Kichler 35153A Guide d'installation

ITEM #0747612

MODEL #35153

LED CEILING FAN

1

ATTACH YOUR RECEIPT HERE

Serial Number

Purchase Date

Questions, problems, missing parts? Before returning to your retailer, call our customer

service department at 1-800-554-6504, 8 a.m. - 4:30 p.m, EST, Monday - Friday.

Français p. 17

Español p. 33

PACKAGE CONTENTS

2

A

Hanging Bracket

Down Rod

Canopy

Blade Iron

Motor Coupling Cover

Motor Assembly

B

C

D

E

F

1

5

1

PART DESCRIPTION QTY

LED Housing

Light Kit

Canopy Hole Cover

Shade

Blade

H

G

I

J

K

1

5

PART DESCRIPTION QTY

A

K

C

I

E

G

B

D

F

J

H

HARDWARE CONTENTS

3

SAFETY INFORMATION

Hanging bracket Screw

Hanging bracket Washer

Wire Connector

Blade Screw

Balance Kit

HARDWARE BAG REMOTE CONTROL

Remote Control

Receiver

Battery

Wood Screw

Lag Screw

Wire Connector

Blade Iron Screws

Flat Washer + Spring Washer

Please read and understand this entire manual before attempting to assemble, operate or install the

product. If you have any questions regarding the product, please call customer service at

1-800-554-6504, 8 a.m. - 4:30 p.m., EST.

WARNING:

• Important: When using an existing outlet box, be sure the box is securely attached to the building

structure and can support the full weight of the fan. Failure to do so can result in serious injury or

death.

• Turn off circuit breakers and wall switch to the fan supply wire leads. Warning: Failure to

disconnect power supply prior to installation may result in serious injury or death.

• Warning - Connecting this fan to a light switch (on/off) has been known to cause damage to the

receiver. This fan must be wired to continually receive power. Failure to do so will drastically

reduce the lifespan of this fan.

• Do not install fan on a ceiling with a pitch greater than 20°.

• Important: Be sure wiring box is properly grounded or that a ground (green) wire is present.

• Make sure the installation site you choose allows a minimum of 7 feet from the floor to the end of

the blades.

• To reduce the risk of fire or electrical shock, do not use this fan with any solid state fan speed

device or variable speed control.

• Do not touch hot LED

• The LED light output is strong enough to injure human eyes. Precautions must be taken to

prevent looking directly at the LEDs with unaided eyes for more than a few seconds.

WARNING (continued)

CAUTION:

PREPARATION

4

Before beginning assembly of product, make sure all parts are present. Compare parts with package

contents list and diagram. If any part is missing or damaged, do not attempt to assemble the product.

Contact customer service for replacement parts.

Estimated assembly time: 30 minutes to 1 hour.

Tools Required for Assembly (not included): Phillips screwdriver, flathead screwdriver, wire strippers,

electrical tape, ladder, safety glasses.

A B C

ASSEMBLY INSTRUCTIONS

• WARNING-To reduce risk of fire, electric shock, or personal injury, mount to outlet box marked

“Acceptable for Fan Support of 15.9kg (35lbs) or less” and use mounting screws provided with the

outlet box and/or support directly from building structure. Most outlet boxes commonly used for

the support of luminaries are not acceptable for fan support and may need to be replaced.

Consult a qualified electrician if in doubt.

• Warning-Risk of fire, electric shock, or personal injury. Ceiling fans may be either directly

supported from a structural framing member of a building and (see examples in figures A & B) or

may be mounted to an outlet box marked acceptable for fan support of 31.8 kg (70 lbs) to 15.9kg

(35 lbs) (see example in figure C).

• Read and understand all instructions and illustrations completely before proceeding with assembly

and installation of this fixture.

• If you have any doubts about how to install this lighting fixture, or if the fixture fails to operate

completely, please contact a qualified licensed electrical contractor.

• All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts

out, or use any parts that are worn out or broken. Failure to obey this instruction could invalidate

the UL listing, C.S.A. certification, and/or ETL listing of this fixture.

• This fixture is intended for installation in accordance with the National Electric Code (NEC) and all

local code specifications.

• Use ONLY the supplied LED driver to power fixture.

• Driver cable is not intended for use through or concealed behind walls, floors, or ceilings.

• This fixture is for indoor use only.

• Chemical Burn Hazard. Keep batteries away from children. This remote contains a lithium button

cell battery. If a new or used lithium button/coin cell battery is swallowed or enters the body, it can

cause severe internal burns and can lead to death in as little as 2 hours. Always completely

secure the battery compartment. If the battery compartment does not close securely, stop using

the product, remove the batteries, and keep it away from children. If you think batteries might

have been swallowed or placed inside any part of the body, seek immediate medical attention.

• Dispose of cells properly and keep away from children. Even used cells may cause injury.

ASSEMBLY INSTRUCTIONS

5

1. Secure the hanging bracket (A) to the ceiling outlet

box using hanging bracket screws and hanging

bracket washers.

Important: If attaching the fan to a sloped ceiling,

make sure open end of mounting bracket is installed

facing the roof. Do not install fan on a ceiling with a

pitch greater than 20°.

2. Loosen the set screws found on coupling on top of the motor assembly (F). Then remove the hair

and clevis pin that will be used on a later step.

1

A

Outlet Box

Hair Pin

Safety Cable

Clevis Pin

2

F

Coupling

6

ASSEMBLY INSTRUCTIONS

3. Insert down rod (B) through canopy (C), canopy hole cover (I), and motor coupling cover (E).

Feed wires from the motor assembly (F) through the down rod (B), then insert the down rod (B)

into the coupling found on top of the motor assembly (F).

4. Pass the clevis pin through the down rod (B) and coupling found on the motor assembly (F) then

secure with the hair pin. Tighten set screws found on the coupling on the motor assembly (F).

Hair Pin

Clevis Pin

Coupling

B

F

4

F

I

C

E

B

3

7

ASSEMBLY INSTRUCTIONS

5. Carefully lift the fan and seat the downrod (B)/hanger

ball assembly on the hanging bracket (A). Be sure

the groove in the ball is lined up with the tab on the

hanging bracket (A).

B

A

5

6. For Canadian installation and for USA fans over 35

lbs, the safety cable must be installed into the house

structure beams using a 3” lag screw. Make sure

that when the safety cable is fully extended the lead

wires are longer than the cable and no stress is

placed on the lead wires.

Safety

Cable

Lag

Screw

Safety

Cable

Flat

Washer

Spring

Washer

6

Safety

Cable

ASSEMBLY INSTRUCTIONS

8

7. Wiring the fan per wiring diagram and securely connect wires with wire connectors: Wrap electrical

tape (not included) around each wire connector and make sure no bare wire or wire strands are

visible after making connections.

• Connect WHITE wire from the fan to WHITE wire marked TO MOTOR N from the receiver.

• Connect BLUE wire from the fan to BLUE wire marked FOR LIGHT from the receiver.

• Connect BLACK wire from the fan to BLACK wire marked TO MOTOR L from the receiver.

• Connect BLACK wire from the outlet box to BLACK wire marked AC IN L from the receiver.

• Connect WHITE wire from the outlet box to WHITE wire marked AC IN N from the receiver.

• Connect GROUND (GREEN) wires from hanger bracket and downrod ball, to GROUND (GREEN

or BARE COPPER) from house.

7

OUTLET BOX

BLACK

(LIVE)

WHITE

(NEUTRAL)

BLACK

(AC

INPUT)

WHITE

(AC

INPUT)

WHITE

(NEUTRAL) WHITE

BARE COPPER

(GROUND)

GREEN (BRACKET)

GREEN (DOWN ROD)

BLUE (LIGHT)

BLACK (MOTOR) BLACK

BLUE

ASSEMBLY INSTRUCTIONS

9

8. Install the batteries (3-Volt 2032) into the

remote. Make sure the batteries are seated

correctly in each recess with the positive

symbol facing up, then replace battery cover.

Test the remote control by pushing any button.

A blue light should illuminate. If no blue light

appears make sure the batteries are seated

properly.

This fans control system is

equipped with 16 code combinations to

prevent possible interference from or to

other remote units. The frequency switches

on your receiver and remote control have been

preset at the factory. Remove the remote control

battery cover and make sure the switches

are set to the same position. This must be

done so that your fan will communicate

properly. If you are using more than one fan

in the same area and want to control them

separately, change one fan’s dip switch

settings in the remote control and receiver to a

new pattern.

NOTE: If not using for long periods of time,

remove battery to prevent damage to

remote control. Store the remote away from

excessive heat or humidly.

9. Once wiring step has been completed, slide the

wired remote receiver in between the hanging

bracket (A) and the top of the downrod ball (B) with

the flat side of the receiver facing the ceiling. Turn

lead wires upward and carefully push them into the

outlet box, with the white and green wires to one

side of the box and the black wires toward the other

side.

9

A

B

8

REMOTE CONTROL

RECEIVER

ON

ECE

ON ECE

ASSEMBLY INSTRUCTIONS

10

12. Pass blade iron (D) over blade (K) and secure to

arms with blade iron screws.

Repeat for remaining blade irons.

11. Attach blade (K) to the arm on the motor assembly

(F) with blade screws. Do not tighten blade screws

until each screw has been started. Then, tighten

each screw starting with the center screw.

Repeat for remaining blades

10. Loosen the two shoulder screws without fully

removing the hanging bracket (A). Assemble canopy

(C) by rotating keyhole slot in canopy over shoulder

screws in hanging bracket (A). Tighten shoulder

screws. Securely attach and tighten the canopy hole

cover (I) over the shoulder screws in the hanging

bracket (A) utilizing the keyhole slot twist-lock

feature.

10

A

C

I

Shoulder

Screw

11

F

Arm

K

D

12

Arm

ASSEMBLY INSTRUCTIONS

11

13. Remove the mounting screw marked with a red dot label from the motor assembly (F) and loosen

but do not remove the other 2. Feed the wires from the motor assembly (F) through the center

hole in the LED housing (G). Position keyhole slots around the screws and twist clockwise. Insert

the screw that you had previously removed. Tighten all screws.

13

F

G

ASSEMBLY INSTRUCTIONS

12

14.Connect wires from the motor assembly (F) to the LED kit (H). Remove 1 of 3 screws from the

LED housing (G) and loosen the other 2. Position keyhole slots around the screws and twist

clockwise. Insert the screw that you had previously removed. Tighten all screws.

H

G

F

14

ASSEMBLY INSTRUCTIONS

13

OPERATING INSTRUCTIONS

15.Screw shade (J) onto LED housing (G).

15

G

J

Speed Buttons:

Low Speed

Medium Speed

High Speed

Power Button:

This button turns the fan motor off and is also

used in the program procedure.

Light Buttons:

These two buttons turn the light ON and OFF

as well as controlling the brightness setting.

Directional Button:

This button changes the fan direction from

forward to reverse.

• In warmer weather, counterclockwise movement of the fan will result in downward

airflow creating a wind chill effect.

• In cooler weather, clockwise movement of the fan will result in upward airflow that can

help move stagnant hot air off the ceiling area.

14

STEPS TO BALANCING THE CEILING FAN

Balancing Weight

Plastic Clip

5G

• Tighten screws on the mounting bracket, outlet box, the downrod , fan blades to blade holders,

and blade holders to the motor housing.

• Measure the distance from the tip of each blade to the ceiling. All blades should have the same

vertical distance from the ceiling. Adjust any bent blade holder, by gently pressing up or down on

the brackets, until all blades are at an equal distance from the ceiling.

If wobbling persists, you may need a blade balancing kit to stabilize the ceiling fan. A blade

balancing kit consists of a plastic clip and two balancing weights.

Determining the blade that needs to be balanced is a trial-and-error task.

1. Place a numbered piece of masking tape on each blade so you don't lose track of which blade is

which.

2. One blade at a time, attach the slotted plastic clip over the center of the blade edge and turn the

fan on. Observe which blade has the clip on when the ceiling fan wobbles the least.

3. Place the plastic clip on the edge of the blade, halfway between the blade holder and the blade

tip. Turn fan on and determine improvement.

4. If there is no improvement, turn off the fan again. Slide the clip along the length of the blade to

locate the source of instability.

5. Once you've found the faulty blade, press a balancing weight on the centerline. The weight

should be parallel to the clip.

REMOTE CONTROL

Low

Speed

Reverse

Light

On / Off

Medium Speed

High

Speed

Power

OPERATING INSTRUCTIONS (continued)

15

CARE AND MAINTENANCE

At least twice a each year tighten all screws and lower canopy to check mounting bracket screws

and downrod assembly. Clean fan housing with only a soft brush or lint free cloth to avoid scratching

the finish. Clean blades with a lint free cloth. Shut off main power supply before beginning any

maintenance. Do not use water or a damp cloth to clean the ceiling fan.

FCC WARNING

This device complies with part 15 of the FCC Rules. Operation is subject to the following two

conditions: (1) This device may not cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could void

the user's authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment generates, uses

and can radiate radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the interference by one or more of the

following measures:

Reorient or relocate the receiving antenna, increase the separation between the equipment and

receiver, and connect the equipment into an outlet on a circiut different from that to which the fan is

connected.

WARRANTY

Kichler offers the following limited lifetime warranty to the Original Purchaser of a Kichler Ceiling Fan:

if the Fan’s motor or motor-related parts should fail due to what Kichler, in its sole discretion,

determines to be a defect in material or workmanship, Kichler will, at its option, either repair or

replace the defective part free of charge.

Except as provided below, for one (1) year following the purchase date, if any part other than the

motor or motor-related parts, including, but not limited to, blades, light kits, downrods, switches,

housing, or finish should fail due to what Kichler, in its sole discretion, determines to be a defect in

material or workmanship, Kichler, at its option, will repair or replace the defective part free of charge.

To replace a product that has a warranted defect, the Original Purchaser shall return any allegedly

defective parts or products to the authorized Kichler distributor that the product was purchased from

with PROOF OF PURCHASE, Original Purchaser’s name and return address and a description of the

claimed product defect.

16

WARRANTY (continued)

Rev. 04-16-19

If any of the warranted products are found by Kichler, in its sole discretion, to be defective, such

products will, at Kichler’s sole option and cost, be replaced, repaired or refunded less an amount

directly attributable to Original Purchaser’s prior use of the product. Kichler will return the repaired or

replaced product prepaid freight. This warranty does not cover labor or other costs or expenses to

remove or install any defective, repaired or replaced product.

The parties hereto expressly agree that Original Purchaser’s sole and exclusive remedy against

Kichler shall be for the repair, replacement or refund of defective products as provided herein. This

warranty extends only to product ownership by the Original Purchaser; is not transferable whether to

heirs, subsequent owners, or otherwise; and is void if the Original Purchaser ceases to own the

product.

This warranty does not apply to any products that have been subjected to misuse, mishandling,

misapplication, connected to voltage at more than 5% above standard North American voltage,

unusual use (including but not limited to use in an environment where the annual average ambient

operating temperature is below 27 or above 95 degrees Fahrenheit), neglect (including but not limited

to improper maintenance), accident, acts of god such as high winds, improper installation or care,

failure to follow the Product’s written instructions for normal use and care, improper packaging of

products returned to Kichler, modification (including but not limited to use of unauthorized parts or

attachments), or adjustment or repair. Significant product exposure to chemicals, harsh cleaners, salt

water or salt air will void any and all warranties on exterior finishes. This warranty only applies when

all components, including transformers, have been provided by Kichler. Substituting another

manufacturer’s product and/or components will render the warranty completely void.

THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY ALSO HAVE OTHER

RIGHTS, WHICH VARY FROM STATE TO STATE. SOME STATES DO NOT ALLOW LIMITATIONS

ON HOW LONG AN IMPLIED WARRANTY LASTS OR THE EXCLUSION OR LIMITATION OF

INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE LIMITATIONS OR EXCLUSIONS

MAY NOT APPLY TO YOU.

THE FOREGOING WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR

IMPLIED, INCLUDING THOSE OF MERCHANTABILITY, FITNESS FOR ANY PARTICULAR

PURPOSE OR INFRINGEMENT. ORIGINAL PURCHASER SHALL IN NO EVENT BE ENTITLED

TO, AND KICHLER LIGHTING SHALL NOT BE LIABLE FOR, INDIRECT, SPECIAL, INCIDENTAL

OR CONSEQUENTIAL DAMAGES OF ANY NATURE, INCLUDING, BUT NOT LIMITED TO LOSS

OF PROFIT, PROMOTIONAL AND/OR MANUFACTURING EXPENSES, OVERHEAD, INJURY TO

REPUTATION AND/OR LOSS OF CUSTOMERS.

Printed in China

Distributed by Kichler® LLC.

ARTICLE #0747612

MODÈLE #35153

VENTILATEUR DE PLAFOND À DEL

17

Des questions, des problèmes, des pièces manquantes? Avant de retourner le produit à

votre détaillant, appelez notre service à la clientèle au 1-800-554-6504, entre 8 h et 16 h 30

(HNE) du lundi au vendredi.

JOIGNEZ VOTRE REÇU ICI

Numéro de série

Date d’achat

Distribué par Kichler

®

CONTENU DE L’EMBALLAGE

18

A

Support de suspension

Tige

Pavillon

Support des pales

Cache raccord du moteur

Ensemble moteur

B

C

D

E

F

1

5

1

PIÈCE

DESCRIPTION QT

É

Boîtier DEL

Kit d'éclairage

Cache-trou du pavillon

Abat-jour

Pale

H

G

I

J

K

1

5

PIÈCE

DESCRIPTION QT

É

A

KK

C

II

E

G

B

D

F

J

H

QUINCAILLERIE INCLUSE

19

Vis du support de suspension

Rondelle du support de suspension

Capuchon de connexion

Vis de pale

Ensemble d'équilibrage

SACHET DE QUINCAILLERIE TÉLÉCOMMANDE

TÉLÉCOMMANDE

Récepteur

Pile

Vis à bois

Tire-fond

Capuchon de connexion

Vis du support des pales

Rondelle plate + rondelle ressort

CONSIGNES DE SÉCURITÉ

Veuillez lire et assurez-vous d'avoir compris l’intégralité du présent guide avant d’assembler, d’utiliser ou d’installer ce

produit. Si vous avez des questions concernant ce produit, veuillez appeler le service client au +1-800-554-6504, entre 8h

et 16h30, HNE.

AVERTISSEMENT :

• Important : Lorsque vous utilisez une boîte de sortie existante, assurez-vous que la boîte est fermement attachée à la

structure du bâtiment et peut supporter le poids total du ventilateur. Le non-respect de cette recommandation peut

entraîner des blessures graves ou la mort.

• Coupez les disjoncteurs et l'interrupteur mural qui contrôlent les fils d'alimentation du ventilateur. Avertissement : Si

l'alimentation électrique n'est pas coupée avant l'installation, il peut en résulter de graves blessures ou la mort.

• Avertissement – Connecter ce ventilateur à un interrupteur pour lampe (marche/arrêt) endommage le récepteur. Ce

ventilateur doit être câblé afin de recevoir du courant en continu. Le non-respect de cette recommandation réduira

considérablement la durée de vie de ce ventilateur.

• Ne pas installer sur un plafond incliné à plus de 20°.

• IMPORTANT : Assurez-vous que le boîtier de connexion est correctement mis à la terre ou qu'un fil de terre (vert) est

présent.

• Assurez-vous que le site d'installation choisi offre une hauteur minimum de 2,13 m (7 pi) entre le sol et le dessous

des pales.

• Pour réduire les risques d'incendie ou de choc électrique, n'utilisez pas ce ventilateur avec une commande de vitesse

à semi-conducteurs ou une commande de variation de vitesse.

• Ne touchez pas les DEL chaudes.

• La lumière produite par les DEL est assez puissante pour blesser les yeux humains. Il est impératif de prendre des

précautions pour éviter de recevoir directement dans les yeux non protégés la lumière des DEL pendant plus de

quelques secondes.

AVERTISSEMENT (suite)

ATTENTION:

PRÉPARATION

20

Avant de commencer l’assemblage du produit, assurez-vous que toutes les pièces sont présentes. Comparez les pièces

avec la liste du contenu de l’emballage et la liste de la quincaillerie. En cas de pièces manquantes ou endommagées, ne

tentez pas d’assembler le produit.

Temps d’assemblage approximatif : de 30 à 60 minutes.

Outils nécessaires pour l’assemblage (non inclus) : tournevis cruciforme, tournevis à tête plate, pinces à dénuder, ruban

isolant, escabeau, lunettes de sécurité.

A B C

INSTRUCTIONS POUR L'ASSEMBLAGE

• AVERTISSEMENT – Pour réduire le risque d'incendie, de choc électrique ou de blessures corporelles, installez le

ventilateur sur une boîte de sortie marquée "Convient pour supporter un ventilateur de 15,9 kg (35 lb) maximum" et

utilisez les vis de montage fournies avec la boîte de sortie et/ou fixez directement sur la structure du bâtiment. La

plupart des boîtes de sortie utilisées couramment comme support de luminaires ne conviennent pas au support d'un

ventilateur et devront être remplacées. Consultez un électricien qualifié de cas de doute.

• Avertissement - Risque d'incendie, de choc électrique ou de blessures corporelles. Les ventilateurs de plafond

peuvent être fixés directement sur un élément porteur de la structure du bâtiment (voir exemples sur les figures A et

B) et/ou être montés sur une boîte de sortie marquée "Convient pour supporter un ventilateur de 15,9 kg (35 lb) à

31,8 kg (70 lb)" (voir exemple sur la figure C).

• Risque de brûlure chimique. Gardez les piles hors de portée des enfants. Cette télécommande contient une pile

bouton au lithium. Si une pile bouton au lithium neuve ou usagée est avalée ou pénètre dans le corps, elle peut

entraîner de graves brûlures internes et entraîner la mort en moins de 2 heures. Verrouillez toujours complètement le

compartiment des piles. Si le compartiment des piles ne se ferme pas correctement, cessez d'utiliser l'appareil, retirez

les piles et gardez l’appareil hors de portée des enfants. Si vous pensez que des piles ont pu être avalées ou placées

à l'intérieur d'une partie du corps, consultez immédiatement un médecin.

• Jetez les piles de façon appropriée et conservez-les hors de portée des enfants. Même des piles usagées peuvent

provoquer des blessures.

• Prenez soin de lire et de comprendre l'intégralité des instructions et des illustrations avant de commencer

l’assemblage et l’installation de cet appareil.

• Si vous avez des doutes à propos de l’installation, ou si le luminaire ne fonctionne pas correctement, veuillez

contacter un électricien qualifié agréé.

• Toutes les pièces doivent être utilisées tel qu’indiqué dans ces instructions. Ne remplacez pas les pièces, n'en

laissez pas de côté et ne les utilisez pas si elles sont usées ou brisées. Le non-respect de ces instructions peut

annuler les homologations UL, CSA et/ou ETL de cet appareil.

• Cet appareil est conçu pour une installation en conformité avec le code électrique national des États-Unis (National

Electric Code - NEC) et avec toutes les spécifications du code électrique local.

• Utilisez UNIQUEMENT le pilote de DEL fourni pour faire fonctionner le luminaire.

• Le câble du pilote n'est pas conçu pour une utilisation à travers ou dissimulée derrière les murs, les sols ou les

plafonds.

• Cet appareil est conçu pour une utilisation en intérieur uniquement.

La page charge ...

Kichler 35153A Guide d'installation

Kichler 35153A Guide d'installation

dans d''autres langues

Documents connexes

Autres documents