KitchenAid KBNU367TSS00 Le manuel du propriétaire

Marque: KitchenAid

Modèle: KBNU367TSS00

Catégorie: Barbecues

Taper: Le manuel du propriétaire

Ce manuel convient également à

®itchen kid ®

OUTDOOR GRILLS

FREESTANDING AND BUILT-IN

For questions about features, operation/performance, parts, accessories or service, call: 1-800-422-1230

or visit our website at www.kitchenaid.com

In Canada, for assistance, installation and service, call: 1-800-807-6777

or visit our website at www.KitchenAid.ca

GRILS D'EXTERIEUR

AUTOPORTANTS ET ENCASTRI_S

Au Canada, pour assistance, installation ou service composez le 1-800-807-6777

ou visitez notre site web &www.KitchenAid.ca

Table of Contents/Table des matieres ............................................................................. 2

iMPORTANT:

Save for local electrical inspector's use.

Installer: Leave installation instructions with the homeowner.

Homeowner: Keep installation instructions for future reference.

iMPORTANT :

_, conserver pour consultation par I'inspecteur local des installations _lectriques.

Installateur : Remettre les instructions d'installation au propri_taire.

Propri6taire : Conserver les instructions d'installation pour r_f_rence ult_rieure.

Models/Modeles KFRU368T, KFRU488T, KBNU367T, KBNU487T

W10110725C

TABLEOF CONTENTS

OUTDOOR GRILL SAFETY ............................................................ 3

INSTALLATION REQUIREMENTS ................................................ 5

Tools and Parts ............................................................................ 5

Location Requirements ................................................................ 5

Product Dimensions ..................................................................... 6

Built-In Outdoor Grill Enclosure ................................................... 6

Cabinet Dimensions ..................................................................... 6

Electrical Requirements ............................................................... 9

Gas Supply Requirements ......................................................... 10

Gas Connection Requirements .................................................. 11

Gas Connection Requirements .................................................. 12

INSTALLATION INSTRUCTIONS ................................................ 12

Style 1 - Freestanding Outdoor Grill Installation........................ 12

Style 2 - Built-in Outdoor Grill Installation ................................. 15

Check and Adjust the Burners ................................................... 17

OUTDOOR GRILL USE ................................................................ 18

Using Your Outdoor Grill............................................................ 18

Using Your Infrared Sear Burner ................................................ 19

Using Your Side Burner ............................................................. 20

Using Your Rotisserie................................................................. 20

Rotisserie Cooking Tips ............................................................. 22

Using Your Smoker Box ............................................................ 23

Hood Lights................................................................................ 23

USING YOUR WARMING DRAWER ........................................... 23

Control Knob.............................................................................. 23

Moist-Dry Slide Control .............................................................. 24

Setting the Controls ................................................................... 24

Warming Cookware ................................................................... 25

Warming Pans and Positioning Rack ........................................ 25

Proofing Bread ........................................................................... 25

Slow Cook Function ................................................................... 25

TIPS FOR OUTDOOR GRILLING ................................................ 26

Cooking Methods ....................................................................... 26

Grilling Chart............................................................................... 27

OUTDOOR GRILL CARE ............................................................. 28

Changing the Light Bulb ............................................................ 28

General Cleaning ........................................................................ 29

Drawer Slides ............................................................................. 31

Drawer Removal ......................................................................... 31

TROUBLESHOOTING .................................................................. 31

ASSISTANCE OR SERVICE ......................................................... 32

In the U.S.A................................................................................ 32

Accessories ................................................................................ 32

In Canada ................................................................................... 32

WAR RANTY .................................................................................. 33

TABLEDES MATIERES

SI_CURITI_ DU GRIL D'EXTI_RIEUR ........................................... 35

EXIGENCES D'INSTALLATION ................................................... 37

Outillage et pieces ...................................................................... 37

Exigences d'emplacement ......................................................... 37

Dimensions du produit ............................................................... 38

Enceinte du gril d'exterieur encastre ......................................... 38

Dimensions du placard .............................................................. 38

Specifications electriques .......................................................... 41

Specifications de I'alimentation en gaz ..................................... 42

Exigences concernant le raccordement au gaz ........................ 43

Exigences concernant le raccordement au gaz ........................ 44

INSTRUCTIONS D'INSTALLATION ............................................. 44

Style 1 - Installation du gril d'exterieur autoportant .................. 44

Style 2 - Installation du gril d'exterieur encastre ....................... 47

Contr61e et reglage des brQleurs................................................ 49

UTILISATION DU GRIL D'EXTI_RIEUR ....................................... 51

Utilisation du gril d'exterieur ....................................................... 51

Utilisation du brQleur &infrarouge.............................................. 53

Utilisation du brQleur lateral........................................................ 53

Utilisation du tournebroche ........................................................ 54

Conseils de cuisson a I'aide du tournebroche .......................... 55

Utilisation du fumoir ................................................................... 56

Lampes sous le capot ................................................................ 56

UTILISATION DU TIROIR-RI_CHAUD ......................................... 57

Bouton de commande ............................................................... 57

Curseur de reglage Moist-Dry (humide-sec).............................. 57

Reglage des commandes .......................................................... 57

Ustensiles de rechauffage .......................................................... 58

Ustensiles de rechauffage et grille de positionnement .............. 58

Levee du pain ............................................................................. 59

Fonction de cuisson lente .......................................................... 59

CONSEILS POUR L'UTILISATION DU GRIL D'EXTI_RIEUR ....60

Methodes de cuisson ................................................................. 60

Tableau de cuisson au gril ......................................................... 61

ENTRETIEN DU GRIL D'EXTI_RIEUR ......................................... 63

Changement de I'ampoule d'eclairage ...................................... 63

Nettoyage gen6ral ...................................................................... 63

Glissieres de tiroir ....................................................................... 65

Depose du tiroir .......................................................................... 65

DI_PANNAGE ................................................................................. 66

ASSISTANCE OU SERVICE ......................................................... 66

Au Canada .................................................................................. 66

Accessoires ................................................................................ 67

GARANTIE ..................................................................................... 67

OUTDOOR GRILL SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow

instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

,_ DANGER

If you smell gas:

1. Shut off gas to the appliance.

2. Extinguish any open flame.

3. Open lid.

4. If odor continues, keep away from the

appliance and immediately call your

gas supplier or your fire department.

_h, WARNING

1. Do not store or use gasoline or other

flammable liquids or vapors in the

vicinity of this or any other appliance.

2. An LP cylinder not connected for use

shall not be stored in the vicinity of

this or any other appliance.

State of California Proposition 65 Warnings:

WARNING: This product contains a chemical known to the State of California to cause cancer.

WARNING: This product contains a chemical known to the State of California to cause birth defects or other reproductive harm.

In the State of Massachusetts, the following installation instructions apply:

m Installations and repairs must be performed by a qualified or licensed contractor, plumber, or gasfitter qualified or licensed by

the State of Massachusetts.

m If using a ball valve, it shall be a T-handle type.

m A flexible gas connector, when used, must not exceed 3 feet.

IMPORTANT:Thisgrillismanufacturedforoutdooruseonly.Forgrillsthataretobeusedatelevationsabove2000ft(609.6m)orifice

conversionisrequired.See"GasSupplyRequirements"section.Itistheresponsibilityoftheinstallertocomplywiththeminimum

installationclearancesspecifiedonthemodel/serialratingplate.Themodel/serialratingplateforbuilt-inmodelscanbefoundonthe

right-handsideofthegrill.Themodel/serialratingplateforfreestandingmodelscanbefoundontheright-handinsidecabinetwall.

iMPORTANT SAFETY iNSTRUCTiONS

WARNING: To reduce the risk of fire, electrical shock,

injury to persons, or damage when using the outdoor cooking

gas appliance, follow basic precautions, including the

following:

m Do not install portable or built-in outdoor cooking gas

appliances in or on a recreational vehicle, portable trailer,

boat or in any other moving installation.

m Always maintain minimum clearances from combustible

construction, see "Location Requirements" section.

m The outdoor cooking gas appliance shall not be located

under overhead unprotected combustible construction.

m This outdoor cooking gas appliance shall be used only

outdoors and shall not be used in a building, garage, or any

other enclosed area.

m Keep any electrical supply cord and fuel supply hose away

from any heated surfaces.

m Keep outdoor cooking gas appliance area clear and free

from combustible materials, gasoline and other flammable

vapors and liquids.

m Do not obstruct the flow of combustion and ventilation air.

Keep the ventilation openings of the cylinder enclosure free

and clear from debris.

m Inspect the gas cylinder supply hose before each use of the

outdoor cooking gas appliance. If the hose shows

excessive abrasion or wear, or is cut, it MUST be replaced

before using the outdoor cooking gas appliance. Contact

your dealer and use only replacement hoses specified for

use with the outdoor cooking gas appliance.

m Visually check the burner flames. They should be blue.

Slight yellow tipping is normal for LP gas.

m Check and clean burner/venturi tube for insects and insect

nest. A clogged tube can lead to fire under the outdoor

cooking gas appliance.

SAVE THESE

[] The LP gas supply cylinder to be used must be:

- constructed and marked in accordance with the

Specification for LP Gas Cylinders of the U.S. Department

of Transportation (DOT) or the National Standard of

Canada, CAN/CSA-B339, Cylinders, Spheres, and Tubes

for Transportation of Dangerous Goods; and Commission.

- provided with a listed overfilling prevention device.

- provided with a cylinder connection device compatible

with the connection for outdoor cooking gas appliances.

[] Always check connections for leaks each time you connect

and disconnect the LP gas supply cylinder. See

"Installation Instructions" section.

[] When the outdoor cooking gas appliance is not in use, the

gas must be turned off at the supply cylinder.

[] Storage of an outdoor cooking gas appliance indoors is

permissible only if the cylinder is disconnected and

removed from the outdoor cooking gas appliance.

[] Cylinders must be stored outdoors and out of the reach of

children and must not be stored in a building, garage, or

any other enclosed area.

[] The pressure regulator and hose assembly supplied with

the outdoor cooking gas appliance must be used. A

replacement pressure regulator and hose assembly

specific to your model is available from your outdoor

cooking gas appliance dealer.

[] Gas cylinder must include a collar to protect the cylinder

valve.

[] For appliances designed to use a CGA791 Connection:

Place a dust cap on cylinder valve outlet whenever the

cylinder is not in use. Only install the type of dust cap on

the cylinder valve outlet that is provided with the cylinder

valve. Other types of caps or plugs may result in leakage

of propane.

If the following information is not followed exactly, a fire

causing death or serious injury may occur.

[] Do not store a spare LP gas cylinder under or near this

outdoor cooking gas appliance.

[] Never fill the cylinder beyond 80 percent full.

INSTRUCTIONS

INSTALLATION REQUIREMENTS

Gather the required tools and parts before starting installation.

Read and follow the instructions provided with any tools listed

here.

Tools Needed

• Tape measure • Wrench or pliers

• Small, flat-blade screwdriver • Pipe wrench

• Flat-blade screwdriver • Scissors or cutting pliers

• #2 and #3 Phillips screwdriver (to remove tiedowns)

• Level • Noncorrosive leak-

detection solution

Parts Supplied

• Gas pressure regulator/hose assembly set for 11" WCP LP

gas (attached to manifold).

• Rotisserie motor mounting bracket

• Rotisserie motor

• Rotisserie forks

• Rotisserie spit

• Smoker box

• 2 warming drawer pans

• 1 single-prong plug/500 mAmp transformer assembly

• Rotisserie motor mounting bracket

• 1 single-prong plug/500 mAmp transformer assembly for the

rotisserie

• Rotisserie motor

• Rotisserie forks

• Rotisserie spit

• Smoker box

Explosion Hazard

Do not store fuel tank in a garage or indoors.

Do not store grill with fuel tank in a garage or indoors.

Failure to follow these instructions can result in death,

explosion, or fire.

Parts Needed

• 20 Ib LPgasfuel tank

Gather the required tools and parts before starting installation.

Read and follow the instructions provided with any tools listed

here.

Tools Needed

• Tape measure • Wrench or pliers

• Small, flat-blade screwdriver • Pipe wrench

• Flat-blade screwdriver • Scissors or cutting pliers

• #2 and #3 Phillips screwdriver (to remove tiedowns)

• Level • Noncorrosive leak-

detection solution

Parts Needed

• Gas line shutoff valve

• 1/2"male pipe thread nipple for connection to pressure

regulator

• LP gas-resistant pipe-joint compound

• CSA design-certified outdoor flexible stainless steel

appliance connector (4-5 ft [1.2-1.5 m]) or rigid gas supply

line as needed.

Parts Supplied

• Convertible regulator set for 4" WCP Natural gas.

• 1 single-prong plug/5,000 mAmp transformer assembly for

the grill

Fire Hazard

Do not use grill near combustible materials.

Do not store combustible materials near grill.

Doing so can result in death or fire.

Select a location that provides minimum exposure to wind and

traffic paths. The location should be away from strong draft

areas.

Do not obstruct flow of combustion and ventilation air.

Clearance to combustible construction for built-in and

freestanding outdoor grills:

• A minimum of 24" (58 cm) must be maintained between the

front of the grill hood, sides and back of the grill and any

combustible construction.

• A 24" (58 cm) minimum clearance must also be maintained

below the cooking surface and any combustible construction.

Rotisserie

A 6" (15.2 cm) minimum clearance is needed for the rotisserie

motor.

A grounded, 3-prong outlet located to the left of the grill is

required. See "Electrical Requirements" section.

Style I - Freestanding Outdoor Grill

< A

171A '' ,,_,, ..................... _',

62%"

(_8.7on,) @@ @ @ @ @ @ @

A. 84V2" (214.6 cm) on 36" (91.4 cm) models

96V2" (245.1 cm) on 48" (121.9 cm) models

B. 36" (91.4 cm)

48" (121.9 cm)

C. 14" (35.6 cm)

17W'

(43.8 cm)

28W'

(72.4 ore)

front of

handle to

back of grill

Style 2 - Built-In Outdoor Grill

361A,,

(92.1 crn)

;'7.1 cm)

- 28V2"

(72.4cm)

22%"

(57.7cm)

A. 36" (91.4 cm)

48" (121.9 cm)

B. 36" (91.4 cm) models - 40%" (103.4 em)

48" (121.9 cm) models - 523/4 '' (133.9 cm)

Fire Hazard

Do not install grill on or near combustible materials.

Doing so can result in death or fire.

The enclosure for the built-in outdoor grill is to be a minimum of

11" (28.0 cm) high x 23" (58.4 cm) deep x [39" (99.0 cm) for

36" (91.4 cm) grill and 51" (129.5 cm) for 48" (121.9 cm) grill]

wide.

This built-in outdoor grill is only for installation in a built-in

enclosure constructed only of noncombustible materials. Non-

combustible materials could be brick, firewall or steel. Do not use

wood or other combustible materials for built-in enclosure.

Cab set

Bui D,4_sOs{doo" 6158_,s

The installation of this grill must conform with local codes or, in

the absence of local codes, with either the National Fuel Gas

Code, ANSI Z223.1/NPFA 54, Natural Gas and Propane

Installation Code, CSA B149.1, or Propane Storage and Handling

Code, B149.2.

Copies of the standards listed may be obtained from:

CSA International

8501 East Pleasant Valley Rd.

Cleveland, Ohio 44131-5575

NOTE: The grill drops into the opening and is supported by its

side flanges. Do not use a bottom support.

The dimension chart and illustration below include cutout dimensions and minimum spacing requirements for all built-in outdoor

products. The illustration is for reference. The design of your cabinet layout can be personalized, but the dimensions for the cutouts and

minimum spacing must be followed.

6crn) in"

3" (7"on b°u'_

to oP

E Gri!ls orrnent C

Retted"

H A

Between 2 or more sets of Access Doors adjacent to each other:

K = 14" (35.6 cm) when 2 adjacent doors are opened to 90 degrees

K = 8" (20.3 cm) when 1 of the adjacent doors is opened to 90 degrees

Between a set of Access Doors and a Trash Drawer, Utility Drawer, Warming Drawer, Refrigerator, or Ice Maker:

K = 8" (20.3 cm) when 1 of the adjacent doors is opened to 90 degrees

Between a Trash Drawer, Utility Drawer, or Warming Drawer:

K = 3" (7.6 cm)

Cabinet Height and Depth Dimensions

Dimension A Minimum Dimension B Minimum

With outdoor refrigerator 37" (94.0 cm) 26" (66.0 cm)

Grill with insulated jacket 361/2'' (92.7 cm) 27" (68.6 cm)

Grill without insulated jacket 351/2'' (90.2 cm) 26" (66.0 cm)

Grill Size Dimension C Dimension D Dimension E

27" (68.6 cm) 29%" (75.2 cm) 10%" (27.3 cm) 227/8"(58.1 cm)

36" (91.4 cm) 38%" (98.1 cm) 10%" (27.3 cm) 227/8'' (58.1 cm)

48" (121.9 cm) 50%" (128.6 cm) 10%" (27.3 cm) 227/8'' (58.1 cm)

Grill Size Dimension C Dimension D Dimension E

27" (68.6 cm) 33" (83.8 cm) 11%" (29.8 cm) 24" (61.0 cm)

36" (91.4 cm) 42" (106.7 cm) 11%" (29.8 cm) 24" (61.0 cm)

48" (121.9 cm) 54" (137.2 cm) 11%" (29.8 cm) 24" (61.0 cm)

Cutout Dimensions - Built-in Side Burner

Burner Position Dimension C Dimension D Dimension E

Front to Back 131/2"(34.3 cm) 10%" (27.3 cm) 22%" (57.5 cm)

Side by Side 241/2'' (62.2 cm) 10%" (27.3 cm) 167/8'' (42.9 cm)

Dimension C Dimension D Dimension E

131/2"(34.3 cm) 10%" (27.0 cm) 221V16'' (57.6 cm)

Cutout Dimensions - Built-in Refreshment Center

Dimension C Dimension D Dimension E

301/2"(77.5 cm) 10%" (27.3 cm) 23" (58.4 cm)

Cutout Dimensions - Built-in Access Doors

Door Size Dimension F Dimension L*

18" (45.7 cm) 163/16"(41.1 cm) 11/2"(3.8 cm)

27" (68.6 cm) 251/8'' (63.8 cm) 11/2"(3.8 cm)

30" (76.2 cm) 281/8'' (71.4 cm) 11/2"(3.8 cm)

36" (91.4 cm) 341/8'' (86.7 cm) 11/2"(3.8 cm)

48" (121.9 cm) 461/8'' (117.2 cm) 11/2'' (3.8 cm)

*Dimension L is the minimum mounting surface area around the opening for mounting the optional door or drawers.

Cutout Dimensions - Outdoor Refrigerator

Dimension G Dimension H

24" (61.0 cm) 351_'' (89.5 cm)

Dimension G Dimension H

18" (45.7 cm) 34" (86.4 cm) min. to 341/2"(87.6 cm) max.

Warming Drawer Size Dimension J

24" (61.0 cm) 221/2'' (57.2 cm)

Cutout Dimensions - Built-in Utility Drawer and Built-in Trash Drawer

Dimension M Dimension L*

12W' (31.1 cm) 11/2"(3.8 cm)

*Dimension L is the minimum mounting surface area around the opening for mounting the optional door or drawers.

Built-in Outdoor Grill Enclosure Ventilation for LP Gas:

An enclosure for an LP gas fuel tank is to be ventilated by

openings at both the top and lower levels of the enclosure.

If converting to LP gas these vents are to be in the enclosure:

An enclosure for use with an LP gas fuel tank for built-in

installation is to have at least one ventilation opening on an

exposed exterior side located within 5" (12.7 cm) of the top is to

be a minimum of 20 in.2(129.0 cm2). One ventilation opening

within 1" (2.5 cm) of the bottom of the enclosure and the bottom

opening is to be a minimum of 10 in.2(64.5 cm_).All vent

openings are to be unobstructed. Every opening is to be a

minimum of 1/8"(0.32 cm) wide.

20 in? (129.0 crn 2) rain.

ventimation both sides

1" (2.5 cm)

10 in.2(64.5 cm 2)

ventilation both sides

5" (12.7 crn) max.

"_' (12.7 crn) max.

On freestanding models, the model/serial number rating plate is

located inside the grill cabinet on the right-hand cabinet side.

See the following illustration.

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

If codes permit and a separate ground wire is used, it is

recommended that a qualified electrician determine that the

ground path is adequate.

Check with a qualified electrician if you are not sure whether the

grill is properly grounded.

A 120-volt, 60-Hz, AC-only, 15-amp, fused electrical supply is

required.

It is recommended that aseparate circuit servicing only this grill

be provided.

A. Model/serial number pla te

On built-in models, the model/serial number rating plate is

located on the right-hand side of the grill. See the following

illustration.

A. Model/serial number plate

Recommended Ground Method

The outdoor grill, when installed, must be electrically grounded in

accordance with local codes or, in the absence of local codes,

with the National Electrical Code ANSI/NFPA 70, or Canadian

Electrical Code, CSA C22.1.

Copies of the standards listed above may be obtained from:

CSA International

8501 East Pleasant Valley Rd.

Cleveland, Ohio 44131-5575

National Fire Protection Association

One Batterymarch Park

Quincy, Massachusetts 02269

S ...............................

A .... "......................

A. 3-prong ground plug

B.3-prong polarized type outdoor outlet

C. Ground prong

............. : :_;,.e_]! @ _.e l I't:,,_

Explosion Hazard

Use a new CSA international approved "outdoor"

gas supply line.

Securely tighten all gas connections.

if connected to LP, have a qualified person make sure

gas pressure does not exceed 11" (28 cm) water

column.

Examples of a qualified person include:

licensed heating personnel,

authorized gas company personnel, and

authorized service personnel.

Failure to do so can result in death, explosion, or fire.

Gas Conversion:

No attempt shall be made to convert the grill from the gas

specified on the model/serial rating plate for use with a different

gas type without consulting the serving gas supplier. The

conversion kits specified must be used.

Gas Pressure Regulator

The gas pressure regulator supplied with this grill must be used.

The inlet (supply) pressure to the regulator should be as follows

for proper operation:

LP Gas:

Operating pressure: 11" (27.9 cm) WCP

Inlet (supply) pressure: 11" to 14" (27.9 cm to 35.5 cm) WCP

Natural Gas:

Operating pressure: 4" (10.2 cm) WCP

Inlet (supply) pressure: 7" to 14" (17.8 cm to 35.5 cm) WCP

maximum.

Contact local gas supplier if you are not sure about the inlet

(supply) pressure.

Burner Requirements for High Altitude

Input ratings shown on the model//serial rating plate are for

elevations up to 2,000 ft (609.6 m).

For elevations above 2,000 ft (609.6 m), ratings are reduced at a

rate of 4% for each 1,000 ft (304.8 m) above sea level. Orifice

conversion is required. See "Assistance or Service" section to

order.

Gas Supply Line Pressure Testing

Testing above 1/2psi (3.5 kPa) or 14" (35.5 cm) WCP (gauge):

The grill and its individual shutoff valve must be disconnected

from the gas supply piping system during any pressure testing of

that system at test pressures greater than 1/2psig (3.5 kPa).

Testing below 1/2psi (3.5 kPa) or 14" (35.5 cm) WCP (gauge) or

lower:

The grill must be isolated from the gas supply piping system by

closing its individual manual shutoff valve during any pressure

testing of the gas supply piping system at test pressures equal to

or less than 1/2psig (3.5 kPa).

Observe all governing codes and ordinances.

IMPORTANT: This installation must conform with all local codes

and ordinances. In the absence of local codes, installation must

conform with American National Standard, National Fuel Gas

Code ANSI Z223.1 -latest edition or CAN/CGA B149.1 -latest

edition.

IMPORTANT: Grill must be connected to a regulated gas supply.

Refer to the model/serial rating plate for information on the type

of gas that can be used. If this information does not agree with

the type of gas available, check with your local gas supplier.

20 Ib LP Gas Fuel Tank

This grill is equipped for use with a 20 Ib LP gas fuel tank (fuel

tank not supplied). A gas pressure regulator/hose assembly is

supplied.

It is also design-certified by CSA International for local LP gas

supply or for Natural gas with appropriate conversion.

A. Gaspressure regulator/hose assembly

The 20 Ib LP gas fuel tank must be mounted and secured.

1. Open the 20 Ib LP gas fuel tank drawer.

2. Place the 20 Ib LP gas fuel tank bottom collar into the

mounting hole in the tank tray.

3. Tighten the locking screw against the bottom collar of the

20 Ib LP gas fuel tank to secure.

! ,

B C

A.Locking screw

B.Mounting hole

C.Bottom collar

4. Slide tank drawer back into the cabinet.

Local LP Gas Supply

IMPORTANT: The gas installation must conform with local

codes, or in the absence of local codes, with the National Fuel

Gas Code, ANSI Z223.1/NFPA 54 - latest edition. The qualified

LP gas technician shall provide the LP gas supply to the selected

grill location in accordance with the National Fuel Gas Code,

ANSI Z223.1/NFPA 54 and local codes.

C ............................_"!.........................

D==_

A. Grill gaspipe

B. NewANSI Z21.54 certified gray hose

C.Rear of grifl

D. Tolocal LP gas supply

Natural Gas Conversion

Conversion must be made by a qualified gas technician. The

qualified Natural gas technician shall provide the Natural gas

supply to the selected grill location in accordance with the

National Fuel Gas Code ANSI Z223.1/NFPA 54 - latest edition,

and local codes. For conversion to Natural gas, the Natural gas

conversion kit must be used.

IMPORTANT: The gas installation must conform with local

codes, or in the absence of local codes, with the National Fuel

Gas Code, ANSI Z223.1/NFPA 54 - latest edition.

To convert to Natural gas, the Natural Gas Conversion Kit Part

Number W10118098 must be used. Follow instructions included

with the kit.

f_ ............................L,,!.........................

%..

A. Grill gas pipe

B. New ANSI Z21.54 certified gray hose

C. Rear of grifl

D. To Natural gas supply

Natural Gas

Built-in grill models are equipped for use with Natural gas. They

are design-certified by CSA International for LP (propane or

butane) gases with appropriate conversion.

Built-in models are set for Natural gas use and have a pressure

regulator with 1/2"female pipe threads.

............................D ..........C

A. Grill gas pipe

B. New CSA International approved

"outdoor" flexible gas supply line

C. Rear of grifl

D. To Natural gas supply

The supply line shall be equipped with an approved shutoff valve.

This valve should be located in the same area as the grill and

should be in a location that allows ease of opening and closing.

Do not block access to the shutoff valve. The valve is for turning

on or shutting off gas to the grill.

A. Gas supply line

B. Shutoff valve "open" position

C. To grill

LP Gas Conversion Using a Local LP Gas Supply

Conversion must be made by a qualified person. A qualified

Natural gas technician shall provide the LP gas supply to the

selected grill location in accordance with the National Fuel Gas

Code ANSI Z223.1/NFPA 54 - latest edition, and local codes.

To convert to LP gas, the LP Gas Conversion Kit Part Number

W10118099 must be used. Follow instructions included with kit.

m,/S

.................................g

A. Grill gas pipe

B. New CSA International approved

"outdoor" flexible gas supply line

C. Rear of grill

D. To local LP gas supply

LP Gas Conversion Using a 20 Ib LP Gas Fuel Tank

To convert to LP gas, the LP Gas Conversion Kit Part Number

W10118099 must be used. Follow instructions included with kit.

A 20 Ib LP gas fuel tank must be purchased separately.

INSTALLATION

INSTRUCTIONS

.., ]- O. Ido (.))::ili

Excessive Weight Hazard

Use two or more people to move and install grill.

Failure to do so can result in back or other injury.

1. Unpack grill. Remove all packaging materials and remove grill

from wooden skid.

2. Move grill into desired outdoor location.

3. Open the hood.

Remove Packaging Material Inside the Grill

1. Cut the tiedowns holding the grates together.

2. Remove condiment shelf, warming shelf and grill grates from

inside the grill and remove packaging material.

3. Remove foam block and wrap from inside the grill.

I/ ..............

A. Foam block

B. Foam wrap

4. Replace the grill grates.

5. Place warming shelf on brackets as shown.

A. Warming sheff brackets

B. Warming sheff

Attach condiment shelf (on some models) to the inside of the

left cabinet door.

A.Attachment holes

B.Condiment sheff

Dispose of/recycle all packaging material.

Make Gas Connection

Explosion Hazard

Securely tighten all gas connections.

if connected to LP, have a qualified person make sure

gas pressure does not exceed 11" (28 cm) water

column.

Examples of a qualified person include:

licensed heating personnel,

authorized gas company personnel, and

authorized service personnel.

Failure to do so can result in death, explosion, or fire.

If converting to Natural gas, see conversion kit requirements in

the "Gas Supply Requirements" section. Follow instructions

included with kit.

LP Gas:

IMPORTANT: A 20 Ib LP gas fuel tank must be purchased

separately.

IMPORTANT: The gas pressure regulator/hose assembly

supplied with the grill must be used. Replacement gas pressure

regulator/hose assembly specific to your model, is available from

your outdoor grill dealer.

To Install the 20 Ib LP Gas Fuel Tank:

1. Open the 20 Ib LP gas fuel tank drawer.

2. Place the 20 Ib LP gas fuel tank bottom collar into the

mounting hole in the tank tray

3. Tighten the locking screw against the bottom collar of the

20 Ib LP gas fuel tank to secure.

B C

A. Locking screw

B. Mounting hole

C. Bottom collar

Screw the gas pressure regulator/hose assembly to the 20 Ib

LP gas fuel tank as shown.

Pipe-joint compounds suitable for use with Natural gas

must be used. Do not use TEFLON ®ttape.

...............................................g

C ............................................................

A. 20 Ib LP gas fuel tank

B. Gas pressure regulator/hose assembly

5. Turn on the gas supply. Wait a few minutes for gas to move

through the gas line.

6. Test all connections by brushing on an approved

noncorrosive leak-detection solution. Bubbles will show a

leak. Correct any leak found.

7. Go to "Check and Adjust the Burners" section.

If Converted to Natural Gas

Explosion Hazard

Use a new CSA International approved "outdoor"

gas supply line.

Securely tighten all gas connections.

Failure to do so can result in death, explosion, or fire.

This installation must conform with local codes and ordinances.

In the absence of local codes, installations must conform with

either the National Fuel Gas Code ANSI Z223.1, or CAN/CGA-

B149.1 Natural Gas and Propane installation code.

Copies of the standards listed above may be obtained from:

CSA International

8501 East Pleasant Valley Rd.

Cleveland, Ohio 44131-5575

National Fire Protection Association

One Batterymarch Park

Quincy, Massachusetts 02269

1. Make gas connections.

A combination of pipe fittings must be used to connect the

grill to the existing gas line.

• If local codes permit, use an outdoor flexible stainless

steel tubing gas connector, design-certified by CSA

International, to connect the grill to the rigid gas supply

line. A %" diameter line is recommended. Using a wrench

to tighten, connect the gas supply to the grill. Use pipe-

joint compound on all non-flared male threads. Do not

kink or damage the flexible connector when moving the

grill.

A. Grill gas pipe

B. New ANSI Z21.54 certified gray hose

C. Rear of grifl

D. To Natural gas supply

Open the manual shutoff valve in the gas supply line. The

valve is open when the handle is parallel to the gas pipe.

A. Closed valve

B. Open valve

3. Test all connections by brushing on an approved

noncorrosive leak-detection solution. Bubbles will show a

leak. Correct any leak found.

4. Go to "Check and Adjust the Burners" section.

Plug in Grill

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

1. Plug into a grounded 3-prong outlet.

1-®TEFLON is a registered trademark of E.I. Du Pont De Nemours and Company.

Make Gas Connection

Excessive Weight Hazard

Use two or more people to move and install grill.

Failure to do so can result in back or other injury.

Unpack grill. Remove all packaging materials and remove grill

from carton.

Move grill close to desired outdoor location.

Open the hood.

Remove Packaging Material Inside the Grill

1. Cut the tiedowns holding the grates together.

2. Remove rotisserie skewer (on some models), warming shelf

and grill grates from inside the grill and remove packaging

material.

3. Remove foam block and wrap from inside the grill.

A .....

_ ......

":..\>\//_/-p_//'_................. _-"- .... ...............

Z:o.............

A. Foam block

B. Foam wrap

4. Replace the grill grates.

5. Place warming shelf on brackets as shown.

A. Warmingsheff brackets

B. Warmingsheff

Install rotisserie mounting bracket using 2 screws.

A.2bracket screws

B.Rotisseriebracket

Dispose of/recycle all packaging material.

NOTE: If grill has been converted to LP gas, follow instructions in

"If Converting to LP Gas" at the end of this section.

Fire Hazard

Do not use grill near combustible materials.

Do not store combustible materials near grill.

Doing so can result in death or fire.

Natural Gas Use

This installation must conform with local codes and ordinances.

In the absence of local codes, installations must conform with

either the National Fuel Gas Code ANSI Z223.1 - latest edition, or

CAN/CGA-B149.1 Natural Gas and Propane installation code.

1. Place grill into outdoor enclosure, but leave enough room in

back to connect to gas supply and electrical plug-in.

Explosion Hazard

Use a new CSA International approved "outdoor"

gas supply line.

Securely tighten all gas connections.

Failure to do so can result in death, explosion, or fire.

Make gas connections.

A combination of pipe fittings must be used to connect the

grill to the existing gas line.

If local codes permit, use an outdoor flexible stainless

steel tubing gas connector, design-certified by CSA

International, to connect the grill to the rigid gas supply

line. A %" diameter line is recommended. Using a wrench

to tighten, connect the gas supply to the grill. Use pipe-

joint compound on all non-flared male threads. Do not

kink or damage the flexible connector when moving the

grill.

• Pipe-joint compounds suitable for use with Natural gas

must be used. Do not use Teflon ®tape.

............................D

A. Grill gas pipe

B. New CSA International approved

"outdoor" flexible gas supply line

C. Rear of grill

D. To Natural gas supply

Open the manual shutoff valve in the gas supply line. The

valve is open when the handle is parallel to the gas pipe.

A. Closed valve

B. Open valve

4. Test all connections by brushing on an approved

noncorrosive leak-detection solution. Bubbles will show a

leak. Correct any leak found.

Plug in Grill

1. This built-in outdoor grill comes with a 5,000 mAmp power

transformer plug assembly for the grill lights and igniter. Plug

in the single-prong plug in the receptacle on the left

underside of the grill.

A. Single-prong plug

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

2. Plug into a grounded 3-prong outlet.

3. Gently slide grill completely into outdoor enclosure.

4. Now go to the "Check and Adjust the Burners" section.

If Converting to LP Gas

Explosion Hazard

Use a new CSA international approved "outdoor"

gas supply line.

Securely tighten all gas connections.

if connected to LP, have a qualified person make sure

gas pressure does not exceed 11" (28 cm) water

column.

Examples of a qualified person include:

licensed heating personnel,

authorized gas company personnel, and

authorized service personnel.

Failure to do so can result in death, explosion, or fire.

IMPORTANT: A 20 Ib LP gas fuel tank must be purchased

separately.

IMPORTANT: The gas pressure regulator/hose assembly

supplied with the conversion kit must be used. Replacement gas

pressure regulator/hose assembly specific to your model, is

available from your outdoor grill dealer.

To Install the 20 Ib LP Gas Fuel Tank:

1. Install the 20 Ib LP gas fuel tank into the compartment below

the grill.

2. Screw the gas pressure regulator/hose assembly to the

20 Ib LP gas fuel tank as shown.

A. 20 Ib LP gas fuel tank

B. Gaspressure regulator/hose assembly

3. Turn on the gas supply. Wait a few minutes for gas to move

through the gas line.

4. Test all connections by brushing on an approved

noncorrosive leak-detection solution. Bubbles will show a

leak. Correct any leak found.

5. Go to "Check and Adjust the Burners" section.

The burners are tested and factory-set for most efficient

operation. However, variations in gas supply and other conditions

may make minor adjustments to air shutter or low flame setting

necessary.

It is recommended that a qualified person make burner

adjustments.

NOTE: The rotisserie burner cannot be adjusted.

Checking and adjusting the grill burner flames requires removing

the grate and sear plates.

Burner Flame Characteristics

The flames of the grill burners and side burners (on some models)

should be blue and stable with no excessive noise or lifting (LP

gas flames will have a slightly yellow tip). A yellow flame indicates

not enough air. If flame is noisy or lifts away from the burner, there

is too much air. Some yellow tips on flames when the burner is

set to HI setting are acceptable as long as no carbon or soot

deposits appear.

Check that burners are not blocked by dirt, debris, insect nests,

etc. and clean as necessary. If they are clean, adjust air shutters

as needed.

IMPORTANT: Before adjusting air shutters, let burners cool

completely.

To Adjust:

1. Light grill using information inthe "Outdoor Grill Use" section.

2. Observe flame to determine which burners need adjustment

and how the flame is acting.

3. Turn off the valve and wait until grill and burners cool

completely.

4. Remove grill grates and sear plates.

Remove the 2 screws that hold the burner in place. Remove

gas burner from the grill.

A.2 screws

If flame is yellow (not enough air), turn air shutter adjustment

screw counterclockwise.

If flame is noisy or lifts away from burner (too much air), turn

air shutter adjustment screw clockwise.

A.Air shutteradjustment screw

Adjustment should be made clockwise or counterclockwise

from V8"(3.2 mm) to V4"(6.4 mm).

7. Replace gas burner, sear plates and grates.

8. Light grill using information in the "Outdoor Grill Use" section.

See "Burner Flame Characteristics."

Low Flame Adjustment

If flame goes out on the "LO" setting, the low flame setting must

be adjusted.

1. Turn off the valve and wait until grill and burners are cool.

2. Remove grill grates and sear plates.

3. Light grill using information in the "Outdoor Grill Use" section.

4. Turn burner to its lowest setting and remove knob.

5. Hold valve stem with pliers and insert a small flat-blade

screwdriver into the shaft.

6. Watch the flame and slowly turn the screwdriver

counterclockwise.

7. Adjust flame to minimum stable flame.

A. Valve stem

B. Small flat-blade screwdriver

C. Priers

8. Replace the control knob and turn off the burner.

9. Repeat steps 3 through 8 for each burner if needed.

10. Replace the sear plates and grates after the burners have

cooled.

OUTDOOR GRILL USE

This manual covers several different models. The grill you have purchased may have some or all of the features listed. The locations and

appearances of the features shown here may not match those of your model.

Control Panel

A B C D E F G H

ROTISSERIE LEFT CENTER RIGHT SEAR ROTISSERIE FRONT REAR

BURNER BURNER BURNER BURNER BURNER BURNER BURNER BURNER

[_ _ _ L'GHTS _ _ _-I

FTm o FTTT1 u

LIGHTING INSTRUCTIONS:

31 IF IGNITION DOES NOT IMMeDIATeLY TAKE

P_cE,_UR__ _URN_RVALWHAND.S

TO'roFmWAIT5_INUT_SANDRE.AT

TH_ LIGHTING _OC_DURE 2

A. Left rotisserie burner control knob

B. Left grill burner control knob

C. Center grill burner control knob

D. Right grill burner control knob

E. Electronic grill display

F Sear burner control knob

G. Right rotisserie burner control knob

H. Front side burner control knob

I. Rear side burner control knob

Explosion Hazard

Do not store fuel tank in a garage or indoors.

Do not store grill with fuel tank in a garage or indoors.

Failure to follow these instructions can result in death,

explosion, or fire.

Fire Hazard

Do not use grill near combustible materials.

Do not store combustible materials near grill.

Doing so can result in death or fire.

Food Poisoning Hazard

Do not let food sit for more than one hour before or

after cooking.

Doing so can result in food poisoning or sickness.

Inspect the LP Gas Fuel Tank Supply Hose

Inspect the gas pressure regulator/hose assembly before each

use.

1. Open the right-hand drawer and slide 20 Ib LP gas fuel tank

out.

2. Inspect the entire gas pressure regulator/hose assembly for

cuts, abrasions, or excessive wear.

3. If necessary, replace the gas pressure regulator/hose

assembly before using the grill.

Contact the dealer and use only replacement hoses specified for

use with the grill.

A. Gas pressure regulator/hose assembly

Prepare the Gas Supply

1. Open the hood completely. Do not light burners with the hood

closed.

2. Make sure control knobs are turned to OFE The drip pan

must be in place and pushed all the way to the back.

3. Strike the match to light it.

4. Guide the lit match between the grill grate and one of the

slots in the sear plate.

A. Drip pan

5. Push in and turn the burner knob to LITE/HI for the burner

closest to the lit match. The burner will light immediately.

When burner is lit, turn knob to desired setting.

Turn the Gas Supply On

1. For freestanding outdoor grills using a 20 Ib LP gas fuel tank:

Slowly open the tank valve.

NOTE: If flow limiting device activates, your grill may not

light. If your grill does light, the flames will be low and will not

heat properly. Turn tank valve and all control knobs off and

wait 30 seconds. After shutting off the tank, very slowly open

tank valve and wait 5 seconds before lighting.

2. For outdoor grills using gas supply source other than 20 Ib LP

gas fuel tank:

Open the manual shutoff valve in the gas supply line. The

valve is open when the handle is parallel to the gas pipe.

Lighting the Grill and Infrared Sear Burner

1. Do not lean over the grill.

2. Select the burner you want to light. Push in and turn the grill

burner control knob to LITE/HI, while continuing to hold it in.

3. You will see the igniter glow. When burner is lit, release the

knob. Turn knob to desired setting.

4. Repeat for each of the other burners as needed.

IMPORTANT: If burner does not light immediately, turn the

burner knob to OFF and wait 5 minutes before relighting.

Manually Lighting Main Grill and Infrared Sear Burners

1. Do not lean over the grill.

2. Remove the manual lighting extension (see following

illustration) and attach a match to the split ring.

Freestanding grills - right-

hand cabinet door

Built-in grills - right-hand side

flange

6. Repeat steps 2 through 5 for each main burner.

7. Remove match and replace manual lighting extension inside

the cabinet drawer.

IM PORTANT:

If burner does not light immediately, turn the burner knob to OFF

and wait 5 minutes before relighting.

If any burners do not light after attempting to light them manually,

contact the KitchenAid Customer eXperience Center. See the

"Assistance or Service" section.

Infrared grilling produces intense heat which quickly sears the

meat. Searing locks in flavor and juices while allowing the outer

surface to absorb smoke and food aroma that is produced as

grease and drippings are vaporized by the burner. The result is a

crisp, flavorful outside with a tender, juicy inside.

• Preheat the infrared sear burner for 5 minutes.

• Ensure that meats are fully thawed and that all excess fat is

trimmed away prior to grilling.

• Leave the burner set to HI when placing food on the grill to

sear.

• Use the sear burner to sear meat 1 to 2 minutes on each side,

then move the meat to the main grill cooking surface to finish

grilling to the desired doneness.

NOTE: View is shown with grates removed. Grates are

to be in place when using the infrared sear burner.

Us is 8 .......

Burn Hazard

Do not let the burner flame extend beyond the edge of

the pan.

Doing so can result in burns.

Lighting the Side Burner

1. Remove the side burner cover. Do not light burners with the

cover on.

2. Do not lean over the grill.

3. Push in and turn the control knob to LITE/HI and hold in.

5. Push in and turn the burner knob to LITE/HI for the burner

closest to the lit match. The burner will light immediately.

When burner is lit, turn knob to desired setting.

6. Repeat steps 2 through 5 for each burner.

7. Remove match and replace manual lighting extension inside

the cabinet drawer.

IM PORTANT:

If burner does not light immediately, turn the burner knob to OFF

and wait 5 minutes before relighting.

If any burners do not light after attempting to light them manually,

contact the KitchenAid Customer eXperience Center. See the

"Assistance or Service" section.

4. You will see the igniter glow. When burner is lit, release the

knob. Turn knob to desired setting.

5. Repeat for each of the other burners as needed.

IMPORTANT: If burner does not light immediately, turn the

burner knob to OFF and wait 5 minutes before relighting.

Manually lighting the side burner

Do not lean over the grill.

Remove the manual lighting extension (see following

illustration) and attach a match to the split ring.

Portable grills - right-hand

cabinet drawer

Built-in grills - right-hand side

flange

Strike the match to light it.

Guide the match to the burner you wish to light.

A. Rotisserie motor

B. Spit rod

C. Rotisserie fork

D. Rotisserie burner

For best cooking results, do not use main grill burners when

using the rotisserie.

The rotisserie system is designed to cook food from the rear

using intense, searing infrared heat.

NOTE: To avoid product damage when not using the rotisserie,

remove motor and store indoors. Remove spit rod and forks.

Store out of reach of children.

To Use:

1. Remove warming shelf.

2. Mount rotisserie motor on the grill's mounting bracket.

Position it securely into support bracket slots. Plug single-

prong plug 500 mAmp transformer assembly into rotisserie

motor.

A. Rotisserie motor

B.Single-prong power cord

La page charge ...

KitchenAid KBNU367TSS00 Le manuel du propriétaire

Marque: KitchenAid

Modèle: KBNU367TSS00

Catégorie: Barbecues

Taper: Le manuel du propriétaire

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: KitchenAid KBNU367TSS00 Owner's manual

KitchenAid KBNU367TSS00 Le manuel du propriétaire

Ce manuel convient également à

KitchenAid KBNU367TSS00 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents