BLACK+DECKER BD-11-DWH Manuel utilisateur

www.bdwaterheaters.com

Electric Tankless Water Heaters

Model

BD-36-DWH

118

º

F

temp

2

Important Safety Guideline

THIS INSTRUCTION MANUAL SHOULD BE SAVED FOR FUTURE REFERENCE.

Denitions: Safety Alert Symbols and Words

This instruction manual uses the following safety alert symbols and words to alert you to hazardous

situations and your risk of personal injury or property damage.

DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in

death or serious injury.

WARNING: Indicates a potentially hazardous situation which, if not avoided, could result

in death or serious injury.

CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in

minor or moderate injury.

(Used without word) Indicates a safety related message.

NOTICE: Indicates a practice not related to personal injury which, if not avoided, may

result in property damage.

WARNING: PLEASE READ THIS INSTRUCTION MANUAL THOROUGHLY AND COMPLETELY

BEFORE INSTALLATION & USE. FAILURE TO DO SO COULD CAUSE DAMAGE TO PROPERTY,

SERIOUS INJURY OR DEATH, AND VOID YOUR WARRANTY.

Please contact us directly, should you have any questions regarding your unit. We are available

Monday- Friday, 9AM-5PM EST at:

Phone: 1-844-746-6688

Email: [email protected]

For California residents / Pour les résidents de la Californie / Para residentes en California

WARNING: Cancer and Reproductive Harm -

www.P65Warnings.ca.gov.

AVERTISSEMENT: Cancer et Troubles de l'appareil reproducteur -

www.P65Warnings.ca.gov.

ADVERTENCIA: Cáncer y Daño Reproductivo -

www.P65Warnings.ca.gov.

3

Table of Contents

1. Safety Guidelines ------------------------------------------------------------------------------------04

2. About Your Black+ Decker Electric Tankless Water Heater ---------------------------------04-05

3. Selecting an Installation location -------------------------------------------------------------------05

4. Mounting Your Water Heater -------------------------------------------------------------------06-07

5. Plumbing Requirements and Precautions -----------------------------------------------------07-08

6. Plumbing Installation --------------------------------------------------------------------------------08

7. Electrical Requirements and Precautions ---------------------------------------------------------09

8. Electrical Installation ----------------------------------------------------------------------------- 10-11

9. Flow Rate -------------------------------------------------------------------------------------------- 12

10. Operation Guide ---------------------------------------------------------------------------------12-13

11. Care and Maintenance --------------------------------------------------------------------------13-14

12. User Interface/Controls -------------------------------------------------------------------------14-15

13. Troubleshooting ----------------------------------------------------------------------------------16-17

14. Reset Unit --------------------------------------------------------------------------------------------18

Before Installing

By installing this product, you acknowledge the terms of the manufacturer’s warranty and

authorized dealer’s return policy. Once the heater is installed, do not return the product to the

place of purchase. If you have any questions regarding the warranty or the product return policies,

please contact us by phone or email.

4

1. Safety Guidelines

Please read this manual thoroughly before installing & using the instant water heater. Failure

to comply with the safety, installation or operating instructions will void the product warranty.

Manufacturer and distributor of the product will not be liable for any damage or injury caused

by the failure to comply with the installation and operating instructions specied in this manual

or the improper use of the product. Ensure that this product is installed in accordance with the

national, state or local electrical and plumbing codes applicable to your area, and as specied in

our instructional guide to get the best performance from your Instant Water Heater.

This product has more than one power connection source. Do not attempt to install, clean, inspect,

disassemble, service or repair the water heater without shutting o all the power sources to the

unit on the main electrical panel using the circuit breaker.

WARNING: Failure to adhere might result in severe injury or death. The water heater must

be installed in compliance with all national, state, provincial and local electrical and building

regulations. We recommend that you consult a qualied electrician and a qualied plumber if

you have questions about anything relating to codes or regulations for this product.

This product is intended for household and indoor use only. Do not immerse in water.

The breaker used to power this unit must be grounded by means of the electrical panel.

The heater must be directly connected to dedicated circuit breakers on the main electrical

panel.

Do not install the heater where it may be subjected to direct sunlight, rain, splashing water,

moisture/humidity or freezing temperatures.

This unit is intended for heating water only. Do not attempt to use the unit for heating any

other kind of liquid.

2. About Your Black+ Decker Electric Tankless Water Heater

Congratulations on making the decision to purchase one of the best and nest Instant Water

Heaters currently available in the market today! Your new Instant Water Heater features advanced

water ow rate and temperature sensors which are designed to modulate power to the heating

elements to maintain a user-selected output water temperature range for 36 KW: 86°F (30°C) to

140°F (60°C) (subject to the temperature of the incoming water).

WARNING: When selecting the water temperature setting of your Instant Water Heater’s

thermostat, factors such as safety and energy conservation should be considered. Continuous

exposure of the skin to water temperatures above 120°F (49°C) can result in severe burns or

death. The maximum temperature to be set on this Instant Water Heater’s thermostat is 140°F

(60°C). Always take precaution to feel the water before bathing or showering to make sure the

temperatures are not too hot. You are required to read and comply with the Time/Temperature

Relationship Chart on the following page to determine the right water temperature for your home.

5

Time/Temperature

Relationship in Scalds

120°F (49°C)

Exposure for more than 5 minutes

122°F (50°C) Around 3 minutes of exposure

You may require a 120°F (49°C) or lower thermostat setting

to prevent contact with “HOT” water, if you have small children,

disabled, or elderly persons in your home. The temperature of the

water is regulated by the electronic control on the front of the water

heater.

3. Selecting an Installation Location

• This Water Heater is designed for indoor installation only.

• It should not be installed in a location where it might be

subjected to freezing temperatures as the freezing of the water

in the Water Heater can lead to severe and irreversible damages which are not covered under

your warranty.

• The Water Heater should not be placed in a location that is dicult to access.

•

Ensure that the water heater, as well as the power supplies and water connections, are

out of reach of children as the outlet water pipe can get very hot and touching can lead to

injury.

• Avoid installing your tankless water heater in a location prone to excessive humidity, moisture,

or dust, or in an area where it may be splashed with water or other liquids. DO NOT install

underwater pipes or air conditioning lines that might leak or condense moisture that could

then drip onto the heater. DO NOT install above electrical boxes or junctions.

• Do not install in areas which can be damaged due to leakage from the Water Heater. However,

safety measure such as suitable drip pan or an active water leak detector and shuto valve

should be installed in such areas that cannot be avoided.

Item # Unit dimensions (inches) Weight (lbs) Connections

BD-36-DWH 23.23 x 4.53 x 14.77 16.23 3/4”

WARNING: Water heaters are heat producing appliances. In order to avoid damage, injury or

death, there shall be no materials stored against the water heater and proper care shall be

taken to prevent unnecessary contact (especially by children) with the water heater. UNDER

NO CIRCUMSTANCES SHALL FLAMMABLE MATERIALS, SUCH AS GASOLINE OR PAINT

THINNER BE USED OR STORED IN THE VICINITY OF THIS WATER HEATER OR ANY

LOCATION FROM WHICH FUMES COULD REACH THE WATER HEATER.

•Children,disabledand

elderlyareathighriskof

beingscalded.

•Seeinstructionmanual

beforesettingyourdesired

hotwatertemperature

•Alwaysfeelwaterbefore

bathingorshowering

6

4. Mounting Your Water Heater

1. Your tankless water heater should be secured to a solid mounting surface with four screws,

(minimum 1” (25.4mm) long).

2. Ensure that the unit is level before fastening the screws in place.

3. The unit must be installed in an upright position with the water inlet and outlet at the bottom

of the unit. Do not install inversely with connections facing up or sideways with connections

facing right or left.

4. Do not install the unit above electrical boxes or junctions.

5. The water heater must be installed in a manner that prevents contact with ammable liquids

and gases. Keep these ammable materials at least two feet away from the heater and the

hot water outlet pipe. The water heater and the hot water outlet pipe must be secured, and

out of children’s reach to prevent tampering with controls or contact with an extremely hot

pipe.

6. If installing the heater on an upper oor or attic, make sure installation complies with the local

codes. Install a drip pan with drainage, or a leak detector and automatic shuto valve, to

prevent damage in case of any leakage.

a. Remove the appliance cover. (Heater cover) (gure 3)

b. Mount the unit on the wall with 4 screws at the marked points (gure 4)

c. Make sure the unit is leveled horizontally, with water inlets and outlets at the bottom

(g.5)

Fig. 3 Fig. 4

Fig. 5

Do not install upside down

or on its side

Fig. 6

Water

Pre-Filter

118

º

F

temp

7

Recommended clearances: 12” (304.8mm) above and below the heater

6” (152.4mm) in front of and to the sides of the heater

CAUTION: Please keep any ammable materials at least 24” (609.6mm) away from the water

heater and hot water outlet pipe.

5. Plumbing Requirements and Precautions

• Please follow all plumbing instructions carefully. This product must be installed in accordance

with all national, state, provincial, and local plumbing codes. We recommend consulting with

your municipality or a qualied plumber if you have questions relating to plumbing codes for

your area prior to installing.

• The plumbing installation must be completed before the electrical installation.

• DO NOT solder any pipe with the unit connected to the pipe. The

heat from soldering may cause damage to the ow sensor. Doing so

will void the warranty.

• The use of a temperature pressure relief valve (T&P) is not required for

most installations because the tankless water heater does not use a

storage tank. UL Standard 499 does not require that a pressure relief

valve is used, although it may be needed to meet installation codes in

your area. In such cases, the pressure relief valve should be installed

in accordance with local codes. It is important to ensure that the unit

is operating correctly, and that air is purged from the valve prior to installing the water heater.

• A T&P valve is recommended for added safety when connecting to plumbing rated Metal,

Flex or High-Temperature CPVC piping.

NOTE: A pressure relief valve is required for installations in the Commonwealth of

Massachusetts and State of Kentucky. Please check your local installation codes

for any special requirements.

• The plumbing installation requires piping that can withstand pressure up to 8 BAR.

• The maximum operating water pressure for this unit is 150PSI / 10BAR. Residential plumbing

systems with unstable pressure or pressure above 5 BAR require the application of a pressure

reduction valve set to 4-5 BAR for optimal performance.

• The water supply ow rate must be at least 0.5 Gallons per Minute (GPM) to ensure proper

operation.

• Flexible water hoses are recommended to be used with your water heater when installing

your water heater. When connecting the inlet water pipe to the unit, use a wrench to hold the

unit’s connection, and another wrench to tighten so that the ow sensor on the unit will not

be loosened or damaged. Do not over-tighten the water inlet and outlet connections to avoid

severe internal damage to the water heater.

Fig. 7

Do not solder any

piping to the unit’s

Connection points

8

• We recommend the installation of a manual shut-o valve (ball valve) on the inlet and outlet

of the water heater to create a convenient shut-o point if future maintenance or servicing

is required. Before connecting the pipes to the water heater, it is highly essential to ush

the lines to eliminate all the plumbing paste or residue in the lines caused by any welding or

soldering.

• All the water pipes within 3 feet (1 meter) of the inlet and outlet connections are recommended

to be rated for high-temperature applications with 150°F (66°C) minimum.

• Before proceeding to the electrical installation, run water through the unit for several minutes

to ush out any air bubbles from the water line.

6. Plumbing Installation

STEP 1: Thoroughly ush cold supply line of debris.

STEP 2: Connect the HOT WATER line to the water heater OUTLET. The water heater outlet can

be seen on the left side of the heater when facing the unit. Connect the COLD-WATER line to the

water heater marked COLD WATER INLET which is located on the right side when facing the unit.

* Pre-heated water can be connected to the cold water inlet, where this unit will act as a booster.

STEP 3: After tightening both ttings at the water heater, several hot water faucets should be

opened to allow the ow of water through the water heater for at least 2 to 3 minutes. This process

purges all the air from the water lines and MUST be performed before turning on the power at the

unit.

FAILURE TO FOLLOW THIS STEP MIGHT CAUSE PERMANENT DAMAGE TO THE HEATING

ELEMENTS. (The power to the heater should be turned o and the air purged out of the lines

before turning the power on anytime maintenance is performed on the water heater or the homes

plumbing system, as air might have been introduced into the plumbing pipes.)

STEP 4: Carefully inspect all connections, units, and the pressure relief device for leaks after the

plumbing installation is completed. If there are no leaks present, you can proceed to the electrical

installation.

CAUTION: If you detect a water leak from the water heater at this point, turn o the water

supply at the shut o valve on the unit’s incoming water supply and contact us at 1-844-746-6688.

Plumbing Specications

Minimum water ow to activate the unit 0.5 gpm

Working pressure 0.5–10 BAR (7–150 psi)

Tested pressure (maximum) 20 BAR (290 psi)

Water connections 3/4” NPT

9

7. Electrical Requirements and Precautions

Manufacturer recommends that this product be installed in accordance with all applicable national,

state, provincial, and local electrical codes. Consult a qualied and licensed electrician if you have

questions or are unsure about anything relating to codes for this product. The heater must be

connected to a dedicated circuit breaker on the main electrical panel.

WARNING: As with all electrical appliances, it’s crucial to rst shut o all power to the unit

directly at the fuse or breaker box before attempting to install, repair or disassemble this water

heater. Ensure that the breaker is shut o. SERIOUS BODILY INJURY OR DEATH COULD OCCUR

IF YOU IGNORE THIS WARNING.

CAUTION: All wiring (wire gauge), as well as circuit protection (breaker), must comply with

the U.S. National Electrical Code (NEC) in the USA or the Canadian Electrical Code (CEC) in

Canada. Failure to do so could lead to property damage, personal injury, and void your warranty.

Note: The Canadian Electrical Code generally requires that all supply wires and corresponding

circuit protection used for domestic hot water heating and hydronic heating applications be sized

to a minimum of 125% of the maximum current rating of the heater (check heater specication

details below).

Before installing this tankless water heater, ensure that sucient electrical power is available

in the home to handle the maximum amperage load of the applicable heater.

IMPORTANT NOTES:

36kW heater requires 3 set of wire and ground (see wiring diagram on page 11)

• Please see electrical specications by heater input and wiring diagram on the page 11 for

additional electrical information.

10

8. Electrical Installation

STEP 1: Take the wire pair and connect to the breaker (see wiring diagram). Be sure that the

breaker is connected to one black wire and one red wire. Be sure the power to the unit is shut o

using the dedicated circuit breakers in the main electrical panel.

STEP 2: Run the correct set of power cable wires from the circuit breaker in the main electrical

panel to the water heater by utilizing a suitable wire gauge which meets all applicable electrical

codes for the size of the breaker. Then, connect the power cable to the block terminal within the

water heater.

STEP 3: Unit requires a ground conductor for the incoming circuit.

STEP 4:

DOUBLE CHECK the electrical connections and ensure the wire connections are

correct, tight and secure. It’s important to conrm that the right breaker size and wire gauge has

been used and that the unit has been connected to a ground in accordance with applicable codes.

Be sure to reattach the front cover of the unit with two screws.

STEP 5: Ensure that all the air has been purged from the water lines before turning on power to

the unit. Refer to STEP 3 in the plumbing installation section. Restore power to the unit through

the dedicated circuit breaker in the main electrical panel.

It is crucial to follow the wire connection as shown and ensure all connections are made

correctly for proper operation of the unit. The unit will not operate correctly, even though it

turns on and otherwise appears to function, if you mix up one set of wire with another.

11

Electrical Specications by Heater Input

Item # kW Max

Amps

Required Breaker Req. Wire Size

BD-36-DWH 36 150 4 x 40A Double Pole 4 x 8/2 AWG with Ground

Power Rates

Item # 240V 220V 208V

BD-36-DWH 36,000 Watts 30,250 Watts 27,040 Watts

Your tankless water heater is now installed and ready to use! Follow the General Operating

Instructions to complete the setup.

Wiring Diagram for BD-36-DWH

Unit Requires 10 AWG ground wire - one for each 240V circuit

Terminal Block in Unit

L1L1L1 L2

8/2 AWG

L2L2

240V

L1 L2 L1 L2 L1 L2

L1 L2

240V

L1 L2

8/2 AWG

12

9. Flow Rate

The chart below indicates maximum temperature rise for a given ow rate

INLET GROUND WATER TEMP

Item # kW 30°F 40°F 50°F 60°F 70°F

BD-36-DWH 36 6.2 5.15 4.4 3.9 3.1

Based on 105°F Output Water Temp

10. Operation Guide

Operating your new tankless water heater is similar to using any traditional water heating system.

However, it is essential that you carefully read all setup procedures, operating instructions and

tips to ensure the maximum performance and energy savings from your new water heater. We

recommend that all members of the household read these General Operating Instructions.

This electric water heater is designed to supply hot water. The unit contains heating elements within,

capable of heating water quickly on-demand for as long as you need it. Unlike a conventional tank

storage water heater, this unit is a tankless water heater that does not store hot water. However,

once you begin using the system, you will understand it works like a conventional tank system.

Tankless system delivers hot water instantaneously on demand. Since a tankless system does not

waste energy continually when heating water, i.e. idly sitting and losing heat in a storage tank, it

provides signicant energy savings than a conventional water heater.

With your new system, as soon as you turn on the hot water faucet, the demand for hot water is

detected by a ow sensor, and the high-power heating elements are activated. Sensors continually

monitor the water ow rate and measured the incoming and outgoing water temperature. Data is

transmitted to the system logic controls, which determines the exact amount of power required by

heating elements to heat the water to your desired temperature.

It is essential to keep in mind that all tankless water heaters are subject to a maximum ow rate. If

this ow rate is exceeded, the heater will not be capable of suciently heating water.

Also keep in mind that conventional tank heaters are set to high temperatures to prevent running

out of hot water quickly, and thus a large amount of cold water needs to be mixed in to reach a

comfortable level for washing and showering. Since this unit heats water on demand, it is designed

to heat to a lower temperature. This means you only need to mix in a small amount of cold water

or none at all.

Your hot water supply may also be aected by the incoming water temperatures as the season

diers. During winter, if the incoming water temperature is frigid, you might not be able to run

multiple hot water outlets at the same time as compared to the summer. However, you can run

showers back-to-back without having to wait for the water to heat.

Water Quality: One of the things which should be taken into consideration when installing and

maintaining the water heater is the quality of water. Water conditions outside the recommended

levels outlined below are not permitted and can damage the water heater. We reserve the right to

deny any warranty claim regarding damage suered due to use in water conditions that are not

13

in accordance with the table below. The water must be treated, and the heater ushed regularly

when this product is installed in an area that is known to have hard water that causes scale build-

up to prevent damage to the heat exchanger and heating elements. We recommend that a water

treatment device or water softener should be installed to maintain optimal performance of the

water heater in hard water areas.

Chart for Recommended Water Quality levels

pH Total

Dissolved

Solid (TDS)

Free

CO2

Total

Hardness

Aluminum Chloride Copper Iron Manganese Zinc

6.5

-

8.5

Up to

500

mg/L

Up to

500

mg/L

Up to

200

mg/L

Up to

0.2

mg/L

Up to

250

mg/L

Up to

1.0

mg/L

Up to

0.3

mg/L

Up to

0.05

mg/L

Up

to 5

mg/L

11. Care and Maintenance

To ensure maximum performance of your water heater and to reduce the risk of a water leak, we

recommend the following maintenance:

• The water heater has minimally required maintenance procedures. Periodic inspections and

tests are always recommended for signs of damage or failure. Any damage, cracks, leakage

or weakness should be addressed and xed immediately. Do not over tighten any of the

connections. Over tightening the connection points could cause severe internal damage to

the unit.

• Remember that water heated at higher temperatures produces scale buildup much faster

than at lower temperatures. Having manual shut-o/maintenance valves installed on the inlet

and outlet of the water heater will allow access to ush the unit with a descaling solution. We

recommend routine maintenance once a year or once every six months if the water supply

has an unusually high level of mineralization (hard water)

• Clean the pre-lter on the inlet water side once every six months. Wash lightly to remove any

debris.

When any form of maintenance is carried out on the water heater or the home’s plumbing system

that may introduce air into the plumbing pipes, it is crucial to power o the water heater and purge

the air out of the lines before allowing the unit to power up.

FAILURE TO DO SO COULD RESULT IN PERMANENT DAMAGE TO THE HEATING ELEMENT

AND VOID YOUR WARRANTY.

When air is introduced into the plumbing system, follow the steps below to ensure the unit can

safely resume operation.

1. Shut o all power connections to the unit at the circuit breaker on the main electrical panel.

2. Perform the maintenance or servicing tasks.

3. Open one or more hot water faucets and allow water to run through the unit for several

14

minutes to purge any air from the heater and water lines.

This step must be performed before turning on power to the heater. Failure to complete

this step may cause permanent damage to the heating elements.

4. Reconnect power to the unit at the circuit breaker on the main electrical panel. Press and

switch the ON position.

5. With the water running through the unit, check and reset the temperature if necessary. The

recommended temperature setting is 118°F (48°C).

12. User Interface/Controls

Power

• Press

button, the display will turn on

• Press

button again, the display will turn o

Setting the Output Water Temperature

• To set the temperature, rst turn on a hot water

faucet and allow water to run through the heater.

The digital display lights up and shows the

current temperature setting.

• To increase or lower the temperature setting,

press

increase the temperature or to

decrease the temperature.

• Temperature can be set to any temperature from

86°F (30°C) to 140°F (60°C).

• A comfortable temperature for bathing and showering is between 105°F (41°C) and 110°F

(43°C).

• The recommended temperature setting is 118°F (48°C), which will deliver hot water for all

household needs at a maximum water ow rate.

CAUTION: A higher temperature setting is not recommended, as it can cause severe

scalding injuries to children and elderly persons. Higher temperatures also produce more

scale buildup in water heating devices.

118

º

F

temp

Press button to raise the

temperature (up to 140°F / 60°C)

or Press button to lower the

temperature (as low as 86°F / 30°C)

15

118

º

F

temp

Starting the system for the rst time

1. Press

button, to activate the heater to display outlet temperature.

2. With the water running through the unit, press

or to adjust the temperature.

Freezing Temperatures

If the ambient temperature falls below 32°F (0°C), protect the heater from potential damage. Power

o the unit using the dedicated circuit breaker on the main electrical panel. Open a faucet slightly

to cause water to ow continuously through the device at a very low rate, without heating. Restore

power to the unit when temperature condition is normal.

If the water inside the heater freezes, it can cause damage that is not covered by warranty. If

you suspect water has frozen within the unit, do not turn it on until you are sure the frozen water

has melted, and there are no leaks in the unit. It is recommended to contact a qualied electrician

or the manufacturer for service in this situation.

Digital temperature display

Temperature setting Buttons

Power Button

Cold water inlet

Hot water outlet

(to be connected to the main hot water pipe)

16

13. Troubleshooting

Before calling for service, check the troubleshooting list of common issues.

If you are unable to resolve a problem, contact your locally authorized distributor.

PROBLEM

ISSUE

POSSIBLE CAUSE SOLUTION

No hot

water and

display do

NOT light up

Power outage or

faulty wiring.

Check the power supply. Check the circuit breakers.

Make sure the breakers at main electrical panel are ON.

You may have a faulty breaker or unit may be wired

incorrectly.

Make sure the shuto valve on the unit’s incoming water

supply line is fully open.

The ow rate needed

to activate the heating

element (0.5 gpm) has

not been reached.

Increase the ow rate from the water supply source.

Clean the lter screen on the unit’s water inlet.

No hot

water and

display

DOES light

up

Reset the unit Refer to manual (Page 18) for diagram of reset points.

Make sure to shut all power on your breaker panel

before attempting to reset unit. All resets must be

pressed.

Potential internal part

failure

Please call us for further technical assistance.

Water is

heated,

but not hot

enough.

The water ow rate

exceeds the heating

capacity of the heater.

Reduce the water ow rate at the faucet or slightly close

the shuto valve on the unit’s incoming water supply line

to reduce the water ow rate.

Voltage less than 240

Volts

The heating elements on your water heater are designed

for 240 volts. When used with a lower voltage, they

produce less heating power. You may need to upgrade

to a larger input heater.

Crossed Wires. If it’s a new installation, double check the wiring to

conrm that it is correct.

Temperature setting is

too low.

Increase the temperature setting on the unit.

Water pressure is less

than 0.5 BAR (7 psi).

Make sure the shuto valve is fully open, and the water

supply line is not blocked.

Mixing too much cold

water

You do not need to mix as much cold water with your

tankless water heater compared to when you use a

conventional water heater. You may also have an anti-

scald feature on your faucet that is mixing cold water.

These types of faucets can usually be adjusted to reduce

the amount of cold water mixed.

Thermal loss due to

long pipe run.

As the hot water from the heater runs through the hot

water delivery system to your faucet, some heat will be

lost especially if it has long distance to travel or the pipes

are cold. This is normal. You can compensate for this by

increasing the setting on your water heater if you need/

want hotter water.

17

Water is

heated,

but not hot

enough.

Voltage less than 240

Volts

The computer chips in your tankless water heater are

programmed with the expectation that your incoming line

voltage is 240 volts. If you have less than 240 volts [i.e.

208V or 220V], it may aect the reading on your water

heater’s digital display and cause it to read slightly higher

than the actual output temperature. To compensate

for this, increase the setting on your water heater if you

need or want hotter water.

Water is too

hot.

The water ow rate

through the heater is

too slow.

Increase the ow rate at the water outlet.

Temperature setting is

too high

Switch to a lower temperature setting.

Water Temperature at

faucet is too hot.

Check for too little ow, or if the set point temperature is

too high. This could possibly indicate a possible internal

part failure. Call us for technical assistance.

Heater

shuts o

during use.

Power outage or

faulty wiring.

Check the power supply. Check the circuit breakers.

If the problem persists, please call us for further technical

assistance.

Water stops

owing.

Possible Blockage in

water pipes or hoses.

Make sure the main water line valve is fully open, and

there are no obstructions in the water supply line.

Water

temperature

varies from

hot to cold

during use.

Water pressure has

dropped below a

minimum level.

Increase the ow rate from the water supply source.

18

14. Reset Unit

As with all electrical appliances, it is crucial to rst shut o all power to the unit directly at the fuse

or breaker box before attempting to reset this water heater.

WARNING: SERIOUS BODILY INJURY OR DEATH COULD OCCUR IF YOU IGNORE THIS

WARNING.

Locate the four reset button locations as shown below and press all buttons. If you hear a “click,”

the unit has reset. If you nd that the unit needs to be reset quite often, please call our customer

service for further assistance. Proceed to turn on your breakers and power on the unit.

19

LIMITED WARRANTY

For service, repair or any questions regarding your water heater, call the appropriate 800 number

listed within this section. Please DO NOT return the product to the place of purchase. Also, DO

NOT mail the product back to the manufacturer, nor bring it to a service center without proper

instructions and permission from one of our representatives.

The terms of this warranty are solely subject to the original owner and are at no time transferable. A

transfer of ownership will result in immediate termination of this warranty. This warranty is valid only

if the product is purchased from an authorized reseller that has an established direct relationship

with the manufacturer.

The manufacturer warrants to the original owner that our instant water heaters will be free from

defect in workmanship and material for TWO YEARS from the date of purchase, and free from

leakage for SEVEN YEARS from the date of purchase. Should any part(s) prove to be defective

during this period, the manufacturer will only be responsible for a replacement water heater or

replacement of the defective part(s). The manufacturer is not responsible for labor charges or any

incidental or consequential expenses. If a replacement water heater or part is not available, the

manufacturer’s liability is limited to the cost of the water heater or $1,000.00, whichever is less.

The manufacturer is not an insurer, and the original owner should purchase insurance to cover

damage to property or belongings. The original owner agrees to waive their right to jury trial or to

participate in a class action. Also, the original owner agrees to waive subordination to the extent a

loss is covered by insurance, so that their insurance company cannot proceed with action against

the manufacturer for recovery of any claims. Furthermore, all requests must be arbitrated in the

state of New Jersey.

Should the owner wish to return the water heater for repair, the owner must rst secure written

authorization from the manufacturer. The owner shall be required to show proof of purchase date

and to pay all transportation costs to return the defective part(s) or water heater for repair or

replacement. Warranty is void if: (i) water heater has been installed or used improperly; (ii) design

has been altered in any way; (iii) water heater has been installed and/or serviced by someone other

than a licensed electrician; (iv) or if the water heater has been installed or used in contradiction to

installation instructions, applicable laws and/or ordinances.

BLACK & DECKER, BLACK+DECKER, the BLACK & DECKER and BLACK+DECKER logos and

product names and the orange and black color scheme are trademarks of Stanley Black & Decker,

www.bdwaterheaters.com Ph: 1-844-746-6688

E-mail: [email protected]

Imported by:

Paragon Group USA,

Englewood, NJ, 07631

USA

Notes:

La page charge ...

BLACK+DECKER BD-11-DWH Manuel utilisateur

BLACK+DECKER BD-11-DWH Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents