Ashley Hearth Products APC4000B Manuel utilisateur

Marque: Ashley Hearth Products

Modèle: APC4000B

Catégorie: Cheminées

Taper: Manuel utilisateur

Ce manuel convient également à

U. S. Stove

227 Industrial Park Road

P.O. Box 151 South

Pittsburg, TN 37380

(800) 750-2723 852400B-4301F

OWNER’S MANUAL

Classic Cast APC4000

• WARNING: If your appliance is not properly installed a house fire may result. For your safety,

follow the installation directions. Contact local building or fire officials about restrictions and

installation inspection requirements in your area.

• PLEASE read this entire manual before installation and use of this pellet fuel-burning room heater.

Failure to follow these instructions could result in property damage, bodily injury, or even death.

• Save these instructions.

PROFESSIONAL INSTALLATION IS HIGHLY RECOMMENDED

The French version is available for download from the site U.S. Stove: http://www.usstove.com/ La version

française est disponible pour téléchargement à partir du site U.S. Stove: http://www.usstove.com/

U.S. Environmental Protection Agency

Certied to comply with 2015 particulate emissions standards.

-2-

INTRODUCTION

This manual describes the installation and operation of the Ashley, APC4000 wood heater. This heater meets the

2015 U.S. Environmental Protection Agency's crib wood emission limits for wood heaters sold after May 15, 2015.

Under specic test conditions this heater has been shown to deliver heat at rates ranging from 6,569 to 34,785

Btu/hr.

Thank you for purchasing your pellet burning stove, you are now prepared to burn wood in the most efcient,

convenient way possible. To achieve the safest, most efcient and most enjoyable performance from your stove,

you must do three things: 1) Install it properly; 2) Operate it correctly; and 3) Maintain it regularly. The purpose of

this manual is to help you do all three.

PLEASE read this entire manual before installation and use of this pellet fuel-burning room heater. Failure to follow

these instructions could result in property damage, bodily injury or even death.

Keep this manual handy for future reference.

This stove has been independently tested to ASTM E1509-12 Standard Specication for Room Heaters, Pellet

Fuel Burning Type 1, ULC-S627 Standard for Solid Fuel Room Heaters, and Oregon Administrative Rules for Mobile

Homes (814-23-900 through 814-23-909) and Installation as a Stove Heater.

This pellet stove, when installed, must be electrically grounded in accordance with local codes, or in the absence

of local codes, with the National Electrical Code, ANSI/NFPA 70.

The authority having jurisdiction (such as municipal building department, re department, re prevention bureau,

etc.) should be consulted before installation to determine the need to obtain a permit.

This appliance is designed specically for use only with pelletized wood. It is designed for residential installation

according to current national and local building codes as a free-standing room heater. It is also approved as a

mobile home heater which is designed for connection to an outside combustion air source.

The stove will not operate using natural draft or without a power source for the blower systems and fuel feed

system and must not be burned with any type of coal (see PROPER FUEL).

This stove is designed to provide the optimum proportions of fuel and air to the re in order to burn free of smoke

and soot. Any blockage of the air supply to or from the stove will seriously degrade its performance and will be

evidenced by a smoking exhaust and a sooting window. For best operation the ash content of the pellet fuel

should be less than 1% and the caloric value approximately 8200 BTU/LB. Avoid high ash content fuels because

this will rapidly ll up the burn pot and eventually cut off the combustion air supply.

Commercial and industrial installations of this pellet stoves should not be used since operational control is often

not well managed in these settings.

-3-

• Do not operate your stove if you smell smoke

coming from it. Turn it off, monitor it, and call your

dealer.

• Never use gasoline, gasoline-type lantern fuel,

kerosene, charcoal lighter uid, or similar liquids

to start or “freshen up” a re in this stove. Keep all

such liquids well away from the stove while in use.

Never block free airow through the open vents of

the stove.

• Keep foreign objects out of the hopper.

• The stove will not operate during a power outage. If

an outage does occur, check the stove for smoke

spillage and open a window if any smoke spills into

the room.

• Disconnect the power cord before performing any

maintenance or repairs on the stove. NOTE: Turning

the stove “off” does not disconnect all power from

the stove.

•

• During the start up period; 1) DO NOT open the

viewing door; 2) DO NOT open the damper more

than ¼”; 3) DO NOT add pellets to the burnpot by

hand; 4) DO NOT use the Fuel Feed button (unless

you are priming the auger after running out of

pellets) as a dangerous condition could result.

• Do not unplug the stove if you suspect a

malfunction. Turn the stove off, periodically inspect

it, and call your dealer.

•

• Never try to repair or replace any part of the stove

unless instructions are given in this manual. All other

work should be done by a trained technician.

• Do not throw this manual away. This manual has

important operating and maintenance instructions

that you will need at a later time. Always follow the

instructions in this manual.

• Do not place clothing or other ammable items on

or near the stove.

• Do not operate the stove if the ame becomes

dark and sooty or if the burnpot overlls with pellets.

Turn the stove off, periodically inspect it, and call

your dealer.

• Hot while in operation. Keep children, clothing,

and furniture away. Contact may cause skin

burns. Educate all children of the danger of a

high temperature stove. Young children should be

supervised when they are in the same room as the

stove.

• If the stove is installed in a room without air

conditioning, or in an area where direct sunlight

can shine on the unit, it is possible this can cause

the temperature of the stove to rise to operational

levels; one of the sensors could then make the

stove start on its own. It is recommended that the

stove be unplugged when not in use for extended

amounts of time (i.e. during the summer months).

• The viewing door must be closed and latched

during operation.

• Contact your local building ofcials to obtain

a permit and information on any installation

restrictions or inspection requirements in your area.

Notify your insurance company of this stove as well.

• This unit must be properly installed to prevent the

possibility of a house re. The instructions must be

strictly adhered to. Do not use makeshift methods

or compromise in the installation.

• Your stove requires periodic maintenance and

cleaning. Failure to maintain your stove may lead

to smoke spillage in your home.

• This stove must be connected to a standard 120

V., 60 Hz grounded electrical outlet. Do not use an

adapter plug or sever the grounding plug. Do not

route the electrical cord underneath, in front of, or

over the stove.

• The exhaust system should be checked, at a

minimum, at least twice a year for any build up of

soot or creosote.

• This is a pressurized exhaust system. We suggest

sealing all vent connector joints with 500°F

(260°C) RTV silicone sealant to ensure consistent

performance and to avoid smoke spillage. We

also suggest that all horizontal connector joints be

sealed with UL-181-AP foil tape.

• Allow the stove to cool before carrying out any

maintenance or cleaning. Ashes must be disposed

in a metal container with a tight lid and placed on

a no combustible surface well away from the home

structure.

• This stove is designed and approved for pelletized

wood fuel only. Any other type of fuel burned in this

heater will void the warranty and safety listing.

• When installed in a mobile home, the stove must

be bolted to the oor, have outside air, and NOT BE

INSTALLED IN A BEDROOM (Per H.U.D. requirements).

Check with local building ofcials.

• This Company grants no warranty, implied or

stated, for the installation or maintenance of

your stove, and assumes no responsibility of any

consequential damage(s).

SAFETY PRECAUTIONS

Note: Register your product on line at www.usstove.com. See “Limited Warranty” section for specic warranty

information for your new purchase. Save your receipt with your records for any claims.

-4-

SPECIFICATIONS

Width: 25 ¼”

Height: 29 ½”

Depth: 24 ¼”

Weight: 340 lbs.

Flue size: 3” or 4”

Hopper Capacity: Up to 40 lbs.

(this can vary widely depending on pellet size, length,

and diameter)

EPA status: exempt

Burn time: 1 lb. to 4 ½ lbs. per hour

BTU range: 8,200 to 40,000

Approved installations: mobile home, alcove,

conventional

PREPARATION

Factory packaging must be removed, and some

minor assembly work is required prior to installation.

Access to the rear of the stove is necessary.

NOTE: Normally, your dealer will perform these

functions.

CLEARANCES

Your appliance has been tested and listed for

installation in residential, mobile home and alcove

applications.

FLOOR PROTECTION: Freestanding installations,

minimum

27 ¼” wide by 33 ¼” deep. The stove must be placed

on a continuous (grouted joints) noncombustible

material such as ceramic tile, cement board, brick,

3/8” millboard or equivalent, or other approved or

listed material suited for oor protection.

THE MATERIAL(S) USED MUST HAVE, OR COMBINE TO

HAVE, A MINIMUM INSULATIVE RATING OF ‘R1’.

NOTE: ceramic tile, or any tile, requires a continuous

sheet beneath to prevent the possibility of embers

falling through to the combustible oor if cracks or

separation should occur in the nished surface, this

would include oor protection for Built-in raised hearths.

Check local codes for approved alternatives.

Clearances are measured from the sides, back and

face (door opening) or stove body (refer to g. 3).

DO NOT USE MAKESHIFT MATERIALS OR COMPROMISES

IN THE INSTALLATION OF THIS UNIT.

INSTALL VENT WITH CLEARANCES SPECIFIED BY THE

VENT MANUFACTURER.

VISIBLE SMOKE

The amount of visible smoke being produced can be

n effective method of determining how efciently the

combustion process is taking place at the given settings.

Visible smoke consist of unburned fuel and moisture

leaving your stove. Learn to adjust the air settings of

your specic unit to produce the smallest amount of

visible smoke. Wood that has not been seasoned

properly and has a high wood moisture content will

produce excess visible smoke and burn poorly.

INSTALLATION

FIGURE 1

FIGURE 2

FIGURE 3

FLOOR PROTECTION

-5-

FIGURE 4

FIGURE 5

COMBUSTION AIR SUPPLY

For a mobile home installation the stove must be connected to an

outside source of combustion air. A 2” inside diameter metallic pipe,

either exible or rigid, may be attached to the inlet at the stove’s rear

(refer to gure 4). A rodent guard (minimum ¼” wire mesh)/wind hood

must be used at the terminus (refer to gure 5). All connections must be

secured and airtight by either using the appropriately sized hose clamp

and/or UL-181-AP foil tape.

For mobile home installations only: 2” inside diameter pipe may be used

for the rst 5 feet of combustion air supply run. From 5 to 10 feet use 2

¾” inside diameter pipe. No combustion air supply may exceed 10 feet.

SOURCES OF OUTSIDE COMBUSTION AIR

a. In replaces

• Chimney top.

• Ash clean out door.

b. For freestanding installations

• A hole in oor near stove rear terminating only in a ventilated

crawl space.

• A hole in the wall behind the stove.

WHEN OUTSIDE AIR IS NOT USED

If outside air is not used, it is important that combustion air is easily

available to the air inlet. A closeable outside air register can be used

in tightly insulated homes. In insert installations, ashing vents should not

be restricted. The ashing should not necessarily seal the replace face.

VENTING

Your appliance is certied for use with listed TYPE L-Vent, 3” or 4”

diameter in size. The stove was tested with Simpson Duravent brand.

Class “A” chimney is not required. Refer to the instructions provided by

the vent manufacturer, especially when passing through a wall, ceiling

or roof.

This is a pressurized exhaust system. We suggest sealing all vent

connector joints with 500°F (260°C) RTV silicone sealant to ensure

consistent performance and to avoid smoke spillage. We also suggest

that all horizontal connector joints be sealed with UL-181-AP foil tape.

It is strongly recommended that you have a minimum of 6’ of vertical

pipe in your exhaust system. For best performance of the stove limit the

number of elbows and horizontal pipe as much as possible

Follow l-vent chimney manufacturer’s installation instructions.

Do not connect this unit to a chimney ue serving another appliance.

Do not install a ue damper in the exhaust venting system of this unit.

Install vent at clearances specied by the vent manufacturer.

IMPORTANCE OF PROPER DRAFT

Draft is the force which moves air from the appliance up through the

chimney. The amount of draft in your chimney depends on the length of

the chimney, local geography, nearby obstructions and other factors.

Too much draft may cause excessive temperatures in the appliance.

Inadequate draft may cause backpufng into the room and ‘plugging’

of the chimney.

Inadequate draft will cause the appliance to leak smoke into the room

through appliance and chimney connector joints.

An uncontrollable burn or excessive temperature indicates excessive

draft. Take into account the chimney’s location to insure it is not too

close to neighbors or in a valley which may cause unhealthy or nuisance

conditions.

INSTALLATION

-6-

Equivalent Vent Length (EVL)

The longer the run of pipe in your installation (both with inserts and freestandings), the more restriction there is in

the system. Therefore, larger diameter pipe should be used.

• Use 4” pipe if you have more than 15 feet of equivalent vent length.

• Horizontal runs shall not exceed 10 feet of EVL.

• It is recommended that vertical runs be a minimum of 8 feet.

• To calculate EVL, use the following conversions:

90º elbow or “T” = 5 equivalent feet

45º elbow = 3 equivalent feet

Horizontal Pipe Run = 1 equivalent foot per actual foot

Vertical Pipe Run = 0.5 equivalent foot per actual foot

NOTE: At altitudes above 3,000 feet, we suggest the use of 4” diameter vent at an EVL of 7 feet or more.

INSTALLATION

A. HORIZONTALLY THROUGH WALL (refer to Figure 6)

NOTE: See “VENTING” and follow L-Vent chimney manufacturer’s instructions.

1. Position stove, adhering to clearances shown in Figures 1 & 2.

2. Locate position of hole in wall; directly behind stove exhaust vent (refer to gure 4).

3. Always maintain 3” clearance from combustible materials.

4. Install L-Vent wall thimble per L-Vent manufacturer’s instructions.

5. Attach enough piping to penetrate and extend at least 6” beyond exterior walls. An 8-foot vertical pipe

run is suggested where possible to reduce the possibility of smoke spill age in the event of a loss of negative

pressure.

6. Attach cap and seal outside wall thimbles with non-hardening waterproof mastic.

7. Termination should not be located so that hot exhaust gases can ignite trees, shrubs, or grasses or be a

hazard to children. Exhaust gases can reach temperatures of 500ºF and cause serious burns if touched.

Locate terminations: a) not less than 3 feet

above any forced air inlet located within 10 feet;

b) not less than 4 feet below or horizontally from,

or one foot above, any door, window or gravity

air inlet into any building; c) not less than two feet

from an adjacent building and not less than 7 feet

above grade when located adjacent to a public

walkway.

INSTALLATION

FIGURE 6

-7-

B. VERTICALLY WITH NEW CHIMNEY SYSTEM (Refer to

Figure 7)

NOTE: See “VENTING” and follow L-Vent chimney

manufacturer’s instructions.

OPTION: To achieve a center vertical installation a 45º

elbow and a clean-out tee can be used to offset the pipe

from the exhaust outlet to the rear center of the stove.

OPTION: Install L-Vent elbow in place of clean-out tee.

Locate stove. Drop plumb bob to center of tee outlet,

mark point on ceiling. Install ceiling support and L-Vent

pipe per L-Vent manufacturer’s instructions.

Always maintain 3” clearance from combustible

materials. When passing through additional oors or

ceilings, always install restop spacer.

After lining up for hole in roof, cut either around or

square hole in roof, always 3” larger all the way around

pipe. Install upper edge and sides of ashing under

roong materials, nail to the roof along upper edge. Do

not nail lower edge. Seal nail heads with non-hardening

waterproof mastic.

Apply non-hardening, waterproof mastic where the

storm collar will meet the vent and ashing. Slide storm

collar down until it sits on the ashing. Seal and install cap.

C. VERTICALLY INTO EXISTING CHIMNEY SYSTEM

Adapters are available to adapt from 3” L-Vent to 6” or

8” Class-A chimney. (Figure 8a)

As an alternative, 3” or 4” L-Vent can be run inside

existing chimney to termination. (Figure 8b)

This is the preferred method.

Follow guidelines for equivalent vent length.

INSTALLATION

FIGURE 7

FIGURE 8bFIGURE 8a

-8-

D. VERTICALLY INTO EXISTING MASONRY FIREPLACE

NOTE: See “VENTING” and follow L-Vent chimney

manufacturer’s instructions.

1. Have the masonry chimney inspected by a qualied

chimney sweep or installer to determine its structural

condition.

2. You will need a pipe length equal to the chimney

height from the hearth. If outside combustion air is

to be used, you will need a pipe length equal to the

chimney height plus 18 inches.

3. Install a blanking plate and the chimney pipe, and if

used the outside air pipe, as shown in Figure 9.

4. Attach the L-Vent adapter, a section of pipe and

clean out tee, making sure the clean out tee is

centered in the chimney ue area.

5. Position the stove, adhering to the clearances in

Figures 1 & 2.

6. Measure and build chimney top plate. Cut out holes

for chimney pipe, and if used the outside air pipe.

Install and seal with non-hardening mastic to prevent

water leakage. Install vent cap.

G. INSTALLATION THROUGH SIDE OF MASONRY CHIMNEY

NOTE: See “VENTING” and follow L-Vent chimney

manufacturer’s instructions.

1. Position the stove, adhering to the clearances in

Figures 1 & 2. Mark the center of the hole where the

pipe is to pierce the masonry chimney.

2. It will be necessary to break out the masonry around

the location of the pipe center mark. Use a 4-inch

diameter hole for 3-inch pipe and 5-inch diameter

hole for 4-inch pipe.

3. Measure and build chimney top plate. Cut out holes

for chimney pipe, and if used the outside air pipe.

4. Install the tee on the bottom of the vertical pipe

system and lower it down the chimney until the center

branch of the tee is level with the center of the hole in

the masonry, as shown in Figure 10.

5. Install and seal the top plate from step 3 with non-

hardening mastic. Slip the storm collar over the pipe,

and while holding the pipe at the proper elevation,

afx the collar with a minimum of three ¼” stainless

steel sheet metal screws. Seal all joints and seams

around the collar.

6. Connect the horizontal pipe by pushing it through the

hole in the masonry and lining it up with the branch in

the tee. Push the pipe into the tee while twisting it to

lock it into the tee.

7. If desired, once the horizontal pipe is in place, the

space between the pipe and masonry may be lled

with high-temperature grout.

8. Install the trim collar. An adjustable pipe length and

adapter may be needed to nish the connection to

the stove.

INSTALLATION

FIGURE 9

FIGURE 10

-9-

ELECTRICAL INSTALLATION

This stove is provided with a 6-foot grounded electrical cord extending from the rear of the stove.

We recommend connecting to a good quality surge protector that is plugged into a standard three-prong,

120V, 60 Hz electrical outlet.

Do NOT connect the unit to a GFCI socket.

Voltage variations can lead to serious performance problems. The stoves electrical system is designed for 120V

AC with no more than 5% variation. This company cannot accept responsibility for poor performance or damage

due to inadequate voltage. If connected to an older, two-prong outlet, a separate ground wire should be run to

a proper ground (refer this to a qualied technician). Always route the electrical cord so that it will not come in

contact with any hot part of the stove.

SPECIAL MOBIL HOME REQUIREMENTS

WARNING: DO NOT INSTALL IN A SLEEPING ROOM.

NOTE: Installation should be in accordance with the Manufactured Home and Safety Standard (HUD), CFR 3280,

Part 24

For installation in a mobile home, an outside source of combustion air must be used

(See “COMBUSTION AIR SUPPLY”).

The appliance must be grounded to the steel chassis of the home with 8 Ga. copper wire using a serrated or star

washer to penetrate paint or protective coating to ensure grounding.

The appliance must be securely fastened to the oor of the mobile home through the two holes in the rear of

the stove using 2, ¼” lag bolts that are long enough to go through both a hearth pad, if used, and the oor of the

home. (See gure 11) Refer to “VENTING” for proper exhaust congurations

CAUTION:

THE STRUCTURAL INTEGRITY OF THE MOBILE HOME

FLOOR, WALL AND CEILING/ROOF MUST BE

MAINTAINED.

INSTALLATION

BOLT HOLES

FIGURE 11

-10-

PANEL CONTROLS (SEE FIGURE 12)

The blowers and automatic fuel supply are controlled from a panel on the left-

hand side of the furnace. The control panel functions are as follows.

a. ON/OFF SWITCH

• When pushed the stove will automatically ignite. No other restarter is

necessary. The igniter will stay on for at least 10 and up to 15 minutes,

depending on when Proof of Fire is reached. The re should start in

about 5 minutes.

• The green light located above the On/Off button (in the On/Off box)

will ash during the ignition start-up period. (See gure 12)

• The Feed Rate Advance is inoperable during the ignition start period.

When the red light continuously stays on the Feed Rate Advance can

be adjusted to achieve the desired heat output.

NOTE: If the stove has been shut off, and you want to re-start it while it is still

warm, the “on/off” button must be held down for 2 seconds.

b. FUEL FEED SWITCH

• When the “Fuel Feed” button is pushed and held down the stove will

feed pellets continuously into the burnpot.

• While the stove’s auger system is feeding pellets the amber light (in the

“Fuel Feed” box) will be on. (See gure 12)

CAUTION: DO NOT USE THIS CONTROL DURING NORMAL OPERATION BECAUSE

IT COULD SMOTHER THE FIRE AND LEAD TO A DANGEROUS SITUATION.

c. HIGH FAN SWITCH

• The room air fan speed varies directly with the feed rate. The “HIGH

FAN” switch overrides this variable speed function. It will set the room

air blower speed to high at any feed rate setting.

• When the “HIGH FAN” button is pushed the room air fan will switch to

its highest setting.

• When this button is pushed again the room air fan will return to its

original setting based on the Feed Rate Advance setting.

d. RESET TRIM

Different size and quality pellet fuel may require adjustment of the “1” feed

setting on the Feed Rate Advance bar graph. This is usually a one-time adjustment based on the fuel you are

using. The “RESET TRIM” button when adjusted will allow for 3 different feed rate settings for the #1 feed setting

only. To adjust simply push the “RESET TRIM” button while the stove is operating at setting “1” and watch the bar

graph.

• When the “1” and “3” lights are illuminated on the bar graph the low feed rate is at its “lowest” setting.

(approx. 0.9 pounds per hour)

• When the “1” light is illuminated on the bar graph the low feed rate is at its “normal” setting.

• When the “1” & “4” lights are illuminated on the bar graph the low feed rate is at its “highest” setting.

NOTE: When the stove is set on “1” the “reset trim” values will be shown on the Feed Rate Advance bar graph.

For example if the Reset Trim is set to its lowest setting every time the stove is set to low the “1” and “3” lights will

be illuminated on the bar graph.

e. HEAT LEVEL ADVANCE

• This button when pushed will set the pellet feed rate, hence the heat output of your stove. The levels of heat

output will incrementally change on the bar graph starting from level “1” to “4”.

NOTE: When dropping more than 2 heat level settings (i.e. 4 to 1) push the ‘High Fan’ button and allow the room

air fan to run at that setting for at least 5 minutes to prevent the stove from tripping the high temp thermodisk. If

the high temp thermodisk does trip see “SAFETY FEATURES”.

CAUTION: THE “4” SETTING IS DESIGNED FOR TEMPORARY USE ONLY. IF USED FOR EXTENDED PERIODS, IT CAN

SHORTEN THE LIFE EXPECTANCY OF THE UNITS COMPONENTS. AVOID USE AT THIS SETTING FOR MORE THAN ONE

HOUR AT A TIME.

OPERATION

www.ASHLEYHEARTHPRODUTS.com

FIGURE 12

-11-

PROPER FUEL

This heater is designed to burn only PFI Premium grade pellets. This appliance can also burn pellets rated as

standard after May 16, 2015

DO NOT BURN:

1. Garbage;

2. Lawn clippings or yard waste;

3. Materials containing rubber, including tires;

4. Materials containing plastic;

5. Waste petroleum products, paints or paint thinners,

or asphalt products;

6. Materials containing asbestos;

7. Construction or demolition debris;

8. Railroad ties or pressure-treated wood;

9. Manure or animal remains;

10. Salt water driftwood or other previously salt water

saturated materials;

11. Unseasoned wood; or

12. Paper products, cardboard, plywood, or

particleboard. The prohibition against burning

these materials does not prohibit the use of re

starters made from paper, cardboard, saw dust,

wax and similar substances for the purpose of

starting a re in an affected wood heater.

Burning these materials may result in release of toxic fumes or render the heater ineffective and cause smoke.

THIS STOVE IS APPROVED FOR BURNING PELLETIZED WOOD FUEL ONLY! Factory-approved pellets are those ¼”

or 5/16” in diameter and not over 1” long. Longer or thicker pellets sometimes bridge the auger ights, which

prevents proper pellet feed. Burning wood in forms other than pellets is not permitted. It will violate the building

codes for which the stove has been approved and will void all warranties. The design incorporates automatic

feed of the pellet fuel into the re at a carefully prescribed rate. Any additional fuel introduced by hand will not

increase heat output but may seriously impair the stoves performance by generating considerable smoke. Do

not burn wet pellets. The stove’s performance depends heavily on the quality of your pellet fuel. Avoid pellet

brands that display these characteristics:

a. Excess Fines – “Fines” is a term describing crushed pellets or loose material that looks like sawdust or sand.

Pellets can be screened before being placed in hopper to remove most nes.

b. Binders – Some pellets are produced with materials to hold them together, or “bind” them.

c. High ash content – Poor quality pellets will often create smoke and dirty glass. They will create a need for

more frequent maintenance. You will have to empty the burnpot plus vacuum the entire system more often.

Poor quality pellets could damage the auger. This company cannot accept responsibility for damage due

to poor quality pellets. Your dealer can recommend a good quality pellet dealer in your area.

PRE-START-UP CHECK

Remove burnpot, making sure it is clean and none of the air holes are plugged. Clean the rebox, and then

reinstall burnpot. Clean door glass if necessary (a dry cloth or paper towel is usually sufcient). Never use abrasive

cleaners on the glass or door. Check fuel in the hopper, and rell if necessary.

NOTE: The hopper can hold up to 40 lbs. of pellets.

BUILDING A FIRE

Never use a grate or other means of supporting the fuel. Use only the approved burnpot.

During the start up period:

1. DO NOT open the viewing door.

2. DO NOT open the damper more than ¼”.

3. DO NOT add pellets to the burnpot by hand.

4. DO NOT use the Fuel Feed button (unless you are priming the auger after running out of pellets).

A dangerous condition could result.

NOTE: During the rst few res, your stove will emit an odor as the high temperature paint cures or becomes

seasoned to the metal. Maintaining smaller res will minimize this. Avoid placing items on stovetop during this

period because paint could be affected.

OPERATION

-12-

OPERATION

THE HOTROD AUTOMATIC FIRESTARTER

a. Fill hopper and clean burnpot.

b. Press “Power” button. Make sure light is on.

c. The damper should be completely closed or open no more than ¼” during start-up. This will vary depending

on your installation and elevation. Once re is established adjust for desired ame increasing the amount the

damper is open as the heat setting is increased. (See “DAMPER CONTROL”)

d. Adjust feed rate to desired setting by pressing “Feed Rate Advance” button.

If re doesn’t start in 15 minutes, press “Power”, wait a few minutes and start procedure again.

DAMPER CONTROL

The damper control rod on the stove’s lower left side adjusts the combustion air. This control is necessary due to

the varied burn characteristics of individual installations, different pellet brands and pellet feed rates. It allows you

to improve the efciency of your stove. Providing correct combustion air will reduce the frequency of cleaning

your glass door and prevent the rapid buildup of creosote inside your stove and chimney.

You should adjust the damper based on the re’s appearance. A low, reddish, dirty re can be improved by

pulling the damper out slightly. A “blow torch” re can be improved by pushing the damper in a bit.

As a general rule, on lower feed rate settings, the damper should be in farther. On higher feed rates, the damper

should be more open. Through trial and error, you will nd the best setting. Consult your dealer if you need help.

NOTE: On “1”, damper should be either completely closed or out approximately ⅛” to ¼”. If damper is out too

far, it can cause the re to go out.

OPENING DOOR

If the door is opened while the stove is in operation it must be closed within 30 seconds or the stove will shut

down. If the stove shuts down push the “Power” button to continue the operation of your stove.

ROOM AIR FAN

When starting your stove the Room Air Fan will not come on until the stove’s heat exchanger warms up. This

usually takes about 10 minutes from start-up.

-13-

RE-STARTING A WARM STOVE

If the stove has been shut off, and you want to re-start it while it is still warm, the “on/off” button must be held

down for 2 seconds.

IF STOVE RUNS OUT OF PELLETS

The re goes out and the auger motor and blowers will run until the stove cools. This will take 30 to 45 minutes.

After the stove components stop running the “Power” and the BAR GRAPH lights stay on for 10 minutes.

After the 10 minutes the “3” light on the bar graph will ash and the “Power” light will go off.

To restart, rell hopper, press “Power” button, and then press “Fuel Feed” button until pellets begin to fall into

burnpot.

REFUELING

We recommend that you not let the hopper drop below ¼ full.

KEEP HOPPER LID CLOSED AT ALL TIMES EXCEPT WHEN REFILLING. DO NOT OVERFILL HOPPER.

MAINTENANCE TOOL

A tool has been provided to help with the following functions:

Stirring pellets in hopper – unlike liquids in a tank, pellets do not drain evenly into the auger. Bridging across the

opening can occur. Pellets can hang up on the sides of the hopper. Occasionally “stirring” the hopper can help.

NOTE: To help prevent bridging of pellets, common wax paper can be rubbed on the sidewalls and bottom of

the hopper.

Cleaning heat exchanger tubes – see instructions in “CLEANING”.

Scrape ashes from burnpot.

SHUTDOWN PROCEDURE

Turning your stove off is a matter of pressing the “Power” control panel switch. The red light will go out. The

blowers will continue to operate until internal rebox temperatures have fallen to a preset level.

SAFETY FEATURES

Your stove is equipped with a high temperature thermodisc. This safety switch has two functions.

To recognize an overheat situation in the stove and shut down the fuel feed or auger system.

In case of a malfunctioning convection blower, the high-temperature thermodisc will automatically shut down

the auger, pre venting the stove from overheating.

NOTE: The thermodisc will reset itself once the stove has cooled. The manufacturer recommends that you call

your dealer if this occurs as this may indicate a more serious problem. A service call may be required.

If the combustion blower fails, an air pressure switch will automatically shut down the auger.

NOTE: Opening the stove door for more than 30 seconds during operation will cause enough pressure change to

activate the air switch, shutting the fuel feed off. Close the door and press “On/Off” button to continue operation

of your stove.

OPERATION

FIGURE 13

-14-

PLEASE READ THIS!

OPERATING SAFETY PRECAUTIONS

a. Hot while in operation. Keep children, clothing, and furniture away. Contact may cause skin burns.

b. If you notice a smoldering re (burnpot full but no visible ame) AND a heavy smoke buildup in rebox, im

mediately TURN OFF the stove, but DO NOT unplug it. Do not open the door, change the damper setting or

tamper with any controls on the stove. Wait until rebox clears, and blowers shut down, do as instructed in

“PRE-START-UP CHECK” and “BUILDING A FIRE”, then attempt to restart the re. If the problem persists contact

your dealer.

c. WARNING: DO NOT ADD PELLETS TO THE BURNPOT BY HAND AT ANY TIME, A DANGEROUS CONDITION COULD

RESULT.

d. WARNING: DURING THE START UP CYCLE; 1) DO NOT OPEN THE VIEWING DOOR; 2) DO NOT OPEN THE DAMPER

MORE THAN ¼”; 3) DO NOT USE THE FUEL FEED BUTTON (UNLESS PRIMING THE AUGER AFTER RUNNING OUT OF

PELLETS). A DANGEROUS CONDITION COULD RESULT.

e. Pellets should be stored in a dry place. The pellets should not be stored within 12” of the stove.

f. DO NOT STORE OR USE FLAMMABLE LIQUIDS, ESPECIALLY GASOLINE, IN THE VICINITY OF YOUR STOVE. NEVER

USE A GAS OR PROPANE TORCH, GASOLINE, GASOLINE-TYPE LANTERN FUEL, KEROSENE, CHARCOAL LIGHTER

FLUID OR SIMILAR FLUIDS TO START OR “FRESHEN UP” A FIRE IN THIS HEATER.

g. WARNING: DO NOT OVERFIRE THIS STOVE. This may cause serious damage to your stove and void your

warranty. It also may create a re hazard in your home. IF ANY EXTERNAL PART OF THE UNIT BEGINS TO GLOW,

YOU ARE OVERFIRING. Immediately press the “POWER” switch on the control panel.

h. KEEP ALL LOOSE OR MOVEABLE HOUSEHOLD COMBUSTIBLES, SUCH AS FURNITURE, DRAPES, TOYS, ETC. AT

LEAST THREE FEET FROM THE OPERATING STOVE.

i. Maintain proper ventilation. It is important that adequate oxygen be supplied to the re for the combustion

process. Modern houses are often so well insulated that it may become necessary to open a window slightly

or install an outside air vent to provide sufcient combustion air.

j. Since heating with a solid fuel is potentially hazardous, even with a well made and thoroughly tested stove,

it would be wise to install strategically placed smoke detectors and have a re extinguisher in a convenient

location, near an exit.

k. Do not open stove door when operating unless necessary. This will create a dirty, inefcient burn and could

allow smoke spillage or sparks to escape.

l. Do not permit operation by young children or those unfamiliar with stove’s operation.

m. Do not service or clean this appliance without disconnecting the power cord.

n. Do not abuse the door glass by striking, slamming or similar trauma. Do not operate the stove with the glass

removed, cracked or broken.

o. If the stove is installed in a room without air conditioning, or in an area where direct sunlight can shine on the

unit, it is possible this can cause the temperature of the stove to rise to operational levels; one of the sensors

could then make the stove start on its own. It is recommended that the stove be unplugged when not in use

for extended amounts of time (i.e. during the summer months).

p. This wood heater has a manufacturer-set minimum low burn rate that must not be altered. It is against

federal regulations to alter this setting or otherwise operate this wood heater in a manner inconsistent with

operating instructions in this manual.

q. Attempts to achieve heat output rates that exceed heater design specications can result in permanent

damage to the heater.

OPERATION

-15-

OPTIONAL THERMOSTAT

A thermostat may help you maintain a constant house

temperature automatically. A millivolt thermostat is required.

A xed wall mount or a hand held model can be used. The

control panel can be set up two ways to operate your stove

in thermostat mode.

NOTE: YOUR THERMOSTAT SHOULD BE INSTALLED BY AN

AUTHORIZED DEALER OR SERVICE PERSON.

THERMOSTAT INSTALLATION

• A MILLIVOLT THERMOSTAT IS REQUIRED.

• Unplug stove from power outlet.

• Remove control board from stove.

• The two thermostat wires connect to the terminal block

on the lower left side of the back of the control board.

(See gure 14)

• Insert the wires in the terminal side and tighten the two

screws.

MODES

TO SWITCH BETWEEN ANY OF THE THREE MODES THE STOVE

MUST BE SHUT OFF, THE NEW MODE SELECTED, AND THE STOVE

RESTARTED.

MANUAL MODE

• USE THIS MODE EXCLUSIVELY IF YOU DO NOT CONNECT

AN OPTIONAL THERMOSTAT

• In this mode the stove will operate only from the control

panel as detailed in the “OPERATION” section of this

owner’s manual.

HIGH/LOW THERMOSTAT MODE

• USE THIS MODE ONLY IF YOU CONNECT A THERMOSTAT

• When engaged in this mode the stove will automatically

switch between two settings. When warm enough, it will

switch to the #1 or low setting. The room air blower will

also slow to its lowest speed.

• The Heat Level Advance setting on the bar graph will

stay where it was initially set. When the house cools

below the thermostat setting, the stove will switch to the

feed rate of the heat level advance setting.

ON/OFF THERMOSTAT MODE

• USE THIS MODE ONLY IF YOU CONNECT A THERMOSTAT

• In this mode when the home is warm enough the stove

will shut off. The fans will continue to run until the

stove cools.

• When the home cools below the thermostat setting, the

stove will auto matically restart and run at the last feed

rate setting.

NOTE: When in “high/low” or “on/off” thermostat mode –

• Do not operate the stove higher than the #3 setting.

• Set damper control rod approximately ¼” to ½” out.

This will vary depending on elevation and weather

conditions. Observe stoves operation and adjust damper

as necessary.

THERMOSTAT INSTALLATION

On/Off High/Low

Manual

FIGURE 14

-16-

FAILURE TO CLEAN AND MAINTAIN THIS UNIT AS INDICATED CAN RESULT

IN POOR PERFORMANCE AND SAFETY HAZARDS. NEVER CLEAN WHEN

HOT. NOTE: Inspect burn pot periodically to see that holes have not

become plugged, if so, clean thoroughly.

ASH REMOVAL

Ashes should be placed in a metal container with a tight-tting lid.

The closed container or ashes should be placed on a non-combustible

surface or on the ground, well away from all combustible materials

pending nal disposal. If ashes are disposed of by soil burial or otherwise

locally dispersed, they should be retained in the closed container until

all cinders have thoroughly cooled.

ASH DISPOSAL

This furnace has an ash bin located below the rebox. To remove ashes:

a. Make sure re is out and rebox is cool.

b. With the door closed clean heat exchanger tubes. (See “CLEANING”

and Figure 15).

c. Open door and remove the optional imitation log set, if in use.

Remove the burnpot’s inner section by grasping it and pulling

straight up (see Figure 16).

d. Empty ashes from inner section into the ash bin through the opening

in the bottom of the rebox. Scrape inner section with cleaning

tool. Make sure holes are not plugged.

e. Scrape ash in rebox into the ash bin through the opening in the

bottom of the rebox or vacuum to remove ashes (see Figure 17).

WARNING: Make sure ashes are cool to the touch before using a

vacuum. See “VACUUM USE”.

f. Periodically remove and empty ash bin (see Figure 18) by

unscrewing the two knobs on the front of it and pulling it straight

out. Dispose of ashes properly. (See “ASH REMOVAL” above)

g. Replace ash bin, making sure to tighten the knobs and maintaining

a good seal.

h. Replace inner section into burnpot; make sure it is level and pushed

all the way back down and that the igniter hole is to the rear when

it is rein stalled (see Figure 16).

i. Make the burnpot is level and pushed all the way back in when it

is rein stalled. If the collar on the burnpot attached to the fresh air

tube is not pushed back to meet the rebox wall, the Hot Rod will

not work properly.

SMOKE AND CO MONITORS

Burning wood naturally produces smoke and carbon monoxide(CO)

emissions. CO is a poisonous gas when exposed to elevated

concentrations for extended periods of time. While the modern

combustion systems in heaters drastically reduce the amount of CO

emitted out the chimney, exposure to the gases in closed or conned

areas can be dangerous. Make sure you stove gaskets and chimney

joints are in good working order and sealing properly to ensure

unintended exposure. It is recommended that you use both smoke and

CO monitors in areas having the potential to generate CO.

VACUUM USE

If a vacuum is used to clean your unit, we suggest using a vacuum

designed for ashes. (We recommend LoveLess Ash Vac, 1-800-568-3949

Ext. #27) Some regular vacuums and shop vacs leak ash into the room.

Your vacuum or shop vac may have a special lter or bag available to

eliminate this leakage.

MAINTENANCE

FIGURE 15

Igniter Hole

FIGURE 17

FIGURE 16

FIGURE 18

-17-

CLEANING

a. Heat Exchange Tubes – Your stove is designed with a

built-in heat exchange tube cleaner. This should be used

every two or three days to remove accumulated ash on

the tubes, which reduces heat transfer on this furnace.

Insert the handle end (with hole) of the cleaning tool

onto the cleaning rod (refer to gure 15). The cleaner

rod is located in the grill above the stove door. Move the

cleaner rod back and forth several times to clean the

heat exchanger tubes. Be sure to leave tube cleaner at

the rear of the stove.

b. Interior Chambers – Four ash doors and two upper bafes

in the rebox in your model can be removed for periodic

cleaning (Figure 19). These doors allow access to the

chamber surrounding the rebox.

NOTE: When removing the upper bafes do not remove the

screws; just loosen them enough to allow the bafes to be

removed.

Periodically, you must vacuum ashes from this chamber. In

some cases you will need to remove creosote, which can

accumulate rapidly under certain conditions. A small wire

brush can be used. It is important to remove this creosote

because it is highly combustible. INSPECT BEHIND THESE

CLEANING PLATES AT LEAST ONCE PER TON OF PELLETS BURNED

UNTIL YOU ARE FAMILIAR WITH HOW ASHES AND CREOSOTE

ACCUMULATE WITH YOUR OPERATING PRACTICES. Use the

small wire brush to also clean the inside of the chamber walls,

above the access doors.

BLOWERS

DANGER: RISK OF ELECTRIC SHOCK. DISCONNECT POWER

BEFORE SERVICING UNIT.

Cleaning – Over a period of time, ashes or dust may collect

on the blades of both the combustion blower and convection

blower. Periodically the blowers should be vacuumed clean

as these ashes can impede performance. Creosote can

also accumulate in the combustion blower. This needs to

be brushed clean. The convection blower is accessed by

removing the stove’s left side panel. The combustion blower

can be accessed by removing the stove’s right side panel.

The convection blower is on the left (facing stove), and the

combustion blower is on the right.

NOTE: When cleaning, be careful not to dislodge balancing

clip on convection blower or to bend fan blades. Some stove

owners lightly spray an anti-creosote chemical on the re to

help reduce creosote formation within the stove.

Baffle Plates

Ash Doors

Air Switch Tube

MAINTENANCE

Auger Shaft

Combustion Blower

POF Thermodisc

Air Switch

Combustion Blower

Auger Motor

Convection

Blower

High Temp

Thermodisc

FIGURE 19

FIGURE 20

FIGURE 21

-18-

CHIMNEY CLEANING

a. Creosote Formation – When any wood is burned slowly, it produces tar and other organic vapors, which

combine with expelled moisture to form creosote. The creosote vapors condense in the relatively cool

chimney ue or a newly started re or from a slow-burning re. As a result, creosote residue accumulates on

the ue lining. When ignited, this creosote makes an extremely hot re, which may damage the chimney or

even destroy the house. Despite their high efciency, pellet stoves can accumulate creosote under certain

conditions.

b. Soot and Fly Ash: Formation and Need for Removal - The products of combustion will contain small particles of

y ash. The y ash will collect in the exhaust venting system and restrict the ow of the ue gases. Incomplete

combustion, such as occurs during startup, shutdown, or incorrect operation of the room heater will lead to

some soot formation which will collect in the exhaust venting system. The exhaust venting system should be

inspected at least once every year or ton of pellets burned to determine if cleaning is necessary.

c. Inspection and Removal – The chimney connector and chimney should be inspected annually or per ton to

determine if a creosote or y ash build-up has occurred. If creosote has accumulated, it should be removed

to reduce the risk of a chimney re. Inspect the system at the stove connection and at the chimney top.

Cooler surfaces tend to build creosote deposits quicker, so it is important to check the chimney from the top

as well as from the bottom.

The creosote should be removed with a brush specically designed for the type of chimney in use. A qualied

chimney sweep can perform this service. It is also recommended that before each heating season the entire

system be professionally inspected, cleaned and, if necessary, repaired.

To clean the chimney, detach the vent at the combustion blower transition where it is attached to the blower.

RECOMMENDED MAINTENANCE SCHEDULE

Use this as a guide under average-use conditions. Gasket around door and door glass should be inspected and

repaired or replaced when necessary. (See “REPLACEMENT PARTS”)

REMOVAL AND REPLACEMENT OF BROKEN DOOR GLASS

While wearing leather gloves (or any other gloves suitable for handling broken glass), carefully remove any loose

pieces of glass from the doorframe. Dispose of all broken glass properly. Return the damaged door to your dealer

for repair or replacement. This unit’s door uses a 5/8” diameter rope gasket.

Neither the appliance owner nor any other unauthorized person(s) should replace the door glass. An authorized

dealer must perform all repairs involving door glass.

Daily Weekly Annually or per Ton

Burn Pot Stirred Emptied

Glass Wiped Cleaned

Combustion Chamber Brushed

Ashes Emptid

Interior Chambers Vacuumed

Heat Exchange Tubes Two passes

Combustion Blower Blades Vacuumed/Brushed

Convection Blower Impeller Vacuumed/Brushed

Vent System Cleaned

Gaskets Inspected

Hopper (end of season)

Emptied and

Vacuumed

MAINTENANCE

-19-

When your stove acts out of the ordinary, the rst reaction is to call for help. This guide may save time and money

by enabling you to solve simple problems yourself. Problems encountered are often the result of only ve factors:

1) poor fuel; 2) poor operation or maintenance; 3) poor installation; 4) component failure; 5) factory defect. You

can usually solve those problems related to 1 and 2. Your dealer can solve problems relating to 3, 4 and 5. Refer

to diagrams on page 17 to help locate indicated parts.

For the sake of troubleshooting and using this guide to assist you, you should look at your heat level setting to

see which light is ashing.

** CAUTION – UNPLUG THE STOVE FROM ALL POWER PRIOR TO ATTEMPTING TO SERVICE THE UNIT! **

STOVE SHUTS OFF AND THE # 2 LIGHT FLASHES

Possible Causes: Possible Remedies: (Unplug stove rst when possible)

1. Airow switch hose or stove attachment pipes for hose

are blocked.

Unhook air hose from the air switch and blow through it. If

air ows freely, the hose and tube are ne. If air will not

ow throw the hose, use a wire coat hanger to clear the

blockage.

2. The air inlet, burnpot, interior combustion air chambers,

combustion blower, or exhaust pipe are blocked with

ash or foreign material.

Follow all cleaning procedures in the maintenance section

of the owner’s manual.

3. The rebox is not properly sealed.

Make sure the door is closed and that the gasket is in good

shape. If the ash door has a latch, make sure the ash door

is properly latched and the gasket is sealing good. If the

stove has just a small hole for the ashes to fall through under

the burnpot, make sure the slider plate is in place to seal off

the rebox oor.

4. Vent pipe is incorrectly installed.

Check to make sure vent pipe installation meets criteria in

owner’s manual.

5. The airow switch wire connections are bad.

Check the connectors that attach the gray wires to the air

switch.

6. The gray wires are pulled loose at the Molex connector

on the wiring harness

Check to see if the gray wires are loose at the Molex

connector.

7. Combustion blower failure.

With the stove on, check to see if the combustion blower is

running. If it is not, you will need to check for power going

to the combustion blower. It should be a full current. If

there is power, the blower is bad. If there is not, see #8.

8. Control board not sending power to combustion

blower.

If there is no current going to the combustion blower, check

all wire connections. If all wires are properly connected,

you have a bad control board.

9. Control board not sending power to air switch.

There should be a 5-volt current (approximately) going to

the air switch after the stove has been on for 30 seconds.

10. Air switch has failed (very rare).

To test the air switch, you will need to disconnect the air

hose from the body of the stove. With the other end still

attached to the air switch, very gently suck on the loose

end of the hose (you may want to remove the hose entirely

off the stove and the air switch rst and make sure it is

clear). If you hear a click, the air switch is working. BE

CAREFUL, TOO MUCH VACUUM CAN DAMAGE THE AIR

SWITCH.

TROUBLESHOOTING GUIDE

-20-

STOVE SHUTS OFF AND THE #3 LIGHT FLASHES

Possible Causes: Possible Remedies: (Unplug stove rst when possible)

1. The hopper is out of pellets. Rell the hopper.

2. The air damper is too far open for a low feed setting.

If burning on the low setting, you may need to close the

damper all the way (push the knob in so it touches the side

of the stove).

3. The burnpot is not pushed completely to the rear of the

rebox.

Make sure that the air intake collar on the burnpot is

touching the rear wall of the rebox.

4. The burnpot holes are blocked. Remove the burnpot and thoroughly clean it.

5. The air inlet, the interior chambers, or exhaust system

has a partial blockage.

Follow all cleaning procedures in the maintenance section

of the owner’s manual.

6. The hopper safety switch has failed or hopper is open.

When operating the unit, be sure the hopper lid is closed so

that the hopper safety switch will activate. Check the wires

leading from the hopper safety switch to the control panel

and auger motor for secure connections. Use a continuity

tester to test the hopper safety switch; replace if necessary.

7. The auger shaft is jammed.

Start by emptying the hopper. Then remove the auger

motor by removing the auger pin. Remove the auger shaft

inspection plate in the hopper so that you can see the

auger shaft. Gently lift the auger shaft straight up so that

the end of the auger shaft comes up out of the bottom

auger bushing. Next, remove the two nuts that hold the

top auger biscuit in. Then rotate the bottom end of the

auger shaft up towards you until you can lift the shaft out

of the stove. After you have removed the shaft, inspect it

for bent ights, burrs, or broken welds. Remove any foreign

material that might have caused the jam. Also, check the

auger tube for signs of damage such as burrs, rough spots,

or grooves cut into the metal that could have caused a

jam

8. The auger motor has failed.

Remove the auger motor from the auger shaft and try to

run the unit. If the motor will turn the shaft is jammed on

something. If the motor will not turn, the motor is bad.

9. The Proof of Fire (POF) thermodisk has malfunctioned.

Temporarily bypass the POF thermodisk by disconnecting

the two brown wires and connecting them with a short

piece of wire. Then plug the stove back in. If the stove

comes on and works, you need to replace the POF

thermodisk. This is for testing only. DO NOT LEAVE THE

THERMODISC BYPASSED. Your blowers will never shut off

and if the re went out the auger will continue to feed

pellets until the hopper is empty if you leave the POF

thermodisk bypassed.

10. The high limit thermodisk has tripped or is defective.

Wait for the stove to cool for about 30 - 45 minutes. It should

now function normally. If not use the owner’s manual to

locate the high limit thermodisk. To test if the thermodisk is

bad, you can bypass it as described previously for the POF

thermodisk.

11. The fuse on the control board has blown.

Remove the control board. On the back there is one fuse.

If it appears to be bad, replace it with a 5 Amp 125 Volt

fuse. Plug the stove back in and try to run the unit.

12. The control board is not sending power to the POF

thermodisk or other auger system components.

There should be a 5-volt (approximately) current going

to the POF thermodisk after the stove has been on for 10

minutes.

TROUBLESHOOTING GUIDE

La page charge ...

Ashley Hearth Products APC4000B Manuel utilisateur

Marque: Ashley Hearth Products

Modèle: APC4000B

Catégorie: Cheminées

Taper: Manuel utilisateur

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Ashley Hearth Products APC4000B User manual

Ashley Hearth Products APC4000B Manuel utilisateur

Ce manuel convient également à

Ashley Hearth Products APC4000B Manuel utilisateur

dans d''autres langues

Autres documents