Rheem GHE50SS-100 Mode d'emploi

COMMERCIAL HIGH EFFICIENCY COMMERCIAL HIGH EFFICIENCY

WATER HEATERWATER HEATER

USE & CARE MANUALUSE & CARE MANUAL

AP21836 Rev 02

DO NOT destroy this manual.

Please read carefully and keep in

a safe place for future reference

WARNING

If the information in these

instructions is not followed exactly,

a fire or explosion may result

causing property damage, personal

injury or death.

FOR YOUR SAFETY!

• DO NOT store or use gasoline,

other flammable vapors or liquids

or other combustible materials

in the vicinity of this or any other

appliance. Doing so may result in

a explosion or fire.

-WHAT TO DO IF YOU SMELL GAS

• DO NOT try to light any appliance.

• DO NOT touch any electrical

switch.

• DO NOT use any phone in your

home.

• Immediately call your gas

supplier from a neighbor's phone.

And follow the gas supplier's

instructions.

• If you cannot reach your gas

supplier, call the fire department.

• DO NOT return to your home until

authorized by the gas supplier or

fire department.

-ALWAYS REFER TO THIS MANUAL

• Installation and service must be

performed by a qualified installer,

service agency, or gas supplier.

D

E

S

I

G

N

C

E

R

T

I

F

I

E

D

®

Important Safety Information

General Safety Precautions �� 2–5

Product Information

Components Diagram ��6, 7

Installation

Location ��8

Thermal Expansion �� 9

Water Connections ��9

To Fill the Water Heater ��9

Gas Supply ��10

Leak Testing ��10

Condensate��10

High Altitude �� 11

Wiring ��11

Typical Installation ��12

Space Heating Connections �� 13

Venting and Combustion Air Inlet ��14 - 32

Check List ��33

Operation

Lighting Instructions ��34

Safety Precautions �� 35

User Interface

Start Up �� 36

Temperature Adjustment �� 36

Schedule Settings ��37

Time/Date Settings ��37

WiFi Status ��38

Alarms and Service Alerts ��39

Maintenance

Routine Preventive Maintenance �� 40

Seasonal Operation ��40

Venting System ��40

Before You Call For Service

Troubleshooting Tips �� 41, 42

Error Codes �� 43- 50

Replacement Parts

Instructions For Placing a Parts Order 51, 52

Wiring and Schematic Diagrams ..............................53

How to Obtain Service Assistance ............................ 56

2

CONTENTS

Your safety and the safety of others are very important.

There are many important safety messages in this manual

and on your appliance. Always read and follow all safety

messages.

This is the safety alert symbol. Recognize this

symbol as an indication of importan safety

information! This symbol alerts you to safety

hazards that could result in physical harm or

death.

All safety messages will follow the safety alert symbol and

either the word “DANGER,” “WARNING,” “CAUTION,” or

“NOTICE.”

These words mean:

READ ALL SAFETY INFORMATION

FOR YOUR RECORDS:

Write the model and serial numbers here:

You can find them on a label on the appliance.

Staple sales slip or cancelled check here.

Proof of the original purchase date is needed to obtain service

under the warranty.

DANGER:

NOTICE:

!

CAUTION:

!

WARNING:

An imminently hazardous

situation that will result in

death or serious injury.

A potentially hazardous

situation that can result in

death or serious injury and/or

damage to property.

A potentially hazardous

situation that may result in

minor or moderate injury.

Attention is called to observe a

specified procedure or maintain

a specific condition.

!

3

GENERAL SAFETY PRECAUTIONS

To meet commercial water use needs, the temperature

on this water heater is adjustable up to 185°F (85°C).

However, water temperatures over 125°F (52° C) can cause

severe burns instantly or death from scalds. This is the

preferred starting point for setting the control for supplying

general purpose hot water.

Safety and energy conservation are factors to be

considered when setting the water temperature. The most

energy efficient operation will result when the temperature

setting is the lowest value that satisfies the needs

consistent with the application.

Maximum water temperatures occur just after burner

has shut off. To find the temperature of the hot water

being delivered, turn on a hot water faucet, and place

a thermometer in the hot water stream, and read the

thermometer.

The following chart details the relationship of water

temperature and time to scald injury and may be used as a

guide in determining the safest water temperature for your

applications.

The temperature of the water in the heater can be regulated

by setting the temperature on the display (see "User

Interface" section). To comply with safety regulations the

water heater temperature was adjusted to lowest setting

before the water heater was shipped from the factory. The

illustration information on "User Interface" section shows

the display and how to adjust the water temperature.

DANGER:

Hotter water increases the potential for hot water SCALDS.

NOTICE:

Mixing valves are recommended for reducing point of

use water temperature by mixing hot and cold water in

branch water lines. It is recommended that a mixing valve

complying with the Standard for Temperature Actuated

Mixing Valves for Hot Water Distribution Systems, ASSE

1017 be installed. See Water Connections for more details.

For additional information, contact a licensed plumber or

the local plumbing authority.

DANGER

!

HOT

BURN

Water temperature over 125°F (52°C)

can cause severe burns instantly or

death from scalds.

Children, disabled and elderly persons

are at greatest risk of being scalded.

See instructions manual before setting

temperature of water heater.

Feel water Before bathing or showering.

Temperature limiting valves are

available, see manual.

Water Temperature Time to Produce Serious Burn

120° F (49°C) More than 5 minutes

125° F (52°C) 1

1

/

2

to 2 minutes

130° F (54°C) About 30 seconds

135° F (57°C) About 10 seconds

140° F (60°C) Less than 5 seconds

145° F (63°C) Less than 3 seconds

150° F (66°C) About 1

1

/

2

seconds

155° F (68°C) About 1 second

Table courtesy of Shriners Burn Institute

TIME / TEMPERATURE RELATIONSHIPS IN SCALDS

See Section "User Interface" for setting the temperature�

!

Status: Standby

StatusSettings

warm hot very hot

Disable

120°

Service

4

GENERAL SAFETY PRECAUTIONS

Be sure to read and understand the entire Use and Care Manual before attempting to install or operate this water heater. It may

save you time and money. Pay particular attention to the Safety Instructions. Failure to follow these warnings could result in

serious bodily injury or death. Should you have problems understanding the instructions in this manual, or have any questions,

STOP, and get help from a qualified service technician, or the local gas utility.

Venting:

!

DANGER:

Failure to properly vent the water heater to the outdoors as

outlined in the "Venting and Combustion Air Inlet" section of

this manual can result in unsafe operation of the water heater.

To avoid the risk of fire, explosion, or asphyxiation from carbon

monoxide, never operate this water heater unless it is properly

vented and has adequate air supply for proper operation. Be

sure to inspect the Venting and Combustion Air Inlet section

for proper installation at initial start-up and, at least, annually,

thereafter. Refer to the "Maintenance" section of this manual

for more information regarding vent system inspections.

!

FLAMMABLES

Flammable Vapors

FIRE AND EXPLOSION HAZARD

Can result in serious injury or death.

Do not store or use gasoline or other flammable vapors and liquids

in the vicinity of this or any other appliance. Storage or use of gasoline

or other flammable vapors or liquids in the vicinity of this or any other

appliance can result in serious injury or death.

WARNING

Flammable Materials:

!

WARNING:

Gasoline, as well as other flammable materials and liquids

(which include but are not limited to adhesives, solvents,

paint thinners, etc.), and the vapors they produce are

extremely dangerous. DO NOT handle, use, or store gasoline

or other flammable or combustible materials anywhere near

or in the vicinity of a water heater or any other appliance.

Be sure to read and follow the warning label pictured below

and other labels on the water heater and in this manual.

Failure to do so can result in property damage, bodily injury,

or death.

Natural Gas and Lique-

ﬁed Petroleum Safety

!

DANGER:

LIQUEFIED PETROLEUM MODELS — Propane (LP) gas, must

be used with great caution.

• It is heavier than air and will collect first in lower areas

making it hard to detect at nose level.

• Make sure to look and smell for LP leaks before

attempting ignition of the water heater. Use a soapy

solution to check all gas fittings and connections.

Bubbling at a connection indicates a leak that must be

corrected.

• When smelling to detect an LP leak, be sure to sniff

near the floor too.

• Gas detectors are recommended in LP applications

and their installation should be in accordance with

the manufacturer's recommendations and local laws,

rules, regulations, or customs.

• It is recommended that more than one method be used

to detect leaks in LP applications.

IF LP GAS IS PRESENT OR SUSPECTED:

• DO NOT attempt to find the cause yourself;

• DO NOT try to light any appliance;

• DO NOT touch any electrical switch;

• DO NOT use any phone in your building.

• Leave the building immediately and make sure your

family and pets leave also.

• Leave the doors open for ventilation and contact the

gas supplier, a qualified service agency or the fire

department.

• Stay away from the house (or building) until the

service call has been made, the leak is corrected and

a qualified agency has determined the area to be safe.

!

WARNING:

Both LP and natural gas have an odorant added to help

detection. Some people may not physically be able to smell

or recognize this odorant. If unsure or unfamiliar about

the smell associated with LP or natural gas, ask the gas

supplier. Other conditions, such as "Odorant Fade", which

causes the odorant to "fade" or diminish in intensity can also

hide or camouflage a gas leak.

5

GENERAL SAFETY PRECAUTIONS

!

DANGER:

Water heaters utilizing Liquefied Petroleum gas (LP) are

different from natural gas models. A natural gas heater will

not function safely on LP gas and vice versa. No attempt

should ever be made to convert a heater from natural gas

to LP gas. To avoid possible equipment damage, personal

injury or fire: DO NOT connect this water heater to a fuel

type not in accordance with the unit's data plate. Propane for

propane units; natural gas for natural gas units. These units

are not certified for any other type fuel.

!

WARNING:

LP appliances should not be installed below-grade (for

example, in a basement) if such installation is prohibited by

federal, state, or local laws, rules, regulations or

customs.

Electrical Safety

DANGER:

• Shock Hazard – Make sure the electrical power to the

water heater is off to avoid electric shock that will

result in death or serious personal injury.

WARNINGS:

• For your safety, the information in this manual must

be followed to minimize the risk of fire, explosion, or

electric shock that can result in death, personal injury,

and/or property damage.

• Field wiring connections and electrical grounding must

comply with local codes or, in the absence of local

codes, with the latest edition of the National Electrical

Code, ANSI/NFPA 70, or in Canada, Canadian

Electrical Code, CAN/CSA C22.1, Part 1.

CAUTIONS:

• Label all wires prior to disconnecting for service.

Wiring errors can cause dangerous and improper

operation. Verify correct operation after servicing.\

• For your safety, burner inspection and cleaning should

be performed only by qualified service personnel.

• Make certain the power to the water heater is OFF

before removing the unit cover panel. Exposed

electrical components and moving parts can cause

personal injuries.

• For your safety, DO NOT attempt repair of electrical

wiring, gas piping, remote control, burners, vent

connectors, or other safety devices. Refer repairs to

qualified service personnel.

FOR INSTALLATIONS IN THE

STATE OF CALIFORNIA

California Law requires that all new and replacement

water heaters, and all existing commercial water heaters,

must be braced, anchored, or strapped to resist falling or

horizontal displacement due to earthquake motion. At a

minimum, any water heater shall be secured in accordance

with the California Plumbing Code, or modifications made

thereto by a city, county, or city and county pursuant to

Section 17958.5. Generic instructions for California titled

“Guidelines for Earthquake Bracing Commercial Water

Heaters” can be obtained by:

• Writing the California, Department of General Services,

Division of State Architect, 1102 Q Street, Suite 5100,

Sacramento, CA 95814

• Calling (916) 445-8100

• Following web address:

https://www�dgs�ca�gov/-/media/Divisions/DSA/Publications/

gas_shutoff/waterheaterbracing

Inspect Shipment

Carefully inspect the water heater for damage before

proceeding with the installation. Of specific interest should

be combustion air-inlet piping assembly, exhaust-tee, or

damage to blower-valve assembly. If you find damage,

DO NOT install or attempt any repair to the water heater.

Contact the manufacturer as detailed under "HOW TO OBTAIN

ASSISTANCE".

6

COMPONENTS DIAGRAM (50 GAL)

Touch Display

Jacket

Leak Sensor

Side Outlet

Power Anodes

Side Inlet

Power Anode

Temperature

and Pressure

Relief Valve

Drain Valve

Leak Sensor

Exhaust

Tee Assy

Pressure

Switch

(Intake)

Anode

Module

Front Panel

Assy

Blower

Side Panel

Air Intake

Ignition

Control

Pressure Switch

Proof of Fan

Exhaust

Tee Assy

Transformer Box

Gas Inlet

Lower

Thermistor

Front View

Top View

Back Iso View

Status: Standby

StatusSettings

warm hot very hot

Disable

120°

Service

7

COMPONENTS DIAGRAM (75 GAL)

Jacket

Leak Sensor

Side Outlet

Power Anode

Side Inlet

Power Anode

Power

Anode

Temperature

and Pressure

Relief Valve

Upper

Thermistor

Drain Valve

Leak Sensor

Exhaust

Tee Assy

Anode

Module

Pressure

Switch

(Intake)

Front Panel

Assy

Blower

Side Panel

Air Intake

Pressure Switch

Proof of Fan

Ignition Control

Exhaust

Tee Assy

Transformer Box

Gas Inlet

Lower

Thermistor

Front View

Touch Display

Top View Back Iso View

Status: Standby

StatusSettings

warm hot very hot

Disable

120°

Service

8

INSTALLATION

Location

This water heater must be installed in accordance with these instructions, local codes, utility company requirements, and/or in

the absence of local codes, use the latest edition of the American National Standard/National Fuel Gas Code for US and CAN/CSA

B149 - Natural Gas and Propane Installation Code for Canada. A copy can be purchased from the American Gas Association, 400N.

Capitol Street NW, Washington, DC 20001 as ANSI standard C223.1 or National Fire Protection Association, 1 Batterymarch Park,

Quincy, MA 02269 as booklet NFPA 54. for US and Canadian Standards Association, 5060 Spectrum Way, Mississauga, Ontario

L4W5N6 for Canada.

The water heater should not be located in an area where

leakage from the tank or connections will result in damage

to the area adjacent to the heater or to lower floors of the

structure.

When such areas cannot be avoided it is recommended that a

suitable drain pan, adequately drained, must be installed under

the water heater.

The auxiliary drain pan installation MUST conform with local

codes.

The water heater must be positioned in the drain pan as shown.

Ensure that the condensate-tee is located inside the drain pan.

The recommended minimum drain pan sizes are 28" diameter

for 50Gal and 32" diameter for 75Gal water heaters

Drain pan kits are available from the store where the water

heater was purchased, or any water heater distributor.

Make certain the floor underneath the water heater is strong

enough to sufficiently support the weight of the water heater

once it is filled with water.

This gas-fired water heater or any other appliance should not

be installed in a space where liquids which give off flammable

vapors are to be used or stored. Such liquids include gasoline,

LP gas (butane or propane), paint or adhesives, thinners,

solvents and/or combustible removers.

WARNING:

Because of natural air movement in a room or other enclosed

space, flammable vapors can be carried some distance from

where liquids which give off flammable vapors are to be used

or stored. The open flame of the water heater’s main burner

can ignite these vapors creating a shut down condition which

will not allow the water heater to ignite.

Rheem Water Heating FVIR certified gas water heaters can

be installed on a residential garage floor without the use of

an 18 in. (46 cm.) stand in accordance with the National Fuel

Gas Code, ANSI Z223.1/NFPA 54, unless otherwise directed by

State and Local code requirements. The water heater must be

located so it is not subject to physical damage, for example,

by moving vehicles, area flooding, etc.

IMPORTANT: DO NOT install the water heater in a location

where it may be subjected to ambient temperatures exceeding

125°F (52°C).

• The water heater should be installed so as to minimize the

length of plastic vent and combustion air-inlet pipe and the

number of vent and combustion air-inlet connection fittings

required.

• See Vent and Combustion Air-Inlet Section for vent system

requirements.

• Hot water lines should be insulated to conserve water and

energy.

• Protect the water heater and water lines from exposure to

freezing temperatures.

• DO NOT install this water heater outdoors.

• Minimum clearances from combustible construction:

Front Sides Rear Top

5 In.

(12.7 cm)

0 In.

(0 cm)

0 In.

(0 cm)

15 In.

(30.5 cm)

The Exhaust Tee located on the right front of the unit will require additional side

clearance of approximately 2.75" from the water heater.

"Front" Clearance dimension is measured from the water heater

jacket to the closet door.

"Top" clearance dimension is measured from the jacket top of

the water heater to the ceiling.

NOTICE:

For proper operation and maintenance, a minimum

clearance of 1.5 inches (3.8 cm) must be provided from

the combination temperature and pressure relief valve to

any wall or object.

WARNING:

Combustible construction refers to adjacent walls and

ceilings and should not be confused with combustible or

flammable products and materials. Combustible and/or

flammable products and materials should never be stored in

the vicinity of this or any gas appliance.

DRAIN PAN

9

INSTALLATION

If the water heater is to be installed directly on carpeting,

the water heater shall be installed on a metal or wood

panel extending beyond the full width and depth of the

water heater by at least 3 in. (7.6 cm) in all directions

or, if the water heater is to be installed in an alcove or

closet, the entire floor must be covered by a wood or

metal panel.

CORROSIVE ATMOSPHERES

The air in beauty shops, dry cleaning establishments,

photo processing labs, and storage areas for liquid and

powdered bleaches or swimming pool chemicals often

contain halogenated hydrocarbons.

An air supply containing halogenated hydrocarbons may

be safe to breathe, but when it passes through a gas

flame corrosive elements are released that will shorten

the life of any gas burning appliance.

Propellants from common spray cans or gas leaks from

A/C and refrigeration equipment are highly corrosive

after passing through a flame.

The water heater warranty is voided when failure of the

heater is due to operation in a corrosive atmosphere.

THERMAL EXPANSION

Determine if a check valve exists in the inlet water line.

It may have been installed in the cold water line as

a separate back flow preventer, or it may be part of a

pressure reducing valve, water meter or water softener.

A check valve located in the cold water inlet line can

cause what is referred to as a ”closed water system”.

A cold water inlet line with no check valve or back flow

prevention device is referred to as an ”open” water

system.

As water is heated, it expands in volume and creates

an increase in the pressure within the water system.

This action is referred to as ”thermal expansion”. In an

”open” water system, expanding water, which exceeds

the capacity of the water heater, flows back into the city

main where the pressure is easily dissipated.

A ”closed water system”, however, prevents the

expanding water from flowing back into the main supply

line and the result of ”thermal expansion” can create

a rapid, and dangerous pressure increase in the water

heater and system piping. This rapid pressure increase

can quickly reach the safety setting of the relief valve,

causing it to operate during each heating cycle. Thermal

expansion, and the resulting rapid, repeated expansion

and contraction of components in the water heater and

piping system can cause premature failure of the relief

valve and possibly the heater itself. Replacing the relief

valve will not correct the problem!

The suggested method of controlling thermal expansion

is to install an expansion tank in the cold water line

between the water heater and the check valve. The

expansion tank is designed with an air cushion built

in that compresses as the system pressure increases,

thereby relieving the over pressure condition and

eliminating the repeated operation of the relief valve.

Other methods of controlling thermal expansion are

also available. Contact your installing contractor, water

supplier, or plumbing inspector for additional information

regarding this subject.

WATER CONNECTIONS

Refer to illustration on page 12 for suggested typical

installation. The installation of unions or flexible

connectors is recommended on the hot and cold water

connections so that the water heater may be easily

disconnected for servicing if necessary. If flexible water

connections are used, they must comply with the standard

for flexible Water Connectors, ASME A112.18.6/CSA-

B125.6. The HOT and COLD water connections are clearly

marked on the water heater. Install a shutoff valve in the

cold water line near the water heater.

IMPORTANT

All models are equipped with front and side panels, it is

recommended that the hot and cold water piping have a

minimum vertical height of 10 inches (25.4 cm) from the

top of the water heater before transitioning into any elbow.

This vertical height is needed in order to provide adequate

clearance for Side Panel installation and removal.

To gain access to the hot and cold water connections

the side panels need to be removed. The side panels are

secured on the top of the water heater with fastening

pegs (see illustration). Pull the side panels either

outwards or upwards to release panels from pegs.

RELIEF VALVE

The pressure rating of the relief valve must not exceed

150 psi (1,034 kPa), the maximum working pressure of the

water heater as marked on the rating plate.

The Btu/h rating of the relief valve must equal or exceed

the Btu/h input of the water heater as marked on its rating

plate.

Position the outlet of the relief valve above a suitable open

drain to eliminate potential water damage. Piping used

should be of a type approved for hot water distribution.

The discharge line must be no smaller than the outlet of

the valve and must pitch downward from the valve to allow

complete drainage (by gravity) of the relief valve and

discharge line.

The end of the discharge line should not be threaded or

concealed and should be protected from freezing. No valve

of any type, restriction, or reducer coupling should be

installed in the discharge line.

TO FILL THE WATER HEATER

Make certain that the drain valve is closed, then open the

shut-off valve in the cold water supply line.

Open each hot water faucet slowly to allow the air to vent

10

from the water heater and piping.

A steady flow of water from the hot water faucet(s)

indicates a full water heater.

GAS SUPPLY

The inlet gas pressure to the water heater must not

exceed 10.5" wc (2.6 kPa) for Natural gas and 13.0" wc

(3.2 kPa) for L.P. gas. The minimum inlet gas pressure

(with main burner on) is shown on the rating plate.

Check to see if high or low gas pressure is present and

then contact the gas company for correction.

The branch gas supply line to the water heater should

be clean properly sized steel pipe or other approved gas

piping material.

A union or ANSI design certified semirigid or flexible

gas appliance connector should be installed in the gas

line close to the water heater. The National Fuel Gas

Code (NFGC) mandates a manual gas shut off valve: See

(NFCG) for complete instructions.

If flexible connectors are used, the maximum length

shall not exceed 36 in. and must meet the requirements

in ANSI Z21.24/CSA 6.10 - Connectors for Gas

Appliances.

Compound used on the threaded joints of the gas piping

must be of the type resistant to the action of LP gas. Use

compound sparingly on male threads only.

Where a sediment trap is not incorporated as part

of the appliance, a sediment trap shall be installed

downstream of the equipment shutoff valve as close to

the inlet of the appliance as practical at the time of the

appliance installation. The sediment trap shall be either

a tee fitting with a capped nipple in the bottom outlet or

other device recognized as an effective sediment trap.

See Figure.

DO NOT use excessive force (20Ft. Lbs.) in tightening

the pipe joint at the gas control (thermostat) inlet,

particularly if teflon pipe compound is used, as the valve

body may be damaged.

For purposes of input adjustment, the minimum inlet

gas pressure (with main burner on) is shown on the

water heater rating plate. If high or low gas pressure are

present, contact your gas supplier for correction.

A ground joint union and manual shutoff valve should

be installed in the gas line near the water heater so

that the burner assembly may be easily removed. The

shut-off valve must be readily accessible for turning on

or off.

LEAK TESTING

The water heater and its gas connections MUST be leak

tested at normal operating pressure before it is placed

in operation. Turn ON the manual gas shut-off valve

near the water heater. Use a soapy water solution to test

for gas leaks at all connections and fittings. Bubbles

indicate a gas leak that must be corrected. The water

INSTALLATION

heater factory connections to the gas valve should

also be leak tested after placing the water heater in

operation.

!

WARNING:

NEVER use open flame to test for gas leaks, as bodily

injury or property damage could result.

PRESSURE TESTING THE GAS SUPPLY SYSTEM

The water heater and its individual gas shut-off valve

MUST be disconnected from the gas supply piping

system during any high pressure testing of that system

at pressures in excess of 1/2 psi (14” WC. 3.5 kPa).

The water heater MUST be isolated from the gas

piping system by closing the manual gas shut-off valve

during any pressure testing of the gas supply piping at

pressures equal to or less than 1/2 psi (14” WC / 3.5

kPa).

CONDENSATE

The exhaust elbow/condensate trap is shipped pre-installed

with the heater. Pour the neutralizer into the exhaust tee

before vent pipe installation. Make sure that the neutralizer

is at the bottom as shown in the figure on next page.

This is a condensing high efficiency appliance and has a

condensate removal system. The exhaust tee incorporates

a condensate trap and must be filled with water before

operating the water heater. Pour about 1 cup of water into

the exhaust tee.

This water heater generates condensate and requires a

drain to be located in close proximity to allow condensate to

drain safely. The drain line and fittings should be installed

per installation instructions.

Be sure the condensate runs freely to the drain and does

not accumulate in the condensate trap or the condensate

line. In cold climates, precautions may need to be taken

to ensure that the condensate drain lines do not freeze. A

water proof heat tape may be used to prevent freezing of

condensate lines.

To Gas Supply

Manual Gas Shut Off

Gas Pipe to Gas Valve

Sediment

Trap

Union

11

• Condensate is mildly acidic and should be collected and

disposed per local codes. Certain local codes require

condensate to be neutralized before it is disposed. This

water heater comes with a pre-packaged neutralizer bag.

Pour the neutralizer in the exhaust-tee prior to installing

vent pipes. Make sure the neutralizer is at the bottom of the

exhaust-tee.

• Use only PVC, CPVC pipe or flexible tubing suitable for use

with flue condensate as drain line. If flexible tubing is used

ensure that there are no bends or twists and has gradual

slope to condensate drain.

• The drain line (along its entire length) must be at least the

same diameter as the drain of the condensate trap (1/2”).

• The drain line must be short as possible and have a

downward slope towards the condensate drain. If suitable

slope is not provided, the drain line can get blocked and

will cause improper operation of the water heater. If a

downward slope cannot be provided, a condensate pump

should be used to pump condensate to a suitable drain.

• The end of the drain line should be open to the atmosphere.

The end should not be under water.

• DO NOT connect the drain line directly to the sewer drain.

• DO NOT connect the drain line with drains from other

appliances.

• DO NOT drain condensate into the water heater drain pan.

• DO NOT drain condensate over public way, walkway or other

areas where it will create slippery condition, which could

lead to personal injury.

HIGH ALTITUDE

Input rating of this water heater is based on sea level

operation. At higher elevations the actual input rate may

be lower than the value listed on the rating label due to

the derating of Natural Gas and LP Gas.

!

WARNING:

Failure to install a water heater suitable for the altitude

at the location it is intended to serve, can result in

improper operation of the appliance resulting in property

damage and/or producing carbon monoxide gas, which

could result in personal injury, or death.

WIRING

A Correct polarity 120V 50/60 Hz power supply with

suitable disconnect means, must be connected to the

black and white leads provided. The maximum current

draw by these models is 7 Amps. The water heater, when

installed, must be electrically grounded in accordance

with local codes or, in the absence of local codes, with

the National Electrical Code, ANSI/NFPA 70 in the United

States, or CSA C22.1 Electrical Code, in Canada. Improper

grounding or polarity may result in abnormal operation of

the heater.

INSTALLATION

CONDENSATE

NEUTRALIZER

CONDENSATE

DRAIN

To open drain

Transformer

(120V / 60Hz)

F

FFM

M

F

To Ground Block

3

2

1

3

2

1

3

2

1

F

To Ground Block

F

M

F

M

Power Cord

Display Rocker Switch

on the front display

C1

Blower Power Connector

C2

Ignition Control Power

Connector

C3

M

F2-520263-2

Disconnect

2-520102-2

Disconnect

Transformer

(120V / 60Hz)

F

FFM

M

F

To Ground Block

3

2

1

3

2

1

3

2

1

F

To Ground Block

F

M

F

M

Power Cord

Display Rocker Switch

on the front display

C1

Blower Power Connector

C2

Ignition Control Power

Connector

C3

M

F2-520263-2

Disconnect

2-520102-2

Disconnect

For Commercial applications disconnects

can be cut off and replaced with wire nuts to

connect the leads to the power cable from

the electrical junction box if necessary.

12

To Gas Supply

Manual Gas Shut Off

Drain Valve

Union

Thermal Expansion Tank

(Not Supplied)

If required, install per

local codes and tank

manufacturer's instructions.

Too cold

water

supply

Vacuum Relief Valve (Not supplied)

If required, install per local codes and

valve manufacturer's instructions

Heat Trap

6" Minimum

Heat Trap

6" Minimum

Shut-off

Valve

Shut-off

Valve

Sediment Trap

Temperature & Pressure

Relief Valve

Discharge Line to

suitable open drain

Air Gap 6"

NOTES:

The gas supply piping

must be adequately

supported and aligned to

minimize loads (forces)

on the water heater's gas

valve and burner system.

Hot water

outlet to

ﬁxtures

TYPICAL INSTALLATION

INSTALLATION

3/4" Check Valve

with 1/8" Hole

Pressure Gauge

Hot water line

Cold water line

3/4" Shut-Off

Valve (Typ.)

Gas Line

3/4" cold water

supply

Heat Trap

6” Min. 3/4" Shut-Off

Valve (Typ.)

2 Gallon Thermal Expansion

Tank (if required-not supplied

with water heater)

3/4" Shut-

Off Valve

(Typ.)

3/4" Tempered

domestic hot water

supply to house.

Minimum of 2'-0" developed length

of 3/4" type "L" copper from the

water heater connection.

Nominal 3/4" size mixing or

tempering valve (refer to warning

above). Follow mixing or tempering

valve manufacturer’s instructions

for installation of the valve.

Isolation valve in hot water

supply line to heating unit (not

supplied with water heater)

See diagrams above for proper

pipe application for vertical

or horizontal supply lines.

Temperature and Pressure Relief

Valve, tie to location approved by

local code

Temperature and pressure

relief valve discharge line

140°F (60°C)

120°F (49°C) to

130°F (54°C)

Water Heater drain pan installed

in accordance with the Local and

State Code

6” Air Gap

Isolation valve in

cold water return

line from heating

unit (not supplied

with water heater)

Drain valve

(not supplied

with water

heater)

Air vent

3/4" HWS & HWR

to Heating Coil.

Water Heater drain pan installed

in accordance with the Local

and State Code

Air Handler

T FAN

ON

OFF

HEAT

COOL

To HVAC Unit.

Piping loop between

water heater and fan

coil shall be ﬂow guard

gold CPVC or equal

Hot water to

space heater

Hot water coil

All bronze pump

Check valve internal

in pump

Air bleed valve

Water Sample Tap

Flow Control

Valve

13

TYPICAL PIPING DIAGRAM FOR COMBINATION POTABLE/SPACE HEATING INSTALLATION’

INSTALLATION

14

INSTALLATION

VENT AND COMBUSTION AIR INLET

NOTE: This unit can be vented either as a direct vent or power

vent configuration.

NOTE: Power vent installations are Category IV.

!

WARNING:

DO NOT connect this water heater to an existing vent

or chimney; it must be vented separately from all other

appliances, using only approved venting materials.

!

WARNING:

Failure to properly vent the water heater to the outdoors as

outlined above and in the following section can result in

unsafe operation of the water heater causing bodily injury,

explosion, fire or death.

!

DANGER:

To avoid the risk of fire, explosion, or asphyxiation from

carbon monoxide, NEVER operate the water heater unless

it is properly vented and the vent and combustion air inlet

systems are properly installed as detailed in the "Vent and

Combustion Air-Inlet" section of this manual.

The vent and combustion air inlet pipes must overlap a

minimum of 1/2 in. (1.3 cm) at each joint. It is important that

the vent and combustion air inlet pipes engage fully into any

pipe fitting and be kept in that position until the adhesive has

fully cured. DO NOT drill or punch holes in the plastic pipe or

fittings.

IMPORTANT

Where state and/or local codes require vent terminations,

as specified in this Use and Care Manual to be certified

to the UL 1738 Standard for Venting Systems for Gas-

Burning Appliances, Categories II, III, and IV, contact the

Manufacturer’s National Service Department (see page 52).

NOTICE:

This unit can be vented using only the below

recommended pipe material. Use only 2, 3, or 4 inch

diameter pipe.

Refer to local codes for restrictions on the use of PVC,

CPVC, PP or ABS pipe and fittings. All exhaust venting

materials for products installed in Canada must meet ULC-

S636.

NOTE: For the State of Massachusetts, use only plastic

piping, fittings and vent terminations as spedified in the

manual which are approved by the Massachusetts Board

of State Examiner of Plumbers and Gas for venting of

appliances (see link below):

https://licensing.reg.state.ma.us/pubLic/pl_products/

pb_pre_form.asp

PVC (DWV, ASTM-D2665 or CSA B181.2)

PVC (Schedule 40, ASTM-D1785 or CSA B137.3)

PVC (SDR Series, ASTM-D2241 or CSA B137.3)

CPVC (CPVC 4120, ASTM-D2846 or CSA B137.6)

CPVC (Schedule 40, ASTM-F441 or CSA B137.3)

CPVC (SDR Series, ASTM-F442)

ABS (Schedule 40, DWV, ASTM-D2661 or CSA B181.1)

ABS (Schedule 40, DWV, Cellular Core, ASTM-F628)

Polypropylene

15

NOTICE:

Use of PVC cellular core (ASTM-F891), ABS Schedule 40, DWV

cellular core (ASTM –F628), or Radel® (polyphenylsulfone) in

non-metallic venting systems is prohibited.

The unit may be vented horizontally through a wall or vertically

through the roof. Pipe runs must be adequately supported along

both vertical and horizontal runs. Maximum unsupported span

is recommended to be no more than 3 feet. It is imperative that

the first hanger be located on the horizontal run immediately

adjacent to the first 90-degree elbow from the vertical rise or

at the blower outlet. The support method used should isolate

the vent pipe from floor joists or other structural members to

help prevent the transmission of noise and vibration. DO NOT

support, pin, or otherwise secure the venting system in a way

that restricts the normal thermal expansion and contraction of

the chosen venting material.

If the water heater is being installed as a replacement for an

existing power vented or power direct vented water heater, a

thorough inspection of the existing venting system must be

performed prior to any installation work. Verify that the correct

materials, as detailed above, have been used and that the

minimum or maximum vent length and terminal locations,

as detailed in this manual, have been met. Carefully inspect

the entire venting system for any signs of cracks or fractures,

particularly at the joints between elbows or other fittings and the

straight runs of vent pipe. Check the system for signs of sagging

or other stresses in the joints as a result of misalignment of

any components in the system. If any of these conditions are

found, they must be corrected in accordance with the venting

instructions in this manual before completing the installation and

putting the water heater into service.

Additional installation information for The Common wealth of

Massachusetts is located on the back page of this manual.

VENT PIPE CONNECTION

Refer to "Vent Pipe Connection Locations" Figure, for connecting

the vent pipe to the water heater. These models can be vented

either as a direct vent or as a power vent water heater.

NOTICE:

If the unit is installed as a power vent water heater, the vent

terminal with screen must still be installed on the inlet air side.

INSTALLATION

Before starting the vent installation, careful planning of

the routing and termination of vent and air inlet pipes can

reduce installation times. The length of the vent and air inlet

pipes should be kept to a minimum. Refer to the venting

charts in Table 1 for the pipe sizes and the total equivalent

length of pipe that can be used. DO NOT exceed the

equivalent length of pipe in the charts.

Depending on the size of pipe selected for venting the water

heater, it may be necessary to use a fitting for stepping up

to connect to the water heater. DO NOT step down pipe size

below the 2" pipe size. All models are shipped with 2" vent

terminals with screen. If another size of pipe is used for

venting the unit, the proper vent terminal must be installed.

When the unit is vented as a direct vent, through a side

wall, the vent terminals must be on the same exterior wall

mounted horizontally and maintain a minimum distance

between the centers of 15" (38.1 cm).

JOINING PIPES AND

FITTINGS

All pipe, fittings, solvent cement, primers, and procedures,

must conform to American National Standards Institute and

American Society for Testing and Materials (ANSI/ASTM)

standards in the U.S. For Canada, all pipe, fittings, solvent

cement, primers, and procedures must conform to ULC-

S636 and vent manufacture specifications.

CEMENTING JOINTS

NOTICE:

All pipe, fittings, solvent cement, primers and procedures

must conform to American National Standards Institute and

American Society for Testing and Materials (ANSI/ASTM)

standards.

All joints in the vent piping must be properly sealed. Use of

the following material is recommended:

PVC materials should use ASTM D-2564 grade cement.

CPVC materials should use ASTM F-493 grade cement.

ABS materials should use ASTM D-2235 grade cement.

(ABS is not allowed in Canada)

Cleaner-Primer and Medium Body Solvent Cement

1. Cut the pipe end square, removing all jagged edges and

burrs. Chamfer the end of the pipe, and, then, clean

the fitting socket and pipe joint area to remove all dirt,

grease, and moisture.

2. After checking pipe and socket for proper fit, wipe the

socket and pipe with cleaner-primer. Apply a liberal

coat of primer to the inside surface of the socket and

the outside of the pipe. DO NOT allow the primer to dry

before applying the cement.

Blower Air Inlet

Connection

Noise

Reducer

VENT PIPE CONNECTION LOCATIONS

16

INSTALLATION

3. Apply a thin coat of cement evenly in the socket. Quickly

apply a heavy coat to the pipe end. Insert the pipe into the

fitting with a slight twisting motion until it bottoms out.

NOTICE:

Cement must be fluid; if not, re-coat.

4. Hold the pipe fitting for 30 seconds to prevent the tapered

socket from pushing the pipe out of the fitting.

5. Wipe all excess cement from the joint with a rag. Allow

15 minutes for drying before handling. Cure time will vary

according to fit, temperature, and humidity.

NOTICE:

Stir the solvent cement frequently while using. Use a natural

bristle brush or the dauber supplied with the can. The proper

brush size is one inch.

FOR PROPER

INSTALLATION

CAUTIONS:

• DO NOT use solvent cement that has become curdled,

lumpy or thickened.

• DO NOT thin solvent cement. Observe shelf

precautions printed on the containers.

• For applications below 32°F (0°C), use only low

temperature type solvent cement.

• Appropriate solvent and cleaner must be used for the

type of vent pipe used (PVC, CPVC, PP, or ABS).

DANGER OF FIRE OR

BODILY INJURY

Solvent cements and primers are highly flammable. Provide

adequate ventilation and do not assemble near a heat source

or open flame. DO NOT smoke. Avoid skin or eye contact.

Observe all cautions and warnings on material containers.

Additional Fitting Considerations

10 Feet Equivalent

length 8 Feet Equivalent

Length 5 Feet Equivalent

Length

Short Sweep 90°

Elbow Standard 90°

Elbow Long Sweep 90°

Elbow

EXAMPLES OF ELBOWS:

It is recommended to

use only standard and/or

long sweep elbows. See

examples as shown.

Minimum and Maximum Vent Lengths

Important information for all installations:

1) The minimum required venting is what is required to safely extend the inlet and outlet vent pipes

outside of the building.

2) Each 90° elbow (standard or long sweep elbow) reduces the

equivalent vent length as shown.

3) Each 45° elbow reduces the equivalent vent length by 2 1/2 feet (0.8m).

4) DO NOT mix pipe sizes for venting these models, use only one size of pipe for all venting.

5) All vent terminations (horizontal or vertical) should be a minimum of 24 inches (61cm) and a

maximum of 36 inches (91 cm) apart, as measured from center to center of terminals.

Exceeding the maximum equivalent vent lengths may cause the water heater to malfunction or cause a

lock-out condition.

Feet to Meters

20 6.1

50 15.2

60 18.3

70 21.3

80 24.4

100 30.5

120 36.6

130 39.6

170 51.8

17

INSTALLATION

NOTE: The intake and exhaust connections are set-up with 2" Schedule 40 pipe size. An adapter may be used to increase pipe size

to 3" and 4" along the length of the vent and air intake. Vent and air intake pipes should always be set-up to the same size. The vent

length calculations should be based upon termination size.

Follow manufacturers instructions for installation of flex

vents.

All power direct models can use 2 in. concentric venting only as listed

in the above chart.

2 inch concentric vent can only be used with 2 inch rigid piping.

DO NOT mismatch concentric vent terminations with different rigid

piping as it may cause the heater to malfunction or cause a lock-out

condition unless specifically mentioned.

3" Concentric vent may be used with 3" and 4" venting.

Flexible Polypropylene pipe (ft)

Pipe Size (IN.) 2" 3"

Intake Exhaust Intake Exhaust

Max PV 030'

(13m) 030'

(13m)

Commercial Equivalent Vent Lengths

50G-76K, 50G-100K, 75G; POWER VENT

CONFIGURATION; (RIGID PIPE)

50G-76K, 50G-100K, 75G; POWER DIRECT VENT

CONFIGURATION; (RIGID PIPE)

Elevation

(Feet)

Vent Size

(Inches)

Nat Max Eq.

Length (Feet)

LP Max Eq.

Length (Feet)

Nat Max Eq. Length(Feet) LP Max Eq. Length (Feet)

Terminations

Intake Exhaust Intake Exhaust

0-10,100

2" 40' 40' 40' 40' 40' 40' 2" AND 3"

90° ELBOWS,

2", 3" AND 4"

CONCENTRIC

AND 2"AND 3"

PANCAKE

3" 140' 140' 140' 140' 140' 140'

4" 140' 140' 140' 140' 140' 140'

MINIMUM INTAKE AIR AND EXHAUST VENT: 10' EQUIVALENT LENGTH

18

INSTALLATION

Direct Vent Installation

Check to make sure flue gases DO NOT recirculate into the

air intake terminal when using direct venting. If the water

heater is having service issues, flue recirculation may be a

contributing factor.

Even when the minimum vent terminal separation distances

are followed, recirculation may still occur, depending upon

the location outside the building, the distance from other

buildings, proximity to corners, weather conditions, wind

patterns, and snow depth.

Periodically check to make sure that flue recirculation is not

occurring. Signs of flue gas recirculation include frosted or

frozen intake terminals, condensate in the intake terminal

and venting system, oxidation, or white chalk material

on the flame sensor or igniter shield. Correction to flue

recirculation may involve angling the intake away from the

exhaust terminal, increasing the distance between them, or

using inside air for combustion. Check to be sure the intake

and exhaust terminals are not obstructed, especially during

periods of below freezing weather.

All intake and exhaust venting components must have the

same diameter size. DO NOT use a different size on the

intake and exhaust venting.

Be sure the condensate runs freely to a drain and does

not accumulate inside the water heater. In cold climates,

precautions may need to be taken to insure that the

condensate drain does not freeze. Make sure the condensate

trap or drain loop is installed to prevent flue gases from

being discharged into the room. Refer to the "Venting" section

of this manual for complete instructions on venting and

condensate drainage.

Stress levels in the pipe and fittings can be significantly

increased by improper installation. If rigid pipe clamps are

used to hold the pipe in place, or if the pipe cannot move

freely through a wall penetration, the pipe may be directly

stressed, or high thermal stresses may be formed when the

pipe heats up and expands. Install accordingly to minimize

such stresses. Follow the below procedure to vent through the

wall.

1. Cut two holes for the pipe to pass through. The hole

diameter should be 2.5" (6.4 cm) for 2" pipe, 3.5" (8.9

cm) for 3" pipe. Vent terminals must maintain a horizontal

distance apart in the range of 24" min. (61 cm).

2. Use the proper PVC cement (primer and adhesive) to

secure the exhaust vent and air intake terminals provided

with the water heater to the plastic pipes. The distance

between the back edge of the exhaust vent terminal and

the exterior wall must be 6 inches (12.7 cm) more for the

exhaust vent terminal than the air intake terminal. Use

the proper cement or sealant and assembly procedures to

secure the vent connector joints between the terminal and

the blower outlet. Provide support brackets every 3 feet

(.91 m) of horizontal vent beyond the intake terminal.

19

Min. 24"

Inlet Outlet

Additional considerations in the following pages.

DO NOT install vent terminals under any patio or deck.

To help prevent moisture from freezing on walls and under

eaves, DO NOT locate outlet vent terminal on the side of your

home with prevailing winter winds.

DO NOT terminate vent pipe directly on brick or masonry

surfaces. Use a rust-resistant sheet metal backing plate behind

vent. (See Figure above.)

DO NOT locate vent terminal too close to shrubbery, since flue

gases may damage them.

Caulk all cracks, seams and joints within 6 feet

(1.83 m) of vent terminal.

All painted surfaces should be primed to lessen the chance of

physical damage. Painted surfaces will require maintenance.

Make sure that all vent pipes exposed to cold conditions

(attics, crawl spaces, etc.) have the proper slope and support

to keep moisture from accumulating in the vent pipes. NOTE:

Insulating of non-metallic vent materials is prohibited.

This water heater requires its own separate venting system.

DO NOT connect the exhaust vent to an existing vent pipe or

chimney.

Moisture in the flue gas will condense as it leaves the vent

terminal. In cold weather this condensate can freeze on the

exterior wall, under the eaves, and on surrounding objects.

Some discoloration to the exterior of the building is to be

expected; however, improper location or installation can result

TYPICAL HORIZONTAL VENT INSTALLATION

VERTICAL VENT TERMINAL LOCATION

Short Piece of Vent

Pipe

*Min. 12"(30.5 cm)

Above Roof or

Min. 12"(30.5 cm) Above

Anticipated Snow Level.

Max. 24"(61 cm) Above

Roof (Without Additional

Support)

Vent Pipe

Through

Roof

Elbows

* Min of 18"(46 cm) for Canada

Pipe &

Coupling

Sheet Metal Shield on

Brick or Masonry Walls

Outside of the

Building Wall

To the Water Heater

Vent Pipe

Inlet Vent Terminal

with 1/2" Mesh

Protective

Screen Inside

Vent

Pipe

Elbow can be a maximum

of 1 inch from the wall.

in severe damage to the structure or exterior finish of the

building. In locations with extended amounts of time with

temperatures under 40°F. (4°C.) and/or prevailing wind toward

the outlet vent, make sure that the outlet vent terminal is at

least 2 feet (0.61 m) away from anything that can be damaged

by the condensate.

HORIZONTAL VENT

INSTALLATION

Once the vent terminal location has been determined, make a

hole through the exterior wall to accommodate the vent pipe.

The vent pipe must exit the exterior wall horizontally only (See

Typical Horizontal Vent Installation Figure on this page).

Insert a small length of vent pipe through the wall, and

connect the coupling as shown in Typical Horizontal Vent

Installation Figure. Connect the vent terminal as shown to the

vent pipe on the exterior of the building. Seal any opening

around the vent pipe or fittings with mortar or silicone caulk

as shown in Typical Horizontal Vent Installation Figure.

Complete the rest of the vent pipe installation to the water

heater’s vent connector fitting on the blower outlet. If

necessary, support the horizontal run of pipe as previously

mentioned.

VERTICAL VENT

INSTALLATION

Once the vent terminal location has been determined, make

a hole through the roof and interior ceiling to accommodate

the vent pipe. Complete the vent pipe installation to the water

heater’s vent connector fitting on the blower outlet. Support

vertical or horizontal runs as previously mentioned.

Install adequate flashing where the vent pipe passes through

the roof. Determine the vent terminal height and cut the vent

pipe accordingly. Refer to Vertical Vent Terminal Location

Figure for the proper vent terminal height. Connect the vent

elbow onto the vertical pipe through the roof. Connect a short

piece of vent pipe (approximately 3" (7.6 cm) long) to the

elbow, and, then, join the vent terminal to the short piece of

vent pipe.

INSTALLATION

20

D

V

E

FIXED

CLOSED

O

P

ERABL

E

O

PE

R

A

BL

E

FIXE

D

CLOSED

v

B

L

F

C

B

v

vv

X

B

A

J

C

I

H

X

v

M

K

v

G

A

The following information should be used for determining the proper location of the vent terminal

for direct vent water heaters.

VVENT TERMINAL XAIR SUPPLY INLET AREA WHERE TERMINAL IS NOT PERMITTED

HORIZONTAL VENT TERMINAL LOCATION FOR POWER DIRECT VENT

Canadian Installations 1US Installations 2

A= Clearance above grade, veranda, porch, deck or

balcony. 12 inches (30 cm) 12 inches (30 cm)

B= Clearance to window or door that may be opened.

• 6 in (15 cm) for appliances < 10,000 Btuh (3

kW),

• 9 in (23 cm) for appliances > 10,000 Btuh (3

kW) and < 50,000 Btuh (15 kW),

• 12 in (30 cm) for appliances > 50,000 Btuh (15

kW)

• 6 in (15 cm) for appliances < 10,000 Btuh (3

kW),

• 9 in (23 cm) for appliances > 10,000 Btuh (3

kW) and < 100,000 Btuh (30 kW),

• 36 in (91 cm) for appliances > 100,000 Btuh

(30 kW)

C= Clearance to permanently closed window. 0 in (0 cm) 0 in (0 cm)

D= Vertical Clearance to ventilated soffit located

above the terminal within a horizontal distance of

2 feet (61 cm) from the center line of the terminal.

12 in (30 cm) 12 in (30 cm)

E= Clearance to unventilated soffit. 12 in (30 cm) 12 in (30 cm)

F= Clearance to outside corner. 24 in (61 cm) 24 in (61 cm)

G= Clearance to inside corner. 18 in (46 cm) 18 in (46 cm)

H = Clearance to each side of center line extended

meter/regulator assembly. above 3 ft (91 cm) within a height of 15 ft (4.6 m) 3 ft (91 cm) within a height of 15 ft (4.6 m)

I = Clearance to service regulator vent outlet. 3 ft (91 cm) 3 ft (91 cm)

J = Clearance to nonmechanical air supply inlet to the

building or the combustion air inlet of any other

appliance..

• 6 in (15 cm) for appliances < 10,000 Btuh (3 kW),

• 9 in (23 cm) for appliances > 10,000 Btuh (3 kW)

and < 100,000 Btuh (30 kW),

• 36 in (91 cm) for appliances > 100,000 Btuh (30

kW)

• 6 in (15 cm) for appliances < 10,000 Btuh (3

kW),

• 9 in (23 cm) for appliances > 10,000 Btuh (3

kW) and < 50,000 Btuh (15 kW),

• 12 in (30 cm) for appliances > 50,000 Btuh

(15 kW)

K = Clearance to mechanical air supply inlet. 6 ft (1.83 m) 3 ft (91 cm) above if within 10 ft (3 m)

horizontally

L = Clearance above paved side walk or paved

driveway located on public property. 7 ft (2.13 m)

7 ft (2.13 m) for mechanical draft system

(Category I appliances); vents for Category II

and IV appliances cannot be located above public

walkways or other areas where condensate or

vapor can cause a nuisance or hazard

M = Clearance under veranda, porch, deck or balcony. 12 in (30 cm) ‡ 12 in (30 cm)*

Direct Vent Terminal Clearances

1 In accordance with the current CSA B149.1, Natural Gas and Propane Installation Code

2 In accordance with the current ANSI Z223.1/ NFPA 54 National Fuel Gas Code.

‡ Permitted only if veranda, porch, deck, or balcony is fully open on a minimum of two sides beneath the oor.

* Permitted only if veranda porch, deck, or balcony is fully open on a minimum of two sides beneath the oor.

Follow local or National gas codes or latest edition of CAN/CSA B149 and Propane installation code.

INSTALLATION

La page charge ...

Rheem GHE50SS-100 Mode d'emploi

Ce manuel convient également à

Rheem GHE50SS-100 Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents