Bestway SaluSpa 60066 Le manuel du propriétaire

SaluSpa 60066
Bestway
Marque
Bestway
Modèle
SaluSpa 60066
Catégorie
Masseurs
Taper
Le manuel du propriétaire
OWNER’S MANUAL EN
VISIT BESTWAY YOUTUBE CHANNEL
IMPORTANT SAFETY INSTRUCTIONS pg 003
PRE-SETUP CHECK LIST pg 007
INSTALLATION pg 009
SET-UP INSTRUCTION IN WINTER pg 009
USING THE SPA pg 012
MAINTENANCE pg 015
DISASSEMBLY AND STORAGE pg 017
TROUBLESHOOTING pg 019
ERROR CODES pg 020
FOR INSTRUCTION VIDEOS
PLEASE VISIT:
BESTWAYCORP.COM/SUPPORT
CONTENTS
WE SUGGEST NOT TO RETURN
THE PRODUCT TO THE STORE
QUESTIONS? PROBLEMS?
MISSING PARTS?
For FAQ, Manuals, Videos Or
spare Parts, Please Visit
bestwaycorp.com/support
V
i
s
i
t
w
w
w
.
b
e
s
t
w
a
y
c
o
r
p
.
c
o
m
/
s
u
p
p
o
r
t
f
o
r
h
e
l
p
2
IMPORTANT SAFETY INSTRUCTIONS
WARNING
IMPORTANT SAFETY INSTRUCTIONS
When using this electrical equipment, basic safety precautions should always be
followed, including the following:
READ AND FOLLOW ALL
INSTRUCTIONS.
WARNING – To reduce the risk of injury, do not permit children to use this product
unless they are closely supervised at all times.
A wire connector is provided on this unit to connect a minimum 6 AWG (13.3 mm
2
)
solid copper conductor between this unit and any metal equipment, metal enclosures
of electrical equipment, metal water pipe, or conduit within 5 feet (1.5 m) of the unit.
DANGER – Risk of injury.
a) Replace damaged cord immediately.
b) Do not bury cord.
c) Connect to a grounded, grounding type receptacle only.
WARNING – This product is provided with a ground-fault circuit-interrupter integrated
with the power plug at the end of the cord. The GFCI must be tested before each
use. With the product operating, push the test button on the GFCI and the product
should not operate. Push the reset button on the GFCI and the product should now
operate normally. When the product fails to operate in this manner, there is a ground
current flowing indicating the possibility of an electrical shock. Disconnect the power
until the fault has been identified and corrected.
DANGER – Risk of Accidental Drowning. Extreme caution must be exercised to
prevent unauthorized access by children. To avoid accidents, ensure that children
cannot use this spa unless they are supervised at all times.
DANGER – Risk of Injury. The suction fittings in this spa are sized to match the
specific water flow created by the pump. Should the need arise to replace the suction
fittings or the pump, be sure that the flow rates are compatible. Never operate spa if
the suction fittings are broken or missing. Never replace a suction fitting with one
rated less than the flow rate marked on the original suction fitting.
DANGER – Risk of Electric Shock. Install at least 5 feet (1.5 m) from all metal
surfaces. As an alternative, a spa may be installed within 5 feet of metal surfaces if
each metal surface is permanently connected by a minimum 6 AWG (13.3 mm
2
) solid
copper conductor to the wire connector on the terminal box that is provided for this
purpose.
DANGER – Risk of Electric Shock. Do not permit any electric appliance, such as a
light, telephone, radio, or television, within 5 feet (1.5 m) of a spa.
WARNING – To reduce the risk of injury:
a) The water in a spa should never exceed 104°F (40°C). Water temperatures
between 100°F (38°C) and 104°F (40°C) are considered safe for a healthy adult.
Lower water temperatures are recommended for young children and when spa
use exceeds 10 minutes.
b) Since excessive water temperatures have a high potential for causing fetal
damage during the early months of pregnancy, pregnant or possibly pregnant
women should limit spa water temperatures to100°F (38°C).
c) Before entering a spa, the user should measure the water temperature with an
accurate thermometer since the tolerance of water temperature-regulating devices
varies.
d) The use of alcohol, drugs, or medication before or during spa use may lead to
unconsciousness with the possibility of drowning.
e) Obese persons and persons with a history of heart disease, low or high blood
pressure, circulatory system problems, or diabetes should consult a physician
before using a spa.
f) Persons using medication should consult a physician before using a spa since
some medication may induce drowsiness while other medication may affect heart
rate, blood pressure, and circulation.
WARNING: TO AVOID ELECTRIC SHOCK, DO NOT USE THE SPA WHEN IT IS
RAINING.
WARNING: Water attracts children; Always attach a spa cover after each use.
WARNING: TO REDUCE THE RISK OF INJURY: Never add water that is higher than
104°F (40°C) into the Spa.
CONSULT YOUR PHYSICIAN FOR
RECOMMENDATIONS.
CAUTION:
We strongly recommend not to unfold and inflate the spa if the ambient temperature
is below 59°F(15°C). We suggest inflating the spa indoors, and then continuing set
up outdoors. If the outdoor temperature is lower than 42.8°F(6°C), the spa heater
must always be on. In this mode, the Freeze Shield™ system can keep the internal
temperature between 42.8°F(6°C) and 50°F(10°C) to prevent damage, such as water
freezing in the pipes or the circulation system.
IMPORTANT:
If the Freeze Shield™ system isn’t working, alarms will pop up on the
spa. Be sure to check the status of your spa if the outdoor temperature is below
42.8°F(6°C). In case of a long-term absence from home when there is a risk of
temperatures falling below 42.8°F(6°C), we strongly suggest disassembling the spa
and storing it following the storage procedure.
CAUTION: Do not use the spa alone.
CAUTION: Always enter and exit the spa slowly and cautiously. Wet surfaces are
slippery.
CAUTION: To avoid damage to the pump, the spa must never be operated unless
the spa is filled with water.
CAUTION: Immediately leave spa if the user feels uncomfortable or sleepy.
NOTE: Please examine equipment before use. Notify Bestway
®
at the customer
service address listed on this manual for any damaged or missing parts at the time of
purchase. Verify that the equipment components represent the model that you had
intended to purchase.
SAVE THESE INSTRUCTIONS
WARNING: CHILDREN SHOULD NOT USE SPAS OR HOT TUBS WITHOUT
ADULT SUPERVISION.
WARNING: DO NOT USE SPAS OR HOT TUBS UNLESS ALL SUCTION GUARDS
ARE INSTALLED TO PREVENT BODY AND HAIR ENTRAPMENT.
WARNING: PEOPLE USING MEDICATIONS AND/OR HAVING AN ADVERSE
MEDICAL HISTORY SHOULD CONSULT A PHYSICIAN BEFORE USING A SPA OR
HOT TUB.
WARNING: PEOPLE WITH INFECTIOUS DISEASES SHOULD NOT USE A SPA
OR HOT TUB.
WARNING: TO AVOID INJURY, EXERCISE CARE WHEN ENTERING OR EXITING
THE SPA OR HOT TUB.
WARNING: DO NOT USE DRUGS OR ALCOHOL BEFORE OR DURING THE USE
OF A SPA OR HOT TUB TO AVOID UNCONSCIOUSNESS AND POSSIBLE
DROWNING.
WARNING: PREGNANT OR POSSIBLY PREGNANT WOMEN SHOULD CONSULT
A PHYSICIAN BEFORE USING A SPA OR HOT TUB.
WARNING: WATER TEMPERATURE IN EXCESS OF 38°C (100°F) CAN BE
INJURIOUS TO YOUR HEALTH.
WARNING: BEFORE ENTERING THE SPA OR HOT TUB, MEASURE THE WATER
TEMPERATURE WITH AN ACCURATE THERMOMETER.
WARNING: DO NOT USE A SPA OR HOT TUB IMMEDIATELY FOLLOWING
STRENUOUS EXERCISE.
WARNING: PROLONGED IMMERSION IN A SPA OR HOT TUB CAN BE
INJURIOUS TO YOUR HEALTH.
WARNING: DO NOT PERMIT ELECTRIC APPLIANCES (SUCH AS A LIGHT,
TELEPHONE, RADIO, OR TELEVISION) WITHIN 1.5 M OF THIS SPA OR HOT TUB.
CAUTION: MAINTAIN WATER CHEMISTRY IN ACCORDANCE WITH
MANUFACTURER'S INSTRUCTIONS.
3
WARNING
IMPORTANT SAFETY INSTRUCTIONS
When using this electrical equipment, basic safety precautions should always be
followed, including the following:
READ AND FOLLOW ALL
INSTRUCTIONS.
WARNING – To reduce the risk of injury, do not permit children to use this product
unless they are closely supervised at all times.
A wire connector is provided on this unit to connect a minimum 6 AWG (13.3 mm
2
)
solid copper conductor between this unit and any metal equipment, metal enclosures
of electrical equipment, metal water pipe, or conduit within 5 feet (1.5 m) of the unit.
DANGER – Risk of injury.
a) Replace damaged cord immediately.
b) Do not bury cord.
c) Connect to a grounded, grounding type receptacle only.
WARNING – This product is provided with a ground-fault circuit-interrupter integrated
with the power plug at the end of the cord. The GFCI must be tested before each
use. With the product operating, push the test button on the GFCI and the product
should not operate. Push the reset button on the GFCI and the product should now
operate normally. When the product fails to operate in this manner, there is a ground
current flowing indicating the possibility of an electrical shock. Disconnect the power
until the fault has been identified and corrected.
DANGER – Risk of Accidental Drowning. Extreme caution must be exercised to
prevent unauthorized access by children. To avoid accidents, ensure that children
cannot use this spa unless they are supervised at all times.
DANGER – Risk of Injury. The suction fittings in this spa are sized to match the
specific water flow created by the pump. Should the need arise to replace the suction
fittings or the pump, be sure that the flow rates are compatible. Never operate spa if
the suction fittings are broken or missing. Never replace a suction fitting with one
rated less than the flow rate marked on the original suction fitting.
DANGER – Risk of Electric Shock. Install at least 5 feet (1.5 m) from all metal
surfaces. As an alternative, a spa may be installed within 5 feet of metal surfaces if
each metal surface is permanently connected by a minimum 6 AWG (13.3 mm
2
) solid
copper conductor to the wire connector on the terminal box that is provided for this
purpose.
DANGER – Risk of Electric Shock. Do not permit any electric appliance, such as a
light, telephone, radio, or television, within 5 feet (1.5 m) of a spa.
WARNING – To reduce the risk of injury:
a) The water in a spa should never exceed 104°F (40°C). Water temperatures
between 100°F (38°C) and 104°F (40°C) are considered safe for a healthy adult.
Lower water temperatures are recommended for young children and when spa
use exceeds 10 minutes.
b) Since excessive water temperatures have a high potential for causing fetal
damage during the early months of pregnancy, pregnant or possibly pregnant
women should limit spa water temperatures to100°F (38°C).
c) Before entering a spa, the user should measure the water temperature with an
accurate thermometer since the tolerance of water temperature-regulating devices
varies.
d) The use of alcohol, drugs, or medication before or during spa use may lead to
unconsciousness with the possibility of drowning.
e) Obese persons and persons with a history of heart disease, low or high blood
pressure, circulatory system problems, or diabetes should consult a physician
before using a spa.
f) Persons using medication should consult a physician before using a spa since
some medication may induce drowsiness while other medication may affect heart
rate, blood pressure, and circulation.
WARNING: TO AVOID ELECTRIC SHOCK, DO NOT USE THE SPA WHEN IT IS
RAINING.
WARNING: Water attracts children; Always attach a spa cover after each use.
WARNING: TO REDUCE THE RISK OF INJURY: Never add water that is higher than
104°F (40°C) into the Spa.
CONSULT YOUR PHYSICIAN FOR
RECOMMENDATIONS.
CAUTION:
We strongly recommend not to unfold and inflate the spa if the ambient temperature
is below 59°F(15°C). We suggest inflating the spa indoors, and then continuing set
up outdoors. If the outdoor temperature is lower than 42.8°F(6°C), the spa heater
must always be on. In this mode, the Freeze Shield™ system can keep the internal
temperature between 42.8°F(6°C) and 50°F(10°C) to prevent damage, such as water
freezing in the pipes or the circulation system.
IMPORTANT:
If the Freeze Shield™ system isn’t working, alarms will pop up on the
spa. Be sure to check the status of your spa if the outdoor temperature is below
42.8°F(6°C). In case of a long-term absence from home when there is a risk of
temperatures falling below 42.8°F(6°C), we strongly suggest disassembling the spa
and storing it following the storage procedure.
CAUTION: Do not use the spa alone.
CAUTION: Always enter and exit the spa slowly and cautiously. Wet surfaces are
slippery.
CAUTION: To avoid damage to the pump, the spa must never be operated unless
the spa is filled with water.
CAUTION: Immediately leave spa if the user feels uncomfortable or sleepy.
NOTE: Please examine equipment before use. Notify Bestway
®
at the customer
service address listed on this manual for any damaged or missing parts at the time of
purchase. Verify that the equipment components represent the model that you had
intended to purchase.
SAVE THESE INSTRUCTIONS
WARNING: CHILDREN SHOULD NOT USE SPAS OR HOT TUBS WITHOUT
ADULT SUPERVISION.
WARNING: DO NOT USE SPAS OR HOT TUBS UNLESS ALL SUCTION GUARDS
ARE INSTALLED TO PREVENT BODY AND HAIR ENTRAPMENT.
WARNING: PEOPLE USING MEDICATIONS AND/OR HAVING AN ADVERSE
MEDICAL HISTORY SHOULD CONSULT A PHYSICIAN BEFORE USING A SPA OR
HOT TUB.
WARNING: PEOPLE WITH INFECTIOUS DISEASES SHOULD NOT USE A SPA
OR HOT TUB.
WARNING: TO AVOID INJURY, EXERCISE CARE WHEN ENTERING OR EXITING
THE SPA OR HOT TUB.
WARNING: DO NOT USE DRUGS OR ALCOHOL BEFORE OR DURING THE USE
OF A SPA OR HOT TUB TO AVOID UNCONSCIOUSNESS AND POSSIBLE
DROWNING.
WARNING: PREGNANT OR POSSIBLY PREGNANT WOMEN SHOULD CONSULT
A PHYSICIAN BEFORE USING A SPA OR HOT TUB.
WARNING: WATER TEMPERATURE IN EXCESS OF 38°C (100°F) CAN BE
INJURIOUS TO YOUR HEALTH.
WARNING: BEFORE ENTERING THE SPA OR HOT TUB, MEASURE THE WATER
TEMPERATURE WITH AN ACCURATE THERMOMETER.
WARNING: DO NOT USE A SPA OR HOT TUB IMMEDIATELY FOLLOWING
STRENUOUS EXERCISE.
WARNING: PROLONGED IMMERSION IN A SPA OR HOT TUB CAN BE
INJURIOUS TO YOUR HEALTH.
WARNING: DO NOT PERMIT ELECTRIC APPLIANCES (SUCH AS A LIGHT,
TELEPHONE, RADIO, OR TELEVISION) WITHIN 1.5 M OF THIS SPA OR HOT TUB.
CAUTION: MAINTAIN WATER CHEMISTRY IN ACCORDANCE WITH
MANUFACTURER'S INSTRUCTIONS.
4
WARNING
IMPORTANT SAFETY INSTRUCTIONS
When using this electrical equipment, basic safety precautions should always be
followed, including the following:
READ AND FOLLOW ALL
INSTRUCTIONS.
WARNING – To reduce the risk of injury, do not permit children to use this product
unless they are closely supervised at all times.
A wire connector is provided on this unit to connect a minimum 6 AWG (13.3 mm
2
)
solid copper conductor between this unit and any metal equipment, metal enclosures
of electrical equipment, metal water pipe, or conduit within 5 feet (1.5 m) of the unit.
DANGER – Risk of injury.
a) Replace damaged cord immediately.
b) Do not bury cord.
c) Connect to a grounded, grounding type receptacle only.
WARNING – This product is provided with a ground-fault circuit-interrupter integrated
with the power plug at the end of the cord. The GFCI must be tested before each
use. With the product operating, push the test button on the GFCI and the product
should not operate. Push the reset button on the GFCI and the product should now
operate normally. When the product fails to operate in this manner, there is a ground
current flowing indicating the possibility of an electrical shock. Disconnect the power
until the fault has been identified and corrected.
DANGER – Risk of Accidental Drowning. Extreme caution must be exercised to
prevent unauthorized access by children. To avoid accidents, ensure that children
cannot use this spa unless they are supervised at all times.
DANGER – Risk of Injury. The suction fittings in this spa are sized to match the
specific water flow created by the pump. Should the need arise to replace the suction
fittings or the pump, be sure that the flow rates are compatible. Never operate spa if
the suction fittings are broken or missing. Never replace a suction fitting with one
rated less than the flow rate marked on the original suction fitting.
DANGER – Risk of Electric Shock. Install at least 5 feet (1.5 m) from all metal
surfaces. As an alternative, a spa may be installed within 5 feet of metal surfaces if
each metal surface is permanently connected by a minimum 6 AWG (13.3 mm
2
) solid
copper conductor to the wire connector on the terminal box that is provided for this
purpose.
DANGER – Risk of Electric Shock. Do not permit any electric appliance, such as a
light, telephone, radio, or television, within 5 feet (1.5 m) of a spa.
WARNING – To reduce the risk of injury:
a) The water in a spa should never exceed 104°F (40°C). Water temperatures
between 100°F (38°C) and 104°F (40°C) are considered safe for a healthy adult.
Lower water temperatures are recommended for young children and when spa
use exceeds 10 minutes.
b) Since excessive water temperatures have a high potential for causing fetal
damage during the early months of pregnancy, pregnant or possibly pregnant
women should limit spa water temperatures to100°F (38°C).
c) Before entering a spa, the user should measure the water temperature with an
accurate thermometer since the tolerance of water temperature-regulating devices
varies.
d) The use of alcohol, drugs, or medication before or during spa use may lead to
unconsciousness with the possibility of drowning.
e) Obese persons and persons with a history of heart disease, low or high blood
pressure, circulatory system problems, or diabetes should consult a physician
before using a spa.
f) Persons using medication should consult a physician before using a spa since
some medication may induce drowsiness while other medication may affect heart
rate, blood pressure, and circulation.
WARNING: TO AVOID ELECTRIC SHOCK, DO NOT USE THE SPA WHEN IT IS
RAINING.
WARNING: Water attracts children; Always attach a spa cover after each use.
WARNING: TO REDUCE THE RISK OF INJURY: Never add water that is higher than
104°F (40°C) into the Spa.
CONSULT YOUR PHYSICIAN FOR
RECOMMENDATIONS.
CAUTION:
We strongly recommend not to unfold and inflate the spa if the ambient temperature
is below 59°F(15°C). We suggest inflating the spa indoors, and then continuing set
up outdoors. If the outdoor temperature is lower than 42.8°F(6°C), the spa heater
must always be on. In this mode, the Freeze Shield™ system can keep the internal
temperature between 42.8°F(6°C) and 50°F(10°C) to prevent damage, such as water
freezing in the pipes or the circulation system.
IMPORTANT:
If the Freeze Shield™ system isn’t working, alarms will pop up on the
spa. Be sure to check the status of your spa if the outdoor temperature is below
42.8°F(6°C). In case of a long-term absence from home when there is a risk of
temperatures falling below 42.8°F(6°C), we strongly suggest disassembling the spa
and storing it following the storage procedure.
CAUTION: Do not use the spa alone.
CAUTION: Always enter and exit the spa slowly and cautiously. Wet surfaces are
slippery.
CAUTION: To avoid damage to the pump, the spa must never be operated unless
the spa is filled with water.
CAUTION: Immediately leave spa if the user feels uncomfortable or sleepy.
NOTE: Please examine equipment before use. Notify Bestway
®
at the customer
service address listed on this manual for any damaged or missing parts at the time of
purchase. Verify that the equipment components represent the model that you had
intended to purchase.
SAVE THESE INSTRUCTIONS
WARNING: CHILDREN SHOULD NOT USE SPAS OR HOT TUBS WITHOUT
ADULT SUPERVISION.
WARNING: DO NOT USE SPAS OR HOT TUBS UNLESS ALL SUCTION GUARDS
ARE INSTALLED TO PREVENT BODY AND HAIR ENTRAPMENT.
WARNING: PEOPLE USING MEDICATIONS AND/OR HAVING AN ADVERSE
MEDICAL HISTORY SHOULD CONSULT A PHYSICIAN BEFORE USING A SPA OR
HOT TUB.
WARNING: PEOPLE WITH INFECTIOUS DISEASES SHOULD NOT USE A SPA
OR HOT TUB.
WARNING: TO AVOID INJURY, EXERCISE CARE WHEN ENTERING OR EXITING
THE SPA OR HOT TUB.
WARNING: DO NOT USE DRUGS OR ALCOHOL BEFORE OR DURING THE USE
OF A SPA OR HOT TUB TO AVOID UNCONSCIOUSNESS AND POSSIBLE
DROWNING.
WARNING: PREGNANT OR POSSIBLY PREGNANT WOMEN SHOULD CONSULT
A PHYSICIAN BEFORE USING A SPA OR HOT TUB.
WARNING: WATER TEMPERATURE IN EXCESS OF 38°C (100°F) CAN BE
INJURIOUS TO YOUR HEALTH.
WARNING: BEFORE ENTERING THE SPA OR HOT TUB, MEASURE THE WATER
TEMPERATURE WITH AN ACCURATE THERMOMETER.
WARNING: DO NOT USE A SPA OR HOT TUB IMMEDIATELY FOLLOWING
STRENUOUS EXERCISE.
WARNING: PROLONGED IMMERSION IN A SPA OR HOT TUB CAN BE
INJURIOUS TO YOUR HEALTH.
WARNING: DO NOT PERMIT ELECTRIC APPLIANCES (SUCH AS A LIGHT,
TELEPHONE, RADIO, OR TELEVISION) WITHIN 1.5 M OF THIS SPA OR HOT TUB.
CAUTION: MAINTAIN WATER CHEMISTRY IN ACCORDANCE WITH
MANUFACTURER'S INSTRUCTIONS.
NOTE: The warning label must be posted near your spa in a readable position
during using your spa.
1. Take out the warning label from the accessory kit.
2. Carefully peel the warning label.
3. Affix the warning label.
To order the warning label, please contact your local Bestway After Sales Service.
ASSEMBLY: THE PROVIDED WARNING LABEL
WARNING
REDUCE THE RISK OF ELECTROCUTION
1. NEVER PLACE AN ELECTRIC APPLIANCE WITHIN 5 FEET OF SPA.
REDUCE THE RISK OF CHILD DROWNING
1. SUPERVISE CHILDREN AT ALL TIMES.
2. ATTACH SPA COVER AFTER EACH USE.
REDUCE THE RISK OF OVERHEATING
1. CHECK WITH A DOCTOR BEFORE USE IF PREGNANT, DIABETIC, IN
POOR HEALTH, OR UNDER MEDICAL CARE.
2. EXIT IMMEDIATELY IF UNCOMFORTABLE, DIZZY, OR SLEEPY. SPA HEAT
CAN CAUSE HYPERTHERMIA AND UNCONSCIOUSNESS.
3. SPA HEAT IN CONJUNCTION WITH ALCOHOL, DRUGS, OR MEDICATION
CAN CAUSE UNCONSCIOUSNESS.
WHEN PREGNANT,
SOAKING IN HOT WATER FOR LONG PERIODS
CAN HARM YOUR FETUS. MEASURE WATER
TEMPERATURE BEFORE ENTERING.
1. DO NOT ENTER SPA IF WATER IS HOTTER THAN 100°F(38°C)
2. DO NOT STAY IN SPA FOR LONGER THAN 10 MINUTES.
5
NOTE: The warning label must be posted near your spa in a readable position
during using your spa.
1. Take out the warning label from the accessory kit.
2. Carefully peel the warning label.
3. Affix the warning label.
To order the warning label, please contact your local Bestway After Sales Service.
1. Indoor Installation:
Be aware of special requirements if you install the spa indoors.
• Humidity is a natural side effect with SaluSpa installation. First determine the
effects of moisture on exposed wood, paper, etc. in the proposed location. To
minimize these effects, it is best to provide plenty of ventilation to the selected
area. An architect can help determine if more ventilation is needed.
2. Outdoor Installation:
• During filling, draining or when in use, water may spill out of the spa. Therefore the
SaluSpa should be installed near a floor drain.
• Do not leave the spa surface exposed to direct sunlight for long periods of time.
SELECTED LOCATION
IMPORTANT:
Due to the combined weight of the SaluSpa, water, and users, it is
extremely important that the surface where the SaluSpa is installed
is smooth, flat, level and capable of supporting the weight for the entire time the
SaluSpa is installed (not on the carpet or other similar material). If the SaluSpa is
placed on a surface which does not meet these requirements, any damage caused
by improper support is not covered under the manufacturer’s warranty. It is the
responsibility of the SaluSpa owner to assure the integrity of the surface at all times.
GFCI WARNING
IMPORTANT: RISK OF ELECTRIC SHOCK. THE GFCI MUST BE TESTED
BEFORE TURNING ON THE PUMP EACH TIME.
WARNING: The GFCI plug must be tested before each use to avoid risk of electric
shock.
WARNING: Before inserting plug into a power outlet, make sure the current rate of
the power outlet is suitable for the pump.
WARNING: Do not use the pump if this test fails. For assistance, please visit the
support section on our website, www.bestwaycorp.com.
WARNING: Using an extension lead or multi plug adaptor with the spa heater can
cause the plug to overheat, causing damage to the equipment and surrounding
items. The spa is a class I electrical appliance and must be connected directly to a
grounded socket. It is recommended to only use a socket which is resistant to
humidity and capable of high power loading. Regularly check the plug and socket for
signs of damage before using the spa – do not use the spa if the plug or socket is
damaged. If you are unsure about the quality of the electrical supply, please consult
a qualified electrician before use.
6
PRE-SETUP CHECK LIST
PARTS CHECKS
Please examine equipment before use.
Notify Bestway® customer service of any
damaged or missing parts at the time of
purchase. Verify that the equipment
components represent the model that you
had intended to purchase. For reference
please use the diagrams below.
7
BARBADOS AIRJET S100104 (60044)
— 71" x 26" / 1.80 m x 66 cm
2
04
54123GASS17
1
09
F4C009B-02ASS17
1
15
P05346
1
06
P05343
1
11
P05320
6
03
P06265
1
14
P61727ASS18
1
01
P06263
1
07
P05345
1 12
/
2
02
P05333
1
08
P05524
2
13
P61726ASS18
1
05
P6931ASS16
1
10
P00217
1
16
P6609ASS16
1 17
P05771
1
2 - 4 2.3-3.2ºF/h
1.3-1.8ºC/h
320 gal/h
1,211 L/h
0.034-0.055Bar
0.5-0.8PSI
177 gal
669 L
1,572 Lb
713 kg
ZURICH AIRJET S100104 (60066)
— 71" x 26" / 1.80 m x 66 cm
2
04
54123GASS17
1
09
F4C009B-02ASS17
1
15
P05346
1
06
P05343
1
11
P05320
6
03
P06273
1
14
P61727ASS18
1
01
P06267
1
07
P05345
1 12
/
2
02
P05333
1
08
P05524
2
13
P61726ASS18
1
05
P6931ASS16
1
10
P00217
1
16
P6609ASS16
1 17
P06270
1
2 - 4 2.3-3.2ºF/h
1.3-1.8ºC/h
320 gal/h
1,211 L/h
0.034-0.055Bar
0.5-0.8PSI
177 gal
669 L
1,572 Lb
713 kg
8
Water Maintenance
Many pollutants in the water settle on surfaces below the water line. These
pollutants can cause bacterial, algal or fungal growth. It is recommended that spas
are cleaned as regularly as necessary. After a time, tenacious stains or biofilms may
develop on the accessible surfaces below the water line or high concentrations of
salts or unwanted reaction by-products may also occur. Depending on hygienic
condition, cleanliness, visibility, odour, debris and stains, it is recommended to
change the water completely and clean/disinfect the spa. When emptying the spa,
the regulations and the instructions for draining the water shall be observed.
Keeping your spa water clean and chemically balanced is necessary. Simply
cleaning the filter cartridge is not enough for proper maintenance, we recommend
you use pool chemicals to maintain water chemistry and chlorine or bromine tablets
(do not use granules) with the chemical dispenser.
Water quality will be directly related to frequency of use, number of users and
overall maintenance of the spa. The water should be changed every
3 days if there is no chemical treatment being performed with the water.
It is highly recommended to use tap water for spa filling to minimize the influence of
unwanted content, such as minerals. Barefoot areas and relaxing areas shall be
cleaned as well. No cleaning water may flow into the spa or spa water cycle. The
dirt and cleaning agents shall be rinsed carefully to drain in the spa surround.
Note: We recommend you take a shower before using your SaluSpa, as cosmetic
products, lotions, and other residues on the skin can quickly degrade water
quality.To use the chemical dispenser, please follow the below instruction.
It is important to follow these suggestions if you are setting up the spa during the winter
period. This will prevent damage to the PVC material and extend the life of your product
drastically.
•
If the ambient temperature is below 50°F(10°C), we suggest keeping the package
indoor where the temperature is above 59°F(15°C) for at least 2h before inflation. This
will make the spa liner more flexible and easier to set up.
•
Open the package in the same room where the temperature is above 59°F(15°C), and
inflate the spa using the spa heater.
•
Position the spa liner outdoor in the desired position, connect the spa heater and fill
with water.
Important: The water temperature used to fill the spa must be above 42.8°F(6°C),
otherwise when you begin to operate with the spa heater, the E03 alarm will appear.
Important: If the Freeze Shield™ system isn’t working, alarms will pop up on the spa.
Be sure to check the status of your spa if the outdoor temperature is below 42.8°F(6°C).
In case of a long-term absence from home when there is a risk of temperatures falling
below 42.8°F(6°C), we strongly suggest disassembling the spa and storing it following
the storage procedure. When you assemble the spa, the automatic warm function will
turn on. In this condition, the spa can be used when the temperature is lower than
42.8°F(6°C).
INSTALLATION
< 50°F(10°C)
> 59°F(15°C)
> 59°F(15°C)
SET-UP
INSTRUCTION
IN WINTER
123
9
Water Maintenance
Many pollutants in the water settle on surfaces below the water line. These
pollutants can cause bacterial, algal or fungal growth. It is recommended that spas
are cleaned as regularly as necessary. After a time, tenacious stains or biofilms may
develop on the accessible surfaces below the water line or high concentrations of
salts or unwanted reaction by-products may also occur. Depending on hygienic
condition, cleanliness, visibility, odour, debris and stains, it is recommended to
change the water completely and clean/disinfect the spa. When emptying the spa,
the regulations and the instructions for draining the water shall be observed.
Keeping your spa water clean and chemically balanced is necessary. Simply
cleaning the filter cartridge is not enough for proper maintenance, we recommend
you use pool chemicals to maintain water chemistry and chlorine or bromine tablets
(do not use granules) with the chemical dispenser.
Water quality will be directly related to frequency of use, number of users and
overall maintenance of the spa. The water should be changed every
3 days if there is no chemical treatment being performed with the water.
It is highly recommended to use tap water for spa filling to minimize the influence of
unwanted content, such as minerals. Barefoot areas and relaxing areas shall be
cleaned as well. No cleaning water may flow into the spa or spa water cycle. The
dirt and cleaning agents shall be rinsed carefully to drain in the spa surround.
Note: We recommend you take a shower before using your SaluSpa, as cosmetic
products, lotions, and other residues on the skin can quickly degrade water
quality.To use the chemical dispenser, please follow the below instruction.
4 5 6
max
min
MAX.
MIN.
9
7 8
10 11
1312
2
2
3-6 min
P6609ASS16
10
Water Maintenance
Many pollutants in the water settle on surfaces below the water line. These
pollutants can cause bacterial, algal or fungal growth. It is recommended that spas
are cleaned as regularly as necessary. After a time, tenacious stains or biofilms may
develop on the accessible surfaces below the water line or high concentrations of
salts or unwanted reaction by-products may also occur. Depending on hygienic
condition, cleanliness, visibility, odour, debris and stains, it is recommended to
change the water completely and clean/disinfect the spa. When emptying the spa,
the regulations and the instructions for draining the water shall be observed.
Keeping your spa water clean and chemically balanced is necessary. Simply
cleaning the filter cartridge is not enough for proper maintenance, we recommend
you use pool chemicals to maintain water chemistry and chlorine or bromine tablets
(do not use granules) with the chemical dispenser.
Water quality will be directly related to frequency of use, number of users and
overall maintenance of the spa. The water should be changed every
3 days if there is no chemical treatment being performed with the water.
It is highly recommended to use tap water for spa filling to minimize the influence of
unwanted content, such as minerals. Barefoot areas and relaxing areas shall be
cleaned as well. No cleaning water may flow into the spa or spa water cycle. The
dirt and cleaning agents shall be rinsed carefully to drain in the spa surround.
Note: We recommend you take a shower before using your SaluSpa, as cosmetic
products, lotions, and other residues on the skin can quickly degrade water
quality.To use the chemical dispenser, please follow the below instruction.
When inflating, you will notice that air will be expelled from
the area where the air hose connects to the pump, this is
normal for technique requirements.
Important: Don't cover the holes on the base of the
inflation hose. This operation will over inflate the liner and
damage the structure.
Do not use an air compressor to inflate the pool.
Do not drag the pool on rough ground as this may cause
damage to the pool liner. Inflation time for reference only.
GFCI TEST
11
Water Maintenance
Many pollutants in the water settle on surfaces below the water line. These
pollutants can cause bacterial, algal or fungal growth. It is recommended that spas
are cleaned as regularly as necessary. After a time, tenacious stains or biofilms may
develop on the accessible surfaces below the water line or high concentrations of
salts or unwanted reaction by-products may also occur. Depending on hygienic
condition, cleanliness, visibility, odour, debris and stains, it is recommended to
change the water completely and clean/disinfect the spa. When emptying the spa,
the regulations and the instructions for draining the water shall be observed.
Keeping your spa water clean and chemically balanced is necessary. Simply
cleaning the filter cartridge is not enough for proper maintenance, we recommend
you use pool chemicals to maintain water chemistry and chlorine or bromine tablets
(do not use granules) with the chemical dispenser.
Water quality will be directly related to frequency of use, number of users and
overall maintenance of the spa. The water should be changed every
3 days if there is no chemical treatment being performed with the water.
It is highly recommended to use tap water for spa filling to minimize the influence of
unwanted content, such as minerals. Barefoot areas and relaxing areas shall be
cleaned as well. No cleaning water may flow into the spa or spa water cycle. The
dirt and cleaning agents shall be rinsed carefully to drain in the spa surround.
Note: We recommend you take a shower before using your SaluSpa, as cosmetic
products, lotions, and other residues on the skin can quickly degrade water
quality.To use the chemical dispenser, please follow the below instruction.
A. LOCK/UNLOCK BUTTON: The pump has a 5-minute auto-lock, this
light will turn on. To lock or unlock the pump, place a finger over the
lock/unlock button for 3 seconds.
B. POWER-SAVING TIMER BUTTON: Designed to help avoid wasting
power by setting the time and duration of the heating cycle for the spa.
This way, you can enjoy your spa at the time you desire, without needing
to leave the heater on at all times.
A
B
C
D
G
E
F
H
I
STEP 1: Set the heating duration
1. Press the button unit the LED starts to flash.
2. Press the or button to adjust the heating duration (From 1-999 hours).
3. Press the button again to confirm the heating duration.
STEP 2: Set the number of hours FROM NOW when the heater will activate
1. After setting the heating duration, the LED starts to flash.
2. Press the or button to adjust the hours until time of activation (From 0-999 hours).
3. Press button again or simply touch nothing for 10 seconds to confirm the setting. The
LED will light steadily, and the countdown to heater activation will begin.
To modify the timer settings: Press the button and use the or button to adjust.
Cancel the setting: Press the button for 2 seconds.
NOTE: After setting, the screen flashes the current temperature and time alternately.
NOTE: Timer adjustment (amount of time with the heater ON) may be set from 1 to 999 hours;
Reservation time adjustment (the number of hours FROM NOW when the heater will begin to
function) may be set from 0 to 999 hours. If the timer is set at 0 hour, the heating system will
activate immediately.
Note that the timer is one time per use - the user sets the duration of the heating cycle, and
how many hours from now the heating cycle begins. The timer does NOT repeat until reset.
USING THE SPA
Hyperthermia occurs when the internal temperature of the body reaches a level
several degrees above the normal body temperature of 98.6°F(37°C). The symptoms
of hyperthermia include an increase in the internal temperature of the body,
dizziness, lethargy, drowsiness, and fainting. The effects of hyperthermia include
failure to perceive heat, failure to recognize the need to exit spa or hot tub,
unawareness of impending hazard, fetal damage in pregnant women, physical
inability to exit the spa or hot tub, and unconsciousness resulting in the danger of
drowning.
WARNING – The use of alcohol, drugs, or medication can greatly increase the risk of
fatal hyperthermia.
WARNING: WATER TEMPERATURE IN EXCESS OF 100°F(38°C) CAN BE
INJURIOUS TO YOUR HEALTH.
C. HEAT BUTTON: Use this button to activate the heating system. When
the light above the heat button is red, the heating system is activated.
When the light is green, the water is at the set temperature and the
heating system is at rest.
NOTE: If the heating system is activated the filtration system will
automatically start.
NOTE: After turning off the heating system the filtration system will
continue to operate.
NOTE: If the spa heater is on when the water temperature is below
42.8°F(6ºC), the heating system will warm the water until 50°F(10ºC)
automatically.
12
Water Maintenance
Many pollutants in the water settle on surfaces below the water line. These
pollutants can cause bacterial, algal or fungal growth. It is recommended that spas
are cleaned as regularly as necessary. After a time, tenacious stains or biofilms may
develop on the accessible surfaces below the water line or high concentrations of
salts or unwanted reaction by-products may also occur. Depending on hygienic
condition, cleanliness, visibility, odour, debris and stains, it is recommended to
change the water completely and clean/disinfect the spa. When emptying the spa,
the regulations and the instructions for draining the water shall be observed.
Keeping your spa water clean and chemically balanced is necessary. Simply
cleaning the filter cartridge is not enough for proper maintenance, we recommend
you use pool chemicals to maintain water chemistry and chlorine or bromine tablets
(do not use granules) with the chemical dispenser.
Water quality will be directly related to frequency of use, number of users and
overall maintenance of the spa. The water should be changed every
3 days if there is no chemical treatment being performed with the water.
It is highly recommended to use tap water for spa filling to minimize the influence of
unwanted content, such as minerals. Barefoot areas and relaxing areas shall be
cleaned as well. No cleaning water may flow into the spa or spa water cycle. The
dirt and cleaning agents shall be rinsed carefully to drain in the spa surround.
Note: We recommend you take a shower before using your SaluSpa, as cosmetic
products, lotions, and other residues on the skin can quickly degrade water
quality.To use the chemical dispenser, please follow the below instruction.
C. HEAT BUTTON: Use this button to activate the heating system. When
the light above the heat button is red, the heating system is activated.
When the light is green, the water is at the set temperature and the
heating system is at rest.
I. WATER FILTER BUTTON: This button turns the filter pump on and off.
The light above the Water Filter Button displays red when activated.
E/G. TEMPERATURE ADJUSTMENT BUTTONS: Pressing the
Temperature Increase or Decrease buttons will cause the LED to flash.
When it is flashing you can adjust to the desired temperature setting. If
you hold these buttons down the values will rapidly increase or decrease.
The new and desired temperature setting will remain on the LED display
for 3 seconds to confirm the new value.
NOTE: The default temperature is 95°F(35°C).
NOTE: Temperature adjustment ranges from 68°F(20°C) to 104°F(40°C).
F. ON/OFF BUTTON: Press this button for 2 seconds to active the control
panel buttons and the light turns to green. Press this button for 2 seconds
to turn off all currently activated functions.
POWER-SAVING TIMER LED:
This flashing LED means you are setting the heating duration. The light will
be on when the heating function starts to work.
This flashing LED means you are setting the number of hours FROM NOW
when the heater will activate. When the light is on, the Power-Saving
Timer function is set.
D. MASSAGE SYSTEM BUTTON: Use this button to activate the
massage system, which has a 30-minute auto-shutoff feature. The light
above the Massage System Button displays red when activated.
IMPORTANT: Do not run the Massage system when the cover is
attached. Air can accumulate inside the spa and cause irreparable
damage to the cover and bodily harm.
NOTE: Heat and massage system work together to create a warm
massage experience.
H. CELSIUS/FAHRENHEIT TOGGLE: The temperature can be displayed
in either Fahrenheit or Celsius.
NOTE: If the heating system is activated the filtration system will
automatically start.
NOTE: After turning off the heating system the filtration system will
continue to operate.
NOTE: If the spa heater is on when the water temperature is below
42.8°F(6ºC), the heating system will warm the water until 50°F(10ºC)
automatically.
NOTE: The WATER HEATER rate may change in the conditions below:
• When the outdoor temperature is below 59°F(15°C).
• If the cover is not in position when the heating function is activated.
NOTE: To display the current water temperature, run the filter system for at least a
minute.
The water temperature as tested by an external thermometer may vary from the
temperature as displayed on the spa panel by as much as approximately 35.6°F(2°C).
13
Water Maintenance
Many pollutants in the water settle on surfaces below the water line. These
pollutants can cause bacterial, algal or fungal growth. It is recommended that spas
are cleaned as regularly as necessary. After a time, tenacious stains or biofilms may
develop on the accessible surfaces below the water line or high concentrations of
salts or unwanted reaction by-products may also occur. Depending on hygienic
condition, cleanliness, visibility, odour, debris and stains, it is recommended to
change the water completely and clean/disinfect the spa. When emptying the spa,
the regulations and the instructions for draining the water shall be observed.
Keeping your spa water clean and chemically balanced is necessary. Simply
cleaning the filter cartridge is not enough for proper maintenance, we recommend
you use pool chemicals to maintain water chemistry and chlorine or bromine tablets
(do not use granules) with the chemical dispenser.
Water quality will be directly related to frequency of use, number of users and
overall maintenance of the spa. The water should be changed every
3 days if there is no chemical treatment being performed with the water.
It is highly recommended to use tap water for spa filling to minimize the influence of
unwanted content, such as minerals. Barefoot areas and relaxing areas shall be
cleaned as well. No cleaning water may flow into the spa or spa water cycle. The
dirt and cleaning agents shall be rinsed carefully to drain in the spa surround.
Note: We recommend you take a shower before using your SaluSpa, as cosmetic
products, lotions, and other residues on the skin can quickly degrade water
quality.To use the chemical dispenser, please follow the below instruction.
Ambient Temperature
50ºF(10ºC)
59ºF(15ºC)
68ºF(20ºC)
77ºF(25ºC)
86ºF(30ºC)
Water Temperature
50ºF(10ºC)
59ºF(15ºC)
68ºF(20ºC)
77ºF(25ºC)
86ºF(30ºC)
Set Temperature
104ºF(40ºC)
104ºF(40ºC)
104ºF(40ºC)
104ºF(40ºC)
104ºF(40ºC)
Heating Duration
25.5 h
21 h
16 h
11.5 h
7.5 h
IMPORTANT
To reach 104°F(40°C), the heating duration required is based on the starting water
temperature and ambient temperature, the data below is purely for reference. To
display the current water temperature, run the filter system for at least a minute.
Power Rate Massage Tube Blower Heat Element Water Pump
11.3A at 20ºC 0.7A
110-120V AC,
60Hz, Single Phase
12A at 20ºC 6.5A
• Be sure to cover the spa with the spa
cover whenever the heating function is
activated. Leaving the spa uncovered
will increase the heating duration
required.
• When the spa is assembled with water,
do not switch off the spa heater if the
temperature is lower than 42.8°F(6ºC).
WINTER USE INSTRUCTIONS
•
You can keep the spa on during winter when the temperature is lower than
42.8°F(
6°C
)
. The Freeze Shield™ system automatically keeps the water temperature
between
42.8°F(
6°C
)
and
50°F(
10°C
)
, and it will prevent the water from freezing.
Important:
If the water temperature is below
42.8°F(
6°C
)
, the spa heater must always
be on. In this mode, the Freeze Shield™ system can keep the internal temperature
between
42.8°F(
6°C
)
and
50°F(
10°C
)
to prevent damage, such as water freezing in the
pipes or the circulation system.
Important:
If the Freeze Shield™ system isn’t working, alarms will pop up on the spa.
Be sure to check the status of your spa if the outdoor temperature is below
42.8°F(
6°C
)
. In case of a long-term absence from home when there is a risk of
temperatures falling below
42.8°F(
6°C
)
, we strongly suggest disassembling the spa
and storing it following the storage procedure.
•
Any damage as a result of using the spa in these conditions is the responsibility of the
customer. Do not use the spa when the ambient temperature reaches 14°F(-10°C).
14
Cover Maintenance
The cover shall be cleaned inside and out periodically using a suitable solution that
includes adequate disinfection (e.g. 10 mg/l of Free Chlorine).
Filter Cartridge Maintenance
To ensure your spa water stays clean, check and clean your filter cartridges every
day follow the steps below.
NOTE: We recommend changing your filter cartridges every week or, if the filter
cartridges remain soiled and discolored, they should be replaced.
CAUTION: You must ensure the pump is unplugged before beginning spa
maintenance to avoid risk of injury or death.
MAINTENANCE
Adding Air: Your spa will require additional air to be added from time to time.
Changes in temperature from day to night will change the pressure in the spa and
may cause a certain amount of deflation. Please follow the assembly instructions and
inflate to the accurate pressure needed.
When you need to use the pump for inflation, please block the hoses to prevent
water from escaping, then disconnect the pump, screw on the cap (P00217) to avoid
water coming out from the air pipe.
P00217
P05524
C
o
n
-
l
o
i
n
5
Filter Set
Filter Cartridge
Water Maintenance
Many pollutants in the water settle on surfaces below the water line. These
pollutants can cause bacterial, algal or fungal growth. It is recommended that spas
are cleaned as regularly as necessary. After a time, tenacious stains or biofilms may
develop on the accessible surfaces below the water line or high concentrations of
salts or unwanted reaction by-products may also occur. Depending on hygienic
condition, cleanliness, visibility, odour, debris and stains, it is recommended to
change the water completely and clean/disinfect the spa. When emptying the spa,
the regulations and the instructions for draining the water shall be observed.
Keeping your spa water clean and chemically balanced is necessary. Simply
cleaning the filter cartridge is not enough for proper maintenance, we recommend
you use pool chemicals to maintain water chemistry and chlorine or bromine tablets
(do not use granules) with the chemical dispenser.
Water quality will be directly related to frequency of use, number of users and
overall maintenance of the spa. The water should be changed every
3 days if there is no chemical treatment being performed with the water.
It is highly recommended to use tap water for spa filling to minimize the influence of
unwanted content, such as minerals. Barefoot areas and relaxing areas shall be
cleaned as well. No cleaning water may flow into the spa or spa water cycle. The
dirt and cleaning agents shall be rinsed carefully to drain in the spa surround.
Note: We recommend you take a shower before using your SaluSpa, as cosmetic
products, lotions, and other residues on the skin can quickly degrade water
quality.To use the chemical dispenser, please follow the below instruction.
15
NOTE: Remove the chemical dispenser from spa when the spa is in use.
IMPORTANT: After performing chemical maintenance and before using the spa, use
a test kit (not included) to test the water chemistry. We recommend maintaining your
water as below table.
Important: Add chemical liquid in small doses and in
the center of the pool avoid directly contact of the
chemical with the spa surface, the direct contact of
chemical with spa material will damage the material
and discolored the surface.
NOTE: Damage resulting from chemical imbalance is not covered by the warranty.
Pool chemicals are potentially toxic and should be handled with care. There are
serious health risks from chemical vapors and the incorrect labeling and storage of
chemical containers. Please consult your local pool supply retailer for more
information about chemical maintenance. Pay close attention to the chemical
manufacturer’s instructions. spa damage resulting from misuse of chemicals and
mismanagement of spa water is not covered by the warranty.
Important: Over usage of chemical will discolored the printing and all points of the
spa material, in worse case damage the structure of the spa liner.
pH
7.4-7.6
Total Alkalinity
80-120ppm
Free Chlorine
2-4ppm
Using chemical tablets (not included):
Using chemical liquid (not included):
Water Maintenance
Many pollutants in the water settle on surfaces below the water line. These
pollutants can cause bacterial, algal or fungal growth. It is recommended that spas
are cleaned as regularly as necessary. After a time, tenacious stains or biofilms may
develop on the accessible surfaces below the water line or high concentrations of
salts or unwanted reaction by-products may also occur. Depending on hygienic
condition, cleanliness, visibility, odour, debris and stains, it is recommended to
change the water completely and clean/disinfect the spa. When emptying the spa,
the regulations and the instructions for draining the water shall be observed.
Keeping your spa water clean and chemically balanced is necessary. Simply
cleaning the filter cartridge is not enough for proper maintenance, we recommend
you use pool chemicals to maintain water chemistry and chlorine or bromine tablets
(do not use granules) with the chemical dispenser.
Water quality will be directly related to frequency of use, number of users and
overall maintenance of the spa. The water should be changed every
3 days if there is no chemical treatment being performed with the water.
It is highly recommended to use tap water for spa filling to minimize the influence of
unwanted content, such as minerals. Barefoot areas and relaxing areas shall be
cleaned as well. No cleaning water may flow into the spa or spa water cycle. The
dirt and cleaning agents shall be rinsed carefully to drain in the spa surround.
Note: We recommend you take a shower before using your SaluSpa, as cosmetic
products, lotions, and other residues on the skin can quickly degrade water
quality.To use the chemical dispenser, please follow the below instruction.
Important: Don't use granulate tablet or throw the tablet directly in the water, the
chemical will deposit on the bottom and damage the material and discolored the PVC.
C
o
n
-
l
o
i
n
5
16
Water Maintenance
Many pollutants in the water settle on surfaces below the water line. These
pollutants can cause bacterial, algal or fungal growth. It is recommended that spas
are cleaned as regularly as necessary. After a time, tenacious stains or biofilms may
develop on the accessible surfaces below the water line or high concentrations of
salts or unwanted reaction by-products may also occur. Depending on hygienic
condition, cleanliness, visibility, odour, debris and stains, it is recommended to
change the water completely and clean/disinfect the spa. When emptying the spa,
the regulations and the instructions for draining the water shall be observed.
Keeping your spa water clean and chemically balanced is necessary. Simply
cleaning the filter cartridge is not enough for proper maintenance, we recommend
you use pool chemicals to maintain water chemistry and chlorine or bromine tablets
(do not use granules) with the chemical dispenser.
Water quality will be directly related to frequency of use, number of users and
overall maintenance of the spa. The water should be changed every
3 days if there is no chemical treatment being performed with the water.
It is highly recommended to use tap water for spa filling to minimize the influence of
unwanted content, such as minerals. Barefoot areas and relaxing areas shall be
cleaned as well. No cleaning water may flow into the spa or spa water cycle. The
dirt and cleaning agents shall be rinsed carefully to drain in the spa surround.
Note: We recommend you take a shower before using your SaluSpa, as cosmetic
products, lotions, and other residues on the skin can quickly degrade water
quality.To use the chemical dispenser, please follow the below instruction.
DISASSEMBLY AND STORAGE
DRAINING THE SPA
3. 4.
5.
NOTE: Dry the spa pool.
1. 2.
17
Water Maintenance
Many pollutants in the water settle on surfaces below the water line. These
pollutants can cause bacterial, algal or fungal growth. It is recommended that spas
are cleaned as regularly as necessary. After a time, tenacious stains or biofilms may
develop on the accessible surfaces below the water line or high concentrations of
salts or unwanted reaction by-products may also occur. Depending on hygienic
condition, cleanliness, visibility, odour, debris and stains, it is recommended to
change the water completely and clean/disinfect the spa. When emptying the spa,
the regulations and the instructions for draining the water shall be observed.
Keeping your spa water clean and chemically balanced is necessary. Simply
cleaning the filter cartridge is not enough for proper maintenance, we recommend
you use pool chemicals to maintain water chemistry and chlorine or bromine tablets
(do not use granules) with the chemical dispenser.
Water quality will be directly related to frequency of use, number of users and
overall maintenance of the spa. The water should be changed every
3 days if there is no chemical treatment being performed with the water.
It is highly recommended to use tap water for spa filling to minimize the influence of
unwanted content, such as minerals. Barefoot areas and relaxing areas shall be
cleaned as well. No cleaning water may flow into the spa or spa water cycle. The
dirt and cleaning agents shall be rinsed carefully to drain in the spa surround.
Note: We recommend you take a shower before using your SaluSpa, as cosmetic
products, lotions, and other residues on the skin can quickly degrade water
quality.To use the chemical dispenser, please follow the below instruction.
CLEANING THE SPA
Detergent residues and dissolved solids from bathing suits and chemicals may build
up on the spa walls. Use soap and water to clean the walls and rinse thoroughly.
NOTE: DO NOT use hard brushes or abrasive cleaners.
Make sure the spa and pump are completely dry. This is essential to extend the life of
the spa. We recommend using the pump to blow dry the spa, pump and pipes.
Remove the filter sets and discard the used filter cartridges. Re-attach the two
stopper caps onto the spa’s inlet and outlet valves. It is recommended you store the
spa in its original package in a warm [above 59°F(15°C)] and dry place.
DEFLATION
Your spa is equipped with a deflation function to remove all the air from inside the
chamber to make it easier to pack and store.
REPAIR
For PVC part.
If the spa is torn or punctured, use the provided underwater adhesive repair patch.
1. Clean area to be repaired.
2. Carefully peel patch.
3. Press patch over area to be repaired.
4. Wait 30 seconds before inflation.
For Tritech PVC material.
If the spa is torn or punctured, use the provided PVC repair patch and glue (not included) following these steps:
1. Clean and dry area to be repaired.
2. Cut the provided PVC patch to appropriate size.
3. Use glue (not included) to coat the one side of the newly cut patch. Make sure the glue is evenly distributed.
4. Wait for 30 seconds and then place the cut patch with glue over the damaged area.
5. Smooth out any bubbles of air that may be trapped underneath, and press firmly for two minutes.
6. The product is once again ready for use. Repeat this process should further leaks occur.
7. Wait 30 minutes before inflation.
Screw valve P61727ASS18
P61726ASS18
18
Problems Probable Causes Solutions
The control panel has an auto-lock,
which is activated after 5 minutes of
inactivity. The LED display has one
icon: If the lock icon is highlighted,
the control panel is locked.
- Control panel is not activated.
Water leaks from the adapters
between the pump and spa
What kind of chemicals should be
used for water maintenance?
GFCI test failed
Control panel not working
Water is not clean
Spa pool leakage
Pump adapters are not level with
the spa adapters
Massage System does not work
Pump does not heat properly
Pump does not operate - Power failure
- GFCI broken
- Check power source
- For assistance, please visit the support section on our website,
www.bestwaycorp.com.
- Set to a higher temperature refer to section pump operation
- Clean/replace the filter cartridge refer to section filter cartridge cleaning
and replacement
- Unplug the pump, and put the plug in a dry, cool place. Only
restart the pump when the water temperature reaches 95°F(35°C) or
lower
- Attach the cover.
- For assistance, please visit the support section on our website,
www.bestwaycorp.com.
- Unplug the pump and wait two hours until the pump has cooled. Insert
the plug and press the massage system button
- Press the massage system button to reactivate
- For assistance, please visit the support section on our website,
www.bestwaycorp.com.
- Elevate the pump with wood or another type of insulated material to
bring the pump's adapters level with the spa's adapters
- Use provided repair patch
- Using soapy water, cover the air-valve to check if air is leaking, if so,
use the provided wrench to fasten the air-valve following these steps:
1. Deflate the spa.
2. With one hand, hold the backside of the air valve from the inner
side of the spa wall and turn the wrench clockwise.
- Increase filtration time
- Clean/replace the Filter Cartridge (refer to Filter Cartridge Cleaning and
Replacement section)
- Refer to the chemical manufacturer’s instructions
- To unlock the control panel, press the button for 3 seconds.
If the control panel will not unlock, restart the pump – unplug and
plug in the pump.
- Press the on/off button for 2 seconds. If the problem persists,
for assistance, please visit the support section on our website,
www.bestwaycorp.com.
For assistance, please visit the support section on our website,
www.bestwaycorp.com.
- Insert the stopper caps on the spa ports to prevent the water from
escaping and disconnect the pump. Check if the seals are in place.
- If the seals are not in the correct positionopen the gearsand place the
seals in correct position.
- If the seals are damaged, they must be replaced. For assistance,
please visit the support section on our website
www.bestwaycorp.com.
- If the seals are in correct positionthe adapters are not tightened
correctly. Connect the pump to the spa, hand-tighten the adaptersand
remove the stopper caps from the spa ports. If there is leakage, tighten
the adapter until there is no leakage.
- Temperature set too low
- Dirty Filter Cartridge
- The thermal cut-out cut off
- Spa is not covered
- Heating element failed
- Air Pump is overheating
- The massage system
stops automatically
- Air pump is broken
- One characteristic of PVC is that it
changes shape, which is normal
- Spa is torn or punctured
- Air valve is loose
- Insufficient filtering time
- Dirty Filter Cartridge
- Improper water maintenance
There is a defect in your spa
Please consult your local chemical supplier for information about chemical maintenance.
Pay close attention to the chemical manufacturer’s instructions.
- Seals are missing inside the pump
adapters
- Seals are not in correct position
- Seals are damaged
- Adapters are not tightened correctly
Water Maintenance
Many pollutants in the water settle on surfaces below the water line. These
pollutants can cause bacterial, algal or fungal growth. It is recommended that spas
are cleaned as regularly as necessary. After a time, tenacious stains or biofilms may
develop on the accessible surfaces below the water line or high concentrations of
salts or unwanted reaction by-products may also occur. Depending on hygienic
condition, cleanliness, visibility, odour, debris and stains, it is recommended to
change the water completely and clean/disinfect the spa. When emptying the spa,
the regulations and the instructions for draining the water shall be observed.
Keeping your spa water clean and chemically balanced is necessary. Simply
cleaning the filter cartridge is not enough for proper maintenance, we recommend
you use pool chemicals to maintain water chemistry and chlorine or bromine tablets
(do not use granules) with the chemical dispenser.
Water quality will be directly related to frequency of use, number of users and
overall maintenance of the spa. The water should be changed every
3 days if there is no chemical treatment being performed with the water.
It is highly recommended to use tap water for spa filling to minimize the influence of
unwanted content, such as minerals. Barefoot areas and relaxing areas shall be
cleaned as well. No cleaning water may flow into the spa or spa water cycle. The
dirt and cleaning agents shall be rinsed carefully to drain in the spa surround.
Note: We recommend you take a shower before using your SaluSpa, as cosmetic
products, lotions, and other residues on the skin can quickly degrade water
quality.To use the chemical dispenser, please follow the below instruction.
TROUBLESHOOTING
Bestway strives to provide the most trouble-free spas on the market.
If you experience any problems whatsoever, do not hesitate to contact Bestway or your authorized dealer. Here are some
helpful tips to help you to diagnose and rectify some common sources of trouble.
19
Water Maintenance
Many pollutants in the water settle on surfaces below the water line. These
pollutants can cause bacterial, algal or fungal growth. It is recommended that spas
are cleaned as regularly as necessary. After a time, tenacious stains or biofilms may
develop on the accessible surfaces below the water line or high concentrations of
salts or unwanted reaction by-products may also occur. Depending on hygienic
condition, cleanliness, visibility, odour, debris and stains, it is recommended to
change the water completely and clean/disinfect the spa. When emptying the spa,
the regulations and the instructions for draining the water shall be observed.
Keeping your spa water clean and chemically balanced is necessary. Simply
cleaning the filter cartridge is not enough for proper maintenance, we recommend
you use pool chemicals to maintain water chemistry and chlorine or bromine tablets
(do not use granules) with the chemical dispenser.
Water quality will be directly related to frequency of use, number of users and
overall maintenance of the spa. The water should be changed every
3 days if there is no chemical treatment being performed with the water.
It is highly recommended to use tap water for spa filling to minimize the influence of
unwanted content, such as minerals. Barefoot areas and relaxing areas shall be
cleaned as well. No cleaning water may flow into the spa or spa water cycle. The
dirt and cleaning agents shall be rinsed carefully to drain in the spa surround.
Note: We recommend you take a shower before using your SaluSpa, as cosmetic
products, lotions, and other residues on the skin can quickly degrade water
quality.To use the chemical dispenser, please follow the below instruction.
CAUSES REASONS SOLUTIONS
The water flow sensors work
without pressing the filter or heat
button.
1. The water flow sensor flags didn’t fall back into the
correct position.
2. The water flow sensors are broken.
1. Unplug the plug, strike the side of the pump but not violently, and plug it back in.
2. For assistance, please visit the support section on our website,
www.bestwaycorp.com.
After starting or during the
functions of filtering or/and
heating, the water flow sensors do
not detect water flow.
1. You forgot to remove the 2 stopper caps from inside
the pool.
2. Filter cartridges are dirty.
3. Activate the filter or heat system and put your hand
in front of the outlet pipe inside the pool to check if
you can feel water flowing out.
a. If no water flows out the water pump is broken.
b. Water flows out but the alarm oppears, then
the water flow sensors are broken.
4. Filter blockage
5. Bent pipes or poor water flow through the plastic
pipes of the liner
6. Debris screens are blocked: debris screens can
become blocked by hard water due to calcium
build-up.
7. Perished washers
The washers within the spa couplings may have
become perished or worn.
1. Remove the 2 stopper caps before heating, refer to Assembly section in the
User’s Manual.
2. Remove the filter set from inside the pool and push the filter or heat button. If no
alarm appears, clean or change the filter cartridges install the filter set inside the
pool.
3. For assistance, please visit the support section on our website,
www.bestwaycorp.com.
4. Clean the filter and check for damage. Replace or re-install as necessary. For
assistance, please visit the support section on our website,
www.bestwaycorp.com.
5. Please check through the spa connection to see if the pipes are bending. For
assistance, please visit the support section on our website,
www.bestwaycorp.com.
6. Empty the spa and place a garden hose inside the pipes to wash the debris. To
be sure all debris is removed, perform the operation from the outside and inside
of the spa.
Use a toothbrush to remove any stubborn debris.
For assistance, please visit the support section on our website,
www.bestwaycorp.com.
7. Check the washers inside the coupling for damage. Unscrew the couplings and
remove the washer for further inspection.
For assistance, please visit the support section on our website,
www.bestwaycorp.com.
The pump’s thermometer reads
the water temperature below
40°F(4°C).
1. The water temperature is lower than 40°F(4°C).
2. If the water temperature is higher than 44.6°F(7°C),
the pump’s thermometer is broken.
1. The spa is not designed to operate with water temperatures lower than
40°F(4ºC). Unplug the pump and only re-start the pump when the water
temperature reaches 43°F(6°C).
2. For assistance, please visit the support section on our website,
www.bestwaycorp.com.
The pump’s thermometer reads
the water temperature over
119°F(48°C).
1. The water temperature is over 119°F(48°C).
2. The ambient temperature is higher than 104°F(40°C)
or the spa is exposed to direct sunlight for an
extended period of time.
3. If the water temperature is lower than 113°F(45°C),
the pump’s thermometer is broken.
The pump’s thermometer
connections have issues.
1. The pump’s thermometer connectors don’t work
properly.
2. The pump’s thermometer is broken.
For assistance, please visit the support section on our website,
www.bestwaycorp.com.
The thermal cut-out cut off. 1. The ambient temperature is over 122°F(50°C) or
the pump is directly under the sunshine.
2. The thermal cut-out is broken.
1. Unplug the pump, and put the pump in a dry, cool place. Only re-start the
pump when the water temperature reaches 93.2°F(34°C) or lower.
2. For assistance, please visit the support section on our website,
www.bestwaycorp.com.
ERROR CODES
20
1. The spa is not designed to operate with water temperatures greater than
104°F(40°C). Unplug the pump and only re-start the pump when the water
temperature reaches 100°F(38°C) or lower.
2. Disconnect the plug, detach the pump and drain the spa. After 15 minutes,
reattach the pump, reconnect the plug and restart the heating function. If the
alarm appears again, consider moving the spa to another location without
direct sunlight.
3. For assistance, please visit the support section on our website,
www.bestwaycorp.com.
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84

Bestway SaluSpa 60066 Le manuel du propriétaire

SaluSpa 60066
Bestway
Marque
Bestway
Modèle
SaluSpa 60066
Catégorie
Masseurs
Taper
Le manuel du propriétaire
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents