TEAC SL-D930 Le manuel du propriétaire

SL

-

D930

Z

D01206920B

BLUETOOTH CD RADIO

OWNER'S MANUAL

MODE D’EMPLOI

MANUAL DEL USUARIO

ENGLISH FRANÇAIS ESPAÑOL

2

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK). NO USER-

SERVICEABLE PARTS INSIDE. REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

M

The lightning flash with arrowhead in an equi-

lateral triangle is intended to alert the user to

the presence of uninsulated “dangerous volt-

age” within the product’s enclosure that could

be of sufficient magnitude to constitute a risk

of electric shock to persons.

V

The exclamation point in an equilateral tri-

angle is intended to alert the user to the

presence of important operating and mainte-

nance (servicing) instructions in the literature

accompanying the appliance.

IMPORTANT SAFETY PRECAUTIONS

WARNING: TO PREVENT FIRE OR SHOCK

HAZARD, DO NOT EXPOSE THIS APPLIANCE

TO RAIN OR MOISTURE.

CAUTION

o DO NOT REMOVE EXTERNAL CASES OR CABINETS TO

EXPOSE THE ELECTRONICS. NO USER SERVICEABLE

PARTS ARE INSIDE.

o IF YOU ARE EXPERIENCING PROBLEMS WITH THIS

PRODUCT, CONTACT THE STORE WHERE YOU

PURCHASED THE UNIT FOR A SERVICE REFERRAL. DO

NOT USE THE PRODUCT UNTIL IT HAS BEEN REPAIRED.

o USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE

OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN

COULD RESULT IN HAZARDOUS RADIATION EXPOSURE.

IN USA/CANADA, USE ONLY ON 120 V SUPPLY.

3

This product contains a semiconductor laser system

inside the cabinet and is classified as a “CLASS 1 LASER

PRODUCT”.

To prevent being exposed to the laser beam, do not try to

open the enclosure.

Laser:

Type: EP-C101

Manufacturer: GUANGDONG EVER BRIGHT GROUP

CO.,LTD.

Laser output: Less than 0.3 mW

Wavelength: 790 ± 25 nm

Model for USA

This product has been designed and manufactured accord-

ing to FDA regulations “title 21, CFR, chapter 1, subchapter J,

based on the Radiation Control for Health and Safety Act of

1968”, and is classified as class laser product. There is not

hazardous invisible laser radiation during operation because

invisible laser radiation emitted inside of this product is

completely confined in the protective housings.

The label required in this regulation is as follows:

Q Precautions concerning batteries

Misuse of batteries could cause them to rupture or leak

leading to fire, injury or the staining of nearby things.

Please read and observe the following precautions

carefully.

o Be sure to insert the batteries with correct positive

(+) and negative (_) orientations.

o Use batteries of the same type. Never use different

types of batteries together.

o If the remote control is not used for a long time (more

than a month), remove the batteries to prevent them

from leaking.

o If the batteries leak, wipe away the leakage inside

the battery compartment and replace the batteries

with new ones.

o Do not use batteries of types other than those speci-

fied. Do not mix new batteries with old ones or use

different types of batteries together.

o Do not heat or disassemble batteries. Never throw

batteries into fire or water.

o Do not carry or store batteries with other metallic

objects. The batteries could short circuit, leak or

explode.

o Never recharge a battery unless it is confirmed to be

a rechargeable type.

Q WARNING

DO NOT INGEST BATTERY, CHEMICAL BURN HAZARD

o This product contains a coin/button cell battery. If the

coin/button cell battery is swallowed, it can cause severe

internal burns in just 2 hours and can lead to death.

o Keep new and used batteries away form children. If the

battery compartment does not close securely, stop using

the product and keep it away from children.

If you think batteries might have swallowed or placed

inside any part of the body, seek immediate medical

attention.

4

IMPORTANT SAFETY INSTRUCTIONS

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with dry cloth.

7) Do not block any ventilation openings. Install in accor-

dance with the manufacturer's instructions.

8) Do not install near any heat sources such as radiators,

heat registers, stoves, or other apparatus (including

amplifiers) that produce heat.

9) Do not defeat the safety purpose of the polarized or

grounding-type plug. A polarized plug has two blades

with one wider than the other. A grounding type plug

has two blades and a third grounding prong. The wide

blade or the third prong are provided for your safety. If

the provided plug does not fit into your outlet, consult

an electrician for replacement of the obsolete outlet.

10) Protect the power cord from being walked on or

pinched particularly at plugs, convenience receptacles,

and the point where they exit from the apparatus.

11) Only use attachments/accessories specified by the

manufacturer.

12) Use only with the cart, stand, tri-

pod, bracket, or table specified by

the manufacturer, or sold with the

apparatus. When a cart is used, use

caution when moving the cart/

apparatus combination to avoid

injury from tip-over.

13) Unplug this apparatus during lightning storms or when

unused for long periods of time.

14) Refer all servicing to qualified service personnel.

Servicing is required when the apparatus has been

damaged in any way, such as power-supply cord or

plug is damaged, liquid has been spilled or objects

have fallen into the apparatus, the apparatus has been

exposed to rain or moisture, does not operate nor-

mally, or has been dropped.

o

The apparatus draws nominal non-operating power

from the AC outlet with its POWER or STANDBY/ON

switch not in the ON position.

o

The mains plug is used as the disconnect device, the

disconnect device shall remain readily operable.

o

Caution should be taken when using earphones or

headphones with the product because excessive sound

pressure (volume) from earphones or headphones can

cause hearing loss.

CAUTION

o

Do not expose this apparatus to drips or splashes.

o

Do not place any objects filled with liquids, such as

vases, on the apparatus.

o

Do not install this apparatus in a confined space such

as a book case or similar unit.

o

The apparatus should be located close enough to the

AC outlet so that you can easily reach the power cord

plug at any time.

o

If the product uses batteries (including a battery pack

or installed batteries), they should not be exposed to

sunshine, fire or excessive heat.

o

CAUTION for products that use replaceable lithium

batteries: there is danger of explosion if a battery is

replaced with an incorrect type of battery. Replace

only with the same or equivalent type.

The Bluetooth® word mark and logos are registered trade-

marks owned by Bluetooth SIG, Inc. and any use of such

marks by TEAC is under license.

This product is protected by certain intellectual property

rights of Microsoft. Use or distribution of such technology

outside of this product is prohibited without a license from

Microsoft.

MPEG Layer-3 audio coding technology licensed from

Fraunhofer IIS and Thomson.

Other company names and product names in this docu-

ment are the trademarks or registered trademarks of their

respective owners.

55

ENGLISH

Wireless equipment precautions (1)

Compliance of radio transmitter

and interference

Model for USA

This device complies with Part.15 of FCC Rules.

Operation is subject to the following two conditions:

1) This device may not cause interference

2) This device must accept any interference, including

interference that may cause undesired operation of the

device.

Labeling of authorization

FCC ID: XEGSL-D930

Model for Canada

Compliance of radio transmitter

This device complies with Industry Canada RSS standard(s)

Operation is subject to the following two conditions:

1) This device may not cause interference

2) This device must accept any interference, including

interference that may cause undesired operation of the

device.

Labeling of authorization

IC: 1559C-SLD930

Compliance of interference

This ClassB digital apparatus complies with Canadian

ICES-003.

Model for EEA (European Economic Area)

This equipment complies with the harmonised standards

of DIRECTIVE 1999/5/EC (R&TTE).

Labeling of conformity

CE marking:

CAUTION

Changes or modifications not expressly approved by the

party responsible for compliance could void the user’s

authority to operate the equipment.

CAUTION

Authorization of wireless devices are different in countries

or regions. Please use only in the country where you pur-

chased the product.

o Depending on the country, restrictions on the use of

Bluetooth wireless technology might exist.

Confirm the laws and regulations of the country or region

where you want to use the unit before use.

Radiation Exposure requirements

This equipment meets the regulation, which is recognized

internationally, for the case of human exposure to radio

waves generated by the transmitter.

Continued on the next page

66

Bluetooth® notes

Wireless equipment precautions (2)

When using this unit with a mobile phone or other

Bluetooth devices, they should be no more than about

10 m (33 ft) apart. Depending on the circumstances of

use, however, the effective transmission distance might be

shorter.

Wireless communication with every device that supports

Bluetooth wireless technology is not guaranteed.

To determine the compatibility between this unit and

another device that supports Bluetooth wireless technology,

refer to that device's operation manual or contact the shop

where you purchased it.

Statement of compliance

Model for USA

This equipment complies with FCC radiation exposure

limits set forth for an uncontrolled environment and

meets the FCC radio frequency Exposure Guidelines.

Model for Canada

This equipment complies with IC RSS-102 radiation expo-

sure limits set forth for an uncontrolled environment.

EEA (European Economic Area) model

This equipment complies with EN.62311; Assessment of

electronic and electrical equipment related to human

exposure restrictions for electromagnetic fields; the har

-

monised standard of DIRECTIVE 1999/5/EC.

Information for interference (FCC

requirements)

This equipment has been tested and found to comply with

the limits for a Class B digital device, pursuant to Part 15 of

the FCC Rules. These limits are designed to provide reason-

able protection against harmful interference in a residential

installation.

This equipment generates, uses, and can radiate radio fre-

quency energy and, if not installed and used in accordance

with the instructions, may cause harmful interference to

radio communications.

However, there is no guarantee that interference will not

occur in a particular installation.

If this equipment does cause harmful interference to radio

or television reception, which can be determined by turn-

ing the equipment off and on, the user is encouraged to

try to correct the interference by one or more of the fol-

lowing measures.

o Reorient or relocate the equipment and/or the receiv-

ing antenna.

o Increase the separation between the equipment and

receiver.

o Connect the equipment into an outlet on a circuit dif-

ferent from that to which the receiver is connected.

o Consult the dealer or an experienced radio/TV techni-

cian for help.

77

ENGLISH

For European Customers

Disposal of electrical and electronic equipment

(a) All electrical and electronic equipment should be

disposed of separately from the municipal waste

stream via collection facilities designated by the

government or local authorities.

(b) By disposing of electrical and electronic equipment

correctly, you will help save valuable resources and

prevent any potential negative effects on human

health and the environment.

(c) Improper disposal of waste electrical and electronic

equipment can have serious effects on the

environment and human health because of the

presence of hazardous substances in the

equipment.

(d) The Waste Electrical and Electronic

Equipment (WEEE) symbol, which shows

a wheeled bin that has been crossed out,

indicates that electrical and electronic

equipment must be collected and

disposed of separately from household waste.

(e)

Return and collection systems are available to end

users. For more detailed information about the

disposal of old electrical and electronic equipment,

please contact your city office, waste disposal service

or the shop where you purchased the equipment.

Disposal of batteries and/or accumulators

(a) Waste batteries and/or accumulators should be

disposed of separately from the municipal waste

stream via collection facilities designated by the

government or local authorities.

(b) By disposing of waste batteries and/or accumulators

correctly, you will help save valuable resources and

prevent any potential negative effects on human

health and the environment.

(c)

Improper disposal of waste batteries and/or

accumulators can have serious effects on the

environment and human health because of the

presence of hazardous substances in them.

(d)

The WEEE symbol, which shows a wheeled

bin that has been crossed out, indicates

that batteries and/or accumulators must be

collected and disposed of separately from

household waste.

If a battery or accumulator contains more than the

specified values of lead (Pb), mercury (Hg), and/or

cadmium (Cd) as defined in the Battery Directive

(2006/66/EC), then the chemical symbols for those

elements will be indicated beneath the WEEE symbol.

(e) Return and collection systems are available to end

users. For more detailed information about the

disposal of waste batteries and/or accumulators,

please contact your city office, waste disposal

service or the shop where you purchased them.

Pb, Hg, Cd

88

Contents Before use

Included items

Check to be sure the box contains all the included items

shown below.

Please contact the store where you purchased this unit if any

of these items are missing or have been damaged during

transportation.

Remote control (RC-1311) × 1

Batteries for remote control (AAA) × 2

Battery for memory back-up (CR2032) × 1

Stereo mini-plug cable × 1

Owner's Manual (this document) × 1

o Keep this manual in a safe place for future reference.

Wireless equipment precautions ..........................5

Bluetooth® notes .........................................6

Before use ................................................8

Discs ....................................................10

MP3/WMA files ..........................................12

About the ErP (only for Europe) ..........................12

Using the remote control ................................13

Connections .............................................14

Names and functions of parts (main unit) ................16

Names and functions of parts (remote control) ...........19

Setting the clock. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

Basic operation ..........................................22

Listening to a CD/MP3/WMA disc ........................24

Playback .................................................25

MP3/WMA file playback order ............................27

Programmed playback ...................................28

Repeat, shuffle and intro playback .......................31

Listening to a connected device .........................33

Listening to a Bluetooth device ..........................34

Pairing with another Bluetooth device ...................35

Listening to the radio ....................................36

Preset tuning ............................................37

RDS (only for Europe) ....................................38

PTY search (only for Europe) .............................39

Sleep timer ..............................................41

Wakeup timer ...........................................41

Troubleshooting .........................................45

Specifications ............................................48

99

ENGLISH

Precautions for use

o Avoid placing the unit in direct sunlight or close to

any source of heat, such as a radiator, heater, open

fireplace or amplifier. Also avoid locations that are sub-

ject to vibrations or exposed to excessive dust, cold or

moisture.

o As the unit could become warm during operation,

always leave sufficient space around it for ventilation.

When installing this unit, leave a little space (at least

20 cm or 8") between it and walls and other devices in

order to allow good heat dissipation. When placing it in

a rack, for example, leave at least 12 cm (5") open above

it and 10 cm (4") open behind it. Failure to provide these

gaps could cause heat to build up inside and result in fire.

o DO NOT place anything, not even CDs, CD-Rs, LP

records or cassette tapes, on top of the unit. Doing so

could damage these items.

o Do not put cloth on top of the unit or place the unit on

top of bedding or thick carpets. Doing so could cause

the unit to overheat and damage it.

o DO NOT MOVE THE UNIT DURING PLAYBACK

During playback, the disc rotates at high speed. Do not

lift or move the unit during playback. Doing so may

damage the disc or the unit.

o WHEN MOVING THIS UNIT

Always remove the disc before relocating or moving

this unit. Moving the unit with a disc inside could cause

a malfunction.

o The voltage supplied to the unit should match the volt-

age as printed on the rear panel. If you are in any doubt

regarding this matter, consult an electrician.

o Do not open the body of the unit as this might result

in damage to the circuitry or cause electric shock. If a

foreign object should get into the unit, contact your

dealer.

o When removing the power plug from the wall outlet,

always pull directly on the plug, never yank on the cord.

o When the unit is turned on, if a TV is turned on nearby

lines might appear on its screen depending on the

characteristics of the TV broadcast signal. This is not a

malfunction of the unit nor of the TV. If this occurs, press

the STANDBY/ON button to put the unit in standby.

o This unit consumes energy when in standby.

Product registration

Customers in the USA, please visit the following TEAC web-

site to register your TEAC product online:

http://audio.teac.com/support/registration/

Maintenance

If the surface of the unit gets dirty, wipe it with a soft cloth

or use diluted mild liquid soap. Allow the surface of the

unit to dry completely before using.

Do not use chemical cleaning cloths, thinner or similar sub-

stances as they could damage the surface of the unit.

V

CAUTION

For safety, disconnect the power cord from the

socket before cleaning.

1010

Discs

Discs that can be played on this unit

CDs with the Compact disc Digital Audio logo

CD-R and CD-RW discs that have been created in

the audio CD format and finalized correctly.

CD-R and CD-RW discs that have been written with

MP3 or WMA files and finalized.

This unit can play the above types of discs (without adapt-

ers). This unit cannot play any other types of discs.

V

CAUTION

If you try to play any other type of disc with this

unit, loud noises that damage speakers or harm

hearing could occur. Never try to play any other

type of disc with this unit.

o This unit might not be able to properly play back Copy

Control CDs, Dual Discs and other special CDs that do

not conform to the Red Book CD standard. Operation

and sound quality cannot be guaranteed when special

discs are used in this unit. If playback of a special disc

should cause trouble, contact the seller of the disc.

CD-R/CD-RW discs

This unit can play back CD-R and CD-RW discs that have

been recorded in the audio CD format (CD-DA) and the

MP3 or WMA format.

o Discs created by a CD recorder must be finalized with

the CD recorder that was used to create the discs before

being used with this unit.

o Depending on disc quality and recording conditions,

playback of some discs might not be possible.

o If you are uncertain about the handling of a CD-R or

CD-RW disc, please contact the seller of the disc directly.

Precautions for use

o Do not use cracked discs because they could damage

the unit.

o When writing something on the label side of a disc, use

a felt tip permanent marker. The use of a ballpoint pen

or other pen with a hard tip could damage the disc,

making it unplayable.

o Never use commercially-available CD stabilizers. Doing

so could make the disc unplayable or damage the unit.

o Never use CDs with irregular shapes, including heart-

shaped and octagonal discs because such discs could

damage the unit.

1111

ENGLISH

Storage precautions

o Discs should be stored in their cases when not being

used. Failure to do so could result in warping and

scratches.

o Do not leave discs in places that are exposed to direct

sunlight or that are very humid or hot. Long exposure

to such conditions could warp or degrade discs, making

them unplayable.

o Since CD-R/CD-RW discs are more susceptible to the

effects of heat and ultraviolet rays compared to com-

mercial CDs, do not leave them for long periods of time

in places that are, for example, exposed to direct sun-

light or near equipment that generate heat.

o Smudges on a disc might cause the sound to skip or

degrade the sound quality. Always clean discs before

storing them.

Maintenance

o If the side of the disc that has the data encoded on

it (unlabeled side) becomes dirty with fingerprints or

dust, use a soft cloth to wipe the surface from the cen-

ter directly toward the edge.

o Never use record cleaners, antistatic treatments, thin-

ners or similar chemicals to clean discs. Such chemicals

could harm the surface of the disc.

Handling precautions

o Always insert the disc into the disc tray with the label

side up. Only one side of a Compact Disc can be played

or used for recording.

o If the side of the disc that the signal is recorded on

(unlabeled side) has scratches, fingerprints or dirt on it,

for example, playback errors could occur. Please handle

discs with care.

o To remove a disc from its case, press down on the cen-

ter of the case and hold the disc by its edges. Do not

touch the side of the disc that has the data encoded on

it (unlabeled side).

Removal from case Holding by edges

1212

This unit can play MP3 and WMA files that are on CD-R/

CD-RW discs.

o Audio file formats that can be played back

MP3 (file extension: .mp3)

Bit rate: 16 kbps to 320 kbps

Sampling frequency: 16 kHz, 22.05 kHz, 24 kHz, 32 kHz,

44.1 kHz, 48 kHz

WMA (file extension: .wma)

Bit rate: 16 kbps to 320 kbps

Sampling frequency: 16 kHz, 22.05 kHz, 24 kHz, 32 kHz,

44.1 kHz, 48 kHz

Note: Digital Rights Management (DRM) is not supported.

File information shown on the display

The display of this unit can only show single-byte alphanu-

meric characters.

o If the file information uses Japanese, Chinese or other

double-byte characters, playback is possible but the

name will not be shown correctly.

Precautions when using computers

and other devices to create files

o Always include the extension in the file name. Files

without extensions cannot be played.

o After recording to a CD-R/CD-RW, always close the ses-

sion (complete disc creation). This unit cannot play a

disc if its session has not been closed.

o A maximum of 999 files and 99 folders on a disc can be

played. If the media has more than these maximums,

this unit might not be able to correctly play any file that

is the 1000th or higher or any folder that is the 100th or

higher.

MP3/WMA files

About the ErP (only for Europe)

This product is compliant with the European ErP Standby

Power Regulation. In order to comply with this regulation,

the automatic power saving function of this unit is set to

ON when shipped new, so the unit will automatically enter

standby if there is no audio output for about 30 minutes.

o When AUX is selected, the unit will automatically enter

standby if there is no input for eight hours.

If you want to disable the automatic power saving func-

tion, do the following.

1) Connect the AC power cord.

2) Press the STANDBY/ON button.

3) Press the FUNCTION button to select “AUX”.

4) Press and hold the play/pause (7/9) button for at

least two seconds.

5) When “ERP-ON” is displayed, press a skip (.m or

,/) button to select “ERP-OFF”.

6) Press the play/pause (7/9) button to exit setting mode.

1313

ENGLISH

Precautions for use

o When using the remote control, point it toward the

remote control signal receiver on the main unit from a

distance of 5 m (16 ft) or less. Do not place obstructions

between the main unit and the remote control.

o The remote control might not work if the remote

control signal receiver on the main unit is exposed to

sunlight or bright lights. In this case, try moving the

main unit.

o Beware that use of this remote control could cause the

unintentional operation of other devices that can be

controlled by infrared rays.

Installing batteries

Remove the cover on the back of the remote control, and

insert 2 AAA batteries into the case, aligning them with

the

¥

and

^

indications. Replace the cover.

Misuse of batteries could cause them to rupture or

leak, which might result in fire, injury or the staining

of nearby materials. Please read and observe the pre-

cautions on page 3 carefully.

Using the remote control

When to replace batteries

If the distance required between the remote and main unit

decreases or if the unit stops responding to the remote

buttons, replace both batteries with new ones.

Dispose of the used batteries according to the instructions

on them or requirements set by your local municipality.

1414

Connections

V

Do not turn the unit on until after making all connections.

o Carefully read the manuals of the devices that you are connecting and follow their instruc-

tions when making connections.

o Do not bundle connecting cables with power cords. Doing so could cause noise.

These illustrations are of the model for Europe.

Front

Rear

C

D

A

B

E

123

1515

ENGLISH

A

PHONES jack

To listen with headphones, first minimize the volume.

Then, insert the headphones’ plug into the PHONES

jack and gradually increase the volume. No sound will

be output from the speakers while the headphones’

plug is inserted in the PHONES jack.

V

CAUTION

Always turn the volume down before plugging

in headphones and putting them on. Do not

connect or disconnect headphones or turn the

unit on or put it in standby while wearing them.

Sudden loud noises could occur, which might

cause hearing damage.

B

AUX IN jack

You can connect a portable audio player to this jack.

Connect it to the audio output jack (LINE OUT or

PHONES) of the player using the included stereo mini

plug cable.

o When using the PHONES jack of an audio player,

you must also adjust the volume of that audio

player or you might hear no sound from this unit.

o If you raise the volume level of the connected

device too high, the sound might distort. If this

occurs, lower the volume of the connected device

until distortion stops and then adjust the volume

on this unit.

C

FM antenna

Extend the lead to find the best position for FM broad-

cast reception.

This antenna may need to be repositioned if you

move your unit to a new location.

D

AC power cord

After completing all other connections, plug the

power plug into the power outlet.

Unplug the power cord from the outlet when you are

not planning to use the unit for an extended period

of time.

V

CAUTION

Be sure to connect the power cord to an AC out-

let that supplies the correct voltage. Connection

to an outlet that supplies incorrect voltage could

cause fire or electric shock. Hold the power plug

when plugging it into an outlet or unplugging it.

Never pull or yank on the power cord.

E

Battery compartment

This contains a battery used to temporarily back up

the unit’s clock, FM/AM radio station presets and

wakeup timer settings during power outages and

when the power cord is unplugged.

Battery installation

Loosen the battery cover screw. Push the other end of

the cover to open the compartment. Insert a CR2032

lithium-ion battery with the positive (

¥

) side facing

the cover. Close the cover.

When to replace the battery

If the clock begins to indicate the wrong time, replace

the battery with a new one.

Dispose of the used batteries according to the instruc-

tions on them or requirements set by your local

municipality.

V

CAUTION

Misuse of batteries could cause them to rupture

or leak, which might result in fire, injury or the

staining of nearby materials. Please read and

observe the precautions on page 3 carefully.

1616

Names and functions of parts (main unit) (1)

Top Rear

Front

These illustrations are of the model for Europe.

D G HE

S R

Q

O

N

M

I K L

C

A

B

F J

P

1717

ENGLISH

A

Disc compartment cover

Push the - mark on the cover to raise the cover.

B

SNOOZE button

When the wakeup timer is on, press this button to put

the unit in standby for 5 minutes.

You can also use this button to change the brightness

of the display.

C

BASS CONTROL knob

Use to adjust the volume of the built-in subwoofer

(low frequencies).

D

PROGRAM button

Use for CD programmed playback (page 28).

Use this button to store AM and FM preset stations in

memory (page 37).

E

FM MODE/PLAY MODE button

When listening to FM radio, use this button to switch

between stereo and mono.

Use to switch between the CD playback modes:

repeat, shuffle and intro (which plays only the begin-

nings of songs one after another) (page 31).

F

Remote control signal receiver

Signals sent from the remote control are received

here. When using a remote, point it toward this spot.

G

FUNCTION button

Press this button to cycle through playback sources in

the following order.

CD BLUETOOTH

FM AM AUX

o Press when the unit is off (standby) to turn it on.

H

DISPLAY/PTY button (Model for Europe)

DISPLAY button (Model for USA/Canada)

Use to search for stations by program type (Model for

Europe only).

Each time you press this button, the information

shown on the display changes (page 26).

I

INFO/RDS button (Model for Europe)

INFO button (Model for USA/Canada)

When listening to FM radio, use this button to select

an RDS mode (Model for Europe only) (page 38).

Press this button when playing a disc that contains

MP3/WMA files to show song names and other ID tag

information (page 27).

Continued on the next page

1818

J

Display

This shows the clock time, song names and other

information.

K

CLOCK ADJUST button

Use this button to adjust the clock (page 21).

L

TIMER button

Use this button to set the wakeup timer (page 41).

M

Speakers (stereo)

N

SLEEP button

Use this button to set the sleep timer (page 41).

O

TUNING knob

Use to select radio (AM, FM) stations (page 36).

When playing a disc that contains MP3/WMA files, use

to select the folder.

Names and functions of parts (main unit) (2)

P

CD player/Bluetooth device operation

buttons

Use to operate the CD player/Bluetooth device.

Stop (8) button

Press to stop playback.

Play/pause (y/9) button

Press to start or pause playback.

When the function is FM, AM or AUX, press this button

to switch to CD. If a disc is loaded, playback will start. If

no disc is loaded, “NO DISC” will appear on the display.

Skip/search (.m/,/) buttons

Use to select tracks/files. Press the .m or

,/ button to skip to the previous or next track

or file when playing back or paused (page 25).

During playback, press and hold the ,/ button

to search forward or the .m button to search

backward (page 25).

When radio stations (AM, FM) have been preset, use to

select them (page 37).

Q

STANDBY/ON button

Press this button to turn the unit on or put it in standby.

R

VOLUME knob

Use this knob to adjust the volume. Turn up to raise

the volume or down to lower the volume.

S

PAIRING button

Press to pair the unit with other Bluetooth devices

(page 35).

o Press when the unit is off (standby) to turn it on

and activate Bluetooth mode.

1919

ENGLISH

Names and functions of parts (remote control) (1)

a

FM MODE)/

PLAY MODE button

When listening to FM radio, use this button to switch

between stereo and mono.

Use to switch between the CD playback modes:

repeat, shuffle and intro (which plays only the begin-

nings of songs one after another) (page 31).

b

PAIRING button

Press to pair the unit with other Bluetooth devices

(page 35).

o Press when the unit is off (standby) to turn it on

and activate Bluetooth mode.

c

Number buttons (1-0)

Use to select CD tracks for playback (page 26).

Use these buttons to select preset stations (page 37).

d

INFO button

When listening to FM radio, use this button to select

an RDS mode (Model for Europe only).

Press this button when playing a disc that contains

MP3/WMA files to show song names and other ID tag

information (page 27).

e

PROGRAM button

Use for CD programmed playback (page 28).

Use this button to store AM and FM preset stations in

memory (page 37).

When both the main unit and the remote control have

buttons with the same functions, this manual explains

how to use either of them. The corresponding buttons

can be used in the same manner.

b

c

d

f

g

h

j

i

m

n

k

p

l

o

a

e

Continued on the next page

2020

Names and functions of parts (remote control) (2)

f

MP3 FOLDER/PRESET (5/b) button

When playing a disc that contains MP3/WMA files, use

to select the folder.

Use these buttons to select preset stations (page 37).

g

VOLUME buttons

Use these buttons to adjust the volume.

h

STANDBY/ON ( ) button

Press this button to turn the unit on or put it in standby.

i

DISPLAY button

Each time you press this button the information

shown on the display changes (page 26).

j

FUNCTION button

Press this button to cycle through playback sources in

the following order.

CD BLUETOOTH

FM AM AUX

o Press when the unit is off (standby) to turn it on.

k

TIMER button

Use this button to set the wakeup timer (page 41).

l

SLEEP button

Use this button to set the sleep timer (page 41).

m

TUNING (5/b)

skip/search (.m/,/) buttons

Use to select radio (AM, FM) stations.

Use to select tracks on a CD or Bluetooth device. Press

the .m or ,/ button to skip to the previ-

ous or next track or file when playing back or paused.

During playback, press and hold the ,/ button

to search forward or the .m button to search

backward.

n

Play/pause (y/9) button

Start or pause playback of a CD or Bluetooth device.

When the function is FM, AM or AUX, press this button

to switch to CD. If a disc is loaded, playback will start. If

no disc is loaded, “NO DISC” will appear on the display.

o

BAND/ stop (8) button

When listening to the radio, use this button to switch

between AM and FM radio bands.

Stop playback of a CD or Bluetooth device.

p

MUTING button

Use this button to mute the sound.

La page charge ...

TEAC SL-D930 Le manuel du propriétaire

TEAC SL-D930 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents