DeWalt DCT418 Manuel utilisateur

DCT418

12V Max* Hand-Held Radar Scanner

Scanner-radar portable de 12V max*

Escáner radar portátil de 12V Max*

INSTRUCTION MANUAL

GUIDE D'UTILISATION

MANUAL DE INSTRUCCIONES

INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA DE

GARANTÍA. ADVERTENCIA: LÉASE ESTE INSTRUCTIVO ANTES DE

USAR EL PRODUCTO.

If you have questions or comments, contact us.

Pour toute question ou tout commentaire, nous contacter.

Si tiene dudas o comentarios, contáctenos.

1-800-4-DEWALT • www.dewalt.com

1

English

SAVE ALL WARNINGS AND INSTRUCTIONS

FOR FUTURE REFERENCE

Work Area Safety

a) Keep work area clean and well lit. Cluttered or dark areas

invite accidents.

b) Keep children and bystanders away while operating a

hand-held radar scanner. Distractions can cause you to lose

control.

Personal Safety

a) Stay alert, watch what you are doing and use common

sense when operating a hand-held radar scanner. Do

not use a hand-held radar scanner while you are tired

or under the influence of drugs, alcohol or medication.

A moment of inattention while operating the hand-held radar

scanner may result in serious personal injury.

b) Do not overreach. Keep proper footing and balance at

all times. This enables better control of the hand-held radar

scanner in unexpected situations.

c) Dress properly. Do not wear loose clothing or jewelry.

Keep your hair, clothing and gloves away from moving

parts. Loose clothes, jewelry or long hair can be caught in

moving parts.

Use and Care

a) Store an idle hand-held radar scanner out of the reach

of children and do not allow persons unfamiliar with the

hand-held radar scanner or these instructions to operate

the hand-held radar scanner. Hand-held radar scanners are

dangerous in the hands of untrained users.

b) Use the hand-held radar scanner, accessories and tool

bits, etc. in accordance with these instructions, taking

into account the working conditions and the work to be

Deﬁ nitions: Safety Guidelines

The definitions below describe the level of severity for each

signal word. Please read the manual and pay attention to these

symbols.

DANGER: Indicates an imminently hazardous situation

which, if not avoided, will result in death or serious injury.

WARNING: Indicates a potentially hazardous situation

which, if not avoided, could result in death or serious injury.

CAUTION: Indicates a potentially hazardous situation which,

if not avoided, may result in minor or moderate injury.

NOTICE: Indicates a practice not related to personal injury

which, if not avoided, may result in property damage.

IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR

ANY D

EWALT TOOL, CALL US TOLL FREE AT: 1-800-4-DEWALT

(1-800-433-9258).

WARNING: To reduce the risk of injury, read the instruction

manual.

Important Safety Instructions

• Read these instructions.

• Keep these instructions.

• Heed all warnings.

• Follow all instructions.

• Only use attachments/accessories specified by the manufacturer.

• Refer all servicing to qualified service personnel. Servicing is

required when the apparatus has been damaged in any way,

the apparatus has been exposed to rain or moisture, does not

operate normally, or has been dropped.

2

English

performed. Use of the hand-held radar scanner for operations

different from those intended could result in a hazardous

situation.

Battery Tool Use and Care

a) Recharge only with the charger specified by DEWALT. A

charger that is suitable for one type of battery pack may create

a risk of fire when used with another battery pack.

b) When battery pack is not in use, keep it away from other

metal objects like paper clips, coins, keys, nails, screws,

or other small metal objects that can make a connection

from one terminal to another. Shorting the battery terminals

together may cause burns or a fire.

c) Under abusive conditions, liquid may be ejected from

the battery; avoid contact. If contact accidentally occurs,

flush with water. If liquid contacts eyes, additionally seek

medical help. Liquid ejected from the battery may cause

irritation or burns.

Safety Information for Hand-Held Radar

Scanners

WARNING: Do not disassemble or modify the hand-held

radar scanner. There are no serviceable parts inside. If you need

assistance, contact D

EWALT at 1-800-4-DEWALT (1-800-433-9258)

or go to http://www.dewalt.com on the Internet.

• Do not operate the hand-held radar scanner in explosive

atmospheres, such as in the presence of flammable liquids,

gases, or dust. Hand-held radar scanners create sparks which

may ignite the dust or fumes.

• The hand-held radar scanner should only be used with

specifically designated D

EWALT batteries. Use of any other

batteries may create a risk of fire.

• Store the hand-held radar scanner out of reach of children

and other untrained persons. Tools are dangerous in the hands

of untrained users.

• Do not disassemble the hand-held radar scanner. There are

no user serviceable parts inside.

• Do not remove or deface warning labels.

• The hand-held radar scanner must remain in contact with

the wall surface during the entire scan.

• Optimal operation of the hand-held radar scanner is possible

only when the operating instructions are read and followed.

• Do not attach any stickers on name plates to the sensor

area on the back of the hand-held radar scanner. Metal

stickers especially could affect the measurement results.

• Before turning on the hand-held radar scanner, ensure that

its back surface is not moist. If required, wipe with a dry cloth

before scanning.

• Do not expose to extreme temperatures or variations in

temperature. In case of large variations in temperature,

allow the unit to adjust to ambient temperature before

powering on. Extreme and variations in temperature can impair

the display and accuracy of the tool.

• Static electricity may lead to inaccurate detection of

electrical wires.

WARNING: Do not expose hand-held radar scanner or

battery to excessive heat such as sunshine, fire or the like.

WARNING: Modifications not authorized by the manufacturer

may void user's authority to operate this device.

WARNING: The detector alone should not be relied on

exclusively to locate items below the scanned surface. Under

certain circumstances, the scanner may not identify all objects or

the exact location of objects. Use other information sources to help

locate items before penetrating the surface. Such additional sources

include construction plans, visible points of entry of pipes and wiring

3

English

into walls, such as in a basement, and standard 16" (40 cm) and 24"

(60 cm) stud spacing practices.

WARNING: You should always use caution when nailing,

cutting or drilling in ceilings, walls and floors that may contain

wiring or pipes near the surface. Shielded, dead or non-

powered wires will not be detected as live wires. Remember that

studs or joists are normally spaced 16" (40 cm) or 24" (60 cm) apart

and are usually 1-1/2" (38mm) in width. Beware of anything closer

together or a different width. Always turn the power off when working

near electrical wires. Also, shut off gas and water supplies.

WARNING: To reduce the risk of injury and electric shock,

always turn off power when working near electrical wires. Metal

shielded wires or those in metal conduit will not be detected. Use

extreme caution in these circumstances or whenever live AC wiring

is present. Test the functionality of the AC, detect on a well known

power supply prior to measurement.

WARNING: Live wires deeper than 2" (50.8 mm) from the

surface, in plastic conduit, behind plywood sheer wall or

metallic wall coverings, cables operating at DC current or wires

used in telecommunications and computer systems may not be

detected. Wires that are not live may be detected as metal objects.

WARNING: Do not use the tool to detect AC voltage in

un-insulated, exposed or free wires. Do not use as a substitute

for a volt meter.

WARNING: Detection values can be impaired through certain

ambient conditions. These include the proximity of other equipment

that produce strong magnetic or electromagnetic fields, moisture,

metallic building materials, foil laminated insulation materials or

conductive wall paper or tiles. Use of transmitting systems such as

WLAN, UMTS, radar, transmitting masts or microwaves can influence

the measurements.

CAUTION: Do not use on humans or animals. This is not for

human or animal use and can cause injury if used.

CAUTION: When not in use, place hand-held radar scanner

on its side on a stable surface where it will not cause a tripping

or falling hazard. Some tools with large battery packs will stand

upright on the battery pack but may be easily knocked over.

• The label on your tool may include the following symbols. The

symbols and their definitions are as follows:

V ................... volts A ......................amperes

Hz ................. hertz W .....................watts

min ............... minutes

or AC ..........alternating

or DC ... direct current current

.................Class I Construction or AC/DC ...alternating

.....................

(grounded) ........................or direct

................. Class II Construction current

(double insulated)

n

o ....................no load

…/min .......... per minute speed

BPM .............beats per minute

n ......................rated

IPM ............... impacts per minute

........................speed

RPM ............. revolutions per

.....................earthing

minute terminal

sfpm .............surface feet

..................... safety alert

..................... per minute symbol

SPM ............. strokes per minute

Detection through Special Surface

Conditions

WALLPAPER

The hand-held radar scanner will function normally on walls covered

with wallpaper or fabric, unless the materials are metallic foil, contain

metallic fibers or are still wet after application.

4

English

against harmful interference in a residential installation. This equipment

generates, uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If

this equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment off and

on, the user is encouraged to try to correct the interference by one or

more of the following measures:

– Reorient or relocate the receiving antenna.

– Increase the separation between the equipment and receiver.

– Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

– Consult the dealer or an experienced radio/TV technician for help.

Important Safety Instructions for All

Battery Packs

When ordering replacement battery packs, be sure to include catalog

number and voltage. Consult the chart at the end of this manual for

compatibility of chargers and battery packs.

The battery pack is not fully charged out of the carton. Before using

the battery pack and charger, read the safety instructions below, then

follow charging procedures outlined.

READ ALL INSTRUCTIONS

• Do not charge or use battery in explosive atmospheres,

such as in the presence of flammable liquids, gases or dust.

Inserting or removing the battery from the charger may ignite the

dust or fumes.

• NEVER force battery pack into charger. DO NOT modify

battery pack in any way to fit into a non-compatible charger

as battery pack may rupture causing serious personal injury.

PLASTER AND LATH

Due to the uneven thickness of plaster, it may be difficult to locate

studs. It may be easier to identify the metal nail heads in the studs. If

the plaster is reinforced with wire mesh, the hand-held radar scanner

will not be able to reliably detect objects behind it.

TEXTURED OR ACOUSTICAL WALLS AND CEILINGS

When scanning a wall or ceiling with an uneven surface, place thin

cardboard on the surface and scan over the cardboard.

WOOD FLOORING, WOOD SUB-FLOORING AND DRYWALL

OVER PLYWOOD

Due to the thickness of these materials, it may be difficult to detect a

wood stud or joist. It may be easier to detect the metal nails that hold

the materials to the stud or joist.

CARPETING

The hand-held radar scanner cannot detect studs or joists through

carpeting. It may be easier to detect the metal nails that hold the

materials to the stud or joist.

NOTE: Sensing depth and accuracy can vary due to moisture,

content of the materials, wall texture and paint.

Regulatory Notices

• This Class B digital apparatus complies with Canadian ICES-003.

• This device complies with Part 15 of the FCC Rules. Operation is

subject to the following two conditions:

1. This device may not cause harmful interference, and

2. This device must accept any interference received, including

interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with

the limits for a Class B digital device, pursuant to Part 15 of the FCC

Rules. These limits are designed to provide reasonable protection

5

English

Consult the chart at the end of this manual for compatibility of

batteries and chargers.

• Charge the battery packs only in D

EWALT chargers.

• DO NOT splash or immerse in water or other liquids.

• Do not store or use the tool and battery pack in locations

where the temperature may reach or exceed 105 °F (40 ˚C)

(such as outside sheds or metal buildings in summer).

WARNING: Fire hazard. Never attempt to open the battery pack

for any reason. If battery pack case is cracked or damaged, do not

insert into charger. Do not crush, drop or damage battery pack. Do

not use a battery pack or charger that has received a sharp blow,

been dropped, run over or damaged in any way (i.e., pierced with a

nail, hit with a hammer, stepped on). Damaged battery packs should

be returned to service for recycling.

WARNING: Fire hazard. Do not store or carry battery so

that metal objects can contact exposed battery terminals.

For example, do not place battery in aprons, pockets, tool boxes,

product kit boxes, drawers, etc., with loose nails, screws, keys, etc.

Transporting batteries can possibly cause fires if the battery

terminals inadvertently come in contact with conductive

materials such as keys, coins, hand tools and the like. The US

Department of Transportation Hazardous Material Regulations (HMR)

actually prohibit transporting batteries in commerce or on airplanes

(i.e., packed in suitcases and carry-on luggage) UNLESS they are

properly protected from short circuits. So when transporting individual

batteries, make sure that the battery terminals are protected and well

insulated from materials that could contact them and cause a short

circuit.

SPECIFIC SAFETY INSTRUCTIONS FOR LITHIUM ION (Li-Ion)

• Do not incinerate the battery pack even if it is severely

damaged or is completely worn out. The battery pack can

explode in a fire. Toxic fumes and materials are created when

lithium ion battery packs are burned.

• If battery contents come into contact with the skin,

immediately wash area with mild soap and water. If battery

liquid gets into the eye, rinse water over the open eye for 15

minutes or until irritation ceases. If medical attention is needed,

the battery electrolyte is composed of a mixture of liquid organic

carbonates and lithium salts.

• Contents of opened battery cells may cause respiratory

irritation. Provide fresh air. If symptoms persists, seek medical

attention.

WARNING: Burn hazard. Battery liquid may be flammable if

exposed to spark or flame.

The RBRC™ Seal

The RBRC™ (Rechargeable Battery Recycling

Corp oration) Seal on the nickel cadmium, nickel metal

hydride or lithium ion batteries (or battery packs) indicate

that the costs to recycle these batteries (or battery

packs) at the end of their useful life have already been paid by D

EWALT.

In some areas, it is illegal to place spent nickel cadmium, nickel metal

hydride or lithium ion batteries in the trash or municipal solid waste

stream and the RBRC program provides an environmentally conscious

alternative.

RBRC™ in cooperation with D

EWALT and other battery users, has

established programs in the United States and Canada to facilitate

the collection of spent nickel cadmium, nickel metal hydride or lithium

ion batteries. Help protect our environment and conserve natural

resources by returning the spent nickel cadmium, nickel metal hydride

or lithium ion batteries to an authorized D

EWALT service center or

to your local retailer for recycling. You may also contact your local

recycling center for information on where to drop off the spent battery.

RBRC™ is a registered trademark of the Rechargeable Battery

Recycling Corporation.

6

English

Important Safety Instructions for All

Battery Chargers

SAVE THESE INSTRUCTIONS: This manual contains important

safety and operating instruc tions for battery chargers.

• Before using charger, read all instructions and cautionary markings

on charger, battery pack, and product using battery pack.

WARNING: Shock hazard. Do not allow any liquid to get inside

charger. Electric shock may result.

CAUTION: Burn hazard. To reduce the risk of injury, charge only

D

EWALT rechargeable batteries. Other types of batteries may burst

causing personal injury and damage.

NOTICE: Under certain conditions, with the charger plugged in to the

power supply, the charger can be shorted by foreign material. Foreign

materials of a conductive nature such as, but not limited to, grinding

dust, metal chips, steel wool, aluminum foil, or any buildup of metallic

particles should be kept away from charger cavities. Always unplug the

charger from the power supply when there is no battery pack in the

cavity. Unplug charger before attempting to clean.

• DO NOT attempt to charge the battery pack with any

chargers other than the ones in this manual. The charger and

battery pack are specifically designed to work together.

• These chargers are not intended for any uses other than

charging D

EWALT rechargeable batteries. Any other uses may

result in risk of fire, electric shock or electrocution.

• Do not expose charger to rain or snow.

• Pull by plug rather than cord when disconnecting charger.

This will reduce risk of damage to electric plug and cord.

• Make sure that cord is located so that it will not be stepped

on, tripped over, or otherwise subjected to damage or

stress.

• Do not use an extension cord unless it is absolutely

necessary. Use of improper extension cord could result in risk of

fire, electric shock, or electrocution.

• When operating a charger outdoors, use an extension cord

suitable for outdoor use. Use of a cord suitable for outdoor use

reduces the risk of electric shock.

• An extension cord must have adequate wire size (AWG

or American Wire Gauge) for safety. The smaller the gauge

number of the wire, the greater the capacity of the cable, that is

16 gauge has more capacity than 18 gauge. An undersized cord

will cause a drop in line voltage resulting in loss of power and

overheating. When using more than one extension to make up the

total length, be sure each individual extension contains at least the

minimum wire size. The following table shows the correct size to

use depending on cord length and nameplate ampere rating. If in

doubt, use the next heavier gauge. The smaller the gauge number,

the heavier the cord.

Minimum Gauge for Cord Sets

Ampere Rating

Volts Total Length of Cord in Feet (meters)

120V 25 (7.6) 50 (15.2) 100 (30.5) 150 (45.7)

240V 50 (15.2) 100 (30.5) 200 (61.0) 300 (91.4)

More

Than

Not More

Than

AWG

0 6 18 16 16 14

610 18 16 14 12

10 12 16 16 14 12

12 16 14 12 Not Recommended

• Do not place any object on top of charger or place the

charger on a soft surface that might block the ventilation

slots and result in excessive internal heat. Place the charger

in a position away from any heat source. The charger is ventilated

through slots in the top and the bottom of the housing.

7

English

• Do not operate charger with damaged cord or plug.

• Do not operate charger if it has received a sharp blow, been

dropped, or otherwise damaged in any way. Take it to an

authorized service center.

• Do not disassemble charger; take it to an authorized service

center when service or repair is required. Incorrect reassembly

may result in a risk of electric shock, electrocution or fire.

• Disconnect the charger from the outlet before attempting

any cleaning. This will reduce the risk of electric shock.

Removing the battery pack will not reduce this risk.

• NEVER attempt to connect two chargers together.

• The charger is designed to operate on standard 120V

household electrical power. Do not attempt to use it on any

other voltage. This does not apply to the vehicular charger.

Chargers

Your tool uses a DEWALT charger. Be sure to read all safety instructions

before using your charger. Consult the chart on the back cover of this

manual for compatibility of chargers and battery packs.

FIG. 1

A

Charging Procedure (Fig. 1)

1. Plug the charger into an appropriate outlet before inserting battery

pack.

2. Insert the battery pack (A) into the charger, as shown in Figure 1,

making sure the pack is fully seated in charger. The red (charging)

light will blink continuously indicating that the charging process

has started.

3. The completion of charge will be indicated by the red light

remaining ON continuously. The pack is fully charged and may be

used at this time or left in the charger.

Charge Indicators

Some chargers are designed to detect certain problems that can arise

with battery packs. Problems are indicated by the red light flashing at

a fast rate. If this occurs, re-insert battery pack into the charger. If the

problem persists, try a different battery pack to determine if the charger

is OK. If the new pack charges correctly, then the original pack is

defective and should be returned to a service center or other collection

site for recycling. If the new battery pack elicits the same trouble

indication as the original, have the charger tested at an authorized

service center.

HOT/COLD PACK DELAY

Some chargers have a Hot/Cold Pack Delay feature: when the charger

detects a battery that is hot, it automatically starts a Hot Pack Delay,

suspending charging until the battery has cooled. After the battery

has cooled, the charger automatically switches to the Pack Charging

mode. This feature ensures maximum battery life. The red light flashes

long, then short while in the Hot/Cold Pack Delay mode.

LEAVING THE BATTERY PACK IN THE CHARGER

The charger and battery pack can be left connected with the charge

indicator showing Pack Charged.

WEAK BATTERY PACKS: Weak batteries will continue to function

but should not be expected to perform as much work.

8

English

FAULTY BATTERY PACKS: This charger will not charge a faulty

battery pack. The charger will indicate faulty battery pack by refusing

to light or by displaying problem pack or charger.

NOTE: This could also mean a problem with a charger.

Important Charging Notes

1. Longest life and best performance can be obtained if the battery

pack is charged when the air temperature is between 65 °F and

75 °F (18–24 °C). DO NOT charge the battery pack in an air

temperature below +40 °F (+4.5 °C), or above +105 °F (+40.5 °C).

This is important and will prevent serious damage to the battery

pack.

2. The charger and battery pack may become warm to touch while

charging. This is a normal condition, and does not indicate a

problem. To facilitate the cooling of the battery pack after use,

avoid placing the charger or battery pack in a warm environment

such as in a metal shed, or an uninsulated trailer.

3. If the battery pack does not charge properly:

a. Check operation of receptacle by plugging in a lamp or other

appliance;

b. Check to see if receptacle is connected to a light switch which

turns power off when you turn out the lights;

c. Move charger and battery pack to a location where the

surrounding air temperature is approximately 65 °F–75 °F

(18–24 °C);

d. If charging problems persist, take the tool, battery pack and

charger to your local service center.

4. The battery pack should be recharged when it fails to produce

sufficient power on jobs which were easily done previously. DO

NOT CONTINUE to use under these conditions. Follow the

charging procedure. You may also charge a partially used pack

whenever you desire with no adverse affect on the battery pack.

5. Foreign materials of a conductive nature such as, but not limited

to, grinding dust, metal chips, steel wool, aluminum foil, or any

buildup of metallic particles should be kept away from charger

cavities. Always unplug the charger from the power supply when

there is no battery pack in the cavity. Unplug charger before

attempting to clean.

6. Do not freeze or immerse charger in water or any other liquid.

WARNING: Shock hazard. Don’t allow any liquid to get inside

charger. Electric shock may result.

CAUTION: Never attempt to open the battery pack for any reason.

If the plastic housing of the battery pack breaks or cracks, return to

a service center for recycling.

Storage Recommendations

1. The best storage place is one that is cool and dry away from direct

sunlight and excess heat or cold.

2. For long storage, it is recommended to store a fully charged

battery pack in a cool dry place out of the charger for optimal

results.

NOTE: Battery packs should not be stored completely depleted of

charge. The battery pack will need to be recharged before use.

SAVE THESE INSTRUCTIONS

FOR FUTURE USE

9

English

COMPONENTS (Fig. 2)

WARNING: Never modify the hand-held radar scanner or any part

of it. Damage or personal injury could result.

A. 12V Max* Lithium-ion battery pack

B. Handle

C. Wheels

D. Sensor area

E. Center alignment line

F. Display

G.

Power on/off button

H.

Left/up arrow button

I.

OK button

J.

Right/down arrow button

K.

Main menu button

INTENDED USE

The hand-held radar scanner is designed to help locate objects behind

a wall surface. It can be used on surfaces including drywall, plywood,

OSB, ceramic tile, marble and concrete.

Items detected include wood studs, ferrous metal, non-ferrous metal,

live electric wires and PVC pipes.

The hand-held radar scanner is intended for indoor use only.

Please read the entire manual before using the hand-held radar

scanner.

The hand-held radar scanner is a professional tool. DO NOT let

children come into contact with the tool. Supervision is required when

inexperienced operators use this tool.

FIG. 2

B

A

C

D

F

E

K

H

I

G

J

N

Belt Hook (Fig.3)

(Optional Accessory)

WARNING: To reduce the risk of serious

M

L

FIG. 3

personal injury, DO NOT suspend tool

overhead or suspend objects from the belt

hook. ONLY hang tool’s belt hook from a work

belt.

WARNING: To reduce the risk of serious

10

English

personal injury, ensure the screw (L) holding the belt hook is

secure.

IMPORTANT: When attaching or removing the belt hook, use only the

screw (L) that is provided.

The belt hook (M) can be attached to either side of the tool using only

the screw (L) provided, to accommodate left- or right-handed users. If

the hook is not desired at all, it can be removed from the tool.

To move the belt hook, remove the screw (L) that holds the belt hook

in place, then reassemble on the opposite side.

OPERATION

Installing and Removing the Battery Pack

(Fig.4)

NOTE: Make sure your battery pack is fully charged.

N

FIG. 4

A

To install the battery pack (A) into the tool handle, align the battery

with the rails inside the tool’s handle and slide it into the handle until

the battery pack is firmly seated in the tool and ensure that it does not

disengage.

To remove the battery pack from the tool, press the release button (N)

and firmly pull the battery pack out of the tool handle. Insert it into the

charger as described in the charger section of this manual.

Getting Started

POWER ON/OFF

1. To turn on the hand-held radar scanner, press the power on/off

button (G) and hold for 0.5 seconds. Ensure that the unit is at least

6" away from the wall when powering on.

2. To turn off the hand-held radar scanner, press the power on/off

button (G) and hold for 2 seconds.

The hand-held radar scanner will also power off automatically after

15minutes of inactivity.

INITIAL SETUP

Press the power button (G) to turn on the hand-held radar scanner.

The first time the hand-held radar scanner is powered on, it will prompt

to select a language.

1. Press the right/down arrow button (J) or left/up arrow button (H) to

highlight English, Spanish or French.

2. Press the OK button (I) to confirm selection.

BASIC OPERATION

The hand-held radar scanner identifies objects behind a wall surface

in two steps.

11

English

During the first pass over the wall surface, the pre-scan data mapping

occurs. The hand-held radar scanner will automatically sense and

calibrate for all objects below the wall surface. When the direction of

scan is reversed, the hand-held radar scanner will display the objects

identified.

Step 1. Place unit on wall.

Pre-Scan Mapping: Move in a

straight line across wall surface.

Step 2. Display Scanned

Objects: Reverse scan direction

to display identified objects.

The hand-held radar scanner can analyze between a 1foot to 9.8foot

(0.3m to 3 m) section of wall.

The pre-scan data mapping process can begin in any direction.

The hand-held radar scanner will automatically change to displaying

objects when the initial scan direction is reversed.

The hand-held radar scanner can be used either horizontally or

vertically.

SCANNING PROCESS

1. The screen below will indicate that the hand-held radar scanner is

ready to start a new scan.

2. Place the hand-held radar scanner on the wall to start a new scan.

3. Move the hand-held radar scanner along the wall surface in a

straight line. The screen below will appear indicating the pre-scan

data mapping is in process.

12

English

4. The hand-held radar scanner has a scannable range of 9.8feet

(3meters) of wall section. The yellow memory bar will fill, indicating

how much of the available range is used. As the distance limit is

approached, the memory bar will turn red.

5. Reverse scanning direction to read the mapped data. The main

viewing screen below will appear.

Ensure that the wheels are in contact with the wall surface during the

entire pre-scan data mapping and scanning passes.

MAIN VIEWING SCREEN

The main viewing screen contains several sections of information.

P

Q

R

O

S

O. Main Scanning Window

P. Confidence Meter

Q. Material Identification Window

R. Battery Fuel Gauge

S. Tracking Bar

Main Scanning Window

The main scanning window (O) will give a graphical representation of

the item identified below the wall surface.

Items identified include wood, ferrous metal, non-ferrous metal, plastic

and live electric wires.

Wood Live Electric Ferrous Metal

13

English

– Do not touch the surface being scanned with your other hand or

any other part of the body as it interferes with scanning.

– Review Detection through Special Surface Conditions

section of the manual.

Material Identification Window

The material identification window (Q) will give further detail of the item

identified below the wall surface. Multiple items could be displayed if

they are all directly below the hand-held radar scanner's position.

Items identified include:

Wood Metal (Ferrous) Metal (Non-Ferrous)

Plastic Live Electric

NOTE: When the hand-held radar scanner is directly over a live wire,

the live electric graphic will appear in the main scanning window (O)

and the live electric icon will blink in the material identification window

(Q).

When the hand-held radar scanner is near, but not directly over a live

wire, the live electric icon will blink in the material identification window

(Q). This indicates that there is live electric in the vicinity of the hand-

held radar scanner.

Non-Ferrous Metal Plastic / PVC

Arrow indicators will appear to guide to the center of an object. Once

the object center is detected, a center line icon will appear. The

alignment lines (Fig. 2, E) on top of the hand-held radar scanner can

then be used to guide marking the wall.

Confidence Meter

The confidence meter (P) gives a relative indication of signal strength.

A fully lit confidence meter indicates a strong data signal and high

confidence of the material identified below the surface.

A partially lit confidence meter indicates a weaker signal and less

confidence of the material identified below the wall.

To improve the signal strength, follow these tips:

– Scan in a straight line, either horizontal or vertical.

– Scan uniformly without lifting from the surface of the wall.

– Always scan SLOWLY to achieve maximum sensitivity.

14

English

Battery Fuel Gauge

The display on the hand-held radar scanner includes a

battery fuel gauge (R) which consists of four yellow

segments that indicate the level of charge remaining in the

12V Max* battery pack. When the level of charge in the

battery is below the usable limit, the last segment of the

battery fuel gauge will turn red to indicate that the battery

will need to be recharged.

NOTE: The battery fuel gauge is only an indication of the charge left

on the battery pack. It does not indicate product functionality and is

subject to variation based on product components, temperature and

end-user application.

Tracking Bar

The tracking bar (S) at the bottom of the main viewing screen gives a

macro overview of the number of objects located during the pre-scan

data mapping process.

The current position of the hand-held radar scanner is indicated by the

brackets and shaded area.

The tracking bar can be helpful in indicating which way to move the

hand-held radar scanner to identify additional objects behind the wall

surface.

Error Messages

SCANNING TOO FAST

If the scanning speed exceeds the maximum processing speed of the

hand-held radar scanner, the below error message will appear:

Remove the hand-held radar scanner from the wall.

When the "Begin Scanning" screen appears on the display, place the

hand-held radar scanner on the wall to restart the scan.

SCANNING TOO SLOW

If the scanning speed is below the minimum processing speed of the

hand-held radar scanner, the following error message will appear:

Remove the hand-held radar scanner from the wall.

When the "Begin Scanning" screen appears on the display, place the

hand-held radar scanner on the wall to restart the scan.

15

English

BATTERY LOW

If the 12V Max* battery pack is about to run out of charge, the

following error message will appear:

Replace or recharge the 12V Max* battery pack.

LOST CONTACT WITH THE WALL SURFACE

If the hand-held radar scanner loses contact with the wall surface, the

following error message will appear:

Remove the hand-held radar scanner from the wall.

When the "Begin Scanning" screen appears on the display, place the

hand-held radar scanner on the wall to restart the scan.

MAXIMUM DISTANCE EXCEEDED

The hand-held radar scanner has a maximum scanning range of

9.8 feet (3 meters). If the distance scanned exceeds the maximum

distance, the following error message will appear:

Remove the hand-held radar scanner from the wall.

When the "Begin Scanning" screen appears on the display, place the

hand-held radar scanner on the wall to restart the scan.

Menu Options

Press the menu button (K) to view the menu options.

NOTE: At any time, the menu button may be pressed to navigate up

one level.

1. Press the right/down arrow button (J) or left/up arrow button (H) to

highlight the menu option.

2. Press the OK button (I) to confirm selection.

16

English

LANGUAGE SELECTION

1. Press the right/down arrow button (J) or left/up arrow button (H) to

highlight English, French or Spanish.

2. Press OK (I) to confirm selection.

VIEW TUTORIAL

The hand-held radar scanner includes a tutorial with tips for best

practices.

After completion of the tutorial, the hand-held radar scanner will return

to the main menu.

DISPLAY VERSION

The hand-held radar scanner will display the product software version.

Press the OK button (I) to exit.

RESET FACTORY DEFAULTS

NOTICE: Changing to default setup will erase current settings and

restore factory settings.

1. Press the right/down arrow button (J) or left/up arrow button (H) to

highlight YES or NO.

2. Press the OK button (I) to confirm selection.

3. If YES is selected, the hand-held radar scanner will ask for a

second confirmation to restore factory defaults. Press the right/

down arrow button (J) or left/up arrow button (H) to highlight YES

or NO.

4. Press the OK button (I) to confirm selection.

17

English

Operating Tips

• Use only DEWALT 12V Max* lithium-ion battery.

• Ensure the D

EWALT battery is in good working condition. If the

battery fuel gauge (R) on the main viewing screen has only one red

segment lit, the battery needs to be recharged.

• Scan in a straight line, either horizontal or vertical.

• Scan uniformly without lifting from the surface of the wall.

• Always scan SLOWLY to achieve maximum sensitivity.

• Do not touch the surface being scanned with your other hand or

any other part of the body as it could interfere with scanning.

• Refer to construction plans, visible exits of wires and pipes and

construction techniques. Studs are normally spaced either 16"

(40cm) or 24" (60 cm) apart and are 1-1/2" (38mm) wide. Doors

and windows are often constructed with studs and headers which

are closer together.

• Avoid scanning through materials which have inconsistent density

such as carpet with padding, excessively thick plaster and lath,

freshly painted walls or metallic wall coverings.

• Avoid wearing jewelry such as rings or watches. The metal may

cause inaccurate detection.

• Protect against moisture and direct sunlight.

• Do not place stickers, decals, paint or name plates, especially

metal ones, on the sensor area of the back of the tool.

MAINTENANCE

Cleaning

WARNING: Blow dirt and dust off with clean, dry air at least once

a week. To minimize the risk of eye injury, always wear ANSI Z87.1

approved eye protection when performing this.

WARNING: Never use solvents or other harsh chemicals for

cleaning the non-metallic parts of the tool. These chemicals may

weaken the plastic materials used in these parts. Use a cloth

dampened only with water and mild soap. Never let any liquid get

inside the tool; never immerse any part of the tool into a liquid.

CHARGER CLEANING INSTRUCTIONS

WARNING: Shock hazard. Disconnect the charger from the AC

outlet before cleaning. Dirt and grease may be removed from the

exterior of the charger using a cloth or soft non-metallic brush. Do

not use water or any cleaning solutions.

Troubleshooting

SITUATION PROBABLE CAUSE SOLUTION

Unit does not turn

on

• No power to unit • Make sure 12V Max*

battery pack is fully

charged

• Fully seat the 12V

Max* battery pack in

the handle

Unit does not display

objects; says "Pre-

Scan Data Mapping"

• Unit is in process of

mapping scanned

area

• See section of manual

on pre-scan data

mapping

18

English

SITUATION PROBABLE CAUSE SOLUTION

No materials

detected or difficulty

in detecting objects

• Too narrow of area

mapped

• Difficulty in scanning

below special wall

condition

• Re-map larger area

• Scan slowly

• Scan in a straight line

• Review special wall

conditions section of

the manual

• Scan in both the

horizontal and vertical

directions

• Ensure that the unit

is at least 6" away

from the wall when

powering on.

Difficulty in detection

of metal

• Metal items too

deep

• Scan in both

horizontal and vertical

straight lines. Metal

sensitivity is increased

when the metal object

is parallel to the

sensor.

Seemingly false

metal detection

• Metal items such

as jewelry are too

close to sensor

area

• Remove jewelry &

re-scan

Difficulty in scanning

near door or

windows

• Double or triple

studs are common

around doors and

windows

• Detect outer edge

instead

SITUATION PROBABLE CAUSE SOLUTION

Area of voltage

detected is larger

than anticipated

• Static charge may

be present on the

wall surface

• Scan a smaller area

• Turn off the electrical

circuit and identify

metal wire instead

• Place your free hand

on the wall to drain

static

Electrical voltage

not detected in area

where it was thought

to be

• Wires are shielded

by metal conduit

• Wires are deeper

than 3 inches

• Wires are not live

• Cannot scan

below special wall

condition

• Review identified

metal in scanning

window to determine

metal conduit

• Plug an item into a

wall outlet to verify live

circuit

• Review special wall

conditions section of

manual

Low confidence

meter reading

• Scanning in a non-

straight line

• Scanning too fast

• Difficulty scanning

below special wall

condition

• Scan slowly

• Scan in a straight line

• Review special wall

conditions section of

the manual

Received error

message: Too fast

• Scanning too fast • Scan slowly

Received error

message: Lost

surface contact

• Hand-held radar

scanner lifted off

wall surface

• Re-map area and

repeat scanning

Cannot get a center

line to appear

• Wall is thick or

dense

• Review special wall

conditions section of

manual

La page charge ...

DeWalt DCT418 Manuel utilisateur

Ce manuel convient également à

DeWalt DCT418 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents