234 para obtener información de reciclado.

Para obtener información actualizada sobre el reciclaje de las baterías o cualquier

producto de Tripp Lite, vaya al sitio Web de Tripp Lite: http://www.tripplite.com/support/

recycling-program/

Baterías de Reemplazo

MODELO

BATERÍA

Y CANTIDAD

VOLTAJE NOMINAL

DE LA CADENA DE

BATERÍAS NÚMERO DE PARTE

SMX700HGL Litio-Ferrofosfato de

12V / 3 piezas.

39.6V, 5Ah RBC51L / 3 piezas.

SMX1200XLHGL Litio-Ferrofosfato de

12V / 3 piezas.

39.6V, 5Ah RBC51L / 3 piezas.

18-06-259-933821.indb 17 6/20/2018 3:08:30 PM

18

Instrucciones de Seguridad Importantes

Contenido del Empaque

Mantenimiento:

• Fuera del remplazo de baterías, el UPS no requiere mantenimiento. No tiene partes a las que el

usuario pueda dar servicio. El reemplazo de la batería debe llevarse a cabo sólo por personal de

servicio caliﬁcado.

Limpieza / Desinfección:

• Antes de la limpieza o desinfección, el UPS debe apagarse y desconectarse.

• Para limpiar el UPS debe usarse solo un trapo húmedo.

• Para desinfectar el UPS puede usarse un trapo humedecido con alcohol isopropílico. No debe

usarse otro agente limpiador.

Desecho del UPS y la Batería

• Cumpla siempre con los reglamentos locales para los métodos adecuados de reciclado y

desecho de equipo electrónico.

• Las baterías pueden presentar el riesgo de descarga eléctrica, quemaduras e incendio si no se

desechan correctamente.

SMX700HGL

• Cable USB de 1.8 m

• Cable DB9 de 1.8 m

• Manual del Propietario

SMX1200XLHGL

• Cable USB de 1.8 m

• Cable DB9 de 1.8 m

• Manual del Propietario

18-06-259-933821.indb 18 6/20/2018 3:08:30 PM

19

Conexión de las Baterías

1

Retire los dos tornillos en la

puerta de la batería.

2

Retire la puerta de la batería.

1

2

3

4

5 6

7

El UPS se embarca con la batería desconectada. Para operar el UPS, debe conectarse la batería.

Conecte las baterías al UPS antes de conectar el UPS a la alimentación de CA o conectar cualquier

equipo al UPS.

El procedimiento de instalación es como sigue:

3

Deslice un poco hacia afuera el

módulo de baterías.

4

Quite el aislamiento en la

terminal negativa (-) de la batería.

5

Conecte la terminal negativa (-)

de la batería al cable negro de la

batería.

6

Aplique la cinta de aislar a la

terminal negativa (-) de la batería.

7

Deslice el módulo de baterías

nuevamente dentro del UPS.

8

Reinstale la puerta de la batería

retirada en el paso 2.

9

Reinstale los dos tornillos

retirados en el paso 1.

18-06-259-933821.indb 19 6/20/2018 3:08:33 PM

20

Instalación Rápida

1

Enchufe su UPS en un tomacorrientes de

la red del servicio público de 3 hilos con

conexión a tierra, 120V CA, 60 Hz.

Después de conectar el UPS en un tomacorrientes de CA

activo, el UPS cargará automáticamente sus baterías, pero

no suministrará energía a sus tomacorrientes hasta que

se encienda (ver paso 3 a continuación). El LED “BATTERY

CHARGE” [Carga de Batería] será el único LED iluminado.

2

Enchufe su equipo en el UPS.

* Usted sobrecargará el UPS si el valor total en VA para todo el

equipo que conecte excede la capacidad de salida del UPS (Vea

Especiﬁcaciones). Para localizar los valores de VA de su equipo,

consulte las placas de identiﬁcación. Si el equipo está especiﬁcado

en amperes, multiplique el número de amperes por 230 para

determinar VA (Ejemplo: 1 amp x 230 = 230VA). Si no está seguro

de haber sobrecargado las salidas del UPS, consulte la descripción

de LED "NIVEL DE CARGA DE SALIDA".

Nota: El sistema UPS funcionará correctamente en el arranque inicial;

no obstante, la autonomía máxima para la batería de la unidad sólo

será accesible después de haberse cargado por 24 horas.

3

Encienda el UPS.

Presione y sostenga por el botón “POWER” por un segundo.

La alarma emitirá un breve bip después de transcurrido un

segundo. Suelte el botón.

NORM DELAY

1

2

3

NORM DELAY

1

2

La siguientes conexiones son opcionales; su UPS trabajará correctamente sin estas

conexiones:

1

Comunicaciones Seriales

(sólo modelos selectos)

Puede conectar el puerto DB9 serial en el UPS al puerto

DB9 de la computadora con el cable incluido. Úselo con el

Software PowerAlert

®

de Tripp Lite para el apagado seguro

del sistema y guardado de los archivos automáticamente

en caso de una falla de energía. (Vea la sección Operación

Básica).

2

Comunicaciones USB

Conecte el puerto USB del UPS al puerto USB de una

computadora con el cable incluido. Úselo con el Software

PowerAlert de Tripp Lite para el apagado seguro del sistema

y guardado de los archivos automáticamente en caso de

una falla de energía. (Vea la sección Operación Básica).

La batería del UPS debe cargarse por 24 horas antes de usarlo.

18-06-259-933821.indb 20 6/20/2018 3:08:35 PM

La page charge ...

Tripp Lite SMX1200XLHGL Le manuel du propriétaire

Ce manuel convient également à

Tripp Lite SMX1200XLHGL Le manuel du propriétaire

dans d''autres langues

Documents connexes