Empire Heating Systems Direct Vent Wall Furnace Heating System Le manuel du propriétaire

Marque: Empire Heating Systems

Modèle: Direct Vent Wall Furnace Heating System

Taper: Le manuel du propriétaire

Ce manuel convient également à

This appliance may be installed in an after-

market, permanently located, manufactured

home (USA only), or mobile home, where not

prohibited by state or local codes.

This appliance is only for use with the type

of gas indicated on the rating plate. This

appliance is not convertible for use with other

gases, unless a certied kit is used.

WARNING

FIRE OR EXPLOSION HAZARD

If the information in these instructions is

not followed exactly, a re or explosion may

result causing property damage, personal

injury or loss of life.

— Do not store or use gasoline or other

ammable vapors and liquids in the

vicinity of this or any other appliance.

— WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch;

do not use any phone in your building.

• Leave the building immediately.

• Immediately call your gas supplier

from a neighbor’s phone. Follow

the gas supplier’s instructions.

• If you cannot reach your gas

supplier, call the re department.

— Installation and service must be

performed by a qualied installer,

service agency or the gas supplier.

INSTALLER:

Leave this manual with the appliance.

CONSUMER:

Retain this manual for future reference.

WARNING

If not installed, operated and maintained in

accordance with the manufacturer's instruc-

tions, this product could expose you to sub-

stances in fuel or from fuel combustion which

can cause death or serious illness.

DIRECT

VENT WALL

FURNACE MODELS:

DV210SGXLP-2 DV215SGXLP-2

DV210SGXNAT-2 DV215SGXNAT-2

GAS-FIRED

INSTALLATION INSTRUCTIONS

AND OWNER'S MANUAL

Page 1

40946-0-1019Page 2

TABLE OF CONTENTS

Important Safety Information ......................................................................................................... 3

Safety Information for Users of Propane Gas ............................................................................... 4

Requirements for Massachusetts ................................................................................................. 5

Introduction ................................................................................................................................... 6

Specications ................................................................................................................................ 6

Gas Supply ................................................................................................................................... 7

Clearances ................................................................................................................................... 8

Installation Instructions .............................................................................................................. 8-9

Lighting Instructions ................................................................................................................... 10

Maintenance ............................................................................................................................... 12

Pilot Flame Characteristics ........................................................................................................ 13

Main Burner Flame Characteristics ............................................................................................ 13

Troubleshooting .......................................................................................................................... 13

Parts List .................................................................................................................................... 14

Parts View ................................................................................................................................... 15

Optional Blower Installation Instructions ............................................................................... 16-17

Master Parts Distributor List ........................................................................................................ 18

How to Order Repair Parts .......................................................................................................... 18

Warranty ...................................................................................................................................... 19

SECTION PAGE

40946-0-1019 Page 3

• Due to high temperatures the appliance should be

located out of trafc and away from furniture and

draperies.

• Children and adults should be alerted to the hazards

of high surface temperatures and should stay away

to avoid burns or clothing ignition.

• Young children should be carefully supervised when

they are in the same room as the appliance.

• Clothing or other ammable material should not be

placed on or near the appliance.

• Any safety screen or guard removed for servicing

an appliance must be replaced prior to operating the

appliance.

• Keep burner and control compartment clean.

• Vent cap hot while furnace is in operation.

• Installation and repair should be done by a QUALI-

FIED SERVICE PERSON. The appliance should

be inspected before use and at least annually by a

qualied service person.

• More frequent cleaning may be required due to ex-

cessive lint from carpeting, bedding materials, etc.

It is imperative that control compartments, burners,

and circulating air passageways of the appliance be

kept clean.

• DO NOT put anything around the furnace that will

obstruct the ow of combustion and ventilation air.

• DO keep the appliance area clear and free from

combustible material, gasoline, and other ammable

vapors and liquids.

• DO examine venting system periodically and replace

damaged parts.

• DO examine burners periodically. Clean and replace

damaged parts.

• CAUTION: Pilot hole cover must be kept tightly closed

during operation.

• DO NOT use this heater if any part has been under

water. Immediately call a qualied service technician

to inspect the heater and to replace any part of the

control system and any gas control which has been

under water.

THIS IS A HEATING APPLIANCE

DO NOT OPERATE THIS APPLIANCE WITHOUT FRONT PANEL INSTALLED.

IMPORTANT SAFETY INFORMATION

40946-0-1019Page 4

SAFETY INFORMATION FOR USERS OF PROPANE GAS

Propane is a ammable gas which can cause res and

explosions. In its natural state, propane is odorless and

colorless. You may not know all the following safety precautions

which can protect both you and your family from an accident.

Read them carefully now, then review them point by point with

the members of your household. Someday when there may not

be a minute to lose, everyone's safety will depend on knowing

exactly what to do. If, after reading the following information,

you feel you still need more information, please contact your

gas supplier.

PROPANE GAS WARNING ODOR

If a gas leak happens, you should be able to smell

the gas because of the odorant put in the Propane Gas.

That's your signal to go into immediate action!

• Do not operate electric switches, light matches, use your phone.

Do not do anything that could ignite the gas.

• Get everyone out of the building, vehicle, trailer, or area. Do

that IMMEDIATELY.

• Close all gas tank or cylinder supply valves.

• Propane Gas is heavier than air and may settle in low areas

such as basements. When you have reason to suspect a gas

leak, keep out of basements and other low areas. Stay out

until reghters declare them to be safe.

• Use your neighbor's phone and call a trained Propane Gas

service person and the re department. Even though you may

not continue to smell gas, do not turn on the gas again. Do not

re-enter the building, vehicle, trailer, or area.

• Finally, let the service man and reghters check for escaped

gas. Have them air out the area before you return. Properly

trained Propane Gas service people should repair the leak,

then check and relight the gas appliance for you.

NO ODOR DETECTED - ODOR FADE

Some people cannot smell well. Some people cannot smell the

odor of the chemical put into the gas. You must nd out if you can

smell the odorant in propane. Smoking can decrease your ability to

smell. Being around an odor for a time can affect your sensitivity or

ability to detect that odor. Sometimes other odors in the area mask

the gas odor. People may not smell the gas odor or their minds are

on something else. Thinking about smelling a gas odor can make

it easier to smell.

The odorant in Propane Gas is colorless, and it can fade under some

circumstances. For example, if there is an underground leak, the

movement of the gas through soil can lter the odorant. Odorants

in Propane Gas also are subject to oxidation. This fading can occur

if there is rust inside the storage tank or in iron gas pipes.

The odorant in escaped gas can adsorb or absorb onto or into

walls, masonry and other materials and fabrics in a room. That will

take some of the odorant out of the gas, reducing its odor intensity.

Propane Gas may stratify in a closed area, and the odor intensity

could vary at different levels. Since it is heavier than air, there may

be more odor at lower levels. Always be sensitive to the slightest gas

odor. If you detect any odor, treat it as a serious leak. Immediately

go into action as instructed earlier.

SOME POINTS TO REMEMBER

• Learn to recognize the odor of Propane Gas. Your local Propane

Gas Dealer can give you a "Scratch and Sniff" pamphlet. Use

it to nd out what the propane odor smells like. If you suspect

that your Propane Gas has a weak or abnormal odor, call your

Propane Gas Dealer.

• If you are not qualied, do not light pilot lights, perform service,

or make adjustments to appliances on the Propane Gas system.

If you are qualied, consciously think about the odor of Propane

Gas prior to and while lighting pilot lights or performing service

or making adjustments.

• Sometimes a basement or a closed-up house has a musty

smell that can cover up the Propane Gas odor. Do not try to

light pilot lights, perform service, or make adjustments in an

area where the conditions are such that you may not detect

the odor if there has been a leak of Propane Gas.

• Odor fade, due to oxidation by rust or adsorption on walls of

new cylinders and tanks, is possible. Therefore, people should

be particularly alert and careful when new tanks or cylinders

are placed in service. Odor fade can occur in new tanks, or

reinstalled old tanks, if they are lled and allowed to set too

long before relling. Cylinders and tanks which have been out

of service for a time may develop internal rust which will cause

odor fade. If such conditions are suspected to exist, a periodic

sniff test of the gas is advisable. If you have any question about

the gas odor, call your Propane Gas Dealer. A periodic sniff

test of the Propane Gas is a good safety measure under any

condition.

• If, at any time, you do not smell the Propane Gas odorant and

you think you should, assume you have a leak. Then take the

same immediate action recommended above for the occasion

when you do detect the odorized Propane Gas.

• If you experience a complete "gas out," (the container is under

no vapor pressure), turn the tank valve off immediately. If the

container valve is left on, the container may draw in some air

through openings such as pilot light orices. If this occurs, some

new internal rusting could occur. If the valve is left open, then

treat the container as a new tank. Always be sure your con-

tainer is under vapor pressure by turning it off at the container

before it goes completely empty or having it relled before it is

completely empty.

40946-0-1019 Page 5

REQUIREMENTS FOR MASSACHUSETTS

For all side wall horizontally vented gas fueled equipment installed

in every dwelling, building or structure used in whole or in part for

residential purposes, including those owned or operated by the

Commonwealth and where the side wall exhaust vent termination

is less than seven (7) feet above nished grade in the area of the

venting, including but not limited to decks and porches, the following

requirements shall be satised:

1. INSTALLATION OF CARBON MONOXIDE DETECTORS. At

the time of installation of the side wall horizontal vented gas fu-

eled equipment, the installing plumber or gastter shall observe

that a hard wired carbon monoxide detector with an alarm and

battery back-up is installed on the oor level where the gas

equipment is to be installed. In addition, the installing plumber

or gastter shall observe that a battery operated or hard wired

carbon monoxide detector with an alarm is installed on each

additional level of the dwelling, building or structure served by

the side wall horizontal vented gas fueled equipment. It shall be

the responsibility of the property owner to secure the services

of qualied licensed professionals for the installation of hard

wired carbon monoxide detectors.

a. In the event that the side wall horizontally vented gas fu-

eled equipment is installed in a crawl space or an attic,

the hard wired carbon monoxide detector with alarm and

battery back-up may be installed on the next adjacent oor

level.

b. In the event that the requirements of this subdivision can not

be met at the time of completion of installation, the owner

shall have a period of thirty (30) days to comply with the

above requirements; provided, however, that during said

thirty (30) day period, a battery operated carbon monoxide

detector with an alarm shall be installed.

2. APPROVED CARBON MONOXIDE DETECTORS. Each carbon

monoxide detector as required in accordance with the above

provisions shall comply with NFPA 720 and be ANSI/UL 2034

listed and IAS certied.

3. SIGNAGE. A metal or plastic identication plate shall be per-

manently mounted to the exterior of the building at a minimum

height of eight (8) feet above grade directly in line with the

exhaust vent terminal for the horizontally vented gas fueled

heating appliance or equipment. The sign shall read, in print

size no less than one-half (1/2) inch in size, “GAS VENT DI-

RECTLY BELOW. KEEP CLEAR OF ALL OBSTRUCTIONS”.

4. INSPECTION. The state or local gas inspector of the side wall

horizontally vented gas fueled equipment shall not approve the

installation unless, upon inspection, the inspector observes

carbon monoxide detectors and signage installed in accordance

with the provisions of 248 CMR 5.08(2)(a) 1 through 4.

(b) EXEMPTIONS: The following equipment is exempt from

248 CMR 5.08(2)(a)1 through 4:

1. The equipment listed in Chapter 10 entitled “Equip-

ment Not Required To Be Vented” in the most current

edition of NFPA 54 as adopted by the Board; and

2. Product Approved side wall horizontally vented gas

fueled equipment installed in a room or structure

separate from the dwelling, building or structure used

in whole or in part for residential purposes.

VENTING SYSTEM PROVIDED. When the manufacturer of

Product Approved side wall horizontally vented gas equip-

ment provides a venting system design or venting system

components with the equipment, the instructions provided

by the manufacturer for installation of the equipment and

the venting system shall include:

1. Detailed instructions for the installation of the venting

system design or the venting system components; and

2. A complete parts list for the venting system design or

venting system.

(e) A copy of all installation instructions for all Product Approved

side wall horizontally vented gas fueled equipment, all

venting instructions, all parts lists for venting instructions,

and/or all venting design instructions shall remain with the

appliance or equipment at the completion of the installation.

40946-0-1019Page 6

INTRODUCTION

Introduction

Always consult your local Building Department regarding regulations,

codes or ordinances which apply to the installation of a direct vent

wall furnace.

Instructions to Installer

1. Installer must leave instruction manual with owner after

installation.

2. Installer must have owner ll out and mail warranty card supplied

with furnace.

3. Installer should show owner how to start and operate furnace.

WARNING

Any change to this furnace or its control can be dangerous.

This is a heating appliance and any panel, door or guard

removed for servicing an appliance must be replaced prior

to operating the appliance.

To Conserve Gas: Turn off pilot when heater is not in use.

General Information

This furnace is design certied in accordance with American National

Standard/CSA Standard Z21.86 and CSA 2.32 by the Canadian

Standards Association, as a Gravity Direct Vent Wall Furnace to be

installed on an outside wall according to these instructions.

Any alteration of the original design, installed other than as shown

in these instructions or use with a type of gas not shown on the

rating plate is the responsibility of the person and company making

the change.

Important

All correspondence should refer to complete Model No., Serial No.

and type of gas.

NOTICE: During initial ring of this unit, its paint will bake out and

smoke will occur. To prevent triggering of smoke alarms, ventilate

the room in which the unit is installed.

Installation in Residential Garages

Gas utilization equipment in residential garages shall be installed

so that all burners and burner ignition devices are located not less

than 18" (457mm) above the oor.

Such equipment shall be located, or protected, so it is not subject

to physical damage by a moving vehicle.

Qualied Installing Agency

Installation and replacement of gas piping, gas utilization equipment

or accessories and repair and servicing of equipment shall be

performed only by a qualied agency. The term "qualied agency"

means any individual, rm, corporation or company which either in

person or through a representative is engaged in and is responsible for

(a) the installation or replacement of gas piping or (b) the connection,

installation, repair or servicing of equipment, who is experienced in

such work, familiar with all precautions required and has complied

with all the requirements of the authority having jurisdiction.

Commonwealth of Massachusetts: The installation must be

made by a licensed plumber or gas tter in the Commonwealth

of Massachusetts.

The installation must conform with local codes or, in the absence of

local codes, with the National Fuel Gas Code ANSI Z223.1/NFPA

54* Natural Gas and Propane Installation Code, CSA B149.1.

*Available from the American National Standards Institute, Inc., 11

West 42nd St., New York, N.Y. 10036.

High Altitudes

For altitudes/elevations above 2,000 feet (610m) , input ratings

should be reduced at the rate of 4 percent for each 1,000 feet (305m)

above sea level. Canadian High Altitudes for locations having an

elevation above mean sea level between 2,000 feet (610m) and

4,500 feet (1370m), the manifold pressure is to be decreased from

4.0" w.c. (.996kPa) to 3.2" w.c. (.797kPa) for Natural Gas and from

10.0" w.c. (2.49kPa) to 8.0" w.c. (1.99kPa) for Propane Gas.

Installation on Rugs and Tile

If this appliance is to be installed directly on carpeting, tile, or other

combustible material, other than wood ooring, the appliance shall

be installed on a metal or wood panel extending the full width and

depth of the appliance.

The base referred to above does not mean the re-proof base as

used on wood stoves. The protection is primarily for rugs that may

be extremely thick and light-color tile that may discolor.

Well Head Gas Installations

Some Natural Gas utilities use "well head" gas. This may affect

the BTU output of the unit and promote sooting. Units shall not be

converted to use well head gas.

This appliance is only for use with the type of gas indicated on the

rating plate. This appliance is not convertible for use with other gases.

40946-0-1019 Page 7

SPECIFICATIONS

INTRODUCTION (CONT'D)

Model DV-210 DV-215

Input BTU/HR (KW/H) 10,000 (2.9) 15,000 (4.4)

Height 21 3/8" (543mm) 24 7/8" (632mm)

Width 16 1/4 (413mm) 20 1/4" (514mm)

Depth 9 3/8" (239mm) 9 3/8" (239mm)

Gas Inlet 1/2" (13mm) 1/2" (13mm)

OPTIONS FOR ABOVE FURNACES

Blower DVB-1 DVB-1

VINYL SIDING VENT KITS

Description Model Number

Vinyl Siding Vent Kit DV822 DV822

Vinyl Siding Vent Kit VSK1 VSK1

VENT EXTENSION KITS

Part Number Description Used On

TH358

Vent Extension Kit For Propane

Units (13"-19" Walls)

DV215SGXLP-1,2

TH357

Vent Extension Kit For Natural

Units (13"-19" Walls)

DV215SGXNAT-1,2

TH345 & TH346 Vent Extension (13"-19" Walls) DV210SGXNAT-2 DV210SGXLP-2

CONVERSION KITS

Part Number Description Used On

17081 Propane to Natural DV210SGXLP

17080 Natural to Propane DV210SGXNAT

17083 Propane to Natural DV215SGXLP

17082 Natural to Propane DV215SGXNAT

When an existing Category 1 heater is removed or replaced, the

original venting system may no longer be sized to properly vent the

attached appliances. Instructions shall also indicate effects of an

improperly sized venting system (formation of condensate, leakage,

spillage, etc.) and shall specify the following test procedure:

WARNING

CARBON MONOXIDE POISONING HAZARD

Failure to follow the steps outlined below for each appliance

connected to the venting system being placed into operation

could result in carbon monoxide poisoning or death.

The following steps shall be followed for each appliance

connected to the venting system being placed into

operation, while all other appliances connected to the

venting system are not in operation:

1. Seal any unused openings in the venting system.

2. Inspect the venting system for proper size and

horizontal pitch, as required in the National Fuel Gas

Code, ANSI Z223.1/NFPA 54 or the Natural Gas and

Propane Installation Code, CSA B149.1 and these

instructions. Determine that there is no blockage or

restriction, leakage, corrosion and other deciencies

which could cause an unsafe condition.

3. As far as practical, close all building doors and

windows and all doors between the space in which

the appliance(s) connected to the venting system are

located and other spaces of the building.

4. Close replace dampers.

5. Turn on clothes dryers and any appliance not connected

to the venting system. Turn on any exhaust fans, such

as range hoods and bathroom exhausts, so they are

operating at maximum speed. Do operate a summer

exhaust fan.

6. Follow the lighting instructions. Place the appliance

being inspected into operation. Adjust the thermostat

so appliance is operating continuously.

7. Test for spillage from draft hood equipped appliances

at the draft hood relief opening after 5 minutes of main

burner operation. Use the ame of a match or candle.

8. If improper venting is observed during any of the

above tests, the venting system must be corrected in

accordance with National Fuel Gas Code, ANSI Z223.1/

NFPA 54 and/or Natural Gas and Propane Installation

Code, CSA B149.1.

9. After is has been determined that each appliance

connected

to the venting system properly vents when

tested as outlined above, return doors, windows,

exhaust fans, replace dampers and any other gas-red

burning appliance to their previous conditions of use.

40946-0-1019Page 8

GAS SUPPLY

Locating Gas Supply

The gas line can enter the unit either through the oor or outside

wall. The gas line opening should be made at this time. Location

of the opening will be determined by the position of oor joists and

the valve and union used for servicing.

RECOMMENDED GAS PIPE DIAMETER

Pipe

Length

Schedule 40 Pipe

Inside Diameter

Tubing, Type L

Outside Diameter

Natural Propane Natural Propane

0-10 feet

0-3 meters

1/2”

12.7 mm

3/8”

9.5mm

1/2”

12.7 mm

3/8”

9.5 mm

10-40 feet

4-12 meters

1/2”

12.7 mm

1/2”

12.7mm

5/8”

15.9 mm

1/2”

12.7 mm

40-100 feet

13-30 meters

1/2”

12.7 mm

1/2”

12.7mm

3/4”

19 mm

1/2”

12.7 mm

100-150 feet

31-46 meters

3/4”

19 mm

1/2”

12.7 mm

7/8”

22.2 mm

3/4”

19 mm

NOTE: Never use plastic pipe. Check to conrm whether your local

codes allow copper tubing or galvanized.

NOTE: Since some municipalities have additional local codes, it

is always best to consult your local authority and installation code.

The use of the following gas connectors is recommended:

— ANS Z21.24 Appliance Connectors of Corrugated Metal Tubing

and Fittings

— ANS Z21.45 Assembled Flexible Appliance Connectors of Other

Than All-Metal Construction

The above connectors may be used if acceptable by the authority

having jurisdiction. The Commonwealth of Massachusetts requires

that a exible appliance connector cannot exceed three feet in length.

NPT NIPPLE

Figure 1

Consult the current National Fuel Gas Code, ANSI Z223.1 CAN/

CGA-B149 (.1 or .2) installation code.

Installing a New Main Gas Shut-Off

Each appliance should have its own manual gas shut-off.

A manual main gas shut-off should be located in the vicinity of the

unit. Where none exists, or where its size or location is not adequate,

contact your local authorized installer for installation or relocation.

Compounds used on threaded joints of gas piping shall be resistant

to the action of liqueed petroleum gases. The gas lines must be

checked for leaks by the installer. This should be done with a soap

solution watching for bubbles on all exposed connections, and if

unexposed, a pressure test should be made.

Never use an exposed ame to check for leaks. Appliance must be

disconnected from piping at inlet of control valve and pipe capped

or plugged for pressure test. Never pressure test with appliance

connected; control valve will sustain damage!

A gas valve and ground joint union should be installed in the gas

line upstream of the gas control to aid in servicing. It is required by

the National Fuel Gas Code that a drip line be installed near the gas

inlet. This should consist of a vertical length of pipe tee connected

into the gas line that is capped on the bottom in which condensation

and foreign particles may collect.

Figure 2

Method of Installing a Tee Fitting Sediment Trap

Pressure Testing of the Gas Supply System

1. To check the inlet pressure to the gas valve, a 1/8" (3mm) N.P.T.

plugged tapping, accessible for test gauge connection, must be

placed immediately upstream of the gas supply connection to

the appliance.

2. The appliance and its individual shut-off valve must be

disconnected from the gas supply piping system during any

pressure testing of that system at test pressures in excess of

1/2 psig (3.5 kPa).

3. The appliance must be isolated from the gas supply piping system

by closing its individual manual shut-off valve during any pressure

testing of the gas supply piping system at test pressures equal

to or less than 1/2 psig (3.5 kPa).

Attention! If one of the above procedures results in pressures

in excess of 1/2 psig (14" w.c.) (3.5 kPa) on the appliance gas

valve, it will result in a hazardous condition.

Checking Manifold Pressure

Both Propane and Natural Gas valves have a built-in pressure

regulator in the gas valve. Natural Gas models will have a manifold

pressure of approximately 4.0" w.c. (.996kPa) at the valve outlet

with the inlet pressure to the valve from a minimum of 5.0" w.c.

(1.245kPa) for the purpose of input adjustment to a maximum of

10.5" w.c. (2.61kPa). Propane Gas models will have a manifold

pressure approximately 10.0" w.c. (2.49kPa) at the valve outlet

with the inlet pressure to the valve from a minimum of 11.0" w.c.

(2.739kPa) for the purpose of input adjustment to a maximum of

13.0" w.c. (3.237kPa).

A 1/8" (3mm) N.P.T. plugged tapping, accessible for test gauge

connection, is located on the outlet side of the gas control.

40946-0-1019 Page 9

CLEARANCES

The furnace is to be located on an outside wall. Locate wall studs so

that wall opening will be located between wall studs. One wall stud

can be used for attachment of inside wall plate. The wall opening

required as shown in Figure 3 is a minimum diameter of 6 1/4

(159mm) inches. The inside wall plate and the outside wall plate are

large enough to permit a wall opening diameter of 8 inches (203mm).

A template is provided in furnace carton for positioning furnace on

the wall. Also, refer to Figure 3 for positioning the furnace on wall

and for locating gas line connection.

Figure 3

Installing Inside Wall Plate

After the wall opening has been located and cut, center and level

inside wall plate in wall opening. The collar on the inside wall plate

is to be placed within the wall opening. If there is insulation above

the wall opening (air inlet tube) a barrier should be installed above

the wall opening (air inlet tube) to prevent insulation from coming in

contact with the air inlet tube. The barrier must not penetrate into the

6-1/4" (159mm) diameter wall opening. On solid wall or wall stud,

attach inside wall plate with (6) #10 x 1 1/2" (38mm) screws provided.

On sheet rock wall, by using wall opening for access, attach inside

wall plate with (6) #10 x 1 1/2" (38mm) screws and (6) Tinnerman

nuts provided.

Attaching Furnace To Inside Wall Plate

Align and attach mounting clips on furnace back with mounting slots

on inside wall plate. The furnace support bracket located at furnace

bottom is to be secured to wall. On solid wall, secure furnace support

bracket with (1) #10 x 1 1/2" (38mm) screw provided. On sheet rock

wall, secure furnace support bracket with (1) toggle bolt provided.

(64mm)

(13mm)

Figure 4

INSTALLATION INSTRUCTIONS

1. In selecting a location for installation, it is necessary to provide

adequate accessibility clearances for servicing and proper

installation.

2. Although certied for 0 clearance to the oor , the unit is held in

place by a wall bracket. Enough clearance [2" (51mm) suggested]

to allow changing or adding oor covering is recommended.

Other clearances to combustible construction:

Sides 1" (25mm) and 12" (305mm) from the top.

3. Note the position of the vent relative to the center of the unit.

The DV-210 has the vent in the center. The DV-215 vent is 2"

(51mm) off center to the right.

4. The minimum distance from the center of the outside vent to

the nearest outside corner or obstruction is 16" (406mm).

5. The DV-210/DV-215 minimum wall depth is 4 1/2" (114mm)

and maximum wall depth is 13" (330mm). The use of tubes not

supplied by the manufacturer result in unsatisfactory performance.

The vent terminal of a direct vent appliance, with an input of 10,000

Btu per hour (3 kW) or less shall be located at least 6" (150mm)

from any air opening into a building, and such an appliance with an

input over 10,000 Btu per hour (3 kW) but not over 50,000 Btu per

hour (14.7 kW) shall be installed with a 9" (229mm) vent terminal

clearance and the bottom of the vent terminal and the air intake

shall be located at least 12" (305mm) above grade.

CAUTION

The nearest point of the vent cap should be a minimum

horizontal distant of six (6) feet (1.8m) from any pressure

regulator. In case of regulator malfunction, the six feet (1.8m)

distance will reduce the chance of gas entering the vent cap.

The maximum wall depth may be extended to 19" (483mm) by us-

ing the vent extension kits listed on page 7.

40946-0-1019Page 10

INSTALLATION INSTRUCTIONS (CONT'D)

Cutting Vent Tubes

This is the most important part of the installation. With the furnace

installed on wall the 5" (127mm) diameter air inlet tube and 3"

(76mm) diameter ue outlet tube are to be marked and cut using

the following procedure.

1. Attach 5" (127mm) diameter air inlet tube onto the collar of air drop

assembly. Be sure 5" (127mm) diameter air inlet tube is placed

as far as possible onto the collar of the air drop assembly. Mark

the 5" (127mm) diameter air inlet tube 1/2" (13mm) beyond the

outside wall. Remove 5" (127mm) diameter air inlet tube from

collar of air drop assembly.

2. Attach 3" (76mm) diameter ue outlet tube onto ue outlet collar

on combustion chamber. Be sure 3" (76mm) diameter ue outlet

tube is placed as far as possible onto the collar of ue outlet.

Mark the 3" (76mm) diameter ue outlet tube 2" (51mm) beyond

the outside wall. Remove 3" (76mm) diameter ue outlet tube

from collar of ue outlet on combustion chamber.

3. Mark or wrap tape completely around the tubes at the marked

points to help in making a true cut. Do not crimp or enlarge tubes.

Installing The Vent Assembly

1. Place caulking (not provided) beneath the edge of the outside

wall plate. Use additional caulking to correct uneven wall surface,

such as clapboard.

2. Attach 5" (127mm) diameter air inlet tube onto the collar of air

drop assembly. Attach caulked, outside wall plate into the 5"

(127mm) diameter air inlet tube. Position the outside wall plate

so that 5" (127mm) diameter air inlet tube has a slight downward

slope to the outside. The downward slope is necessary to prevent

the entry of rainwater. Attach outside wall plate to exterior wall

with (4) #10 x 1 1/2" (38mm) screws provided.

3. Apply furnace cement to 3" (76mm) diameter ue outlet collar

on combustion chamber and to 3" (76mm) diameter collar on

vent cap. Attach 3" (76mm) diameter ue outlet tube onto ue

outlet collar on combustion chamber. Attach vent cap into the

3" (76mm) diameter ue outlet tube. Attach vent cap to outside

wall plate with (3) #10 x 1/2" (13mm) screws provided.

4. Installation is completed.

Reassembly And Resealing Vent-Air Intake System

When vent-air intake system is removed for servicing the furnace,

the following steps will assure proper reassembly and resealing of

the vent-air intake assembly.

1. Remove old furnace cement from ue outlet collar on combustion

chamber and collar of vent cap. Remove old furnace cement

from both ends of 3" (76mm) diameter ue outlet tube.

2. Remove old caulking beneath the edge of the outside wall plate.

Apply new caulking beneath the edge of the outside wall plate.

Use additional caulking to correct uneven wall surface, such as

clapboard.

3. Attach 5" (127mm) diameter air inlet tube onto the collar of air

drop assembly. Attach caulked, outside wall plate into the 5"

(127mm) diameter air inlet tube. Position the outside wall plate

so that 5" (127mm) diameter air inlet tube has a slight downward

slope to the outside. The downward slope is necessary to prevent

the entry of rainwater. Attach outside wall plate to exterior wall

with (4) #10 x 1" (25mm) screws provided.

4. Apply furnace cement to 3" (76mm) diameter ue outlet collar

on combustion chamber and to 3" (76mm) diameter collar on

vent cap. Attach 3" (76mm) diameter ue outlet tube onto ue

outlet collar on combustion chamber. Attach vent cap into the

3" (76mm) diameter ue outlet tube. Attach vent cap to outside

wall plate with (3) #10 x 1/2" (13mm) screws provided.

5. Reassembly and resealing vent-air intake system is completed.

Installing a Vent Near a Window Ledge, Other Type of Projection

or on Siding (vinyl, aluminum, etc.)

Direct vent furnaces are designed to be installed on a uniform

outside wall. When the wind comes from any angle (up, down or

from either side), it must hit the vent cap equally over both the air

inlet and the ue outlet portions of the vent. Any wall projection,

such as a door or window casing, which disturbs the wind on one

side of the air inlet section will result in back pressure on the ue

section smothering the ame and eventual pilot outage.

When the vent cap is to be installed on siding or it appears that a

projection within 6" (152mm) of any side of the air inlet section could

shield the air inlet section, the entire vent should be supported away

from the wall at least the distance of the projection. 2" x 4" (51mm

x 102mm) framing whose outside dimensions match the overall

dimensions of the mounting plate is recommended. The 2" x 4"

(51mm x 102mm) framing protects siding from possible warpage

or discoloration. All joints can then be sealed and painted. The wall

depth plus the additional depth of the 2" x 4" (51mm x 102mm)

framing should not exceed a total depth of 13" (330mm) for DV-210/

DV-215. See Figure 5.

(51mmx102mm)

Figure 5

Figure 5a

Vinyl siding vent kit, DV-822, is available from Empire Comfort Systems,

Inc. The depth is 3" (76mm), which enables the vent cap to be extended

away from siding or projections. The wall depth plus the additional 3"

(76mm) depth of the vinyl siding vent cap extension should not exceed

a total depth of 13" (330mm) for DV-210/DV-215. See Figure 5a.

WARNING

When vinyl siding vent kit, DV-822 or 2" x 4" (51mm x 102mm)

framing is added to an existing installation (furnace is

installed) do not attempt to add sections of pipe to the ue

outlet tube or air inlet tube. An air tight seal is required for

both tubes. Refer to Parts List, page 14 to order tubes.

40946-0-1019 Page 11

WARNING

If you do not follow these instructions exactly, a re or explosion may result causing property damage,

personal injury or loss of life.

1. STOP! Read the safety information above.

2. Turn off all electric power to the appliance

(if applicable).

3. Remove control access panel (front panel).

4. Push in gas control knob slightly and turn clockwise

to OFF.

NOTE: Knob cannot be turned from "PILOT" to "OFF"

unless knob is pushed in slightly. Do not force.

5. Wait ten (10) minutes to clear out any gas. Then

smell for gas, including near the oor. If you smell

gas, STOP! Follow "B" in the safety information above.

If you don't smell gas, go to the next step.

6. Remove the pilot access cover located on the

combustion chamber.

7. Find pilot - follow metal tube

from gas control. The pilot is

behind the pilot access cover.

8. Turn knob on gas control counterclockwise

to "PILOT."

9. Push in control knob all the way and hold in.

Immediately light the pilot with the Piezo Pilot Ignitor

or a match. Continue to hold the control knob in for

about one (1) minute after the pilot is lit. Release

knob, and it will pop back up. Pilot should remain

lit. If it goes out, repeat steps 5 through 10.

• If knob does not pop up when released,

stop and immediately call your service

technician or gas supplier.

• If the pilot will not stay lit after several tries,

turn the gas control knob to "OFF" and call

your service technician or gas supplier.

10. Replace pilot access cover.

11. Turn gas control knob counterclockwise

to "ON."

12. Replace control access panel (front panel).

13. Turn on all electric power to the appliance (if

applicable).

14. CAUTION: Pilot access cover must be kept tightly

closed during operation.

TO TURN OFF GAS TO APPLIANCE

FOR YOUR SAFETY READ BEFORE LIGHTING

A. This appliance has a pilot which must be lighted by

hand. When lighting the pilot, follow these instructions

exactly.

B. BEFORE LIGHTING smell all around the appliance area

for gas. Be sure to smell next to the oor because some

gas is heavier than air and will settle on the oor.

WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch;

do not use any phone in your building.

• Immediately call your gas supplier from a neighbor's

phone. Follow the gas supplier's instructions.

• If you cannot reach your gas supplier, call the

re department.

C. Use only your hand to push in or turn the gas control

knob. Never use tools. If the knob will not push in

or turn by hand, don't try to repair it; call a qualied

service technician. Force or attempted repair may

result in a re or explosion.

D. Do not use this appliance if any part has been under

water. Immediately call a qualied service technician

to inspect the appliance and to replace any part of

the control system and any gas control which has

been under water.

1. Turn off all electric power to appliance if service is to

be performed (if applicable).

2. Remove control access panel (front panel).

3. Push in gas control knob slightly and turn clock-

wise to "OFF." Do not force.

4. Replace control access panel (front panel).

LIGHTING INSTRUCTIONS

PILOT

BURNER

THERMOPILE

LIGHTING INSTRUCTIONS

GAS CONTROL

KNOB SHOWN

IN “OFF”

POSITION

40946-0-1019Page 12

These heaters are specially designed for use on self generating

systems. They should never be used on line or low voltage A.C.

circuits.

Installing the ON/OFF Device

To install an ON/OFF device (such as a wall switch, remote, toggle

switch,or thermostat), remove the wire nut from the two wires from

the valve. Run additional wire from the valve wires to the ON/OFF

device. Install the ON/OFF device in the same room as the furnace

following the installation instructions supplied with it. In the absence

of instructions, install the ON/OFF device 4 to 5 feet above the oor

on an interior wall not affected by another heating source (i.e. stove

or water heater) or the temperature of an adjoining room..

System Check

A millivolt meter is required to check the system. The millivolt

readings should be:

• Across the thermopile terminals, 400-450 millivolts with the

heater OFF.

• Across the thermopile terminals, 150-250 millivolts with the

heater ON.

• Across the wires at the valve, less than 30 millivolts with the

heater ON.

Steps in Removing Main Burner, Orice and Valve

1. Disconnect the thermopile and pilot supply line at the pilot burner.

2. Remove the burner compartment cover 5/16" (8mm) socket

suggested.

3. Remove screw holding left side of burner and lift out.

4. Main burner orice is now accessible. Use 1/2" (13mm) box end

wrench to remove and apply non-hardening pipe dope sparingly

to orice threads when replaced.

5. To remove the entire gas valve the nut holding the orice tting

to the chamber must be removed and the gas supply to the

valve disconnected. After this, the valve and orice elbow can

be removed as a unit.

Cleaning The Pilot Burner

Proper operation depends on a good pilot ame. The ame must

cover the top of the thermopile. Cleaning of the pilot may be an

annual necessity due to spiders. After removing the supply tubing

and orice, use a pipe cleaner or wire to clean the entire internal

part of the pilot.

Cleaning the Combustion Chamber and Main Burner

When the main burner and vent cap are removed, all internal areas of

the combustion chamber are accessible for cleaning with a vacuum

hose. The main burner may be cleaned by forcing water into the

ports and the throat of the burner. The burner should be blown dry

or heated to dry all water out before reinstalling.

Piezo Pilot Ignitor Instructions

Depressing the piezo ignitor button completely causes a spark to

occur at the pilot. This is a substitute for a match which requires

opening the pilot hole cover.

To light the pilot, it is important that the electrode be 1/8" (3 mm)

from the thermopile. The spark must occur at the point the burner

ame hits the thermopile. The end of the electrode will be red hot

with the pilot on.

On a new installation with air in the gas line, it is suggested that a

match be used. The match will light the pilot faster than the piezo

under this condition.

To Conserve Gas: Turn off pilot when heater is not in use.

TO ON/OFF DEVICE

Figure 6

MAINTENANCE

40946-0-1019 Page 13

The pilot ame is blue and goes toward the main burner and thermopile

horizontally. A slight yellow tip on the ame is normal. The pilot

ame must surround and extend approximately 1/4" (6mm) beyond

the thermopile, and must extend beyond the rst row toward the

second row of main burner ports.

THERMOPILE

PILOT

FLAME

PILOT ASSEMBLY

MAIN BURNER

CARRYOVER PORTS

Figure 7

PILOT FLAME CHARACTERISTICS

1. Lit match goes out as it enters lighter port.

a. Certain wind conditions will blow out match. Ignite

match, and as it ares, thrust match through opening.

b. Open nearby door or window and relight pilot.

2. Pilot ames but goes out when knob is released.

a. See Lighting Instructions. Relight Pilot.

b. Relight the pilot and hold knob down longer and harder.

Close lighter hole cover just after igniting. Check for a

good pilot ame.

c. Defective thermopile or defective magnet in safety section

of valve. Replace.

3. Yellow pilot ame.

a. Obstruction at pilot orice.

b. Clean and properly size orice.

4. Pilot and main burner go out during normal operation.

a. Check millivolts.

b. Check for proper size of pilot ame.

c. Check for defective or weak thermopile.

d. Check input, reduce as needed.

e. Cover on pilot lighter hole must be air tight.

f. Check for tight t of air and ue tubes at both ends of vent

assembly. No obstruction around vent that would prevent

the wind from hitting all of the vent equally.

5. Yellow main burner ame soot on the vent cap.

a. Remove main burner to check for obstructions in throat,

ports and orices.

b. Install new main burner orice and pilot orice. Refer to

Parts List on Page 14.

TROUBLESHOOTING

On the main burner, the burning gas forms a primary ame and a

secondary ame. The primary ame is blue and about 3/16" (5mm)

high. The secondary ame is very pale blue, 3 inches (76mm) to

5 inches (127mm) high. Dust in the combustion air will produce

an orange ame. Do not mistake it for an improper yellow ame.

PRIMARY FLAME

SECONDAR

Y FLAME

Figure 8

MAIN BURNER FLAME CHARACTERISTICS

40946-0-1019Page 14

USE ONLY MANUFACTURER'S REPLACEMENT PARTS. USE OF ANY OTHER PARTS COULD CAUSE INJURY OR DEATH.

PARTS LIST

Index

No.

Part

No.

Description

1 TH100 WALL MOUNTING PLATE

2 TH104 GASKET - FOR WALL MOUNTING PLATE

3 TH015 AIR DROP ASSEMBLY - DV210

3 TH018 AIR DROP ASSEMBLY - DV215

4 11757 OUTER CASING - DV210

4 11758 OUTER CASING - DV215

5 40968 INNER CASING - DV210

5 40969 INNER CASING - DV215

6 TH008 FRONT PANEL - DV210

6 TH009 FRONT PANEL - DV215

7 40960 COMBUSTION CHAMBER - DV210

7 40961 COMBUSTION CHAMBER - DV215

8 M155 GASKET - OBSERVATION HOLE COVER

9 DV781 OBSERVATION HOLE COVER

10 DV064 COVER PLATE - OBSERVATION HOLE

11 R206 NUT FOR ORIFICE FITTING

12 P8654 BURNER ORIFICE - DV210 NATURAL

12 P8650 BURNER ORIFICE - DV215 NATURAL

12 P8665 BURNER ORIFICE - DV210 PROPANE

12 P8658 BURNER ORIFICE - DV215 PROPANE

13 P104 ORIFICE FITTING

14 R1055 ELECTRODE AND WIRE

15 R12797 MANIFOLD

16 R12791 GAS VALVE 7000 MVRLC - NATURAL

16 R12792 GAS VALVE 7000 MVRLC - PROPANE

17 R12795

PILOT BURNER WITH ORIFICE - PROPANE

17 R12796 PILOT BURNER WITH ORIFICE - NATURAL

18 TH335 PILOT SHIELD

19 M151 GASKET - PILOT BURNER

20 TH133 CHAMBER DOOR WITH GASKET - DV210

20 TH134 CHAMBER DOOR WITH GASKET - DV215

21 40967 VALVE BRACKET

22 40994

PILOT TUBING - 1/8" (3.2mm) WITH

FERRELLS

23 R1054 THERMOPILE - GENERATOR

24 R2708 PIEZO IGNITOR

25 TH289 IGNITOR BRACKET

26 40956 BURNER - DV210

26 40957 BURNER - DV215

27 TH109 3" (76mm) DIA. FLUE OUTLET TUBE

28 TH107 5" (127mm) DIA AIR INLET TUBE

29 TH331 OUTSIDE MOUNTING PLATE

30 TH334 VENT CAP

31 TH123 VENT KIT COMPLETE

N/S R1081 ORIFICE FOR PILOT - NATURAL

N/S R1089 ORIFICE FOR PILOT - PROPANE

N/S TH300 GASKET FOR CHAMBER DOOR - DV210

N/S TH281 GASKET FOR CHAMBER DOOR - DV215

N/S TH351 HARDWARE PACKAGE

N/S - NOT SHOWN

Index

No.

Part

No.

Description

40946-0-1019 Page 15

MODEL DV-210 SHOWN

PARTS VIEW

MODEL DV-210 SHOWN

40946-0-1019Page 16

DVB-1 For Direct Vent Wall Furnaces DV210 and DV215

INSTALLING OPTIONAL BLOWER DVB-1. The blower must be

positioned as shown in Figure 1. Relocate gas line, if necessary,

using elbow tting at the gas valve, and move Piezo Spark Genera-

tor to the next screw. A slot on the bottom of the blower package

engages a tab on the bottom of the inner casing and is secured by

one screw in front.

BLOWER

MOUNTING

TAB

Figure 1

Attaching Switch Box

1. Facing combustion chamber, remove (2) top, left screws on the

combustion chamber door.

2. Align (2) clearance holes on the switch box (with fan control)

over (2) clearance holes on the combustion chamber door.

3. Insert and attach (2) screws removed in Step 1 into switch box

and combustion chamber door.

4. Attach switch box cover to switch box with (1) No. 8 x 1/4" screw.

OPTIONAL BLOWER INSTALLATION INSTRUCTIONS

Wiring

The appliance, when installed, must be electrically grounded in

accordance with local codes or, in the absence of local codes, with

the National Electrical Code, ANSI/NFPA 70 or Canadian Electrical

Code, CSA C22.1, if an external electrical source is utilized. This

appliance is equipped with a three-prong [grounding] plug for your

protection against shock hazard and should be plugged directly into

a properly grounded three-prong receptacle. Do not cut or remove

the grounding prong from this plug. For an ungrounded receptacle,

an adapter, which has two prongs and a wire for grounding, can

be purchased, plugged into the ungrounded receptacle and its

wire connected to the receptacle mounting screw. With this wire

completing the ground, the appliance cord plug can be plugged

into the adapter and be electrically grounded. A 7/8" (22mm) hole

is provided in the junction box for use with a conduit connector if

local codes require this type of protection.

CAUTION

Label all wires prior to disconnection when servicing controls.

Wiring errors can cause improper and dangerous operation.

Verify proper operation after servicing.

NOTICE: Unplugging of blower accessory will not stop the heater

from cycling. To shut heater off, turn knob on gas control to off,

depressing slightly. Do not force.

40946-0-1019 Page 17

Index No. Part No. Description

1 R-1268 Wire Assembly

2 R-896 Bushing (Three Required)

3 R-1156 Fan Control

4 DV-806 Switch Box

5 DV-807 Switch Box Cover

6 TH-111 Junction Box

7 R-1410 Bushing (Strain Relief)

8 R-285 Motor

9 R-587 Motor Cushion

10 TH-341 Blower Cushion

11 TH-356 Motor Support Assembly

12 R-319 Blower Wheel

13 TH-135 Blower Housing Assembly

14 R-315 Cord Set

DVB-1 For Direct Vent Wall Furnaces DV210 and DV215

OPTIONAL BLOWER INSTALLATION INSTRUCTIONS

Oiling the Motor

Oiling holes are provided on each end of the motor for oiling. The

blower should have ve drops of #20 motor oil every 6 months.

Do not use machine oil.

Cleaning the Blower Wheel

In some areas, such as near bedrooms and on oors with a hard

surface, the blower wheel will be lled with lint very quickly. A visual

check of the blower wheel should be made after 30 days use. The

blower will run faster with a dirty wheel, but move less air. Remove

the entire blower and clean each blade of the wheel with a tooth

brush as often as necessary.

40946-0-1019Page 18

To Order Parts Under Warranty, please contact your local Empire dealer. See the dealer locator at www.empirecomfort.

com. To provide warranty service, your dealer will need your name and address, purchase date and serial number, and the

nature of the problem with the unit.

To Order Parts After the Warranty Period, please contact your dealer or one of the Master Parts Distributors listed below.

This list changes from time to time. For the current list, please click on the Master Parts button at www.empirecomfort.com.

Please note: Master Parts Distributors are independent businesses that stock the most commonly ordered Original Equip-

ment repair parts for Heaters, Grills, and Fireplaces manufactured by Empire Comfort Systems Inc.

MASTER PARTS DISTRIBUTOR LIST

Parts Not Under Warranty

Parts can be ordered through your Service Person, Dealer, or a Master Parts Distributor. See this page for the Master Parts Distribu-

tors list. For best results, the service person or dealer should order parts through the distributor. Parts can be shipped directly to the

service person/dealer.

Warranty Parts

Warranty parts will need a proof of purchase and can be ordered by your Service Person or Dealer. Proof of purchase is required for

warranty parts.

All parts listed in the Parts List have a Part Number. When ordering parts, rst obtain the Model Number and Serial Number from the

name plate on your equipment. Then determine the Part Number (not the Index Number) and the Description of each part from the fol-

lowing illustration and part list. Be sure to give all this information . . .

Appliance Model Number Part Description

Appliance Serial Number Part Number

Type of Gas (Propane or Natural)

Do not order bolts, screws, washers or nuts. They are standard hardware items and can be purchased at any local hardware store.

Shipments contingent upon strikes, res and all causes beyond our control.

HOW TO ORDER REPAIR PARTS

Dey Distributing

1401 Willow Lake Boulevard

Vadnais Heights, MN 55101

Phone: 651-490-9191

Toll Free: 800-397-1339

Website: www.deydistributing.com

Parts: Heater, Hearth and Grills

F. W. Webb Company

200 Locust Street

Hartford, CT 06114

Phone: 860-722-2433

Toll Free: 800-243-9360

Fax: 860-293-0479

Toll Free Fax: 800-274-2004

Websites: www.fwwebb.com & www.victormfg.com

Parts: Heater, Hearth and Grills

East Coast Energy Products

10 East Route 36

West Long Branch, NJ 07764

Phone: 732-870-8809

Toll Free: 800-755-8809

Fax: 732-870-8811

Website: www.eastcoastenergy.com

Parts: Heater, Hearth and Grills

40946-0-1019 Page 19

WARRANTY

Empire Comfort Systems Inc. warranties this space heating product to be free from defects at the time of purchase and for the periods

specied below. Space heating products must be installed by a qualied technician and must be maintained and operated safely, in

accordance with the instructions in the owner’s manual. This warranty applies to the original purchaser only and is not transferable. All

warranty repairs must be accomplished by a qualied gas appliance technician.

Limited Ten-Year Parts Warranty – Combustion Chamber

Empire promises to the owner that if the combustion chamber (see parts list) fails because of defective workmanship or

material with ten years from the date of purchase, Empire will repair or replace at Empire’s option.

Limited One-Year Parts Warranty – Remote Controls, Accessories, and Parts

Should any remote control, accessory, or other part fail because of defective workmanship within one year from the date of

purchase, Empire will repair or replace at Empire’s option.

Duties Of The Owner

The appliance must be installed by a qualied installer and operated in accordance with the instructions furnished with the

appliance. A bill of sale, cancelled check, or payment record should be kept to verify purchase date and establish warranty

period. Ready access to the appliance for service.

What Is Not Covered

Damages that might result from the use, misuse, or improper installation of this appliance.

Travel, diagnostic costs and freight charges on warranted parts to and from the factory.

Claims that do not involve defective workmanship or materials.

Unauthorized service or parts replacements.

Removal and reinstallation cost.

Inoperable due to improper or lack of maintenance.

How To Get Service

To make a claim under this warranty, please have your receipt available and contact your installing dealer. Provide the dealer

with the model number, serial number, type of gas, and purchase verication. The installing dealer is responsible for providing

service and will contact the factory to initiate any warranted parts replacements. Empire will make replacement parts available

at the factory. Shipping expenses are not covered.

If, after contacting your Empire dealer, service received has not been satisfactory, contact: Consumer Relations Department,

Empire Comfort Systems Inc., PO Box 529, Belleville, Illinois 62222, or send an e-mail to [email protected] with

“Consumer Relations” in the subject line.

Your Rights Under State Law

This warranty gives your specic legal rights, and you may also have other rights, which vary from state to state.

40946-0-1019Page 20

www.empirecomfort.com

Empire Comfort Systems Inc.

Belleville, IL

If you have a general question

about our products, please e-mail

us at [email protected].

If you have a service or repair

question, please contact your dealer.

La page est en cours de chargement...

Empire Heating Systems Direct Vent Wall Furnace Heating System Le manuel du propriétaire

Marque: Empire Heating Systems

Modèle: Direct Vent Wall Furnace Heating System

Taper: Le manuel du propriétaire

Ce manuel convient également à

Télécharger le PDF

rapport

Empire Heating Systems Direct Vent Wall Furnace Heating System Le manuel du propriétaire

Ce manuel convient également à

Empire Heating Systems Direct Vent Wall Furnace Heating System Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents