Verkada BH61 Guide d'installation

Marque: Verkada

Modèle: BH61

Taper: Guide d'installation

Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401

[email protected]

All specifications are subject to change without notice

Install Guide

BH61 Wireless Alarm Hub

Document

Document Details

Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401

[email protected]

All specifications are subject to change without notice

V1.2 (20220518)

(V1.0 first published 20210929)

Firmware

Firmware version can be verified on

Verkada Command command.verkada.com.

Introduction

What’s in the box

What you’ll need

●A working internet connection

●802.3af / 802.3at POE Power over

Ethernet (PoE) switch, or a PoE injector*

●A smartphone or laptop

●A Phillips screwdriver or power drill with a

Phillips driver bit

●¼ inch (6.5mm) drill bit for wall anchors

● ⅛ inch (3mm) drill bit for pilot holes

●3/16 inch (4.5mm) drill bit for machine

screws

*To reduce potential safety issues, only use the PoE

adapter provided with the product, a replacement PoE

adapter provided by Verkada, or a PoE adapter

purchased as an accessory from Verkada.

Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401

[email protected]

All specifications are subject to change without notice

BH61 Wireless Alarm Hub

Mount plate

(Attached to hub)

Mounting template

3 M4 x 50mm machine screws,

wing nuts, and washers

4 wall anchors T10 Security Torx screwdriver4 M4 x

25mm PH2

wall screws

Connect

For easy registration and setup, scan the QR

code on the product.

If you prefer to manually register your product,

please proceed to: verkada.com/start

Introduction

Sensor overview

Placement

To ensure a reliable connection with your

sensors, mount the BH61 Wireless Alarm Hub in

a location that minimizes the number of walls

and other obstructions between the hub and

the wireless sensors.

Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401

[email protected]

All specifications are subject to change without notice

LED

LED Behavior

Solid Orange

Hub is on and booting up.

Flashing Orange

Hub is updating firmware.

Flashing Blue

Hub can receive events but cannot

reach the server.

Solid Blue

Hub is running, connected, and

receiving events.

Installation

Connect

Use the provided T10 Torx security

screwdriver to loosen the screws and

lift the top cover off the hub.

Connect the hub to an 802.3af/at Power

over Ethernet (PoE) port on your network.

Please note: Your BH61 Wireless Alarm Hub includes

an integrated backup battery. The Hub must be

connected for eight hours before the battery is fully

charged.

Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401

[email protected]

All specifications are subject to change without notice

For easy registration and setup, scan

the QR code on the product.

If you prefer to manually register your

product, please proceed to:

verkada.com/start

Installation

Mounting 1/2

To remove the mount plate, loosen the

mount plate screws and twist the

device counterclockwise. Lift the

device vertically off the base plate

and set aside.

Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401

[email protected]

All specifications are subject to change without notice

Use the provided mounting

template to mark wall mount

holes. For a junction box mount,

use the mounting template to

determine the correct hole

pattern.

For a solid material like wood or metal,

drill ⅛ inch pilot holes. Drive mounting

screws directly into the pilot holes.

For drywall, drill ¼ inch holes. Insert

plastic anchors into holes and drive

mounting screws into anchors.

Installation

Mounting 2/2

Place the hub over the mount plate

screws and twist clockwise. Tighten

the mount plate screws with a Phillips

screwdriver.

Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401

[email protected]

All specifications are subject to change without notice

Replace the hub cover and

secure it using the provided T10

Torx security screwdriver.

Installation

Grounding

In order to attach the ground cable to the

hub, perform the following:

Align a 20AWG or larger grounding cable with

a ring terminal and drive an M4-0.7 x 6mm

screw (not included) through the terminal

and into the threaded grounding point on the

back of the device as shown on the right.

Attach the other terminal of a grounding

cable directly to a circuit breaker, ground rod

or earth ground.

This unit is powered by PoE through a UL Listed ITE.

Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401

[email protected]

All specifications are subject to change without notice

Ground

Appendix

BH61 Compliance

Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401

[email protected]

All specifications are subject to change without notice

FCC

Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to

Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference when the equipment is operated in a residential environment. These limits are designed to

provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to radio communications. However, there is

no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the equipment off and on, the

user is encouraged to try to correct the interference by one or more of the following measures:

●Reorient or relocate the receiving antenna.

●Increase the separation between the equipment and receiver.

●Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

●Consult the dealer or an experienced radio/TV technician for help.

To assure continued compliance, any changes or modifications not expressly approved by the party

responsible for compliance may void the user’s authority to operate his equipment. (Example – use only

shielded interface cables when connecting to computer or peripheral devices)

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may cause undesired

operation.

IMPORTANT NOTE:

Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This

equipment should be installed and operated with a minimum distance 20cm between the radiator & your

body. This transmitter must not be co-located or operating in conjunction with any other antenna or

transmitter.

Statement

This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two

conditions:

(1) This device may not cause interference;

(2) This device must accept any interference, including interference that may cause undesired operation of

the device.

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de

licence. L’exploitation est autorisée aux deux conditions suivantes :

(1) l’appareil ne doit pas produire de brouillage;

(2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est

susceptible d’en compromettre le fonctionnement.

The device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and compliance

with RSS-102 RF exposure, users can obtain Canadian information on RF exposure and compliance.

Le dispositif rencontre l'exemption des limites courantes d'évaluation dans la section 2.5 de RSS 102 et la

conformité à l'exposition de RSS-102 rf, utilisateurs peut obtenir l'information canadienne sur l'exposition et la

conformité de rf.

This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This

equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator

and your body.

Cet émetteur ne doit pas être Co-placé ou ne fonctionnant en même temps qu'aucune autre antenne ou

émetteur. Cet équipement devrait être installé et actionné avec une distance minimum de 20 centimètres

entre le radiateur et votre corps.

Appendix

BH61 Compliance

Caution 1. Maintenance and repair work must always be carried out by qualified technical personnel.

Disconnect power from the unit when performing a maintenance task.

2. Wiring methods used for the connection of the equipment to earth shall be in accordance with the

National Electrical Code, ANSI/NFPA 70, and the Canadian Electrical Code, Part 1, CSA C22.1.

3. The product must be installed and protected in a location that is not easily accessible and is away

from impacts or heavy vibration.

4. The device is only to be connected to PoE networks without routing to outside plants.

5. If powered by a power adapter, the adapter should be properly grounded.

6. Please contact certified dealers for power adapters.

Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401

[email protected]

All specifications are subject to change without notice

Appendix

Support

Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401

[email protected]

All specifications are subject to change without notice

Thank you for purchasing this Verkada product. If for any reason

things don’t work right, or you need assistance, please contact us

immediately.

verkada.com/support

Sincerely, The Verkada Team

Verkada BH61 Guide d'installation

Marque: Verkada

Modèle: BH61

Taper: Guide d'installation

Télécharger le PDF

rapport

dans d''autres langues

English: Verkada BH61 Installation guide

Verkada BH61 Guide d'installation

Verkada BH61 Guide d'installation

dans d''autres langues

Documents connexes

Autres documents