kiddy EVOLUTION PRO 2 Manuel utilisateur

Infant Carrier

INSTRUCTION MANUAL

EN / DE / ES / FR / IT / PT / PL / NL Booklet 1

F

E

B

C

D

G

H

I

K

O

A

P

J

L

M

N

> 6 M

3

1

2

1

2

4

5

1

2

3

1

2

6

7

1

2

8

10

CLICK

9

11 12

14

13

CLICK

1

2

15 16

19

2

1

3

20

A

B

17 18

21

B

A

22

1

CLICK

1

CLICK

23

B

A

24

4

1

2

3

5

Please read these instructions carefully

before using this infant carrier for the rst time.

Keep this manual for future reference.

ENEN

Table of contents

1. Description of components 5

2. Introduction 6

3. Suitability 6

4. General safety instructions 7

5. General use / Adjustments 10

5.1 Functions of the carry handle /

Adjusting the reclined position 10

5.2 Using the newborn inlay 11

5.3 Using the sunshade 11

6. Buckling / Unbuckling of the baby 11

6.1 Loosening the belt system 11

6.2 Adjusting the height of the belt system 11

6.3 Buckling / Unbuckling of the baby 12

7. Use in the vehicle 13

7.1 In-vehicle installation with seat belt 13

7.1.1 Seat selection 13

7.1.2 Installation steps with the seat belt 13

7.2 Installation with the Isofix platform 14

7.2.1 Seat selection 14

7.2.2 Installation steps on the Isofix platform 15

7.2.3 Removal from the Isofix platform 15

8. Use on a stroller 16

9. Use as a rocker 16

10. Remove / Replacing the covers 17

10.1 Removing the sunshade 17

10.2 Removing the backrest cover 18

10.3 Removing the seat cover 18

10.4 Replacing covers 18

EN

11. Care and maintenance 18

11.1 Cleaning the seat covers 18

11.2 Cleaning plastic parts 18

11.3 Cleaning the belt system 18

12. Steps to take after an accident 19

13. Warranty 19

5

EN

Operation manual Evolution Pro 2

IMPORTANT – Read the instructions carefully before use and keep

for future reference in the storage compartment at the foot end of

the carrier. So you always have it at hand whenever you need it.

1. Description of components

A – e child restraint system Evolution Pro 2

B – Carry handle

C – Release button stroller

D – Shoulder belt

E – Seat cover

F – Central adjuster

G – Buckle

H – Infant carrier release handle

I – Locking bar

J – Sunshade

K – Newborn inlay

L – Latch

M – Carry handle button

N – Lap belt guide

O – Front cover

P – Height adjustment handle

EN

6

2. Introduction

We are pleased that you have chosen the Evolution Pro 2 to be your

child restraint system.

e Evolution Pro 2 forms part of the Pro product line of our com

-

pany, which provides extensive safety for the protection of your

baby and growing child by making use of special energy-absorb

-

ing materials. e forces generated during a collision are absorbed

particularly well before they reach the delicate body parts of your

baby. To gain the most comprehensive protection for your child, the

Evolution Pro 2 must be used exactly as described in this manual!

e Evolution Pro 2 also stands out due to its adjustable reclined

position, which oers your child an almost at reclined position when

using the infant carrier on your stroller or as a rocker.

3. Suitability

e Evolution Pro 2 infant carrier has been tested and approved in ac-

cordance with the latest version of the Safety Standard ECE-R44/04.

It was granted the design approval for the “universal” and “semi-uni

-

versal” (in connection with the Isox platform) class of products.

is means:

“Universal”: e Evolution Pro 2 can be used in all vehicles with seats

with 3-point belt compliant with ECE-R16 or comparable standards.

“Semi-universal”: In connection with the Isox platform (accessory),

the Evolution Pro 2 may be used in all vehicles that are listed in the

vehicle type list. Check the latest version of the type list at:

www.kiddy.de/typelist_isoxbase.

7

EN

It is important to take note that you may never use the

Evolution Pro 2 on a car seat with an active front airbag!

A front airbag that hits the infant carrier with force can

cause serious injury or even death to the child!

For use in your vehicle, please also follow the manufactur-

er’s recommendations in your owner’s manual.

4. General safety instructions

WARNING

1. Please read the instructions for use carefully be-

fore using the car seat for the rst time. Incorrect

use can endanger the life of your child.

2. Many injuries are caused by mere thoughtless-

ness and can easily be avoided.

3. Never use the Evolution Pro 2 in the reclined po-

sition in a vehicle. e reclined position is intended

for use outside the vehicle only.

4. It is not permitted to make any modications

to the child restraint system. Doing so nullies or

impairs its eectiveness in protection. If diculties

arise, please consult your retailer or the manufac-

turer.

EN

8

5. Regularly inspect the dierent elements of the in-

fant carrier. e belt system and buckle in particular

must be checked regularly for wear and tear or pos-

sible damage.

6. Do not attempt to make adjustments while trav-

elling!

7. Always install the Evolution Pro 2 facing the direc-

tion opposite to the one in which you are travelling

(the child’s back facing the direction you are travel-

ling in).

8. Please adhere to the instructions in the owner’s

manual of the vehicle into which the Evolution Pro 2

is installed.

9. Make sure that all movable parts of the

Evolution Pro 2 are always properly locked in place

and that no parts are lodged between movable

seats or doors.

10. e infant carrier should only be used for the

age group 0+ (up to a maximum of 13 kg or approx.

15 months).

11. In vans and mini-vans it is particularly important

to ensure that the Evolution Pro 2 is installed in an

9

EN

easily accessible seat in the event that third-party

rescue is required.

12. Never use the Evolution Pro 2 as a shopping

bag or as a means for transporting something.

13. Never leave your baby unsupervised, especially

not when the Evolution Pro 2 is placed on a high

surface (nappy changing station, table etc.).

14. Always secure the baby with the belt system

(even when you are not using the Evolution Pro 2

inside the vehicle)!

15. Do not place any heavy items on the rear win-

dow shelf, these can become dangerous projectiles

in the event of an accident.

16. Always fasten the Evolution Pro 2 seat with the

vehicle seat belt or on the Isox platform when

transporting it in your car unoccupied.

17. Never use the Evolution Pro 2 seat without its

original cover, it forms part of the safety concept!

18. Shield the Evolution Pro 2 seat from direct sun-

light to prevent uncomfortable heating of the sur-

face.

EN

10

19. Schedule breaks during longer trips and take

your baby out of the Evolution Pro 2 seat to relieve

the pressure on its spinal column.

20. Only fasten the Evolution Pro 2 seat with the

vehicle’s own 3-point belt through the marked belt

guides or on the Isox platform available as an

accessory.

21. Do not use the Evolution Pro 2 any more if parts

have been damaged or after an accident (at an im-

pact speed greater than 10 km/h)! (See point 15.)

5. General use / Adjustments

5.1 Functions of the carry handle / Adjusting the reclined position

To adjust the carry handle, press both carry handle buttons (g. 1,

no. 1) and then swivel the carry handle (g. 1, no. 2) into the required

position.

WARNING

Make sure that both carry handle buttons are

locked in place again (they protrude)!

e carry handle of the Evolution Pro 2 can be used in two positions

(g. 2):

 g. 2, no. 1: Carry position / installation position in vehicle with

3-point belt or on Isox platform.

 g. 2, no. 2: Reclined position for use on stroller or as rocker.

11

EN

Never use the Evolution Pro 2 in the reclined position in a vehicle. e

reclined position is intended for use outside the vehicle only.

5.2 Using the newborn inlay

e Evolution Pro 2 is equipped with a comfort inlay for newborns.

is inlay ensures a more level position of your baby in the infant car

-

rier. is comfort inlay may only be used for babies up to the age of

6 months (g. 3). To remove the inlay, open the buckle and remove

the inlay from the shoulder belts.

Premature babies: A special inlay for premature babies, which oers

a signicantly better seating and reclined position, is available as an

accessory.

5.3 Using the sunshade

To extend the sunshade pull the hood towards the foot end of the

car seat. To retract the sunshade, push towards the head end of the

car seat.

6. Buckling / Unbuckling of the baby

6.1 Loosening the belt system

Turn the carry handle in to the carry position. Before you can adjust

the height of the shoulder belts, the belt system must be loosened.

For this purpose, keep the central adjuster pressed in the front un

-

der the seating area (g. 4, no. 1), and pull the shoulder belts (g. 4,

no. 2) out.

6.2 Adjusting the height of the belt system

Open the front cover at the head end of the infant carrier by slightly

pressing the hooks upward (g. 5, no. 1), now the cover opens (g. 5,

no. 2). Now turn the height adjuster handle 90° clockwise (g. 6, no. 1)

and pull the handle outward (g. 6, no. 2), then move it into the desired

EN

12

position upward or downward (g. 6, no. 3). e shoulder belts have

to be adjusted so that they are at the baby’s shoulder height (g. 7).

Lock the handles back into place after you have nished. Please make

sure that the belt system is not twisted or does not become lodged!

Close the front cover.

6.3 Buckling / Unbuckling of the baby

Always buckle up your child when it is in the infant carrier! Loosen the

shoulder belts as described in point 6.1 and place them over the side

of the rim of the carrier.

Place your baby in the infant carrier and then position the shoul

-

der belts over its shoulders (g. 8, no. 1). Place the safety belt lock

tongues attached to the shoulder belts over each other (g. 8, no. 2).

Now push the safety belt lock tongues into the buckle. It is locked in

place when a click sound is heard (g. 9). Make certain that it is se

-

curely locked in place! Now pull the central belt until the belt system

ts the body of the child snugly (g. 10)!

Make sure that the space between the belts and your child is no more

than the width of a nger (approx. 1 cm) and that the belt system is

not twisted.

Loosen the shoulder belts as described in point 6.1 and press the red

button on the buckle to unbuckle your baby. Now you can take the

child out of the seat.

13

EN

7. Use in the vehicle

7.1 In-vehicle installation with seat belt

7.1.1 Seat selection

Read up all the necessary information about the use of

child restraint systems in your vehicle owner’s manual.

e Evolution Pro 2 child restraint system can be installed on any seat

of vehicles equipped with a 3-point belt system (g. 11).

If you want to install the child restraint system in the pas-

senger seat, the airbag must be deactivated or you will

have to use a dierent seat.

7.1.2 Installation steps with the seat belt

WARNING

1. Place the Evolution Pro 2 facing the rear and with

the handle in the carry position on a seat without an

active front airbag and with a 3-point belt (g. 12).

2. Before starting the journey, please always make

sure that the harness is put on and tightened cor-

rectly.

Pull the vehicle seat belt out and feed the lap belt through both lap

belt guides and press the safety belt lock tongue into the buckle

(g. 13) with a clearly audible click. Check that everything is locked

into place. Tighten the lap belt (g. 13). Now place the shoulder belt

around the infant carrier and feed it through behind the front cover

EN

14

of the infant carrier (g. 14). Make certain that the belt clip is in the

correct position. Now tighten the belt system (g. 15). Make sure that

the belt is not twisted (g. 15)!

e infant carrier is in the optimum position when the rear line at the

shell is at a 90° angle (vertical) to the horizontal line (g. 15).

Some vehicles are tted with so-called retractor locks.

With this, the automatic recoiling of the belt can be blocked,

which makes a more solid installation of the Evolution Pro 2

possible. Read your vehicles’ owner manual for more infor

-

mation on this feature or ask your authorised workshop.

7.2 Installation with the Isox platform

7.2.1 Seat selection

Read up all the necessary information about the use of

child restraint systems in your vehicle owner’s manual.

With the Isox platform, the child restraint system Evolution Pro 2

can be installed in any seat in a vehicle that is tted with Isox an-

chors.

However, you must refer to the included vehicle type list with regard

to seat selection in your vehicle. e latest version of the vehicle type

list is always available for download at:

www.kiddy.de/typelist_isoxbase.

Rear-facing child restraint systems may never be used

with an activated front airbag!

Traces of use or discolouration can appear on some vehicle seat cov

-

ers made from sensitive materials (e.g. velour, leather etc.) if car seats

or platforms are used. To avoid this we recommend to place a seat

cover shield or protection mat underneath the product.

La page charge ...

kiddy EVOLUTION PRO 2 Manuel utilisateur

kiddy EVOLUTION PRO 2 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents