LG LW6017R Le manuel du propriétaire

LW6017R

EN ENGLISH

FR FRANÇAIS

TYPE: WINDOW

www.lg.com

OWNER’S MANUAL

AIR CONDITIONER

Read this owner’s manual thoroughly before operating the

appliance and keep it handy for reference at all times.

*MFL70960702*

MFL70960702

Rev.03_100620

2

TABLE OF CONTENTS

11 How to Install the Unit

11 Window Requirements

11 Storm Window Requirements

12 Preparation of Chassis

13 Unit Installation

14 OPERATION

14 Control Panel and Remote Control

15 Wireless Remote Control

16 Additional Features

3 SAFETY INSTRUCTIONS

3 IMPORTANT SAFETY INSTRUCTIONS

8 PRODUCT OVERVIEW

8 Exterior Parts

8 Interior Parts

9 INSTALLATION

9 Electrical Data

10 Parts Included

17 MAINTENANCE

17 Air Filter

18 TROUBLESHOOTING

18 Before Calling for Service

18 Normal Sounds You May Hear

21 WARRANTY

3 EN

SAFETY INSTRUCTIONS

READ ALL INSTRUCTIONS BEFORE USE

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always

read and follow all safety messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or injure you and others.

All safety messages will follow the safety alert symbol and either the word WARNING or

CAUTION.

These words mean:

WARNING

You may be killed or seriously injured if you do not follow instructions.

CAUTION

You may be injured or cause damage to the product if you do not follow instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce

the chance of injury, and tell you what may happen if the instructions are not followed.

IMPORTANT SAFETY INSTRUCTIONS

WARNING

injury to persons when using this product, follow basic precautions,

To reduce the risk of explosion, fire, death, electric shock, scalding or

including the following:

INSTALLATION

●Before use, the appliance must be properly installed as described in this manual.

●Contact the authorized service technician for repair or maintenance of this unit.

●Contact the installer for installation of this unit.

●The air conditioner is not intended for use by young children or invalids without supervision.

●Young children should be supervised to ensure that they do not play with the air conditioner.

The following symbols are displayed on units.

This symbol indicates that this appliance uses a flammable refrigerant. If the refrigerant is

is leaked and exposure to an external ignition source, there is a risk of fire.

This symbol indicates that the Operation Manual should be read carefully.

This symbol indicates that a service personnel should be handling this equipment with

reference to the Installation Manual.

This symbol indicates that information is available such as the Operating Manual or

Installation Manual.

4

SAFETY INSTRUCTIONS

●When the power cord is to be replaced, replacement work shall be performed by authorized

●Installation work must be performed in accordance with the National Electric Code by qualified

and authorized personnel only.

personnel only using only genuine replacement parts.

●Connect to a properly rated, protected, and sized power circuit to avoid electrical overload.

●Always plug into a grounded outlet.

●Do not under any circumstances, cut or remove the third (ground) prong from the power cord.

●When installing or moving the appliance, be careful not to pinch, crush, or damage the power

cord.

●Plug in the power plug properly.

●Do not modify or extend the power cord.

●Do not start/stop operation by plugging/unplugging the power cord.

●If the cord/plug is damaged, have it replaced by an authorized service person using authorized

replacement parts.

●Use a dedicated circuit.

●Do not disassemble or modify the product.

●Adhere to all industry recommended safety procedures including the use of long-sleeved gloves

and safety glasses.

●Use care when unpacking and installing. The edges of the product may be sharp.

●Disconnect the power cord or circuit breaker before installing or servicing the appliance.

●Keep packaging materials out of the reach of children. These materials can pose a suffocation

risk to children.

●Store and install the product where it will not be exposed to temperatures below freezing or

●Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any

other appliance.

exposed to outdoor weather conditions.

OPERATION

●Use this appliance only for its intended purpose.

●Never attempt to operate this appliance if it is damaged, malfunctioning, partially disassembled,

or has missing or broken parts, including a damaged cord or plug.

●Repair or immediately replace all power cords that have become frayed or otherwise damaged.

Do not use a cord that shows cracks or abrasion damage along its length or at either end.

●Do not run cord under carpets or mats where it could be stepped on and damaged.

●Keep the cord out from under heavy objects like tables or chairs.

●Do not place the power cord near a heat source.

●Do not use an adaptor or plug the product into a shared outlet.

●Do not tamper with controls.

●If you detect a strange sound, a chemical or burning smell, or smoke coming from the appliance,

●Never unplug the appliance by pulling on the power cord. Always grip the plug firmly and pull

straight out from the outlet.

unplug it immediately, and contact an LG Electronics Customer Information Center.

●Do not grasp the power cord or touch the appliance controls with wet hands.

5 EN

SAFETY INSTRUCTIONS

●If water enters the product, turn off the power at the main circuit, then unplug the product and call

for service.

●If the product has been submerged, contact an LG Electronics Customer Information Center for

instructions before resuming use.

●Unplug the product when unused for long periods.

●Unplug the product before cleaning.

●In the event of a gas leak (propane gas, etc.) do not operate this or any other appliance. Open a

window or door to ventilate the area immediately.

●This appliance is not intended for use by persons (including children) with reduced physical,

sensory or mental capabilities, or lack of experience and knowledge, unless they have been

given supervision or instruction concerning the use of the appliance by a person responsible for

their safety.

●The interior of the product must only be cleaned by an authorized service center or a dealer.

●Do not use solvent-based detergent on the product. Doing so can cause corrosion or damage,

product failure, electrical shock, or fire.

GROUNDING INSTRUCTIONS

●The power cord of this appliance is equipped with a three-prong (grounding) plug. Use this with

a standard three-slot (grounding) wall power outlet to minimize the hazard of electric shock. The

customer should have the wall receptacle and circuit checked by a qualified electrician to make

sure the receptacle is properly grounded. DO NOT CUT OR REMOVE THE THIRD (GROUND)

PRONG FROM THE POWER PLUG.

- Situations when the appliance will be disconnected occasionally; Because of potential safety

hazards, we strongly discourage the use of an adapter plug. However, if you wish to use an

adapter, a TEMPORARY CONNECTION may be made. Use UL-listed adapter, available from

most local hardware stores.

The large slot in the adapter must be aligned with the large slot in the receptacle to assure a

proper polarity connection.

●Attaching the adapter ground terminal to the wall receptacle cover screw does not ground the

appliance unless the cover screw is metal, and not insulated, and the wall receptacle is grounded

through the house wiring. The customer should have the circuit checked by a qualified electrician

to make sure the receptacle is properly grounded.

●Disconnect the power cord from the adapter, using one hand on each. Otherwise, the adapter

ground terminal might break. Do not use the appliance with a broken adapter plug.

- Situations when the appliance will be disconnected often; Do not use an adapter plug in these

situations. Unplugging the power cord frequently can lead to an eventual breakage of the

ground terminal. The wall power outlet should be replaced by a three-slot (grounding) outlet

instead.

6

SAFETY INSTRUCTIONS

CAUTION

To reduce the risk of minor or moderate injury to persons, malfunction, or

damage to the product or property when using this product, follow basic

precautions, including the following:

INSTALLATION

●Take care when installing the product that exhaust or condensation does not damage nearby

property.

●Follow installation instructions exactly to avoid excessive vibration or water leakage.

OPERATION

●This appliance is not intended for use as a precision refrigeration system. Do not use it for special

purposes such as maintaining pets, food, precision machinery, or art objects.

●When installing or moving the appliance, be careful not to pinch, crush, or damage the power

cord.

●Make sure the air inlet and outlet are free from obstructions.

●Use a soft cloth to clean the appliance. Do not use waxes, thinners, or harsh detergents.

●Do not step on or place heavy objects on top of the appliance.

●Do not operate the appliance without the filter securely installed.

●Do not drink water drained from the appliance.

●Be sure to ventilate sufficiently when the air conditioner and a heating appliance such as a heater

are used simultaneously.

●Remove the batteries if the remote control is not to be used for an extended period of time.

●Never mix different types of batteries, or old and new batteries for the remote control.

●Stop using the remote control if there is a fluid leak in the battery. If your clothes or skin are

exposed to the leaking battery fluid, wash off with clean water

●If the leaking battery fluid has been swallowed, rinse the inside of the mouth thoroughly and

consult a doctor.

●Do not recharge or disassemble the batteries.

●Clean the filter every two weeks.

●Never touch the metal parts of the air conditioner when removing the air filter.

MAINTENANCE

●Never use strong cleaning agents or solvents when cleaning the air conditioner or spray water.

Use a smooth cloth.

Do not expose people, animals, or plants to the cold or hot wind from the air conditioner for

extended periods of time.

7 EN

SAFETY INSTRUCTIONS

REFRIGERANT (FOR R32 ONLY)

WARNING

●Do not use means to accelerate the defrosting process or to clean, other than those

recommended by the manufacturer.

●

The appliance shall be stored in a room without continuously operating ignition sources (for

example: open flames, an operating gas appliance or an operating electric heater).

●

Do not pierce or burn. Be aware that flammable refrigerants may not contain an odor.

●

This unit contains flammable refrigerant and has special safety precautions not normally

associated with older units. Please follow all precautions and advisories.

CAUTION

- Use caution while handling and prevent damage to unit. Do not put any holes into product for

any reason. This can cause damage to product and prevent unit from cooling.

- Maintenance and cleaning of unit should be performed by trained personnel. Failure to properly

Service should only be performed by technicians properly trained and certified in the use of

flammable refrigerants. Any service performed by unauthorized servicers/individuals will void all

warranties.

clean unit can result in damage to the refrigeration system and or the electrical system.

-

Make certain that all the air circulation/ventilation openings are free from obstruction.

-

When storing the appliance, do not put in a room with any open flame appliances, such as gas

water heaters or furnaces. Also keep away from electric heaters. Damaged units should be

repaired before storage.

-

SAVE THESE INSTRUCTIONS

8

PRODUCT OVERVIEW

Exterior Parts Interior Parts

1

Evaporator

2

Air Guide

3

4

Compressor

5

6

Condenser

Base Pan

Power Cord

3

4

5

2

1

6

1

Control Panel

2

Remote Control

3

Air Filter

4

5

Cabinet

6

7

Front Grille

Air Outlet

Horizontal Air Deflector (Vertical Louver)

5

4

7

1

3

2

6

9

INSTALLATION

Electrical Data

Power cord may include a current interrupter

device. TEST and RESET buttons are provided

on the plug case. The device should be tested on

TEST button

and then the RESET button. If the TEST button

does not trip or if the RESET button will not stay

engaged, discontinue use of the air conditioner

WARNING

●This appliance should be installed in

accordance with the National Electrical

Code.

●Use of extension cords could cause serious

injury or death.

Do not use an extension cord with this

window air conditioner.

-

Do not use surge protectors or multi-outlet

adapters with this window air conditioner.

-

●Never push the TEST button during

operation. Doing so can damage the plug.

Do not remove, modify, or immerse this

plug. If this device trips, the cause should

be corrected before further use.

-

CAUTION

●The conductors inside this cord are

surrounded by shields, which monitor

leakage current. These shields are not

grounded. Periodically examine the cord

for any damage. Do not use this product

in the event the shields become exposed.

Avoid shock hazard. This unit cannot be

user-serviced. Do not open the tamper-

resistant sealed portion. All warranties and

performance will be voided. This unit is not

intended to be used as an ON/OFF switch.

Use Wall Receptacle Power Supply

Use 15 A, time

delay fuse or 15 A,

circuit breaker.

Standard 120 V, 3-wire

grounding receptacle rated

15 A / 120 VAC / 60 Hz

for 120 V

EN

a periodic basis by first pressing the

and contact a qualified service technician.

10

INSTALLATION

Type 'A' Screws

(14)

Type 'B' Screws

(2)

Tools Needed

Type 'C' Screws

(2)

Right Curtain

Panel

Left Curtain

Panel

Foam strip

(Non-adhesive)

Foam PE(2)

(Adhesive backed)

L bracket (3)

Upper Guide

Phillips-head

screwdriver

Adjustable wrench

Tape measure Pencil

Parts Included (Appearance May Vary)

Level Gloves

Scissors or

Cutting knife

This unit is designed for installation in standard

double hung windows with actual opening widths

from 21" to 35" (533mm to 889mm).

The top and bottom window sashes must open

sufficiently to allow a clear vertical opening of 12"

(305mm) from the bottom of the upper sash to the

inside sill.

●

21" to 35"

12" (305mm) min

1

To prevent vibration and noise, make sure

the unit is installed securely and firmly.

4

Install the unit slightly tilted so the back is

slightly lower than the front (about 1/4"

(6.35mm)). This will force condensed water

to flow to the outside.

5

Install the unit with the bottom between

30"~60" (762mm~1524mm) above the floor

level.

2

Install the unit out of direct sunlight.

3

Fence

Awning

Heat

radiation

Cooled air

CAUTION

●

There should be no obstacles, such as a

fence or wall, within 20" (508mm) from the

back of the cabinet because it will prevent

heat radiation of the condenser.

Restriction of outside air will greatly reduce

the cooling efficiency of the air conditioner.

DO NOT cover or block any of the side and

top louvers. All side louvers of the cabinet

must remain exposed to the outside of the

structure and unobstructed.

●

This product is a window air conditioner.

As such, a standard single-hung or double-hung

window is required for proper installation.

Non-window installations, including using sleeves

or wall openings, and other installation methods

are not recommended.

1

2

If necessary, attach another 1" x 2"

(25.4mm x

50.8mm)

wood strip flush against the back of

the inner sill. This will raise the L bracket, as

shown in the drawing.

Windows that include a storm window frame

may prevent the air conditioner from tilting

down toward the outside to drain properly.

For proper drainage, attach a 1" x 2" (25.4mm x

50.8mm) piece of wood to the inner sill, trimmed

to a length which fits inside the window frame.

The top of the wood shim must be at least 3/4"

(19.05mm) higher than the top of the storm

window frame. Attach the wood securely to the

sill with nails or screws.

Indoors

Inner Sill

Nail or screw

Outer Sill

Storm

Window Frame

Wood Strip Mounted

on Top of Inner Sill

3/4” (19.05mm)

higher than storm

window frame

Wood Strip for

L bracket

L Bracket

Outdoors

NOTE

●

All supporting parts should be secured to firm

wood, masonry, vinyl, fiberglass, or metal.

Storm Window Requirements

Window Requirements

How to Install the Unit

11 EN

INSTALLATION

About

Over

1/4″ (6.35mm)

20″ (508mm)

(762mm~1524mm)

30″~60″

(533mm to 889mm)

5

Install the L bracket behind the inner

window sill, as shown. Use the 2 type A

screws provided.

The bracket helps to hold unit securely in

place. Be sure to place bracket edge flush

against back of inner sill.

NOTE

L Bracket

Outer Sill

Inner Sill

Center Line

Screws

(Type A)

4

Open the window and draw a center line on

the center of the inner sill.

Then mark lines 7.5" (191mm) to the left and

right of the center line.

Room Side

Inner Sill

Center Line

Upper Guide

Screws (Type A)

Curtain

Screws

(Type A)

Screws

(Type A)

Left Curtain Panel

1

Align holes between the upper guide

and the top of the cabinet and then install it

with 3 type A screws

2

Insert the top and bottom rails of the curtain

panels into the upper and lower panel guides

Fasten the curtain panels to the unit with

8 type A screws Fasten screws behind the

curtain panel.

Use a long screwdriver to make installing

the screws easier.

NOTE

Right Curtain PanelRight Curtain Panel

Bottom Guide

3

Cut the window sash seals (Foam-PE)

to the proper length. Peel off the backing

and attach the adhesive-backed foam to

the underside of the window sash and the

bottom of the window frame.

Foam-PE

(Adhesive backed)

Preparation of Chassis

12

INSTALLATION

7.5"

(191mm)

7.5″

(191mm)

7.5″

(191mm)

●

NOTE

See the Electrical Data section for information

on attaching the power cord to an electrical

outlet.

1

Set the air conditioner in the window so that

is centered. Place the air conditioner so that

front edge of the bottom guide is against the

back edge of the sill.

Bring the window down so that the front edge

of the upper guide is in front of the window.

Make sure that air conditioner is level or

tilting slightly to the outside.

2

Extend the guide panels to fill the window

opening and use 2 type B screws and 2

type C screws to secure them

to the window.

CAUTION

During the following step, hold unit firmly until

window sash is lowered to top channel behind

side panel frames. Personal injury or property

damage may result if unit falls from window.

About

¼"

3

Cut the non-adhesive foam strip to the

proper length and insert it between the

upper window sash and the lower window

sash.

4

L bracket

Screw

(Type A)

Screw

(Type A)

To prevent broken glass or damage to

windows, on vinyl or other similarly

constructed windows, attach the L bracket

with a type A screw.

Vinyl

Wood

Unit Installation

13 EN

INSTALLATION

●

Window Frame

Upper Guide

L Bracket

Bottom Guide

Foam Strip

(Non-adhesive)

Screws

(Type B)

ScrewsScrews

(Type C)

(6.35mm)

14

OPERATION

Control Panel and Remote Control

Remote Control

1

4

2

5

3

1

Power

Press to turn the air conditioner ON or OFF.

2

Fan Speed

Press to set the fan speed to Low (F1),

Medium (F2), or High (F3).

3

Delay ON/OFF Timer

Delay ON - When the air conditioner is off,

set it to automatically turn on from 1 to 24

hours later, at its previous mode and fan

settings.

Delay OFF - When the air conditioner is on,

set it to automatically turn off from 1 to 24

hours later.

NOTE

●Each press of the Timer button advances

the timer by 1 hour. After the last press

the display returns to the temperature

setting.

4

Operation Mode

Press the Mode button to cycle between

4 types of air conditioner operation:

Energy Saver / Cool / Fan / Dry.

Cool

Fan - In this mode the fan circulates air

but the compressor does not run. Use

the Fan Speed button to set fan speed to

High, Medium or Low. In this mode, you

cannot adjust the set temperature.

Dry - This mode is ideal for rainy and

damp days to dehumidify the room rather

than cooling it significantly. Humidity is

removed from the room by the combination

of compressor operation and the fan speed

fixed at Low. The compressor and fan turn

off once the set temperature is reached.

Fan speed cannot be adjusted in Dry mode.

- This mode is ideal on hot days to

cool and dehumidify the room quickly. Use

the Temp

buttons to set the desired

room temperature and use the Fan Speed

button to set the desired fan circulation

speed.

Energy Saver - In this mode the

compressor and fan turn off when the set

temperature is achieved. Approximately

every 3 minutes the fan turns on to allow

the unit sensor to accurately determine if

more cooling is needed.

4 3 2

1

7

6

5

15 EN

OPERATION

5

Temperature Control

The thermostat monitors room temperature

to maintain the desired temperature. The

thermostat can be set between 60 °F–86 °F

(16 °C–30 °C). Press

or arrows to

increase or decrease temperature setting.

6

Remote Control Sensor

Clean Filter

The Clean Filter LED lights up to notify you

that the filter needs to be cleaned. After

cleaning the filter, press

Temp

and

together on the control panel to turn off the

Clean Filter light.

NOTE

●The filter reset must be done using the

control panel, not the remote control.

●This feature is a reminder to clean the air

filter for more efficient operation. The LED

light turns on after 250 hours of operation.

7

NOTE

●Auto Restart: If the air conditioner turns off due

to a power outage, it will restart automatically

once the power is restored, with the same

settings as were set before the unit turned off.

●Energy Saver: The unit defaults to the Energy

Saver mode each time the unit is switched on

except in Fan mode or when power is restored

after an electrical power outage.

●The remote control will not function properly if

the AC infrared sensor is exposed to direct light

or if there are obstacles between the remote

controller and the air conditioner

.

Wireless Remote Control

Inserting Batteries

1

Push out the cover on the back of the

remote control with your thumb.

2

With the plus and minus poles facing as

marked, and insert two new AAA 1.5 V

batteries.

3

Reattach the cover.

NOTE

●Two new batteries are supplied with the air

conditioner for use in the remote control.

●Do not use a rechargeable battery. Make sure

that the battery is new.

●In order to prevent discharge, remove the

battery from the remote control if the air

conditioner is not going to be used for an

extended period of time.

●Keep the remote control away from extremely

hot or humid places.

●To maintain optimal operation of the remote

control, the remote sensor should not be

exposed to direct sunlight.

16

OPERATION

Air Direction

Adjusting the air direction using the horizontal

air deflector control.

Using the control tabs, the air flow can be

directed to the left, right, straight ahead, or any

combination of these directions.

Additional Features

Slinger Fan

This air conditioner is equipped with a slinger

fan. (See drawing.)

The fan’s outer ring picks up the condensed

water from the base pan if the water level gets

high enough. The water is then picked up by the

fan and expelled through the condenser, making

the air conditioner more efficient.

Ring

17 EN

MAINTENANCE

2

Wash the filter using lukewarm water below

40 °C (104 °F).

Remove the air filter from the front grille by

pulling the filter forward and then up slightly.

3

Gently shake the excess water from the

filter and replace.

Cleaning the Air Conditioner

●Wipe the front grille and inlet grille with a cloth

dampened in a mild detergent solution.

●Wash the cabinet with mild soap or detergent

and lukewarm water, then polish using liquid

appliance wax.

NOTE

●

To ensure continued peak efficiency, the

condenser coils (outside of unit) should be

checked periodically and cleaned if clogged

with soot or dirt from outside air.

●For repair and maintenance, contact an

Authorized Service Center. See the warranty

page for details or call 1-888-LG-CANADA

(542 2623).

Have your model number and serial number

available. They should be written on page 22

of this manual.

MAINTENANCE

WARNING

Before cleaning or performing maintenance,

disconnect the power supply and wait until

the fan stops.

Air Filter

Check the air filter at least twice a month to see

if cleaning is necessary. Trapped particles in the

filter can build up and block the airflow, reducing

cooling capacity and causing an accumulation of

frost on the evaporator.

Cleaning the Air Filter

1

18

TROUBLESHOOTING

Before Calling for Service

The appliance is equipped with an automatic error-monitoring system to detect and diagnose problems

at an early stage. If the appliance does not function properly or does not function at all, check the

following before you call for service.

Normal Sounds You May Hear

1

High Pitched Chatter

2

Sound of Rushing Air

At the front of the unit, you may hear the sound of rushing air being moved by the fan.

Today's high efficiency compressors may have a high pitched chatter during the cooling cycle.

3

Gurgle/Hiss

Gurgling or hissing noise may be heard due to refrigerant passing through evaporator during

normal operation.

4

Vibration

Unit may vibrate and make noise because of poor wall or window construction or incorrect

installation.

5

Pinging or Swishing

Droplets of water hitting condenser during normal operation may cause pinging or swishing

sounds.

1

2

3

5

4

19

TROUBLESHOOTING

Problem Possible Cause Solutions

Air conditioner

does not start.

The air conditioner is unplugged.

Make sure the air conditioner plug

is pushed completely into the outlet.

The fuse is blown/circuit breaker

is tripped.

Check the house fuse/circuit

breaker box and replace the fuse or

reset the breaker.

Power failure.

If power failure occurs, turn the

mode control to off. When power is

restored, wait 3 minutes to restart

the air conditioner to prevent

tripping of the compressor overload.

The current interrupter device is

tripped.

Press the RESET button located

on the power cord plug. If the

RESET button will not stay

engaged, discontinue use of the air

conditioner and contact a qualified

service technician.

Air conditioner

does not cool as it

should.

Make sure there are no curtains,

blinds, or furniture blocking the front

of the air conditioner.

The temp control may not be set

Airflow is restricted.

The air filter is dirty.

correctly.

Set the desired temperature to

a level lower than the current

temperature.

weeks. See the 'MAINTENANCE'

Clean the filter at least every 2

section.

The room may have been hot.

When the air conditioner is first

on, you need to allow time

for the room to cool down.

Cold air is escaping.

Check for open fumace floor

registers and cold air returns.

Cooling coils have iced up.

See 'Air conditioner freezing up'

below.

Air conditioner

freezing up.

The cooling coils are iced over.

Ice may block the air flow and

obstruct the air conditioner from

properly cooling the room. Set the

mode control at High Fan or High

Cool.

Water drips

outside.

Hot, humid weather. This is normal.

EN

20

TROUBLESHOOTING

Problem Possible Cause Solutions

Water drips

indoors.

The air conditioner is not tilted to

the outside.

For proper water disposal, make

sure the air conditioner slants

slightly from the cabinet front to the

rear.

Water collects in

base pan.

Moisture removed from air and

drains into base pan.

Dirty air filter - air restricted.

This is normal for a short period in

areas with little humidity; normal for

a longer period in very humid areas.

Air conditioner

turns on and off

rapidly.

Outside temperature extremely

hot.

Refer to installation instructions or

Clean air filter.

check with installer.

Noise when unit is

cooling.

Air movement sound.

This is normal. If too loud, set to

lower FAN setting.

Window vibration - poor

installation.

Refer to installation instructions or

check with installer.

Remote sensing

deactivating

prematurely.

Remote control not located

within range.

Place remote control within 20 feet

& 120° radius of the front of the

unit.

Remote control signal

obstructed.

Set temperature too low.

Remove obstruction.

Room too cold. Increase set temperature.

NOTE

●If you see "CH" in the display, please call 1-888-LG-CANADA(542 2623).

La page charge ...

LG LW6017R Le manuel du propriétaire

LG LW6017R Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents