Alfresco ALXE Grill Manuel utilisateur

Marque: Alfresco

Modèle: ALXE Grill

Catégorie: Barbecues

Taper: Manuel utilisateur

Ce manuel convient également à

F WARNING

ELECTRICAL PARTS AND COMPONENTS

DISCONNECT ALL POWER SUPPLIES AND BATTER-

IES BEFORE SERVICING.

H WARNING

FLAMMABLE GAS

DISCONNECT ALL PROPANE OR NATURAL GAS

SUPPLIES TO THIS UNIT BEFORE SERVICING.

ALFRESCO™ Gourmet Grills

A division of Superior Equipment Solutions, Inc.

1085 Bixby Drive

City of Industry, CA. 91745

Ph.: (888) 383-8800

Fax: (323) 726-4700

Web: www.alfrescogrills.com

! WARNING

1. DO NOT STORE OR USE GASOLINE OR OTHER

FLAMMABLE LIQUIDS OR VAPORS IN THE VI-

CINITY OF THIS OR ANY OTHER APPLIANCE.

2. AN LP CYLINDER NOT CONNECTED FOR USE

SHALL NOT BE STORED IN THE VICINITY OF

THIS OR ANY OTHER APPLIANCE.

! DANGER

IF YOU SMELL GAS:

1. SHUT OFF GAS TO THE APPLIANCE

2. EXTINGUISH ANY OPEN FLAME.

3. OPEN LID.

4. IF ODOR CONTINUES, KEEP AWAY FROM THE

APPLIANCE AND IMMEDIATELY CALL YOUR

GAS SUPPLIER AND OR FIRE DEPARTMENT.

! AVERTISSEMENT

1. NE PAS ENTREPOSER NI UTILISER DE L’ESSENCE

NI D’AUTRES VAPEURS OU LIQUIDES INFLAMMA-

BLES DANS LE VOISINAGE DE L’APPAREIL, NI DE

TOUT AUTRE APPAREIL.

2. UNE BOUTEILLE DE PROPANE QUI N’EST PAS RAC-

CORDÉE EN VUE DE SON UTILISATION. NE DOIT

PAS ÉTRE ENTREPOSÉE DANS LE VOISINAGE DE

CET APPAREIL OU DE TOUT AUTRE APPAREIL.

! DANGER

S’IL Y A UNE ODEUR DE GAZ:

1. COUPEZ L’ADMISSION DE GAZ DE ‘LAPPARIEL.

2. ÉITENDRE TOUTE FLAME NUE.

3. OUVRIR LE COURVERCLE.

SI L’ODEUR PERSISTE, ÉLOIGNEZ-VOUS DE L’APPA-

REIL ET APPELEZ IMMÉDIATEMENT LE FOURNIS-

SEUR DE GAZ OU LE SERVICE D’INCENDIE.

GENERAL SAFETY PRECAUTIONS:

WARNING:

 If the information in this manual is not followed exactly, a fire or explosion may result causing

property damage, personal injury or death.

 Do not try lighting this appliance without reading the LIGHTING INSTRUCTIONS section of this

manual. For outdoor use only.

 This cooking appliance is not intended to be installed in or on recreational vehicles and / or boats.

BEFORE USING THE GRILL:

 Ensure that the grill has been leak tested. (see page 11)

 Remove any packing material.

 Read and understand the instructions in this manual.

 Electric power supply must be plugged-in at all times for barbecue operation; except during any

electrical maintenance.

3020914

CALIFORNIA PROPOSITION 65 - WARNING

The burning of gas cooking fuel generates toxic by-products, which are on the list of substances which

are known by the State of California to cause cancer or reproductive harm. California law requires

businesses to warn customers of potential exposure to such substances. To minimize exposure to

these substances, always operate this unit according to the use and care manual, ensuring you

provide good ventilation when cooking with gas. This warning is issued pursuant to California Health &

Safety Code Sec. 25249.6

BARBEQUE SERIAL NUMBER LABEL

TESTED IN ACCORDANCE WITH:

ANSI Z21.58-2018 / CSA 1.6-2018

The Standard for Outdoor Cooking Gas Appliances.

Installation of this cooking appliance must be made in accordace with local codes. In the absence of

local codes, this unit should be installed in accordance with the National Fuel Gas Code No. Z223.1/

NFPA 54, Natural Gas and Propane Installation code CSA B149-1 , or Propane Storage and Handling

Code B149.2. All Electrical Components must be electrically grounded in accordance with local codes

or in the absence of local codes with the National Electrical Code ANSI/NFPA 70 or Canadian Electrical

code CSA C22.1

F AVERTISSEMENT

PIÈCES ÉLECTRIQUES ET COMPOSANTS.

DÉBRANCHER TOUS LES BLOCS D'ALIMENTA-

TION ET LES PILES AVANT DE LES RÉPARER.

H AVERTISSEMENT

GAZ INFLAMMABLE

DÉBRANCHER TOUS LES GAZ PROPANE OU

GAZ NATUREL DE CET APPAREIL AVANT DE

PROCÉDER À L'ENTRETIEN.

READ THIS CARE AND USE MANUAL CAREFULLY AND COMPLETELY BEFORE USING YOUR

GRILL TO REDUCE THE RISK OF FIRE, BURN HAZARD OR OTHER INJURY. KEEP THIS MANU-

AL FOR FUTURE REFERENCE.

When properly cared for, your ™ Gourmet Grill will give safe, reliable service for many years.

However, extreme care must be used since the grill produces intense heat, which can increase accident

potential. When using this appliance, basic safety practices must be followed, including but not limited to

the following:

 Begin by ensuring proper assembly. A qualified technician should perform all other service.

 Do not repair or replace any part of the grill unless specifically recommended in this manual.

 All other service should be referred to and performed by a qualified technician.

 For personal safety, wear proper apparel while barbecuing.

 Loose fitting garments or sleeves should never be worn while using this appliance.

 Some synthetic fabrics are highly flammable and should not be worn while cooking.

 Never let clothing, pot holders or other flammable materials come in contact with or too close to any grate,

burner or hot surface until it has cooled down sufficiently. Fabrics may ignite and result in personal injury.

 Use only dry potholders: moist or damp potholders on hot surfaces may cause personal burns from steam. Do

not use a towel or bulky cloth in place of potholders. Do not let potholders touch hot portions of the grill rack.

 Only certain types of glass, heatproof glass ceramic, earthenware, or other glazed utensils are suitable for grill

use. These types of materials may break with sudden temperature changes. Use only on low or medium heat

settings and according to their manufacturer’s directions.

 Grease is flammable. Let hot grease cool before attempting to handle it.

 Avoid letting grease deposits collect in the bottom of the grill by cleaning the grease tray often. Never while

grill is on or hot from recent use; pan will not come out.

 Do not use aluminum foil to line the grill racks, nor to line the drip tray. This can severely upset combustion

airflow or trap excessive heat in the control area. The result of this can be melted knobs, igniters and in-

creased chance of personal injury. Never grill without the drip pan in place and pushed all the way to the back

of the grill. Without the drip pan, hot grease can leak downward creating a fire or explosion hazard.

 Children should not be left alone or unattended in an area where the grill is being used. Never allow them to

sit, stand or play on or around the grill. Do not store items of interest to children around or below the grill or in

the cart. Never allow children to crawl inside of the cart.

 Do not heat unopened food containers that may cause the container to build-up pressure and burst.

 Protect your hand when opening a hot grill lid. Never lean over an open hot grill.

 When lighting a burner, always pay close attention to what you are doing. Be certain you are depressing the

correct igniter button labeled for the burner you intend on using.

 When using the grill: do not touch the grill rack, burner grate, hood or immediate surrounding area as these

areas become extremely hot and could cause burns. Use only the handles and knobs provided for operation of

the grill.

 For proper lighting and performance of the burners keep the ports clean. It is necessary to clean them periodi-

cally for Optimum performance. The burners will only operate in one position and must mounted correctly for

safe operation.

 Clean the grill with caution. Avoid steam burns; do not use a wet sponge or cloth to clean the grill while it is

hot. Some cleaners produce noxious fumes or can ignite when applied to a hot surface.

 INSECT WARNING: Spiders and insects can nest in the burners of this and other grills, and cause the gas to

flow from the front of the burner. This is a very dangerous condition, which can cause a fire to occur behind

the valve panel, thereby damaging the grill and making it unsafe to operate. Inspect the grill at least twice a

year.

 Be sure all grill controls are turned off and the grill is cool before using any type of aerosol cleaner on or

around the grill. The chemical that produces the spraying action could, in the presence of heat, ignite or cause

metal parts to corrode.

 Do not use this appliance under overhead combustible surfaces. Use only in well ventilated areas. Do

not use in buildings, garages, sheds, breezeways or any enclosed areas.

 Keep the area surrounding the grill free from combustible materials, trash, or combustible fluids and vapors

such as gasoline or charcoal lighter fluid. Do not obstruct the flow of combustion gases and ventilation air-

ways.

 Keep the back of the cart free and clear from debris.

 If the unit is stored indoors ensure that it is cool. If propane is used, the cylinder must be unhooked and the

propane cylinder stored outside in a well-ventilated area, out of reach of children.

 Never use the grill in windy conditions. If located in a consistently windy area, oceanfront, mountaintop, etc... a

windbreak will be required. Always adhere to the specified clearances.

 Keep any electrical supply cord, away from the heated areas of the grill.

! WARNING

FOR OUTDOOR USE ONLY

NOT TO BE INSTALLED IN OR

ON RECREATIONAL VEHICLES

AND / OR BOATS.

! WARNING

NEVER USE A DENTED OR

RUSTED LIQUID PROPANE

TANK. SHUT OFF TANK WHEN

NOT IN USE.

! AVERTISSEMENT

POUR UTILISATION À

L'EXTÉRIEUR

NE PAS ÊTRE INSTALLÉ DANS OU

SUR DES VÉHICULES RÉCRÉATIFS

ET / OU DES BATEAUX.

! AVERTISSEMENT

N'UTILISEZ JAMAIS DE RÉSERVOIR

DE PROPANE LIQUIDE BOSSELÉ

OU ROUILLÉ. ÉTEINDRE LE RESER-

VOIR LORSQU'IL N'EST PAS UTILI-

SÉ.

LOCATING AND ASSEMBLING THE GRILL:

When determining a suitable location for your grill, take into account concerns such as exposure to wind,

rain, sprinklers, proximity to traffic paths and keeping any gas supply line runs as short as possible.

Locate the grill only in a well-ventilated area. Never locate the grill in a building, garage, breezeway,

shed or other such enclosed areas without an approved ventilation system. Never locate the grill over,

under or next to unprotected combustible construction. During heavy use, the grill will produce a lot of

smoke.

CLEARANCES:

TO NON-COMBUSTIBLE CONSTRUCTIONS:

A minimum of 3-5/8” clearance from the back of the grill to non-combustible construction is required to

allow the hood to be opened fully.

TO COMBUSTIBLE CONSTRUCTIONS:

This appliance should NOT be located over, under or next to unprotected combustible construction. If

your enclosure is combustible, then an INSULATED JACKET manufactured by ™ Gourmet

Grills, is required.

ASSEMBLY:

BUILT-IN MODELS:

Before locating your ™ Gourmet Grill into your Non-combustible enclosure, complete the

following steps:

1. Remove all packaging materials.

2. Ensure that the burners are positioned correctly on their orifices, and are fully seated onto

their supports.

3. Position the briquette trays onto their support ledge.

4. Make the connection to the gas regulator according to the instructions on pages 8 through

11 for your gas type.

5. To comply with safety and service requirements, main gas shut off valve must be

accessible from front of grill without using any tools.

CODE REQUIREMENTS:

When installing a grill or other gas appliance into an enclosure (island), the enclosure must be

constructed with ventilation at both the top and bottom to avoid accumulation of gas should there be a

leak.

Installation of this cooking appliance must be made in accordace with local codes. In the absence of

local codes, this unit should be installed in accordance with the National Fuel Gas Code No. Z223.1/

NFPA 54, Natural Gas and Propane Installation code CSA B149-1 , or Propane Storage and Handling

Code B149.2.

All Electrical Components must be electrically grounded in accordance with local codes or in the

absence of local codes with the National Electrical Code ANSI/NFPA 70 or Canadian Electrical code

CSA C22.1

Your ™ Gourmet Grill has provision for mounting onto a mobile cart if you choose to do so.

Contact your

™ dealer for the appropriate cart for your grill.

FREE STANDING MODELS:

Complete the following steps:

1. Remove all packaging materials.

2. Ensure that the burners are positioned correctly on their orifices, and are fully seated onto

their supports.

3. Position the briquette trays onto their support ledge.

4. Make the connection to the gas regulator according to the instructions on pages 8 through

11 for your gas type.

5. Allow a minimum of 3” clearance around all sides of grill cart for proper air movement.

6. Lock the rear casters to prevent unwanted grill movement.

WARNING:

To prevent harm and ensure proper operation of your grill, it is imperative that the burners are properly

installed with respect to the gas orifices. Be certain that the orifice is inserted completely into the

burner’s inlet and that the burner rests firmly on its support bracket.

The burner should not rock side-to-side nor top-to-bottom if properly installed. If excessive burner

movement is present, reseat burner or contact your authorized service provider.

NOTES CONCERNING GFCI USE AND LOCATION:

1. Do not attempt to circumvent using a GFCI receptacle, it is for your safety.

2. Ensure that the GFCI receptacle is located in an easily accessed location.

3. Follow the manufacturer’s instructions for installation and testing (must comply with local and

national codes).

! WARNING

IMPORTANT ELECTRICAL INSTRUCTIONS:

THE GRILL’S ROTISSERIE MOTOR AND LIGHTS ARE WIRED TO A SINGLE

THREE-PRONG (GROUNDING) PLUG FOR YOUR PROTECTION AGAINST SHOCK

HAZARD. THE GRILL SHOULD BE PLUGGED DIRECTLY INTO A PROPERLY

GROUNDED GFCI THREE-PRONG RECEPTACLE.

! AVERTISSEMENT

INSTRUCTIONS ÉLECTRIQUES IMPORTANTES:

LE MOTEUR ROTISSERIE DE GRILL ET LES LUMIÈRES SONT CÂBLÉES À UNE FICHE UNIQUE À

TROIS PRONG POUR TU PROTECTION CONTRE LE DÉCHARGEMENT DES CHOCS. LE GRILLE

DEVRAIT ÊTRE PLUGÉ DIRECTEMENT DANS UN RECEPTACLE GFCI TRES PRONG COR-

RECTEMENT TERRESTRE.

NE PAS COUPER OU RETIRER LE TERRAIN PRONG FROTH CETTE FICHE. GARDEZ LE CORDON

ÉLEVÉ À PARTIR DE SURFACES DE GRILLE CHAUFFÉES. RETIRER LE MOTEUR QUAND IL

N'EST PAS UTILISÉ

BRIQUETTE TRAY INSTALLATION:

GAS CONNECTIONS:

NEVER CONNECT THE GRILL TO AN UNREGULATED GAS SUPPLY.

Total gas consumption (BTUH) with all

burners set on “HI” is a follows:

LIQUID PROPANE (LP):

Before proceeding, ensure the unit is fitted for LP gas. Connecting to an improper gas type will result in

poor performance and increased risk of damage or injury.

Installation of this cooking appliance must be made in accordace with local codes. In the absence of

local codes, this unit should be installed in accordance with the National Fuel Gas Code No. Z223.1/

NFPA 54, Natural Gas and Propane Installation code CSA B149-1 , or Propane Storage and Handling

Code B149.2.

Manifold pressure with LP Operating: 10.0” W.C. Non-operating: 11.2” W.C.

L.P. TANK REQUIREMENTS:

Use only a standard 20 Lb. (5 Gal.) propane gas cylinder (18-1/4” H x 12-1/4” Ø). The tank must be in-

stalled in the upright position. Do not use a dented or rusty LP tank as it may be hazardous and should

be checked by your LP supplier. Never use a cylinder with a damaged valve.

The LP gas cylinder must be constructed and marked in accordance with the specifications for LP gas

cylinders of the U.S. Department of Transportation (DOT). The cylinder must be provided with a shut off

valve terminating in an LP gas supply cylinder valve outlet specified, as applicable, for connection type

QCC1 in the standard for compressed gas cylinder valve outlet and inlet connections ANSI/CGA-V-I.

Remove top grills.

Briquette trays located over the

gas burners

MODEL: LP GAS NG GAS

ALXE-30SZ 63,100 64,200

ALXE-36SZ 82,000 85,800

ALXE-42SZ 84,200 88,200

ALXE-56SZ 122,000 124,000

ALXE-56BFG 116,900 122,900

LP GAS CONNECTION TO LP TANKS:

Your ™ Gourmet Grill for use with LP gas comes equipped with its own regulator, which

MUST NOT be removed. There is also a secondary high capacity, hose/regulator assembly for connec-

tion to a standard 20 Lb. LP cylinder. The LP gas pressure regulator and hose supplied with this unit

must be used without alteration.

If this assembly needs to be replaced use only the type specified by ™ Gourmet Grill for this

appliance. 30” grills require at minimum, a 90,000 BTUH regulator / hose assembly. All other sizes re-

quire at minimum, a 160,000 BTUH two-stage regulator / hose assembly.

To connect the regulator / hose assembly follow the next steps:

1. Locate the regulator and gas connection point in the rear right side of your BBQ unit (remove

the rear panel from the BBQ cart to gain access - in cart mounted models).

2. Attach a 1/2” FPT x 1/2” MPT (male-to-female) elbow to the regulator (see figure # 2).

3. Fasten the hose connection to a 1/2” MPT x 3/8” COMP (compression flare fitting) connected

to the elbow. (see figure # 2).

1/2” FPT X 3/8” FLARE

BRASS FITTING

CONVERTIBLE GAS PRESSURE

REGULATOR

TYPICAL ™ ALXE

Figure # 2

TYPICAL LP

GAS TANK

LP REGULATOR AND HOSE

ASSEMBLY (PRESET TO 10” WC)

1/2” FPT X 1/2” MPT

90° ELBOW

! WARNING

KEEP ANY ELECTRICAL CORD

AND FUEL SUPPLY HOSE AWAY

FROM ANY HEATED SURFACES.

! AVERTISSEMENT

GARDER TOUT LE CORDON ÉLECTRIQUE ET LE

TUYAU D'ALIMENTATION DE CARBURANT À

L'ÉGARD DE TOUTES SURFACES CHAUF-

FANTES.

GAS CONNECTION - NATURAL GAS (NG)

NEVER CONNECT THE GRILL TO AN UNREGULATED GAS SUPPLY.

Before proceeding, ensure the unit is fitted for natural gas. Connecting to an improper gas type will result

in poor performance and increased risk of damage or injury. Installation of this cooking appliance must

be made in accordace with local codes. In the absence of local codes, this unit should be installed in

accordance with the National Fuel Gas Code No. Z223.1/ NFPA 54, Natural Gas and Propane

Installation code CSA B149-1 , or Propane Storage and Handling Code B149.2.

Manifold pressure with NG: Operating: 4.0” W.C. (.14 PSI)

Non-operating: 4.5” W.C. (.16 PSI)

Optimum pressure: 7.0” W.C. (.25 PSI)

LP GAS CONNECTION TO LP PIPED SYSTEMS:

An LP piped system is one with a large central LP tank that feeds the entire household. Those systems

are normally equipped with a high pressure regulator by the large LP tank and low pressure regulators

close to the home.

The gas line connectors must comply with the Standard for Connectors for Outdoor Gas Appliances

and Manufactured Homes, ANSI Z21.75 • CAS 6.27, and suitable for outside installation. The maxi-

mum length of the connection shal be 6 Ft. (1.82 m)

! CAUTION

CYLINDERS MUST BE STORED OUTDOORS IN A

WELL VENTILATED AREA OUT OF THE REACH OF

CHILDREN.

DISCONNECTED LP CYLINDERS MUST HAVE THREADED

VALVE PLUGS TIGHTLY INSTALLED, AND MUST NOT BE

STORED IN A BUILDING, GARAGE OR ANY OTHER ENCLOSED

AREA. THE GAS MUST BE TURNED OFF AT THE SUPPLY CYL-

INDER WHEN THE UNIT IS NOT IN USE. IF THE APPLIANCE IS

STORED INDOORS, THE CYLINDER MUST BE DISCONNECTED

AND REMOVED FROM THE APPLIANCE.

! WARNING

YOUR ALFRESCO™ GOURMET GRILL’S

PRESSURE REGULATOR HAS A MAXI-

MUM INPUT PRESSURE OF 14” WC. (OR

APPROX. .5 PSI) , AND A SAFETY LIMIT

OF 69” WC. (2.5 PSI).

! REGULATOR NOTICE

Exposure to pressures above the safety

limit of 69” WC. will permanently damage

the gas regulator requiring a replacement.

OVER PRESSURE DAMAGE IS NOT COV-

ERED BY YOUR ALFRESCO WARRANTY

! MISE EN GARDE

LE CYLINDRE DOIT ÊTRE STOCKÉ À L'EXTÉRIEUR

DANS UN ENDROIT BIEN VENTILÉ ET HORS DE LA POR-

TÉE DES ENFANTS.

DÉBRANCHER LES BOUTEILLES DE LP DOIVENT AVOIR DES

BOUCHONS DE VALEUR VISSÉS HERMÉTIQUEMENT INSTAL-

LÉS, ET NE DOIVENT PAS ÊTRE STOCKÉS DANS UN BÂTI-

MENT, GARAGE OU TOUT AUTRE ESPACE FERMÉ. LE GAZ

DOIT ÊTRE ARRÊTÉ AU NIVEAU DU CYLINDRE D'ALIMENTA-

TION LORSQUE L'APPAREIL N'EST PAS UTILISÉ. SI L'APPA-

REIL EST ENTREPOSÉ À L'INTÉRIEUR, LE CYLINDRE DOIT

ÊTRE DÉBRANCHÉ ET RETIRÉ DE L'APPAREIL.

! AVERTISSEMENT

VOTRE RÉGULATEUR DE PRESSION AL-

FRESCO GOURMET GRILLADES A UNE

PRESSION D'ENTRÉE MAXIMALE DE 14"

WC (OU ENVIRON 0,5 PSI), ET UNE LIM-

ITE DE SÉCURITÉ DE 69" WC (2,5 PSI).

1/2” FPT X 1/2” MPT

90° ELBOW

CONVERTIBLE GAS PRESSURE

REGULATOR

TYPICAL ™ ALXE

BBQ (36” MODEL SHOWN)

SHUT OFF HAND VALVE

MUST BE LOCATED IN

ACCESSIBLE AREA

INCOMING NG

GAS SUPPLY

Figure # 3

NG FLEXIBLE

HOSE

NOTE: To ensure proper heating performance of this appliance, verify that the gas line supply pressure

is adequate (7.0” W.C. supply pressure is preferred) to maintain 4.5” W.C. manifold pressure.

Use a minimum 1/2” ID flex hose to prevent gas starvation.

NATURAL GAS CONNECTION:

Ensure that the service pipe supplying the Grill is fitted with a shut off valve conveniently positioned and

easily accessible as an emergency gas shutoff.

Your ™ Gourmet Grill for use with natural gas comes equipped with its own regulator which

MUST NOT be removed.

If this regulator needs to be replaced use only the type specified by ™ Gourmet Grill for this

appliance.

To connect the regulator / hose assembly follow the next steps:

1. Locate the regulator and gas connection point in the rear right side of your BBQ unit (remove the

rear panel from the BBQ cart to gain access - in cart mounted models).

2. Attach a 1/2” FPT x 1/2” MPT (male-to-female) elbow to the regulator (see figure # 3).

3. Fasten the hose connection to a 1/2” MPT x 3/8” COMP (compression flare fitting) connected to

the elbow. (see figure # 3).

Connect flare fitting to gas supply using a 1/2” Ø minimum flexible (semi–rigid) stainless steel gas hose,

no more than 48” in length. The hose as well as the connectors must comply with the Standard for Con-

nectors for Outdoor Gas Appliances and Manufactured Homes, ANSI Z21.75 • CAS 6.27.

LEAK TESTING:

GENERAL:

Although all gas connections on your ™ Gourmet Grill are leak tested at the factory prior to

shipment, a complete gas tightness check must be performed at the installation site due to possible

mishandling in shipment, or excessive pressure unknowingly being applied to the unit. Periodically check

the whole system for leaks, or immediately check if the smell of gas is detected.

BEFORE TESTING:

 Do not smoke while leak testing.

 Never leak test with an open flame.

 Make a soap solution of one part liquid detergent and one part water for leak testing purposes.

 Apply the solution to the gas fittings by using a spray bottle, or brush.

 For LP units, always check with a full cylinder.

TO TEST:

 Make sure all control valves are in the “OFF” position.

 Apply the soap solution described above to all fittings.

 Turn the gas supply on.

 Check all connections from the supply line, or LP cylinder up to and including the manifold pipe

assembly.

 Soap bubbles will appear where a leak is present.

 If a leak is present, immediately turn off gas supply, tighten any leaking fittings, turn the gas

supply back on, and recheck.

 If you cannot stop a gas leak turn off the gas supply and call your dealer where you purchased

your grill.

 Do not use the grill until all connections have been checked and do not leak.

IMPORTANT NOTE:

ALWAYS CHECK FOR LEAKS AFTER EVERY LP TANK CHANGE.

If a leak is present, or if the connection hose shows signs of wear, these conditions must be corrected

prior to using your grill. If it is evident there is excessive abrasion or wear,or the hose is cut, it must be

replaced prior to the cooking appliance is being put into operation.

The replacement hose assembly is part number:

PROP-KIT-01 which consists of a 36” long hose assembly

with dual in-line regulator and a 3/8” ODF connector.

Contact

™ Grills for replacement.

Check all gas supply fittings for leaks before each use. It is handy to keep a spray bottle of soapy water

near the shut-off valve of the gas supply line. Spray all the fittings. Bubbles indicate leaks.

LIGHTING INSTRUCTIONS:

BEFORE LIGHTING…

The pressure regulator and hose assembly supplied with the unit must be used. Never substitute

regulators for those supplied with the grill. If a replacement is necessary, contact the factory for proper

replacement.

Screw the regulator (Type QCC1) onto the LP tank. Leak check the hose and regulator connections with

a soap and water solution before operating as explained on the LEAK TESTING section of this manual.

BUTTON SYMBOLS AND LOCATIONS:

To ensure that an IR burner is lit, very carefully place your hand 8-10 inches away from the burner

surface. If you do not feel the heat of the burner, shut off the gas at the control knob, wait five minutes,

and then try again.

LIGHTING THE GRILL’S U-BURNER , SMOKER AND SEAR-ZONE™ BURNERS:

Turn all knobs to “OFF” and then turn on the gas supply.

Adjustable valves are labeled OFF MAX ► MIN. Non adjustable valves are labeled OFF ON.

Always keep your face and body as far away from the grill as possible when lighting!.

Lift the hood, depress the igniter button (see above symbol) and for the burner you are trying to light,

immediately push and turn the burner control knob 90° counter-clockwise to:

 “MAX” position (U-Burners and Smoker ) or

 “ON” position (Sear-Zone™).

Wait for the burner to light. Adjust the temperature by

turning the knob from MAX (high setting) to MIN (low

setting) by turning counter clock-wise.

NOTE: The first burner may take longer to light while air is

purged from the gas supply system. If the burner does not

light within 4 seconds, turn knobs to “OFF” and wait 5

minutes to allow any accumulated gas to dissipate before

trying again.

LIGHTING SIDE BURNERS (MODELS ALXE-56 & 56 SZ):

FRONT BURNER: Push and turn the side burner right hand control knob 90° counter-clockwise to the

“MAX” position and immediately depress the right hand igniter button. You’ll hear a snapping sound from

the spark which will be provided to both side burners. It is necessary to keep the igniter button

depressed until the burner is lit.

IGNITER BUTTON SWITCH

(on the TOP)

ROTISSERIE SWITCH

(at the BOTTOM)

LIGHT FIXTURES SWITCH

(in the MIDDLE)

! WARNING

HOOD MUST BE OPEN WHEN LIGHTING

THE GRILL.

HOOD SHOULD NOT BE CLOSED FOR LONG

PERIODS WHEN IR BURNERS ARE IN USE.

! WARNING

DO NOT ATTEMPT TO LIGHT THE

GRILL IF THE ODOR OF GAS IS

PRESENT.

! AVERTISSEMENT

LE CAPOT DOIT ÊTRE OUVERT LORSQUE

L'ALLUMAGE DE LA HOTTE DU GRIL.

NE DOIT PAS ÊTRE FERMÉ PENDANT DE

LONGUES PÉRIODES LORSQUE DES BRÛ-

LEURS IR SONT UTILISÉS.

! AVERTISSEMENT

N'ESSAYEZ PAS D'ALLUMER LE

GRIL SI L'ODEUR DE GAZ EST PRÉ-

SENTE.

TURN 90° TO MAX

OR ON SETTING

ADJUST TEMP.

NOTCH INDICATOR

REAR BURNER: Repeat the same operation

as explained on the front burner but using the

side burner left hand control knob.

If either burner does not light within 4

seconds, turn knob to “OFF” and wait 5

minutes to allow any accumulated gas to

dissipate before trying again.

NOTE: To ensure proper spark ignition, do not change the gap between the electrode wires and the

burners. The optimum gap is preset at the factory between 1/8” and 3/16”.

ROTISSERIE BURNER LIGHTING:

Open the hood, press the proper igniter button (see previous

page) and then turn the control knob 90° counter-clockwise to

the “ON” position. If the burner does not light within 4 seconds,

turn the control knob to “OFF”, wait five minutes and attempt to

relight.

After your first use of the rotisserie burner it is likely that the

stainless steel adjacent and directly above the burner will

darken to a dark blue color. This is a normal property of the

corrosion resistant type 304 stainless steel used in

manufacturing the Grill and is not detrimental to its operation.

PREHEATING THE GRILL:

U-BURNERS:

Preheating the grill is important for best performance. To preheat the grill when cooking with the U-

burners, close the hood after lighting the burners as described above. Set the grill control knobs on

“MAX” for 15 minutes.

IR-BURNERS:

Preheating the IR burners is important to protect them from food drippings. After lighting the IR burners

as described above, allow to preheat on “ON” for four minutes before beginning to grill.

If your grill is equipped with a SEAR-ZONE™ IR BURNER, light and preheat the U-BURNERS first, then

light and preheat the SEAR-ZONE™ IR BURNER.

ROTISSERIE BURNER:

Light the rotisserie burner as described in the lighting instructions. Once lit, the rotisserie burner will

reach cooking temperatures in about 1 minute.

! CAUTION

IN SUNNY ENVIRONMENTS, THE

FLAME FROM AN IR BURNER

MAY BE IMPOSSIBLE TO SEE.

PUSH TO

IGNITE

PUSH & TURN TO “MAX”

! MISE EN GARDE

DANS LES ENVIRONNEMENTS SO-

LEILS, LA FLAMME D'UN BRÛLEUR

IR PEUT ÊTRE IMPOSSIBLE À VOIR.

BURNER ADJUSTMENTS:

NOTE: grills are available with both U-burners and IR burners. The following instructions

apply only to the U-burners. IR burners do not require adjustment and need only be checked visually for

proper performance. On high, an IR burner should glow red evenly over its entire surface.

U-BURNER AIR ADJUSTMENT:

Each grill burner is tested and adjusted at the factory prior to shipment; however, variations in the local

gas supply, elevation and other factors might make it necessary to adjust the burners. The flames of the

burners should be visually checked and compared with Figure 4.

If any of these conditions exist, check if dirt, debris, spider webs, etc., are blocking the air shutter or

burner ports. Proceed with air shutter adjustment.

AIR SHUTTER ADJUSTMENT:

A sheet metal cap at the inlet of the burner called the “AIR SHUTTER” regulates the amount of air that

enters into the burner for combustion.

The air shutter is locked in place by a screw, which must be loosened prior to lighting the burner for

adjustment. The air shutter adjustment screws are accessible with a screwdriver by removing the burner.

Loosen the screw of the air shutter. Reinstall the burner. Make certain that the burners are sitting

properly on the orifices taking care not to move or damage the igniter electrode.

Light the burners and adjust according to the following directions:

 Turn the valve on “HI”, light the burner and allow it to “WARM UP” for 10 minutes.

 If the flame is yellow, indicating insufficient air, turn the air shutter counter-clockwise to

allow more air to the burner. *Caution, see note below.

 If the flame is noisy and tends to lift away from the burner, (WITH THE BRIQUETTE

TRAYS IN POSITION) indicating too much air, turn the air shutter clockwise to reduce

the amount of air to the burner.

 Retighten the locking screw of the air shutter cap.

*NOTE: Be careful, as the burner may be or will become very hot after lighting it.

AIR SHUTTER APPERTURE IS FACTORY SET TO APPROXIMATELY 1/2”

FOR LP & 5/8” FOR NG - MINOR ADJUSTMENTS MAY BE NECESSARY DUE

TO FACTORS SUCH AS HIGH ALTITUDE LOCATIONS.

Figure # 5

Flames should be blue and stable with no yellow tips, excessive noise or lifting.

LOW HEAT SETTING ADJUSTMENT:

NOTE:

THE LOW HEAT SETTING ON YOUR GRILL IS PRESET AT THE FACTORY. ADJUST ONLY IF

ALTITUDE OR ENVIRONMENTAL FACTORS ARE CAUSING POOR, LOW HEAT, PERFORMANCE.

ADJUSTMENT STEPS:

1. Follow lighting instructions by setting the control

knob on “HI” and allow the burner to preheat for 10

minutes.

2. Turn the control knob to “LOW” and wait for the

burner temperature to drop and stabilize.

3. Attempting adjustment at any setting other than

LOW can create a dangerous condition.

4. Remove knob by pulling straight away from control

panel.

5. Insert a small blade screwdriver into the valve stem

to begin the adjustment. (see figure # 5)

6. Turn counter-clockwise to INCREASE the low heat

flame while using pliers to hold the stem securely.

7. Adjust the flames so the burner is fully lit around the perimeter when the knob is in the LOW

position. Once proper adjustment is reached, reattach the knob by pushing onto stem.

AIR SHUTTER

ADJUSTMENT CUP

SET-SCREW

U-BURNER

Figure # 4

1” MAXIMUM

” MAXIMUM

FLAME SIZE

! WARNING

NEVER ADJUST THE BURNER SO LOW

THAT IT MAY GO OUT DURING USE. DO

NOT OPERATE THE GRILL WITH THE LOW

HEAT SCREW REMOVED.

GAS CAN ESCAPE AND CAUSE A

POTENTIALLY HAZARDOUS CONDITION.

! AVERTISSEMENT

NE JAMAIS AJUSTER LE BRÛLEUR SI BAS QU'IL

PEUT S'ÉTEINDRE PENDANT L'UTILISATION.

N'UTILISEZ PAS LE GRIL AVEC LA VIS À

CHALEUR BASSE RETIRÉE.

LE GAZ PEUT S'ÉCHAPPER ET PROVOQUER

UNE CONDITION POTENTIELLEMENT

DANGEREUSE.

Figure # 7

Figure # 6

Figure # 6a

IGNITER

SHIELD

BURNER

SHUTTER

LOCATING

NOTCH

INLET PORT

OPERATING THE GRILL:

U-BURNERS:

Each U-burner is rated at 27,500 BTU. (See figure # 6).

The grill burners encompass the entire cooking area

and are side ported to minimize blockage from falling

grease and debris.

Above the burners there are stainless steel briquette

trays with ceramic briquettes. The briquette tray is a

fundamental part for the performance of the grill. Do

not cook on the grill without them.

Make sure the briquette tray is installed properly

before lighting the burner. Each grill burner has its

own igniter.

The burners are locked in the proper position within

the barbeque unit by the inlet port where the valve

orifice stem is located, the shutter adjustment screw

notch and the rear mounting bracket at the back of

the grill cavity. (See figure # 6a)

USING THE GRILL:

Grilling requires high heat for searing and proper browning. Most foods are cooked at the “HI” heat

setting for the entire cooking time. However, when grilling large pieces of meat or poultry, it may be

necessary to turn the heat to a lower setting after the initial browning. This method will cook the food

through without burning the outside. Foods cooked for a long time or basted with a sugary marinade

may need a lower heat setting near the end of the cooking time.

NOTE: The hot grill sears the food, sealing in the juices. The longer the preheat period, the faster the

meat browns and the darker the sear marks. Place the food on the grill and cook to the desired brown

level. Adjust heat setting, if necessary. The control knob may be set to any position between “HI” and

“LOW”. DO NOT leave the grill unattended while cooking.

SEAR-ZONE™ - IR BURNERS:

Each U-burner is rated at 27,500 BTU. (See figure # 7).

An IR grill works by producing intense heat which quickly sears

the meat. Searing locks in flavor and juices while allowing the

outer surface to absorb smoke and food aroma that is produced

as grease and drippings are vaporized by the burner. The result

is a crisp, flavorful outside with a tender, juicy inside. Just the

result you want with most grilled foods. Sear-Zone™ burners

are located in their proper position by the inlet port and the rear

bracket support of the burner area.

USING THE GRILL:

Grilling requires high heat for searing and proper browning. The intense infrared heat produced by your

™ Gourmet Grill meets these requirements perfectly. Meat is cooked evenly throughout,

while juices, grease and food particles are vaporized upon contact with the burner, giving added flavor

to your food.

NOTE: The hot grill sears the food, sealing in the juices. Proper preheating browns the meat and pro-

duces darker sear marks. Place the food on the grill and sear both sides as recommended on the

“Infrared Grilling Tips” section on page 19. DO NOT leave the grill unattended while cooking.

ROTISSERIE BURNERS:

Your ™ Gourmet Grill is capable of per-

forming back burner rotisserie cooking. The location

of the rear burner allows the placement of the rotis-

serie basting pan (included) beneath the food to col-

lect juices and drippings for basting and gravy. To

flavor the contents of the basting pan, you can add

herbs, onion, garlic, or spices.

To assure that an IR burner is lit, very carefully place your hand 8-10 inches away from the burner sur-

face. If you do not feel the heat of the burner, shut off control knob, wait five minutes, and attempt to re-

light.

ROTISSERIE MOTOR:

The rotisserie motor is capable of turning up to a 50 Lb. cut of meat or poultry, with a maximum diameter

of 12”. The rotisserie motor is an integral part of the grill, mounted on the rear bottom of the unit. The

motor drives a chain and sprocket system to a skewer coupler located your upper cooking area.

The rotisserie motor is electrically grounded by the grill electrical system and plug, therefore the grill

must installed in accordance with local codes or, in the absence of local codes, with the National Electri-

cal Code, ANSI/NFPA 70-1990.

SKEWER:

The skewer for the rotisserie is assembled into the skewer coupler (located right side of the grill) by plac-

ing the pointed end into the square opening of the coupler. The other end of the skewer (round shaft

end) rests between the rotisserie bearing wheels opposite to the skewer coupler, on the left side of the

grill.

To load the skewer, slide the meat holders with the prongs facing towards the center the skewer bar.

Push the skewer through the center of the food, and then slide the second meat holder (prongs toward

the food) onto the skewer.

Center the product to be cooked on the skewer then push the meat holders firmly together. Tighten the

thumb nuts of the meat holders with pliers. It may also be necessary to wrap the food with butcher’s

string (never use nylon or plastic string) to secure any loose portions. Once the food is secure, insert the

skewer into the coupler. Start the motor with the switch located on the right side of the control panel.

ROTISSERIE BASTING PAN:

Your

™ Gourmet Grill includes a basting pan

for use with the rotisserie. Place the pan onto the grill

racks (or, if necessary, directly onto the briquettes if the

grill racks are removed to accommodate large cuts of

meat). This pan will catch drippings from the meat being

cooked, preventing grease build-up on the briquettes or

Sear-Zone™ IR Burner.

NOTE: Never use the basting pan when any of the grill burners are lit. Basting pan is for use with

the rotisserie burner only.

! NOTICE

AVOID WATER DAMAGE TO BURNER NEVER

ALLOW WATER TO CONTACT THE IR BURNER

AS DAMAGE TO THE CERAMIC PANEL WILL

RESULT.

WATER DAMAGE IS NOT COVERED BY YOUR

ALFRESCO WARRANTY

! NOTICE

ALWAYS USE BASTING PAN WITH

ROTISSERIE TO KEEP DRIPPINGS

OFF BURNERS AND BRIQUETTES.

DO NOT USE WHILE GRILLING.

ROTISSERIE GENERAL COOKING INSTRUCTIONS:

As a general rule, rotisserie cooking will take 15 ~ 20 minutes per pound of meat. Keep the hood closed

as much as possible to improve performance.

INFRARED GRILLING TIPS:

Even for an experienced chef, infrared cooking can, at first, present a bit of a challenge. By following

these simple tips, you will soon be producing juicier, more flavorful foods than you have ever

experienced before. As a general rule, foods will cook in less time than they would take on an ordinary

grill.

By turning food frequently (approximately every 2 minutes), excessive charring is simply avoided.

ALFRESCO RECOMMENDS THAT YOU TURN FOOD BEING GRILLED ON A SEAR

ZONE™ IR-BURNER EVERY TWO MINUTES DURING THE COOKING PERIOD.

NEVER ALLOW FOOD TO COOK MORE THAN 2 1/2 MINUTES WITHOUT TURNING.

SEARING IS THE KEY:

An infrared grill works by producing intense heat which quickly sears meats. Searing locks in flavor and

juices while allowing the outer surface to absorb smoke and food aroma that is produced as grease and

drippings are vaporized by the burner. The result is a crisp, flavorful outside with a tender, juicy inside.

Just the result you want with most grilled foods.

HOW TO GRILL WITH IR:

Properly pre-heat the grill by following the lighting instructions on page 12. Place food on grill grids and

turn every 2 to 2 1/2 minutes until food is cooked to desired taste. Do not let food cook more than 2 1/2

minutes without turning. Perfect cross sear marks can be made by rotating food 90° at each turn.

APPROXIMATE SEAR-ZONE™ COOKING TIMES:

 These are recommended times only. Due to the variations on the cuts of meats and personal taste,

your cooking times may be different. Use your discretion when cooking with ALFRESCO™ Gourmet

Grill Sear-Zone™ IR-Burners.

WOOD CHIP SMOKER:

By using real wood chips in the smoker system of your ™ Gourmet Grill, you can add extra

flavor to all of your grilled foods. For good smoke performance, soak the wood chips for not less than 30

minutes, drain excess liquid and fill the smoker tray completely.

HOW TO SMOKE:

1. Fill the smoker tray with thoroughly soaked and drained wood chips.

2. Light the smoker burner according to the instructions on page 12.

Replace the smoker tray into the grill, close the hood and set the smoker burner to high. Smoke should

begin in about 20 ~ 30 minutes

FOOD ITEM APPROXIMATE COOKING TIME

(MINUTES) 

RARE MEDIUM WELL

HAMBURGER -1/2” THICK 4 5 6

STEAK - 1” THICK” 6 8 10

CHICKEN BREAST (BONELESS) 8 ~ 10

CHICKEN BREAST (BONE-IN) 20 ~ 24

REMOVE

GRATE

STEAMER

FRIER

Figure # 8

One tray of wood chips will usually last about one hour. During extended grilling, chips may need to be

added several times. Pull the drawer only partially out of the grill to add chips while in use. Never re-

move the hot smoker tray completely from the grill. To improve smoke performance, keep the hood

closed as much as possible while food is grilling.

NOTE: If not thoroughly soaked, the wood chips will flare up during grilling. To extinguish flames, pull the

drawer slowly a few inches out of the grill front and add a small amount of water. The smoker tray can

also be filled with water to produce steam which can help keep delicate foods moist during grilling.

TYPES OF WOOD CHIPS TO USE:

 Alder: Medium, tart smoke flavor. Excellent on fish, chicken or game.

 Maple: Sweet, hearty smoke flavor. Best with fish, jerky or bacon.

 Apple: Light, sweet smoke flavor. Superb with poultry, ham or sausage.

 Hickory: Heavy smoke flavor. Best with beef, pork or game.

 Mesquite: Light smoke flavor. Excellent on fish, poultry or beef.

 Oak: Heavy smoke flavor. Best with beef, lamb or pork.

 Pecan: Rich, sweet, versatile flavor. Good with any grilled foods.

 Grapevine: Strong smoke flavor. Best with beef or poultry.

STEAMER / FRYER

(OPTIONAL EQUIPMENT):

This optional accessory brings a new level of versatility to your grill, enabling you to deep fry, steam or

boil foods on one side of your ™ Gourmet Grill while grilling on the other. To ensure safe op-

eration and quality results, please follow these instructions:

NOTE: NEVER USE THIS ACCESSORY OVER A SEAR-ZONE™ IR-BURNER.

TO STEAM:

1.Remove the right grate and place the

Steamer/Fryer into the grill as shown

left. (figure # 8)

2.Insert the steaming plate into the

Steamer/Fryer, and add water to just

below the level of the steaming plate.

Be careful not to spill water onto the

burner as damage will result.

3.Place lid onto Steamer/Fryer.

4.Follow lighting instructions on page 12

and bring water to a boil.

5.Reduce heat, remove lid and add food

to be steamed.

When food is cooked to your desired taste,

carefully remove the lid and remove food

from Steamer/Fryer with long-handled

tongs or a slotted spoon.

NEVER ATTEMPT TO REMOVE THIS ACCESSORY FROM THE GRILL WHEN HOT.

ALLOW TO COOL COMPLETELY BEFORE MOVING OR CLEANING.

TO BOIL:

Follow instructions for steaming but leave the steaming plate out. Add as much water as necessary to

cover the foods being cooked, but never fill the Steamer/Fryer more than halfway.

La page charge ...

Alfresco ALXE Grill Manuel utilisateur

Marque: Alfresco

Modèle: ALXE Grill

Catégorie: Barbecues

Taper: Manuel utilisateur

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Alfresco ALXE Grill User manual

Alfresco ALXE Grill Manuel utilisateur

Ce manuel convient également à

Alfresco ALXE Grill Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents