Greenlee CMT-90 Clamp-on Meter with Diode Test Manual Manuel utilisateur

CMT-90

Clamp-on Meter

Medidor

con pinza

Contrôleur

numérique

à pinces

INSTRUCTION MANUAL

MANUAL DE INSTRUCCIONES

MANUEL D’INSTRUCTIONS

Read and understand all of the instructions and safety

information in this manual before operating or servicing

thistool.

Lea y entienda todas las instrucciones y la información

sobre seguridad que aparecen en este manual, antes de

manejar estas herramientas o darles mantenimiento.

Lire attentivement et bien comprendre toutes les

instructions et les informations sur la sécurité de ce manuel

avant d’utiliser ou de procéder à l’entretien de cet outil.

Register this product at www.greenlee.com / Registre este producto

en www.greenlee.com / Enregistrez votre produit en ligne, www.greenlee.com

2

Description

The Greenlee CMT-90 Digital Clamp-on Meter is a hand-held testing device with the

following measurement capabilities: AC and DC voltage, AC current, and resistance.

It also tests diodes and veriﬁes continuity. The CMT-90 is a true RMS-reading meter.

This unit automatically determines measurement function based on input. It has a

smart data hold feature with audible and visual alert if the input changes signiﬁcantly

while the unit is in HOLD mode. The unit automatically enters HOLD mode when the

jaw is removed from a conductor while measuring AC current. It performs a self-test

and displays approximate remaining battery capacity during the power-up sequence.

The Automatic Power Off feature can be disabled if desired.

The display automatically illuminates for easy viewing in dark areas.

Safety

Safety is essential in the use and maintenance of Greenlee tools and equipment. This

instruction manual and any markings on the tool provide information for avoiding

hazards and unsafe practices related to the use of this tool. Observe all of the safety

information provided.

Purpose of This Manual

This instruction manual is intended to familiarize all personnel with the safe opera-

tion and maintenance procedures for the Greenlee CMT-90 Digital Clamp-on Meter.

Keep this manual available to all personnel.

Replacement manuals are available upon request at no charge

at www.greenlee.com.

KEEP THIS MANUAL

All speciﬁcations are nominal and may change as design improvements occur.

Greenlee Tools, Inc. shall not be liable for damages resulting from misapplication or misuse of its

products.

® Registered: The color green for electrical test instruments is a registered trademark of

Greenlee Tools, Inc.

Do not discard this product or throw away!

For recycling information, go to www.greenlee.com.

3

CMT-90

Important Safety Information

SAFETY ALERT SYMBOL

This symbol is used to call your attention to hazards or unsafe practices which

could result in an injury or property damage. The signal word, deﬁned below,

indicates the severity of the hazard. The message after the signal word provides

information for preventing or avoiding the hazard.

Immediate hazards which, if not avoided, WILL result in severe injury or death.

Hazards which, if not avoided, COULD result in severe injury or death.

Hazards or unsafe practices which, if not avoided, MAY result in injury or

property damage.

Read and understand this material before operating or

servicing this equipment. Failure to understand how to safely

operate this tool could result in an accident causing serious

injury or death.

4

Important Safety Information

Electric shock hazard:

Contact with live circuits could result in severe injury or death.

Electric shock and ﬁre hazard:

• Do not expose this unit to rain or moisture.

• Do not use the unit if it is wet or damaged.

• Use test leads or accessories that are appropriate for the application. Refer to

the category and voltage rating of the test lead or accessory.

• Inspect the test leads or accessory before use. They must be clean and dry, and

the insulation must be in good condition.

• Use this unit for the manufacturer’s intended purpose only, as described in this

manual. Any other use can impair the protection provided by the unit.

Failure to observe these warnings could result in severe injury or death.

Electric shock hazard:

• Do not apply more than the rated voltage between any two input terminals, or

between any input terminal and earth ground.

• Do not contact the test lead tips or any uninsulated portion of the accessory.

Failure to observe these warnings could result in severe injury or death.

5

CMT-90

Important Safety Information

Electric shock hazard:

• Do not operate with the case or battery cover open.

• Before removing the case or battery cover, remove the test leads (or jaw) from

the circuit and shut off the unit.

Failure to observe these warnings could result in severe injury or death.

Electric shock hazard:

• Unless measuring voltage or current, shut off and lock out power. Make sure that

all capacitors are discharged. Voltage must not be present.

• Using this unit near equipment that generates electromagnetic interference can

result in unstable or inaccurate readings.

Failure to observe these warnings could result in severe injury or death.

Electric shock hazard:

• Do not attempt to repair this unit. It contains no user-serviceable parts.

• Do not expose the unit to extremes in temperature or high humidity.

Refer to “Speciﬁcations.”

• Do not connect to voltage for longer than 30 seconds.

Failure to observe these precautions may result in injury and can damage the unit.

Electric shock hazard:

Do not use the meter to measure voltages in circuits that could be damaged or

actuated by the meter’s low input impedance (approximately 4 kΩ).

Failure to observe this precaution may result in injury and can damage the unit.

6

Identiﬁcation

1. Jaw

2. Lever

3. Display

4. Common (COM) input terminal

5. Volts or resistance (V-Ω) input terminal

6. ON/OFF/HOLD button

7. Sensor for automatic backlit display

Display Icons

8. Low battery indicator

9. – Polarity indicator

10. Measured voltage is greater than

30 volts AC or DC

11. AutoSense Automatic selection is active

12. Automatic Power Off is enabled

13. AutoHold Hold function is enabled

14. LoZi Low input impedance is active

15. AC AC measurement is selected

16. Continuity

17. DC DC measurement is selected

18. Diode

19. A Amperes

20. V Voltage

21. % Percent

22. k Kilo (10

3

)

23. Ω Ohms

24. OL Overload indicator

Symbols on the Unit

Warning—Read the instruction manual

Electric shock hazard

Application around and removal from hazardous live conductors is permitted.

Double insulation

Battery

Recycle product in accordance with manufacturer’s directions

Note: Icons that

appear on the display

but are not identiﬁed

are not used on this

model.

1

2

3

4 5

6

7

8

9

10

11-12

13-15

16-17

18-20

21-23

24

7

CMT-90

Using the Features

• ON/OFF/HOLD: Momentarily press the ON/OFF/HOLD button to hold the present

measurement on the display; momentarily press again to return to the normal

display mode. Press and hold to turn the unit on or off.

• Smart Hold: The hold feature is disabled when “OL” is displayed on the LCD. The

LCD will blink and the beeper will sound if the unit is in HOLD mode and the input

increases by 5.0 volts or 5.0 amps. It will also blink and ﬂash if the unit is in HOLD

mode and detects an input type change, such as from AC volts to AC amps.

• Auto Hold (AC amps only): The unit automatically holds a stable AC current

measurement that is 3 amps or more. The unit beeps three times to indicate it has

saved the stable value. This value will be displayed for 5 seconds after the unit

is removed from the conductor. The value can be recalled by pressing the HOLD

button. To enable this feature, press and hold the ON/OFF/HOLD button until the

“AutoHold” icon blinks when turning the unit on, approximately 5 seconds.

• Battery Capacity Display: The unit displays the percentage of remaining battery

capacity when it is powering up. Replace the battery when “0%” is shown.

• Power-on Self-test: The unit automatically tests its internal circuitry after it

displays battery capacity. If a problem is found, the LCD will display “FAIL”. Do not

use the meter if “FAIL” is shown on the LCD.

Note: Do not measure while powering up as this could cause an incorrect self-test

failure.

• Automatic Power Off: To extend battery life, the unit will shut itself off after

approximately 20 minutes of inactivity. To disable this feature, press and hold

the ON/OFF/HOLD button until the “APO” icon blinks when turning the unit on,

approximately 3 seconds.

8

AC Measurement

AC measurements are usually displayed as RMS (root mean squared) values. Two

methods of AC measurement are average-responding RMS calibrated and true

RMS-reading.

The average-responding RMS calibrated method takes the average value of the input

signal, multiplies it by 1.11, and displays the result. This method is accurate if the

input signal is a pure sine wave.

The true RMS-reading method uses internal circuitry to read the true RMS value. This

method is accurate, within the speciﬁed crest factor limitations, whether the input

signal is a pure sine wave, a square wave, sawtooth wave, half wave or signal with

harmonics. The ability to read true RMS provides much more measurement versatil-

ity. The Greenlee CMT-90 is a true RMS meter.

The Waveforms and Crest Factors table shows some typical AC signals and their

RMS values.

Waveforms and Crest Factors

Waveform

RMS Value 100 100 100 100

Rectiﬁed Value 90 100 87 64

Crest Factor*

(x)

1.414 1 1.73 2

* The crest factor is the ratio of the peak value to the RMS value; it is represented

by the Greek letter x.

9

CMT-90

Operation

Electric shock hazard:

Contact with live circuits could result in severe injury or death.

1. The meter automatically selects the proper measurement according to the

following table.

Priority Display Conditions

1

AC volts or DC volts,

whichever is greater

Input at terminals is

1.3 to 999.9 VAC

2.1 to 999.9 VDC

-0.7 to -999.9 VDC

2

Resistance and

continuity

Input at terminals is

0 to ∞ Ω

0 to 0.9 VAC

1.0 to 2.0 VDC

-0.2 to -0.4 VDC

3 Diode test

Input at terminals is

0.4 to 0.8 VDC

4 AC amps

AC current through jaw is

0.9 to 600.0 A

2. Refer to “Typical Measurements” for speciﬁc measurement instructions.

3. Test the unit on a known functioning circuit or component of the type you intend

to measure.

• If the unit does not function as expected on a known functioning circuit,

replace the battery.

• If the unit still does not function as expected, send the unit to Greenlee for

repair. Refer to the instructions under the Warranty.

4. Take the reading from the circuit or component to be tested.

10

Typical Measurements

Current Measurement—

Clamp Around Wire

Notes:

• Clamp the jaw around one conductor only.

• Close the jaw completely to ensure accurate

measurement.

• Center the wire in the jaw for highest accuracy.

Current Measurement—

Clamp Around Line Splitter

Notes:

• The Greenlee 93-30 Line Splitter is divided. One

section renders amps; the other renders amps

multiplied by 10.

• Close the jaw completely to ensure accurate

measurement.

• Center the line splitter in the jaw for highest

accuracy.

11

CMT-90

Typical Measurements

Voltage Measurement

Resistance Measurement

12

Typical Measurements

Continuity Check

Diode Measurement

Forward Bias

Reverse Bias

13

CMT-90

Accuracy

Refer to “Speciﬁcations” for operating conditions and temperature coefﬁcient.

Accuracy is speciﬁed as follows: ± (a percentage of the reading + a ﬁxed amount) at

23 °C ± 5 °C (73.4 °F ± 9 °F), 0% to 80% relative humidity.

Accuracy for AC measurements is speciﬁed for input crest factors that do not exceed

the values in the “Maximum Input Crest Factor” table on this page.

Accuracy Table

Characteristic Range Accuracy

Frequency

Range

AC Current

0.9 to 170.0 A ± (1.9% + 1 A)

50 to 60 Hz

170.1 to 600.0 A ± (1.9% + 2A)

AC Voltage* 1.3 to 999.9 V ± (1.5% + 0.3 V) 50 to 500 Hz

DC Voltage*

2.1 to 999.9 V ± (1.0% + 0.2 V)

N/A

-0.7 to -999.9 V ± (1.0% + 0.4 V)

Resistance**

0 to 999 Ω ± (2.0% + 4 Ω)

N/A

1.000 to 9.999 kΩ ± (2.0% + 0.004 kΩ)

Diode Test 0.4 to 0.8 V ± (1.0% + 0.2 V) N/A

* Input impedance: 4 kΩ nominal at voltages up to 30 V; increases with voltage

to approximately 375 kΩ at 1000 V

** Open circuit voltage: 1.5 V maximum

Maximum Input Crest Factor

Maximum Crest Factor Current Range Voltage Range

1.414 0.9 to 6.0 A 1.3 to 3.0 V

3 6.1 to 20.0 A 3.1 to 10.0 V

5 20.1 to 500.0 A 10.1 to 250.0 V

Linear decrease from 5to 1.5

over range shown

500.1 to 600.0 A 250.1 to 999.9 V

Continuity

Tone on: Circuit resistance is ≤ 25 Ω (approximately).

Tone off: Circuit resistance is ≥ 400 Ω (approximately).

14

Speciﬁcations

Display: 10,000-count LCD

Maximum Conductor Size: 33 mm (1.30")

Display update rate is 3 per second for voltage, diode test, and resistance;

2 per second for current

Duty Cycle (voltage above 30 V):

30 seconds ON (maximum)

2 minutes OFF (minimum)

Automatic Power Off: After approximately 20 minutes

Temperature Coefﬁcient: 0.2 x (Accuracy) per °C below 18 °C or above 28 °C

Measurement Categories: Category III, 1000 V, and Category IV, 600 V

Operating Conditions:

Temperature:

0 °C to 30 °C (32 °F to 86 °F), 0% to 80% relative humidity

30 °C to 40 °C (86 °F to 104 °F), 0% to 75% relative humidity

40 °C to 50 °C (104 °F to 122 °F), 0% to 45% relative humidity

Altitude: 2000 m (6500') maximum

Indoor use only

Storage Conditions: –20 °C to 60 °C (–4 °F to 140 °F),

0% to 80% relative humidity

Remove battery

Pollution Degree: 2

Battery: 9 V battery (NEDA 1604, JIS 006P or IEC 6F22)

Battery Life: Approximately 250 hours with alkaline battery

15

CMT-90

Measurement Categories

These deﬁnitions were derived from the international safety standard for insula-

tion coordination as it applies to measurement, control, and laboratory equipment.

These measurement categories are explained in more detail by the International

Electrotechnical Commission; refer to either of their publications: IEC 61010-1 or

IEC60664.

Measurement Category I

Signal level. Electronic and telecommunication equipment, or parts thereof. Some

examples include transient-protected electronic circuits inside photocopiers and

modems.

Measurement Category II

Local level. Appliances, portable equipment, and the circuits they are plugged into.

Some examples include light ﬁxtures, televisions, and long branch circuits.

Measurement Category III

Distribution level. Permanently installed machines and the circuits they are hard-

wired to. Some examples include conveyor systems and the main circuit breaker

panels of a building’s electrical system.

Measurement Category IV

Primary supply level. Overhead lines and other cable systems. Some examples

include cables, meters, transformers, and other exterior equipment owned by the

power utility.

Statement of Conformity

Greenlee Tools, Inc. is certiﬁed in accordance with ISO 9001 (2000) for our Quality

Management Systems.

The instrument enclosed has been checked and/or calibrated using equipment that

is traceable to the National Institute for Standards and Technology (NIST).

16

Maintenance

Electric shock hazard:

• Do not attempt to repair this unit. It contains no user-serviceable parts.

• Do not expose the unit to extremes in temperature or high humidity.

Refer to “Speciﬁcations.”

Failure to observe these precautions may result in injury and can damage the unit.

Battery Replacement

Electric shock hazard:

Before removing the case or battery cover, remove the test leads (or jaw) from the

circuit and shut off the unit.

Failure to observe this warning could result in severe injury or death.

1. Disconnect the unit from the circuit.

2. Remove the screws from the battery cover.

3. Remove the battery cover.

4. Replace the battery. Observe polarity.

5. Replace the cover and screws.

Cleaning

Periodically wipe the case with a damp cloth and mild detergent; do not use

abrasives or solvents.

17

CMT-90

Descripción

El Medidor digital con pinza modelo CMT-90 de Greenlee es un instrumento de

veriﬁcación capaz de efectuar los siguientes tipos de mediciones: tensión alterna

y continua, corriente alterna y resistencia. Esta unidad es de bolsillo y cabe

perfectamente en la palma de la mano. Sirve también para probar diodos y veriﬁcar

continuidad. El modelo CMT-90 es un multímetro de lectura de valores eﬁcaces

reales.

Esta unidad determina automáticamente la función de medición según la entrada.

Posee una característica inteligente de retención de datos con alerta audible y visual

si la entrada cambia signiﬁcativamente mientras la unidad se encuentra en modo

HOLD (RETENCIÓN DE DATOS EN PANTALLA). La unidad se activa automáticamente

en modo HOLD cuando la pinza se retira de un conductor durante la medición de

corriente de CA. Lleva a cabo una autoveriﬁcación y muestra aproximadamente

la capacidad restante de la pila durante la secuencia de encendido. Se puede

inhabilitar la característica de apagado automático si así se desea.

La pantalla se ilumina automáticamente para ayudar a visualizar objetos en áreas

oscuras.

Acerca de la seguridad

Es fundamental observar métodos seguros al utilizar y dar mantenimiento a las

herramientas y equipo Greenlee. Este manual de instrucciones y todas las marcas

que ostenta la herramienta le ofrecen la información necesaria para evitar riesgos

y hábitos poco seguros relacionados con su uso. Siga toda la información sobre

seguridad que se proporciona.

Propósito de este manual

Este manual de instrucciones tiene como propósito familiarizar a todo el personal

con los procedimientos de operación y mantenimiento seguros para el Medidor con

pinza, modelo CMT-90 de Greenlee.

Mantenga siempre este manual al alcance de todo el personal.

Puede obtener copias adicionales de manera gratuita, previa solicitud en

www.greenlee.com.

CONSERVE ESTE MANUAL

Todas las especiﬁcaciones son nominales y pueden cambiar conforme tengan lugar mejoras de

diseño. Greenlee Tools, Inc. no se hace responsable de los daños que puedan surgir de la mala

aplicación o mal uso de sus productos.

® Registrado:El color verde para instrumentos de veriﬁcación eléctricos es una marca

registrada de Greenlee Tools, Inc.

¡No deseche ni descarte este producto!

Para información sobre reciclaje, visite www.greenlee.com.

18

Importante Información sobre Seguridad

SÍMBOLO DE ALERTA

SOBRE SEGURIDAD

Este símbolo se utiliza para indicar un riesgo o práctica poco segura que podría

ocasionar lesiones o daños materiales. Cada uno de los siguientes términos

denota la gravedad del riesgo. El mensaje que sigue a dichos términos le indica

cómo puede evitar o prevenir ese riesgo.

Peligros inmediatos que, de no evitarse, OCASIONARÁN graves lesiones o

incluso la muerte.

Peligros que, de no evitarse, PODRÍAN OCASIONAR graves lesiones o incluso la

muerte.

Peligro o prácticas peligrosas que, de no evitarse, PUEDEN OCASIONAR lesiones

o daños materiales.

Lea y entienda este documento antes de manejar esta

herramienta o darle mantenimiento. Utilizarla sin comprender

cómo manejarla de manera segura podría ocasionar un

accidente y, como resultado de éste, graves lesiones o incluso

la muerte.

19

CMT-90

Importante Información sobre Seguridad

Peligro de electrocución:

El contacto con circuitos activados podría ocasionar graves

lesiones o incluso la muerte.

Peligro de electrocución e incendio:

• No exponga esta unidad ni a la lluvia ni a la humedad.

• No utilice esta unidad si se encuentra mojada o dañada.

• Utilice cables de prueba y accesorios que sean apropiados para la aplicación

que se va a realizar. Consulte la información sobre categoría y voltaje nominal

del cable de prueba o el accesorio.

• Revise minuciosamente los cables de prueba o el accesorio, antes de utilizarlos.

Deberán estar limpios y secos, y su forro aislante deberá hallarse en buenas

condiciones.

• Utilícela únicamente para el propósito para el que ha sido diseñada por el

fabricante, tal como se describe en este manual. Cualquier otro uso puede

menoscabar la protección proporcionada por la unidad.

De no observarse estas advertencias podrían sufrirse graves lesiones o incluso la

muerte.

Peligro de electrocución:

• No aplique más del voltaje nominal entre dos terminales de entrada

cualesquiera, o entre una terminal de entrada cualquiera y una conexión a tierra.

• No toque las puntas de los cables de prueba ni ninguna parte del accesorio que

carezca de forro aislante.

De no observarse estas advertencias podrían sufrirse graves lesiones o incluso la

muerte.

20

Importante Información sobre Seguridad

Peligro de electrocución:

• No haga funcionar esta unidad con la caja o la tapa del compartimiento de las

pilas abierta.

• Antes de retirar la caja o la tapa del compartimiento de las pilas, retire del

circuito los cables de prueba (o la pinza), y apague la unidad.

De no observarse estas advertencias podrían sufrirse graves lesiones o incluso la

muerte.

Peligro de electrocución:

• A menos que vaya a medir tensión o corriente, apague y bloquee la energía.

Asegúrese de que todos los condensadores estén totalmente sin carga. No debe

haber tensión alguna.

• Al utilizar esta unidad cerca de equipo que genere interferencia

electromagnética quizá se obtenga una lectura inexacta e inestable.

De no observarse estas advertencias podrían sufrirse graves lesiones o incluso la

muerte.

Peligro de electrocución:

• No intente reparar esta unidad, ya que contiene partes que deben recibir

mantenimiento por parte de un profesional.

• No exponga la unidad a ambientes de temperatura extrema o altos niveles de

humedad. Consulte la sección “Especiﬁcaciones”.

• No conecte a tensión por más de 30 segundos.

De no observarse estas precauciones pudieran sufrirse lesiones o daños a la

unidad.

Peligro de electrocución:

No utilice el medidor para medir tensiones en circuitos que pudieran dañarse o

accionarse debido a la impedancia baja de entrada del medidor (aproximadamente

4 kΩ).

De no observarse esta advertencia pudieran sufrirse lesiones o daños a la unidad.

La page charge ...

Greenlee CMT-90 Clamp-on Meter with Diode Test Manual Manuel utilisateur

Ce manuel convient également à

Greenlee CMT-90 Clamp-on Meter with Diode Test Manual Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents