Oracle StorageTek 8 Gb FC PCIe HBA Guide d'installation

Marque: Oracle

Modèle: StorageTek 8 Gb FC PCIe HBA

Taper: Guide d'installation

Part No: E20760-05

March 2015

StorageTek 8 Gb FC PCIe HBA From

QLogic Installation Guide

For HBA Models SG-XPCIE1FC-QF8-Z, SG-PCIE1FC-QF8-

Z, SG-XPCIE1FC-QF8-N, SG-PCIE1FC-QF8-N and SG-

XPCIE2-QF8-Z, SG-PCIE2FC-QF8-Z, SG-XPCIE2-QF8-N, SG-

PCIE2FC-QF8-N, 7106958, 7106957

This software and related documentation are provided under a license agreement containing restrictions on use and disclosure and are protected by intellectual property laws. Except

as expressly permitted in your license agreement or allowed by law, you may not use, copy, reproduce, translate, broadcast, modify, license, transmit, distribute, exhibit, perform,

publish, or display any part, in any form, or by any means. Reverse engineering, disassembly, or decompilation of this software, unless required by law for interoperability, is

prohibited.

The information contained herein is subject to change without notice and is not warranted to be error-free. If you find any errors, please report them to us in writing.

If this is software or related documentation that is delivered to the U.S. Government or anyone licensing it on behalf of the U.S. Government, then the following notice is applicable:

U.S. GOVERNMENT END USERS. Oracle programs, including any operating system, integrated software, any programs installed on the hardware, and/or documentation, delivered

to U.S. Government end users are "commercial computer software" pursuant to the applicable Federal Acquisition Regulation and agency-specific supplemental regulations. As

such, use, duplication, disclosure, modification, and adaptation of the programs, including any operating system, integrated software, any programs installed on the hardware, and/or

documentation, shall be subject to license terms and license restrictions applicable to the programs. No other rights are granted to the U.S. Government.

This software or hardware is developed for general use in a variety of information management applications. It is not developed or intended for use in any inherently dangerous

applications, including applications that may create a risk of personal injury. If you use this software or hardware in dangerous applications, then you shall be responsible to take all

appropriate fail-safe, backup, redundancy, and other measures to ensure its safe use. Oracle Corporation and its affiliates disclaim any liability for any damages caused by use of this

software or hardware in dangerous applications.

Oracle and Java are registered trademarks of Oracle and/or its affiliates. Other names may be trademarks of their respective owners.

Intel and Intel Xeon are trademarks or registered trademarks of Intel Corporation. All SPARC trademarks are used under license and are trademarks or registered trademarks of

SPARC International, Inc. AMD, Opteron, the AMD logo, and the AMD Opteron logo are trademarks or registered trademarks of Advanced Micro Devices. UNIX is a registered

trademark of The Open Group.

This software or hardware and documentation may provide access to or information about content, products, and services from third parties. Oracle Corporation and its affiliates are

not responsible or and expressly disclaim all warranties of any kind with respect to third-party content, products, and services unless otherwise set forth in an applicable agreement

between you and Oracle. Oracle Corporation and its affiliates will not be responsible for any loss, costs, or damages incurred due to your access to or use of third-party content,

products, or services, except as set forth in an applicable agreement between you and Oracle.

Documentation Accessibility

For information about Oracle's commitment to accessibility, visit the Oracle Accessibility Program website at http://www.oracle.com/pls/topic/lookup?ctx=acc&id=docacc.

Access to Oracle Support

Oracle customers that have purchased support have access to electronic support through My Oracle Support. For information, visit http://www.oracle.com/pls/topic/lookup?

ctx=acc&id=info or visit http://www.oracle.com/pls/topic/lookup?ctx=acc&id=trs if you are hearing impaired.

Ce logiciel et la documentation qui l’accompagne sont protégés par les lois sur la propriété intellectuelle. Ils sont concédés sous licence et soumis à des restrictions d’utilisation et

de divulgation. Sauf stipulation expresse de votre contrat de licence ou de la loi, vous ne pouvez pas copier, reproduire, traduire, diffuser, modifier, breveter, transmettre, distribuer,

exposer, exécuter, publier ou afficher le logiciel, même partiellement, sous quelque forme et par quelque procédé que ce soit. Par ailleurs, il est interdit de procéder à toute ingénierie

inverse du logiciel, de le désassembler ou de le décompiler, excepté à des fins d’interopérabilité avec des logiciels tiers ou tel que prescrit par la loi.

Les informations fournies dans ce document sont susceptibles de modification sans préavis. Par ailleurs, Oracle Corporation ne garantit pas qu’elles soient exemptes d’erreurs et vous

invite, le cas échéant, à lui en faire part par écrit.

Si ce logiciel, ou la documentation qui l’accompagne, est concédé sous licence au Gouvernement des Etats-Unis, ou à toute entité qui délivre la licence de ce logiciel ou l’utilise pour

le compte du Gouvernement des Etats-Unis, la notice suivante s’applique:

U.S. GOVERNMENT END USERS. Oracle programs, including any operating system, integrated software, any programs installed on the hardware, and/or documentation, delivered

to U.S. Government end users are "commercial computer software" pursuant to the applicable Federal Acquisition Regulation and agency-specific supplemental regulations. As

such, use, duplication, disclosure, modification, and adaptation of the programs, including any operating system, integrated software, any programs installed on the hardware, and/or

documentation, shall be subject to license terms and license restrictions applicable to the programs. No other rights are granted to the U.S. Government.

Ce logiciel ou matériel a été développé pour un usage général dans le cadre d’applications de gestion des informations. Ce logiciel ou matériel n’est pas conçu ni n’est destiné

à être utilisé dans des applications à risque, notamment dans des applications pouvant causer des dommages corporels. Si vous utilisez ce logiciel ou matériel dans le cadre

d’applications dangereuses, il est de votre responsabilité de prendre toutes les mesures de secours, de sauvegarde, de redondance et autres mesures nécessaires à son utilisation dans

des conditions optimales de sécurité. Oracle Corporation et ses affiliés déclinent toute responsabilité quant aux dommages causés par l’utilisation de ce logiciel ou matériel pour ce

type d’applications.

Oracle et Java sont des marques déposées d’Oracle Corporation et/ou de ses affiliés. Tout autre nom mentionné peut correspondre à des marques appartenant à d’autres propriétaires

qu’Oracle.

Intel et Intel Xeon sont des marques ou des marques déposées d’Intel Corporation. Toutes les marques SPARC sont utilisées sous licence et sont des marques ou des marques

déposées de SPARC International, Inc. AMD, Opteron, le logo AMD et le logo AMD Opteron sont des marques ou des marques déposées d’Advanced Micro Devices. UNIX est une

marque déposée d’The Open Group.

Ce logiciel ou matériel et la documentation qui l’accompagne peuvent fournir des informations ou des liens donnant accès à des contenus, des produits et des services émanant de

tiers. Oracle Corporation et ses affiliés déclinent toute responsabilité ou garantie expresse quant aux contenus, produits ou services émanant de tiers, sauf mention contraire stipulée

dans un contrat entre vous et Oracle. En aucun cas, Oracle Corporation et ses affiliés ne sauraient être tenus pour responsables des pertes subies, des coûts occasionnés ou des

dommages causés par l’accès à des contenus, produits ou services tiers, ou à leur utilisation, sauf mention contraire stipulée dans un contrat entre vous et Oracle.

Accessibilité de la documentation

Pour plus d’informations sur l’engagement d’Oracle pour l’accessibilité à la documentation, visitez le site Web Oracle Accessibility Program, à l'adresse http://www.oracle.com/

pls/topic/lookup?ctx=acc&id=docacc.

Accès au support électronique

Les clients Oracle qui ont souscrit un contrat de support ont accès au support électronique via My Oracle Support. Pour plus d'informations, visitez le site http://www.oracle.com/

pls/topic/lookup?ctx=acc&id=info ou le site http://www.oracle.com/pls/topic/lookup?ctx=acc&id=trs si vous êtes malentendant.

Contents

Using This Documentation .................................................................................. 7

1  HBA Overview ................................................................................................. 9

Kit Contents ................................................................................................... 9

HBA Features and Specifications ....................................................................... 9

HBA Feature Summary ........................................................................... 10

Operating System and Technology Requirements ................................................. 11

System Interoperability ................................................................................... 12

Host Platform Support ............................................................................ 12

Storage Support ..................................................................................... 13

Switch and Director Support .................................................................... 14

Software Support ................................................................................... 15

Boot Support ................................................................................................. 15

Environmental Requirements ............................................................................ 16

2 Hardware Installation and Removal ............................................................... 17

Observing ESD and Handling Precautions .......................................................... 17

Installing the Hardware ................................................................................... 17

▼ To Install the HBA ........................................................................... 18

▼ To Connect the Optical Cable ............................................................. 19

▼ To Apply Power ............................................................................... 20

Testing the Installation .................................................................................... 21

▼ To Verify Proper Installation (Oracle SPARC) ........................................ 21

▼ To Verify Attached Storage (Oracle SPARC) .......................................... 24

▼ To Verify Proper Installation (Oracle x86) ............................................. 24

Replacing the SFP+ Unit on the HBA ............................................................... 27

Removing the Hardware .................................................................................. 27

▼ To Remove the HBA ......................................................................... 27

3 Software Installation ...................................................................................... 29

Contents

6 StorageTek 8 Gb FC PCIe HBA From QLogic Installation Guide • March 2015

Installing Software for the Oracle Solaris OS ...................................................... 29

Installing the Fibre Channel Driver ........................................................... 29

Diagnostic Support for the Oracle Solaris OS .............................................. 30

Installing Software for the Red Hat/SUSE Linux OS ............................................ 30

Downloading the Red Hat/SUSE Linux Drivers ........................................... 31

Installing the Red Hat/SUSE Linux Drivers ................................................ 31

To Load the Newly Built Fibre Channel Driver ........................................... 32

Diagnostic Support for the Red Hat/SUSE OS ............................................ 34

Installing Software for the VMware Technology .................................................. 35

Installing Software for the Windows OS ............................................................ 35

▼ To Download the Fibre Channel Driver ................................................ 35

▼ To Install the Fibre Channel Driver ...................................................... 36

Diagnostic Support for the Windows OS .................................................... 36

Installing a CLI for Updating the BIOS and FCode .............................................. 37

4  Known Issues ................................................................................................ 39

vpd r/w failed Error Messages Are Displayed ................................................. 39

Using This Documentation 7

Using This Documentation

■

Overview – Describes how to install and troubleshoot the host bus adapter

■

Audience – Technicians, system administrators, and authorized service providers

■

Required knowledge – Advanced experience troubleshooting and replacing hardware

Product Documentation Library

Late-breaking information and known issues for this product are included in the documentation

library at http://docs.oracle.com/cd/E19629_01/index.html.

Feedback

Provide feedback about this documentation at http://www.oracle.com/goto/docfeedback.

8 StorageTek 8 Gb FC PCIe HBA From QLogic Installation Guide • March 2015

Chapter1 • HBA Overview 9

1

♦♦♦C H A P T E R  1

HBA Overview

This chapter provides a basic overview of Oracle's single and dual port StorageTek 8 Gb

FC PCI-Express host bus adapter (HBA), which use QLogic technology. This chapter

also describes the various operating systems, host platforms, storage, and infrastructure

configurations that support the HBA and lists the HBA environmental requirements.

This chapter contains the following topics:

■

“Kit Contents” on page 9

■

“HBA Features and Specifications” on page 9

■

“Operating System and Technology Requirements” on page 11

■

“System Interoperability” on page 12

■

“Boot Support” on page 15

■

“Environmental Requirements” on page 16

Kit Contents

■

StorageTek 8 Gb FC PCIe HBA

■

Extra standard bracket

■

Accessing Documentation document

HBA Features and Specifications

The StorageTek 8 Gb FC PCIe HBA (single port: SG-XPCIE1FC-QF8-Z, SG-PCIE1FC-QF8-

Z, SG-XPCIE1FC-QF8-N, SG-PCIE1FC-QF8-N, dual port: SG-XPCIE2FC-QF8-Z, SG-

PCIE2FC-QF8-Z, SG-XPCIE2FC-QF8-N, SG-PCIE2FC-QF8-N, 7106958, 7106957) consists

of a PCI-Express Small Form Factor HBA. The board interfaces an eight-lane PCI-Express bus,

with the eight lanes supporting either one or two Fibre Channel (FC) optical media ports. Each

independent FC port operates at 8 Gbit/sec and features 8/4/2 autonegotiation.

HBA Features and Specifications

10 StorageTek 8 Gb FC PCIe HBA From QLogic Installation Guide • March 2015

HBA Feature Summary

The following is a summary of the HBA features (see Table 1-1 for a detailed list of features):

■

Adherance to the PCI Express Card Electromechanical Specification

■

Solaris Dynamic Reconfiguration support

■

Fibre Channel boot for all supported operating systems

■

Oracle VTS diagnostics support

Fibre Channel Feature Summary

The following is a summary of the Fibre Channel features of the HBA:

■

Support for these FC topologies:

■

FC-SW switched fabric (N_Port)

■

FC-AL arbitrated loop (NL_Port)

■

Point-to-point (N_Port)

■

Removable SFP shortwave optics for attachment to multi-mode fiber with LC-style

connectors

■

Compatibility with:

■

Fibre Channel Physical and Signaling (FC-PH, FC-PH-2, FC-PH-3)

■

Fibre Channel Framing and Signaling (FC-FS)

■

Fibre Channel Physical Interface (FC-PI)

■

Fibre Channel Generic Services (FC-GS-3)

■

Fibre Channel Tape and Medium Changers (FC-Tape)

■

Fibre Channel Protocol for SCSI (FC-FCP)

■

Fibre Channel Protocol for SCSI, 2nd version (FCP-2)

Table 1-1 lists the HBA features and specifications.

TABLE 1-1

HBA Features and Specifications

Feature Description

PCIe connector x8

PCIe signaling environment PCI-Express x8 (8 active lanes)

PCIe transfer rates (maximum) PCI-Express Gen 1 x8 at 2.5 Gbps

PCI-Express Gen 2 x4 at 5 Gbps

Number of FC ports One (single port) or two (dual port)

FC bus type (external) Fiber-optic media, short-wave, multimode fiber

(400‐

M5- SN-S)

FC transfer rate 800 MBps per port maximum, half-duplex

Operating System and Technology Requirements

Chapter1 • HBA Overview 11

Feature Description

1600 MBps per port maximum, full-duplex

FC topologies FC-SW switched fabric (N-Port), FC-AL arbitrated loop (NL-Port), and point-to-point (N-

Port)

Nonvolatile memory Type: Flash (SPI)

Size (total for all ports): 2 MB

Purpose: Firmware, Universal Boot Code, POST Store persistent data, such as driver trace

info Store HBA parameters Store VPD data Non-volatile error log to reduce number of “no

defect found” returned adapters. Error log can wrap around. Software should be able to read

this error-log (IBM request Section 1.6.2)

External FC connectors Two small form-factor pluggable (SFP) multimode optics with LC-style connectors

FC rate: multi-mode optic distance Limited: 2Gb OM1 – 150m OM2 – 300m OM3 – 500m 4Gb OM1 – 70m OM2 – 150m OM3

– 380m 8Gb OM1 – 21m OM2 – 50m OM3 – 150m

Linear: 2Gb OM1 – n/a OM2 – n/a OM3 – n/a 4Gb OM1 – n/a OM2 – n/a OM3 – n/a 8Gb

OM1 – 40m OM2 – 100m OM3 – 300m

LED indicators Three LEDs per FC channel (yellow, green, amber) on front panel as status indicators

Maximum power consumption SG-XPCIE1FC-QF8-Z (single port): 7.3 watts

SG-XPCIE2FC-QF8-Z(dual port): 9.7 watts

Form Factor Low profile MD2, PCI-Express HBA

Operating System and Technology Requirements

The HBA requires the operating system (OS) and technology versions listed in Table 1-2.

TABLE 1-2

Supported Operating System/Technology Versions (Minimum)

Operating System/Technology Supported Versions (minimum)

Oracle Solaris OS for the x86 (64-bit) platform ■ Oracle Solaris 10 1/13 with patches 149176-02 and 145649-04, at minimum

■ Oracle Solaris 11.1 with SRU 7

To obtain the latest patches and SRUs, go to http://support.oracle.com

Oracle Solaris OS for the SPARC (64-bit) platform ■ Oracle Solaris 10 1/13 with patches 149175-02 and 145648-04, at minimum

■ Oracle Solaris 11.1 with SRU 7

To obtain the latest patches and SRUs, go to http://support.oracle.com

Linux OS ■ Oracle Enterprise Linux 5.9 (Red Hat Compatible Kernel (RHCK) and

Unbreakable Enterprise Kernel (UEK) 2, at minimum)

■ Oracle Linux 6.4 (RHCK and UEK2, at minimum)

■ Red Hat Enterprise Linux 5.9 (64-bit)

■ Red Hat Enterprise Linux 6.4 (64-bit)

■ SUSE Linux Enterprise Server 11 SP2 (32-bit and 64-bit)

Microsoft Windows

OS Standard, Enterprise, and

Datacenter Editions

■ Window Server 2008 R2 including SP1 (64-bit)

■ Windows Server 2012

System Interoperability

12 StorageTek 8 Gb FC PCIe HBA From QLogic Installation Guide • March 2015

Operating System/Technology Supported Versions (minimum)

VMware Technology ■ VMware ESX/ESXi 5.0

■ VMware ESX/ESXi 5.1

System Interoperability

This section provides information about selected platforms, storage systems, switches, and

software that are compatible with the heterogeneous FC network design of the HBA. This

section contains the following topics:

■

“Host Platform Support” on page 12

■

“Storage Support” on page 13

■

“Switch and Director Support” on page 14

■

“Software Support” on page 15

Host Platform Support

The HBA is supported by the platforms and operating systems listed in Table 1-3. For up-to-

date information, see your system Product Notes and web pages.

TABLE 1-3

Platform and Operating System Support

Platform Supported OS/Technology

Oracle SPARC Servers

SPARC Enterprise T2000 Oracle Solaris

SPARC Enterprise T5120 Oracle Solaris

SPARC Enterprise T5140 Oracle Solaris

SPARC Enterprise T5220 Oracle Solaris

SPARC Enterprise T5240 Oracle Solaris

SPARC Enterprise T5440 Oracle Solaris

Sun Fire V245 Oracle Solaris

Sun Fire V445 Oracle Solaris

SPARC Enterprise M4000 Oracle Solaris

SPARC Enterprise M5000 Oracle Solaris

SPARC Enterprise M8000 Oracle Solaris

SPARC Enterprise M9000-32 Oracle Solaris

SPARC Enterprise M9000-64 Oracle Solaris

SPARC M5-32

SPARC T4-1 Oracle Solaris

System Interoperability

Chapter1 • HBA Overview 13

Platform Supported OS/Technology

SPARC T4-2 Oracle Solaris

SPARC T5-2 Oracle Solaris

SPARC T5-4 Oracle Solaris

SPARC T5-8 Oracle Solaris

Oracle x86 Systems

Sun Blade X4-2B Oracle Solaris, Linux, VMware, and Windows

Sun Fire X2100 M2 Oracle Solaris, Linux, Windows, VMware

Sun Fire X2200 M2 Oracle Solaris, Linux, Windows, VMware

Sun Fire X4100 M2 Oracle Solaris, Linux, Windows, VMware

Sun Fire X4140 Oracle Solaris, Linux, Windows, VMware

Sun Fire X4200 M2 Oracle Solaris, Linux, Windows, VMware

Sun Fire X4240 Oracle Solaris, Linux, Windows, VMware

Sun Fire X4440 Oracle Solaris, Linux, Windows, VMware

Sun Fire X4600 Oracle Solaris, Linux, Windows, VMware

Sun Fire X4600 M2 Oracle Solaris, Linux, Windows, VMware

Sun Fire X4150 Oracle Solaris, Linux, Windows

Sun Fire X4250 Oracle Solaris, Linux, Windows

Sun Fire X4450 Oracle Solaris, Linux, Windows

Sun Fire X4540 Oracle Solaris, Linux, Windows

Sun Server X2-4 Oracle Solaris, Linux, VMware, and Windows

Sun Server X3-2 Oracle Solaris, Linux, VMware, and Windows

Sun Server X3-2L Oracle Solaris, Linux, VMware, and Windows

Sun Server X4-2 Oracle Solaris, Linux, VMware, and Windows

Sun Server X4-2L Oracle Solaris, Linux, VMware, and Windows

Storage Support

This section lists the arrays, storage systems, chassis, and tape storage devices supported by the

HBA. This section provides the following topics:

■

“Array and System Support” on page 13

■

“Tape Storage Support” on page 14

Array and System Support

The HBA supports connecting to, using a supported switch, the following arrays and systems:

■

StorageTek 2540 array

■

StorageTek 6140 array

System Interoperability

14 StorageTek 8 Gb FC PCIe HBA From QLogic Installation Guide • March 2015

■

StorageTek 6540 array

■

StorageTek 9970 system

■

StorageTek 9980/9985 system

■

Oracle StorageTek 9990 system

Tape Storage Support

The HBA supports connecting to, using a supported switch, the following tape storage devices:

■

StorageTek SL24 tape autoloader

■

StorageTek SL48 tape library

■

StorageTek SL500 modular library

■

StorageTek L1400 tape library

■

StorageTek SL3000 tape library

■

StorageTek SL8500 modular library

■

StorageTek Virtual Tape Library (VTL): VTL Value and VTL Plus

■

StorageTek T10000A and T10000B tape drives

■

StorageTek T9840C tape drive

■

StorageTek T9840D tape drive

■

StorageTek T9940B tape drive

■

IBM and HP LTO3 tape drives

■

IBM and HP LTO4 tape drives

■

Quantum DLT-S4 tape drive

Switch and Director Support

The HBA is supported by the following SAN switches and directors:

■

Brocade DCX backbone switch

■

Brocade 200E switch

■

Brocade 300 switch

■

Brocade 4100 switch

■

Brocade 4900 switch

■

Brocade 5000 switch

■

Brocade 5100 switch

■

Brocade 5300 switch

■

Brocade 7500 switch

■

Brocade Mi10K director

■

Brocade M6140 director

Boot Support

Chapter1 • HBA Overview 15

■

Cisco MDS 9124 24-port multilayer fabric switch

■

Cisco MDS 9134 multilayer fabric switch

■

Cisco MDS 9222i multiservice modular switch

■

Cisco MDS 9509 multilayer director

■

Cisco MDS 9513 multilayer director

■

QLogic SANbox 5600 switch

■

QLogic SANbox 5602 switch

■

QLogic SANbox 5802v switch

■

QLogic SANbox 9000 stackable chassis FC switch series

■

Oracle Storage Fibre Channel Switch 5802

Software Support

The HBA supports the software applications listed in Table 1-4.

TABLE 1-4

Supported Software Applications 

Software (minimum version) Supported OS

Sun Cluster 3.x Oracle Solaris

Sun StorEdge Enterprise Backup Software 7.2/7.3/7.4 Oracle Solaris, Linux, and Windows

Sun StorageTek Availability Suite 3.0/4.0 Oracle Solaris

Sun StorageTek Performance Suite 3.0/4.0 Oracle Solaris

Sun StorageTek Utilization Suite 3.0/4.0 Oracle Solaris

Veritas NetBackup 5.1, 6.x

Oracle Solaris

Veritas Storage Foundation 4.1/5.0 Oracle Solaris

Support for native multi-pathing Oracle Solaris

Boot Support

The HBA supports the following boot types:

■

Oracle Solaris 10 01/13 for the x86 and SPARC environments

■

Oracle Solaris 11.1 for the x86 and SPARC environments

■

Preboot Execution Environment (PXE) boot capable (for x86 systems)

■

RHEL 5.9 and 6.4

■

SLES 11 SP2

■

Oracle Enterprise Linux 5.9 and 6.4

■

VMware ESX/ESXi 5.0 and 5.1

Environmental Requirements

16 StorageTek 8 Gb FC PCIe HBA From QLogic Installation Guide • March 2015

■

Windows Server 2008 R2 including SP1

■

Windows Server 2012

Environmental Requirements

Table 1-5 lists the HBA minimum environmental requirements.

TABLE 1-5

HBA Environmental Requirements

Specification Operating Non-Operating

Temperature 0˚ to 40˚C, noncondensing -40˚C to 70˚C, noncondensing

Humidity 10% to 90% RH, noncondensing, 27˚C max wet bulb 93% RH, noncondensing, 38˚C max wet bulb

Altitude 3000m 12,000m

Vibration 0.20G in all axes, 5–500 Hz sine 1.0G in all axes, 5–500 Hz sine

Shock Operating: 5G, 11 ms half-sine 30G 11 ms half-sine

Chapter2 • Hardware Installation and Removal 17

2

♦♦♦C H A P T E R  2

Hardware Installation and Removal

This chapter describes how to install and remove the HBA. Refer to your system installation or

service manual for detailed instructions.

This chapter contains the following topics:

■

“Observing ESD and Handling Precautions” on page 17

■

“Installing the Hardware” on page 17

■

“Testing the Installation” on page 21

■

“Replacing the SFP+ Unit on the HBA” on page 27

■

“Removing the Hardware” on page 27

Observing ESD and Handling Precautions

Caution - Damage to the HBA can occur as the result of careless handling or electrostatic

discharge (ESD). Always handle the HBA with care to avoid damage to electrostatic sensitive

components.

To minimize the possibility of ESD-related damage, use both a workstation antistatic mat

and an ESD wrist strap. You can get an ESD wrist strap from any reputable electronics store.

Observe the following precautions to avoid ESD-related problems:

■

Leave the HBA in its antistatic bag until you are ready to install it in the system.

■

Always use a properly fitted and grounded wrist strap or other suitable ESD protection

when handling the HBA and observe proper ESD grounding techniques.

■

Hold the HBA by the edge of the PCB, not the connectors.

■

Place the HBA on a properly grounded antistatic work surface pad when it is out of its

protective antistatic bag.

Installing the Hardware

Follow the procedures in this section to install the hardware:

To Install the HBA

18 StorageTek 8 Gb FC PCIe HBA From QLogic Installation Guide • March 2015

■

“To Install the HBA” on page 18

■

“To Connect the Optical Cable” on page 19

■

“To Apply Power” on page 20

To Install the HBA

Attach an ESD wrist strap (see “Observing ESD and Handling

Precautions” on page 17).

Refer to your system installation or service manual to determine an appropriate

PCI-Express slot in which to install the HBA.

Shut down, power off, and unplug the system, if required.

Remove the system case.

Remove the blank panel from an empty PCI-Express slot.

(Optional) Perform the following steps to replace the PCI bracket.

Note - The HBA comes with a low-profile PCI bracket installed. This bracket is approximately

3.11 in. (7.9 cm) long. A standard mounting bracket, which is approximately 4.75 in. (12.6 cm),

is provided with each X-option order.

a.

Remove the SFP(s), if installed.

b.

Remove the mounting bracket screws from the HBA (see Figure 2-1).

FIGURE  2-1

Removing the Bracket Screws

c.

Remove the bracket and store it for future use.

d.

Align the new mounting bracket tabs with the holes in the HBA.

To Connect the Optical Cable

Chapter2 • Hardware Installation and Removal 19

Note - Be careful not to push the bracket past the grounding tabs of the transceiver housing.

Ensure that the LEDs are properly aligned with the holes in the bracket.

e.

Replace the screws that attach the HBA to the bracket.

f.

Reinstall the SFP(s), if removed in Step 6.a.

Insert the HBA into the empty PCI-Express 8-lane slot.

Press firmly until the HBA is seated.

Secure the mounting bracket of the HBA to the case with the panel screw or clip.

10.

Replace the system case and tighten the case screws.

The HBA is now installed and you can connect the optical cables.

To Connect the Optical Cable

Note - The HBA does not allow normal data transmission on an optical link unless it is

connected to another similar or compatible Fibre Channel product (that is, multimode to

multimode).

Use multimode fiber-optic cable, intended for short-wave lasers, that adheres to the

specifications listed in Table 1-1 in Table 1-1.

Connect the fiber-optic cable to an LC connector on the HBA.

Figure 2-2 shows the single port HBA and Figure 2-3 shows the dual port HBA.

FIGURE  2-2

Connecting the Optical Cable: Single Port HBA

To Apply Power

20 StorageTek 8 Gb FC PCIe HBA From QLogic Installation Guide • March 2015

FIGURE  2-3

Connecting the Optical Cable: Dual Port HBA

Connect the other end of the cable to the FC device.

After the optical cable is connected to the HBA, you can power on the system, if required. See

your system installationg and service manual for more information.

To Apply Power

Verify that the HBA is securely installed in the system.

Verify that the correct fiber-optic cable is attached.

Refer to your system installation or service manual to determine how to power

on the system.

Observe the light-emitting diode (LED) status for the power-on self test (POST)

results as shown in the following table..

The yellow, green, and amber LEDs can be seen through openings in the mounting bracket of

the HBA. The following table summarizes the LED status conditions.

Yellow LED Green LED Amber LED State

Off Off Off Power off

On On On Power on (before firmware initialization)

Flash Flash Flash Power on (after firmware initialization)

Flash in sequence

†

Flash in sequenceStep 4 Flash in sequenceStep 4 Firmware fault

Off Off On (for link up) or Flash (if

I/O activity)

2 Gbps link UP/ACT

Off On (for link up) or Flash (if

I/O activity)

Off 4 Gbps link UP/ACT

On (for link up) or Flash (if

I/O activity)

Off Off 8 Gbps link UP/ACT

La page charge ...

Oracle StorageTek 8 Gb FC PCIe HBA Guide d'installation

Marque: Oracle

Modèle: StorageTek 8 Gb FC PCIe HBA

Taper: Guide d'installation

Télécharger le PDF

rapport

dans d''autres langues

English: Oracle StorageTek 8 Gb FC PCIe HBA Installation guide

Oracle StorageTek 8 Gb FC PCIe HBA Guide d'installation

Oracle StorageTek 8 Gb FC PCIe HBA Guide d'installation

dans d''autres langues

Documents connexes

Autres documents