Summers Heat 50-SNC13 Mode d'emploi

INSTALLATION & OPERATION MANUAL







Manufactured By:

England’s Stove Works, Inc.

PO Box 206

Monroe, VA 24574

Rev. 12/2016

Wood Stove

MODELS 13-NC / 50-SNC13 / 50-TNC13

SAVE THESE INSTRUCTIONS

WELCOME!



Introduction

•

 PrecautionaryStatements...........3

•

 ThankYou!……….……………............4



Installation

•

 BeforeInstallation………….….........5

•

 CorrectFlueSize……….....................6

•

 RoomAirBlower….….....................6

•

 FlueSystemGuidelines................7

•

 Floor&WallProtection..............11

•

 SideHeatShields........................13

•

 BrickLayout................................13

•

 Installation…………………..………....14

•

 MobileHomeInstallation...........15

•

 OutsideAirHook‐up………...........15

•

 Chimney………………..



...................16



Operation

•

 Wood……………............................16

•

 BuildingaFire............................17



Maintenance

•

 GlassCare...................................18

•

 GlassGasket................................18

•

 DoorGasket................................19

•

 FiberBoard.................................19

•

 BurnerTubes..............................20

•

 Creosote......................................21

•

 AshDisposal................................21



Questions

•

 HintsandTips.....................................22



PartsandOptions

•

 Parts&OptionsList.............................24

•

 ExplodedView……..............................25

•

 Legs&PedestalInstallation...............25



Warranty

•

 SampleTag..........................................26

•

 Warranty

Details

.................................27

•

 WarrantyRegistrationForm...............28



ImportantInformation

 EPAandSafetyInfo…………….…………30



IMPORTANTNOTES:CLEARANCESMAYONLYBEREDUCEDBYMEANSAPPROVEDBYTHE

REGULATORYAUTHORITYHAVINGJURISDICTION

DONOTCONNECTTOANYAIRDISTRIBUTIONDUCTORSYSTEM.

DONOTBURNGARBAGEORFLAMMABLEFLUIDSSUCHASGASOLINE,NAPHTHAORENGINEOIL.

DONOTUSECHEMICALSORFLUIDSTOSTARTTHEFIRE.

INSTALLATION & OPERATION MANUAL

MODEL NUMBERS: 13-NCMH 50-SNCMH13 50-TNCMH13

13-NCC 50-SNC13C 50-TNC13C

13-NCL 50-SNC13L 50-TNC13L

13-NCP 50-SNC13P 50-TNC13P

13-NCG 50-SNC13G 50-TNC13G

Thank you for purchasing this product from a fine line of heating equipment.

We wish you many years of safe heating pleasure with your new heating appliance.

Save These Instructions.

IMPORTANT: IF YOU HAVE A PROBLEM WITH THIS UNIT DO NOT RETURN IT TO

THE DEALER. CONTACT CUSTOMER SERVICE @ 1-800-245-6489.

Questions? Need Parts or Options? www.heatredefined.com

Please Note the Following Precautionary Statements:

CAUTION: This unit must be installed in accordance with these instructions and

must comply with local building and fire codes. Failure to do so could

result in a chimney or house fire.

Keep children, furniture, fixtures, and all combustible materials away from

any heating appliance. Refer to this owner’s manual for all clearances to

combustible materials.

This stove must be installed in accordance with the Manufactured Home and Safety Standard (HUD),

CFR 3280, Part 24 and must comply with local building and fire codes. Failure to follow these

instructions could result in property damage, bodily injury or even death. Keep children, furniture,

fixtures and combustibles away from any heating appliance.

NOTE: THIS STOVE IS MOBILE HOME AND DOUBLE WIDE APPROVED (WITH OUTSIDE AIR

HOOK-UP) FOR THE PEDESTAL MODEL ONLY – NOT FOR LEG MODELS. DO NOT

INSTALL IN A SLEEPING ROOM. THE STRUCTURAL INTEGRITY OF THE MOBILE

HOME FLOOR, WALL AND CEILING/ROOF MUST BE MAINTAINED.

Read this entire manual before you install and use your new room heater. If this room

heater is not properly installed, a house fire may result. To reduce the risk of fire,

follow the installation instructions. Failure to follow instructions may result in

property damage, bodily injury, or even death.

England’s Stove Works highly recommends the use of smoke detectors and Carbon

Monoxide detectors with any hearth product, including this unit. Follow all manufacturer’s

instructions when using smoke or Carbon Monoxide detectors.

4

Thank you for purchasing this fine product from England’s Stove Works!

England's Stove Works was started, and is still owned by, a family that

believes strongly in a "Do It Yourself" spirit – that’s one reason you found

this product at your favorite “Do It Yourself” store.

We intentionally design and build our stoves so that any homeowner can

maintain his or her unit with basic tools, and we're always more than

happy to show you how to do the job as easily and as inexpensively as

possible.

From our free, downloadable service sheets to our "wizard-style," click-

through Troubleshooting guide on our web site, we have always tried to

help our customers stay "heat-ready," especially when oil and electricity

prices continue to skyrocket.

Please look at our vast Help section on our web site and call our Technical

Support department at (800) 245-6489 if you need any help with your unit.

We are nearly always able to help “walk you through” any repairs,

problems or questions you may have.

PLEASE NOTE: While information obtained on our web site and through

our 800 number is always free of charge, there will be a service charge

incurred with any “on-site” repairs or maintenance that we may arrange.

Wishing you years of efficient, quality and “comfy” heating,

England’s Stove Works

Technical Support Department

www.HeatRedefined.com

(800) 245-6489

This manual is available for free download on the manufacturer’s web site. It is a copyrighted document and resale

is strictly prohibited. The manufacturer may update this manual occasionally and cannot be responsible for

problems including injuries or damages resulting from the use of information found in any manual from

unauthorized sources.

PLEASE NOTE: If you purchased this model from certain stores, their model number may end in “L” “LC” “H”

“CT”

,

etc. This manual does a

pp

l

y

to those models as well.

CAUTION: Stove is heavy.

In addition, when handling any sheet metal products, be aware that there may be sharp edges or burrs.

Although we make every effort to eliminate any sharp edges, please use caution when handling any metal parts.

Remember to disconnect (unplug) the stove from the power source and allow it to completely cool down

before performing any maintenance.

5

CAUTION

If you have any doubt concerning your ability to complete your installation in a professional-like

manner after reading these instructions, you should obtain the services of an installer who is versed in

all aspects as to the correct and safe installation. Do not use temporary, makeshift compromises

during installation.

BEFORE INSTALLATION OF YOUR APPLIANCE

1. HOT WHILE IN OPERATION. KEEP CHILDREN, CLOTHING AND FURNITURE

AWAY. CONTACT MAY CAUSE SKIN BURNS.

2. DO NOT BURN GARBAGE OR FLAMMABLE FLUIDS.

3. Check with the building inspector’s office for compliance with local codes; a permit may be

required.

4. This appliance requires a masonry or prefabricated chimney listed to ULC S629 (Canada) and

UL103HT (U.S.) sized correctly.

5. A 6” diameter flue is required for proper performance.

6. Always connect this unit to a chimney and NEVER vent to another room or inside a building.

7. DO NOT connect to any duct work to which another appliance is connected, such as a furnace.

8. DO NOT connect this unit to a chimney flue serving another appliance.

9. DO NOT USE CHEMICALS OR FLUIDS TO START THE FIRE.

10. The connector pipe and chimney should be inspected periodically and cleaned if necessary.

11. Remember the clearance distances when you place furniture or other objects within the area. DO

NOT store wood, flammable liquids or other combustible materials too close to the unit.

12. Contact your local fire authority for information on how to handle a chimney fire. Have a clearly

understood plan to handle a chimney fire. In the event of a chimney fire, turn air control to a

closed position and CALL THE FIRE DEPARTMENT.

13. DO NOT tamper with the combustion air control beyond normal adjustment.

14. Once the required draw is obtained, operate only with doors closed; open doors slowly when re-

fueling (this will reduce or eliminate smoke from entering the room).

15. Visit our web site at www.heatredefined.com for helpful information, frequently asked questions,

parts/accessory orders and more. Customer Service: (800) 245-6489.

Note on Outside Air Hookup: You can use an outside air hookup with this stove. We highly recommend it for homes

built since the more air-tight construction standards went into effect. This involves connecting a metal pipe (usually

three inches (3”) in diameter - check your stove - and the pipe can be flex or rigid) from the air inlet pipe located on the

bottom rear of the stove through your floor or wall. The outside end of this pipe should be covered in some manner (i.e.

with a screen) to keep it clear of foreign matter. Be sure to keep it above the snowdrift line and clear of leaves and other

debris. It is necessary to use this hookup if installing in a mobile home or double-wide.

A kit is available from England’s Stove Works, Inc. designed for connecting this unit to outside combustion air.

[

Part No. AC-OAK3

]

6

WHY THE CORRECT FLUE SIZE IS IMPORTANT: 6”

“Draft” is the force that moves air from the appliance up through the chimney. The amount of draft in

your chimney depends on the length of the chimney, local geography, nearby obstructions, and other

factors. Too much draft may cause excessive temperatures in the appliance. An uncontrolled burn or

a glowing red part or chimney connector can indicate excessive draft. Inadequate draft may cause

back puffing into the room and “plugging” of the chimney and/or cause the appliance to leak smoke

into the room through appliance and chimney connector joints.

Today’s solid fuel appliances are much more efficient than in the past. The units are designed to give

you controlled combustion, as well as maximum heat transfer, using less fuel to do so.

The design of this heater is such that the exhaust "smoke" is now at lower temperatures than

in the past, requiring proper chimney size to provide adequate draft. If your chimney is too

large, the heater will have a difficult time raising the temperature of the flue enough to provide

adequate draft, which can cause a "smoke back," poor burn, or both.

Should you experience such problems, call in a local chimney expert.

With the door closed, the rate of burning is regulated by the amount of air allowed to enter the unit

through the air control. With experience, you will be able to set the control for heat and burning time

desired.

Attempts to achieve higher output rates that exceed heater design specifications can result in

permanent damage to the heater. The recommended wood load is level with the top of the firebricks.

Overloading may prevent sufficient air entering the heater to properly fuel the fire.

Do not tamper with the combustion air control beyond the normal adjustment capacity.

Operate this heater only with the door closed.

ALWAYS PROVIDE A SOURCE OF FRESH AIR INTO THE ROOM WHERE THE UNIT IS

INSTALLED. FAILURE TO DO SO MAY RESULT IN AIR STARVATION OF OTHER FUEL

BURNING APPLIANCES AND THE POSSIBLE DEVELOPMENT OF HAZARDOUS

CONDITIONS.

THIS HEATER IS EXTREMELY HOT WHILE IN OPERATION. SERIOUS BURNS CAN RESULT

FROM CONTACT. CAUTION SHOULD BE OBSERVED, ESPECIALLY WHEN CHILDREN ARE

PRESENT.

OPTIONAL BLOWER: MODEL AC-16

120 VOLTS, 60Hz, 0.75 AMPS, 2900 RPM

DANGER: RISK OF ELECTRIC SHOCK. DISCONNECT POWER BEFORE SERVICING UNIT.

OPTIONAL BLOWER MOTOR OPERATING INSTRUCTIONS:

This unit is set up for installation of an optional 2-speed blower motor. The fan speed should be

run on “Low” when the unit is operating at lower burn settings, and set to “High” for high burns.

See Illustration 3 (later in this manual) for installation location of your optional blower. Fasten

blower motor to rear heat shield with the four screws that are already provided on your stove. When

routing the power cord, be sure that the cord does not come into contact with any hot surface.

The optional heat circulation blower on this stove requires periodic lubrication; this lubrication should be performed no

less than every three months of normal operation. To properly lubricate the blower, use an eye dropper or similar

dispensing device to drip 5-7 droplets of SAE 20 oil into the oil port on the side of the blower motor.

7

FLUE SYSTEM

1. Existing Flue System

If you have chosen a freestanding unit, this stove is designed to connect to an existing flue system,

such as masonry or a pre-manufactured Class A flue system. If you have a masonry flue system, the

inner liner should be inspected carefully for cracks; if there is no liner in your chimney, we recommend

you install a steel liner or have one installed. If you have an existing pre-manufactured system the

inner liner should be inspected for warping or buckling. Either type chimney system should be

thoroughly cleaned before installing your new stove. We strongly recommend you have a qualified

chimney sweep clean and inspect your entire system, as the sweep can spot problems you might

overlook. The sweep in most cases can make any necessary repairs or recommend a qualified

person to do so. It is not permissible to connect this unit to a chimney that is servicing another

unit.

2. Flue Size

The proper flue size is determined by measuring the inside diameter of the flue collar on the unit.

This stove is equipped with a six inch (6”) TOP EXHAUST FLUE COLLAR. Therefore, the connector

pipe should be six inches (6”) and never less in diameter than the collar on the stove. Your unit may

require an adapter (AC-1677) which will reduce the 6” connector pipe by

1

/

8

”. This is necessary to

accommodate pipe variation from different manufacturers and maintain a good seal. The area of the

chimney liner must also be equal to or greater than the area of the flue collar on the stove. If the area

of the flue is greater than the collar, it should never be more than two and

1

/

2

(2.5) times greater.

The black connector pipe should be 24 gauge steel and a minimum of eighteen inches (18.0”) from

a combustible wall and eighteen inches (18.0”) from ceiling.

3. Installation of a New Flue System

Note: Flue systems and flue pipe are not furnished with the unit.

Masonry Flue: In the event that you plan to install or have a system installed, there are several

approaches that you can take. In the middle and late seventies masonry flue systems became very

popular, and today this type system is satisfactory. If you are considering a masonry system, you

should consult with your local building officials for the proper procedures on this type chimney. We

recommend you consult with and have your flue built by a licensed, bonded contractor. Most masonry

chimney systems are placed against an outside wall and extend upward beside the house. The flue

thimble is then inserted through the wall, making the connection with the stovepipe and the vertical

flue. Exercise extreme caution when drilling through the wall -- you must maintain proper clearance

between the connecting liner and any combustible material in the wall.

We also recommend you have a flue clean-out door located at least two feet (2’) below your

thimble for easy cleaning of the system. This door should be made as airtight as possible. It is the

consumer’s responsibility to ensure the chimney system is safe and in good operating condition.

The manufacturer will not be held responsible for an accident attributed to a unit connected to a faulty

chimney system.

*IMPROPER INSTALLATION: The manufacturer will not be held responsible for damage caused by

the malfunction of a stove due to improper installation. Do not use makeshift methods or material

which may compromise the installation. England’s will not be liable for consequential or indirect

damages to property or persons resulting from the use of this product.

Call (800-245-6489) and/or consult a professional installer if you have any questions.

8

13.0” Min.

Single wall

chimney

connector

18” Min.

USA

Follow all venting system

manufacturer’s

installation requirements

AND their

required clearances.

9

23.5-in 13.5-in 24.5-in

Single Wall

Chimney

Connector

18” Min.

Min. Alcove Width: 64.0-in. Min. Alcove Height: 84.0-in. Max. Alcove Depth: 48.0-in.

CANADA

Follow all venting system

manufacturer’s

installation requirements

AND their

required clearances.

10

INSTALLATION APPLICATIONS, Cont’d.

Illustration 1b

InCanada,theinstallationmustconformtoCAN/CSA‐B365

whenpassingthroughcombustibleconstruction.

11

8”

Pre-Manufactured Flue System: In the past few years pre-manufactured flue systems have

become very popular, because this type system is easily installed and, when done correctly, is very

safe. There are many pre-manufactured flue systems on the market, and when making your choice it

should be U.L. (ULC if Canada), B.O.C.A. or I.C.B.O. approved. Any of these systems are constructed

of the proper materials and meet the proper safety standards. Your local dealer normally handles an

approved brand of flue pipe. There are two very popular methods for installation of this type system.

The first, most popular and least expensive is through the ceiling and out the roof. This is the

most direct route and creates a good draw because it requires less pipe. It is less expensive because

insulated pipe is needed only from the ceiling to the roof and above -- single wall 24 gauge or thicker

pipe is used from the unit to the ceiling if you maintain the proper clearance from all combustible

material.

The second method for installing a pre-manufactured system is to exit through the wall and run

the system vertically up the outside of the structure. This method is more expensive because more

insulated pipe is required -- you must use insulated pipe through the wall and up the outside of the

structure. In either installation, proper clearances to combustibles should be maintained. Your flue

pipe manufacturer furnishes a wall thimble or ceiling support box and, when installed properly, the

correct clearances are achieved. If you are unable to install this type system your local dealer may be

able to recommend a qualified contractor for this installation. It is the customer’s responsibility to

ensure that his system is installed properly and is in good operating condition.

The manufacturer will not be responsible for an accident caused by a unit connected to a faulty

flue system.

FLOOR AND WALL PROTECTION

1. Floor Protection

You will not need any floor protection if your floor

is constructed of a non-combustible material such

as brick or concrete. If your floor is constructed with

a combustible material such as hardwood, carpet or

linoleum, you must place protection between the

stove and the combustible material.

There are many floor and wall board

manufacturers, and you should be very cautious in

choosing the proper protection. The type board you

choose should be U.L. rated and listed (ULC if

Canada). After examining the area you plan to

place your stove and determining it requires a

board, the next step is to select the proper size. The

stove you choose will determine the size board that

is required. The approved protector board should be large enough to provide a minimum of eight

inches (8”, 204mm) behind the unit, eight inches (8”, 204mm) on either side and eighteen inches

(18”, 450mm) in the front where the door is located. This stove requires a minimum of 42.0” D x

41.25” W (1108mm x 1042mm) floor protection.

Installation on a Concrete Floor

An appliance mounted on a concrete floor does not require floor protection.

Carpeting and any other combustible material must not cover the Floor Protector.

If a combustible surface is applied to the concrete floor, a clearance must be maintained

equivalent to the area reserved for the floor protector.

Floor

Protector

USA

Minimum

Size 42.0”

x 41.25”

CANADA:

1108 mm D

x 1042 mm W

18” US (450mm CAN)

(204mm CAN)

(204mm CAN

12

Installation on a Combustible Floor

If the appliance is to be installed on a combustible floor or a combustible floor covering, it must be

installed on a 1” thick non-combustible millboard floor protector or a durable equivalent, with a “R”

factor of no less than “2.” The pad must be installed beneath the unit, extending 16” (U.S.) on the

side equipped with a door, and 8” on all other sides. The pad must cover any horizontal chimney

connector runs and extend 2” beyond each side.

Alternate Floor Protection:

An easy means of determining if a proposed alternate floor protector meets requirements is to

follow this procedure:

1) Convert specification to R-value:

i R-value is given – no conversion is needed

ii k-factor is given with a required thickness (T) in inches: R = 1/k x T

iii C-factor is given: R = 1/C

2) Determine the R-value of the proposed alternate floor protector:

i Use the correct formula given in step 1 (above) to convert values not expressed as “R.”

ii For multiple layers, add R-values of each layer to determine overall R-value.

3) If the overall R-value of the system is greater than the R-value of the specified floor protector,

the alternate is acceptable.

EXAMPLE:

The specified floor protector should be ¾” thick material with a k-factor of 0.84. The proposed

alternate is 4” brick with a C-factor of 1.25 over 1/8” mineral board with a k-factor of 0.29.

Step (a): Use formula above to convert specification to R-value.

R = 1/k x T = 1/0.84 x .75 = 0.893

Step (b): Calculate R of proposed system.

4” brick of C = 1.25, therefore R brick = 1/C =1/1.25 = 0.80

1/8” mineral board of k = 0.29, therefore Rmin.bd. = 1/0.29 x 0.125 = 0.431

Total R = Rbrick + Rmineral board = 0.8 + 0.431 = 1.231

Step (c): Compare proposed system of R of 1.231 to specified R of 0.893. Since proposed

system R is greater than required, the system is acceptable.

Definitions:

Thermal conductance = C = _____Btu____ = ____W____

(hr)(ft

2

)(deg F) (m

2

)(deg K)

Thermal conductivity = k = __(Btu)(inch)__ = ___W____ = ____Btu____

(hr)(ft

2

)(deg F) (m)(deg K) (hr)(ft)(deg F)

Thermal resistance = R = (ft

2

)(hr)(deg F) = (m

2

)(deg K)

Btu W

2. Wall Protection

Please see Illustration 1 for clearances to walls. In some areas local codes may require thirty-six

inches (36”) from a combustible, therefore it is very important that you check with local officials. If

you need to place your unit closer to a combustible wall, some protection will be necessary. If an

approved wall board is used this will reduce your clearance by two thirds (2/3); however, a one inch

(1”) air space has to be between the board and the wall. If you have a ceiling flue hook-up, you will

need protection from the floor to the ceiling if you do not meet the normal clearances. If you have a

wall flue hook up, you will need wall protection at least twelve inches (12”) above the wall thimble.

13

3. Side Heat Shields

This accessory item

comes with the hardware

(six (6) mounting screws)

necessary to install it on

the rear of the stove. This

is a two-piece heat shield,

but is installed one piece at

a time. There are pre-

punched holes on each

side of the Rear Heat

Shield; while holding each

piece of the Side Heat

Shield in place, align the

pre-punched holes in the

Side Heat Shield with the

existing holes in the Rear

Heat Shield, and fasten

with the screws provided.

See Illustration 1 for

clearances with and without

side heat shields.

Rear Heat Shield

Side

Heat

Shield

Side

Heat

Shield

Illustration 3 – Side Heat Shield and Blower Installation

Install AC-16 Optional

Blower on these (4) mounting

holes. See “Optional Blower

Instructions” on page 4 for

instructions.

Illustration 4

BRICK LAYOUT

1 – 9” x 4” x 1.25” brick (Qty. 11)

3 – 4” x 2.5” x 1.25” brick (Qty. 1)

5 – 4” x 4.5” x 1.25” brick (Qty. 1)

7 – 9” x 2.5” x 1.25” brick (Qty. 2)

2 – 9” x 4” x 1.25” brick w/ .75 x .75 notch (Qty. 2)

4 – 4.5” x 4” metal plate (Ash Drawer Plate, Qty. 1)

6 – 9” x 4” x 1.25” brick w/ 1” x 3” notch (Qty. 1)

14

FREESTANDING PLACEMENT AND INSTALLATION

The first problem you may encounter is getting your stove into your home -- all of our stove

products are well constructed, which makes them rather heavy. Three to four adults can normally

handle a unit, but we still recommend using a handcart. Never attempt to handle a heating product

alone!!! The door and brick can be temporarily removed to lighten the unit (refer to Brick Layout).

After the unit is placed into position, install the spring handles and attach any optional equipment.

Chimney Connector Pipe

The black pipe must be six inches (6”) in diameter and at least 24 gauge steel pipe. Do not use

aluminum or galvanized steel pipe, as it will not withstand the extreme temperatures generated by

the stove. Also, do not use single wall connector pipe as a chimney -- you must connect your stove

to a chimney comparable to those listed earlier in this manual. The crimped end of your pipe

should be inserted into the flue collar and, by doing this, all the pipe will be reversed. If you use this

method the creosote will run back down the inside of your pipe and not out of the joints onto your

stove. As a safety precaution, all joints should be sealed with high temperature silicone (AC-RTV3)

and secured with sheet metal screws.

For proper operation the chimney connector should be as short as possible and never exceed a

six foot (6’) horizontal run. Horizontal runs of chimney connector pipe should have an upward slope

of one quarter of an inch (1/4”) per foot. You will need to maintain eighteen inches (18”) of

clearance from the ceiling and eighteen inches (18.0”) from the wall when using single wall

chimney connector.

INSTALLATION

1. Remove all parts from inside the stove body. (If you purchased a leg unit, and it has the factory

packaging, remove the body of the stove from the shroud that it is attached to, referring to

Illustration 7 later in this manual. Those instructions detail how to exchange legs and pedestal,

but removal of the shroud is accomplished in the same manner).

2. Select the proper location for the stove. These appliances must not be installed any closer than

the minimum clearance to combustible materials shown in Illustration 1. The stove must be

installed on a non-combustible surface as shown in Illustration 1 and Illustration 2.

3. If non-combustible materials have been installed on the walls, obtain the minimum clearances

from either the manufacturer of these materials or the local building inspector’s office.

4. Install the stovepipe INSIDE the flue collar on the top of the stove, between the stove and the

chimney.

5. DO NOT use a grate to elevate the fire.

6. A clearance of 18 inches (18”) between the single wall stovepipe and combustible materials is

required. Check with authorities having jurisdiction in your area with any questions.

7. All pipe sections must be connected with the male (crimped) end toward the stove.

8. Fasten the stove pipe to the flue collar by the use of three sheet metal screws. Do the same at

each additional joint to make the entire installation rigid.

9. Maintain the required diameter flue for the entire installation.

10. If you are connecting the stove to an old masonry flue, be sure to have it inspected for cracks

and general condition. Resizing with a stainless steel liner may be required.

11. It is recommended that no more than two 90-degree bends be used in the stovepipe installation.

More than two 90-degree bends may decrease the amount of draw, and possibly cause smoke

spillage.

12. A damper is not required in this installation. Remove the damper plate in the chimney or secure

it in the OPEN position.

FAILURE TO FOLLOW THE MINIMUM CLEARANCE REQUIREMENTS MAY RESULT IN

AN UNSAFE INSTALLATION.

15

13.

Single wall flue pipe assemblies must not exceed 10 feet (10’) in overall length.

Mobile Home Installation

Secure the heater to the floor using the two holes in the pedestal. If the unit is on a combustible

surface, you will need to drill matching holes in the floor protection that you choose (see Floor

Protection section). The wood stove MUST be secured to the floor of the mobile home using lag bolts

and the holes provided in the bottom of the unit for this purpose. Use a #8 copper wire to ground

stove to frame of mobile home. Do not disturb the structural integrity of the home, and be sure the

unit is permanently electrically grounded to the chassis of your home. Remember that outside

combustion air is mandatory, and not to install the unit in a sleeping room of the home.

Be sure to install in accordance with 24 CFR, Part 3280 (HUD).

Outside Air Connection

When installing this model in a mobile home or double wide it is necessary to supply the

combustion air into the unit from outside the dwelling. NOTE: THIS STOVE IS MOBILE HOME AND

DOUBLE WIDE APPROVED (WITH OUTSIDE AIR HOOK-UP) FOR THE PEDESTAL MODEL ONLY

– NOT FOR LEG MODELS.

This can be done by running a thin gauge three inch (3”) pipe (flex or rigid) from the air inlet pipe

located on the rear of the stove through the floor or wall (measure pipe to ensure you obtain the

correct size). The outside end of this pipe should be covered in some manner (i.e. screen) to keep it

clear of foreign matter. Be sure to keep it above the snowdrift line and clear of leaves and other

debris. If you are installing this stove in a regular dwelling this connection is not necessary, but is

recommended in air-tight homes.

A kit is available from England’s Stove Works, Inc. designed for connecting this unit to outside

combustion air. [Part No. AC-OAK3]

16

CHIMNEY

OPERATION

Do not use a grate or elevate the fire. Build the wood fire directly on the bricks. When the stove is

used for the first time, solvents in the paint will smoke off as the stove “cures.”

WOOD –

This heater is designed to burn natural wood only. Higher efficiency and lower emissions

generally result when burning air-dried seasoned hardwood, as compared to softwood or to green or

freshly-cut hardwood.

Use only dry, seasoned wood. Green wood, besides burning at only 60 percent of the fuel value of

dry wood, deposits creosote on the inside of the stove and along the chimney. This can cause

extreme danger of chimney fire. To be called “seasoned,” wood must be dried for a year.

Regardless of whether the wood is green or seasoned, it should be stored in a ventilated, sheltered

area to allow proper drying during the year. Wood should be stored beyond recommended

clearances from combustibles.

DO NOT BURN:

Treated Wood, Garbage, Solvents, Trash, Cardboard, Colored Paper or Coal.

REFER TO CHIMNEY AND CHIMNEY CONNECTOR MANUFACTURER’S INSTRUCTIONS

WARNING: INSTALL VENT AT CLEARANCES SPECIFIED BY THE VENT MANUFACTURER

CONTACT YOUR LOCAL BUILDING AUTHORITY

FOR APPROVED METHODS OF INSTALLATION

1. This appliance requires a masonry or pre-

manufactured chimney listed to UL103HT (ULC

S629 if Canada) sized correctly.

2. If a masonry chimney is used, it is advisable to

have your chimney inspected for cracks, and

check the general condition before installing

your unit. Relining may be required to

reduce the flue diameter to the appropriate

functional size.

3. To help ensure a good draft, the top of the

chimney should be at least 3 feet above the

point of penetration through the roof, and be at

least 2 feet higher than any point of the roof

within 10 feet.

4. The chimney connector shall not pass through

an attic, roof space, closet, concealed space,

floor, ceiling, wall, or any partition of

combustible construction. (Canada: Where

passage through a wall or partition of

combustible construction is desired, the

installation shall conform with CAN/CSA-B365).

5. The minimum overall height of your chimney

should be 15 feet from the floor.

6. Do not use makeshift compromises during

installation.

17

FIRST FIRE –

 Remember to ventilate well.

 Allow the stove to cure before burning for long periods of time at high temperatures.

 Flat spots on the painted surface are normal.

 Shiny spots on the painted surface (before burning) are normal.

 Call Customer Service at (800) 245-6489 if you have any questions.

BUILDING A FIRE

1. Open the air inlet control fully (See Illustration 6).

2. Place a small amount of crumpled paper or approved starter material in the stove.

3. Cover the paper or approved starter material with a generous amount of kindling in a “teepee”

shape, and a few small pieces of wood.

4. Ignite this fuel and close the door most of the way (leave it open slightly).

5. Add larger pieces of wood as the fire progresses, being careful not to overload. Do not fill the

firebox beyond the firebrick area. A coal bed of (ideally) 1” to 2” should be established to

achieve optimum performance.

6. This unit is designed to function most effectively when air is allowed to circulate to all areas of

the firebox. A good way of achieving this is to rake a small (1” to 2” wide) “trough” in the center

of the coal bed, from front to back, prior to loading the fuel.

7. Once fuel has been loaded, close the door and fully open the air inlet control, until the fire is well

established (approximately 20 minutes), being careful not to over-fire.

8. Readjust the air inlet control to the desired burn rate. If excessive smoke fills the firebox, open

the air inlet control slightly, until flames resume and the wood is sufficiently ignited. Basically,

Closed = “Low;” ½ Way Open = “Medium;” and Fully Open = “High.”

9. When refueling, adjust the air control to the fully open position. When the fire brightens,

open the door VERY slowly and carefully. This will prevent gases from igniting and causing

smoke and flame spillage.

10. At this point you may add fuel, being careful not to overload.

NEVER USE GASOLINE, GASOLINE-TYPE LANTERN FUEL, KEROSENE, CHARCOAL

LIGHTER FLUID, OR SIMILAR LIQUIDS TO START OR ‘FRESHEN UP’ A FIRE IN THIS

HEATER. KEEP ALL SUCH LIQUIDS WELL AWAY FROM THE HEATER WHILE IT IS

IN USE.

18

GLASS CARE

The following use and safety tips should be observed:

1. Inspect the glass regularly for cracks or breaks. Surface scratches are acceptable and normal,

but if this glass becomes cracked in any area, the unit should be shut down and the window

replaced with this high-temperature ceramic glass.

2. Do not slam the door or otherwise impact the glass. When closing doors, make sure that logs

or other objects do not protrude and impact the glass.

3. Do not clean the glass with materials which may scratch (or otherwise damage) the glass.

Scratches on the glass can develop into cracks or breaks.

4. Never attempt to clean the glass while the unit is hot. If the deposit is not very heavy, normal

glass cleaners are adequate with a plain, non-abrasive scouring pad. Heavier deposits may be

removed with the use of an oven cleaner.

5. NEVER put substances that can ignite explosively inside the unit, since even small explosions

in confined areas can blow out the glass.

6. This unit has an airwash system, designed to reduce deposits on the glass.

GASKET REPLACEMENT

After extensive use, the sealing material which provides glass and door seal may need to be replaced

if it does not sustain its resilience. Inspect the glass and door seal periodically to ensure proper seal.

If the gaskets become frayed or worn, replace immediately. Contact your dealer or Customer Service

at (800) 245-6489 for approved replacement parts.

The following steps should be followed for replacement of the glass gasket:

1. Ensure that the appliance is not in operation, and is thoroughly cooled.

2. Remove the screws and glass clips.

3. Lift glass out from glass clips.

4. Remove the old gasket, and clean the glass.

5. Replace the new gasket, starting at the bottom of the glass and working along the edges. Be

sure to center the gasket channel on the glass.

6. Trim the gasket to length and butt the ends together.

7. Replace the glass in the door, being sure not to over-tighten the screw and clip.

DO NOT USE SUBSTITUTE MATERIALS. REPLACE GLASS ONLY WITH HIGH-

TEMPERATURE ROBAX PYROCERAM OF THE PROPER SIZE AND THICKNESS.

You may order parts and options on our web site: www.heatredefined.com,

or by calling (800) 516-3636 (parts orders only, call 800-245-6489 for technical questions).

19

The following steps should be followed for replacement of the door gasket:

1. Ensure the appliance is not in operation and is thoroughly cooled.

2. Remove the old door gasket and clean the gasket channel.

3. Using an approved high-temperature gasket cement, apply a thin coat in the bottom of the

channel.

4. Starting at the hinge side of the door, work into the channel around the door unit, trim to length

and butt the ends together.

5. Close the door and allow three to four hours for the cement to set before restarting any fire.

FIBER BOARD: CARE & MAINTENANCE

THIS WOOD HEATER UTILIZES NEW TECHNOLOGY, WHICH INCLUDES A

CERAMIC FIBER BOARD THAT IS LOCATED IN THE FIREBOX,

AND RESTS ON TOP OF THREE (3) STAINLESS STEEL TUBES.

DO NOT REMOVE THIS CERAMIC FIBER BOARD!!!

IT IS A NECESSARY COMPONENT OF THE FIREBOX.

ALSO PLEASE NOTE: THE CERAMIC FIBER BOARD MAY BECOME LOOSE DURING INITIAL

SHIPPING. BE SURE IT IS LYING FLAT, ON TOP OF THE THREE STAINLESS STEEL TUBES,

AND PUSHED ALL THE WAY TO THE BACK OF THE UNIT, WITH NO GAPS BETWEEN IT AND

THE BACK WALL.

Call (800) 245-6489 if questions.

MAINTENACE: This unit is equipped with a ceramic Fiber Board ceiling baffle. After extensive use,

the board should be removed and cleaned.

The following steps should be followed for cleaning or replacement:

1. Ensure the appliance is not in operation and is completely cooled down.

2. There is one screw in each stainless steel tube holder, located in the fire box ceiling. Remove

the screws from the front and middle tube holders.

3. Shift the tube to the right, so that one end comes completely out of the socket. Drop the end

down and pull it out by pulling it back to the left.

4. Drop the board down and push the left corner to the top left. Bring the right corner down to the

bottom right of your door opening, and pull the right side out first.

5. Vacuum the board off and blow the carbon out of the tubes, if there is any build-up.

6. Re-install the board and tubes, reversing the same method they were removed.

20

Placement of Stainless Steel Burner Tubes for all 13-NCMH, 50-SNC13MH and 50-TNC13MH

stove models.

La page charge ...

Summers Heat 50-SNC13 Mode d'emploi

Summers Heat 50-SNC13 Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents