ATMOR AT-912-36TP Manuel utilisateur

www.atmorusa.com

P.N. 105833

Electric Tankless Water Heaters

Thermo Pro2 Series

Model

AT-912-18TP2, AT-912-24TP2, AT-912-29TP2, AT-912-36TP2

Hot Water on Demand

2

Important Safety Guideline

THIS INSTRUCTION MANUAL SHOULD BE SAVED FOR FUTURE REFERENCE.

Denitions: Safety Alert Symbols and Words

This instruction manual uses the following safety alert symbols and words to alert you to hazardous situations and your

risk of personal injury or property damage.

DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious

injury.

WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in death or serious

injury.

CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate

injury.

(Used without word) Indicates a safety related message.

NOTICE: Indicates a practice not related to personal injury which, if not avoided, may result in property

damage.

WARNING: PLEASE READ THIS INSTRUCTION MANUAL THOROUGHLY AND COMPLETELY BEFORE

INSTALLATION & USE. FAILURE TO DO SO COULD CAUSE DAMAGE TO PROPERTY, SERIOUS INJURY OR DEATH,

AND VOID YOUR WARRANTY.

Please contact us directly, should you have any questions regarding your unit. We are available Monday- Friday, 9AM-

5PM EST at:

Phone: 1-844-746-6688

Email: [email protected]

For California residents / Pour les résidents de la Californie / Para residentes en California

WARNING: Cancer and Reproductive Harm -

www.P65Warnings.ca.gov.

AVERTISSEMENT: Cancer et Troubles de l'appareil reproducteur -

www.P65Warnings.ca.gov.

ADVERTENCIA: Cáncer y Daño Reproductivo -

www.P65Warnings.ca.gov.

3

Table of Contents

1. Safety Guidelines ---------------------------------------------------------------------------------------------------------- 04

2. About Your Atmor Electric Tankless Water Heater --------------------------------------------------------------------- 04

3. Selecting an Installation location ----------------------------------------------------------------------------------------- 05

4. Mounting Your Water Heater ----------------------------------------------------------------------------------------- 05-07

5. Plumbing Requirements and Precautions --------------------------------------------------------------------------- 07-08

6. Plumbing Installation ------------------------------------------------------------------------------------------------------ 08

7. Electrical Requirements and Precautions ------------------------------------------------------------------------------- 09

8. Electrical Installation --------------------------------------------------------------------------------------------------- 09-11

9. Flow Rate ------------------------------------------------------------------------------------------------------------------ 12

10. Operation Guide ------------------------------------------------------------------------------------------------------- 12-13

11. Care and Maintenance ---------------------------------------------------------------------------------------------------- 13

12. User Interface/Controls ----------------------------------------------------------------------------------------------- 14-15

13. Troubleshooting -------------------------------------------------------------------------------------------------------- 16-17

14. Reset Unit ------------------------------------------------------------------------------------------------------------------ 18

Before Installing

By installing this product, you acknowledge the terms of the manufacturer’s warranty and authorized dealer’s return

policy. Once the heater is installed, do not return the product to the place of purchase. If you have any questions

regarding the warranty or the product return policies, please contact us by phone or email.

4

1. Safety Guidelines

Please read this manual thoroughly before installing & using the instant water heater. Failure to comply with the safety,

installation or operating instructions will void the product warranty. Manufacturer and distributor of the product will

not be liable for any damage or injury caused by the failure to comply with the installation and operating instructions

specied in this manual or the improper use of the product. Ensure that this product is installed in accordance with the

national, state or local electrical and plumbing codes applicable to your area, and as specied in our instructional guide

to get the best performance from your Instant Water Heater.

This product has more than one power connection source. Do not attempt to install, clean, inspect, disassemble,

service or repair the water heater without shutting o all the power sources to the unit on the main electrical panel

using the circuit breaker.

WARNING: Failure to adhere might result in severe injury or death. The water heater must be installed in

compliance with all national, state, provincial and local electrical and building regulations. We recommend that

you consult a qualied electrician and a qualied plumber if you have questions about anything relating to codes

or regulations for this product.

This product is intended for household and indoor use only. Do not immerse in water.

The breaker used to power this unit must be grounded by means of the electrical panel.

The heater must be directly connected to dedicated circuit breakers on the main electrical panel.

Do not install the heater where it may be subjected to direct sunlight, rain, splashing water, moisture/humidity or

freezing temperatures.

This unit is intended for heating water only. Do not attempt to use the unit for heating any other kind of liquid.

2. About Your Atmor Electric Tankless Water Heater

Congratulations on making the decision to purchase one of the best and nest Instant Water Heaters currently available

in the market today! Your new Instant Water Heater features advanced water ow rate and temperature sensors which

are designed to modulate power to the heating elements to maintain a user-selected output water temperature range

for 18KW/24KW/29KW/36KW: 86°F (30°C) to 122°F (50°C) (subject to the temperature of the incoming water).

WARNING: When selecting the water temperature setting of your Instant

Water Heater’s thermostat, factors such as safety and energy conservation should

be considered. Continuous exposure of the skin to water temperatures above

120°F (49°C) can result in severe burns or death. The maximum temperature

to be set on this Instant Water Heater’s thermostat is 122°F (50°C). Always

take precaution to feel the water before bathing or showering to make sure the

temperatures are not too hot. You are required to read and comply with the Time/

Temperature Relationship Chart on the following page to determine the right water

temperature for your home.

Temperature Exposure time resulting in scalding

120°F (49°C) Around 5 minutes of exposure

122°F (50°C) Around 3 minutes of exposure

You may require a 120°F (49°C) or lower thermostat setting to prevent

contact with “HOT” water, if you have small children, disabled, or elderly persons

in your home. The temperature of the water is regulated by the electronic control on the front of the water heater.

• Children, disabled and

elderly are at high risk of

being scalded.

• See instruction manual

before setting your desired

hot water temperature

• Always feel water before

bathing or showering

5

3. Selecting an Installation Location

• This Water Heater is designed for indoor installation only.

• It should not be installed in a location where it might be subjected to freezing temperatures as the freezing of

the water in the Water Heater can lead to severe and irreversible damages which are not covered under your

warranty.

• The Water Heater should not be placed in a location that is dicult to access.

•

Ensure that the water heater, as well as the power supplies and water connections, are out of reach of

children as the outlet water pipe can get very hot and touching can lead to injury.

• Avoid installing your tankless water heater in a location prone to excessive humidity, moisture, or dust, or in an

area where it may be splashed with water or other liquids. DO NOT install underwater pipes or air conditioning

lines that might leak or condense moisture that could then drip onto the heater. DO NOT install above electrical

boxes or junctions.

• Do not install in areas which can be damaged due to leakage from the Water Heater. However, safety measure

such as suitable drip pan or an active water leak detector and shuto valve should be installed in such areas

that cannot be avoided.

Item # Unit dimensions (inches) Weight (lbs) Connections

AT-912-18TP2 15.55 x 4.49 x 14.25 9.50 1/2”

AT-912-24TP2 18.90 x 4.49 x 14.25 15.13 3/4”

AT-912-29TP2 18.90 x 4.49 x 14.25 15.13 3/4”

AT-912-36TP2 23.23 x 4.99 x 14.25 18.19 3/4”

WARNING: Water heaters are heat producing appliances. In order to avoid damage, injury or death, there shall

be no materials stored against the water heater and proper care shall be taken to prevent unnecessary contact

(especially by children) with the water heater. UNDER NO CIRCUMSTANCES SHALL FLAMMABLE MATERIALS,

SUCH AS GASOLINE OR PAINT THINNER BE USED OR STORED IN THE VICINITY OF THIS WATER HEATER

OR ANY LOCATION FROM WHICH FUMES COULD REACH THE WATER HEATER.

4. Mounting Your Water Heater

1. Your tankless water heater should be secured to a solid mounting surface with four screws, (minimum 1”

(25.4mm) long).

2. Ensure that the unit is level before fastening the screws in place.

3. The unit must be installed in an upright position with the water inlet and outlet at the bottom of the unit. Do not

install inversely with connections facing up or sideways with connections facing right or left.

4. Do not install the unit above electrical boxes or junctions.

5. The water heater must be installed in a manner that prevents contact with ammable liquids and gases. Keep

these ammable materials at least two feet away from the heater and the hot water outlet pipe. The water heater

and the hot water outlet pipe must be secured, and out of children’s reach to prevent tampering with controls or

contact with an extremely hot pipe.

6. If installing the heater on an upper oor or attic, make sure installation complies with the local codes. Install a drip

pan with drainage, or a leak detector and automatic shuto valve, to prevent damage in case of any leakage.

6

a. Remove the appliance cover. (Heater cover) (gure 3)

b. Mount the unit on the wall with 4 screws at the marked points (gure 4)

c. Make sure the unit is leveled horizontally, with water inlets and outlets at the bottom

(g.5)

24kW, 29kW

18W

Fig. 3 Fig. 4

Fig. 5

Do not install upside down

or on its side

Fig. 6

Water Pre-

Filter

Fig. 3 Fig. 4

Fig. 5

Do not install upside down

or on its side

Fig. 6

Water Pre-

Filter

7

Recommended clearances: 12” (304.8mm) above and below the heater 6” (152.4mm) in front of and to the sides of

the heater

CAUTION: Please keep any ammable materials at least 24” (609.6mm) away from the water heater and hot

water outlet pipe.

5. Plumbing Requirements and Precautions

• Please follow all plumbing instructions carefully. This product must be installed in accordance with all national,

state, provincial, and local plumbing codes. We recommend consulting with your municipality or a qualied

plumber if you have questions relating to plumbing codes for your area prior to installing.

• The plumbing installation must be completed before the electrical installation.

• DO NOT solder any pipe with the unit connected to the pipe. The heat from soldering

may cause damage to the ow sensor. Doing so will void the warranty.

• The use of a temperature pressure relief valve (T&P) is not required for most

installations because the tankless water heater does not use a storage tank. UL

Standard 499 does not require that a pressure relief valve is used, although it may

be needed to meet installation codes in your area. In such cases, the pressure relief

valve should be installed in accordance with local codes. It is important to ensure

that the unit is operating correctly, and that air is purged from the valve prior to

installing the water heater.

• A T&P valve is recommended for added safety when connecting to plumbing rated Metal, Flex or High-

Temperature CPVC piping.

NOTE: A pressure relief valve is required for installations in the Commonwealth of Massachusetts

and State of Kentucky. Please check your local installation codes for any special requirements.

• The plumbing installation requires piping that can withstand pressure up to 8 BAR.

Fig. 7

Do not solder any piping

to the unit’s Connection

points

36W

Fig. 3 Fig. 4

Fig. 5

Do not install upside down

or on its side

Fig. 6

Water Pre-

Filter

8

• The maximum operating water pressure for this unit is 150PSI / 10BAR. Residential plumbing systems with

unstable pressure or pressure above 5 BAR require the application of a pressure reduction valve set to 4-5 BAR

for optimal performance.

• The water supply ow rate must be at least 0.5 Gallons per Minute (GPM) to ensure proper operation.

• Flexible water hoses are recommended to be used with your water heater when installing your water heater.

When connecting the inlet water pipe to the unit, use a wrench to hold the unit’s connection, and another wrench

to tighten so that the ow sensor on the unit will not be loosened or damaged. Do not over-tighten the water inlet

and outlet connections to avoid severe internal damage to the water heater.

• We recommend the installation of a manual shut-o valve (ball valve) on the inlet and outlet of the water heater

to create a convenient shut-o point if future maintenance or servicing is required. Before connecting the pipes

to the water heater, it is highly essential to ush the lines to eliminate all the plumbing paste or residue in the lines

caused by any welding or soldering.

• All the water pipes within 3 feet (1 meter) of the inlet and outlet connections are recommended to be rated for

high-temperature applications with 150°F (66°C) minimum.

• Before proceeding to the electrical installation, run water through the unit for several minutes to ush out any air

bubbles from the water line.

6. Plumbing Installation

STEP 1: Thoroughly ush cold supply line of debris.

STEP 2: Connect the HOT WATER line to the water heater OUTLET. The water heater outlet can be seen on the left

side of the heater when facing the unit. Connect the COLD-WATER line to the water heater marked COLD WATER

INLET which is located on the right side when facing the unit.

* Pre-heated water can be connected to the cold water inlet, where this unit will act as a booster.STEP 3: After

tightening both ttings at the water heater, several hot water faucets should be opened to allow the ow of water

through the water heater for at least 2 to 3 minutes. This process purges all the air from the water lines and MUST be

performed before turning on the power at the unit.

FAILURE TO FOLLOW THIS STEP MIGHT CAUSE PERMANENT DAMAGE TO THE HEATING ELEMENTS. (The

power to the heater should be turned o and the air purged out of the lines before turning the power on anytime

maintenance is performed on the water heater or the homes plumbing system, as air might have been introduced into

the plumbing pipes.)

STEP 4: Carefully inspect all connections, units, and the pressure relief device for leaks after the plumbing installation

is completed. If there are no leaks present, you can proceed to the electrical installation.

CAUTION: If you detect a water leak from the water heater at this point, turn o the water supply at the shut o

valve on the unit’s incoming water supply and contact us at 1-844-783-6082.

Plumbing Specications

Minimum water ow to activate the unit 0.5 gpm

Working pressure 0.5–10 BAR (7–150 psi)

Tested pressure (maximum) 20 BAR (290 psi)

Water connections 18kW 1/2” NPT

Water connections 24, 29, 36kW 3/4” NPT

9

7. Electrical Requirements and Precautions

Manufacturer recommends that this product be installed in accordance with all applicable national, state, provincial,

and local electrical codes. Consult a qualied and licensed electrician if you have questions or are unsure about

anything relating to codes for this product. The heater must be connected to a dedicated circuit breaker on the main

electrical panel.

WARNING: As with all electrical appliances, it’s crucial to rst shut o all power to the unit directly at the fuse or

breaker box before attempting to install, repair or disassemble this water heater. Ensure that the breaker is shut o.

SERIOUS BODILY INJURY OR DEATH COULD OCCUR IF YOU IGNORE THIS WARNING.

CAUTION: All wiring (wire gauge), as well as circuit protection (breaker), must comply with the U.S. National

Electrical Code (NEC) in the USA or the Canadian Electrical Code (CEC) in Canada. Failure to do so could lead to

property damage, personal injury, and void your warranty.

Note: The Canadian Electrical Code generally requires that all supply wires and corresponding circuit protection used

for domestic hot water heating and hydronic heating applications be sized to a minimum of 125% of the maximum

current rating of the heater (check heater specication details below).

Before installing this tankless water heater, ensure that sucient electrical power is available in the home to handle

the maximum amperage load of the applicable heater.

IMPORTANT NOTES:

All water heaters heater requires 3 set of wire and ground (see wiring diagram on page 11)

• Please see electrical specications by heater input and wiring diagram on the page 11 for additional electrical

information.

8. Electrical Installation

STEP 1: Take the wire pair and connect to the breaker (see wiring diagram). Be sure that the breaker is connected to

one black wire and one red wire. Be sure the power to the unit is shut o using the dedicated circuit breakers in the

main electrical panel.

STEP 2: Run the correct set of power cable wires from the circuit breaker in the main electrical panel to the water

heater by utilizing a suitable wire gauge which meets all applicable electrical codes for the size of the breaker. Then,

connect the power cable to the block terminal within the water heater.

STEP 3: Unit requires a ground conductor for the incoming circuit.

STEP 4:

DOUBLE CHECK the electrical connections and ensure the wire connections are correct, tight and

secure. It’s important to conrm that the right breaker size and wire gauge has been used and that the unit has been

connected to a ground in accordance with applicable codes. Be sure to reattach the front cover of the unit with two

screws.

STEP 5: Ensure that all the air has been purged from the water lines before turning on power to the unit. Refer to

STEP 3 in the plumbing installation section. Restore power to the unit through the dedicated circuit breaker in the main

electrical panel.

It is crucial to follow the wire connection as shown and ensure all connections are made correctly for

proper operation of the unit. The unit will not operate correctly, even though it turns on and otherwise appears

to function, if you mix up one set of wire with another.

10

Electrical Specications by Heater Input

Item # kW Max

Amps

Required Breaker Req. Wire Size

AT-912-18TP2 18 75 2 x 40A Double Pole 2 x 8/2 AWG with Ground

AT-912-24TP2 24 100 3 x 40A Double Pole 3 x 8/2 AWG with Ground

AT-912-29TP2 29 120.8 3 x 50A Double Pole 3 x 8/2 AWG with Ground

Power Rates

Item # 240V 220V 208V

AT-912-18TP2 18,000 Watts 15,125 Watts 13,520 Watts

AT-912-24TP2 24,000 Watts 20,166 Watts 18,026 Watts

AT-912-29TP2 29,000 Watts 24,368 Watts 21,782 Watts

Terminal Block in Unit

40 Amp

Double Pole

40 Amp

Double Pole

Unit Requires 10 AWG ground wire - one for each 240V circuit

L1L1 L2

8/2 AWG

L2

240V

L1 L2 L1 L2

Wiring Diagram for 18kW

Wiring Diagram for 24kW, 29kW

40 Amp

Double Pole

40 Amp

Double Pole

40 Amp

Double Pole

Unit Requires 10 AWG ground wire - one for each 240V circuit

L1L1L1 L2

8/2 AWG

L2L2

240V

L1 L2 L1 L2 L1 L2

Terminal Block in Unit

11

Electrical Specications by Heater Input

Item # kW Max

Amps

Required Breaker Req. Wire Size

AT-912-36TP2 36 150 4 x 40A Double Pole 4 x 8/2 AWG with Ground

Power Rates

Item # 240V 220V 208V

AT-912-36TP2 36,000 Watts 30,250 Watts 27,040 Watts

Your tankless water heater is now installed and ready to use! Follow the General Operating Instructions to complete

the setup.

Terminal Block in Unit

40 Amp

Double Pole

40 Amp

Double Pole

40 Amp

Double Pole

40 Amp

Double Pole

Unit Requires 10 AWG ground wire - one for each 240V circuit

L1L1L1 L2

8/2 AWG

L2L2

240V

L1 L2 L1 L2 L1 L2

L1 L2

240V

L1 L2

8/2 AWG

Wiring Diagram for 36kW

12

9. Flow Rate

The chart below indicates maximum temperature rise for a given ow rate

TEMPERATURE RISE CHART (GPM)

Item # kW 30°F 40°F 50°F 60°F 70°F

AT-912-18TP2 18 1.75 GPM 2.04 GPM 2.46 GPM 3.06 GPM 4.1 GPM

AT-912-24TP2 24 5.2 GPM 3.95 GPM 3.52 GPM 3.3 GPM 2.4 GPM

AT-912-29TP2 28.8 5.9 GPM 4.5 GPM 3.87 GPM 3.47 GPM 2.8 GPM

AT-912-36TP2 36 6.2 GPM 5.15 GPM 4.4 GPM 3.9 GPM 3.1 GPM

Based on 105°F Output Water Temp / GPM = Gallons Per Minute

10. Operation Guide

Operating your new tankless water heater is similar to using any traditional water heating system. However, it is essential

that you carefully read all setup procedures, operating instructions and tips to ensure the maximum performance and

energy savings from your new water heater. We recommend that all members of the household read these General

Operating Instructions.

This electric water heater is designed to supply hot water. The unit contains heating elements within, capable of heating

water quickly on-demand for as long as you need it. Unlike a conventional tank storage water heater, this unit is a

tankless water heater that does not store hot water. However, once you begin using the system, you will understand it

works like a conventional tank system.

Tankless system delivers hot water instantaneously on demand. Since a tankless system does not waste energy

continually when heating water, i.e. idly sitting and losing heat in a storage tank, it provides signicant energy savings

than a conventional water heater.

With your new system, as soon as you turn on the hot water faucet, the demand for hot water is detected by a

ow sensor, and the high-power heating elements are activated. Sensors continually monitor the water ow rate and

measured the incoming and outgoing water temperature. Data is transmitted to the system logic controls, which

determines the exact amount of power required by heating elements to heat the water to your desired temperature.

It is essential to keep in mind that all tankless water heaters are subject to a maximum ow rate. If this ow rate is

exceeded, the heater will not be capable of suciently heating water.

Also keep in mind that conventional tank heaters are set to high temperatures to prevent running out of hot water

quickly, and thus a large amount of cold water needs to be mixed in to reach a comfortable level for washing and

showering. Since this unit heats water on demand, it is designed to heat to a lower temperature. This means you only

need to mix in a small amount of cold water or none at all.

Your hot water supply may also be aected by the incoming water temperatures as the season diers. During winter,

if the incoming water temperature is frigid, you might not be able to run multiple hot water outlets at the same time as

compared to the summer. However, you can run showers back-to-back without having to wait for the water to heat.

Water Quality: One of the things which should be taken into consideration when installing and maintaining the water

heater is the quality of water. Water conditions outside the recommended levels outlined below are not permitted and

can damage the water heater. We reserve the right to deny any warranty claim regarding damage suered due to use

in water conditions that are not in accordance with the table below. The water must be treated, and the heater ushed

regularly when this product is installed in an area that is known to have hard water that causes scale build-up to prevent

damage to the heat exchanger and heating elements. We recommend that a water treatment device or water softener

should be installed to maintain optimal performance of the water heater in hard water areas.

13

Chart for Recommended Water Quality levels

pH Total

Dissolved

Solid (TDS)

Free

CO2

Total

Hardness

Aluminum Chloride Copper Iron Manganese Zinc

6.5

-

8.5

Up to

500

mg/L

Up to

500

mg/L

Up to 200

mg/L

Up to

0.2

mg/L

Up to 250

mg/L

Up to 1.0

mg/L

Up to

0.3

mg/L

Up to

0.05

mg/L

Up

to 5

mg/L

11. Care and Maintenance

To ensure maximum performance of your water heater and to reduce the risk of a water leak, we recommend the

following maintenance:

• The water heater has minimally required maintenance procedures. Periodic inspections and tests are always

recommended for signs of damage or failure. Any damage, cracks, leakage or weakness should be addressed

and xed immediately. Do not over tighten any of the connections. Over tightening the connection points could

cause severe internal damage to the unit.

• Remember that water heated at higher temperatures produces scale buildup much faster than at lower

temperatures. Having manual shut-o/maintenance valves installed on the inlet and outlet of the water heater

will allow access to ush the unit with a descaling solution. We recommend routine maintenance once a year or

once every six months if the water supply has an unusually high level of mineralization (hard water)

• Clean the pre-lter on the inlet water side once every six months. Wash lightly to remove any debris.

When any form of maintenance is carried out on the water heater or the home’s plumbing system that may introduce

air into the plumbing pipes, it is crucial to power o the water heater and purge the air out of the lines before allowing

the unit to power up.

FAILURE TO DO SO COULD RESULT IN PERMANENT DAMAGE TO THE HEATING ELEMENT AND VOID YOUR

WARRANTY.

When air is introduced into the plumbing system, follow the steps below to ensure the unit can safely resume operation.

1. Shut o all power connections to the unit at the circuit breaker on the main electrical panel.

2. Perform the maintenance or servicing tasks.

3. Open one or more hot water faucets and allow water to run through the unit for several minutes to purge any air

from the heater and water lines.

This step must be performed before turning on power to the heater. Failure to complete this step may

cause permanent damage to the heating elements.

4. Reconnect power to the unit at the circuit breaker on the main electrical panel. Press and switch the ON position.

5. With the water running through the unit, check and reset the temperature if necessary. The recommended

temperature setting is 118°F (48°C).

14

12. User Interface/Controls

Power

• Turn the knob to the right (clockwise) to activate the heater. The display will

light up.

• Turn the knob all the way to the left (counterclockwise) to turn o the heater.

Setting the Output Water Temperature

• To set the temperature, turn on a hot water faucet and allow water to run

through the heater. Turn the knob clockwise to activate the heater and

display the outlet temperature.

• To raise the temperature setting, turn the knob clockwise. To lower the

temperature, turn the know counterclockwise.

• The temperature can be set to a level from 90°F to 122°F (30°C to 50°C).

• A comfortable temperature for bathing and showering is between 98°F and 105°F (37°C to 41°C).

• The recommended temperature setting is 118°F (48°C), which will deliver hot water for all household needs at

a maximum water ow rate.

CAUTION: A higher temperature setting is not recommended, as it can cause severe scalding injuries to

children and elderly persons. Higher temperatures also produce more scale buildup in water heating devices.

115

º

F

Lower

temperature

Raise

temperature

15

Starting the system for the rst time

1. With the water running through the unit, turn the temperature knob clockwise to activate the heater.

2. Turn the knob to adjust the temperature.The recommended temperature setting is 118°F (48°C).

Freezing Temperatures

If the ambient temperature falls below 32°F (0°C), protect the heater from potential damage. Power o the unit using

the dedicated circuit breaker on the main electrical panel. Open a faucet slightly to cause water to ow continuously

through the device at a very low rate, without heating. Restore power to the unit when temperature condition is normal.

If the water inside the heater freezes, it can cause damage that is not covered by warranty. If you suspect water

has frozen within the unit, do not turn it on until you are sure the frozen water has melted, and there are no leaks in the

unit. It is recommended to contact a qualied electrician or the manufacturer for service in this situation.

Digital temperature display

Power & Temperature setting knob

Hot water outlet

(to be connected to the main hot water pipe)

Cold water inlet

16

13. Troubleshooting

Before calling for service, check the troubleshooting list of common issues.

If you are unable to resolve a problem, contact your locally authorized distributor.

PROBLEM

ISSUE

POSSIBLE CAUSE SOLUTION

No hot water

and display do

NOT light up

Power outage or faulty

wiring.

Check the power supply. Check the circuit breakers.

Make sure the breakers at main electrical panel are ON. You may

have a faulty breaker or unit may be wired incorrectly.

Make sure the shuto valve on the unit’s incoming water supply line

is fully open.

The ow rate needed

to activate the heating

element (0.5 gpm) has not

been reached.

Increase the ow rate from the water supply source.

Clean the lter screen on the unit’s water inlet.

No hot water

and display

DOES light up

Reset the unit Refer to manual (Page 18) for diagram of reset points.

Make sure to shut all power on your breaker panel before

attempting to reset unit. All resets must be pressed.

Potential internal part

failure

Please call us for further technical assistance.

Water is

heated, but not

hot enough.

The water ow rate

exceeds the heating

capacity of the heater.

Reduce the water ow rate at the faucet or slightly close the shuto

valve on the unit’s incoming water supply line to reduce the water

ow rate.

Voltage less than 240 Volts The heating elements on your water heater are designed for 240

volts. When used with a lower voltage, they produce less heating

power. You may need to upgrade to a larger input heater.

Crossed Wires. If it’s a new installation, double check the wiring to conrm that it is

correct.

Temperature setting is too

low.

Increase the temperature setting on the unit.

Water pressure is less than

0.5 BAR (7 psi).

Make sure the shuto valve is fully open, and the water supply line is

not blocked.

Mixing too much cold

water

You do not need to mix as much cold water with your tankless water

heater compared to when you use a conventional water heater. You

may also have an anti- scald feature on your faucet that is mixing

cold water. These types of faucets can usually be adjusted to reduce

the amount of cold water mixed.

Thermal loss due to long

pipe run.

As the hot water from the heater runs through the hot water delivery

system to your faucet, some heat will be lost especially if it has long

distance to travel or the pipes are cold. This is normal. You can

compensate for this by increasing the setting on your water heater if

you need/ want hotter water.

Water is

heated, but not

hot enough.

Voltage less than 240 Volts The computer chips in your tankless water heater are programmed

with the expectation that your incoming line voltage is 240 volts. If

you have less than 240 volts [i.e. 208V or 220V], it may aect the

reading on your water heater’s digital display and cause it to read

slightly higher than the actual output temperature. To compensate

for this, increase the setting on your water heater if you need or want

hotter water.

17

Water is too

hot.

The water ow rate

through the heater is too

slow.

Increase the ow rate at the water outlet.

Temperature setting is too

high

Switch to a lower temperature setting.

Water Temperature at

faucet is too hot.

Check for too little ow, or if the set point temperature is too high.

This could possibly indicate a possible internal part failure. Call us for

technical assistance.

Heater shuts

o during use.

Power outage or faulty

wiring.

Check the power supply. Check the circuit breakers.

If the problem persists, please call us for further technical assistance.

Water stops

owing.

Possible Blockage in water

pipes or hoses.

Make sure the main water line valve is fully open, and there are no

obstructions in the water supply line.

Water

temperature

varies from hot

to cold during

use.

Water pressure has

dropped below a minimum

level.

Increase the ow rate from the water supply source.

18

14. Reset Unit

As with all electrical appliances, it is crucial to rst shut o all power to the unit directly at the fuse or breaker box before

attempting to reset this water heater.

WARNING: SERIOUS BODILY INJURY OR DEATH COULD OCCUR IF YOU IGNORE THIS WARNING.

Locate the four reset button locations as shown below and press all buttons. If you hear a “click,” the unit has reset. If

you nd that the unit needs to be reset quite often, please call our customer service for further assistance. Proceed to

turn on your breakers and power on the unit.

18kW

24kW, 29kW

36kW

19

LIMITED WARRANTY

For service, repair or any questions regarding your water heater, call the appropriate 800 number listed within this

section. Please DO NOT return the product to the place of purchase. Also, DO NOT mail the product back to the

manufacturer, nor bring it to a service center without proper instructions and permission from one of our representatives.

The terms of this warranty are solely subject to the original owner and are at no time transferable. A transfer of

ownership will result in immediate termination of this warranty. This warranty is valid only if the product is purchased

from an authorized reseller that has an established direct relationship with the manufacturer.

The manufacturer warrants to the original owner that our instant water heaters will be free from defect in workmanship

and material for TWO YEARS from the date of purchase, and free from leakage for SEVEN YEARS from the date of

purchase. Should any part(s) prove to be defective during this period, the manufacturer will only be responsible for a

replacement water heater or replacement of the defective part(s). The manufacturer is not responsible for labor charges

or any incidental or consequential expenses. If a replacement water heater or part is not available, the manufacturer’s

liability is limited to the cost of the water heater or $1,000.00, whichever is less. The manufacturer is not an insurer, and

the original owner should purchase insurance to cover damage to property or belongings. The original owner agrees

to waive their right to jury trial or to participate in a class action. Also, the original owner agrees to waive subordination

to the extent a loss is covered by insurance, so that their insurance company cannot proceed with action against the

manufacturer for recovery of any claims. Furthermore, all requests must be arbitrated in the state of New Jersey.

Should the owner wish to return the water heater for repair, the owner must rst secure written authorization from

the manufacturer. The owner shall be required to show proof of purchase date and to pay all transportation costs

to return the defective part(s) or water heater for repair or replacement. Warranty is void if: (i) water heater has been

installed or used improperly; (ii) design has been altered in any way; (iii) water heater has been installed and/or serviced

by someone other than a licensed electrician; (iv) or if the water heater has been installed or used in contradiction to

installation instructions, applicable laws and/or ordinances.

Distributed by:

PARAGON GROUP USA LLC

Englewood, NJ 07631

USA

Phone: 1-888-783-6082

Email: [email protected]

Web: www.atmorusa.com

Notes:

La page charge ...

ATMOR AT-912-36TP Manuel utilisateur

ATMOR AT-912-36TP Manuel utilisateur

dans d''autres langues

Autres documents