Linak DL8IC Manuel utilisateur

Marque: Linak

Modèle: DL8IC

Taper: Manuel utilisateur

Ce manuel convient également à

LINAK.COM

/DESKLINE

DL8IC, DL9IC, DL10IC and DL11IC system

User manual

Contents

Preface ........................................................................................................................................ 3

Important information .................................................................................................................. 4

Safety instructions ......................................................................................................................... 4

Safety issues .................................................................................................................................. 6

Before installation, reinstallation or troubleshooting.................................................................... 7

Before start-up .............................................................................................................................. 7

During operation ........................................................................................................................... 7

Misc ........................................................................................................................................... 7

Only for EU markets ....................................................................................................................... 7

Only for Non EU markets ............................................................................................................... 8

Misuse .......................................................................................................................................... 8

Informations importantes ............................................................................................................. 9

Consignes de sécurité .................................................................................................................... 9

Seulement pour les marchés au sein de l´UE .............................................................................. 10

Seulement pour les marchés hors UE .......................................................................................... 10

Utilisation abusive ......................................................................................................................... 10

Repairs .......................................................................................................................................... 10

Declaration of incorporation of partly completed machinery ..................................................... 11

Misc. on the DESKLINE

DL8IC/DL9IC/DL10IC/DL11IC system ...................................................... 12

Warranty ....................................................................................................................................... 12

Maintenance ................................................................................................................................. 12

ETL-marking ................................................................................................................................... 12

Description of the DESKLINE

system ........................................................................................... 13

Mounting guidelines for the DL8IC/DL9IC/DL10IC/DL11IC (motor housing) ................................ 14

Mounting guidelines for the DL8IC/DL9IC (foot part) ................................................................... 14

Mounting guidelines for the DL10IC (foot part)............................................................................. 14

Mounting guidelines for the DL11IC (foot part)............................................................................. 15

PIEZO

: description of the feature ............................................................................................. 19

Desk Control Apps ……………………………………….…………………………………………………………………………… 20

Accessories and repair .................................................................................................................. 20

Disposal of LINAK products .......................................................................................................... 21

Labels ......................................................................................................................................... 22

Drawing appendix ......................................................................................................................... 20

Declaration of conformity ............................................................................................................. 29

LINAK application policy .............................................................................................................. 30

Addresses ...................................................................................................................................... 31

Preface

Dear User,

We are delighted that you have chosen a product from LINAK

LINAK systems are high-tech products based on many years of experience in the manufacture and

development of actuators, electric control boxes, controls and chargers.

This User Manual does not address the end-user. It is intended as a source of information for the

manufacturer of the equipment or system only, and it will tell you how to install, use and maintain

your LINAK electronics. It is the responsibility of the manufacturer of the end-use product to provide a

User Manual where relevant safety information from this manual is passed on to the end-user.

We are sure that your LINAK product/system will give you many years of problem-free operation.

Before our products leave the factory they undergo full function and quality testing. Should you

nevertheless experience problems with your LINAK product/system, you are always welcome to

contact your local dealer.

LINAK subsidiaries and some distributors situated all over the world have authorised service centres,

which are always ready to help you.

LINAK provides a warranty on all its products. This warranty, however, is subject to correct use in

accordance with the specifications, maintenance being done correctly and any repairs being carried

out at a service centre, which is authorised to repair LINAK products.

Changes in installation and use of LINAK products/systems can affect their operation and durability.

The products are not to be opened by unauthorised personnel.

The User Manual has been written based on our present technical knowledge. We are constantly

working on updating the information and we therefore reserve the right to carry out technical

modifications.

LINAK A/S

Important information

Important information on LINAK

products can be found under the following

headings:

Warning!

Failure to comply with these instructions may result in accidents

involving serious personal injury.

General

Safe use of the system is possible only when the operating instructions are

read completely and the instructions contained are strictly observed.

Failure to comply with instructions marked with the ”NOTE” symbol may

result in serious damage to the system or one of its components.

It is important for everyone who is to connect, install, or use the

systems to have the necessary information and access to this User

Manual. Follow the instructions for mounting – risk of injury if these

instructions are not followed.

The appliance is not intended for use by young children or infirm

persons without supervision.

If there is visible damage on the product it must not be installed.

Note that during construction of applications, in which the actuator

is to be fitted, there must be no possibility of personal injury, for

example the squeezing of fingers or arms.

Only the power supply type SMPS001, SMPS002 or SMPS006, shall be

used with the system.

The power supply shall not be covered while operating to allow sufficient

cooling of this appliance.

...to be continued

Failing to follow these instructions can result in the product being damaged

or being destroyed.

Safety instruction

Furthermore take care about the connecting wires from the power

supply to the DL8IC/DL9IC/DL10IC/DL11IC system, don’t damage this by

overrun.

Assure free space for movement of application in both directions to

avoid blockade.

The appliance is only to be used with the power supply unit provided

with the appliance.

This device complies with part 15 of the

FCC Rules. Operation is subject to the

following two conditions:

(1) This device may not cause harmful

interference, and

(2) This device must accept any

interference received, including

interference that may cause

undesired operation

• Statement – for all intentional and unintentional radiators:

Changes or modifications not expressly approved by the party

responsible for compliance could void the user’s authority to operate the

equipment.

• Statement for digital devices for Class B:

NOTE: This equipment has been tested and found to comply with the limits for a

Class B diwgital device, pursuant to part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference in a

residential installation. This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance with the instructions

it may cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television reception, which

can be determined by turning the equipment off and on, the user is encouraged to

try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and the receiver.

- Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

- Consult the dealer or an experienced radio/ TV technician for help.

Safety issues

The builder of the equipment shall ensure that the use of the

component complies with relevant standards – like the Machine

Directive. Care must be taken to avoid squeezing of cables as it can cause

movement of the system! The SMPS001/SMPS002/SMPS006 must not be

packed in heat insulating material, but must be placed so that it can emit

waste heat to the surroundings. There are no ventilation holes to

consider, the SMPS emits heat through its surface.

Only the power supply type SMPS001, SMPS002 or SMPS006, shall be

used with the system.

Before installation, re-installation, or troubleshooting:

• Stop the DL.

• Switch off the power supply and pull out the mains plug.

• Relieve the DL of any loads, which may be released during the work.

Before start-up:

• Make sure that the system has been installed as instructed in this User

Manual.

• Make sure that the voltage of the control box is correct before the system

is connected to the mains.

• System connection. The individual parts must be connected before the

control box is connected to the mains. See the User Manual for LINAK

actuators, if necessary.

During operation

• If the column makes unusual noise or smells, switch off the mains voltage

immediately.

• Take care that the cables are not damaged.

• Unplug the mains cable on mobile equipment before it is moved.

• The products must only be used in an environment, that corresponds to

their IP protection.

Misc.

The actuator system has a sound level below 55dB(A) in typical applications.

Updated manuals and declarations can always be found here:

www.linak.com/deskline

Only for EU markets

This appliance can be used by children aged from 8 years and above

and persons with reduced physical, sensory or mental capabilities or

lack of experience and knowledge if they have given supervision or

instruction concerning use of the appliance in a safe way and understand the

hazards involved.

Children shall not play with the appliance. Cleaning and user

maintenance shall not be made by children without supervision.

Only for Non EU markets

Persons who do not have the necessary experience or knowledge of

the product/products must not use the product/products. Besides,

persons with reduced physical, sensory or mental abilities must not use the

product/ products, unless they are under surveillance or they have been

thoroughly instructed in the use of the apparatus by a person who is

responsible for the safety of these persons.

Moreover, children must be under surveillance to ensure that they do

not play with the product.

It is the operator’s responsibility to ensure that there is free space for

the application to move without risk for the operator or bystanders

before operating the application.

Misuse

Do not overload the actuators – this can cause danger of personal

injury and damage to the system.

Do not use the actuator system for lifting persons. Do not sit or stand

on a table while operating – risk of personal injury.

Do not use the system in environments other than the intended

indoor use.

This device complies with Industry Canada licence-exempt RSS standard(s).

Operation is subject to the following two conditions:

(1) this device may not cause interference, and (2) this device must accept any

interference, including interference that may cause undesired operation of the

device.

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux

appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions

suivantes :

(1) l’appareil nedoit pas produire de brouillage, et

(2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même

si le brouillage est susceptible d’en compromettre le fonctionnement.

Labeling Requirements:

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

Informations importantes

Les informations importantes sur les produits LINAK

peuvent être trouvées dans les

rubriques suivantes:

Géneral

Le non respect de ces instructions peut entraîner des accidents impliquant des

blessures graves.

Ne pas suivre ces instructions peut entraîner l´endommagement ou destruction du

produit. L´utilisation en toute sécurité du système n´est possible que si l´intégralité

des instructions ont été lues et ont été strictement suivies.

Le non respect de se conformer aux instructions marquées du symbole

“note” peut entraîner de graves dommages au système ou à un de ses

composants.

Il est important pour tout individu qui connecte, installe, ou utilise le système

d´avoir les informations nécessaires et l´accès à ce mannuel d´utilisation.

Suivez les instructions pour le montage – risque de blessure si ces instructions

ne sont pas suivies.

L´appareil n´est pas destiné à être utilisé par des enfants ou des personnes

handicapées sans surveillance.

S´il y a des dommages visibles sur le produit, l´installation ne doit pas être

effectuée.

Prendre en compte lors de la construction du matériel, dans lequel

l´actionneur est incorporé, qu´il ne doit y avoir aucune possibilité de

blessures corporelles, telles que la compression des doigts ou des bras.

Consignes de sécurité

Attention!

Le non respect de ces instructions peut entraîner des accidents impliquant des

blessures graves.

Ne pas suivre ces instructions peut entraîner l´endommagement ou destruction du

produit.

Assurez un espace libre autours du materiel pour éviter tout blocage.

Seulement pour les marchés au sein de l´UE:

Cet appareil peut-être utilisé par des enfants âgés de 8 ans et plus, ainsi

que les personnes dont les capacités physiques, sensorielles ou mentales

sont réduites ou ayant un manque d´expérience et de connaissance si elles ont

bénéficié d´une surveillance ou d´instructions concernant l´utilisation de l´appareil

en toute sécurité et compris les risques encourus.

Les enfants ne doivent pas jouer avec l´appareil. Le nettoyage et l´entretien

ne doivent pas être rèalisés par des enfants sans surveillance.

Seulement pour les marchés hors UE.

Les personnes qui n´ont pas l´expérience ou les connaissances nécessaires

sur le ou les produit(s) ne doivent pas le ou les utiliser. Par ailleurs, les

personnes ayant des capacités physiques, sensorielles ou mentales réduites ne

doivent pas utiliser le ou les produit(s), sauf si elles sont sous surveillance ou ont

suivi une formation approfondie de l´utilisation de l´appareil par l´individu

responsable de la securité de ces personnes.

De plus, les enfants doivent-être sous surveillance afin de s´assurer qu´ils

ne jouent pas avec le produit.

Utilisation abusive:

Ne surchargez pas les actionneurs – cela peut engendrer un risque de

blessures corporelles et endommager le système.

Ne pas utiliser les actionneurs pour soulever des personnes. Ne pas

s´asseoir ou se tenir debout sur une table en fonctionnement – risque de

blessures.

Ne pas utiliser le système dans dans des environnements autres que

l´utilisation intérieure prévue.

Repairs

In order to avoid the risk of malfunction, all DESKLINE

repairs must only be carried out by authorised LINAK

workshops or repairers, as special tools must be used and special gaskets must be fitted. Lifting units under warranty

must also be returned to authorised LINAK workshops.

DECLARATION OF INCORPORATION OF PARTLY COMPLETED MACHINERY

LINAK A/S

Smedevænget 8

DK - 6430 Nordborg

Herewith declares that LINAK DESKLINE

products as characterized by the following models and types:

Control Boxes

CBD6S

Linear Actuators

DB5, DB6, DB7, DB9, DB12, DB14, DB16, LA23, LA31

Lifting Columns

DL1A, DL2, DL4S, DL5, DL6, DL7, DL8, DL9, DL10, DL11, DL12, DL14,

DL15,

DL16, DL17, DL19, BASE1

Desk Panels

DPA, DPB, DPH, DPF, DPG1K, DPG1M, DPG1B, DPG1C, DPT, DP1,

DP1CS,

DP1K, DP1V, DP1U

RF Controls

HB10RF, HB20RF, RFT, RFRL

Accessories

BA001, SLS, Kick & Click

comply with the following parts of the Machinery Directive 2006/42/EC, ANNEX I, Essential health and safety

requirements relating to the design and construction of machinery:

1.5.1 Electricity supply

The relevant technical documentation is compiled in accordance with part B of Annex VII and that this

documentation or part hereof will be transmitted by post or electronically to a reasoned request by the national

authorities.

This partly completed machinery must not be put into service until the final machinery into which it

is to be incorporated has been declared in conformity with the provisions of the Machinery

Directive 2006/42/EC where appropriate.

Nordborg, 2017-12-08

LINAK A/S

John Kling, B.Sc.E.E.

Certification and Regulatory Affairs

Authorized to compile the relevant technical documentation

Warning!

If any of the DESKLINE

products are opened, there will be a risk of subsequent malfunction.

Warning!

The DESKLINE

systems do not withstand cutting oil.

Misc. on the DESKLINE

DL8IC/DL9IC/DL10IC/DL11IC system

This system is a DESKLINE system developed for desks and for indoor use in offices. Do not use it in industrial

kitchens or in other enviroments that have to be cleaned with aggressive detergents.

Do not bolt the legs to the floor so that free movement is prevented. This could cause serious damage to the legs in

fault situations.

Warranty - 60 months on DESKLINE

This will be valid for all DESKLINE

products produced after the 1

of May 2015.

Products produced before 1

of May 2015 will still be covered by 36 months.

Products used in DESKLINE application: If these products are used in another application, they will be covered by 18

months warranty.

If there is any doubt that returned products are within the warranty period it is to be treated as if they are covered

by the warranty. We recommend that you use the date of the Control box or actuator as reference if possible. We

will have our purchase no. printed on the label.

Maintenance

Clean dust and dirt on the outside of the system at appropriate intervals and inspect them for damage and

breaks. Inspect the connections, cables, and plugs and check for correct functioning as well as fixing points.

Service of double-insulated products:

Class II

A Class II or double insulated electrical appliance is one which has been designed in such a way that it does not

require a safety connection to electrical earth (US: ground).

The basic requirement is that no single failure can result in dangerous voltage becoming exposed so that it might

cause an electric shock and that this is achieved without relying on an earthed metal casing. This is usually achieved

at least in part by having two layers of insulating material surrounding live parts or by using reinforced insulation.

There is no earthing/grounding means provided on the product, and no earthing/grounding means is to be added to

the product.

In Europe, a double insulated appliance must be labelled “Class II”, “double insulated” or bear the double insulation

symbol (a square inside another square).

Servicing a double-insulated product requires extreme care and knowledge of the system, and is to be done only by

qualified service personnel. Replacement parts for a double-insulated product must be identical to the parts they

replace.

The cleaners and disinfectants must not be highly alkaline or acidic (pH value 6-8).

ETL-marking

Due to space limitations, the complete ETL-marking demands are not represented on the marking plates.

The full ETL Recognized Component markings are shown here.

C/N 120690

Conforms to UL962