1
PS-3515
PS-3516
PS-3615
PS-3616
Package Contents
Fanless LCD touch terminal……………………………..(x1)
Power adaptor…………………………………………..(x1)
Power cord……………………………………………...(x1)
User Manual…………………………………………….(x1)
Recovery DVD…………………………………………(x1)
(for pre-loaded OS model only)
※ The appearance of the product may be somewhat different from that of
the actual product, so the appearance of this product should be based
on that of physical products. The contents in this manual may be
updated at any time without prior notice.
PS-3515/3516/3615/3616
Fanless Touch Terminal
User Manual
13110904010 Ver. A0
http://www.posiflex.com
2
SOME IMPORTANT NOTES
FCC NOTES
This system meets industry & government requirements and applicable standards.
This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions manual, may cause
interference to radio communications. It has been tested and found to comply with
limits for a Class A digital device pursuant to subpart B of Part 15 of FCC Rules,
which are designed to provide reasonable protection against interference when
operated in a commercial environment. Operation of this equipment in a residential
area is likely to cause interference in which case the user at his own expense will
be required to take whatever measures to correct the interference.
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
CE CLASS A WARNING
This equipment is compliant with Class A of CISPR 32. In a residential
environment this equipment may cause radio interference.
AVERTISSEMENT CE CLASSE A
Cet équipement est conforme à la classe A de CISPR 32. Dans un environnement
résidentiel, cet équipement peut provoquer des interférences radio.
WARRANTY LIMITS
Warranty will terminate automatically when the machine is opened by any person
other than the authorized technicians. The user should consult his/her dealer for the
problem happening. Warranty voids if the user does not follow the instructions in
application of this merchandise. The manufacturer is by no means responsible for
any damage or hazard caused by improper application.
LIMITES DE GARANTIE
La garantie prend fin automatiquement lorsque la machine est ouverte par une
personne autre que les techniciens autorisés. L'utilisateur doit consulter son
revendeur pour le problème qui se produit. La garantie s'annule si l'utilisateur ne
suit pas les instructions d'application de cette marchandise. Le fabricant n'est en
aucun cas responsable de tout dommage ou danger causé par une mauvaise
application.
警告使用者
此為甲類資訊技術設備，於居住環境中使用時，可能會造成射頻擾動，在此
3
種情況下，使用者會被要求採取某些適當的對策。
SAFETY INSTRUCTIONS
This equipment is not suitable for use in locations where children are likely to be
present.
CONSIGNES DE SÉCURITÉ
Cet équipement ne convient pas à une utilisation dans des lieux pouvant accueillir
des enfants.
BATTERY CAUTION NOTES
Dispose of used batteries according to the instructions.
Replacement of a battery with an incorrect type that can defeat a safeguard
(for example, in the case of some lithium battery types)
Disposal of a battery into fire or a hot oven, or mechanically crushing or
cutting of a battery that can result in an explosion.
Leaving a battery in an extremely high temperature surrounding
environment that can result in an explosion or the leakage of flammable
liquid or gas.
A battery subjected to extremely low air pressure that may result in an
explosion or the leakage of flammable liquid or gas.
BATTERIE ATTENTION NOTES
Jetez les piles usagées conformément aux instructions.
Remplacement d'une batterie avec un type incorrect qui peut annuler une
sauvegarde (par exemple, dans le cas de certains types de batterie au
lithium)
Mise au rebut d'une batterie dans le feu ou dans un four chaud, ou
écrasement ou coupure mécanique d'une batterie pouvant entraîner une
explosion.
Laisser une batterie dans un environnement environnant à des températures
extrêmement élevées pouvant entraîner une explosion ou la fuite de liquide
ou de gaz inflammable.
Une batterie soumise à une pression atmosphérique extrêmement basse
pouvant provoquer une explosion ou une fuite de liquide ou de gaz
inflammable.
警告
本電池如果更換不正確會有爆炸的危險，請依製造商說明書處理用過之電
池。
4
Terminal from shipping mode to operation mode
In consideration of proper packaging, before shipping, the terminal is folded,
staying in shipping mode. Thus, when receiving the product, you will find that
the terminal is well folded, as shown below.
Before operating this terminal, unfold it and make this terminal rise in
operation mode by referring to the following steps. Here, an equivalent model
with GEN 7 base is taken below for example.
1. Firstly, lift this terminal gently to make
it to be unfolded.
2. Overturn this terminal in the direction
as indicated by the arrow in the right
figure.
3. Place this terminal on a flat table.
5
4. Tilt this terminal to a degree in the direction as indicated by the arrow
below.
Terminal from operation mode to shipping mode
To fold this terminal, refer to the following steps. Here, an equivalent model
with GEN 7 base is taken below for example.
1. Remove the cable cover.
2. Carefully hold the lower rim of the display.
6
3. Push the base-folding lever in the direction as indicated by the arrow
below (1). Then, the display will be loosen and go down (2).
4. When the display goes down to a degree, loose the base-folding lever, as
shown in the direction as indicated by the arrow below.
5. Then, gently tilt the display in the direction as indicated by the arrow
below until the display is well folded.
1
2
7
6. Put back the cable cover.
Overviews of the PS-3515/3516/3615/3616
Front View
PS-3515 PS-3516
PS-3615 PS-3616
Resistive Touch Panel
Gen 7E Base
LED Indicator
LED Indicator
Gen 7E Base
P-CAP Touch Panel
8
Rear View
Left Side View Right Side View
Bottom View
Bottom I/O Cover
Power Button
Brightness
Adjustment Button “+”
Brightness
Adjustment Button “-”
Rear I/O Cover
Hinge for LCD
Neck Cover
Cable Cover
Cable Exit
2
nd
Display
Screw Hole
Side Attachment
Cover
9
View of I/O Interface
Top I/O Ports
1
COM4 Port
2
USB 2.0 Port
※
The top I/O ports are provided for COM-based and USB-based peripheral
devices, for example, customer display.
Bottom I/O Ports
1
RJ45 LAN Port
2
USB 2.0 Ports
3
USB 3.0 Ports
4
VGA Port
5
COM Port (COM1/COM2/COM3)
6
RJ11 Cash Drawer Port
7
12VDC-IN Power Jack
-
-
Installing Optional Upgrade Kits and Peripherals
PS-3515/3516/3615/3616 can work with multiple optional upgrade kits and
peripheral devices, such as magnetic stripe reader (MSR), LCD monitor, cash
drawer and the like.
Before installing an optional upgrade kit and/or peripheral device, make sure
that the system is powered off and the external power source is removed from
the POS box to prevent electric hazard! Failure to follow the warning
description will void the product warranty!
For the detailed instruction, refer to each of the user manuals of the optional
upgrade kits and peripheral devices.
1
2
1
2
3
5
6
7
4
10
Connecting Power Adapter and I/O Cables
Before connecting power adapter and I/O cables to the I/O ports of PS series
terminal, please route and arranging the cables. Refer to the following step-by-
step instruction of cable routing and arrangement for the details. Here, an
equivalent model with GEN 7 base is taken below for example.
1. Press the circled section of the cable
cover with your thumb.
2. Pull out the cable cover.
3. Push and tilt the terminal to the end in
the direction as shown by the arrow.
Then determine that the terminal is tilted
to the end, as shown in the right figure.
Pull out
11
4. Press the circled section with two
thumbs and pull by force the two sides
of the locking hook with two forefingers
as indicated by the arrow.
5. Remove the neck cover from the base
stand.
6. Tilt the terminal slightly at a little angle in the direction as shown by the
arrow, making cables easily pass through the cable passage.
7. Make the connector, which will be connected to the I/O port of the
terminal, pass through the cable passage of base stand.
Cable Passage
12
8. Push and tilt the terminal to the
end in the direction as shown by
the arrow.
9. Remove the bottom I/O cover
with your forefinger inserting
the middle hole of the cover.
10. Connect the connector of the
power adapter to the 12VDC-IN
power jack.
11. Cover the bottom I/O interface and gather the I/O cables to the circled
cable arrangement area, as shown below.
13
12. Push and tilt the terminal to the end in the
direction as shown by the arrow.
13. Arrange well the I/O cable located at the
area of neck cover.
14. Shield the I/O cable arrangement area on the neck of the base stand with
the neck cover.
15. Shield the I/O cable exposure area with the cable cover.
14
CAUTION: On doing insertion or extraction of a cable connector, please
always hold the connector head itself instead of pulling the cable wire.
Doing this could damage the cables and ports, which is considered as an
artificial damage and is not covered by the warranty. The means of power
cord should be connected to a socket-outlet with earthing connection.
ATTENTION: Lors de l'insertion ou de l'extraction d'un connecteur de
câble, veuillez toujours tenir la tête du connecteur elle-même au lieu de
tirer le fil du câble. Cela pourrait endommager les câbles, ce qui est
considéré comme un dommage artificiel et n'est pas couvert par la
garantie. Le cordon d'alimentation doit être connecté à une prise de
courant avec mise à la terre.
Powering ON the PS-3515/3516/3615/3616
After connecting the power cable to the power jack of the
terminal, press the power button to power on the terminal. To
power it off, press the power button again.
Once powering off the system, if you want to power it on
again, please wait at least 3 seconds.
If the system hangs due to a reason, such as software resource conflict, please
press and hold the power button for over 10 seconds to forcedly shut down the
system.
Power LED Indicator
LED status indicator, which is located at the lower right side of the LCD panel,
is mainly responsible for notifying users of the current system status by
emitting various LED signals. The table provided below shows all the possible
LED status as a quick reference.
LED
Status
Description
POWER
Solid blue
System power ON
Solid orange
System standby
Installing an Operating System
This product is highly professional equipment. Therefore, we do NOT
encourage you to install any operating system into this machine without
professional assistance. We shall not be responsible for any technical support
to questions on this aspect. We suggest that you contact your dealer for OS
installation.
15
Operating System Recovery
For the PS-3515/3516/3615/3616 main system preloaded with an operating
system on HDD or SSD, We provide a recovery DVD shipped with the main
system for the preloaded operating system. The system integrator shall take
care of software restoration after the OS is recovered.
If you plan to recover your operating system, we do NOT encourage you to
recover any operating system. Please contact your service center for operating
system recovery.
Operation Environment
This terminal must NOT be operated in an environment with restricted
ventilation. There must be at least 25 mm air clearance around any top or side
ventilation holes with free flow of air around the unit at all times for system
operation.
16
Specifications
Model
PS-3515/3516/3615/3616
System
Configuration
Processor
Intel Apollo Lake N3350/J3455
System
Memory
SO-DIMM x 1, DDR3L
Storage Device
1 x M.2 port (M.2 2280 / B+M key)
(M.2 support s SATA interface signal only)
Power Supply
12V/40W
OS support
Windows 10 IoT
Display & Touch
LCD
PS-3515/3615: 15” (1024x768) with LED backlight
PS-3516/3616: 15.6” (1366x768) with LED backlight
Touch
PS-3515/3516: Resistive Touch
PS-3615/3616: P-CAP Touch
I/O & Expansion
Serial Port
4, 3 x DB9 on bottom I/O plate + 1 x RJ50 on top I/O
plate, 5V/12V support on all COM ports
Standard USB
Port
5, 2 x USB3.0 + 2 x USB2.0 on bottom I/O plate +
1 x USB2.0 on top I/O plate
Internal USB
Port
2 x USB 2.0
Powered USB
Port
Via PU490 in GEN8 base
LAN Port
10 / 100 / 1000 Mb x 1
Display Port
VGA x 1, 12V support for Posiflex monitors
CR Port
1, control 2 CR
Audio
Buzzer + 1 x internal 2W speaker (optional)
Base Stand
7th generation foldable base stand
Expansion Slot
1 x M.2 (M.2 2230 / E Key)
Environmental
Operating
Condition
0°C - 40°C, 20%RH - 90%RH
Storage
Condition
-20°C - 70°C, 10%RH - 90%RH
※
The product information and specifications are subject to change without
prior notice. To get the detailed information on the PS-
3515/3516/3615/3616, please check this model from Posiflex Global
Website.
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
Posiflex PS-3515 Manuel utilisateur
- Catégorie
- Terminaux de point de vente
- Taper
- Manuel utilisateur
dans d''autres langues
- English: Posiflex PS-3515 User manual
Documents connexes
-
Posiflex PS-3216A Manuel utilisateur
-
-
-
-
-
-
-
-
Posiflex XT-6317/6517 Manuel utilisateur
-
Posiflex XT-6515E Manuel utilisateur