Fire Magic Aurora Stand-Alone Post Grill Manuel utilisateur

1

IMPORTANT:

READ THESE INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION OR USE.

DANGER:

IF YOU SMELL GAS:

1. Shut off the gas to the appliance.

2. Extinguish any open ﬂame.

3. Open lid.

4. If odor continues, keep away from the

appliance and immediately call your

gas supplier or the ﬁre department.

WARNING:

1. Do not store or use gasoline or other

ﬂammable vapors and liquids in the

vicinity of this or any other appliance.

2. An LP cylinder not connected for use

shall not be stored in the vicinity of this

or any other appliance.

CODE AND SUPPLY REQUIREMENTS: This grill

must be installed in accordance with local codes

and ordinances, or, in the absence of local codes,

with either the latest National Fuel Gas Code

(ANSI Z223.1/NFPA 54), and Natural Gas and

Propane Storage and Handling Installation Code

(CSA-B149.1).

This appliance and its dedicated manual shutoff

valve must be disconnected from the gas-supply

piping system when testing the system at pressures

in excess of ½ psig (3.5 kPa).

This appliance must be isolated from the gas-supply

piping system by closing its dedicated manual

shutoff valve during any pressure testing of the gas-

supply system at pressures up to and including ½

psig (3.5 kPa).

All electrical outlets in the vicinity of the grill must be

properly grounded in accordance with local codes,

or, in the absence of local codes, with the National

Electrical Code, ANSI/NFPA 70, or the Canadian

Electrical Code, CSA C22.1, whichever is applicable.

Keep all electrical-supply cords and fuel-supply

hoses away from any heated surface.

Robert H. Peterson Co. • 14724 East Proctor Avenue • City of Industry, CA 91746

INSTALLER: Leave these instructions with consumer.

CONSUMER: Retain for future reference.

WARNING:

Improper installation, adjustment,

alteration, service, or maintenance can

cause injury or property damage. For

proper installation, refer to the installation

instructions. For assistance or additional

information, consult a qualiﬁed professional

service technician, service agency, or the

gas supplier.

SAFETY AND WARNING CODES

STAND-ALONE POST OUTDOOR

GAS GRILLS

INSTALLATION AND

OWNER’S MANUAL

Proper operation of your grill requires

prompt and periodic maintenance.

See the SERVICING AND CLEANING

section for details.

REV 0 - B - 2006190710

L-C2-609

A430s (IN-GROUND AND PATIO MOUNT)

A430s Patio

mount model

shown

Certiﬁed to: ANSI Z21.58

CSA 1.6

US

®

C

ONLY TO BE USED OUTDOORS

Cooking Grid U.S.

Patent Nos.

D857,453

D862,984

2

IMPORTANT: LISEZ CES INSTRUCTIONS SOIGNEUSEMENT AVANT DE COMMENCER L’INSTALLATION OU L’UTILISATION

GRIL EXTÉRIEUR DE GAZ

DANGER:

SI VOUS SENTEZ LE GAZ :

1. Coupez le gaz à l’appareil.

2. Éteignez-vous n’importe quelle ﬂamme nue.

3. Ouvrez le couvercle si équipé d’un four.

4. Si l’odeur continue, gardez loin de

l’appareil et appelez immédiatement

votre département de fournisseur ou de

feu de gaz.

AVERTISSEMENT:

1. Ne stockez pas ou n’employez pas

l’essence ou d’autres vapeurs et liquides

inﬂammables à proximité de ceci ou

d’aucun autre appareil.

2. Un cylindre de propane non relié pour

l’usage ne sera pas stocké à proximité

de ceci ou d’aucun autre appareil.

CONDITIONS DE CODE ET D’APPROVISIONNEMENT:

Ce gril doit être installé selon des codes et des ordonnances

locaux, ou, en l’absence des codes locaux, avec l’un ou l’autre

le plus défunt Code national de gaz de carburant (norme ANSI

Z223.1/NFPA 54), et Stockage de gaz naturel et de propane

et manipulation du code d’installation (CSA-B149.1).

Cet appareil et ses différents robinets d’isolement doivent être

démontés du gaz-fournissent le système sifﬂant en examinant

le système aux pressions au-dessus du ½ psig (kPa 3.5).

Cet appareil doit être isolé dans gaz-fournissent le système

sifﬂant par fermeture que ses différents robinets d’isolement

manuels pendant tous les essais sous pression du gaz-

fournissent le système aux pressions jusques et y compris

le ½ psig (kPa 3.5).

Toutes les sorties électriques à proximité du gril doivent être

correctement fondues selon des codes locaux, ou en l’absence

de local code, avec le code électrique national, ANSI/NFPA

70, ou le code électrique canadien, CSA C22.1, celui qui est

applicable.

Maintenez tout électrique-fournissent des cordes et carburant-

fournissent des tuyaux partis de n’importe quelle surface de

chauffage.

INSTALLATEUR : Laissez ces instructions avec le consommateur.

CONSOMMATEUR : Maintenez pour la future référence.

AVERTISSEMENT:

L’installation inexacte, l’ajustement, le

changement, le service, ou l’entretien

peuvent causer des dommages ou des

dégats matériels. Référez-vous à ce manuel.

Pour de l'aide ou des renseignements

supplémentaires, consulter un technicien

professionnel qualifié de service, une

agence de service ou le fournisseur de gaz.

SÛRETÉ ET CODES D’AVERTISSEMENT

• Ce gril est pour ultilisation à l’extérieur seulement.

Si l’appareil est entreposé à l’intérieur, enlever les

bouteilles et les laisser à l’extérieur.

• Ne pas ranger le gril immédiatement aprés l’avoir utilisé.

le laisser refroidir avant de le déplacer ou de la ranger.

Le non respect de cette mesure de sécurité pourrait

entraîner un incendie causant des dommages à la

propriété, des blessures ou la mort.

• Ne pas utiliser cet appareil sous une surface combustible.

• Ne pas utiliser cet appareil sous un auvent. Le non

respect de cette mesure de sécurité pourrait entraîner

un incendie ou des blessures.

• Dégagement minimal entre les parois latérales et l’arriére

de l’appareil et la construction combustible (45.7 cm à

partir des parois latérales et 45.7cm à partir de l’arriére).

• Le régulareur de pression de gaz prévu avec cet appareil

de cuisson à gaz pour l’extérieur doit être utilisé. Ce

régulateur est réglé pour une pression de sortie de 5

pouces de colonne de l’eau pour le gaz naturel, et 10

pouces pour le propane.

• LE RÉGULATEUR INCLUS D’APPAREILS EST ÉVALUÉ

POUR LE MAXIMUM DE 1/2 (LIVRES PAR POUCE

CARRÉ). SI VOTRE OFFRE DE GAZ EST 1/2 PLUS

GRAND QUE (LIVRES PAR POUCE CARRÉ), UN

RÉGULATEUR ADDITIONNEL DOIT ÊTRE INSTALLÉ

AVANT LE GRIL. VOIR LA SECTION DE CONDITIONS

D’OFFRE DE GAZ POUR LA PRESSION APPROPRIÉE

D’OFFRE DE GAZ.

• Ne couvrez jamais la surface entière de cuisine ou de

gril de gauffreuses ou de casseroles. La surchauffe se

produira et les brûleurs ne seront pas très performants

quand la chaleur de combustion est emprisonnée au-

dessous de la surface à cuire.

• Ne pulvérisez jamais l’eau sur une unité chaude de gaz,

comme ceci peut endommager des composants de

porcelaine ou de fer de fonte.

• Une fuite de GPL peut causer une incendie ou une

explosion si enflammée entraînant des blessures

corporelles graves ou la mort.

• Communiquez avec le fournisseur de GPL pour les

réparations ou pour disposer de qules bouteille ou du

GPL non utilisé.

INSTALLATION INSTRUCTIONS ET MANUEL DU PROPRIÉTAIRE

Certiﬁé à la norme: ANSI Z21.58 / CSA 1.6

À UTILISER UNIQUEMENT À L'EXTÉRIEUR

Grille de cuisson Numéros de brevets américains:

D857,453 D862,984

REV 0 - B - 2006190710

L-C2-609

3

CONTENTS

GETTING STARTED

REV 0 - B - 2006190710

L-C2-609

GETTING STARTED

INSTALLATION, OPERATION, AND SAFETY INFORMATION �� 4

ELECTRICAL CONNECTIONS �� 4

GAS SAFETY INFORMATION �� 5

WARNING �� 5

WHEN USING PROPANE GAS �� 5

WHEN USING NATURAL GAS �� 5

INSTALLATION SAFETY GUIDELINES�� 5

OPERATING THE UNIT SAFELY AND CORRECTLY �� 5

SAFE USE & MAINTENANCE OF PROPANE GAS CYLINDERS �� 7

INSTALLATION REQUIREMENTS �� 8

OVERHEAD CONSTRUCTION AND EXHAUST HOOD REQUIREMENTS �� 8

REAR WALL CLEARANCES �� 9

SIDE WALL / CORNER WALL CLEARANCES (if applicable) �� 9

COMBUSTION AIR AND COOLING AIRFLOW �� 10

GAS-SUPPLY PLUMBING REQUIREMENTS �� 10

ELECTRICAL SAFETY �� 11

MODEL SPECIFICATIONS �� 12

POST GRILL WIRING DIAGRAM �� 12

AURORA GRILL REPLACEMENT PARTS LIST �� 15

INSTALLATION

PATIO MOUNT INSTALLATION �� 17

IN-GROUND POST INSTALLATION �� 19

INSTALL THE FLAVOR GRIDS �� 22

INSTALL THE COOKING GRIDS �� 22

INSTALL THE DRIP TRAY �� 22

INSTALL THE RIGID SHELVES �� 23

USE, CARE, & SERVICE

IDENTIFICATION OF GRILL CONTROLS �� 24

USING THE GRILL �� 25

LIGHTING (IGNITION) INSTRUCTIONS �� 27

ELECTRONIC LIGHTING �� 27

MANUAL LIGHTING �� 27

SETTING THE TIMER �� 27

SHUTTING OFF THE UNIT �� 27

OPTIONAL ROTISSERIE INSTRUCTIONS �� 28

OPTIONAL INFRARED BURNER OPERATION �� 29

SERVICING AND CLEANING �� 30

CLEANING YOUR GRILL �� 30

REPLACING HALOGEN BULBS �� 32

CONTROL PANEL REMOVAL �� 33

SYSTEM RESET �� 34

BURNER(S) REMOVAL �� 34

CONVERT GAS TYPE / CHECK BURNER ORIFICES �� 35

AIR SHUTTER ADJUSTMENT �� 37

TROUBLESHOOTING �� 39

WARRANTY �� 40

4

1. The outdoor appliance and surrounding area MUST

remain clear of ﬂammable substances such as gasoline,

yard debris, wood, etc. Maintain a minimum horizontal

clearance of 18" (in all directions) from combustible

materials/items.

2. Do not block the 1" front air inlet along the bottom of

the control panel. See the COMBUSTION AIR AND

COOLING AIRFLOW section under INSTALLATION

REQUIREMENTS for details.

3. This unit must be installed so that the vent

openings and surrounding area of the grill remain

clear and free at all times. See the GAS SAFETY

INFORMATION section.

4. When using propane gas: the propane cylinder,

regulator, and rubber hose must be in a location

not subject to temperatures above 125° F (51° C).

5. The back burner cover or IR burner cover (if equipped)

must be removed before using the burner.

6. The ﬂames on each burner burn evenly along the

entire burner with a steady ﬂame (mostly blue). If

burner ﬂames are not normal, check and clean the

oriﬁce and burner/venturi tubes for insects and insect

nests. A clogged tube can lead to a ﬁre beneath the

unit. A proper ﬂame pattern will ensure safe operation

and optimal performance. Adjust the air shutter as

needed (see AIR SHUTTER ADJUSTMENT section).

7. The in-line gas valve or gas cylinder valve must always

be shut OFF when the unit is not in use.

8. The drip collector holes must be clear and unobstructed.

Excessive grease deposits can result in a grease ﬁre.

9. Whenever reconnecting any wires, apply a small

amount of dielectric grease to the male connector,

then make the connection. This will ensure conductivity

and prevent moisture from affecting the contact.

10. Wear gloves and use extreme caution whenever

installing and handling this product and its accessories

as certain components have sharp edges that can

cause personal injury.

WARNING: NEVER cover more than 75% of the cooking or grill surface with griddles or pans. Overheating will occur,

and burners will not perform properly when combustion heat is trapped below the cooking surface.

IMPORTANT

IN THE EVENT OF A GREASE FIRE, IMMEDIATELY SHUT OFF THE MAIN GAS VALVE TO THE UNIT. KEEP THE LID

OPEN AND ALLOW THE FIRE TO EXTINGUISH ITSELF. KEEP AT A SAFE DISTANCE. A THOROUGH INSPECTION BY

A QUALIFIED PROFESSIONAL SERVICE TECHNICIAN SHOULD BE CONDUCTED BEFORE FUTURE USE OF YOUR

UNIT. THE SERVICE TECHNICIAN WILL CHECK THE SYSTEM FOR GAS LEAKS AND WILL CHECK ALL ELECTRICAL

WIRING FOR DAMAGE. ALL GAS LEAKS AND WIRING MUST BE REPAIRED PRIOR TO FUTURE USE.

ELECTRICAL CONNECTIONS

A 120VAC (15 AMP minimum) GFCI GROUNDED 3-wire receptacle (not included) is required within

the vicinity of the unit to provide power to it. The GFCI receptacle must be a WEATHER-PROOF IN-USE

COVERED RECEPTACLE.

• Observe the National Electric Code and all local codes.

• Verify proper polarity of the receptacle.

• If an extension cord is used, ensure it is a 3-wire GROUNDED cord that is rated for the power of the

equipment, and is approved for outdoor use with a W-A marking. DO NOT use 2-prong adapters.

• DO NOT TAMPER WITH THE EXTENSION CORD OR THE UNIT POWER-SUPPLY CORD.

Important: ONLY REPLACE THE INTERIOR OVEN LIGHTS WITH 12V / 10 WATT HALOGEN BULB(S).

The unit serial number tag can be found afﬁxed to the grill body behind the control panel (on an

aluminum tag) and on the underside of the drip tray handle (on a thermal label). It is recommended

that the drip tray ﬁrst be removed and cleaned / emptied of its contents, then turned over to view.

The unit rating label is located inside of the control panel.

INSTALLATION, OPERATION, AND SAFETY INFORMATION

5

WARNING

This appliance MUST be installed and operated according to the information below.

FAILURE TO PROPERLY VENT THE PROPANE TANK MAY RESULT IN A FIRE OR EXPLOSION CAUSING

PROPERTY DAMAGE, BODILY INJURY, OR DEATH.

A leaking gas connection or valve unintentionally left open will create a hazard.

WHEN USING PROPANE GAS

• Propane gas (also known as L.P. gas) is heavier than air and will accumulate or pool in an inadequately

vented area or recessed area.

• If a pool of propane gas is ignited, an explosion will occur. Adequate venting at the ﬂoor level of the propane

tank eliminates this danger.

• DO NOT store a spare propane-gas cylinder near the unit.

WHEN USING NATURAL GAS

• Natural gas is lighter than air and will accumulate at the top of an inadequately vented area.

• If an accumulation of natural gas is ignited, an explosion will occur. Adequate venting will eliminate this danger.

INSTALLATION SAFETY GUIDELINES

THIS UNIT MUST BE INSTALLED SO THAT THE AREA AROUND THE UNIT AND PROPANE TANK REMAIN

CLEAR AND FREE AT ALL TIMES.

The gas cylinder, regulator, and rubber hose must be in a location not subject to temperatures above

125° F (51° C).

IF A PROPANE CYLINDER IS INSTALLED, THE GUIDELINES FOUND IN THE SAFE USE & MAINTENANCE

OF PROPANE GAS CYLINDERS SECTION MUST BE FOLLOWED.

WHEN OPERATING THIS GAS APPLIANCE, ALL INSTRUCTIONS AND WARNINGS

MUST BE OBSERVED. FAILURE TO DO SO MAY RESULT IN A FIRE OR EXPLOSION

CAUSING PROPERTY DAMAGE, BODILY INJURY, OR DEATH.

Every time you use the unit, make sure that:

1. The area around the unit is clear and free from combustible materials, gasoline and ﬂammable vapors/liquids.

2. There is no blockage of the airﬂow around the unit and propane tank.

3. The hose is inspected (if applicable). See SAFE USE & MAINTENANCE OF PROPANE-GAS CYLINDERS section.

DO NOT store any combustible materials, gasoline, and any other ﬂammable vapors/liquids in the vicinity of the

unit. Provide adequate clearance for servicing and operation.

GAS SAFETY INFORMATION

OPERATING THE UNIT SAFELY AND CORRECTLY

6

U

L

Fig. 6-1 type coupleur de ﬁl de point culminant d’I

Valve

de

décompression

QCC

Type 1

Valve

Ajustage de précision

en laiton de ﬁl de

point culminant

Indicateur

de niveau

de liquide

(facultatif)

Écrou de main avec le

ﬁl de point culminant.

Régulateur

Passage

Tuyau

Volant de commande

main dans le sens des aiguilles d’une montre pour engager les

ﬁls et pour serrer jusqu’à ce que douillettement. L’utilisation des

pinces ou de la clé ne devrait pas être nécessaire. Seulement

le propane marqué par cylindres doit être employé.

Pour débrancher: Tournez l’écrou de main dans le sens

contraire des aiguilles d’une montre jusqu’à isolé (ﬁg. 6-1).

Important: Avant d’employer le unité, et ensuite chaque

fois que le cylindre est enlevé et rattaché,

examinez tous les raccordements pour

déceler les fuites. Arrêtez les valves de unité

et ouvrez la valve principale de cylindre, puis

vériﬁez les raccordements avec de l’eau

savonneux. Réparez toutes les fuites avant

d’allumer le unité.

ATTENTION: Tournez toujours la valve principale de cylindre

de propane au loin après chaque utilisation,

et avant de déplacer le unité et le cylindre, ou

débrancher l’accouplement. Cette valve doit

rester fermée et le cylindre a débranché alors

que l’appareil n’est pas en service, quoique

l’écoulement de gaz soit arrêté par un dispositif

de sûreté quand le coupleur est débranché.

Inspectez soigneusement l’ensemble de tuyau chaque fois

avant que le gaz soit allumé. Un tuyau ﬁssuré ou efﬁloché doit

être immédiatement remplacé.

Si l'appareil est stocké à l'intérieur, le cylindre doit être disconnected

et a enlevé. Des cylindres Disconnected doivent être stockés

dehors, hors de la portée des enfants, avec les prises de valve

ﬁletées étroitement installées, et ne doivent pas être stockés dans

un bâtiment, le garage, ou n'importe quel autre secteur inclus.

POUR VOTRE SÛRETÉ

a. Ne stockez pas un cylindre de gaz disponible de propane

dessous ou ne vous approchez pas de cet appareil.

b. Ne remplissez jamais cylindre au delà de 80 pour cent de

plein.

c. SI L’INFORMATION DANS “A” ET “B” N’EST PAS SUIVIE

EXACTEMENT, UN FEU CAUSANT LA MORT OU DES

DOMMAGES SÉRIEUX PEUT SE PRODUIRE.

IMPORTANT POUR VOTRE SÛRETÉ

LISEZ ET SUIVEZ TOUS LES AVERTISSEMENTS ÉQUIPÉS DE VOTRE CYLINDRE DE GAZ DE PROPANE.

En actionnant cet appareil avec un cylindre de gaz de propane ON DOIT observer ces instructions et avertissements.

LE MANQUE DE FAIRE AINSI PEUT AVOIR COMME CONSÉQUENCE UNE INCENDIE OU UNE EXPLOSION SÉRIEUSE.

CYLINDRE ET CONDITIONS ET

CARACTÉRISTIQUES DE CONNECTEUR

a. Les bouteilles, les vannes et les tuyaux de propane doivent

être entretenus et inspectés avant chaque utilisation. Ils

doivent être remplacés en cas de dommages visibles. Si

le tuyau est coupé ou présente des signes d’abrasion ou

d’usure, il doit être remplacé avant utilisation (voir e.).

b. Cette unité, lorsqu'elle est utilisée avec une bouteille, doit

être connectée à une bouteille standard de gaz propane de

5 gallons (20 lb) équipée d'un dispositif anti-débordement

répertorié. L’appareil est obligatoire sur toutes les bouteilles

vendues depuis le 1er octobre 1998 aﬁn d’empêcher tout

remplissage excessif.

c. Les dimensions du cylindre doivent être d'environ 12 "(30,5 cm)

de diamètre et 18" (45,7 cm) de hauteur. Les bouteilles doivent

être construites et marquées conformément aux spéciﬁcations

du ministère des Transports (DOT) pour les bouteilles à gaz LP

ou à la norme relative aux bouteilles, sphères et tubes pour le

transport des marchandises dangereuses et à la Commission,

CAN / CSA-B339, selon le cas.

d. Le cylindre doit inclure un collier pour protéger la valve

de cylindre et le circuit d’alimentation de cylindre doit être

assuré le retrait de vapeur.

e. Le montage du régulateur de pression et le ﬂexible (Fig. 6-1)

fourni avec cet appareil au gaz en plein air (modèles au

propane seulement) doit être utilisé. Assemblées d'origine et

régulateur de pression et le tuyau de remplacement doivent

être ceux spéciﬁés par le fabricant pour le raccordement d'un

dispositif de cylindre de liaison identiﬁée comme de type I

par le ANSI Z 21.58/CGA 1.6 (voir liste des pièces pour les

informations de commande).

f. La valve de cylindre de gaz de propane doit être équipée

d’un dispositif d’accouplement de raccordement de

cylindre, décrit comme type I dans la norme déﬁnie dans le

e. de paragraphe ci-dessus. Ce dispositif est généralement

décrit comme coupleur de ﬁl de point culminant.

g. Si votre cylindre de gaz de propane vient avec une prise

de la poussière, placez le bouchon anti-poussière sur la

sortie de valve de cylindre toutes les fois que le cylindre

n’est pas en service.

OPÉRATION DE COUPLEUR

Pour relier le regulator/hose à l’ajustage de précision de

valve de cylindre de gaz de propane: Serrez l’écrou de main

sur le régulateur au-dessus de l’ajustage de précision de ﬁl

de point culminant sur la valve de cylindre. Tournez l’écrou de

1

2

3

4

e. Le régulateur de pression et l’ensemble de tuyau utilisé

doivent assortir les spéciﬁcations pour le type I par ANSI

Z 21.58/CGA 1.6 (voir la ﬁgue. 6-1).

UTILISATION SÛRE ET ENTRETIEN DES CYLINDRES DE GAZ DE PROPANE

7

U

L

Fig. 7-1 Type I Acme thread coupler

Pressure

relief

valve

QCC

Type 1

valve

Brass Acme

thread ﬁtting

Liquid level

indicator

(optional)

Hand nut with Acme

thread

Regulator

Vent

Hose

Hand wheel

The use of pliers or a wrench should not be necessary. Only

cylinders marked “propane” may be used.

To disconnect: Turn the hand nut counterclockwise until

detached (Fig. 7-1).

Important: Before using the unit, and after each time

the cylinder is removed and reattached,

check the hose for wear (see a.) and check

all connections for leaks. Turn off the unit

valves and open the main cylinder valve,

then check connections with soapy water.

Repair any leaks before lighting the unit.

CAUTION: Always turn the propane cylinder main valve

off after each use, and before moving the unit

and cylinder or disconnecting the coupling.

This valve must remain closed and the

cylinder disconnected while the appliance

is not in use, even though the gas ﬂow is

stopped by a safety feature when the coupler

is disconnected.

Carefully inspect the hose assembly each time before the

gas is turned on. A cracked or frayed hose must be replaced

immediately.

If the appliance is stored indoors, the cylinder must be

disconnected and removed. Disconnected cylinders must be

stored outdoors, out of the reach of children, with threaded

valve plugs tightly installed, and must not be stored in a

building, garage, or any other enclosed area.

FOR YOUR SAFETY

a. DO NOT store a spare propane-gas cylinder under or

near this appliance.

b. NEVER ﬁll the cylinder beyond 80-percent full.

c. IF THE INFORMATION IN a. AND b. IS NOT FOLLOWED

EXACTLY, A FIRE CAUSING DEATH OR SERIOUS

INJURY MAY OCCUR.

IMPORTANT FOR YOUR SAFETY

READ AND FOLLOW ALL WARNINGS PROVIDED WITH THE PROPANE-GAS CYLINDER.

When operating this appliance with a propane-gas cylinder, these instructions and warnings MUST be observed.

FAILURE TO DO SO MAY RESULT IN A SERIOUS FIRE OR EXPLOSION.

CYLINDER/CONNECTOR REQUIREMENTS

a. Propane-gas cylinders, valves, and hoses must be

maintained in good condition and inspected before each use

of appliance. They must be replaced if there is any visible

damage. If hose is cut or shows excessive abrasion or wear,

it must be replaced before using appliance (see e.).

b. This unit, when used with a cylinder, should be connected

to a standard 5-gallon (20 lb.) propane-gas cylinder

equipped with a listed overﬁlling prevention device. The

device has been required on all cylinders sold since

October 1,1998, to prevent overﬁlling.

c. Cylinder dimensions should be approximately 12" (30.5

cm) in diameter and 18" (45.7 cm) high. Cylinders must

be constructed and marked in accordance with the U.S.

Department of Transportation (D.O.T.) Speciﬁcations for

LP-Gas Cylinders, or the Standard for Cylinders, Spheres,

and Tubes for Transportation of Dangerous Goods and

Commission, CAN/CSA-B339, as applicable.

d. The cylinder used must include a collar to protect the

cylinder valve, and the cylinder supply system must be

arranged for vapor withdrawal.

e. The pressure regulator and hose assembly (Fig. 7-1)

supplied with this outdoor gas appliance (L.P. models

only) must be used. Original and replacement pressure

regulator and hose assemblies must be those speciﬁed by

the manufacturer for connection with a cylinder connecting

device identiﬁed as Type I by the ANSI Z 21.58/CGA 1.6

(see PARTS LIST for ordering information).

f. The propane-gas cylinder valve must be equipped with

a cylinder connection device, described as Type I in the

standard deﬁned in paragraph e. above. This device is

commonly described as an Acme thread coupler.

g. If the propane-gas cylinder comes with a dust plug, place

the dust cap on the cylinder valve outlet whenever the

cylinder is not in use.

COUPLER OPERATION

To connect the regulator/hose assembly to the propane-

gas cylinder valve ﬁtting: Press the hand nut on the regulator

over the Acme thread ﬁtting on the cylinder valve. Turn the hand

nut clockwise to engage the threads and tighten until snug.

e. The pressure regulator and hose assembly used must

match the speciﬁcation for Type I by ANSI Z 21.58/CGA

1.6 (see Fig. 7-1).

SAFE USE & MAINTENANCE OF PROPANE GAS CYLINDERS

8

Installation must be performed by a qualiﬁed professional

service technician.

This unit is designed for outdoor use only. DO NOT use this

unit inside a building, garage, or enclosed area. DO NOT use

this unit in or on a recreational vehicle or boat.

OVERHEAD CONSTRUCTION AND EXHAUST

HOOD REQUIREMENTS

A minimum 5 foot clearance is required between the cooking

surface and the overhead construction.

When installed under combustible overhead construction,

the area above the cooking surface of the unit must be

covered with an exhaust hood. The exhaust hood provides

the protection for the combustible overhead construction.

See exhaust hood information below and Fig. 8-1.

Important: DO NOT use this appliance under unprotected

combustible overhead construction.

When installed under overhead non-combustible construction,

an exhaust hood is highly recommended; see exhaust hood

information below and Fig. 8-1.

Exhaust Hood

When using an exhaust hood, the area above the cooking

surface of the grill must be covered with a hood larger than

the cooking area of the grill, and with a minimum of 1200

CFM (cubic feet per minute) rated exhaust fan for proper

outdoor application.

INSTALLATION REQUIREMENTS

Fig. 8-1 Overhead requirements

Min.

5'

OVERHEAD CONSTRUCTION

EXHAUST

HOOD

Combustible overhead

construction:

Exhaust hood required

Non-combustible

overhead construction:

Exhaust hood highly recommended

N

O

N

C

O

M

B

U

S

T

I

B

L

E

W

A

L

9

REAR WALL CLEARANCES

For the minimum clearances between the unit and rear walls,

your setup must fall within one (or more) of the following:

A. Clearance between unit and strictly non-combustible

rear wall

(i.e. brick wall, see Fig. 9-1)

• The unit must have a minimum clearance of 4" from

the non-combustible rear wall.

(To allow for proper ventilation and prevent dangerous

overheating.)

B. Clearance between unit and a protected combustible

rear wall

(i.e. a non-combustible wall in front of a combustible wall

to serve as a barrier. This can be accomplished by brick,

or a metal stud ﬁnished with non-combustible substrate,

see Fig. 9-2)

• The unit must have a minimum clearance of 14" from

the protected combustible rear wall.

(The 4" non-combustible material plus an additional 10"

clearance between the unit and protected rear wall.)

C. Clearance between unit and combustible rear wall

• The unit must have a minimum clearance of 18" from

the combustible rear wall (see Fig. 9-3).

SIDE WALL / CORNER WALL CLEARANCES

(if applicable)

The unit must have a minimum clearance of 24" from any

side walls (to account for variables in airﬂow that could affect

performance). See Fig. 9-4.

INSTALLATION REQUIREMENTS (Cont.)

Fig. 9-3 Clearance 'B' Diagram

Combustible

Min.

18"

(Clearance required for

rear wall)

Fig. 9-1 Clearance 'A' Diagram

Non-combustible

Min.

4"

(Clearance required for

rear wall)

Fig. 9-2 Clearance 'B' Diagram

Min.

14"

Non-combustible

substrate

Non-combustible 4"

Com-

bustible

(Clearance required for

rear wall)

Fig. 9-4 Side/corner wall clearance

Min.

24"

10

The control panel MUST remain removable for servicing (see

CONTROL PANEL REMOVAL section).

COMBUSTION AIR AND COOLING AIRFLOW

Proper airﬂow (front-to-back, Fig. 10-) MUST be maintained

for the unit to perform as it was designed. If airﬂow is blocked,

overheating and poor combustion will result. Do not block the

1" front air inlet along the bottom of the control panel.

CAUTION: Wind blowing into or across the rear oven lid

vent (Fig. 10-) can cause poor performance

and/or dangerous overheating. Install the grill

so that the prevailing wind blows toward the

front of the grill (Fig. 10-). A wind deﬂector is

available for purchase to assist in proper

airﬂow during windy conditions. See Table

1 for model numbers. Follow the instructions

included with the wind deﬂector for installation.

GAS-SUPPLY PLUMBING REQUIREMENTS

For natural gas or a household propane system, rigid

1

/

2

" or

3

/

4

" black steel pipe or local code-approved pipe is required

to conduct the gas supply to the unit. Contact your local gas

supplier. Connect this pipe to the C.S.A.-approved quick

connect hose (attached). Apply only joint compounds that are

resistant to all gasses on all NPT pipe ﬁttings except ﬂare

ﬁttings. Make sure to tighten all ﬁttings securely.

Note: If

1

/

2

" pipe is used with natural gas, it should be

no longer than 20'.

Important: A shut-off valve (not included) in the gas

line is required. It provides for safety when

the unit is not in use and for convenient

maintenance and repair. It must be installed

within 6 feet of the unit and must be easily

accessible. Use a pipe joint compound

resistant to all gasses on all male ﬁttings

except ﬂare ﬁttings.

GAS SUPPLY AND MANIFOLD PRESSURES:

For natural gas - normal 7" water column (w.c.), minimum

5", maximum 10

1

/

2

". For propane gas - normal 11" w.c.,

minimum 10", maximum 13".

INSTALLATION REQUIREMENTS (Cont.)

CORRECT

PLACE GRILL SO PREVAILING

WIND BLOWS TOWARD FRONT

OF GRILL

Fig. 10-2 Airﬂow direction - CORRECT

(1" front air inlet)

Fig. 10-1 Airﬂow diagram

YOU MUST PROTECT

REAR OVEN VENT FROM

PREVAILING WIND

Rear oven lid vent

INCORRECT

Fig. 10-3 Airﬂow direction - INCORRECT

11

• To protect against electric shock, do not immerse cord or plugs in water or other liquid.

• Unplug from the outlet when not in use and before cleaning. Allow to cool before putting on or taking off parts.

• Do not operate any outdoor cooking gas appliance with a damaged cord, plug, or after the appliance

malfunctions or has been damaged in any manner. Contact the manufacturer for repair.

• Do not let the cord hang over the edge of a table or touch hot surfaces.

• Do not use an outdoor cooking gas appliance for purposes other than intended.

• When connecting, ﬁrst connect plug to the outdoor cooking gas appliance then plug appliance into the outlet.

• Use only a properly wired and inspected 120VAC (15 AMP minimum) Ground Fault Circuit Interrupter

(GFCI) GROUNDED 3-wire receptacle with this outdoor cooking gas appliance.

• The GFCI receptacle must be a WEATHER-PROOF IN-USE COVERED RECEPTACLE.

• Never remove the grounding plug or use with an adapter of 2 prongs.

• Use only extension cords with a 3 prong grounding plug, rated for the power of the equipment, and approved

for outdoor use with a W-A marking.

• The provisions of the National Electric Code as well as any local codes must be observed when

installing the product.

ELECTRICAL SAFETY

12

A430s

Main burner quantity

N/P oriﬁce drill size

2

#42 / #54

Backburner (if equipped)

N/P oriﬁce drill size

#52 / #59

Infrared searing burner (if equipped)

N/P oriﬁce drill size

#49 / #56

Burner maintenance kit model # (not included) MK-1

Grill complete maintenance kit model # (not included) MCK-1

Wind deﬂector model # (not included) 23728-19

Input electrical requirements 100~240 VAC / 1.90A max. / 50/60 Hz / GFCI outlet

Electrical output 13 VDC / 150 Watts

Oven lights rating 12V / 10 watt halogen bulb

Note: In addition, a wire diagram speciﬁc to your unit can

be found afﬁxed to the inside of the control panel.

Power

supply

Wire harness

extension

Wire harness

assembly

Valve

manifold

Ground

wire

Main burner igniters

POST GRILL WIRING DIAGRAM

Backburner igniter

(if equipped)

Interior

Oven

light

Light

switch

Back burner

(if equipped)

Main

burner 1

Main

burner 2

*

Model wire diagrams may vary.

*

LED disk

(large)

LED disk

(small)

Table 1 - Product Speciﬁcations

Interior

Oven

light

MODEL SPECIFICATIONS

13

Height Width Depth

Floor to top

(with oven)

Floor to top

of shelf

(C)

Left to right Front to back

Post base

(D)

Shelves

(E)

Post base

(F)

Maximum

outer

(G)

Open (A) Closed (B)

57

1

/8" 49

7

/8" 37" 26" 56" 20

1

/4" 26"

Fig. 13-1

G

C

F

E

D

A

B

Table 2 - Post Patio Mount Grill Dimensions

MODEL SPECIFICATIONS (cont.)

14

Fig. 14-1

Ground level

L

K

N

O

J

M

H

I

Height* Width Depth

Floor to top

(with oven)

Floor to

top of

shelf

(J)

Floor to

bottom of

extension

below

ground

(K)

Left to right Front to back

Post

(L)

Shelves

(M)

Post

(N)

Maximum

outer

(O)

Open

(H)

Closed

(I)

57

1

/8" 49

7

/8" 37” 18” 5

1

/2” 56" 5

1

/2” 26"

*Note: Height dimensions are approximate from ground level once installed.

Table 3 - In-Ground Post Grill Dimensions

MODEL SPECIFICATIONS (cont.)

15

10

29

1

2

7

16

17

20

21

19

15

12

18

IMPORTANT

Remove all packing

material and discard prior

to lighting.

9

22

3

To order replacement

parts, contact your

local Fire Magic

®

dealer.

8

28

27

26

45

31

11

Some items shown

are optional, or are not

available for certain

models. Your model

may vary, refer to parts

table.

41

40

5

4

13

30

14

49

24

23

AURORA GRILL REPLACEMENT PARTS LIST

16

A430s

Item Description Part No. Qty.

1.

Stainless cooking grid (set of 2) 3542-DS-2 1

2.

Flavor grid (set of 2) 3063-S-2 1

3.

Main burner 3042-50 2

4.

Flame arrester kit 24177-05 2

5.

Silicone gasket 24177-06 2

6.

Infrared burner *‡ 3065 1

7.

Oven lid w/ oven thermometer 23729-60 1

8.

Warming rack 3672S-B 1

9.

Backburner* 24130-11H 1

10.

Backburner cover* 24148-010 1

11.

Patio base w/ hardware *

†

24330-31 1

or

In-ground base w/ hardware *

†

24330-32 1

12.

Heavy-duty rotisserie motor* 3600-02 1

13.

Heavy-duty rotisserie rod* 3603-30 1

14.

Rotisserie knob* 24187-16 1

15.

Meat holder (pair)* 3613 1

16.

Counterbalance* 3620E 1

17.

Grid lifter 3519 1

18.

Convertible regulator PR-4 1

19.

Valve manifold w/ backburner 24130-22 1

or

Valve manifold w/o backburner 24130-28 1

20.

Control panel w/ backburner 24130-49 1

or

Control panel w/o backburner 24130-50 1

21.

Small knob * 24182-42 1

22.

Large knob 24182-41 2

23.

LED disk (small)* 24182-64 1

24.

LED disk (large) 24182-63 2

A430s

Item Description Part No. Qty.

25.

Oven lid thermometer w/ bezel ‡ 23307

1

26.

Drip tray 3084 1

or

Drip tray w/ match holder 3085 1

27.

Drip tray liner (set of 4) 3557 1

28.

Rigid shelf (left) 24330-017L 1

29.

Rigid shelf (right) 24330-017R 1

30.

Patio mount hardware kit w/ lag

shield and lag screw (if applicable)

24330-25 1

31.

Timer valve (1 hour) 3092B 1

32.

Propane regulator / hose assy. *‡ 5110-07 1

or

Natural Gas QD hose *‡ 5110-03 1

33.

Wire harness assembly‡ 24177-29 1

34.

Backburner electrode*‡ 4199-52 1

35.

Main burner electrode‡ 3199-72 2

36.

Natural gas oriﬁce(s)‡ 3001-42-2 1

37.

Natural backburner gas oriﬁce(s)‡ 3001-52-1 1

38.

Propane gas oriﬁce(s)‡ 3001-54-2 1

39.

Propane backburner gas oriﬁce(s)‡ 3001-59-1 1

40.

Wire harness extension 24182-53 1

41.

Power supply box w/ cord 24182-18 1

42.

12V / 10 watt halogen light bulb ‡ 24187-15 2

43.

Light lens ‡ 24187-26 2

44.

Lamp assembly ‡ 24187-28 2

45.

Light switch 24182-48 1

46.

Backburner ﬂex connector *‡ 3030-01 1

47.

Lighting tube (left) ‡ 24187-29 1

48.

Lighting tube (right) ‡ 24187-35 1

49.

Air bafﬂe

24194-40

1

* If equipped

†

For replacement only (not conversion)

‡ Not shown

AURORA GRILL REPLACEMENT PARTS LIST (cont.)

17

Fig. 17-3 Post base option

INSTALLATION

It is not required to remove the control panel or knobs

to install this unit.

DO NOT lift the unit from the control panel when installing.

PREPARE FOR INSTALLATION

Consult a qualiﬁed professional installer.

The ﬂex connector can be routed out the back of the post,

under the post base, or inside the post. The power supply

cord is to be routed out the back.

To gain access to the inside of the post, unscrew and carefully

open the access plate on the rear of the post using a medium

Phillips-head screwdriver. Retain the screws.

A power supply is pre-mounted to the access plate. For ease

of installation, disconnect the power supply from the wire

harness extension. Locate the wires coming from the inside

of the post to the power supply and carefully disconnect (see

Fig. 17-1 and 17-2).

Important: Pull from the connectors (not the wires).

ROUTE POWER SUPPLY CORD

The power cord will need to be routed through the access plate

for later connection to a 120VAC (15 AMP minimum) GFCI

GROUNDED 3-wire receptacle. The GFCI receptacle must

be a WEATHER-PROOF IN-USE COVERED RECEPTACLE.

1. Remove the knock-out disc at the bottom left of the

access plate with a large ﬂathead screwdriver. (Insert

the screwdriver into the notch provided in the center of

the knock-out.)

2. Remove the plastic power cord bushing attached to the

power cord.

3. Feed the power cord through the newly created hole.

4. Install the bushing onto the power cord and slide the

bushing up against the access plate knock-out hole and

snap into place. See Fig. 17-1.

ROUTE FLEX CONNECTOR

The gas supply line will need to be run to the post install

location as appropriate for the desired setup.

To route ﬂex connector through rear of post:

1. Remove the knock-out disk at the bottom right of the

access plate with a large ﬂathead screwdriver. (Insert

the screwdriver into the notch provided in the center of

the knock-out.)

2. Remove the plastic grommet (attached to the ﬂex

connector) and insert it into the newly created opening.

Then route the ﬂex connector through the opening. See

Fig. 17-1 and 17-2.

To route ﬂex connector beneath post base:

Route the ﬂex connector through the hole found beneath the

center of the post base (see Fig. 17-3).

Fig. 17-1 Access plate view & install orientation

Access

plate

Gas supply

knock-out

(optional)

Power cord

knock-out

Power

supply

Fig. 17-2 Post interior detail

Back of

timer valve

Flex connector

(w/ ﬂare-to-NPT

adapter)

Flex

connector

(w/ ﬂare-

to-NPT

adapter)

Wire

harness

extension

Wire

Connections

PATIO MOUNT INSTALLATION

18

SECURING THE PATIO MOUNT GRILL

Important: BEFORE USE, the patio mount base

must be securely fastened to a stable,

level surface to ensure the grill remains

ﬁxed and upright at all times.

Locate the patio mount base in the planned grill

location and mark the 4 holes. Drill the marked holes

to a

1

/

2

" diameter x 1

1

/

2

" depth. Insert the lag shields

(see PARTS LIST) into the holes, being sure that they

are ﬂush with the ground.

Align the holes on the patio mount base over the lag

shields in the ground. Secure the base with the lag

screws (see PARTS LIST) using a

7

/

16

" nut driver.

CONNECT THE GAS SUPPLY

For household propane or natural gas units:

1. Route the ﬂex connector to the gas supply stub.

2. Turn OFF the gas supply at the source.

3. A shut-off valve is required within 6 feet of the unit.

If shut-off valve is installed in-line:

• Install the supplied ﬂare-to-NPT adapter to the gas

supply (NPT) using a pipe joint compound resistant to

all gasses (see Fig. 18-2, A). Tighten securely.

• Connect the ﬂex connector to the adapter (see Fig.

18-2, A). Tighten securely.

If shut-off valve is connected to end of gas supply stub:

• Connect the ﬂex connector to the shut-off valve (ﬂare)

(see Fig. 18-2, B). Tighten securely.

For propane cylinders:

For connecting a propane unit to a portable propane tank,

read the safety warnings and follow the instructions in the

section SAFE USE AND MAINTENANCE OF PROPANE GAS

CYLINDERS.

Important: An appropriate adapter will be required to connect

the existing ﬂex connector to an L.P. regulator/

hose assembly.

LEAK TEST

Turn all burner control knobs to the OFF position. Turn the gas

supply on. Then carefully check all gas connections for leaks

with a brush and half-soap/half-water solution before lighting.

NEVER USE A MATCH OR OPEN FLAME TO TEST FOR

LEAKS.

RECONNECT POWER SUPPLY WIRES

CAUTION: IMPROPERLY CONNECTED WIRES WILL

CAUSE DAMAGE TO THE GRILL AND MAY

RESULT IN PROPERTY DAMAGE AND/OR

PERSONAL INJURY.

To connect the power supply box, connect the wires coming

from the power supply to the wire harness extension as shown in

Fig. 18-1.

Important: Apply dielectric grease to the male connectors prior

to making any wire connections.

RE-SECURE ACCESS PLATE

Carefully replace the access plate using the four screws,

ensuring all interior components are properly oriented inside

of the grill. Ensure the power supply cord (and ﬂex connector

if applicable) coming out of the rear of the post are properly

situated and the plastic bushing/grommet pieces are secure

in place.

CONNECT POWER CORD

Connect the cord coming from the rear access plate to a

120VAC (15 AMP minimum) GFCI GROUNDED 3-wire

receptacle. The GFCI receptacle must be a WEATHER-

PROOF IN-USE COVERED RECEPTACLE.

Fig. 18-1 Connect: Gas, Wires, Plate, Power

WARNING

Electrical Grounding Instructions:

This appliance is equipped with a three-

pronged (grounding) plug for your protection

against shock hazard and should be plugged

directly into a properly grounded three-

prong receptacle. Do not cut or remove the

grounding prong from this plug.

To 120VAC

(15 AMP min.)

GFCI

GROUNDED

3-wire

receptacle

Fig. 18-2 Connecting to a gas line

Gas supply

(NPT)

Flex

connector

(from grill)

Flare-to-NPT

shut-off

valve*

(end of gas

supply)

NPT-to-NPT

shut-off valve*

(in-line)

Gas supply

(NPT)

Flare-to-NPT

adapter

Flex

connector

(from grill)

* Shut-off valve: required, not included, must

be within 6 feet of unit

A B

-OR-

Wire

Connections

To gas supply

(as applicable, ﬂex

location may vary)

Flare-to-NPT

adapter

Flex

connector

PATIO MOUNT INSTALLATION (cont.)

19

It is not required to remove the control panel or knobs to install

this unit. DO NOT lift the unit from the control panel when

installing.

PREPARE FOR INSTALLATION

Consult a qualiﬁed professional installer / licensed contractor.

The in-ground post is designed primarily for installation with a

permanent underground gas supply. The power supply cord is to

be routed out the back.

To gain access to the inside of the post, unscrew and carefully open

the access plate on the rear of the post using a medium Phillips-

head screwdriver. Retain the screws.

A power supply is pre-mounted to the access plate. For ease of

installation, disconnect the power supply from the wire harness

extension. Locate the wires coming from the inside of the post to

the power supply and carefully disconnect (see Fig. 19-1 and 19-2).

Important: Pull from the connectors (not the wires).

ROUTE POWER SUPPLY CORD

The power cord will need to be routed through the access plate

for later connection to a 120VAC (15 AMP minimum) GFCI

GROUNDED 3-wire receptacle. The GFCI receptacle must be a

WEATHER-PROOF IN-USE COVERED RECEPTACLE.

1. Remove the knock-out disc at the bottom left of the access

plate with a large ﬂathead screwdriver. (Insert the screwdriver

into the notch provided in the center of the knock-out.)

2. Remove the plastic power cord bushing attached to the power

cord.

3. Feed the power cord through the newly created hole.

4. Install the bushing onto the power cord and slide the bushing

up against the access plate knock-out hole and snap into

place. See Fig. 19-1.

ROUTE GAS SUPPLY (UNDERGROUND METHOD)

Note: This section addresses an underground gas supply setup.

To connect through the rear of the post, reference the

ROUTE FLEX CONNECTOR section of PATIO-MOUNT

INSTALLATION, and do not perform the steps until after:

attaching the extension post, and installing the post / pouring

the concrete.

1. After running the underground gas supply (NPT) line to the

planned grill location, dig a hole for the post and extension

approximately 18" deep and 10-12" in diameter.

Note: Run the gas supply line up from the bottom of the hole

(a little off center) so that it reaches to approximately 4"

above ground level.

Note: The actual depth of the hole should be such that the shelf

surface is approximately 36.5" above ground level.

2. Verify that the gas supply line ﬁts through the gas line clearance

hole in the bottom of the post (see Fig. 19-3). The clearance hole is

the larger of the two holes in the bottom of the post and is off center.

3. Verify that the ﬂex connector coming from the inside of the

post will connect properly with the gas supply line.

Ground level

Concrete level

Post

Gas supply (NPT)

route

Fig. 19-1 Access plate view & orientation

Access

plate

Power cord

knock-out

Power

supply

Fig. 19-2 In-ground install orientation

4" (approx.)

18"

(approx.)

3-5"

Wire

harness

extension

Flex connector

(w/ ﬂare-to-NPT adapter)

Gas supply line (NPT)

Fig. 19-3 Post interior detail

Flex connector

(w/ ﬂare-to-NPT

adapter)

Back of timer valve

Wire

Connections

IN-GROUND POST INSTALLATION

20

ATTACH POST EXTENSION

1. Attach the extension to the bottom of the grill post so

that the open portion is toward the back of the grill and

the ﬁve holes in the extension line up with the ﬁve (5)

weld-nuts in the post (see Fig. 20-1).

2. From outside the joined post and extension, insert

one of the

1

/

4

X 20"-

5

/

8

bolts (supplied) into each of

the ﬁve (5) bolt holes and tighten each using a

7

/

16

"

socket driver or wrench (see Fig. 20-2).

Note: There is one hole on each side of the post,

except the back which has two holes located on

either side of the extension opening.

PLACE POST IN-GROUND & POUR

CONCRETE

1. Prepare the concrete to be used for the install.

2. Carefully orient the post over the gas supply line and

into the installation hole.

Important: Verify that the gas supply line is running up

through the post hole, just off center. It must

extend high enough to reach the grill gas

connection and remain safely above the level

of the concrete when poured.

3. Remove the post, then cover the end of the gas supply

line with a plastic bag and/or masking tape to avoid

getting concrete or other debris in the supply line.

4. Pour the concrete into the hole 3-5" below ground

level taking care to protect the gas supply line.

5. While the concrete is still wet, carefully lower the

extended grill post into the hole so that the gas

supply line slides through the clearance hole in the

bottom of the post.

6. Orient the grill per plan, then level the grill and support

it so that it remains in position while the concrete drys.

ROUTE FLEX CONNECTOR (ABOVE GROUND

METHOD ONLY)

Note: This section addresses an above ground gas

supply setup. If connecting underground, skip this

section and continue with installation.

The gas supply line (NPT) will need to be run to the post

install location as appropriate for the desired setup.

To route ﬂex connector through rear of post:

1. Remove the knock-out disk at the bottom of the access

plate with a large ﬂathead screwdriver. (Insert the

screwdriver into the notch provided in the center of

the knock-out.)

2. Remove the plastic grommet (attached to the ﬂex

connector) and insert it into the newly created opening.

Then route the ﬂex connector through the opening.

See Fig. 20-4.

Bolts

Weld-nut

To grill

Post

Extension

(position

open side

toward back)

Install

provided bolts

into 5 holes

around post

Fig. 20-1 Install extension to post

Fig. 20-2 Fasten extension to post

Ground level

Concrete level

Post

Gas supply route (NPT)

Fig. 20-3 Pour concrete & install post

3-5"

Gas supply line (NPT)

(cover to protect)

Flex connector

(w/ ﬂare-to-NPT adapter)

Fig. 20-4 Access plate view & install orientation

Access

plate

Gas supply knock-out

(grommet installed)

Flex connector

(w/ ﬂare-to-NPT

adapter)

IN-GROUND POST INSTALLATION (cont.)

La page est en cours de chargement...

Fire Magic Aurora Stand-Alone Post Grill Manuel utilisateur

Fire Magic Aurora Stand-Alone Post Grill Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents