Posiflex JIVA HS-3310A Manuel utilisateur

Marque: Posiflex

Modèle: JIVA HS-3310A

Catégorie: Imprimantes d'étiquettes

Taper: Manuel utilisateur

Ce manuel convient également à

Package Contents

 HS-3310A/3314A desktop POS (x 1)

 24V/60W Power Adaptor (x 1)

 Power cord (x 1)

 3-inch wide thermal paper roll (x 1)

 Paper separator for 2” thermal paper roll (x 1)

 Desktop mounting kit pack for HS-3310A (x 1)

(including 1 desktop mounting bracket,

4 fixing screws, and 4 plastic anchors)

 Desktop mounting kit pack for HS-3314A (x 1)

(including 1 bottom plate, 1 desktop mounting

bracket, 4 fixing screws, and 4 plastic anchors)

 User manual (x 1)

15670902010 Ver. A0

http://www.posiflex.com

HS-3310A/3314A

JIVA Desktop POS

User Manual

SOME IMPORTANT NOTES

FCC NOTES

This system meets industry & government requirements and applicable

standards. This equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions

manual, may cause interference to radio communications. It has been tested

and found to comply with limits for a Class A digital device pursuant to

subpart B of Part 15 of FCC Rules, which are designed to provide reasonable

protection against interference when operated in a commercial environment.

Operation of this equipment in a residential area is likely to cause interference

in which case the user at his own expense will be required to take whatever

measures to correct the interference.

This device complies with part 15 of the FCC Rules. Operation is subject to

the following two conditions: (1) This device may not cause harmful

interference, and (2) this device must accept any interference received,

including interference that may cause undesired operation.

CE CLASS A WARNING

This equipment is compliant with Class A of CISPR 32. In a residential

environment this equipment may cause radio interference.

WARRANTY LIMITS

Warranty will terminate automatically when the machine is opened by any

person other than the authorized technicians. The user should consult his/her

dealer for the problem happening. Warranty voids if the user does not follow

the instructions in application of this merchandise. The manufacturer is by no

means responsible for any damage or hazard caused by improper application.

警告使用者

這是甲類的資訊產品，在居住的環境中使用時，可能會造成射頻干擾，在這種情

況下，使用者會被要求採取某些適當的對策。

BATTERY CAUTION NOTES

 Dispose of used batteries according to the instructions.

 Replacement of a battery with an incorrect type that can defeat a

safeguard (for example, in the case of some lithium battery types)

 Disposal of a battery into fire or a hot oven, or mechanically crushing

or cutting of a battery that can result in an explosion.

 Leaving a battery in an extremely high temperature surrounding

environment that can result in an explosion or the leakage of flammable

liquid or gas.

 A battery subjected to extremely low air pressure that may result in an

explosion or the leakage of flammable liquid or gas.

BATTERIE ATTENTION NOTES

 Jetez les piles usagées conformément aux instructions.

 Remplacement d'une batterie avec un type incorrect qui peut annuler

une sauvegarde (par exemple, dans le cas de certains types de batterie

au lithium)

 Mise au rebut d'une batterie dans le feu ou dans un four chaud, ou

écrasement ou coupure mécanique d'une batterie pouvant entraîner une

explosion.

 Laisser une batterie dans un environnement environnant à des

températures extrêmement élevées pouvant entraîner une explosion ou

la fuite de liquide ou de gaz inflammable.

 Une batterie soumise à une pression atmosphérique extrêmement basse

pouvant provoquer une explosion ou une fuite de liquide ou de gaz

inflammable.

警告

本電池如果更換不正確會有爆炸的危險，請依製造商說明書處理用過之

電池。

Cable Exit

Views of HS-3310A/3314A

Front View

Rear View

Power LED Indicator

Printer Error

LED Indicator

Printer Paper-Out

LED Indicator

3-Track Magnetic

Stripe Reader

(Optional)

Printed Paper Exit

HS-3310A/3314A

P-CAP Touch & LCD Panel

Fingerprint or iButton

Sensors (Optional)

Posiflex 2D Scanner

(Optional)

Paper Jam Rescue

Compartment

Top I/O Interface

Cable Cover

Bottom I/O Interface

Cable Cover

Feed Button

Left Side View

Right Side View

Power Button

Paper Roll Cover

Release Lever

RFID Card Reader

(Optional)

Bottom View

Views of I/O Interface of HS-3310A/3314A

Top I/O Interface

Bottom I/O Interface

Rubber Pad

HDMI Port

Rubber Pad

Mounting holes

USB 3.0 Port

24V DC-IN Power Jack

Micro SD Card Slot

RJ-10 Cash Drawer Port

USB 2.0 Port

Micro USB OTG

Reset Button

Line Out Port

USB 2.0 Port

DB-9 COM Ports

RJ-45 LAN Port

12V DC-OUT

Power Jack

Connecting Power Adapter

Please refer to the following instructions on how to connect power adapter to

HS-3310A/3314A and to organize your cables.

1. Lay your desktop POS on a level surface

with its touch screen facing down as shown

in the figure.

2. Hold the bottom I/O interface cover with

your thumb and forefinger, and then gently

pull the cover outwards to remove the

cover.

3. Connect power adapter and I/O cables to

the bottom I/O interface.

4. Have the cover join to the wedge portions

of the bottom I/O interface.

5. Before pushing the cover back into place,

neatly thread the cables through the cable

exit.

6. Press down the cover to close the bottom

I/O interface chamber.

Cable Exit

Loading 2” or 3” Paper Rolls

Before operating the printer, please follow the below steps to load a paper roll.

1. To open the paper roll cover, push down the

paper roll cover release lever in the direction

shown in the figure.

2. Before installing 2-inch paper roll in the thermal printer, place paper

separator in the paper roll compartment by following the instructions

below. If you are using 3” paper roll for the printer, please skip to

next step.

2.1. Hold the separator with the sharp-

pointed side down.

2.2. Push the sharp-pointed part of paper

separator into the slot on the bottom

of the paper roll compartment.

2.3. Slide another side of paper separator into the slot on the top

of the paper roll compartment.

2.4. Drop 2-inch paper roll inside the

paper roll compartment.

3. To load the thermal printer with the 3-inch

paper roll, just drop the thermal paper roll

inside the paper roll compartment of the

printer as illustrated in the figure.

4. Unroll the thermal paper and drag the loose

end of the paper till it extends towards the

paper cutter.

5. Make sure the loose end sticks out of the

opening of the paper roll compartment. Then,

close the paper roll cover by pushing it back

at the center of the top side of the cover with

a click sound.

6. Make sure the paper roll is well loaded with

the end of the paper sticking out as shown in

the figure.

To avoid paper jam or other printing errors, do NOT

press the paper roll cover release lever during printing.

Paper cutter

Troubleshooting Paper Jams

When it comes to the common printing problems, it is inevitable that you

might encounter the issue of paper jams at some point. The following steps are

provided to assist you in fixing the problem. Before proceeding, make sure that

your POS terminal is properly shut down.

1. Open the paper jams rescue compartment by

sliding the cover in the direction shown by

the arrow.

2. In the paper jams rescue compartment, find

the adjustment wheel, which mainly allows

you to manually adjust the cutting position of

the cutter blade.

3. Keep rotating the wheel until the cutter blade

is completely retracted.

4. Observe the cutter position through the paper exit slot to ensure the

cutter blade moves upward to the retracted position.

5. Gently push down paper roll cover release

lever to open the paper roll cover. If the

cover is still stuck, please repeat Step 3 and

Step 4.

6. Remove the jammed paper, reinstall the paper roll, and then close the

paper roll cover firmly.

Adjustment wheel

Replacing POS Receipt Printer Module

HS-3310A/3314A offers a quick solution to help you to replace POS receipt

printer module when there is a need. Please go through the steps described

below to achieve the purpose. Before proceeding the procedure, please ensure

that the terminal is completely shut down.

1. After laying POS terminal on a flat surface

with its bottom facing towards you, remove

the screw shown by the arrow.

2. Position the terminal with its screen facing

toward you, and then push down the paper roll

cover release lever to open the paper roll cover,

3. Inside the paper roll compartment, remove the

two screws indicated by the arrows.

4. While supporting the terminal with one hand,

grab the right-hand side of the terminal and

then pull the front cover towards you with

force to separate the printer module from the

rear case of HS-series

5. From the left-hand side of the terminal, remove

the front cove from the rear case.

6. Disconnect all the cables indicated in the figure.

7. Take the new printer module which you wish to replace with, and then

connect the cables to the printer control board as indicated in the

following figures.

7.1 Connect the CR cable to CR port on the

control board.

7.2 Insert the cable to the port for printer

signal on the control board.

7.3 Attach the USB cable to Type-B USB

port on the control board.

7.4 Plug the cable to DC-IN power jack on

the control board.

8. Carefully support the printer module with

both of your hands and then push it back into

the rear case of HS-series terminals.

9. After ensuring the front cover is well

attached to the rear case, insert the two

screws back into the screw holes inside the

compartment, secure them, and then close the

cover.

10. Insert the screw which you removed in step 1

to the screw hole at the bottom, and then

fasten it properly, as the figure shows.

Mounting the POS onto a Table

This section will describe two alternative solutions to help you fix the POS

firmly onto a table in preventing your POS system from being rocked, tipped

or tilted accidentally.

Using bottom plate

Please follow the steps below to install the bottom plate for HS-3114A.

1. Take the bottom plate with the mounting bracket out of the package,

and place it with its screw holes on the top in your preferred position.

2. Support your POS terminal with its

screen facing towards you. Then, align

the two screw bolts on the bottom of the

POS with the rail slots of the mounting

bracket.

3. Push the POS backwards along the rail slots of the bracket until the

terminal is locked into place.

Bottom Plate

Mounting bracket

Screw holes

4. After inserting another two scerws into the two mouting holes located

on the rear of the POS, fasten them to fix the POS termial to the

bottom plate.

Using desktop-mounting kits

Please follow the steps below to install desktop-mounting kits.

1. Please first release the mounting bracket from the bottom plate by

removing two screws as shown in the figure.

2. After placing the mounting bracket in your

preferred mounting position, use the screw

holes of the mounting bracket to drill two

holes on the surface. Each hole has to be at

least

” or 6.25 mm diameter and

” or

35mm in depth.

3. Insert two plastic anchors into the holes you

drilled in step 2 and use a hammer to tap the

plastic anchors into the drilled holes.

4. After well attaching two screw holes of the mounting bracket to the

plastic anchors, insert two self-tapping screws into the plastic anchors

through the mounting bracket and then secure the bracket.

Mounting bracket

Bottom Plate

5. Support your POS terminal with its screen

facing towards you. then, align the two screw

bolts on the bottom of the POS with the rail

slots of the mounting bracket.

6. Push the POS backward along the rail slots of the bracket until the

terminal is locked into place.

7. To completely mount the desktop POS onto the table, please follow the

steps below.

7.1 Use the two mouting holes located on the rear of the POS to drill

another two holes on the same surface. Each hole also has to be at

least

” or 6.25 mm diameter and

” or 35mm in depth.

7.2 Push the POS in the direction shown by the arrow to reomve it from

the mouting bracket.

7.3 After pushing two plastic anchors into the

drilled holes, tap the plastic anchors into the

drilled holes with a hammer.

7.4 Refer Step 6 to mount the POS to the bracket.

7.5 Apply two self-tapping screws through the mounting holes into the

two plastic anchors. Then, fasten the screws to completely lock the

POS onto the table.

Installing a Customer Display to HS-3310A/3314A

HS-3310A/3314A also allows you to additionally install a customer display to

expand its functionality. Based on the model of the second display, the step-

by-step instructions are provided in its own user guide to help you mount it

onto your POS system. Please refer to the relevant user manual for detailed

information.

Powering ON/OFF the HS-3310A/3314A

Power ON HS-3310A/3314A

To power on the POS, gently press and hold down the power button for at least

1 second till the Power LED indicator turns solid blue, and then release the

button.

Power OFF HS-3310A/3314A

To initiate a system shutdown on Android operating system, you are expected

to follow the following procedures to turn off your system:

1. Press down the power button for a few seconds until a pop-up window

appears.

2. Tap Power off on the screen to shut down your system. If you need to

reboot your system right away, please be advised to wait at least three

seconds to do so.

However, it is likely that HS-3310A/3314A cannot restart or shut down

normally due to the unexpected reasons. In such a case, it is suggested to

initiate a shutdown by keeping holding down the power button more than 10

seconds.

Operating the Magnetic Stripe Reader (Optional)

To have the magnetic stripe reader of HS-

3310A/3314A work properly, you must bear in mind

the following tips while swiping your MSR cards

through the reader.

1. Make sure to swipe your card with the side of

magnetic stripe facing up.

2. Make sure to swipe your card along the track

of the reader from left to right or from right to

left in the direction shown below.

Using the RFID Card Reader (Optional)

To retrieve data through the RFID card reader, tap

your Mifare card against the RFID reader as shown

below.

Scanning Barcodes with Posilfex 2D Scanner (Optional)

The integrated Posiflex 2D Scanner is another

prominent feature of HS-3310A/3314A. With its hand-

free design, it offers a more convenient solution for

users to read 1D/2D barcodes and then transmitted

scanned data to the terminal for further processing,

which greatly increases your working efficiency. By

default, the scanner is set to Auto Trigger operational

mode. Also, to adjust the scanning angle of the

scanner, you may tilt the scanner up and down as

indicated in the figure below.

Using Fingerprint or iButton Sensors (Optional)

As for access control to your computer, two optional identification

mechanisms are provided and integrated in HS-3310A/3314A: The

fingerprint and iButton sensors. Either will work to verify an individual’s

identity.

In order to allow the fingerprint sensor to function normally, you have to

pre-installed and accessible on your desktop of your system.

Fingerprint Sensor

iButton Sensor

Self-Diagnosing your Printer

The variety of diagnostic tips is provided in aim to help you efficiently

troubleshoot printer problems. Please carefully go through the following

descriptions to understand how each function provided works.

 Self Test

A self-test page, generated by Self Test function, generally contains

useful information describing current printer configurations. Please

follow the instructions described below to perform a self-test:

1. Power OFF printer.

2. Hold down Feed button, and then power on the printer.

3. Release Feed button after the printer emits one beep sound.

4. The printer will print a test page displaying the self-test result.

5. A flashing red Paper Out LED indicates the printing is still

processing. In this case, you may either choose to reboot your

printer or keep pressing Feed button to further create the hex

dump and Ethernet info print-outs until the indicator stops

blinking red.

 Software Switch Reset

Software Switch Reset is the specially-designed function aimed to

facilitate the factory reset process. Please go through the following

instructions to reset your printer to factory settings using Software

Switch Reset.

1. Power OFF printer.

2. Open the cover of the printer.

3. Press Feed button three times after powering on the printer.

4. Close the cover of the printer.

5. The printer will emit one long beep sound and then print a test

page displaying software switch setting

6. Afterwards, the printer will restart by itself.

7. Ensure that all the software switches are correctly set to

factory default as follows:

Software switch number

Pin Number

SW1

Pin 1 ~ 8 = OFF

SW2

Pin 1 ~ 8 = OFF

SW3

Pin 1 ~ 8 = OFF

SW4

Pin 1 ~ 8 = OFF

 Hex Dump Mode

Hex Dump Mode enables the printer to print out the received data in the

hexadecimal format. Please refer to the following instructions to activate

Hex Dump Mode.

1. Power OFF printer.

2. Open the cover of the printer.

3. Hold down Feed button, and then power on the printer.

4. Release Feed button after the printer emits one beep sound.

5. Close the cover for the printer.

6. The printer will be put into Hex Dump Mode and ready to

print data received from the host.

Status LED Indicator

After HS-3310A/3314A is powered on, it is significant to observe the status of

LED indicators anytime to ensure your system functions normally. More

importantly, knowing how to interpret the status indicators enables you to

perform basic troubleshooting more efficiently. The below chart is thus

provided to enumerate all the possible indicator lights with their meanings for

your reference.

LED

Status

Description

POWER LED

Solid orange

System standby

Solid blue

System ON

Error LED

Solid red

Cover open

Flashing red

Operating temperature of

thermal head is high

Paper-out LED

Solid red

Out of Paper

Adjusting LCD Monitor for a Better Viewing Angle

For an optimal viewing angle, please tilt the LCD

monitor up and down in the directions shown by the

arrow in the below figure. Please be advised not to

touch LCD panel while setting up the tilt angle for

HS-3310A//3314A.

Specifications

HS-3310A

HS-3314A

CPU

Rockchip RK3399

Memory

2GB or 4GB

Storage Device

16GB or 32GB eMMC onboard + micro SD slot

Power Adaptor

24V/60W

LCD Display

9.7” 1024 x 768 LCD

panel

14" 1366 x 768 LCD

panel

Operating System

Android 9.0

Touch Screen

PCAP touch with multi-touch support

Serial Port

2 x DB9 Port (on the bottom I/O plate)

CR Port

1, controlling 2 CR (24V drive)

Display Port

1 x HDMI port (on the top I/O plate)

External USB Port

3, 2 (USB 3.0 + USB 2.0) ports (on the bottom I/O

plate) + 1 x USB 2.0 ports (on the top I/O plate)

OTG USB

1 x Micro USB (USB 3.0) (on the top I/O plate)

Internal USB Port

1 x 7-pin for 4G module

1 x 12-pin for printer

1 x 5-pin for HUB board

1 x 5-pin (reserved)

Audio Port

1 x 2W speaker (internal wafer) + 1 x audio jack

DC-In Jack

1 x 24V DC-In, 3-pin (on the bottom I/O plate)

1 x 12V DC-Output jack, 2-pin (on the top I/O plate)

Ethernet Port

1 x 10/100/1000 Mb (on the bottom I/O plate)

Power Button

1 x power button

Reset Button

1 x reset button (on the top I/O plate)

Wireless Connectivity

WiFi via mini-PCIe expansion slot or USB

4G LTE via Posiflex SM-140

LED Indicator

Power ON/ standby, bi-color LED indicators

Ethernet link LED indicator on Ethernet connector

Printer error & paper-out LED indicators

Optional Items

MSR, RFID Reader, Fingerprint or iButton Sensors,

2D Scanner Sensor, 4G Module

Dimension

(W x D x H in mm)

244.5 x 198 x 434 mm

371.5 x 198 x 473 mm

Weight (N.W. in kg)

4.2

5.8

Environmental

Requirements

Operating： 0°C 〜 40°C, 20%RH - 90%RH

Storage： -20°C 〜 70°C, 10%RH - 90%RH

La page charge ...

Posiflex JIVA HS-3310A Manuel utilisateur

Marque: Posiflex

Modèle: JIVA HS-3310A

Catégorie: Imprimantes d'étiquettes

Taper: Manuel utilisateur

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Posiflex JIVA HS-3310A User manual

Posiflex JIVA HS-3310A Manuel utilisateur

Ce manuel convient également à

Posiflex JIVA HS-3310A Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents