DeWalt D55155 Manuel utilisateur

D55151, D55152, D55153, D55155

Contractor’s Electric 4 Gallon Hand Carry Air Compressor

Compresseurs d’air portatifs électriques de 4 gallons de classe entrepreneur

Compresor de aire portátil elèctrico de 4 galones para contratistas

INSTRUCTION MANUAL

GUIDE D'UTILISATION

MANUAL DE INSTRUCCIONES

INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA

DE GARANTÍA. ADVERTENCIA: LÉASE ESTE INSTRUCTIVO ANTES

DE USAR EL PRODUCTO.

If you have questions or comments, contact us.

Pour toute question ou tout commentaire, nous contacter.

Si tiene dudas o comentarios, contáctenos.

1-800-4-DeWALT • www.dewalt.com

2

English

A. On/Off Switch

B. Air Tank Pressure Gauge

C. Regulated Pressure Gauge

D. Pressure Regulator

E. Quick Connects (if equipped)

F. Check Valve

G. Safety Valve

H. Air Tank Drain Valve

I. Power Cord Wrap

J. Pressure Switch

K. Pump Oil Dipstick

L. Pump Oil Drain Plug

M. Motor Reset

N. Air Intake Filter

Air Compressor

C

NOT A

STEP

D

B

E

K

L

J

D

E

L

M

I

F

B

C

A

G

A

H

K

F

M

N

J

G

FIG. 1

3

English

Speciﬁcations

MODEL

D55151 D55152 D55153 D55155

WEIGHT

56 lbs. (25.4 kg) 65 lbs. (29.5 kg) 58 lbs. (28.3 kg) 61 lbs. (27.7 kg)

HEIGHT

16.75" (425.5 mm)

16.0" (406.4 mm) 16.75" (501.7 mm) 12.5" (317.5 mm)

WIDTH

18.0" (457.2 mm) 18.0" (457.2 mm) 18.0" (457.2 mm) 21.75" (552.5 mm)

LENGTH

15.0 (381 mm) 18.0" (457.2 mm) 15.0 (381 mm) 21.75" (552.5 mm)

AIR TANK CAPACITY (GALLONS)

4.0 (15.1 liters) 4.0 (15.1 liters) 4.0 (15.1 liters) 4.0 (15.1 liters)

APPROX CUT-IN PRESSURE

95 PSI (655 kPa) 95 PSI (655 kPa) 95 PSI (655 kPa) 100 PSI (689.5 kPa)

APPROX. CUT-OUT PRESSURE

125 PSI (861.8 kPa) 125 PSI (861.8 kPa) 125 PSI (861.8 kPa) 125 PSI (861.8 kPa)

SCFM @ 100 PSI (689.5 kPa)

3.2 3.8 3.8

4.5

MOTOR

1.1 HP (continuous) 1.1 HP (continuous) 1.1 HP (continuous) 1.2 HP (continuous)

Volts/Amps/Hertz

120V/12.5 A/60 Hz. 120V/14 A/60 Hz. 120V/14 A/60 Hz. 120V/15 A/60 Hz.

RPM

3450 3450 3450 3450

Minumum Branch Circuit

Requirement

15 Amp 15 Amp 15 Amp 15 Amp

PUMP OIL CAPACITY

6 oz. (177.4 ml) 12 oz. (354.9 ml) 12 oz. (354.9 ml) 4 oz. (118.3 ml)

4

English

Deﬁnitions: Safety Guidelines

The definitions below describe the level of severity

for each signal word. Please read the manual and

pay attention to these symbols.

DANGER: Indicates an imminently hazardous

situation which, if not avoided, will result in death

or serious injury.

WARNING: Indicates a potentially hazardous

situation which, if not avoided, could result in death

or serious injury.

CAUTION: Indicates a potentially hazardous

situation which, if not avoided, may result in minor

or moderate injury.

CAUTION: Used without the safety alert symbol

indicates a potentially hazardous situation which, if

not avoided, may result in property damage.

PUMP

CYLNDER

AND HEAD

Hot Surfaces

FIG. 2

OUTLET TUBE

CHECK

VALVE

CHECK

VALVE

OUTLET TUBE

IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT

THIS OR ANY D

e

WALT TOOL, CALL US TOLL FREE AT:

1-800-4-D

e

WALT (1-800-433-9258)

Important Safety Instructions

WARNING: Do not operate this unit until you read and understand

this instruction manual for safety, operation and maintenance

instructions.

WARNING: Some dust created by power sanding, sawing, grind-

ing, drilling, and other construction activities contains chemicals

known to the State of California to cause cancer, birth defects or other

reproductive harm. Some example of these chemicals are:

• lead from lead-based paints

• crystalline silica from bricks and cement and other masonry

products

• arsenic and chromium from chemically-treated lumber

Your risk from these exposures varies, depending on how often

you do this type of work. To reduce your exposure to these chemi-

cals: work in a well ventilated area, and work with approved safety

equipment, always wear OSHA/MSHA/NIOSH approved, properly

fitting face mask or respirator when using such tools.

When using air tools, basic safety precautions should always be fol-

lowed to reduce the risk of of personal injury.

WARNING: This product contains chemicals, including lead,

known to the State of California to cause cancer, and birth

defects or other reproductive harm. Wash hands after handling.

SAVE THESE INSTRUCTION

5

English

DANGER: RISK OF EXPLOSION OR FIRE

WHAT CAN HAPPEN HOW TO PREVENT IT

• It is normal for electrical

contacts within the motor

and pressure switch to

spark.

•

Always operate the compres-

sor in a well ventilated area

free of combustible materials,

gasoline, or solvent vapors.

•

If electrical sparks from

compressor come into con-

tact with flammable vapors,

they may ignite, causing fire

or explosion.

•

If spraying flammable materi-

als, locate compressor at

least 20 feet (6.1 m) away

from spray area. An addi-

tional length of hose may be

required.

•

Store flammable materials in

a secure location away from

compressor.

• Restricting any of the com-

pressor ventilation openings

will cause serious overheat-

ing and could cause fire.

•

Never place objects against

or on top of compressor.

•

Operate compressor in

an open area at least 12

"

(30.5 cm)

away from any

wall or obstruction that would

restrict the flow of fresh air to

the ventilation openings.

•

Operate compressor in a

clean, dry well ventilated area.

Do not operate unit indoors or

in any confined area.

• Unattended operation of

this product could result in

personal injury or property

damage. To reduce the risk

of fire, do not allow the

compressor to operate unat-

tended.

• Always remain in attendance

with the product when it is

operating.

• Always turn off and unplug

unit when not in use.

DANGER: RISK TO BREATHING (ASPHYXIATION)

WHAT CAN HAPPEN HOW TO PREVENT IT

• The compressed air directly

from your compressor is not

safe for breathing. The air

stream may contain carbon

monoxide, toxic vapors,

or solid particles from the

air tank. Breathing these

contaminant's can cause

serious injury or death.

• Air obtained directly from the

compressor should never

be used to supply air for

human consumption. In order

to use air produced by this

compressor for breathing,

suitable filters and in-line

safety equipment must be

properly installed. In-line

filters and safety equipment

used in conjunction with the

compressor must be capable

of treating air to all applicable

local and federal codes prior to

human consumption.

6

English

• Sprayed materials such as

paint, paint solvents, paint

remover, insecticides, weed

killers, may contain harmful

vapors and poisons.

• Work in an area with good

cross ventilation. Read and

follow the safety instructions

provided on the label or safety

data sheets for the materials

you are spraying. Always use

certified safety equipment:

OSHA/MSHA/NIOSH

respiratory protection designed

for use with your specific

application.

DANGER: RISK OF INJURY OR PROPERTY DAMAGE WHEN

TRANSPORTING OR STORING

WHAT CAN HAPPEN HOW TO PREVENT IT

•

Oil can leak or spill and could

result in fire or breathing

hazard; serious injury or

death can result. Oil leaks will

damage carpet, paint or other

surfaces in vehicles or trailers.

• Always place compressor

on a protective mat when

transporting to protect against

damage to vehicle from leaks.

Remove compressor from

vehicle immediately upon arrival

at your destination. Always keep

compressor level and never lie

on its side.

WARNING: RISK OF BURSTING

Air Tank:

The air tank on your Air Compressor is designed and may

be UM coded (for units with air tanks greater than 6 inch diameter)

according to ASME Section VIII, Div. 1 rules. All pressure vessels

should be inspected once every two years. To find your state pressure

vessels inspector, look under the Division of Labor and Industries in

the government section of a phone book or call 1-800-4-DeWALT for

assistance.

The following conditions could lead to a weakening of the air tank,

and result in a violent air tank explosion:

WHAT CAN HAPPEN HOW TO PREVENT IT

• Failure to properly drain

condensed water from

air tank, causing rust and

thinning of the steel air tank.

• Drain air tank daily or after

each use. If air tank develops

a leak, replace it immediately

with a new air tank or replace

the entire compressor.

• Modifications or attempted

repairs to the air tank.

• Never drill into, weld, or make

any modifications to the air

tank or its attachments. Never

attempt to repair a damaged or

leaking air tank. Replace with a

new air tank.

• Unauthorized modifications

to the safety valve or any

other components which

control air tank pressure.

• The air tank is designed

to withstand specific

operating pressures. Never

make adjustments or parts

substitutions to alter the factory

set operating pressures.

7

English

Attachments & accessories:

• Exceeding the pressure

rating of air tools, spray guns,

air operated accessories,

tires, and other inflatables

can cause them to explode

or fly apart, and could result

in serious injury.

• Follow the equipment

manufacturers

recommendation and never

exceed the maximum

allowable pressure rating

of attachments. Never use

compressor to inflate small

low pressure objects such

as children’s toys, footballs,

basketballs, etc.

WARNING: RISK OF ELECTRICAL SHOCK

WHAT CAN HAPPEN HOW TO PREVENT IT

• Your air compressor is

powered by electricity.

Like any other electrically

powered device, If it is not

used properly it may cause

electric shock.

•

Never operate the

compressor outdoors when it

is raining or in wet conditions.

•

Never operate compressor

with protective covers

removed or damaged.

• Repairs attempted by

unqualified personnel can

result in serious injury or

death by electrocution.

•

Any electrical wiring or

repairs required on this

product should be performed

by a DeWALT factory

service center or a DeWALT

authorized service center in

accordance with national and

local electrical codes.

• Electrical Grounding:

Failure to provide adequate

grounding to this product

could result in serious injury

or death from electrocution.

See Grounding

Instructions under

Installation.

•

Make certain that the

electrical circuit to which the

compressor is connected

provides proper electrical

grounding, correct voltage

and adequate fuse protection.

WARNING: RISK FROM FLYING OBJECTS

WHAT CAN HAPPEN HOW TO PREVENT IT

• The compressed air stream

can cause soft tissue

damage to exposed skin and

can propel dirt, chips, loose

particles, and small objects

at high speed, resulting in

property damage or personal

injury.

•

Always wear certified safety

equipment: ANSI Z87.1 eye

protection (CAN/CSA Z94.3)

with side shields when using

the compressor.

• Never point any nozzle or

sprayer toward any part of

the body or at other people or

animals.

• Always turn the compressor off

and bleed pressure from the

air hose and air tank before

attempting maintenance,

attaching tools or accessories.

8

English

WARNING: RISK OF HOT SURFACES

WHAT CAN HAPPEN HOW TO PREVENT IT

• Touching exposed metal

such as the compressor

head, engine head, engine

exhaust or outlet tubes, can

result in serious burns.

• Never touch any exposed

metal parts on compressor

during or immediately after

operation. Compressor will

remain hot for several minutes

after operation.

• Do not reach around

protective shrouds or attempt

maintenance until unit has

been allowed to cool.

WARNING: RISK FROM MOVING PARTS

WHAT CAN HAPPEN HOW TO PREVENT IT

• Moving parts such as the

pulley, flywheel, and belt can

cause serious injury if they

come into contact with you or

your clothing.

• Never operate the compressor

with guards or covers which

are damaged or removed.

•

Keep your hair, clothing, and

gloves away from moving

parts. Loose clothes, jewelry,

or long hair can be caught in

moving parts.

• Air vents may cover moving

parts and should be avoided

as well.

• Attempting to operate

compressor with damaged or

missing parts or attempting

to repair compressor with

protective shrouds removed

can expose you to moving

parts and can result in

serious injury.

• Any repairs required on this

product should be performed

by a DeWALT factory

service center or a DeWALT

authorized service center.

WARNING: RISK OF UNSAFE OPERATION

WHAT CAN HAPPEN HOW TO PREVENT IT

• Unsafe operation of your air

compressor could lead to seri-

ous injury or death to you or

others.

•

Review and understand all

instructions and warnings in

this manual.

• Become familiar with the

operation and controls of the

air compressor.

•

Keep operating area clear of all

persons, pets, and obstacles.

• Keep children away from the

air compressor at all times.

•

Do not operate the product

when fatigued or under the

influence of alcohol or drugs.

Stay alert at all times.

• Never defeat the safety fea-

tures of this product.

9

English

• Equip area of operation with a

fire extinguisher.

• Do not operate machine with

missing, broken, or unautho-

rized parts.

WARNING: RISK OF FALLING

WHAT CAN HAPPEN HOW TO PREVENT IT

• A portable compressor

can fall from a table,

workbench, or roof causing

damage to the compressor

and could result in serious

injury or death to the

operator.

• Always operate compressor

in a stable secure position to

prevent accidental movement

of the unit. Never operate

compressor on a roof or

other elevated position. Use

additional air hose to reach

high locations.

CAUTION: RISK FROM NOISE

WHAT CAN HAPPEN HOW TO PREVENT IT

• Under some conditions and

duration of use, noise from

this product may contribute

to hearing loss.

• Always wear certified safety

equipment: ANSI S12.6

(S3.19) hearing protection.

SAVE THESE INSTRUCTIONS

FOR FUTURE USE

FEATURES (

Fig. 1)

ON/OFF SWITCH

Place this switch (A) in the ON position to

G

A

J

provide automatic power to the pressure

switch and OFF to remove power at the

end of each use.

PRESSURE SWITCH

The pressure switch (J) automatically

starts the motor when the air tank pres-

sure drops below the factory set cut-in

pressure. It stops the motor when the air tank pressure reaches the

factory set cut-out pressure.

PRESSURE RELEASE VALVE

The pressure release valve located on the side of the pressure switch,

is designed to automatically release compressed air from the compres-

sor head and the outlet tube when the air compressor reaches cut-out

pressure or is shut off. The pressure release valve allows the motor to

restart freely. When the motor stops running, air will be heard escaping

from this valve for a few seconds. No air should be heard leaking when

the motor is running or after the unit reaches cut-out pressure.

SAFETY VALVE

If the pressure switch does not shut off the air compressor at its

cut-out pressure setting, the safety valve (G) will protect against

high pressure by popping out at its factory set pressure (slightly

higher than the pressure switch cut-out setting).

CHECK VALVE

When the air compressor is operating, the check

F

valve (F) is open, allowing compressed air to enter

the air tank. When the air compressor reaches cut-

out pressure, the check valve closes, allowing air

pressure to remain inside the air tank.

10

English

TANK PRESSURE GAUGE

The tank pressure gauge (B) indi-

D

C

E

B

cates the reserve air pressure in

the tank.

OUTLET PRESSURE GAUGE

The outlet pressure gauge (C)

indicates the air pressure available

at the outlet side of the regulator.

This pressure is controlled by the regulator and is always less than

or equal to the tank pressure.

REGULATOR

The regulator (D) controls the air pressure shown on the outlet

pressure gauge. Turn regulator knob clockwise to increase pres-

sure and counterclockwise to decrease pressure.

UNIVERSAL QUICK CONNECT BODIES (IF EQUIPPED)

The universal quick connect body (E) accepts the three most

popular styles of quick connect plugs: Industrial, automotive, and

ARO. One hand push-to-connect operation makes connections

simple and easy. The two quick connect bodies allow the use of two

tools at the same time.

DRAIN VALVE

The drain valve (H) is located at the base

H

of the air tank and is used to drain conden-

sation at the end of each use.

See Draining

Air Tank

under Maintenance.

COOLING SYSTEM

This compressor contains an advanced design cooling system.

It is normal for this fan to blow air through the vent holes in large

amounts. The cooling system is working when air is expelled.

AIR COMPRESSOR PUMP

The pump compresses air into the air tank. Working air is not

available until the compressor has raised the air tank pressure

above that required at the air outlet.

MOTOR OVERLOAD PROTECTOR

This motor has a manual thermal overload

K

M

N

protector. If the motor overheats for any

reason, the overload protector will shut off

the motor. The motor must be allowed to

cool down before restarting. To restart:

1. Ensure the On/Off switch (A) is in the

OFF position.

2. Allow the motor to cool.

3. Depress the reset button (M) on the

motor.

OIL DIPSTICK

The oil dipstick (K) indicates the amount of oil in the pump. Check

pump oil daily, see Compressor Pump Oil under Maintenance.

AIR INTAKE FILTER

The filter (N) is designed to clean air entering the pump. To ensure

the pump continually receives a clean, cool, and dry air supply the

filter must always be clean and the filter intake must be free from

obstructions.

INSTALLATION

Assembly

INSTALLING HOSES

WARNING: Risk of unsafe operation. Firmly grasp hose in hand

when installing or disconnecting to prevent hose whip.

1. Ensure regulated pressure gauge reads 0 PSI (0 kPa).

11

English

2. Grasp the hose at the quick connect plug and push the plug

into the quick connect body (E). Coupler will snap into place.

3. Grasp the hose and pull to ensure coupler is seated.

DISCONNECTING HOSES

WARNING: Risk of unsafe operation. Firmly grasp hose in hand

when installing or disconnecting to prevent hose whip.

1. Ensure regulated pressure gauge reads 0 PSI (0 kPa).

2. Pull coupler on quick connect body back to release quick

connect plug on hose.

Lubrication and Oil

CAUTION: The compressor was shipped without oil in the

crankcase. A small amount of oil may be present in the pump

upon receipt of the air compressor. This is due to testing and does

not mean the pump contains oil. Do not attempt to operate this

air compressor without first adding oil to the crankcase. Serious

damage can result from even limited operation unless filled with

oil and broken in correctly. Closely follow Initial Set-up under

Operation.

CAUTION: Multi-viscosity motor oils, like 10W-30, should not be

used in an air compressor. They leave carbon deposits on critical

components, thus reducing performance and compressor life. Use

DeWALT synthetic oil only.

1. Place unit on a level surface.

K

2. Remove dipstick (K) and slowly add

DeWALT synthetic oil (supplied). NOTE: See

Specifications for pump oil capacity.

CAUTION: Risk of unsafe operation. Overfilling

with oil will cause premature compressor failure.

Do not overfill.

3. Replace dipstick.

Grounding Instructions

WARNING: Risk of electrical shock. In the event of a short

circuit, grounding reduces the risk of shock by providing an escape

wire for the electric current. This air compressor must be properly

grounded.

The portable air compressor is equipped with a cord having a

grounding wire with an appropriate grounding plug.

1. The cord set and plug (O) with this unit

P

O

Q

contains a grounding pin (P). This plug

MUST be used with a grounded outlet

(Q).

IMPORTANT:

The outlet being used must

be installed and grounded in accordance

with all local codes and ordinances.

2. Ensure the outlet being used has the same configuration as the

grounded plug. DO NOT USE AN ADAPTER.

3. Inspect the plug and cord before each use. Do not use if there

are signs of damage.

4. If these grounding instructions are not completely understood, or

if in doubt as to whether the compressor is properly grounded,

have the installation checked by a qualified electrician.

DANGER: Risk of electrical shock. IMPROPER GROUNDING

CAN RESULT IN ELECTRICAL SHOCK.

• Do not modify the plug provided. If it does not fit the available

outlet, a correct outlet should be installed by a qualified electri-

cian.

• Repairs to the cord set or plug MUST be made by a qualified

electrician.

12

English

Extension Cords

Using extension cords is not recommended. The use of extension

cords will cause voltage to drop resulting in power loss to the motor

and overheating.

Instead of using an extension cord, increase the working reach of

the air hose by attaching another length of hose to its end. Attach

additional lengths of hose as needed.

If an extension cord must be used, be sure it is:

• a 3-wire extension cord that has a 3-blade grounding plug, and

a 3-slot receptacle that will accept the plug on the product

• in good condition

• no longer than 50 feet (15,2 m)

• 12 gauge (AWG) or larger. (Wire size increases as gauge num

-

ber decreases. 10 AWG and 8 AWG may also be used. DO NOT

USE 14 OR 16 AWG.)

Voltage and Circuit Protection

Refer to the Voltage and Minimum Branch Circuit Requirements

under Specifications.

CAUTION: Certain air compressors can be operated on a

15 amp circuit if the following conditions are met.

• Voltage supply to circuit must comply with the National Electrical

Code.

• Circuit is not used to supply any other electrical needs.

• Extension cords comply with specifications.

• Circuit is equipped with a 15 amp circuit breaker or 15 amp

time delay fuse. NOTE: If compressor is connected to a circuit

protected by fuses, use only time delay fuses. Time delay fuses

should be marked “D” in Canada and “T” in the US.

If any of the above conditions cannot be met, or if operation of the

compressor repeatedly causes interruption of the power, it may be

necessary to operate it from a 20 amp circuit. It is not necessary to

change the cord set.

Compatibility

Air tools and accessories that are run off the compressor must be

compatible with petroleum-based products. If you suspect that a

material is not compatible with petroleum products, an air line filter

for removal of moisture and oil vapor in compressed air is required.

NOTE:

Always use an air line filter to remove moisture and oil vapor

when spraying paint.

Location

Place the air compressor in a clean, dry and well ventilated area

at least 12"

(30.5 cm) away from the wall or other obstructions that

will interfere with the flow of air. Keep the compressor away from

areas that have dirt and/or volatile fumes in the atmosphere. These

impurities may clog the intake filter and valves, causing inefficient

operation.

The air compressor pump and shroud are designed to allow for

proper cooling. The ventilation openings on the compressor are

necessary to maintain proper operating temperature. Do not place

rags or other containers on or near these openings.

Place the air compressor on a flat surface resting on the rubber

feet.

NOISE CONSIDERATIONS

Consult local officials for information regarding acceptable noise

levels in your area. To reduce excessive noise, use vibration mounts

or silencers, relocate the unit or construct total enclosures or baffle

walls. Contact a D

e

WALT service center or call 1-800-4-D

e

WALT for

assistance.

13

English

ELECTRICAL

Refer to all safety instructions before using unit. Observe extension

cord safety instructions if necessary. Always move the On/Off

switch (A) to the OFF

position before removing the plug from the

outlet.

TRANSPORTING

When transporting the compressor in a vehicle, trailer, etc., ensure

that the tank is drained and the unit is secured. Use care when driv-

ing to avoid tipping the unit over in the vehicle. Damage can occur to

the compressor or surrounding items if the compressor is tipped.

MOVING

When moving the compressor, grasp the handle and carry the com-

pressor as close to the body as possible.

WARNING: Risk of unsafe operation. Ensure proper footing and

use caution when carrying compressor to avoid a loss of balance.

PREPARATION FOR USE

Pre-Start Checklist (Fig. 1)

1.

Ensure the On/Off switch (A) is in the OFF position.

2.

Plug the power cord into the correct branch circuit receptacle.

See Voltage and Circuit Protection under Installation.

3. Ensure air tank is drained, see Draining Air Tank under

Maintenance.

4. Ensure the drain valve (H) is closed.

5. Ensure safety valve (G) is functioning properly, see

Checking

Safety Valve

under Maintenance.

6. Check pump oil level, see Compressor Pump Oil

under

Maintenance.

CAUTION:

Do not operate without oil or with inadequate oil. DeWALT

is not responsible for compressor failure caused by inadequate oil.

7. Turn regulator knob (D) counterclockwise until fully closed. Ensure

regulated pressure gauge reads 0 PSI (0 kPa).

8. Attach hose and accessories.

WARNING: Risk of unsafe operation. Firmly grasp hose in hand

when installing or disconnecting to prevent hose whip.

9. Ensure all covers and labels are in place, legible (for labels) and

securely mounted. Do not use compressor until all items have

been verified.

WARNING: Risk of bursting. Too much air pressure causes a

hazardous risk of bursting. Check the manufacturer’s maximum

pressure rating for air tools and accessories. The regulator outlet

pressure must never exceed the maximum pressure rating.

Initial Set-up

(Fig. 1)

WARNING: Do not operate this unit until you read and understand

this instruction manual for safety, operation and maintenance

instructions.

BREAK-IN PROCEDURE

WARNING:

Serious damage may result if the following break-in

instructions are not closely followed.

This procedure is required before the air compressor is put into

service for the first time and when the check valve or a compressor

pump/motor has been replaced.

1. Ensure the On/Off switch (A) is in the OFF position.

NOTE:

If hose is not connected to Quick Connect body, pull coupler

back until it clicks to prevent air from escaping through the quick

connect.

2.

Plug the power cord into the correct branch circuit receptacle.

See

Voltage and Circuit Protection

under Installation.

14

English

3. Open the drain valve (counter-clockwise) fully to permit air to

escape and prevent air pressure build up in the air tank during

the break-in period.

4. Move the On/Off switch to the ON position. The compressor will

start.

5. Run the compressor for 20 minutes.

6. After 20 minutes, close the drain valve by turning clockwise.

The tank will fill to cut-out pressure and the motor will stop.

7. Compressed air will be available until it is used or bled off.

OPERATING PROCEDURES

Start-up (Fig. 1)

1. Follow Pre-Start Checklist under Preparation for Use.

2. Move the On/Off switch to the ON position and allow tank pres-

sure to build. Motor will stop when tank pressure reaches

cut-out pressure.

CAUTION: Risk of unsafe operation. Compressed air from the unit

may contain water condensation and oil mist. Do not spray unfil-

tered air at an item that could be damaged by moisture. Some air

operated tools or devices may require filtered air. Read the instruc-

tions for the air tool or device.

3. Adjust regulator (D) to desired setting. See Regulator

under

Features.

Shut-down (Fig. 1)

1 Move On/Off switch (A) is in the OFF position. NOTE: If finished

using compressor, follow Steps 2 - 6.

2. Turn regulator knob (D) counterclockwise until fully closed. Ensure

regulated pressure gauge reads 0 PSI (0 kPa).

3. Remove hose and accessory.

4. Drain the air tank,

see Draining Air Tank under Maintenance

.

Ensure air tank pressure gauge reads 0 PSI (0 kPa).

WARNING: Risk of bursting. Drain air tank daily. Water will con-

dense in air tank. If not drained, water will corrode and weaken the

air tank causing a risk of air tank rupture.

5. Allow the compressor to cool down.

6. Wipe air compressor clean and store in a safe, non-freezing

area.

MAINTENANCE

The following procedures must be followed when maintenance or

service is performed on the air compressor.

1. Ensure On/Off switch is in the OFF position.

2. Remove air compressor plug from outlet.

3. Drain air tank.

4. Allow air compressor to cool down before starting service.

NOTE:

All compressed air systems contain maintenance parts (e.g.,

oil, filters, separators) that are periodically replaced. These used parts

may contain substances that are regulated and must be disposed of in

accordance with local, state, and federal laws and regulations.

NOTE:

Take note of the positions and locations of parts during

disassembly to make reassembly easier.

NOTE:

Any service operations not included in this section should

be performed by a D

e

WALT factory service center or a D

e

WALT

authorized service center.

15

English

Maintenance Chart

Procedure Daily Weekly Monthly 1 year or

200 Hours

Check safety valve

X

Inspect air filter

+

X

Drain air tank

X

Check pump oil level

X

Change pump oil**

+

X

Oil leak inspection

X

Check for unusual noise/

vibration

X

Check for air leaks*

X

Clean compressor exterior

X

* To check for air leaks apply a solution of soapy water around joints.

While compressor is pumping to pressure and after pressure cuts out,

look for air bubbles to form.

** The pump oil must be changed after the first 20 hours of operation.

Thereafter, when using

DeWALT

synthetic compressor oil, change oil

every 200 hours of operation or once a year, whichever comes first.

+ Perform more frequent in dusty or humid conditions

Checking Safety Valve (Fig. 1)

WARNING: Hot surfaces. Risk of burn. Aftercooler, pump head,

and surrounding parts are very hot, do not touch (see the Hot

Surfaces identified in Fig. 2). Allow compressor to cool prior to

servicing.

WARNING: Risk of bursting. If the safety valve does not work

properly, over-pressurization may occur, causing air tank rupture or

an explosion.

Before starting compressor, pull the ring on the safety valve to

make sure that the safety valve operates freely. If the valve is stuck

or does not operate smoothly, it must be replaced with the same

type of valve.

Checking Air Filter Element (Fig. 1)

WARNING: Hot surfaces. Risk of burn. Aftercooler, pump head, and

surrounding parts are very hot, do not touch (see the Hot Surfaces

identified in Fig. 2). Allow compressor to cool prior to servicing.

1. Ensure the On/Off switch (A) is in the OFF position.

2. Allow unit to cool.

3. Remove air filter (N) from unit.

4. Carefully pry filter top from base.

5. Remove element from filter base.

6. If element needs cleaning, blow out with air. Replace if needed.

Purchase replacement parts from your local dealer or authorized

service center. Always use identical replacement parts.

7. Place element back in filter base.

8. Snap filter top to filter base.

9. Reassemble air filter to unit. Ensure exhaust outlet points down.

CAUTION: Risk of unsafe operation. Do not operate without air

inlet filter

Draining Air Tank (Fig. 1)

WARNING: Risk of unsafe operation. Risk from noise. Air tanks

contain high pressure air. Keep face and other body parts away from

outlet of drain. Use safety glasses [ANSI Z87.1 (CAN/CSA Z94.3)]

when draining as debris can be kicked up into face. Use ear protection

[ANSI S12.6 (S3.19)] as air flow noise is loud when draining.

16

English

NOTE: All compressed air systems generate condensate that

accumulates in any drain point (e.g. tanks, filter, aftercoolers, dryers).

This condensate contains lubricating oil and/or substances which

may be regulated and must be disposed of in accordance with local,

state, and federal laws and regulations.

1. Ensure On/Off switch is in the OFF position

.

2. Move compressor into an inclined position so drain valve (H) is

at the lowest point (this will assist in removing moisture, dirt, etc.

from air tanks)

3. Place a suitable container under the drain valve to catch

discharge.

4. Grasp knurled knob on drain valve.

5. Slowly rotate knob to gradually bleed air from air tank.

WARNING: Risk of bursting. Drain air tank daily. Water will con-

dense in air tank. If not drained, water will corrode and weaken the

air tank causing a risk of air tank rupture.

CAUTION: Risk of property damage. Drain water from air tank may

contain oil and rust, which can cause stains.

6. When air tank pressure gauge reads 10 PSI (68,9 kPa), rotate

valve to the fully open position.

7. Close drain valve when finished.

Compressor Pump Oil (Fig. 1)

CHECKING OIL

WARNING: Hot surfaces. Risk of burn. Aftercooler, pump head,

and surrounding parts are very hot, do not touch (see the Hot

Surfaces identified in Fig. 2). Allow compressor to cool prior to

servicing.

1. Ensure On/Off switch is in the OFF position

.

2. Place unit on a flat level surface.

3. Remove dipstick (K) and wipe clean.

4. Reinsert dipstick fully into oil fill port for a few

L

K

seconds to allow oil to collect on the dipstick.

5. Remove oil dipstick to read oil level. Oil should

not exceed top raised line on dipstick. If oil is

below lower mark, add DeWALT synthetic oil

and follow Steps 4 - 6.

NOTE: When filling the crankcase, the oil

flows very slowly into the pump. If the oil is

added too quickly, it will overflow and appear

to be full.

CAUTION: Risk of unsafe operation. Overfilling with

oil will cause premature compressor failure. Do not

overfill.

6. Replace dipstick.

CHANGING OIL

NOTE:

Pump oil contains substances that are regulated

and must be disposed of in accordance with local,

state and federal laws and regulations.

WARNING: Hot surfaces. Risk of burn. Aftercooler,

pump head, and surrounding parts are very hot, do not touch (see

the Hot Surfaces identified in Fig. 2). Allow compressor to cool prior

to servicing.

1. Ensure On/Off switch is in the OFF position

.

2. Allow the unit to cool.

3. Remove air compressor plug from outlet.

4. Drain air tank.

5. Locate a suitable container under pump drain plug (L).

6. Remove the dipstick (K) from crankcase.

MAX

MIN

17

English

7. Remove the oil drain plug (L).

8. Allow ample time for all oil to drain out. (Tilting the compressor

towards the drain plug will assist in draining.)

9. Install the oil drain plug.

10. Fill pump with D

eWALT synthetic compressor oil.

11. Replace dipstick.

ACCESSORIES

Recommended accessories for use with your tool are available

for purchase from your local dealer or authorized service center.

If you need assistance in locating any accessory for your tool,

please contact D

e

WALT Industrial Tool Co., 701 East Joppa Road,

Baltimore, MD 21286, call 1-800-4-D

e

WALT (1-800-433-9258) or visit

our website www.dewalt.com.

CAUTION: The use of any other accessory not recommended for

use with this tool could be hazardous. Use only accessories rated

equal to or higher than the rating of the air compressor.

SERVICE INFORMATION

Please have the following information available for all service calls:

Model Number ____________ Serial Number _________________

Date and Place of Purchase ______________________________

Repairs

To assure product SAFETY and RELIABILITY, repairs, maintenance

and adjustment should be performed by a D

e

WALT factory service

center, a D

e

WALT authorized service center or other qualified

service personnel. Always use identical replacement parts.

Full One Year Warranty

DeWALT heavy duty industrial tools are warranted for one year from

date of purchase. We will repair, without charge, any defects due

to faulty materials or workmanship. For warranty repair information,

call 1-800-4-D

e

WALT. This warranty does not apply to accessories

or damage caused where repairs have been made or attempted by

others. This warranty gives you specific legal rights and you may

have other rights which vary in certain states or provinces.

LATIN AMERICA:

This warranty does not apply to products sold

in Latin America. For products sold in Latin America, see country

specific warranty information contained either in the packaging, call

the local company or see website for warranty information.

FREE WARNING LABEL REPLACEMENT:

If your warning labels

become illegible or are missing, call 1-800-4-D

e

WALT for a free

replacement.

18

English

GLOSSARY

CFM: Cubic feet per minute.

SCFM:

Standard cubic feet per minute; a unit of measure of air delivery.

PSI:

Pounds per square inch; a unit of measure of pressure.

kPa (kilopascal):

Metric pressure measurement. 1 kilopascal equal 1000 pascals.

Code Certification: Products that bear one or more of the following marks: UL, CUL, ETL, CETL, have been evaluated by OSHA certified

independent safety laboratories and meet the applicable Underwriters Laboratories Standards for Safety.

Cut-In Pressure:

While the motor is off, air tank pressure drops when accessory is used. When the tank pressure drops to a certain low

level the motor will restart automatically. The low pressure at which the motor automatically restarts is called cut-in pressure.

Cut-Out Pressure:

When an air compressor is turned on and begins to run, air pressure in the air tank begins to build. It builds to a

certain high pressure before the motor automatically shuts off, protecting your air tank from pressure higher than its capacity. The

high pressure at which the motor shuts off is called cut-out pressure.

Branch Circuit: The circuit carrying electricity from electrical panel to outlet.

Duty Cycle: This air compressor pump is capable of running continuously. However, to prolong the life of your air compressor, it is

recommended that a 50%-75% average duty cycle be maintained; that is, the air compressor pump should not run more than 30-

45 minutes in any given hour.

19

English

Troubleshooting Guide

This section provides a list of the more frequently encountered malfunctions, their causes and corrective actions. The operator or maintenance

personnel can perform some corrective actions, and others may require the assistance of a qualified DeWALT technician or your dealer.

Problem Code

Excessive air tank pressure-safety valve pops off ......................................................................1,2

Air leaks ....................................................................................................................................3

Air leaks in air tank or at air tank welds ....................................................................................4

Air leaks between head and valve plate ....................................................................................5

Air leaks from safety valve .........................................................................................................6

Knocking Noise ..........................................................................................................................6,16,17

Pressure reading on the regulated pressure gauge drops when an accessory is used ...........7

Compressor is not supplying enough air to operate accessories..............................................8,9,10,11,12,15

Regulator knob has continuous air leak ....................................................................................13

Regulator will not shut off air outlet ...........................................................................................13

Moisture in pump crankcase ......................................................................................................14,18

Motor will not run .......................................................................................................................11,19,20,21,22,23,24,25,26

Troubleshooting Codes

CODE POSSIBLE CAUSE POSSIBLE SOLUTION

1 Pressure switch does not shut off motor when compressor

reaches cut-out pressure

Set the On/Off switch to OFF, if the unit does not shut

off

contact a D

e

WALT factory service center or a D

e

WALT

authorized service center.

2

Pressure switch cut-out too high

Contact a D

e

WALT factory service center or a D

e

WALT

authorized service center.

20

English

CODE POSSIBLE CAUSE POSSIBLE SOLUTION

3

Tube fittings are not tight enough Tighten fittings where air can be heard escaping. Check

fittings with soapy water solution.

Do Not Overtighten.

4 Defective air tank Air tank must be replaced. Do not repair the leak.

WARNING: Risk of bursting. Do not drill into, weld or

otherwise modify air tank or it will weaken. The air tank can

rupture or explode.

5 Leaking seals Contact a D

e

WALT factory service center or a D

e

WALT

authorized service center.

6 Defective safety valve Operate safety valve manually by pulling on ring. If valve

still leaks, it must be replaced.

7

Regulator is not adjusted correctly for accessory being

used

It is normal for some pressure drop to occur when an acces-

sory is used, adjust the regulator as instructed in Regulator

under Features if pressure drop is excessive.

NOTE:

Adjust the regulated pressure under flow conditions

while accessory is being used.

8 Prolonged excessive use of air Decrease amount of air usage.

9 Compressor is not large enough for accessory Check the accessory air requirement. If it is higher than

the SCFM or pressure supplied by your air compressor, a

larger compressor is needed to operate accessory.

10 Hole in air hose Replace air hose.

11 Check valve restricted Remove, clean or replace.

12

Air leaks Tighten fittings.

La page charge ...

DeWalt D55155 Manuel utilisateur

Ce manuel convient également à

DeWalt D55155 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents