Maytag Bottom freezer refrigerator Manuel utilisateur

Marque: Maytag

Modèle: Bottom freezer refrigerator

Catégorie: Congélateurs

Taper: Manuel utilisateur

Form No. A/02/03 Part No. 12642726 h t t p : / / w w w . m a y t a g . c o m 16022155 Litho U.S.A.

BOTTOM FREEZER REFRIGERATOR

care & cleaning

safety

Installer: Please leave this manual with

this appliance.

Consumer: Please read and keep this

manual for future reference. Keep sales

receipt and/or cancelled check as proof of

purchase.

If you have questions, write us (include

your model number and phone number)

or call:

Maytag Services

Attn: CAIR

Center

P.O. Box 2370

Cleveland, TN 37320-2370

1-800-688-9900 U.S.A.

1-800-688-2002 Canada

1-800-688-2080 (U.S.A. TTY for

hearing or speech impaired)

(Mon.-Fri., 8 a.m.-8 p.m. Eastern Time)

Internet: http://www.maytag.com

For service information, see page 21.

In our continuing effort to improve

the quality and performance of our

appliances, it may be necessary to

make changes to the appliance

without revising this guide.

before you call

Page 1

Pages 2-7

Page 8

Page 11

Pages 9-10

Pages 12-13

Page 14

Pages 14-16

Page 17

Pages 18-19

Page 21

Page 22

Page 44

Model Number

Serial Number

Date of Purchase

operating sounds

food storage tips

looking inside

ice service

proper temperatures

installation

storing the refrigerator

Safety

What you need to know

about safety

instructions

Warning and Important Safety

Instructions appearing in this manual are

not meant to cover all possible conditions

and situations that may occur. Common

sense, caution, and care must be

exercised when installing, maintaining, or

operating refrigerator.

Always contact your dealer, distributor,

service agent, or manufacturer about

problems or conditions you do not under-

stand.

Save these instructions

DANGER – Immediate hazards which

WILL result in severe personal injury

or death.

DANGER

WARNING – Hazards or unsafe prac-

tices which COULD result in severe

personal injury or death.

WARNING

CAUTION – Hazards or unsafe prac-

tices which COULD result in minor

personal injury.

CAUTION

To reduce risk of fire, electric shock, serious injury or death when using your refrigerator, follow these basic precautions,

including the following:

WARNING

To reduce risk of injury or death,

follow basic precautions, including

the following:

IMPORTANT: Child entrapment and

suffocation are not problems of the

past. Junked or abandoned refrigera-

tors are still dangerous – even if they

sit out for “just a few days.” If you are

getting rid of your old refrigerator,

please follow the instructions below to

help prevent accidents.

Before you throw away your old refrig-

erator or freezer:

➢ Take off the doors.

➢ Leave the shelves in

place so children

may not easily climb

inside.

DANGER

RECOGNIZE SAFETY

SYMBOLS, WORDS,

LABELS

1. Read all instructions before using the refrigerator.

2. Observe all local codes and ordinances.

3. Be sure to follow grounding instructions.

4. Check with a qualified electrician if you are not sure this

appliance is properly grounded.

5. DO NOT ground to a gas line.

6. DO NOT ground to a cold-water pipe.

7. Refrigerator is designed to operate on a separate 103 to

126 volt, 15 amp., 60 cycle line. DO NOT modify plug on

power cord. If plug does not fit electrical outlet, have proper

outlet installed by a qualified electrician.

8. DO NOT use a two-prong adapter, extension cord or power

strip.

9. DO NOT remove warning tag from power cord.

10. DO NOT tamper with refrigerator controls.

11. DO NOT service or replace any part of refrigerator unless

specifically recommended in User Guide or published user-

repair instructions. DO NOT attempt service if instructions are

not understood or if they are beyond personal skill level.

12. Always disconnect refrigerator from electrical supply before

attempting any service. Disconnect power cord by grasping

the plug, not the cord.

13. Install refrigerator according to Installation Instructions. All

connections for water, electrical power and grounding must

comply with local codes and be made by licensed person-

nel when required.

14. Keep your refrigerator in good condition. Bumping or drop-

ping refrigerator can damage refrigerator or cause refriger-

ator to malfunction or leak. If damage occurs, have refrig-

erator checked by qualified service technician.

15. Replace worn power cords and/or loose plugs.

16. Always read and follow manufacturer’s storage and ideal

environment instructions for items being stored in refrigerator.

For further assistance, call 1-800-688-9900 U.S.A., 1-800-688-2002 Canada or www.maytag.com

2. Remove toe grille and bottom bracket

cover(s).

• Open freezer door as wide as

possible.

• Depending on the model of your

refrigerator, you may have one or

two bracket covers.

3. Remove top hinge

cover from refrigerator

door by removing

Phillips screw.

• Retain screw and

cover for replace-

ment.

4. Unscrew

⁄16" hex head

screws from top hinge

to remove hinge.

• Retain all screws for

later use.

5. Lift refrigerator door from center hinge

pin.

6. For freezer door models

only: Hold freezer door

while removing hinge pin

with a

⁄16

"hex head driver.

Remove door from bottom hinge.

• Retain hinge pin for later use.

For freezer drawer models only:

Remove center hinge pin with a

⁄16" hex

head driver.

• Retain hinge pin for later use.

7. Remove Phillips

screws to remove

center hinge.

• Retain all screws

for later use.

8. Remove bottom hinge or stabilizing

bracket with

⁄8" hex head driver.

• Retain screws for

later use.

• Lift out bottom hinge

pin (select models).

Installation

Your new refrigerator was packed care-

fully for shipment. Remove and discard

shelf packing clips (if used) located just

above each shelf where they hook onto

the frame. To remove plastic clips wiggle

the clips sideways and pull straight out.

Measuring the opening

⁄2" of air space should be provided for the

top and back of the refrigerator. When

installing your refrigerator, measure carefully.

Subflooring or floor coverings (i.e. carpet,

tile, wood floors, rugs) may make your

opening smaller than anticipated.

Some clearance may be gained by using

the leveling procedure under How to

Level Your Refrigerator (page 7).

IMPORTANT: If refrigerator is to be

installed into a recess where top of refrig-

erator is completely covered, use dimen-

sions from floor to top of hinge cap to ver-

ify proper clearance.

Transporting your

refrigerator

Follow these tips when moving the refrig-

erator to final location:

➢ NEVER transport refrigerator on its

side. If an upright position is not possi-

ble, lay refrigerator on its back. Allow

refrigerator to sit upright for approxi-

mately 30 minutes prior to plugging

refrigerator in to assure oil return to

the compressor. Plugging refrigerator

in immediately may cause damage to

internal parts.

➢ Use an appliance dolly when moving

refrigerator. ALWAYS truck refrigera-

tor from its side or back–NEVER from

its front.

➢ Protect outside finish of refrigerator

during transport by wrapping cabinet

in blankets or inserting padding

between the refrigerator and dolly.

➢ Secure refrigerator to dolly firmly with

straps or bungee cords. Thread straps

through handles when possible. DO NOT

overtighten. Overtightening restraints

may dent or damage outside finish.

Selecting the best

location

Observe these points when choosing the

final location for your refrigerator:

➢ DO NOT install refrigerator near oven,

radiator or other heat source. If not

possible, shield refrigerator with

cabinet material.

➢ DO NOT install where temperature

falls below 55° F (13° C). Malfunction

may occur at this temperature.

➢ Make sure floor is level. If floor is not

level, shim rear wheels of refrigerator

with a piece of plywood or other shim

material.

➢ To assure proper door closure, verify

that the refrigerator is leveled with a

⁄4"

tilt to the back.

How to remove the

doors and hinges

Some installations require door removal

to get refrigerator to final location. If

removal of the pullout drawer is required,

see later section entitled How to

Remove and Install the Pullout Drawer

(page 5).

To avoid electrical shock which can

cause severe personal injury or death,

observe the following:

➢ Disconnect power to refrigerator

before removing doors. Connect

power only after replacing doors.

WARNING

To avoid damage to walls and flooring,

protect soft vinyl or other flooring with

cardboard, rugs or other protective

material.

CAUTION

1. Unplug power cord from power

source.

safety

How to reverse the

doors

1. Perform all steps listed in How to

Remove the Doors and Hinges

(page 2).

2. Transfer cabinet

plugs and cabinet

screws to opposite

side of cabinet.

• Remove cabinet

plugs with flat

blade of screw-

driver tip wrapped

in masking tape.

• Remove center mullion screws with

⁄16" hex head screwdriver.

• For swing doors only: Remove

bottom mullion screws with

⁄8" hex

head driver.

3. Transfer door stops from bottom edge

of fresh food door and freezer door

(select models) to opposite side of

door edge.

• Use a Phillips

screwdriver for

removal and

installation.

4. See How to Install and Remove

Handles (page 3) to remove and

reinstall handles.

5. Proceed to How to Replace the

Doors and Hinges to mount doors

(page 4).

To avoid possible injury and damage

to property, place doors on a nonabra-

sive surface protected by towels or

rugs while working directly on doors.

CAUTION

* Fasteners may require either a T-15 Torx

driver or a Phillips screwdriver.

Torx

is a registered trademark of Textron Inc.

Installation,

cont.

How to install and

remove handles

For easier installation, some refrigerators

may have been delivered with the han-

dles off. Please see the interior of the

fresh food section, or the back of your

refrigerator, to locate the handle assem-

bly. In case future transport of the refrig-

erator is necessary, or panels need to be

removed and replaced, the removal

instructions have been included here for

your convenience.

Handle design may vary from refrigerator

to refrigerator. Please reference the

instructions for the appropriate handle

design below.

FRESH FOOD HANDLES

Installing Front-Mounted Handles

1. Remove

⁄4" hex head

screws from door face

with hex head driver,

and Phillips screw from

top of door.

• If reversing door, remove door plugs

from opposite side of door and insert

in screw holes.

2. Align handle holes with screw

holes on door face and secure

with 2 door face

screws from step 1.

3. Locate handle trim in

literature pack and install

over top and bottom of

handle, as illustrated.

• Secure top handle trim

with remaining screw

removed in step 1.

• Snap bottom trim over

bottom portion of handle.

Removing Front-Mounted Handles

1. Remove top handle trim by

removing top handle

screw.

• Retain trim and screw for

later replacement.

2. Pry bottom handle trim

from handle with screw-

driver flat blade wrapped

in masking tape.

• Retain trim for later

replacement.

3. Remove two

⁄4" hex head screws.

• Retain screws for later replacement.

Installing Side-Mounted Handles

➢ Install handle by

fastening with

screws* removed

from edge of door.

NOTE: If reversing

door, remove door plugs from opposite

side of door and insert in screw holes.

Removing Side-Mounted Handles

➢ Remove handle by

removing three

screws* from side of

door.

• Retain screws for

later replacement.

Installing Stainless Steel

Front-Mounted Handles

1. Loosen one door clip on

door with

⁄4" hex head driver.

2. Locate predrilled hole

at base of handle, and

fit hollow end of handle

over door clip.

3. Fit other end of handle over other door

clip and slide up as far as possible.

NOTE: If top of handle does not fit

over top clip, loosen lower clip further

until fit can be accomplished.

4. Insert

⁄4" hex head driver into predrilled

hole at base of handle to tighten screw.

Insert screw plug(s) into hole(s).

Removing Stainless Steel

Front-Mounted Handles

1. Remove screw plug at

base of handle with a

very small flat-blade

screwdriver.

• Insert

⁄4" hex head driver

into predrilled hole to

remove screw.

2. Slide handle to remove from

door clip.

For further assistance, call 1-800-688-9900 U.S.A., 1-800-688-2002 Canada or www.maytag.com

* Fasteners may require either a T-15 Torx

driver or a Phillips screwdriver.

Torx

is a registered trademark of Textron Inc.

How to replace the

doors and hinges

1. Install hinge assemblies.

• Install top hinge loosely with

⁄16" hex

head screws.

• Install center hinge with Phillips

screws.

• Install bottom hinge with

⁄8" hex head

screws.

2. Insert bottom hinge pin

(select models).

• Locate bottom hinge

hole closest to out-

side edge of cabinet, and insert bot-

tom hinge pin. Replace any door

shims, if present.

3. For freezer door

models only: Place

hinge side of freezer

door on bottom hinge

pin and hold freezer door upright while

installing center hinge pin with

⁄16" hex

head driver.

• Replace any applicable door shims.

• Make sure the hinge pin is installed

tightly.

For freezer drawer models only:

Install center hinge pin with a

⁄16" hex

head driver.

• Replace any applicable door shims.

• Make sure the hinge pin is installed

tightly.

4. Place hinge side of refrigerator door

on center hinge pin.

5. While holding refrigerator

door upright, tighten

down top hinge with

⁄16"

hex head driver and

replace hinge cover.

installation

FREEZER HANDLES

Installing Partial-Width Handle

➢ Install handle by

fastening with screws

removed from edge

of door.

• If reversing freezer door, remove

door plugs from top edge of door and

insert into screw holes.

Removing Partial-Width Handle

➢ Remove handle by

removing screws

from top of handle.

• Retain screws for

later replacement.

Installing Full-Width Extruded Handle

➢ Install handle by fas-

tening with screws*

removed from edge of

door.

Removing Full-Width Extruded

Handle

➢ Remove handle by

removing three

screws* from handle.

• Retain screws for later replacement.

Installation,

cont.

3. Pull drawer open to full extension.

4. Remove Phillips screw from each side

of rail system. (Select models)

5. Lift top of door to unhook door sup-

ports from rail system. Lift door out to

remove.

To install:

1. Pull both rails out to full extension.

4. With drawer pulled out to full exten-

sion, insert lower basket by aligning

tabs on both sides of lower basket with

notches in rail assembly. Verify that

the basket sides are hooked securely

over the rails.

5. Slide upper basket into freezer. Make

sure that rear of basket hooks behind

rail catch.

3. Lower door into final position.

2. While supporting door, hook door sup-

ports into tabs located on inside of rail.

How to remove and

install the pullout

drawer

(SELECT MODELS)

To avoid electrical shock which can

cause severe personal injury or death,

disconnect power to refrigerator

before removing doors. After replacing

doors, connect power.

WARNING

To avoid possible injury, product, or

property damage, you will need two

people to perform the following

instructions.

CAUTION

To remove:

1. Pull upper basket out to full extension

and lift out to remove.

2. Remove lower basket by pressing

inward on basket sides, then lift

basket.

To prevent accidental child entrap-

ment or suffocation risk, DO NOT

remove the divider in the top freezer

basket.

DANGER

Press Tab Here

For further assistance, call 1-800-688-9900 U.S.A., 1-800-688-2002 Canada or www.maytag.com

How to connect the

water supply for

optional automatic

ice maker

MATERIALS NEEDED

➢

⁄4

" outer diameter flexible copper tub-

ing

➢ Shut-off valve (requires a

⁄

4" hole to be

drilled into water supply before valve

attachment)

➢ Needle-nose pliers

➢ Adjustable wrench

➢ Water bucket

➢ Flat-blade screwdriver

➢

⁄4" hex nut driver

➢ Phillips screwdriver

➢ Masking tape or small plastic bag

➢ Create service loop with tubing using

care to avoid kinks in tubing.

➢ Remove plastic cap from water valve

inlet port.

➢ Place brass nut and sleeve on copper

tube end as illustrated.

➢ Place end of copper tubing into water

valve inlet port. Shape tubing slightly –

DO NOT KINK – so that tubing feeds

straight into inlet port.

➢ Slide brass nut over

sleeve and screw

nut into inlet port.

Tighten nut with

wrench.

IMPORTANT: DO

NOT overtighten.

Cross threading may occur.

➢ Pull on tubing to

confirm connection

is secure. Connect

tubing to frame with

water tubing clamp

and turn on water

supply. Check for

leaks and correct, if

present.

➢ Monitor water connection for 24

hours. Correct leaks, if necessary.

NOTE

❚ Add 8' to tubing length needed to

reach water supply for creation of

service loop.

Brass

Nut Sleeve

To avoid property damage or possi-

ble injury, follow basic precautions,

including the following:

➢ Consult a plumber to connect

copper tubing to household plumb-

ing to assure compliance with local

codes and ordinances.

➢ Confirm water pressure to water

valve is between 20 and 100

pounds per square inch. If water

filter is installed, water pressure to

water valve must be a minimum of

35 pounds per square inch.

➢ DO NOT use a self-piercing, or

⁄16" saddle valve! Both reduce

water flow, become clogged over

time, and may cause leaks if repair

is attempted.

➢ Tighten nuts by hand to prevent

cross threading. Finish tightening

nuts with pliers and wrenches. Do

not overtighten.

➢ Wait 24 hours before placing refrig-

erator into final position to check

and correct any water leaks.

CAUTION

To reduce the risk of injury or

death, follow the basic precautions,

including the following:

➢ Read all instructions before

installing ice maker.

➢ DO NOT attempt installation if

instructions are not understood or if

they are beyond personal skill

level.

➢ Observe all local codes and ordi-

nances.

➢ DO NOT service ice maker unless

specifically recommended in

owner’s manual or published user-

repair instructions.

➢ Disconnect power to refrigerator

prior to installing ice maker.

WARNING

installation

How to level your

refrigerator

If your refrigerator requires an ice maker

water supply connection, proceed to How

to Connect the Water Supply for

Optional Automatic Ice Maker section

(page 6) before leveling your refrigerator.

To protect personal property or refrig-

erator from damage, observe the fol-

lowing:

➢ Protect soft vinyl or other flooring

with cardboard, rugs, or other

protective material.

➢ Do not use power tools when

performing leveling procedure.

CAUTION

MATERIALS NEEDED

➢

⁄8" hex head driver

➢ Level

1. Move refrigerator to final location and

plug in power cord.

2. Remove toe grille

and bottom

cover(s).

3. Turn left and right adjust-

ment screws (A) to

raise or lower front

of refrigerator.

• Make sure refriger-

ator cabinet is level

from side to side by

adjusting left and

right roller adjustment screws.

•Turn stabilizing leg clockwise until

firmly against floor.

• For Pullout Drawer Models: After

completing the above listed steps,

turn roller adjustment screws (A) 2 to

3 times counterclockwise, so that full

weight of refrigerator rests on stabi-

lizing legs.

4. Using a level, make sure front of

refrigerator is

⁄4" (6 mm) or

⁄2 bubble

higher than back of refrigerator.

• See leveling step 3 for assistance.

5. Replace toe grille and bracket

cover(s). See markings on inside of

toe grille to insure proper placement.

• Snap bottom portion into place

first. Press down on top part of grille

until top portion snaps into place.

Installation,

cont.

For further assistance, call 1-800-688-9900 U.S.A., 1-800-688-2002 Canada or www.maytag.com

SETTING AND MAINTAINING PROPER TEMPERATURES

The controls are located at the top front of the refrigerator and freezer compartments. NOTE: The freezer control turns the cooling

system on. Neither section will cool if freezer control is set to OFF.

Initial control settings

After plugging the refrigerator in, set the

controls.

➢ To adjust the controls, turn the control

knob to the left or right as desired.

➢ Initially set the refrigerator control on

➢ Initially set the freezer control on 4.

➢ Let the refrigerator run at least 8-12

hours before adding food.

Warm cabinet surfaces

At times, the front of the refrigerator cab-

inet may be warm to the touch. This is a

normal occurrence that helps prevent

moisture from condensing on the cabinet.

This condition will be more noticeable

when you first start the refrigerator, dur-

ing hot weather and after excessive or

lengthy door openings.

TEMPERATURE CONTROL GUIDE

Refrigerator too warm Turn the refrigerator control to next higher number.

Refrigerator too cold Turn the refrigerator control to next lower number.

Freezer too warm Turn the freezer control to next higher number.

Freezer too cold Turn the freezer control to next lower number.

Turn refrigerator OFF Turn the freezer control to OFF.

NOTE: Turning freezer control to OFF stops cooling in both compartments. It does not

shut off power to the refrigerator.

Adjusting the controls

➢ 24 hours after adding food, you may

decide that one or both compartments

should be colder or warmer. If so,

adjust the control(s) as indicated in the

table below.

➢ Except when starting the refrigerator,

do not change either control more

than one number at a time.

➢ Allow 5-8 hours for temperatures to

stabilize.

➢ Changing either control will have

some effect on the temperature of the

other compartment.

Refrigerator Control

Freezer Control

proper temperatures

Fresh food compartment

shelves

Your refrigera-

tor has either

Spill-

Catcher™ or Tempered Glass Shelves.

The Spill-Catcher™ shelves have a spill

retainer edge which allows for easier

clean up, and some are equipped with

the Easy Glide slide out feature.

To slide out (select models), grasp the

front of the shelf and pull forward. Push in

the shelf to return to the original position.

To remove and install 3-hook style shelf:

To remove a shelf, slightly lift up the rear

of the shelf and pull the shelf straight out.

To lock the shelf into another position, tilt

up the front edge of the shelf. Insert the

hooks into the desired frame openings and

let the shelf settle into place, being sure

the shelf is securely locked at the rear.

To remove and install single hook

style shelf:

To remove a shelf, slightly lift up the front

of the shelf and pull the shelf straight out.

To lock the shelf into another position, tilt

up the front edge of the shelf. Insert the

hooks into the desired frame openings and

let the shelf settle into place, being sure

the shelf is securely locked at the rear.

LOOKING INSIDE

DOOR STORAGE

The Pick-Off Door Bins are adjustable

and can be easily removed.

To remove, lift the bin front up until it

clears the retainers on the door liner then

pull the bin straight out.

To replace, reverse the above procedure.

DAIRY COMPARTMENT

(Select Models)

The dairy compartment provides conven-

ient storage for items such as butter and

margarine. This compartment is an

adjustable feature located in the door. It

can be moved to several different loca-

tions to accommodate storage needs.

To remove:

➢ Open dairy door, pull upward and tilt

out.

To reinstall:

➢ Reverse previous

procedure.

FULL WIDTH DOOR SHELF

The lower shelf on the door is full width

and not adjustable.

To remove for cleaning:

➢ Lift shelf up and out.

To reinstall:

➢ Reverse above pro-

cedure.

Special storage areas

Your refrigerator has a Snack Center

Drawer (select models).

To remove the Snack Center Drawer

for cleaning:

➢ Pull the drawer out until it stops.

➢ Lift the drawer up slightly and pull it out.

To reinstall the drawer:

➢ Reverse the above procedure.

This drawer can be positioned as desired

on either the left or right side of the refrig-

erator cabinet.

For best results, keep this drawer closed

tightly.

The Crispers provide storage for fruit

and vegetables. There is a humidity con-

trol (select models) located on the crisper

shelf above each of the crisper drawers.

➢ For fruit storage, slide the crisper control

toward the center to provide lower humidi-

ty conditions in the

drawer.

➢ For vegetable

storage, slide the

crisper control

away from the

center to provide

higher humidity conditions in the

drawer.

To remove a crisper drawer for clean-

ing:

➢ Pull out the crisper until it stops.

➢ Tilt the drawer front up and pull it out.

Never attempt to adjust a shelf that is

loaded with food (except in the case of

the Elevator™ Shelf).

WARNING

ELEVATOR™ SHELF

(Select Models)

The fresh food compartment is equipped

with an Elevator™ Shelf. This shelf has

a spill retainer edge for easy cleanup. It

also has the convenient slide out feature

that allows easy access to items stored at

the rear of the shelf.

This shelf can be adjusted up or down

without having to be unloaded of its con-

tents. To adjust an Elevator™ Shelf, pull

out the knob on the crank handle. Rotate

the crank clockwise to raise the height of

the shelf, and counterclockwise to lower

the height of the shelf.

To remove the Elevator™ shelf for occa-

sional cleaning, completely unload the

shelf and pull the shelf forward. When the

shelf stops, press up on the tabs located

underneath its outside edges, then con-

tinue pulling forward, clear of the frame.

To reinstall, align the shelf to the frame

and push it all the way back. (There is no

need to depress the tabs for reinstallation).

In ordinary use, the Elevator™ shelf with

the frame assembly does NOT require

removal. Though unlikely, and not recom-

mended, the correct removal procedure

is as follows:

Unload the shelf completely, raise the

shelf to its highest possible position. While

supporting the shelf and frame from the

front, press both locks inward. Lift slightly

and tilt the frame assembly to allow the

rear guides to clear the vertical rails.

To reinstall, tilt the frame assembly while

depressing both locks, reposition the rear

guide behind the vertical rails. When the

shelf is level, release the locks allowing

the shelf to latch in the correct position.

For further assistance, call 1-800-688-9900 U.S.A., 1-800-688-2002 Canada or www.maytag.com

To reinstall a crisper drawer:

➢ Align the drawer in the tracks.

➢ Lift the drawer front and slide in.

For best results, keep the crispers tightly

closed.

To remove the Crisper Top (select

models):

➢ Remove drawers as instructed above.

➢ Place hand beneath frame to push up

glass from underneath. Lift glass out.

➢ Lift frame from refrigerator liner rails.

To reinstall the Crisper Top (select

models):

➢ Repeat above instructions in reverse

order.

If door doesn’t open far enough to

remove drawers:

➢ Remove drawer furthest from hinge

side of cabinet.

➢ Remove glass as instructed previously.

➢ Lift center divider from frame. Slide

existing drawer away from hinge side

of cabinet and remove.

EGG CRADLE (Select Models)

Your refrigerator may come equipped

with an Egg Cradle (style may vary). It

can be removed to be washed or carried

to a work area.

MULTI-USE RACK

(Select Models)

The Multi-Use Rack

(select models) pro-

vides a place for stor-

ing wine horizontally.

The rack also holds canned beverages or

an egg carton. Position the rack on the

side of a refrigerator shelf. Note: The

Multi-Use Rack cannot be positioned on

an Elevator™ Shelf.

WIRE BASKET(Select Models)

To remove and install basket:

➢ To remove

basket, pull

basket out to

full exten-

sion. Tilt up

front of basket and pull straight out.

➢ To install, insert basket into refrigera-

tor liner rails and push back into place.

LOWER BASKET DIVIDER

(Select Models)

The Lower Basket Divider allows the

basket area to be organized into

sections.

To remove divider:

➢ Pull divider

straight up.

To reinstall divider:

➢ Hook top corners of divider over top

horizontal basket rungs.

Freezer door storage

FIXED DOOR SHELF

(Select Models)

The Fixed Door Shelf provides conven-

ient storage for frozen food items in freez-

er door.

To remove door shelf:

➢ Lift assembly from side liner tabs and

pull out.

To reinstall door shelf:

➢ Fit ends of shelf assembly on liner

tabs and slide down.

TILT-OUT BIN (Select Models)

The Tilt-Out Bin

in the freezer

door tilts for-

ward for easy

access to stored

items.

Freezer compartment

shelves and baskets

WIRE ICE SERVICE RACK

(Select Models)

To install:

➢ Position wire

rack against the

freezer wall,

above plastic

supports (A).

➢ Slide the rack down over the plastic

supports until the rear loops are firmly

seated.

To remove:

➢ Perform above steps in reverse order.

FIXED OR SLIDE-OUT

FREEZER SHELF

(Select Models)

To remove:

➢ Pull shelf out to full extension.

➢ Tilt up front of shelf and pull straight out.

To reinstall:

➢ Insert shelf onto freezer liner rails and

push to back of compartment.

PULLOUT DRAWER

BASKETS

(Select Models)

(Door assembly

of drawer

removed from

illustration for

visual clarity.)

To remove and replace baskets:

➢ See page 5 for basket removal and

replacement instructions.

To prevent accidental child entrap-

ment or suffocation risk, DO NOT

remove the divider in the top freezer

basket.

DANGER

looking inside

ICE SERVICE

Your refrigerator is automatic ice maker

ready. The number of the appropriate ice

maker kit is IC11. The kit contains instal-

lation instructions and water connection

instructions.

Other models have a factory installed ice

maker. Connect the ice maker to the

water supply as instructed in the separate

instructions furnished with the refrigera-

tor. Proper water flow and a level

refrigerator are essential for optimal

ice maker performance.

After your refrigerator has been connect-

ed to the water supply, move the sensor

arm into the down position. The ice

maker will fill with water when the freezer

reaches the proper temperature.

Using ice maker for the first time:

➢ Confirm ice bin is in place and ice

maker arm is down.

NOTE

❚ Energy rating guides that are post-

ed on the refrigerator at the time of

purchase do not include optional

ice maker energy usage.

➢ Allow approximately 24 hours after

installation to receive first harvest of ice.

➢ Discard ice created within first 12

hours of operation to verify system is

flushed of impurities.

Operating instructions:

➢ Confirm ice bin is in place and ice

maker arm is down.

➢ After freezer section reaches between

0° to 2° F (-18° to -17° C), ice maker

fills with water and begins operating.

You will have a complete harvest of

ice approximately every 3 hours.

➢ Stop ice production by raising ice

maker arm until click is heard.

➢ Ice maker will remain in the off posi-

tion until arm is pushed down.

➢ The first one or two batches will proba-

bly contain undersized and irregular

cubes because of air in the supply line.

➢ The initial batch may also contain

impurities from the new water supply

piping. Therefore, all cubes from the

first two or three batches should be

discarded.

➢ When the ice cubes are ejected it is

normal for several cubes to be joined

together at the ends. They can easily

be broken apart. The ice maker will

continue to make ice until the supply

of ice cubes raises the sensor arm,

shutting the ice maker off.

➢ Certain sounds may accompany the

various cycles of the ice maker. The

motor may have a slight hum, the

cubes will rattle as they fall into an

empty storage pan and the water

valve may click or “buzz” occasionally.

➢ If the ice is not used frequently, the ice

cubes will become cloudy, shrink, stick

together and taste stale. Empty the ice

storage bin periodically and wash it in

lukewarm water. Be sure to dry the bin

thoroughly before replacing it.

➢ Beverages and foods should not be

placed in the ice storage bin for quick

chilling. These items can block the

sensor arm, causing the ice maker to

malfunction.

➢ Turn off (arm up) the ice maker when

the water supply is to be shut off for

several hours.

To remove the ice bin:

➢ Pull it forward, away from the ice

maker. To avoid the ice maker dump-

ing ice while the bin is removed, turn

the ice maker off by raising the sensor

arm.

To reinstall the ice bin:

➢ Reverse the above procedure. Turn

the ice maker on by lowering the sen-

sor arm.

Ice cube trays

Some models are equipped with ice cube

trays and an ice storage bin. To release the

ice cubes from a tray, hold the tray upside

down over the bin and twist both ends.

Automatic ice maker

(optional)

➢ After freezer section reaches between

0° to 2° F (-18° to -17° C), ice maker

fills with water and begins operating.

FOR YOUR SAFETY

Do not place fingers or hands on

the automatic ice making mecha-

nism while the refrigerator is

plugged in. This will help protect

you from possible injury. It will also

prevent interference with moving

parts of the ejector mechanism and

the heating element that releases

the cubes.

Under certain rare circumstances,

ice cubes may be discolored,

usually appearing with a green-

bluish hue. The cause of this

unusual discoloration can be a

combination of factors such as cer-

tain characteristics of local waters,

household plumbing and the accu-

mulation of copper salts in an inac-

tive water supply line which feeds

the ice maker.

Continued consumption of such

discolored ice cubes may be injurious

to health. If such discoloration is

observed, discard the ice cubes

and contact your dealer to pur-

chase and install a water line filter.

WARNING

For further assistance, call 1-800-688-9900 U.S.A., 1-800-688-2002 Canada or www.maytag.com

ice service

FOOD STORAGE TIPS

Fresh food storage

➢ The fresh food compartment of a

refrigerator should be kept between

34° F and 40° F with an optimum tem-

perature of 37° F. To check the tem-

perature, place an appliance ther-

mometer in a glass of water and place

in the center of the refrigerator. Check

after 24 hours. If the temperature is

above 40° F adjust the controls as

explained on page 8.

➢ Avoid overcrowding the refrigerator

shelves. This reduces the circulation

of air around the food and results in

uneven cooling.

FRUITS AND

VEGETABLES

➢ Storage in the crisper drawers traps

moisture to help preserve the fruit and

vegetable quality for longer time peri-

ods. (Refer to page 9).

➢ Sort fruits and vegetables before stor-

age and use bruised or soft items first.

Discard those showing signs of decay.

➢ Always wrap odorous foods such as

onions and cabbage so the odor does

not transfer to other foods.

➢ While vegetables need a certain

amount of moisture to remain fresh,

too much moisture can shorten stor-

age times (especially leafy vegeta-

bles). Drain vegetables well before

storing.

MEAT AND CHEESE

➢ Raw meat and poultry should be

wrapped securely so leakage and

contamination of other foods or sur-

faces does not occur.

➢ Occasionally mold will develop on the

surface of hard cheeses (Swiss,

Cheddar, Parmesan). Cut off at least

an inch around and below the moldy

area. Keep your knife or instrument

out of the mold itself. The remaining

cheese will be safe and flavorful to

eat. Do NOT try to save individual

cheese slices, soft cheese, cottage

cheese, cream, sour cream or yogurt

when mold appears.

DAIRY FOOD

➢ Most dairy foods such as milk, yogurt,

sour cream and cottage cheese have

freshness dates on their cartons for

appropriate length of storage. Store

these foods in the original carton and

refrigerate immediately after purchas-

ing and after each use.

Frozen food storage

➢ The freezer compartment of a refriger-

ator should be kept at approximately

0° F. To check the temperature, place

an appliance thermometer between

the frozen packages and check after

24 hours. If the temperature is above

0˚ F, adjust the control as described on

page 8.

➢ A freezer operates more efficiently

when it is at least two-thirds full.

PACKAGING FOODS FOR

FREEZING

➢ To minimize dehydration and quality

deterioration use aluminum foil, freez-

er wrap, freezer bags or airtight con-

tainers. Force as much air out of the

packages as possible and be sure

they are tightly sealed. Trapped air

can cause the food to dry out, change

color and develop an off-flavor (freez-

er burn).

➢ Overwrap fresh meats and poultry

with suitable freezer wrap prior to

freezing.

➢ Do not refreeze meat that has com-

pletely thawed.

LOADING THE FREEZER

➢ Avoid adding too much warm food to

the freezer at one time. This overloads

the freezer, slows the rate of freezing

and can raise the temperature of

frozen foods.

➢ Leave space between the packages so

cold air can circulate freely, allowing

food to freeze as quickly as possible.

➢ Avoid storing hard-to-freeze foods

such as ice cream and orange juice on

the freezer door shelves. These foods

are best stored in the freezer interior

where the temperature varies less

with door openings.

Refer to the Food Storage Chart on

page 13 for approximate storage

times.

FOOD STORAGE CHART

(Storage times are approximate and may vary depending on type of packaging, storage temperature, and the quality of the food when

purchased.)

Foods

Butter

Milk & cream

Cream cheese, cheese

spread & cheese food

Cottage cheese

Sour cream

Hard cheese (Swiss,

Cheddar & Parmesan)

Eggs in the shell

Leftover yolks or whites

Apples

Bananas

Pears, plums, avocados

Berries, cherries, apricots

Grapes

Citrus fruits

Pineapples, cut

Asparagus

Brussels sprouts, broccoli, cau-

liflower, green peas, lima

beans, onions, peppers

Cabbage, celery

Carrots, parsnips, beets, &

turnips

Lettuce

Chicken and Turkey, whole

Chicken and Turkey, pieces

Fish

Bacon

Beef or lamb, ground

Beef or lamb, roast & steak

Ham, fully cooked, whole

half

slices

Luncheon meat

Pork, roast

Pork, chops

Sausage, ground

Sausage, smoked

Veal

Frankfurters

Refrigerator

1 month

1 week

1-2 weeks

3-5 days

10 days

1-2 months

3 weeks

2-4 days

1 month

2-4 days

3-4 days

2-3 days

3-5 days

1-2 weeks

2-3 days

1-2 days

3-5 days

1-2 weeks

7-10 days

1-2 days

7 days

1-2 days

3-5 days

7 days

5 days

3 days

3-5 days

1-2 days

7 days

3-5 days

7 days

Freezer

6-9 months

Not recommended

4-6 months

May become crumbly

Not recommended

9-12 months

8 months (cooked)

6 months (whole/peeled)

Not recommended

6 months

1 month (whole)

Not recommended

6-12 months

8-10 months

Not recommended

8-10 months

Not recommended

12 months

9 months

2-6 months

1 month

3-4 months

6-9 months

1-2 months

4-6 months

4 months

1-2 months

4-6 months

1 month

Storage Tips

Wrap tightly or cover.

Check carton date. Close tightly. Don’t return unused portions to

original container. Don’t freeze cream unless whipped.

Wrap tightly.

Store in original carton. Check carton date.

Wrap tightly. Cut off any mold.

Refrigerate small ends down.

For each cup of yolks to be frozen, add 1 tsp. sugar for use in

sweet, or 1 tsp. salt for non-sweet dishes.

May also store unripe or hard apples at 60-70° F.

Ripen at room temperature before refrigerating. Bananas and

avocados darken when refrigerated.

May also store at 60-70° F. If refrigerated, store uncovered.

Will not ripen after purchase. Use quickly.

Do not wash before refrigerating. Store in crisper.

Wrap odorous foods. Leave peas in pods.

Wrap odorous foods & refrigerate in crisper.

Remove tops. Wrap odorous foods and refrigerate in the crisper.

Keep in original packaging for refrigeration. Place in the Meat and

Cheese Drawer. When freezing longer than 2 weeks, overwrap

with freezer wrap.

Fresh meats can be kept in original packaging for refrigeration.

Place in the Meat and Cheese Drawer. When freezing longer than

2 weeks, overwrap with freezer wrap.

Unopened, vacuum-packed luncheon meat may be kept up to

2 weeks in the Meat and Cheese Drawer.

Processed meats should be tightly wrapped and stored in the Meat

and Cheese Drawer.

EGGS

FRUITS

DAIRY PRODUCTS

Sources: United States Department of Agriculture; Food Marketing Institute; Cooperative Extension Service, Iowa State University

VEGETABLES

MEATS

POULTRY & FISH

FOOD STORAGE TIPS

,CONT.

For further assistance, call 1-800-688-9900 U.S.A., 1-800-688-2002 Canada or www.maytag.com

storing the refrigerator

STORING THE REFRIGERATOR

Vacations

If you will be gone for a month or less,

leave the controls at the usual settings.

During longer absences:

1. Remove all food.

2. Shut off the ice maker (if installed) and

the valve where you tapped into the

water line to supply the refrigerator.

3. Disconnect the refrigerator from the

electrical outlet.

4. Clean and dry the refrigerator

thoroughly.

5. Leave the doors open to prevent

odors.

Moving

When moving, follow steps 1–4 under

Vacations. In addition, remove and care-

fully pack any items that are easily

removable. Ship the refrigerator in an

upright position with the doors taped

shut.

CARE AND CLEANING

Refer to the chart on the following page for

specific refrigerator cleaning guidelines.

REPLACING A LIGHT BULB

REFRIGERATOR

➢ Slide shield

toward back of

compartment to

release from light

assembly.

➢ Remove light bulbs.

➢ Replace with appliance bulbs no

greater than 40 watts.

➢ Replace light bulb cover by inserting

tabs on light shield into liner holes on

each side of light assembly. Slide

shield toward front of unit until it locks

into place. DO NOT force shield

beyond locking point. Doing so may

damage light shield.

FREEZER

➢ Pinch rear tabs on light cover and pull

straight down.

➢ Remove light bulb.

➢ Replace bulb with appliance bulb no

greater than 40 watts.

➢ Insert front tabs of light cover into

refrigerator liner and snap rear portion

over light assembly.

CONDENSER

Energy saving tips

➢ When placing refrigerator into final

position, allow for

⁄2

" clearance around

the top and sides of unit to supply

ample ventilation.

➢ Locate the refrigerator away from heat

producing appliances such as the

range or dishwasher, heat vents and

direct sunlight.

➢ Level the refrigerator and do not block

ventilation around the front grille.

➢ Keep the freezer full to near capacity

so less cold air will escape during door

openings. When the freezer is less

than two-thirds full, place milk cartons

half full of water in the freezer.

➢ Let hot dishes cool slightly before put-

ting into the refrigerator or freezer.

➢ Cover liquids.

➢ Wipe moisture from the outside of

containers before placing them into

the refrigerator.

➢ Avoid opening the doors too often.

➢ Clean condenser coils every 3 months.

➢ Do not use aluminum foil, wax paper

or paper toweling as shelf liners. This

decreases air flow and causes unit to

run less efficiently.

Cleaning of the condenser is recom-

mended every three months.

➢ Unplug the refrigerator.

➢ Remove the toe grille (see page 2) to

access the condenser coils.

➢ Using a vacuum cleaner hose, remove

the dust and soil.

➢ Use a vacuum cleaner hose with the

brush attachment to clean the con-

denser fan outlet grille at the back of

the refrigerator.

Disconnect the power cord or

disconnect the circuit breaker before

cleaning.

CAUTION

Disconnect the power cord or discon-

nect the circuit breaker before replac-

ing light bulb(s). Wear gloves as pro-

tection against broken glass.

CAUTION

Disconnect the power cord or discon-

nect the circuit breaker before clean-

ing the condenser.

CAUTION

PART DO

➢ Use 4 tablespoons (60 milliliters) of baking soda dissolved in

1 quart (1 liter) warm soapy water.

➢ Rinse surfaces with clean warm water and dry immediately to

avoid water spots.

➢ Use warm, soapy water and a soft, clean cloth or sponge.

➢ Rinse surfaces with clean warm water and dry immediately to

avoid water spots.

➢ After cleaning, rinse and dry. To restore luster and remove

streaks follow with Stainless Steel Magic Spray* (Part No.

20000008).

➢ Use a vacuum cleaner hose nozzle.

➢ Use a vacuum cleaner hose nozzle with brush attachment.

➢ Follow removal and installation instructions from appropriate

feature section.

➢ Allow items to adjust to room temperature.

➢ Dilute mild detergent and use a soft clean cloth or sponge for

cleaning.

➢ Use a plastic bristle brush to get into crevices.

➢ Rinse surfaces with clean warm water.

➢ Dry glass and clear items immediately to avoid spots.

DO NOT USE

➢ Abrasive or harsh cleaners

➢ Ammonia

➢ Chlorine bleach

➢ Concentrated detergents or

solvents

➢ Metal or plastic-textured

scouring pads

➢ Abrasive or harsh cleaners

➢ Ammonia

➢ Chlorine bleach

➢ Concentrated detergents or

solvents

➢ Metal or plastic-textured

scouring pads

➢ Vinegar-based products

➢ Citrus-based cleaners

➢ Abrasive or harsh cleaners

➢ Metal or plastic-textured

scouring pads

➢ A dishwasher

Textured Doors

and Exterior

Cabinet Interior

Stainless Steel Doors

and Exterior*

IMPORTANT: Damage

to stainless steel finish

due to improper use of

cleaning products or

non-recommended

products is not covered

under this product’s

warranty.

Door Gaskets

Condenser Coil

Remove toe grille to

access

Condenser Fan Outlet

Grille

See back of refrigerator

Accessories Shelves,

buckets, drawers, etc.

To avoid personal injury or property damage, observe the following:

➢ Read and follow manufacturer’s directions for all cleaning products.

➢ DO NOT place buckets, shelves or accessories in dishwasher. Cracking or warp-

ing of accessories may result.

➢ Do not touch refrigerated surfaces with wet or damp hands. Damp objects stick to

cold metal surfaces. Before cleaning the freezer, allow it to warm up. Allow glass

shelves to warm up before immersing in warm water.

CAUTION

To avoid electrical shock which can

cause severe personal injury or death,

disconnect power to refrigerator

before cleaning. After cleaning, con-

nect power.

WARNING

* Cleaner is available for order through your manufacturer. Please contact them, using the information on the front cover of your

User’s Guide, for further ordering information.

Refrigerator Cleaning Chart

CARE & CLEANING

,CONT.

For further assistance, call 1-800-688-9900 U.S.A., 1-800-688-2002 Canada or www.maytag.com

care & cleaning

Removing odors from

refrigerator

➢ Remove all food.

➢ Disconnect refrigerator.

➢ Clean the following items using the

appropriate instructions in the Care

and Cleaning section.

–Walls, floor and ceiling of cabinet

interior.

– Drawers, shelves and gaskets

according to the instructions in this

section.

➢ Pay special attention to clean all

crevices by completing the following

steps:

– Dilute mild detergent and brush

solution into crevices using a plas-

tic bristle brush.

– Let stand for 5 minutes.

– Rinse surfaces with warm water.

Dry surfaces with a soft, clean

cloth.

➢ Wash and dry all bottles, containers

and jars. Discard spoiled or expired

items.

➢ Wrap or store odor-causing foods in

tightly-sealed containers to prevent

reoccurring odors.

➢ Connect power to refrigerator and

return food to unit.

➢ After 24 hours, check if odor has been

eliminated.

If odor is still present:

➢ Remove drawers and place on top

shelf of refrigerator.

➢ Pack refrigerator and freezer sections

– including doors – with crumpled

sheets of black and white newspaper.

➢ Place charcoal briquettes randomly on

crumpled newspaper in both freezer

and refrigerator compartments.

➢ Close doors and let stand 24-48

hours.

NORMAL OPERATING SOUNDS

Improvements in refrigeration design may produce sounds in your new refrigerator that are different or were not present in an older

model. These improvements were made to create a refrigerator that is better at preserving food, more energy efficient, and quieter

overall. Because new refrigerators run quieter, sounds may be detected that were present in older refrigerators, but were masked by

higher sound levels. Many of these sounds are normal. Please note that the surfaces adjacent to a refrigerator, such as hard walls,

floors and cabinetry may make these sounds seem even louder. The following are some of the normal sounds that may be noticed in

a new refrigerator.

SOLUTION

➢ Normal operation

➢ See Installation Instructions for details on how to level

your refrigerator.

➢ Normal operation

➢ Stop sound by raising ice maker arm to ‘off’ position. See

Automatic Ice Maker section on page 11 for details.

➢ Normal operation

POSSIBLE CAUSE

➢ Freezer control (A) clicks when

starting or stopping compressor.

➢ Defrost timer (B) sounds like an

electric clock and snaps in and

out of defrost cycle.

➢ Freezer fan (C) and condenser

fan (D) make this noise while

operating.

➢ Evaporator (E) and heat

exchanger (F) refrigerant makes

this noise when flowing.

➢ Ice cubes from ice maker (some

models) drop into ice bucket (G).

➢ Compressor (H) makes a pul-

sating sound while running.

➢ Refrigerator is not level.

➢ Ice maker water valve (I)

hookup (some models) buzzes

when ice maker fills with water.

➢ Ice maker (J) is in the ‘on’ posi-

tion without water connection.

➢ Compressor (H) can make a high

pitched hum while operating.

➢ Defrost heater (K) hisses,

sizzles, or pops when

operating.

TOPIC

Clicking

Air rushing or whirring

Gurgling or boiling

sound

Thumping

Vibrating noise

Buzzing

Humming

Hissing or popping

For further assistance, call 1-800-688-9900 U.S.A., 1-800-688-2002 Canada or www.maytag.com

operating sounds

BEFORE YOU CALL FOR SERVICE

PROBLEM POSSIBLE CAUSES WHAT TO DO

Freezer control and lights Refrigerator is in defrost mode. Normal operation. Wait 40 minutes to see if refrigerator restarts.

are on, but compressor

is not operating

Refrigerator does not Refrigerator is not plugged in. Plug in unit.

operate

Freezer control is not on. See page 8.

Fuse is blown, or circuit breaker needs Replace blown fuses. Reset circuit breaker.

to be reset.

Power outage has occurred Call local power company listing to report outage.

Refrigerator still won’t Unit is malfunctioning. Unplug refrigerator and transfer food to another refrigerator. If

operate another unit is not available, place dry ice in freezer section to

preserve food. Warranty does not cover food loss.

Contact service for assistance.

Refrigerator has an odor Compartment is dirty or has odor-causing See page 16.

food.

Crisper drawers do not Contents of drawer, or positioning of items Reposition food items and containers.

close freely in the surrounding compartment could be

obstructing drawer.

Drawer is not in proper position. See page 9 for proper crisper placement.

Refrigerator is not level. See page 2.

Drawer channels are dirty or need Clean drawer channels with warm, soapy water. Rinse and dry.

treatment.

Apply a thin layer of petroleum jelly to drawer channels.

Refrigerator runs too Doors have been opened frequently or Minimize door openings.

frequently for long periods of time.

Humidity or heat in surrounding area is Normal operation.

high.

Food has recently been added. Allow time for recently added food to reach refrigerator or

freezer temperature.

Refrigerator is exposed to heat by Evaluate your refrigerator’s environment. Refrigerator may

environment or by appliances nearby. need to be moved to run more efficiently.

Condenser coils are dirty. Clean according to cleaning instructions. See page 14.

Controls need to be adjusted. See page 8.

Door is not closing properly. Refrigerator is not level. See page 2.

Today’s refrigerators start and stop more Check gaskets for proper seal. Clean, if necessary. See page 15.

often to maintain even temperatures.

Check to see if something is preventing door from closing.

Noise, sounds and Normal operation. See page 17.

vibrations

Cabinet not level. Level cabinet. See page 2.

Food temperature Condenser coils are dirty. Clean according to cleaning instructions. See page 14.

is too cold

Refrigerator or freezer controls are set See page 8.

too high.

Food temperature Door is not closing properly. Refrigerator is not level. See page 2.

is too warm

Check gaskets for proper seal. Clean, if necessary. See page 15.

Check to see if something is preventing door from closing.

Controls need to be adjusted. See page 8.

Condenser coils are dirty. Clean according to cleaning instructions. See page 14.

Rear air grille is blocked. Check the positioning of food items in refrigerator to make sure

grille is not blocked. Rear air grilles are located under crisper

drawers.

Prolonged door openings. Minimize door openings.

Review this chart of troubleshooting tips first…you may not need to call for service at all.

GENERAL OPERATION

NOISE

TEMPERATURE

PROBLEM POSSIBLE CAUSES WHAT TO DO

Refrigerator is leaking Plastic tubing was used to complete water Use copper tubing for installation. Plastic is less durable and

water connection. can cause leakage.

Ice forms in inlet tube to Improper water valve was installed. Check water connection procedure in the Installation

ice maker Instructions. Self-piercing and

⁄16" saddle valves cause low

water pressure and may clog the line over time.

Water pressure is low. Water pressure must be between 20 to 100 pounds per square

inch to function properly.

Water flow is slower than Freezer temperature is too high. See page 8. Freezer temperature should be approximately

normal 0° F (-18° C).

Water pressure is low. Water pressure must be between 20 to 100 pounds per square

inch to function properly.

Improper water valve was installed. Check water connection procedure in the Installation

Instructions. Self-piercing and

⁄16" saddle valves cause low

water pressure and may clog the line over time.

Water droplets form on Check gaskets for proper seal. Clean, if necessary. See page 15.

outside of refrigerator

Humidity levels are high. Normal during times of high humidity.

Controls require adjustment. See page 8.

Water droplets form on Humidity levels are high or door has been Minimize door openings.

inside of refrigerator been opened frequently.

Check gaskets for proper seal. Clean, if necessary. See page 15.

ICEMOISTURE

BEFORE YOU CALL FOR SERVICE

, CONT.

La page charge ...

Maytag Bottom freezer refrigerator Manuel utilisateur

Marque: Maytag

Modèle: Bottom freezer refrigerator

Catégorie: Congélateurs

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Maytag Bottom freezer refrigerator User manual
español: Maytag Bottom freezer refrigerator Manual de usuario

Maytag Bottom freezer refrigerator Manuel utilisateur

Maytag Bottom freezer refrigerator Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents