NOMA Milton 5-Reversible blade 6-Speed Le manuel du propriétaire

MILTON

52" LED CEILING FAN

PRODUCT NO. 052-9717-8

USER MANUAL

READ AND SAVE THESE INSTRUCTIONS

2 3

TABLE OF CONTENTS

01. SAFETY/CAUTIONS

02. TOOLS REQUIRED

03. EXPLODED VIEW

04. ELECTRICAL SAFETY

05. ASSEMBLY

06. OPERATION

07. TROUBLESHOOTING

08. DYNAMIC BLADE BALANCING KIT

09. MAINTENANCE

10. WARRANTY & DISPOSAL

4

6

7

10

12

19

20

22

24

25

2

TABLE OF CONTENTS

1. SAFETY/CAUTIONS

2. TOOLS REQUIRED

3. EXPLODED VIEW

4. ELECTRICAL SAFETY

5. ASSEMBLY

6. REMOTE INSTRUCTION

7. TROUBLESHOOTING

8. DYNAMIC BLADE BALANCING

KIT

9. MAINTENANCE

10. WARRANTY & DISPOSAL

4

6

7

10

12

17

19

21

23

24

3

5

01

SAFETY / CAUTIONS

•

TO REDUCE THE RISK OF ELECTRIC SHOCK, ENSURE ELECTRICITY HAS

BEEN TURNED OFF AT THE CIRCUIT BREAKER OR FUSE BOX BEFORE

BEGINNING.

ALL WIRING MUST BE IN ACCORDANCE WITH THE NATIONAL AND

LOCAL ELECTRICAL CODES. ELECTRICAL INSTALLATION SHOULD BE

PERFORMED BY A QUALIFIED LICENSED ELECTRICIAN.

WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK OR FIRE, DO

NOT USE THIS FAN WITH ANY SOLID-STATE FAN-SPEED CONTROL

DEVICE. IT WILL PERMANENTLY DAMAGE THE ELECTRONIC CIRCUITRY.

CAUTION: TO REDUCE THE RISK OF PERSONAL INJURY, USE ONLY THE

SCREWS PROVIDED WITH THE OUTLET BOX.

THE OUTLET BOX AND SUPPORT STRUCTURE MUST BE SECURELY

MOUNTED AND CAPABLE OF RELIABLY SUPPORTING A MINIMUM OF

50 LB (22.7 KG). USE ONLY UL-LISTED OUTLET BOXES MARKED "FOR FAN

SUPPORT."

THE FAN MUST BE MOUNTED WITH A MINIMUM OF 10’ (3.05 M) FROM

THE TRAILING EDGE OF THE BLADES TO THE FLOOR.

AVOID PLACING OBJECTS IN THE PATH OF THE BLADES.

TO AVOID PERSONAL INJURY OR DAMAGE TO THE FAN AND OTHER

ITEMS, BE CAUTIOUS WHEN WORKING AROUND OR CLEANING THE

FAN.

DO NOT USE WATER OR DETERGENTS WHEN CLEANING THE FAN

OR FAN BLADES. A DRY DUST CLOTH WILL BE SUITABLE FOR MOST

CLEANING.

AFTER MAKING ELECTRICAL CONNECTIONS, SPLICED CONDUCTORS

SHOULD BE TURNED UPWARD AND PUSHED CAREFULLY UP INTO

THE OUTLET BOX. THE WIRES SHOULD BE SPREAD APART WITH THE

GROUNDED CONDUCTOR AND THE EQUIPMENT-GROUNDING

CONDUCTOR ON ONE SIDE OF THE OUTLET BOX AND THE

UNGROUNDED CONDUCTOR ON THE OTHER SIDE OF THE OUTLET BOX.

ALL SET SCREWS MUST BE CHECKED AND RE-TIGHTENED WHERE

NECESSARY BEFORE INSTALLATION.

•

WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK

AND PERSONAL INJURY, MOUNT FAN TO OUTLET BOX MARKED

“ACCEPTABLE FOR FAN SUPPORT” WITH THE SCREWS PROVIDED WITH

THE OUTLET BOX

WARNING: TO AVOID RISK OF PERSONAL INJURY, DO NOT BEND THE

BLADE ARMS (ALSO REFERRED TO AS FLANGES) OR THE BRACKETS

WHILE BALANCING THE BLADES OR CLEANING THE FAN. DO NOT

INSERT FOREIGN OBJECTS BETWEEN ROTATING FAN BLADES.

WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK

AND PERSONAL INJURY, MOUNT FAN TO OUTLET BOX MARKED

“ACCEPTABLE FOR FAN SUPPORT” OF 35LB (15.9 KG) OR LESS”

AND USE MOUNTING SCREWS PROVIDED WITH THE OUTLET BOX.

MOST OUTLET BOXES COMMONLY USED FOR THE SUPPORT OF

LIGHT FIXTURES ARE NOT ACCEPTABLE FOR FAN SUPPORT AND MAY

NEED TO BE REPLACED. DUE TO THE COMPLEXITY OF THIS FAN, A

QUALIFIED LICENSED ELECTRICIAN IS STRONGLY RECOMMENDED FOR

INSTALLATION.

ATTENTION: PLEASE ENSURE LED BULBS TOTAL WATTAGE IS ALWAYS

BELOW 70 W!

4

SAFETY / CAUTIONS

SAFETY CONCERNS

•

TO REDUCE THE RISK OF ELECTRIC SHOCK, ENSURE ELECTRICITY HAS

BEEN TURNED OFF AT THE CIRCUIT BREAKER OR FUSE BOX BEFORE

BEGINNING.

ALL WIRING MUST BE IN ACCORDANCE WITH THE NATIONAL AND

LOCAL ELECTRICAL CODES. ELECTRICAL INSTALLATION SHOULD BE

PERFORMED BY A QUALIFIED LICENSED ELECTRICIAN.

WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK OR FIRE, DO

NOT USE THIS FAN WITH ANY SOLID-STATE FAN-SPEED CONTROL

DEVICE. IT WILL PERMANENTLY DAMAGE THE ELECTRONIC CIRCUITRY.

CAUTION: TO REDUCE THE RISK OF PERSONAL INJURY, USE ONLY THE

SCREWS PROVIDED WITH THE OUTLET BOX.

THE OUTLET BOX AND SUPPORT STRUCTURE MUST BE SECURELY

MOUNTED AND CAPABLE OF RELIABLY SUPPORTING A MINIMUM OF

35 LB (15.9 KG). USE ONLY UL LISTED OUTLET BOXES MARKED “FOR FAN

SUPPORT.”

THE FAN MUST BE MOUNTED WITH A MINIMUM OF 10’ (3.05 M) FROM

THE TRAILING EDGE OF THE BLADES TO THE FLOOR.

AVOID PLACING OBJECTS IN THE PATH OF THE BLADES.

TO AVOID PERSONAL INJURY OR DAMAGE TO THE FAN AND OTHER

ITEMS BE CAUTIOUS WHEN WORKING AROUND OR CLEANING THE

FAN.

DO NOT USE WATER OR DETERGENTS WHEN CLEANING THE FAN

OR FAN BLADES. A DRY DUST CLOTH WILL BE SUITABLE FOR MOST

CLEANING.

AFTER MAKING ELECTRICAL CONNECTIONS, SPLICED CONDUCTORS

SHOULD BE TURNED UPWARD AND PUSHED CAREFULLY UP INTO

THE OUTLET BOX. THE WIRES SHOULD BE SPREAD APART WITH THE

GROUNDED CONDUCTOR AND THE EQUIPMENT-GROUNDING

CONDUCTOR ON ONE SIDE OF THE OUTLET BOX AND THE

UNGROUNDED CONDUCTOR ON THE OTHER SIDE OF THE OUTLET BOX.

ALL SET SCREWS MUST BE CHECKED AND RE-TIGHTENED WHERE

NECESSARY BEFORE INSTALLATION.

•WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK

AND PERSONAL INJURY, MOUNT FAN TO OUTLET BOX MARKED

"ACCEPTABLE FOR FAN SUPPORT" WITH THE SCREWS PROVIDED WITH

THE OUTLET BOX.

WARNING: TO AVOID RISK OF PERSONAL INJURY, DO NOT BEND THE

BLADE ARMS (ALSO REFERRED TO AS FLANGES) OR THE BRACKETS

WHILE BALANCING THE BLADES OR CLEANING THE FAN. DO NOT

INSERT FOREIGN OBJECTS BETWEEN ROTATING FAN BLADES.

WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK

AND PERSONAL INJURY, MOUNT FAN TO OUTLET BOX MARKED

"ACCEPTABLE FOR FAN SUPPORT OF 50 LB (22.7 KG) OR LESS"

AND USE MOUNTING SCREWS PROVIDED WITH THE OUTLET BOX. MOST

OUTLET BOXES COMMONLY USED FOR THE SUPPORT OF

LIGHT FIXTURES ARE NOT ACCEPTABLE FOR FAN SUPPORT AND MAY

NEED TO BE REPLACED. DUE TO THE COMPLEXITY OF THIS FAN, A

QUALIFIED LICENSED ELECTRICIAN IS STRONGLY RECOMMENDED FOR

INSTALLATION.

•ATTENTION: PLEASE ENSURE LED BULBS' TOTAL WATTAGE IS ALWAYS

BELOW 70 W!

DO NOT HANG ANY DECORATIONS OR EXTERNAL

ITEMS ONTO THE FAN BLADES. IF FAN STARTS TO WOBBLE, SHUT OFF

POWER IMMEDIATELY. HAVE A QUALIFIED ELECTRICIAN INSPECT IT

BEFORE NEXT USE.

5

•

7

TOOLS REQUIRED

INSTALLATION PREPARATION

03

EXPLODED VIEW

PACKAGE CONTENTS

Flat-head

screwdriver

Cross-head

screwdriver

Safety glasses Pliers

Wire cutters Electrical tape Stepladder Wire strippers

10'

(3.05 m)

30”

(76 cm)

To prevent personal injury and

damage, ensure that the hanging

location allows the blades a

clearance of 10' (3.05 m) from the

floor and 30" (76 cm) from any wall

or obstruction.

This fan can be mounted as a

flushmount on a regular (no-slope)

ceiling only. Downrod installations

are not available for this fan.

blade edge

2 wood screws with at washers

2 5/32” screws with lock washers

1 extra blade bracket screw with

spring washer

16 blade screws with washers

1 “J” hook

1 zip tie

Ceiling Bracket Assembly

Decorative circle

Motor Assembly

Light Plate Assembly

Blade(ABS)

Acrylic lampshade

Accessories bag

Hardware package

Remote control

1

5

1

6

EXPLODED VIEW

PACKAGE CONTENTS

严i



／＼



o:



二＝二

广







＠

恤o

江二]©

中。

�













 











,





EXPLODED VIEW

DETAIL

01.

02.

03.

04.

05.

06.

07.

Ceiling mount plate

Decorative ring

Motor assembly

Blade (ABS)

Light plate

LED

Light shade

8

EXPLODED VIEW

DETAIL

01.

02.

03.

04.

05.

06.

07.

Ceiling Bracket Assembly

Decorative circle

Motor Assembly

Blade(ABS)

Light Plate Assembly

LED

Acrylic lampshade

03

9

11

04

ELECTRICAL SAFETY

Instructions

•

01.

02.

03.

04.

Making the Electrical Connections

•

Read all safety information and installation instructions before

you begin to install the fan and save instructions.

All set screws of the fan must be checked and re-tightened

where necessary before installation.

To reduce the risk of personal injury, do not bend the blade

brackets when installing the brackets, balancing the blades

or cleaning the fan. Do not insert foreign objects between

rotating fan blades.

Before changing the fan direction, turn off the fan and wait for

the fan blades to stop completely.

The safeguards provided by these safety instructions and by

the separate installation instructions are not meant to cover all

possible conditions and situations that may occur. It must be

understood that common sense, caution and care are factors

which can not be built into this product. These factors must be

supplied by the person(s) installing, caring for and operating

the fan.

WARNING: To avoid risk of electric shock, be sure to shut off

power at the main fuse or circuit breaker box before installing

or servicing this xture. Turning off the electrical power by using

the light switch is not sufcient to prevent electric shock.

To reduce the risk of injury, install the fan so that the blades are

at least 10' (3.05 m) above the floor and at least 30" (76 cm)

from the tip of the blades to the wall.

To reduce the risk of re, electric shock, or personal injury,

mount the outlet box marked “ACCEPTABLE FOR FAN

SUPPORT” and use mounting screws provided with the outlet

box.

The installation must be in accordance with the national

electrical code, ANSI/NFPA 70-1999 and local codes. If you

are unfamiliar with the methods of installing electrical wiring,

seek the services of a qualied licensed electrician.

WARNING: To reduce the risk of re, electric shock, or personal

injury, mount to outlet box and use mounting screws provided

with the outlet box.

IMPORTANT: Before you begin installing the fan, carefully read

all information on the separate sheet “SAFETY INSTRUCTIONS”

as well as the following “Installation Steps”. If in doubt, consult

a qualified electrician. Save all

NOTE: The fan weight is 14.537 lb(6.6 kg). Be sure the outlet box

you are using is securely attached to the building structure and

can support the full weight of the fan. Failing to do so can

result in serious injury.

10

ELECTRICAL SAFETY

INSTRUCTIONS

Instructions

•

01.

02.

03.

04.

Making the Electrical Connections

•

Read all safety information and installation instructions before

you begin to install the fan and save instructions.

All set screws of the fan must be checked and re-tightened

where necessary before installation.

To reduce the risk of personal injury, do not bend the blade

brackets when installing the brackets, balancing the blades

or cleaning the fan. Do not insert foreign objects between

rotating fan blades.

Before changing the fan direction, turn off the fan and wait for

the fan blades to stop completely.

The safeguards provided by these safety instructions and by

the separate installation instructions are not meant to cover all

possible conditions and situations that may occur. It must be

understood that common sense, caution and care are factors

which can not be built into this product. These factors must be

supplied by the person(s) installing, caring for and operating

the fan.

WARNING: To avoid risk of electric shock, be sure to shut off

power at the main fuse or circuit breaker box before installing

or servicing this xture. Turning off the electrical power by using

the light switch is not sufcient to prevent electric shock.

To reduce the risk of injury, install the fan so that the blades are

at least 10’ (3.05 m) above the floor and at least 30” (76cm)

from the tip of the blades to the wall.

To reduce the risk of fire, electric shock, or personal injury,

mount an outlet box marked "ACCEPTABLE FOR FAN SUPPORT"

and use mounting screws provided with the outlet box.

The installation must be in accordance with the national

electrical code, ANSI/NFPA 70-1999 and local codes. If you are

unfamiliar with the methods of installing electrical wiring, seek

the services of a qualified licensed electrician.

WARNING: To reduce the risk of fire, electric shock, or personal

injury, mount to outlet box and use mounting screws provided

with the outlet box.

IMPORTANT: Before you begin installing the fan, carefully read

all information on the separate sheet "SAFETY INSTRUCTIONS" as

well as the following "Installation Steps". If in doubt, consult a

qualified electrician.

NOTE: The fan weight is 14 lb 8 oz (6.6 kg). Be sure the outlet

box you are using is securely attached to the building structure

and can support the full weight of the fan. Failing to do so can

result in serious injury.

11

13

02a

Securely attach the mounting plate to

an outlet box marked "ACCEPTABLE FOR

FAN SUPPORT" using the supplied outlet

box screws with spring washers.

03

Assembly on flat surface advisable

for ease of installation.

Insert the decorative ring onto the

fan motor assembly and then

proceed with the next step.

05

ASSEMBLY

INSTRUCTIONS

01

Turn OFF the electric circuit at the main

fuse of circuit breaker box.

06

Hold the main body, the main body of

the four holes aligned with the four

holes of the top plate, and then fix

the screws which are pre-locked on

the ceiling bracket.

07

Align the buckle position of the

decorative ring with the screw head,

and rotate the decorative ring in the

direction of the arrow until it is tight

04

Lift the host and hang the safety

rope reserved for the host on

the hook of the top disk

05Connect the wire reserved for

the host with the remote

control wire, arrange the wire

after connecting the wire, and

place the receiver flat on the

host (for remote control wiring,

refer to the following remote

control wiring diagram

example)

12

02b

With mounting holes in the ceiling

joist, securely attach the mounting

plate to the ceiling, using the two sets

of long wood screws with washers.

12

Turn OFF the electric circuit at the main

fuse of circuit breaker box

01 02a

Securely attach the mounting bracket to

an outlet box marked “ACCEPTABLE FOR

FAN SUPPORT” using the supplied outlet

box screws with spring washers.

02b

Drill two mounting holes in the ceiling joist.

Securely attach the mounting bracket

to the ceiling, using the two sets of long

wood screws with at washers .

03

Insert the decorative ring into the host

machine first and then proceed with

the next step

ASSEMBLY

INSTRUCTIONS

Fig. 1

04

05 Connect the wire reserved

for the motor assembly with

the remote control wire,

arrange the wire after

connecting the wire, and

place the receiver flat on the

host (for remote control

wiring, refer to page 17 for

wiring instructions).

13

Carefully lift the fan motor assembly up

to the mounting bracket and hang the

fan on the hook provided using one of

the holes at the outer rim of the fan

motor assembly.

Use the wood screw and washer to

secure the safety cable to the ceiling

joist or box.

06

Remove two of the four screws (located diagonally from each other) from the

top of the mounting plate and loosen the other two screws .

Align the two key slots in the top of the fan motor assembly with the two

loosened screws on the mounting plate. Push the fan motor assembly up and

turn it clockwise to lock in the mounting plate. Tighten the two screws on the

mounting plate.

Install the two screws that were removed at the beginning of this step into the

remaining two holes and tighten the four screws firmly.

ASSEMBLY

INSTRUCTIONS

14

08

Attach a blade to the fan motor

assembly by inserting the blade into

slots in the side of the fan motor

assembly and aligning the three

screws holes in the blade with the

holes in the center flywheel and

secure with screws. Make sure all the

screws are firmly tightened. Repeat

these steps for the remaining blades.

Attach light plate to motor assembly

with light plate screws

1115

Install the decorative

ring by aligning

the ring's slots with the

screws on the mounting

plate. Rotate the ring

clockwise to lock in

place.

0708 Attach a blade to the fan motor

assembly by inserting the blade into

slots in the side of the fan motor

assembly and aligning the three

screws holes in the blade with the

holes in the centre flywheel and

secure with screws. Make sure all the

screws are firmly tightened. Repeat

these steps for the remaining blades.

Note: Ensure that the blade side

indicated "This side up" is facing the

ceiling for correct blade installation.

09

15

05

ASSEMBLY

INSTRUCTIONS

Connect the LED wires connector

plug exiting the bottom of the fan

motor assembly to the LED socket

of the light plate (10-1), align the

hole of the main connecting LED,

and lock the screws which are pre-

locked on the host to fix the LED

plate (10-2).

Place the shade into the light plate,

aligning the three flat areas on the top

flange of the shade with the raised

dimples in the light kit pan. Turn the

shade clockwise until it stops and is

secure.

Remote control wiring instruction：

Plug the outlet of the remote control and the outlet of the fan body in

accordance with the connecting head. The specific operation is as

follows:

1、The remote control into the power is black or red (L), white (N), and the wall

of the neutral line, live wire docking, connected with the wiring cap

2、The motor line reserved for the host is connected to the motor line output by

the remote control. Red is connected to red, brown to brown, and gray to gray

3、The main engine reserved light line and remote control output light line

docking, direct plug can complete the wiring

16

10-1 10-2

10

11

14

ASSEMBLY

INSTRUCTIONS - CONTINUED

08

Insert the fan blade into the host hole, tighten

the screws with the washers, and repeat this

step for the remaining blades (note that the fan

blade has only one side).

09

Connect the lamp connection line reserved by

the host and the LED socket of the lamp plate,

align the hole of the main connecting plate, and

lock the screws which are pre-locked on the

host to fix the lamp plate

10

The notch position of acrylic lampshade is

aligned with the convex point of the lamp plate,

rotate the acrylic lampshade until it is fasten.

Wiring instructions：

Plug the outlet of the remote control and the outlet of the fan

body in accordance with the connecting head. The specific

operation is as follows:

1. Connect the black wire (L) on the receiver with the live wire from

the outlet box, and connect the white wire (N) on the receiver with

the neutral wire from the outlet box. Connect them by twisting

frayed ends together, using wire connectorsto fasten them.

2. The motor wires from the fan are connected to the motor wire

output from the remote control. Red is connected to red, brown to

brown, and grey to grey. Connect green wire from the fan with the

ground wire from the outlet box.

3. Connect the light wires (blue and white wires set in one quick

connector) from the motor with the blue and white wires (set in one

quick connector) from the receiver. The wiring is complete.

17

INSTRUCTIONS FOR REMOTE

18

OPERATING THE FAN:

A. Install 2 x 1.5 V AAA battery (included). To prevent damage to

the remote, remove the batteries if not used for a long time.

B. Store the remote away from excessive heat or humidity.

C. Operation of the buttons on the panel of the remote:

key — for fan 1 speed

key — for fan 2 speed

key — for fan 3 speed

key — for fan 4 speed

key — for fan 5 speed

key — for fan 6 speed

key — for fan off

key — for light colour, dimming and on/off

key — for fan Foward/Reverse

key — stops the fan after set time elapsed

Press and release light key one time to turn light on or off or switch light

colour. Long press light key when the light is on, it will activate the dimmer

function and the light varies from the current brightness to brighter, or dark

to bright circulatory. User can switch to another light colour and repeat this

step to dim each light colour. When the light is turned on again,the light

memory function will resume the light setting (colour and brightness)

before the light was turned off.

D. Pairing the remote control:

Power off the receiver for five minutes. Turn on the power and

immediately press and hold the key of LIGHT and SPEED3 until the light

turns on, indicating the receiver is paired to the remote.

19

07

TROUBLESHOOTING

COMMON PROBLEMS

PROBLEMPROBLEM SOLUTIONSSOLUTIONS

Fan does not start

•CAUTION: Make sure main power is turned off.

• Check main and branch circuit fuses or circuit

breakers.

•Make sure forward/reverse switch is firmly in left or

right position. Fan will not operate when switch is in

the middle.

• Make sure that the wall control is turned "ON".

• Check line wire connections to fan and switch wire

connections in switch housing.

Fan sounds noisy

• Make sure all screws in motor housing are snug (not

over-tightened).

• Make sure the screws which attach the fan blade

bracket to the motor are tight.

• Make sure wire nut connectors in switch housing are

not rattling against each other or against the interior

wall of the switch housing.

•

CAUTION: Make sure power is turned off before

accessing switch housing.

If using an optional ceiling fan light kit, make sure the

screws securing the glassware are nger-tight. Make

sure light bulbs are tight in sockets and not touching

glass shade(s).

• Some fan motors are sensitive to signals from solid

state variable speed controls. DO NOT USE a solid

state variable speed control.

• Allow "break-in" period of 24 hours. Most noises

associated with a new fan will disappear after this

period.

PROBLEMPROBLEM SOLUTIONSSOLUTIONS

Fan wobbles

•All blades are weighed and grouped by weight.

Natural woods vary in density which could cause the

fan to wobble even though all blades are weight-

matched. The following procedures should eliminate

most of the wobble. Check for wobble after each

step.

•Check that all blades are screwed rmly into blade

brackets.

• Check that all blade brackets are tightened securely

to motor.

• Make sure that canopy and hanger bracket are

tightened securely to ceiling junction box and

junction box is mounted rmly to ceiling joist.

•Most wobble problems of fan are caused when

blades are not in equal level. To check the blade

levels, select a point on the ceiling above the tip of

any blade. Measure the distance from the ceiling to

the blade tip, to an accuracy of 1/8” (3 mm). Rotate

the blades until the next blade is in the measuring

position. Repeat measurement for each blade. If all

blade levels are not equal, you can adjust blade

levels by the following procedure. To adjust a blade

tip down, insert a washer (not supplied) between the

blade and blade bracket at the screw closest to the

motor. To adjust a blade tip up, insert washer (not

supplied) between the blade and blade bracket at

the two screws farthest from the motor.

•Interchanging two adjacent blades could

redistribute the weight and possibly result in smoother

operation.

Light does not work

•Check the blue wire from fan to make sure it is

connected to hot wire from supply wire coming out

of the ceiling.

•Check for loose or disconnected wires in fan switch

housing.

• Check for loose or disconnected wires in light kit.

•Check for faulty light bulbs.

19

18

TROUBLESHOOTING

COMMON PROBLEMS

PROBLEM

SOLUTIONS

Fan does not start

•Check main and branch circuit fuses or circuit

breakers.

•Make sure forward/reverse switch is rmly in left or

right position. Fan will not operate when switch is in

the middle.

•Make sure that the wall control is turned “ON”.

•Check line wire connections to fan and switch wire

connections in switch housing.

• CAUTION: Make sure main power is turned off.

Fan sounds noisy

•Make sure all screws in motor housing are snug (not

over-tightened).

• Make sure the screws which attach the fan blade

bracket to the motor are tight.

• Make sure wire nut connectors in switch housing are

not rattling against each other or against the interior

wall of the switch housing.

•CAUTION: Make sure power is turned off before

accessing switch housing.

• If using an optional ceiling fan light kit, make sure the

screws securing the glassware are nger-tight. Make

sure light bulbs are tight in sockets and not touching

glass shade(s). If vibration persists from glass, remove

glass and install a 1/4”-wide (6 mm) rubber band on

glass neck to act as an insulator. Replace glass and

tighten screws against rubber band.

• Some fan motors are sensitive to signals from solid

state variable speed controls. DO NOT USE a solid

state variable speed control.

•Allow “break-in” period of 24 hours. Most noises

associated with a new fan will disappear after this

period.

PROBLEM

SOLUTIONS

Fan wobbles

Light does not work

•Check the blue wire from fan to make sure it is

connected to hot wire from supply wire coming out

of the ceiling.

•Check for loose or disconnected wires in fan switch

housing.

• Check for loose or disconnected wires in light kit.

•Check for faulty light bulbs.

20

• All blades are weighed and grouped by weight.

Natural woods vary in density which could cause the

fan to wobble even though all blades are weight-

matched. The following procedures should eliminate

most of the wobble. Check for wobble after each

step. Refer page 8

•Check that all blades are screwed firmly into blade

brackets.

• Check that all blade brackets are tightened securely

to motor.

• Interchanging two adjacent blades could

redistribute the weight and possibly result in smoother

operation.

•

Make sure that canopy and hanger bracket are

tightened securely to ceiling junction box and

junction box is mounted firmly to ceiling joist.

Most wobble problems of fan are caused when

blades are not in equal level. To check the blade

levels, select a point on the ceiling above the tip of

any blade. Measure the distance from the ceiling to

the blade tip, to an accuracy of 1/8" (3 mm). Rotate

the blades until the next blade is in the measuring

position. Repeat measurement for each blade. If all

blade levels are not equal, you can adjust blade

levels by the following procedure. To adjust a blade

tip down, insert a washer (not supplied) between the

blade and blade bracket at the screw closest to the

motor. To adjust a blade tip up, insert washer (not

supplied) between the blade and blade bracket at

the two screws farthest from the motor.

La page charge ...

NOMA Milton 5-Reversible blade 6-Speed Le manuel du propriétaire

NOMA Milton 5-Reversible blade 6-Speed Le manuel du propriétaire

Documents connexes

Autres documents