Ariston AURES PRO 36 240V US Manuel utilisateur

Marque: Ariston

Modèle: AURES PRO 36 240V US

Catégorie: Chauffe-eau

Taper: Manuel utilisateur

Electric Tankless Water Heaters

Chauffe-eau électrique Instantané

Calentador de agua electrico instantaneo

Ce manuel doit être utilisé uniquement par un installateur / technicien de maintenance qualié. Veuillez lire toutes les

instructions de ce manuel avant l’installation. Réalisez les diérentes étapes dans l’ordre indiqué. Dans le cas contraire,

vous pourriez vous exposer à des dommages matériels considérables, des blessures personnelles graves ou la mort.

Le fabricant se réserve le droit d’apporter des modications ou des mises à jour au produit sans aucun préavis et

ne pourra être tenu pour responsables des erreurs typographiques présentes dans la documentation.

NOTE À DESTINATION CONSOMMATEUR: VEUILLEZ CONSERVER TOUTES LES INSTRUCTIONS AFIN DE POUVOIR LES CONSULTER ULTÉRIEUREMENT.

Les surfaces de ces produits en contact avec l’eau potable (consommable) contiennent moins de 0,25% de plomb en

poids, comme l’exige la loi Safe Drinking Water Act, Section 1417, et sont certiées en ce sens par l’IAPMO.

Avertissement relatif à la Proposition 65 de l’État de Californie: ce produit contient des produits chimiques connus dans l’État

de Californie comme susceptibles de causer des cancers, des anomalies congénitales et d’autres troubles de la reproduction.

This manual must only be used by a qualied installer / service technician. Read all instructions in this

manual before installing. Perform steps in the given order. Failure to do so could result in substantial

property damage, severe personal injury, or death.

The manufacturer reserves the right to make product changes or updates without notice and will not be

held liable for typographical errors in literature.

NOTE TO CONSUMER: PLEASE KEEP ALL INSTRUCTIONS FOR FUTURE REFERENCE.

The surfaces of these products contacted by potable (consumable) water contain less than 0.25% lead

by weight as required by the Safe Drinking Water Act, Section 1417, and are certied as such by IAPMO.

California Proposition 65 Warning: This product contains chemicals known to the State of California to

cause cancer, birth defects, or other reproductive harm.

ADVERTENCIA

Este manual solo debe ser utilizado por un técnico de servicio/instalador cualicado. Lea las instrucciones

de este manual antes de instalar el aparato. Siga los pasos en el orden establecido. De lo contrario, puede

causar daños importantes en la propiedad, lesiones graves o incluso la muerte.

AVISO

El fabricante se reserva el derecho de realizar cambios o actualizaciones en el producto sin previo aviso

y no será responsable de los errores tipográcos que haya en el manual.

NOTA PARA EL CONSUMIDOR: GUARDE LAS INSTRUCCIONES PARA FUTURAS CONSULTAS.

Las supercies de estos productos que entra en contacto el agua potable (consumible), contienen menos de 0.25 %

de plomo en peso, tal y como lo exige la ley de agua potable, sección 1417 y están certicadas como tales por IAPMO.

Proposición 65 de California - Advertencia: El estado de California tiene conocimiento de que este producto

contiene sustancias químicas que producen cáncer, defectos congénitos u otros daños reproductivos.

The following dened terms are used throughout this manual to bring attention to the presence of hazards of

various risk levels or to important product information.

DANGER indicates an imminently hazardous situation which, if not avoided, will result in serious personal injury

or death.

WARNING indicates a potentially hazardous situation which, if not avoided, could result in personal injury or

death.

CAUTION indicates a potentially hazardous situation which, if not avoided, may result in moderate or minor

personal injury.

CAUTION used without the safety alert symbol indicates a potentially hazardous situation which, if not

avoided, may result in property damage.

NOTICE is used to address practices not related to personal injury.

Foreword

This manual is intended to be used in conjunction with other literature provided with the water heater. This

includes all related control information. It is important that this manual, all other documents included in this

system, and additional publications be reviewed in their entirety before beginning any work.

Installation should be made in accordance with the regulations of the Authority Having Jurisdiction, local code

authorities, and utility companies which pertain to this type of water heating equipment.

Authority Having Jurisdiction (AHJ) – The AHJ may be a federal, state, local government, or individual such as a

re chief, re marshal, chief of a re prevention bureau, labor department or health department, building ocial

or electrical inspector, or others having statutory authority. In some circumstances, the property owner or his/

her agent assumes the role, and at government installations, the commanding ocer or departmental ocial

may be the AHJ.

NOTE: The manufacturer reserves the right to modify product technical specications and components without

prior notice.

For the Installer

This water heater must be installed by qualied and licensed personnel. The installer should be guided by the

instructions furnished with the water heater, and by local codes and utility company requirements.

Installations Must Comply With:

Local, state, provincial, and national codes, laws, regulations, and ordinances.

The latest version of the National Electrical Code, NFPA No. 70.

Table of Contents

Part 1 - General Safety Information 3

A. When Servicing the Water Heating System 4

B. Heater Water 4

C. Freeze Protection 4

D. Water Temperature Adjustment 4

Part 2 - Prepare the Water Heater 5

A. Locating the Water Heater 5

B. Water Chemistry Requirements 6

C. Technical Specications and Dimensions 7

Part 3 - Installation Instructions 7

A. Wall Mounting the Water Heater 7

B. Plumbing 8

C. Temperature and Pressure Relief 9

D. Scalding 9

E. Filling the Heater 10

Part 4 - Electrical Connection 10

Part 5 - Installation Checklist 11

Part 6 - Operation 12

A. User Interface / Controls 12

B. Start-Up 12

Part 7 - Maintenance 12

A. Removing the Cover 13

B. Draining the Heater 13

C. Removing a Heating Element 13

D. Descaling the Heating Element 13

Part 8 - Troubleshooting 14

A. Resetting the High Limit Switch 15

B. Checking Thermostat Operation 16

C. Changing the Heating Element 16

D. Changing a Triac 16

Part 9 - Replacement Parts 17

Limited Warranty 18

Customer Installation Record Form 20

Part 1 - General Safety Information

This water heater is approved for indoor installations only and is not intended for use as a pool heater. Heater

must have room for service: 6” front and sides, and 12” top and bottom are minimum recommended service

clearances. (A combustible door or removable panel is acceptable front clearance.) This water heater has been

approved for closet installation. Install the water heater in a location where a leak will not result in damage to the

surrounding area. If such a location is not available, install an auxiliary drain pan.

NOTE: Please keep any ammable materials at least 24” (609.6mm) away from the water heater and hot outlet

pipe.

NOTE: Obey all local codes. Obtain all applicable permits before installing the water heater.

NOTE: Install all system components and piping in such a manner that does not reduce the performance of any

re rated assembly.

IMPORTANT SAFETY INSTRUCTIONS

When using electrical appliances, basic safety precautions to reduce the risk of re, electric shock, or injury to

persons should be followed, including:

1. READ ALL INSTRUCTIONS BEFORE USING THIS WATER HEATER.

2. This water heater must be grounded.

3. Install or locate this water heater only in accordance with the provided installation instructions.

4. Use this water heater only for its intended use as described in this manual.

4. This heater has more than one power supply connection point. Never attempt to install, clean, inspect or

repair, disassemble, or service the heater without rst shutting o all power to the unit by means of the circuit

breaker on the main electrical panel.

5. For power supply connection use 8/2 AWG wires or larger, suitable for at least 194

F (90

C).

6. The heater must be connected to a dedicated circuit breaker on the main electrical panel.

7. The plumbing installation must be completed before the electrical installation.

8. The plumbing installation requires metal pipes or reinforced hoses that can withstand pressure up to 145 psi.

9. To ensure proper operation, the water supply ow rate must be at least 0.5 gpm.

10. Do not install the heater where it may be subjected to direct sunlight, rain, splashing water, or freezing

temperatures.

11. Before connecting the unit to a public power network, consult the local power supply authority to ensure

the power network meets the stated requirements.

12. Do not operate this water heater if it has damaged wiring, if it is not working properly, or if it has been

damaged or dropped.

13. This water heater should be serviced only by qualied service personnel. Contact the water heater installer

or a qualied service agency for examination, repair, or adjustment.

SAVE THESE INSTRUCTIONS

Installer - Read all instructions in this manual before installing. Perform steps in the given order.

User - This manual is for use only by a qualied heating installer / service technician. Have this water heater

serviced / inspected annually by a qualied service technician.

FAILURE TO ADHERE TO THE GUIDELINES ON THIS PAGE CAN RESULT IN SUBSTANTIAL PROPERTY

DAMAGE, SEVERE PERSONAL INJURY, OR DEATH.

NOTE: If the water heater is exposed to the following, do not operate. Immediately call a qualied service

technician.

1. Fire

2. Damage

3. Water

Failure to follow this information could result in property damage, severe personal injury, or death.

DO NOT USE THIS WATER HEATER IF ANY PART HAS BEEN SUBMERGED IN WATER. Immediately call

a qualied service technician. The water heater MUST BE replaced if it has been submerged. Attempting to

operate a water heater that has been submerged could create numerous harmful conditions, such as a potential

gas leakage causing a re and/or explosion, or the release of mold, bacteria, or other harmful particulates into

the air. Operating a previously submerged water heater could result in property damage, severe personal injury,

or death.

NOTE: Water heater damage due to ood or submersion is considered an Act of God, and IS NOT covered under

product warranty.

High heat sources (sources generating heat 100

F / 37

C or greater, such as stove pipes, space heaters, etc.) may

damage plastic components of the water heater as well as plastic vent pipe materials. Such damages ARE NOT

covered by warranty. It is recommended to keep a minimum clearance of 8” from high heat sources. Observe

heat source manufacturer instructions, as well as local, state, provincial, and national codes, laws, regulations

and ordinances when installing this water heater and related components near high heat sources.

A. When Servicing the Water Heating System

To avoid electric shock, disconnect electrical supply before performing maintenance.

NOTE: When inquiring about service or troubleshooting, reference the model and serial numbers from the water

heater rating label.

To avoid severe burns, allow water heater and associated equipment to cool before servicing.

B. Heater Water

Do not use petroleum-based cleaning or sealing compounds in a water heating system. Gaskets and seals in the

system may be damaged. This can result in substantial property damage.

Do not use “homemade cures” or “patent medicines”. Damage to the water heater, substantial property damage,

and/or serious personal injury may result.

C. Freeze Protection

NOTE: Consider piping and installation when determining heater location.

Failure of the water heater due to freeze related damage IS NOT covered by product warranty.

NEVER use any toxic chemical, including automotive, standard glycol antifreeze, or ethylene glycol made for

hydronic (non-potable) systems. These chemicals can attack gaskets and seals in water systems, are poisonous

if consumed, and can cause personal injury or death.

Be sure to disconnect electrical power before performing service. Failure to do so could result in electrical shock,

property damage, serious personal injury, or death.

Do not use this water heater for anything other than its intended purpose (as described in this manual). Doing

so could result in property damage and WILL VOID product warranty.

D. Water Temperature Adjustment

The water heater thermostat has been pre-set at

the factory at a temperature equal to or below

125

F (51.7

C) according to UL certication. If the

water heater is going to have a set temperature

above 120

F, it is recommended to use an ASSE

1017 rated mixing valve to avoid severe burns or

death from scalding temperatures.

Approximate Time / Temperature Relationships in Scalds

120

F More than 5 minutes

125

F 1 1/2 to 2 minutes

130

F About 30 seconds

135

F About 10 seconds

140

F Less than 5 seconds

145

F Less than 3 seconds

150

F About 1 1/2 seconds

155

F About 1 second

Table 1 - Approx. Time / Temperature Relationships in Scalds

NOTE: After adjusting the water temperature at

the thermostat, allow the water heater enough

time to heat the water to temperature. After

The manufacturer cannot be responsible for damages caused by improper installation or by failure to follow the

instructions in this manual.

If the ambient temperature falls below 32

F (0

C), protect the heater from potential damage by shutting o

power to the unit by means of the dedicated circuit breaker on the main electrical panel. Open a faucet slightly

to cause water to ow continuously through the device at a very low rate, without heating. Restore power to the

unit when temperature conditions allow.

If the water freezes inside the unit, it can cause damage that is not covered by warranty. If you suspect water has

frozen within the unit, do not turn it on until you are certain the frozen water has melted and there are no leaks in

the unit. It is recommended to contact a qualied electrician or customer service in this situation.

the water heater has stopped heating, use

a thermometer to measure the water temperature at a hot water outlet in the structure. The recommended

temperature setting is 118

UNCRATING THE WATER HEATER - Any claims for damage or shortage in shipment must be led immediately

against the transportation company by the consignee.

Households with small children, disabled, or elderly persons may require a 120

F or lower temperature setting

to prevent severe personal injury or death due to scalding.

Part 2 - Prepare the Water Heater

Remove all sides of the shipping crate to allow the heater to be moved into its installation location.

COLD WEATHER HANDLING - If the water heater has been stored in a very cold location (BELOW 0

F) before

installation, handle with care until the components come to room temperature. Failure to do so could result in

damage to the water heater.

A. Locating the Water Heater

This water heater is certied for indoor use only. DO NOT INSTALL OUTDOORS. Outdoor installations ARE NOT

covered by warranty. Failure to install the water heater indoors could result in property damage, severe personal

injury, or death.

All water heaters eventually leak. Locate the water heater where any leakage from the relief valve, related

piping, tank, or connections will not result in damage to surrounding areas or lower oors of the building.

Any water heater should be installed in such a manner that if it should leak the resulting ow of water will

not cause damage to the area in which it is installed. National Plumbing codes require a drain pan for any

water heater installation. Failure to install one is the sole responsibility of owner and/or installer. Reference UPC

2000 (Uniform Plumbing Code) Section 510 - Protection from Damage or IPC 200 (International Plumbing code)

Section 504 - Safety Devices. Leakage damages ARE NOT covered by warranty.

In addition, water leak detection devices and automatic water shuto valves are readily available at plumbing

supply houses. IT IS HIGHLY RECOMMENDED BY THE MANUFACTURER TO INSTALL WATER LEAK DETECTION

DEVICES AND AUTOMATIC SHUTOFF VALVES IN ANY WATER HEATER INSTALLATION WHERE A LEAKAGE OF

WATER COULD RESULT IN PROPERTY DAMAGES.

1. Installation Area (Mechanical Room) Operating Conditions

• Ensure ambient temperatures are higher than 32

F / 0

C and lower than 104

F / 40

• Avoid continuously high levels of humidity, moisture, or dust, or an area that may be splashed with water or

other liquids. DO NOT install under water pipes or air conditioning lines that might leak or condense onto

the water heater.

• Never close existing ventilation openings

NOTE: When installing in a minimum clearance location, it may not be possible to read or view some product

labeling. It is recommended to make note of the water heater model and serial number.

NOTE: A combustible door or removable panel is acceptable front clearance.

NOTE: Keep water heater and hot outlet piping securely out of the reach of children to prevent tampering with

the controls or contact with an extremely hot pipe.

The service life of the water heater’s exposed metallic surfaces, such as the junction box, is directly inuenced

by proximity to damp and salty marine environments. In such areas higher concentration levels of chlorides

from sea spray coupled with relative humidity can lead to degradation of water heater components and cause

premature water heater failure. Such failures ARE NOT covered by warranty.

Failure of the water heater or components due to incorrect operating conditions IS NOT covered by product

warranty.

Incorrect ambient conditions can lead to damage to the heating system and put safe operation at risk. Ensure

that the installation location adheres to the information included in this manual. Failure to do so could result in

property damage, serious personal injury, or death.

2. Choose a location for the water heater as centralized to the piping and electrical system as possible. Also, locate

the water heater and domestic water piping where it will not be exposed to freezing temperatures. All piping

should be insulated. Additionally, place the water heater so that the drain, controls, and inlets/outlets are easily

accessible.

NOTE: To save on heating costs and improve energy eciency keep the distance between the water heater and

xtures to a minimum to reduce heat loss from excess piping and keep friction loss at a minimum. Ensure all

water heater piping is properly insulated to minimize heat loss.

NOTE: If you do not provide the minimum recommended service clearances it might not be possible to service

the water heater without removing it from the space.

NOTE: In the State of California, the water heater must be braced, anchored, or strapped to avoid moving during

an earthquake. Contact local utilities for code requirements in your area. Visit http://www.dsa.dgs.ca.gov or call

1-916-445-8100 and request instructions.

3. Check area around water heater. Remove any combustible materials, gasoline, and other ammable liquids.

This water heater must not be located near ammable liquids such as gasoline, butane, liqueed propane,

adhesives, solvents, paint thinners, etc., as the controls of this water heater could ignite these vapors and cause

an explosion resulting in property damage, severe personal injury, or death.

This water heater must be installed upright in the vertical position as described in this manual. DO NOT attempt

to install this water heater in any other orientation. Doing so will result in improper water heater operation and

property damage, and could result in serious personal injury or death.

4. If the water heater is to replace an existing water heater, check for and correct any existing system problems

such as:

• System leaks

• Location that could cause the system and water heater to freeze and leak

5. This water heater must be installed vertical on a level surface.

B. Water Chemistry Requirements

Chemical imbalance of the water supply may aect eciency and cause severe damage to the appliance and

associated equipment. Water quality must be professionally analyzed to determine whether it is necessary

to treat the water. Various solutions are available to adjust water quality. Adverse water quality will aect the

reliability of the system. In addition, operating temperatures above 135

F will accelerate the build-up of lime

scale and possibly shorten appliance service life. Failure of an appliance due to lime scale build-up, low pH, or

other chemical imbalance IS NOT covered by the warranty.

The water must be potable, free of corrosive chemicals, sand, dirt, and other contaminates, and meet the

manufacturer’s requirements. It is up to the installer to ensure the water does not contain corrosive chemicals or

elements that can damage the heat exchanger. Potable water is dened as drinkable water supplied from utility

or well water in compliance with EPA secondary maximum contaminant levels (40 CFR Part 143.3). If the water

contains contaminants higher than outlined by the EPA and the manufacturer, water treatment is recommended

and additional, more frequent maintenance may be required. If you suspect that your water is contaminated in

any way, discontinue use of the appliance and contact an authorized technician or licensed professional.

Water Chemistry Requirements

6.5 - 8.5

Chloride

Less than 250 mg/L

Total Dissolved Solids (TDS)

Less than 500 mg/L

Copper

Less than 1.0 mg/L

Free CO2 Iron

Less than 0.3 mg/L

Total Hardness

Less than 200 mg/L

Manganese

Less than 0.05 mg/L

Aluminum

Less than 0.2 mg/L

Zinc

Less than 5 mg/L

*NOTE: To promote appliance service life, it is strongly recommended to follow the maintenance procedures in

this manual.

Table 2 - Water Chemistry Requirements

Failure of electric elements due to lime scale build-up on the heating surface, low pH, or other imbalance IS NOT

covered by the warranty.

C. Technical Specications and Dimensions

Model *Wattage (kW) Max Amperage Required Breaker(s) Required Wire Size

18kW 18 75 3 x 30A Double Pole 3 x 10 AWG w/ Ground

24kW 24 100

3 x 40A Double Pole 3 x 8 AWG w/ Ground

27kW 27 112.5

36kW 36 150 4 x 40A Double Pole 4 x 8 AWG w/ Ground

Technical Data All Models

Minimum Water Flow to Activate

Unit

0.5 gpm

Working Pressure 7 - 150 psi (0.5 - 10 bar)

Tested Pressure 290 psi (20 bar)

Water Connections 3/4” NPT

Elements

18 - 27kW 2

36kW 3

Dimensions

18 - 27kW 20.7” (526 mm) Width x 13.3” (339 mm) Height x 4.5” (114 mm) Depth

36kW 25” (636 mm) Width x 13.3” (339 mm) Height x 4.5” (114 mm) Depth

Weight (Empty)

18 - 27kW 12.17 lb (5.52 kg)

36kW 16.23 lb (7.36 kg)

Temperature Range 86 - 122

F (30 - 50

Table 3 - Technical Specications - *Wattage based on maximum voltage.

Part 3 - Installation Instructions

A. Wall Mounting the Water Heater

1. Remove the two (2) screws attaching the water heater front cover. Remove the front cover. (Figure 1.)

• Do not install the unit above electrical boxes or junctions.

• The mounting surface must be solid and secure.

2. Position the unit on the mounting surface. Ensure the unit is level. Mount the unit to the wall with four (4)

screws of at least one (1) inch (25.4mm) in length at the marked points. See Figure 2.

Use screws suitable for the wall material and the weight of the water heater. Failure to do so could result in

property damages and damage to the water heater. Such damages ARE NOT covered by product warranty.

• The appliance must be mounted horizontally, with water inlets and outlets at the bottom. See Figure 3.

This water heater must be installed upright in the vertical position as described in this manual. DO NOT attempt

to install this water heater in any other orientation. Doing so will result in improper water heater operation and

property damage, and could result in serious personal injury or death.

Temperature Rise Δt (

Flow Rate (GPM)

18kw 24kw 27kW 36kW

35 3.51 4.68 5.26 7.02

45 2.73 3.64 4.09 5.46

77 1.59 2.12 2.39 3.19

• Pull gently on the water heater to ensure that it is properly mounted.

Figure 1 - Removing the Cover

Figure 2 - Water Heater Mounting Points

Figure 3 - DO NOT INSTALL UNIT UPSIDE DOWN Figure 4 - Inlet Pre-Filter

115 F

18 / 27kW Model 36kW Model

DO NOT INSTALL UNIT UPSIDE DOWN

OR ON ITS SIDE

18 / 27kW Model

36kW Model

Water

Pre-Filter

Water Pre-Filter

18 / 27kW Model

36kW Model

B. Plumbing

It is mandatory that all plumbing be done in accordance with federal, local, and

state plumbing codes and practices. Failure to properly install the water heater WILL

VOID the warranty. It is also necessary to use both thread tape and pipe dope on all

mechanical plumbing connections.

Install unions on the hot and cold water connections to easily disconnect the water

heater for servicing. See Figure 6.

• Connect the water inlet line to the entry point of the heater (right side inlet),

and connect the outlet line to the water outlet. Use a line that can withstand

a minimum pressure of 116 psi (8 bar). Using any other type of line will cause

damage. All water pipes within three (3) feet of the unit’s water inlet and outlet

must be rated for high temperature applications of 150

F (66

C) minimum.

Figure 5 - DO NOT

SOLDER TO THE UNIT

Do not solder any piping

to the unit’s connection

points.

• It is recommended to use exible water lines. See Figure 4.

• The maximum operating water pressure of this water heater is 150 psi / 10 bar. Residential plumbing

systems with unstable pressure or pressure above 73 psi require the application of a pressure stabilizer

valve, set to 58 - 73 psi.

• Do not install the appliance with water inlets and outlets at the top. See Figure 3.

• Before connecting pipes to the water heater, it is highly important to ush the lines to eliminate all residue

and debris from the inlet and outlet lines.

Do not apply heat to the Hot or Cold water heater connections. See Figure 5. If sweat connections are used,

sweat tubing to the adapter before tting adapter to the water connections on the heater. Any heat applied to

the water heater connections will permanently damage the water heater. Use two wrenches when tightening

water piping at heater. Use one wrench to prevent the heater inlet or outlet line from turning. Take care not to

over tighten. Damages due to improper installation practices ARE NOT covered by warranty.

Failure of the water heater due to lime scale build-up on the heating surface, low pH, or other imbalance IS NOT

covered by the warranty.

Figure 6 - Installation Detail

COLD WATER INLET

HOT WATER OUTLET

CHECK VALVE

BALL VALVE

AUTOMATIC WATER

SHUT-OFF VALVE

UNION

WATER LEAK

DETECTION

SENSOR

NOTES:

1. Minimum pipe size should

match connection size. Upsize

pipe accordingly if greater ow

is required.

2. Drains and check valve

between will assist in purging

air from system.

3. These drawings are meant

to demonstrate system piping

only. The installer is responsible

for all equipment and detailing

required by local codes. In

Massachusetts, you must install

a vacuum relief valve per 248

CMR.

4. A temperature and pressure

(T&P) relief valve is not required

for most installations, but may

be required to meet local,

state, or provincial codes. If

codes require a T&P valve,

install according to code and

manufacturer instructions.

5. Mixing valve applications are recommended to help prevent scalding.

6. It is highly recommended by the manufacturer to install water leak detection devices and automatic shuto valves in

any water heater installation where a leakage of water could result in property damages.

C. Temperature and Pressure Relief

This tankless water heater is equipped with both computer temperature control and mechanical auto resetting

high limit switches for high limit temperature protection. This product does not use a storage tank and a

temperature pressure relief valve (T&P) is not required for most installations. UL Standard 499 does NOT require

that a pressure relief valve be used.

However, a T&P valve may be required to meet installation codes in your area. If one is required, install the valve

in accordance with local codes. Ensure that it operates correctly and that air is purged from the valve before using

the water heater. When connecting to ex or high temperature CPVC pipe, it is recommended that a T&P valve

be used for added safety.

NOTE: Installations in the Commonwealth of Massachusetts and State of Kentucky require a pressure relief valve.

Please check local installation codes for any special requirements.

Do not thread a cap or plug into a relief valve or relief valve line under any circumstances! Explosion and

property damage, serious injury, or death may result.

An ASSE 1017 or ASSE 1070 temperature limiting or mixing valve is recommended in installations servicing

disabled or elderly persons, or children. Mixing valves do not eliminate the risk of scalding.

To avoid scalding:

• Set the water heater set point temperature as low as possible.

• Feel water before bathing or showering.

• If thermostatic valves are required, use devices specically designed for such purpose. Install these devices

in accordance with instructions provided by the manufacturer.

Failure to install a temperature limiting or mixing valve and follow these instructions could result in property

damage, severe personal injury, or death due to scalds.

D. Scalding

This water heater can deliver scalding water. Be careful whenever using hot water to avoid scalding injury. Certain

appliances such as dishwashers and automatic clothes washers may require increased water temperatures. By

setting the thermostat on this heater to obtain the increased water temperature required by these appliances

you may create the potential for scald injury.

To protect against injury, install a mixing valve in the water system. This valve will reduce point of use discharge

temperatures by mixing cold and hot water in branch supply lines. Such valves are available from your local

plumbing supplier.

E. Filling the Heater

• Make certain any drain valves in the system are completely closed.

• Open the shut-o valve in the cold water supply line.

• Open the hot water faucets to allow air to vent from the heater and

piping.

• Allow sucient time for the heater to completely ll with water.

• Check for and repair any leaks.

NOTE: If you detect a water leak from the water heater at this point, turn o

the water supply at the main shut-o valve and contact Customer Service.

When lling the water heater, open a hot water tap to release air in the

tank and piping. The tank must be full of water before the heater is turned

on. Failure to ensure the water heater is full before turning it on could

result in damage to the water heater and other property damages. Such

damages ARE NOT covered by water heater warranty.

Part 4 - Electrical Connection

Tank must be full of water before the power is turned on. The heating element will be damaged if energized for

even a short time while tank is dry. Failures due to “dry-ring” ARE NOT covered by warranty.

This water heater must be installed in accordance with all applicable local, state, provincial, and national electrical

codes. The heater must be connected to dedicated circuit breakers on the main electrical panel.

As with all electrical appliances, its crucial to rst shut o all power to the unit directly at the fuse or breaker box

before attempting to install or repair this water heater. Ensure that all breakers are shut.

Failure to disconnect the power from the water heater before attempting to install or repair it will result in

property damage, severe personal injury, or death.

All wiring (wire gauge) as well as circuit protection (breakers) must comply with the National Electrical Code

(NED) in the USA or the Canadian Electrical Code (CEC) in Canada, and should be done by a qualied licensed

electrician or the local electric utility. Failure to do so could result in property damage and/or personal injury

and void the product warranty.

Be sure to ground the water heater. Failure to do so could result in property damage, severe personal injury, or

death.

NOTE: In Canada, the CEC generally requires that all supply wires and corresponding circuit protection used for

domestic hot water heating and hydronic heating applications be sized to a minimum of 125% of the maximum

current rating of the heater (kindly check the heater specications below for details).

The voltage requirement and dedicated maximum amperage load for the heater is specied on the water

heater rating label. Consult your local power company to determine if your electrical service is adequate for the

additional load of the heater.

NOTE: 18 - 27kW models require 3 sets of wire and ground; 36kW models require 4 sets of wire and ground. See

Wiring Diagrams for additional information.

1. Take each wire pair and connect them to one breaker (see Wiring Diagrams). Ensure that each breaker

is connected to one black wire and one red wire. Ensure the power to the unit is shut o by means of the

dedicated circuit breakers in the main electrical panel.

2. A suitable wire gauge which meets all applicable electrical codes for the size of the breakers should be used.

The correct set of power cable wires should be run from the circuit breakers in the main electrical panel to the

water heater. Connect the power cable to the terminal block within the water heater.

3. Each incoming circuit requires a separate ground connector.

4. DOUBLE CHECK the electrical connections to ensure their correctness as well as the tightness and secureness

of wire connections. Its important to conrm that the correct breaker size and wire gauge has been used

Table 1 details the relationship of water temperature and time with regard

to scald injury and may be used as a guide in determining the safest water

temperature for your applications.

Figure 7 - Water Heater Wiring Diagrams

Wiring Diagram for 18 and 27kW

Terminal Block in Unit

L1 L2 L1 L2 L1 L2

L1 L2L1 L2L1 L2

8/2 AWG

240V

Unit Requires 8 - 10 AWG ground wire - one for each 240V circuit

L1 L2

L1 L2 L1 L2

240V

8/2 AWG

L1 L2

Wiring Diagram for 36kW

Terminal Block in Unit

L1 L2 L1 L2 L1 L2

and that the unit has

been connected to a

ground in accordance with

applicable codes.

• Ensure that all

connections are

correctly made

to ensure proper

operation of the unit. It

is critical that the unit

be wired as shown.

Mixing up one set of

wires with another will

result in the failure of

the unit to operate

correctly even though it

turns on and otherwise

appears to function

properly.

5. The front cover of the unit

should be replaced and

reattached with two (2)

screws.

6. Ensure that all the air has

been purged from the

water lines before turning

on power to the unit.

Kindly check STEP 3 in

the plumbing installation

section. Restore power to

the unit by means of the

dedicated circuit breakers

in the main electrical

panel.

Part 5 - Installation Checklist

Water Heater Location Yes No

Close to area of heated water demand

Indoors and protected from freezing temperatures

Area free of ammable vapors / combustibles

Provisions made to protect area from water damage

Sucient room to service heater

Relief Valve (If required by local, state, or provincial codes) Yes No

Temperature and Pressure Relief Valve properly installed and discharge line run to open drain

Discharge line protected from freezing

Wiring Yes No

Power supply voltage agrees with water heater rating plate

Branch circuit wire and fusing or circuit breaker of proper size

Electrical connections tight and unit properly grounded

Water Supply Yes No

Water heater completely lled with water BEFORE operating the unit

Air purged from water heater and piping

Water connections tight and free of leaks

Table 4 - Installation Checklist

Part 6 - Operation

The water heater must be full of water before the power is turned on. The heater will be damaged if energized

for even a short time while dry. Failures due to “dry-ring” ARE NOT covered by warranty.

This tankless electric water heater is designed to supply hot water instantaneously on demand. The unit contains

heating elements capable of heating water quickly for as long as necessary. Unlike a conventional tank storage

water heater, this tankless water heater does not store hot water. A tankless system is more ecient because it

does not waste energy continually heating water that is idly sitting and losing heat in a storage tank.

As soon as a demand for hot water is detected the heating elements are activated. Sensors continually monitor

water ow rate and incoming and outgoing temperature and transmit data to the system controller, which

determines the exact amount of power required by the heating elements to reach the set temperature.

Operating this tankless water heater is similar to using any traditional water heating system. However, it is very

important to carefully read all of the setup procedures and operating instructions in this manual to ensure the

maximum performance and energy savings from the water heater.

115 F

Figure 8 - User Interface Detail

A. User Interface / Controls

Power

• Press the button. The display will power on.

• Press again. The display will turn o.

Setting the Output Water Temperature

• To set the temperature, rst turn on a hot water faucet and allow water

to run through the heater. The digital display lights up and shows the current temperature setting.

• Press to increase or to decrease the temperature.

• Temperature can be set to any level from 86 - 122

F (30 - 50

C).

• A comfortable temperature for bathing and showering is between 105 and 110

F (41 and 43

C).

• The recommended temperature setting is 118

F (48

C), which will deliver hot water for all household needs

at a maximum water ow rate.

• A higher temperature setting is not recommended, as it can cause serious scalding injuries to children and

elderly persons. Higher temperatures also produce more scale buildup in water heating devices.

115 F

Figure 9 - Display and Inlet / Outlet Detail and Locations

B. Start-Up

1. Press the button to activate

the heater. The display will

show the outlet temperature.

2. With the water running

through the unit, press to

increase or to decrease

the outlet temperature. The

recommended temperature

setting is 118

F (48

C).

Do not attempt to repair this water heater yourself. Call a qualied service technician for assistance. Always

turn o the power supply to the heater prior to servicing or draining the heater. Failure to do so could result in

property damage, severe personal injury, or death.

Part 7 - Maintenance

For most of these maintenance operations, the water will have to be drained from the heater. For all of these

operations, the power should be turned o at the circuit breaker and the front cover removed.

The water heater has minimal required maintenance procedures. To ensure maximum performance of the water

heater and reduce the risk of a water leak:

• Periodic inspections and tests are always recommended for signs of damage or failure. Any damage,

cracks, leakage, or weakness should be addressed and xed immediately. Do not over-tighten any of the

connections. Over-tightening could cause serious internal damage to the unit.

• Water heated at higher temperatures produces scale buildup much faster than at lower temperatures.

Having manual shut-o/maintenance valves installed on the inlet and outlet of the water heater will allow

access to the unit. It is recommended to ush the unit once a year under normal conditions or once every six

months if the water supply has unusually hard water.

• Clean the pre-lter on the inlet water side once every six months. Wash lightly to remove any debris.

When any form of maintenance is carried out on the water heater or the home’s plumbing system that may

introduce air into the pipes, it is crucial to turn the power o to the water heater and purge the air out of the

lines before restoring power to the unit. Follow “Filling the Water Heater”, this manual. FAILURE TO DO SO COULD

RESULT IN PERMANENT DAMAGE TO THE HEATING ELEMENT AND VOID YOUR WARRANTY.

A. Removing the Cover

• Remove the four (4) Phillips screws, two (2) from each side of the water heater.

• The cover can be partially removed by gently pulling it from the assembly. Disconnect the wire harness from

the power control knob to fully remove the cover.

B. Draining the Heater

The water heater can be emptied by:

• Siphoning the water out through any lower service valve on the inlet side.

• Keep a hot water faucet open while siphoning the water out.

C. Removing a Heating Element

• Shut o the power supply and drain the water heater.

• Remove the front cover per the instructions above.

• Remove the three (3) Phillips screws securing the control box cover to the assembly. Carefully remove the

cover.

• Remove all of the wire harnesses connected to the control board.

• Disconnect the inlet and outlet plumbing adapters from the water heater.

• Use a pipe wrench to remove the two spacing nuts from the water heater inlet and outlet adapters.

• Remove the four (4) screws connecting the water heating assembly to the water heater cabinet.

• Remove the ve (5) screws connecting the wiring terminals to the water heater cabinet.

• Remove the entire water heating assembly.

• Use a screwdriver to remove all of the

screws connecting the wiring to the heating

element being inspected / replaced. See

Figure 10.

• Use a pipe wrench to remove the element

containing cap from the water heating

assembly.

• Remove the heating element.

D. Descaling the Heating Element

Scale deposits can aect the heating capability of the element. Heavy scale can even cause damage to the

element. The element can be descaled either chemically or manually.

• Soak the element in white vinegar or other food grade descaling solution approved for use in potable water

systems.

• Once descaled, rinse well with a fresh water / baking soda solution.

The element can also be descaled manually:

• After the element has dried, use a soft brush (non-metallic to prevent damaging th stainless steel sheath)

on the element.

• Brush the dried minerals o.

Reinstall the element after descaling. Ensure the element gasket is installed and that the element is rewired

correctly.

Ensure the water heater has been relled with water before restoring power. Failures due to “dry-ring” ARE NOT

covered by warranty.

Remove

wires

Remove

Heating

Element

Open Cover

Figure 10 - Removing an Element

Part 8 - Troubleshooting

Before calling for service check the troubleshooting list of common issues. This can save time and cost. If you are

unable to resolve a problem contact your installer or Customer Service for support.

Problem Possible Cause Solution

No hot water

and display

DOES NOT

power on

Power outage or faulty wiring

Check the power supply. Check the circuit breaker.

Ensure the breakers at main electrical panel are ON.

A breaker may be faulty or the unit may be wired

incorrectly.

Ensure the shuto valve on the unit’s incoming water

supply line is fully open.

The ow rate needed to activate

the heating element (0.5 gpm) has

not been reached.

Increase the ow rate from the water supply source.

Clean the lter screen on the unit’s water inlet.

No hot water

and display

DOES power

Reset the water heater.

Refer to this manual for reset points. Ensure all power

is shut o at the breaker panel before attempting to

reset the unit. Press all resets.

Potential internal part failure Call Customer Service.

Water Not Hot

Enough

Too much water owing through

the heater

Reduce the ow rate at the faucet or slightly close the

shuto valve on the unit’s incoming water supply line

to reduce ow rate

Voltage less than 240 volts

This water heater is designed to operate on 240 volts.

A lower voltage will produce less heating power. It

may be necessary to upgrade to a larger input heater.

Crossed wires Double check the wiring. Ensure it is correct.

Reduction in the ambient

temperature or temperature

setting is too low

Increase the temperature setting on the unit

Water pressure less than 7 psi

(0.5 bar)

Make sure the shuto valve is fully open and the

water supply line is not blocked

Mixing too much cold water

It is not necessary to mix as much cold water with a

tankless water heater as with a conventional storage

tank. Also, an anti-scald feature may be installed

on the faucet that is mixing cold water. These types

of features can usually be adjusted to reduce the

amount of cold water mixed.

Thermal loss due to long pipe run

As hot water runs through the system to the faucet,

some heat will be lost, especially if it has a long

distance to travel or the pipes are cold. This is normal

and can be compensated for by increasing the

temperature setting and insulating the pipes.

Electrical malfunction

Contact a qualied electrician or your local authorized

distributor for service

Water

Temperature

Varies from

Hot to Cold

During Use

Water pressure has dropped

below minimum level

Increase the ow rate from the water supply source

Problem Possible Cause Solution

Water Too Hot

Not enough water owing

through the heater

Increase the ow rate at the water outlet

Increase in the ambient

temperature or temperature

setting is too high

Switch to a lower temperature setting

Voltage less than 240 volts

This water heater is designed to operate on 240 volts.

A lower voltage will cause improper water heater

operation.

Water temperature at faucet too

hot

Check if ow is too low, set point temperature is too

high, or for internal part failure. If problem persists

contact Customer Service.

Heater Shuts

O During

Use

Power outage or faulty wiring

Check the power supply and circuit breaker. If

problem persists, contact a qualied electrician.

Water Stops

Flowing

Blockage in water pipes or hoses

Ensure the main water shuto valve is fully open and

there are no obstructions in the water supply line

No water supply

No Hot Water

with the

Unit’s Water

Supply Line

Shuto Valve

Fully Open

Power outage or faulty wiring Check the power supply and circuit breaker.

The ow rate needed to activate

the heating element (0.5 gpm) has

not been reached.

Increase the ow rate from the water supply source.

Clean the lter screen on the unit’s water inlet.

Table 5 - Troubleshooting

The risk of scald injury increases as you increase water temperature. A lower setting is more economical and

reduces the risk of scalding. Use a water tempering or mixing valve and extreme caution when using hot water

to avoid scald injury. Consult codes for conformance. Failure to follow the instructions in this warning statement

could result in serious personal injury or death from scalds.

Be sure to disconnect electrical power before performing service. Failure to do so could result in electrical shock,

property damage, serious personal injury, or death.

If draining of the water heater is necessary, open the T&P valve or a hot water tap to prevent vacuum buildup

in the tank and piping.

Occasionally, the high temperature limit shut o device may trip the resets. This occurs when water temperature

exceeds 185

F / 85

C. As with all electrical appliances, it is crucial to rst shut o all power to the unit directly at

the fuse or breaker box before attempting to reset this water heater. Ensure that all breakers are shut o.

Failure to disconnect the power from the water heater before attempting to install or repair it will result in

property damage, severe personal injury, or death.

A. Resetting the High Limit Switch

Locate the reset button locations as shown below and press both down. If the buttons “click” the unit has reset.

After the unit has reset, turn the breakers back on and observe unit operation.

Call a technician if the high limit needs to be reset frequently.

Figure 11 - High Limit Switch Reset Detail

18 / 27kW Model

36kW Model

B. Checking Thermostat Operation

To check thermostat operation:

• Press the button to activate the heater. The display will show the outlet temperature.

• With the water running through the unit, press to increase or to decrease the outlet temperature. The

recommended temperature setting is 118

F (48

C). NOTE: A lower setting is more economical and reduces

the risk of scalding.

C. Changing the Heating Element

• Turn o the power supply and drain the water heater (see

procedure, this manual).

• Remove heating element (see procedure, this manual).

• Install new element with new red O-Ring, making sure the

O-Ring and element are positioned correctly. Tighten the

retaining cap and wire connections. See Figure 12.

• Reinstall the water heating assembly. When reinstalling,

work in the opposite way of the procedure.

• Rell the water heater with water before restoring power.

D. Changing a Triac

• Turn o the power supply.

• Disconnect the three (3)

wire connectors on the

triac. Remove the wires.

See Figure 13.

• Remove the two (2)

screws connecting the

triac to the inlet. Remove

the triac.

• Install the new triac and

re-attach the wiring and

screws.

Insert

New

Heating

Element

Cover

Reconnect Wires

Insert New

Red O'Ring

Figure 12 - Installing an Element

Remove

Triac

Install

New Triac

Torque: 1.2Nm

Step 1

Step 3

Step 5

Step 2

Step 4

Step 6

Figure 13 - Changing a Triac

NOTE: After adjusting the water temperature, allow the heater

enough time to heat the water to temperature. Then use a

thermometer to measure the water temperature at a hot water

outlet in the structure.

Part 9 - Replacement Parts

Figure 14 - 18 - 27kW Replacement Parts

Table 6 - Replacement Part Numbers

Item

Description

Part #

Item

Description

Part #

Model Model

18 24 27 36 18 24 27 36

1 Front Cover 65118393 65118412 11 Heating Tank 65118403

2 Left Panel 65118394 12

Thermistor

(300mm)

65118404

3 Terminal Block 65118395 13 Flow Sensor 65118405

Terminal Block,

6 Poles

65118396 14 Triac 65153718

5 Back Cover 65118397 65118413 15 PCB Cover 65118406

6 Cable Bushing 65118398 16

Display

Support

65118416

Thermistor

(600mm)

65118399 17 Display 65118417

8 Thermostat 65118400 18 PCB (Main) 65118407 65118414

9 Gasket 65118401 19 Filter 65118408

Heating

Element

9kW 65118402 20 Right Panel 65118409

12 kw

13.5 kw 65118411

12 19

Figure 15 - 36kW Replacement Parts

Everlast Whole Home

Electric Tankless Water Heater

Limited Warranty

The manufacturer warrants each small capacity point of use

electric water heater and its components to be free from defects

in materials and workmanship according to the following terms,

conditions, and time periods. UNLESS OTHERWISE NOTED THESE

WARRANTIES COMMENCE ON THE DATE OF INSTALLATION. This

limited warranty is only available to the original consumer

purchaser (hereinafter “Owner”) of the water heater, and is non-

transferable.

WARRANTY PERIODS

Aures Pro InLine

Electric Water Heater

Parts Tank

Two (2) Years Six (6) Years

COVERAGE

A. During the rst two (2) years after the original date of

installation the manufacturer warrants that it will repair

or replace, at its option, any defective or malfunctioning

component of the water heater. Replacement components will

be warranted for ninety (90) days.

B. Should a defect or malfunction result in a leakage of water

from the water heater within the rst six (6) years after the

original date of installation due to defective material or

workmanship, malfunction, or failure to comply with the

above warranty, with such defect or malfunction having been

veried by an authorized representative of the manufacturer,

the manufacturer will repair or replace, at its option, the

defective or malfunctioning water heater. Replacements will

be of the nearest comparable model available at the time of

replacement. The replacement water heater will be warranted

for the unexpired portion of the applicable warranty period of

the original water heater.

C. In the event of a leakage of water of a replacement water

heater due to defective material or workmanship, malfunction,

or failure to comply with the above warranty, the manufacturer

reserves the right to refund to the Owner the published

wholesale price available at the date of manufacture of the

original water heater.

D. If government regulations, industry certication, or

similar standards require the replacement water heater or

component(s) to have features not found in the defective

water heater or component(s), the Owner will be charged the

dierence in price represented by those required features. If the

Owner pays the price dierence for those required features and/

or to upgrade the size and/or other features available on a new

replacement water heater or component(s), the Owner will also

receive a complete new limited warranty for that replacement

water heater or component(s).

E. If at the time of a request for service the Owner cannot provide

a copy of the original sales receipt or the warranty registration,

the warranty period for the water heater shall then be deemed

to have commenced on the date of manufacture of the water

heater and NOT the date of installation of the water heater, and

be covered by the unexpired portion of the warranty detailed

above.

F. This warranty extends only to water heaters utilized in

water heating applications that have been properly installed

by qualied professionals based upon the manufacturer’s

installation instructions.

G. It is expressly agreed between the manufacturer and the

Owner that repair, replacement, or refund are the exclusive

remedies of the Owner.

OWNER RESPONSIBILITIES

The Owner or Qualied Installer / Service Technician must:

1. Have a vacuum relief valve certied to ANSI Z21.22 - Relief

Valves for Hot Water Supply Systems - installed with the water

heater assembly in accordance with federal, state, and local

codes and in installations prone to vacuum related damages.

2. Maintain the water heater in accordance with the maintenance

procedure listed in the manufacturer’s provided instructions.

Preventive maintenance can help avoid any unnecessary

breakdown of the water heater and keep it running at optimum

eciency.

3. Maintain all related system components in good operating

condition.

4. Use the water heater at water pressures not exceeding the

working pressure shown on the rating plate.

5. Keep the water heater free of damaging scale deposits.

6. Make provisions so if the water heater or any component or

connection thereto should leak, the resulting ow of water will

not cause damage to the area in which it is installed.

WARRANTY EXCLUSIONS

This limited warranty will not cover:

1. Any water heater purchased from an unauthorized dealer.

2. Any water heater not installed by a qualied heating installer

/ service technician, or installations that do not conform to ANSI,

CSA, and/or UL standards, as well as any applicable national or

local building codes.

3. Service trips to teach the Owner how to install, use, maintain,

or to bring the water heater installation into compliance with

local building codes and regulations.

4. The workmanship of any installer. The manufacturer disclaims

and does not assume any liability of any nature caused by

improper installation, repair, or maintenance.

5. Electricity or fuel costs, or increased or unrealized savings for

same, for any reason whatsoever.

6. Any water damage arising, directly or indirectly, from any

defect in the water heater or component part(s) or from its use.

7. Any incidental, consequential, special, or contingent damages

or expenses arising, directly or indirectly, from any defect in the

water heater or the use of the water heater.

8. Failure to locate the water heater in an area where leakage

of the tank or water line connections and the relief valve will

not result in damage to the area adjacent to the water heater

or lower oors of the structure, as well as failure to install the

water heater in or with a properly sized drain pan routed to an

approved drainage location.

9. Any failed components of the system not manufactured by

the manufacturer as part of the water heater.

10. Water heaters repaired or altered without the prior written

approval of the manufacturer.

11. Damages, malfunctions, or failures resulting from improper

installation, or failure to install the water heater in accordance

with applicable building codes/ordinances or good plumbing

and electrical trade practices; or failure to operate and maintain

the water heater in accordance with the manufacturer’s

provided instructions.

12. Damages, malfunctions, or failures resulting from failure

to operate the water heater at pressures not exceeding the

working pressure shown on the rating label.

13. Failure or performance problems caused by improper sizing

of the water heater, expansion device, piping, electric service

voltage, wiring or fusing.

14. Damages, malfunctions, or failures resulting from vacuum

conditions.

15. Damages, malfunctions, or failures caused by operating

the water heater with modied, altered, or unapproved

components, or any component / attachment not supplied by

the manufacturer.

16. Damages, malfunctions, or failures caused by abuse,

accident, re, ood, freeze, lightning, electrochemical reaction,

acts of God and the like.

17. Tank failures (leaks) caused by operating the water heater in

a corrosive or contaminated atmosphere.

18. Damages, malfunctions, or failures caused by operating the

water heater with an empty or partially empty tank (“dry ring”),

or failures caused by operating the water heater when it is not

supplied with potable water, free to circulate at all times.

19. Failure of the heater due to the accumulation of solid

materials or lime deposits.

20. Any damage or failure resulting from improper water

chemistry, or heating anything other than potable water. WATER

CHEMISTRY REQUIREMENTS - Water pH between 6.5 and 8.5.

Hardness less than 7 grains (120 mg/L). Chloride concentration

less than 100 ppm (mg/L). TDS less than 500 ppm (mg/L).

21. Production of noise, taste, odors, discoloration, or rusty

water.

22. Water heaters replaced for cosmetic reasons.

23. Components of the water heater that are not defective,

but must be replaced during the warranty period as a result of

reasonable wear and tear.

24. Components of the water heater that are subject

to warranties, if any, given by their manufacturers; the

manufacturer does not adopt these warranties.

25. Damages, malfunctions, or failures resulting from the use of

any attachment(s) not supplied by the manufacturer.

26. Water heaters installed outside the fty states (and the

District of Columbia) of the United States of America and

Canada.

27. Water heaters moved from the original installation location.

28. Water heaters that have had their rating labels removed.

PROCEDURES FOR WARRANTY SERVICE REQUESTS

Any claim for warranty assistance must be made promptly.

Determine if the water heater is “in-warranty” (that is, within the

applicable warranty period) by reviewing a copy of the original

sales receipt or warranty registration. The Owner must present

a copy of the original sales receipt or warranty registration for a

warranty service request.

If the water heater is “in-warranty”, contact the retailer from

whom the water heater was purchased (or the installer) for

assistance. Be prepared to provide the retailer or installer with a

copy of the original receipt, complete model and serial numbers,

and the date of installation of the water heater, in addition to

explanation of the water heater problem.

Warranty coverage is subject to validation of “in-warranty”

coverage by the manufacturer claims department personnel.

All alleged defective or malfunctioning components must be

returned to the manufacturer via the local distribution channels

where original purchase was made. NOTE: Any components or

heaters returned to the manufacturer for warranty analysis

will become the property of the manufacturer and will not

be returned, even if credit is denied. If all warranty conditions

are satised, the manufacturer will provide replacement

components to the retailer.

For questions about the coverage of this warranty, please

contact the manufacturer at the following address or phone

number: HTP (an Ariston Thermo Group Company), 272

Duchaine Blvd, New Bedford, MA, 02745 Attention: Warranty

Service Department, 1 (774) 271 3108.

SERVICE, LABOR, AND SHIPPING COSTS

Except when specically prohibited by the applicable state law,

the Owner, and not the Manufacturer, shall be liable for and

shall pay for all charges for labor or other expenses incurred

in the removal, repair, or replacement of the appliance or any

component part(s) claimed to be defective or any expense

incurred to remedy any defect in the product. Such charges

include, but are not necessarily limited to:

1. All freight, shipping, handling, and delivery costs of

forwarding a new appliance or replacement part(s) to the

owner.

2. All costs necessary or incidental in removing the defective

appliance or component part(s) and installing a new appliance

or replacement part(s).

3. All administrative fees incurred by the Owner, as well as

material required to complete, and/or permits required for,

installation of a new appliance or replacement part(s), and

4. All costs necessary or incidental in returning the defective

water heater or component part(s) to a location designated by

the manufacturer.

LIMITATIONS OF YOUR WARRANTY AND REMEDIES

THE FOREGOING WARRANTIES ARE EXCLUSIVE AND ARE GIVEN

AND ACCEPTED TO THE FURTHEST EXTENT UNDER APPLICABLE

LAW IN LIEU OF ANY AND ALL OTHER WARRANTIES, EXPRESS

OR IMPLIED, INCLUDING WITHOUT LIMITATION THE IMPLIED

WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A

PARTICULAR PURPOSE AND ANY OBLIGATION, LIABILITY,

RIGHT, CLAIM OR REMEDY IN CONTRACT OR TORT, WHETHER

OR NOT ARISING FROM THE MANUFACTURER’s NEGLIGENCE,

ACTUAL OR IMPUTED. THE REMEDIES OF THE OWNER SHALL

BE LIMITED TO THOSE PROVIDED HEREIN TO THE EXCLUSION

OF ANY OTHER REMEDIES INCLUDING WITHOUT LIMITATION,

INCIDENTAL OR CONSEQUENTIAL DAMAGES, SAID INCIDENTAL

AND CONSEQUENTIAL DAMAGES INCLUDING, BUT NOT LIMITED

TO, PROPERTY DAMAGE, LOST PROFIT OR DAMAGES ALLEGED TO

HAVE BEEN CAUSED BY ANY FAILURE OF THE MANUFACTURER

TO MEET ANY OBLIGATION UNDER THIS AGREEMENT INCLUDING

THE OBLIGATION TO REPAIR AND REPLACE SET FORTH ABOVE.

NO AGREEMENT VARYING OR EXTENDING THE FOREGOING

WARRANTIES, REMEDIES OR THIS LIMITATION WILL BE BINDING

UPON THE MANUFACTURER. UNLESS IN WRITING AND SIGNED

BY A DULY AUTHORIZED OFFICER OF THE MANUFACTURER. THE

WARRANTIES STATED HEREIN ARE NOT TRANSFERABLE AND

SHALL BE FOR THE BENEFIT OF THE OWNER ONLY.

NO OTHER WARRANTIES

This warranty gives the Owner specic legal rights. The Owner may

also have other rights that vary from state to state. Some states do

not allow the exclusion or limitation of incidental or consequential

damages so this limitation or exclusion may not apply to the Owner.

These are the only written warranties applicable to the water heater

manufactured and sold by the manufacturer. The manufacturer

neither assumes nor authorizes anyone to assume for it any other

obligation or liability in connection with said water heaters.

The manufacturer reserves the right to change specications or

discontinue models without notice.

Customer Installation Record Form

The following form should be completed by the qualied installer / service technician for you to keep as a

record of the installation in case of a warranty claim. After reading the important notes at the bottom of the

page, please also sign this document.

Customer’s Name

Date of Installation

Installation Address

Product Model / Serial

Number(s)

Comments

Installer’s Code / Name

Installers Phone Number

Signed by Installer

Signed by Customer

Installation Notes

IMPORTANT

Customer: Please only sign after the qualied installer / service technician has fully reviewed the installation,

safety, proper operation, and maintenance of the system. If the system has any problems please call the qualied

installer / service technician. If you are unable to make contact, please call your sales representative.

Distributor / Dealer: Please insert contact details.

La page charge ...

Ariston AURES PRO 36 240V US Manuel utilisateur

Marque: Ariston

Modèle: AURES PRO 36 240V US

Catégorie: Chauffe-eau

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Ariston AURES PRO 36 240V US User manual
español: Ariston AURES PRO 36 240V US Manual de usuario

Ariston AURES PRO 36 240V US Manuel utilisateur

Ariston AURES PRO 36 240V US Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents