Sanyo DC-UB1475M Manuel utilisateur

Marque: Sanyo

Modèle: DC-UB1475M

Catégorie: Lecteur CD

Taper: Manuel utilisateur

INSTRUCTION MANUAL

Micro Component System

DC-UB1475M

ENGLISH

ESPAÑOL

PORTUGUÊS

8 - 16

17 - 25

26 - 34

FRANÇAIS

35 - 43

IURQWFRYHULQGG 

1475XEfcover.indd 11475XEfcover.indd 1 2008-7-18 13:19:082008-7-18 13:19:08

CAUTION – USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN

MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.

ACHTUNG – WENN ANDERE ALS DIE HIER SPEZIFIZIERTEN BEDIENUNGS- ODER JUSTIEREINRICHTUNGEN BENÜTZT ODER

ANDERE VERFAHRENS-WEISEN AUSGEFÜHRT WERDEN, KANN DIES ZU GEFÄHRLICHER STRAHLUNGSEXPOSITION FÜHREN.

ATTENTION – L’EMPLOI D’ORGANES DE COMMANDE OU DE RÉGLAGE, OU L’EXÉCUTION DE PROCÉDURES, AUTRES QUE CEUX

SPÉCIFIÉS DANS LE MODE D’EMPLOI, PEUT PROVOQUER UNE EXPOSITION DANGEREUSE AU RAYONNEMENT.

OPGELET – HET GEBRUIK VAN REGELAARS OF HET MAKEN VAN AFSTELLINGEN E.D. DIE NIET IN DEZE GEBRUIKSAANWIJZING

ZIJN BESCHREVEN KAN LEIDEN TOT SCHADELIJKE STRALINGEN.

VARNING! OM APPARATEN ANVÄNDS PÅ ANNAT SÄTT ÄN VAD SOM BESKEIV I DENNA BRUKSANVISNING, KAN ANVÄNDAREN

UTSÄTTAS FÖR OSYNLIG LASERSTRÅLNING, SOM ÖVERSKRIDER GRÄNSEN FÖR LASERKLASS 1.

VAROITUS! LAITTEEN KÄYTTÄMINEN MUULLA KUIN TÄSSÄ KÄYTTÖOHJEESSA MAINITULLA TAVALLA SAATTAAALTISTAA

KÄYTTÄJÄN TURVALLISUUSLUOKAN 1 YLITTÄVÄLLE NÄKYMÄTTÖMÄLLE LASERSÄTEILYLLE.

CAUTELA – L’USO DI COMANDI, AGGIUSTAMENTI O PROCEDIMENTI DIVERSO DA QUELLO QUI SPECIFICATO PUÒ DAR LUOGO AD

ESPOSIZIONE A RADIAZIONI PERICOLOSE.

PRECAUCION – EL USO DE CONTROLES O AJUSTES, O PROCEDIMIENTOS DE OPERACION DIFERENTES DE LOS ESPECIFICADOS

EN ESTE DOCUMENTO RESULTARAN EN EXPOSICION PELIGROSA A LA RADIACION.

CUIDADO – O USO DOS CONTROLOS OU AJUSTES OU DESEMPENHOS DE PROCEDIMENTOS OUTROS QUE NÃO OS

ESPECIFICADOS NAS INSTRUÇÕES DE OPERAÇÃO PODEM RESULTAR EM PERIGOSAS EXPOSIÇÕES À RADIAÇÃO.

This set complies with the EMC Directive 2004/108 and with the LVD Directive 2006/95.

Dieses Gerät entspricht der EMC-Direktive 2004/108 und der LVD-Direktive 2006/95.

Cet appareil est en conformité avec la directive EMC 2004/108 et avec la directive BT 2006/95.

Dit toestel is in overeenstemming met EMC-richtlijn 2004/108 en met LVD-richtlijn 2006/95.

Detta set uppfyller EMC-direktivet 2004/108 och Lågspänningsdirektivet 2006/95.

Questo set aderisce alle direttive EMC 2004/108 e alle direttive LVD 2006/95.

Este aparato cumple con la Directiva EMC 2004/108 y con la Directiva LVD 2006/95.

Este conjunto satisfaz a Directiva EMC 2004/108 e a Directiva LVD 2006/95.

CAUTION - INVISIBLE LASER RADIATION WHEN OPEN AND

INTERLOCKS DEFEATED. AVOID EXPOSURE TO BEAM.

ADVARSEL - USYNLIG LASER STRÅLING VED ÅBNING, NÅR

SIKKERHEDSAFBRYDERE ER UDE AF FUNKTION, UNDGÅ UDS ÆTTELSE

FOR STRÅLING.

VARNING - OSYNLIG LASER STRÅLNING NÄR DENNA DEL ÄR ÖPPNAD

OCH SPÄRR ÄR URKOPPLAD. STRÅLEN ÄR FARLIG.

VORSICHT - UNSICHTBARE LASERSTRAHLUNG TRITT AUS, WENN

DECKEL GEÖFFNET UND WENN SICHERHEITSVERRIEGELUNG

ÜBERBRÜCKT IST. NICHT, DEM STRAHL AUSSETZEN.

VARO - AVATTAESSA JA SUOJALUKITUS OHITETTAESSA OLET ALTTIINA

NÄKYMÄTTÖMÄLLE LASERSÄTEILYLLE. ÄLÄ KATSO SÄTEESEEN.

1475XEFront.indd 11475XEFront.indd 1 2008-7-18 15:49:412008-7-18 15:49:41

[ENGLISH]

Your SANYO product is designed and manufactured with high quality

materials and components which can be recycled and reused.

This symbol means that electrical and electronic equipment, at their end-

of-life, should be disposed of separately from your household waste.

Please dispose of this equipment at your local community waste collection/

recycling centre.

In the European Union there are separate collection systems for used

electrical and electronic products.

Please help us to conserve the environment we live in!

[DEUTSCH]

Ihr SANYO Produkt wurde entworfen und hergestellt mit qualitativ

hochwertigen Materialien und Komponenten, die recycelt und

wiederverwendet werden können.

Dieses Symbol bedeutet, daß elektrische und elektronische Geräte am

Ende ihrer Nutzungsdauer von Hausmüll getrennt entsorgt werden sollen.

Bitte entsorgen Sie dieses Gerät bei Ihrer örtlichen kommunalen

Sammelstelle oder im Recycling Centre.

In der Europäischen Union gibt es unterschiedliche Sammelsysteme für

Elektrik- und Elektronikgeräte.

Helfen Sie uns bitte, die Umwelt zu erhalten, in der wir leben!

[FRANÇAIS]

Votre produit Sanyo est conçu et fabriqué avec des matèriels et des

composants de qualité supérieure qui peuvent être recyclés et réutilisés.

Ce symbole signifie que les équipements électriques et électroniques en

fin de vie doivent être éliminés séparément des ordures ménagères.

Nous vous prions donc de confier cet équipement à votre centre local de

collecte/recyclage.

Dans l’Union Européenne, il existe des systèmes sélectifs de collecte pour

les produits électriques et électroniques usagés.

Aidez-nous à conserver l’environnement dans lequel nous vivons !

Les machines ou appareils électriques et électroniques contiennent

fréquemment des matières qui, si elles sont traitées ou éliminées de

manière inappropriée, peuvent s’avérer potentiellement dangereuses pour

la santé humaine et pour l’environnement.

Cependant, ces matières sont nécessaires au bon fonctionnement de

votre appareil ou de votre machine. Pour cette raison, il vous est demandé

de ne pas vous débarrasser de votre appareil ou machine usagé avec vos

ordures ménagères.

[NEDERLANDS]

Sanyo producten zijn ontwikkeld en gefabriceerd uit eerste kwaliteit

materialen, de onderdelen kunnen worden gerecycled en weer worden

gebruikt.

Het symbool betekent dat de elektrische en elektronische onderdelen

wanneer deze vernietigd gaan worden, dit separaat gebeurt van het

normale huisafval.

Zorg ervoor dat het verwijderen van de apparatuur bij de lokaal erkende

instanties gaat gebeuren.

In de Europese Unie wordt de gebruikte elektrische en elektronische

apparatuur bij de daarvoor wettelijke instanties aangeboden.

Alstublieft help allen mee om het milieu te beschermen.

[SVENSKA]

Din SANYO produkt är designad och tillverkad av material och

komponenter med hög kvalitet som kan återvinnas och återanvändas.

Denna symbol betyder att elektriska och elektroniska produkter, efter

slutanvändande, skall sorteras och lämnas separat från Ditt hushållsavfall.

Vänligen, lämna denna produkt hos Din lokala mottagningstation för avfall/

återvinningsstation.

Inom den Europeiska Unionen finns det separata återvinningssystem för

begagnade elektriska och elektroniska produkter.

Vänligen, hjälp oss att bevara miljön vi lever i!

[ITALIANO]

Il vostro prodotto SANYO è stato costruito da materiali e componenti di

alta qualità, che sono riutilizzabili o riciclabili.

Prodotti elettrici ed elettronici portando questo simbolo alla fine dell’uso

devono essere smaltiti separatamente dai rifiuti casalinghi.

Vi preghiamo di smaltire questo apparecchio al deposito comunale.

Nell’Unione Europea esistono sistemi di raccolta differenziata per prodotti

elettrici ed

elettrici

elettronici.

ed elettronici.

Aiutateci a conservare l’ambiente in cui viviamo!

[ESPAÑOL]

Los productos SANYO están diseñados y fabricados con materiales y

componentes de alta calidad, que pueden ser reciclados y reutilizados.

Este símbolo significa que el equipo eléctrico y electrónico, al final de su

ciclo de vida, no se debe desechar con el resto de residuos domésticos.

Por favor, deposite su viejo “televisor” en el punto de recogida de residuos

o contacte con su administración local.

En la Unión Europea existen sistemas de recogida específicos para

residuos de aparatos eléctricos y electrónicos.

Por favor, ayúdenos a conservar el medio ambiente!

[PORTUGUÊS]

O seu produto SANYO foi concebido e produzido com materiais e

componentes de alta qualidade que podem ser reciclados e reutilizados.

Este símbolo significa que o equipamento eléctrico e electrónico no final

da sua vida útil deverá ser descartado separadamente do seu lixo

doméstico.

Por favor, entregue este equipamento no seu ponto local de recolha/

reciclagem.

Na União Europeia existem sistemas de recolha separados para produtos

eléctricos e electrónicos usados.

Por favor, ajude-nos a conservar o ambiente em que vivemos!

[SUOMI]

SANYO-tuotteesi on suunniteltu ja valmistettu korkealaatuisista

materiaaleista ja osista, joita voidaan kierrättää ja käyttää uudelleen.

Tämä symboli tarkoittaa, että sähkölaitteet ja -osat on niiden käyttöiän

päättyessä hävitettävä erillään kotitalouden jätteistä.

Toimita laite paikalliseen jätteenkeräys/kierrätyskeskukseen.

Euroopan unionin alueella on erilliset keräysjärjestelmät käytetyille

sähkölaitteille ja

sähkölaitteille

-osille.

ja -osille.

Auta meitä suojelemaan ympäristöä jossa elämme!

1475XEFront.indd 21475XEFront.indd 2 2008-7-18 15:49:412008-7-18 15:49:41

24 23 22

Fig. 1

1475XEFront.indd 31475XEFront.indd 3 2008-7-18 15:49:422008-7-18 15:49:42

Fig. 2

Fig. 3

FM aerial

Antenne FM

Antena aérea de FM

Antena de FM

AM loop aerial

Antenne-cadre AM

Antena AM de cuadro

Antena AM de quadro

L ch speaker

Enceinta gauche

Altavoz del canal

izquierdo

Altifalante do canal

esquerdos

R ch speaker

Haut-parleur droit

Altavoz del canal

derecho

Altifalante do canal

direito

Red

Black

Red

To an AC outlet

Vers une prise secteur

A un tomacorriente de CA

A uma tomada de CA

1475XEFront.indd 41475XEFront.indd 4 2008-7-18 15:49:422008-7-18 15:49:42

USB memory device

Dispositif de mémoire USB

Dispositivo de memoria USB

Dispositivo de memória USB

Removing the SD card

Retrait de la carte SD

Cómo sacar la tarjeta SD

Ta ut SD-kortet

Video/Auxiliary equipment

Équipement vidéo/auxiliaire

Equipo auxiliar de video

Video/Equipmento Auxiliar

Fig. 5

Screws (not supplied)

Vis (non fournies)

Tornillos (no suministrados)

Parafusos (não incluídos)

Fig. 4

1475XEFront.indd 51475XEFront.indd 5 2008-7-18 15:49:422008-7-18 15:49:42

Two R03/AAA batteries (not supplied)

Deux piles de format R03/AAA (non fournies)

Dos pilas R03/AAA (no incluídas)

Duas pilhas R03/AAA (não fornecidas)

Within approx. 7 meters

Environ 7 mètres

Dentro de approxi-

madamente 7 metros

Dentro de 7 metros aprox.

Remote sensor

Détecteur de télé-

commande

Sensor remoto

Fig. 6

Fig. 7

Fig. 8 Fig. 9

Fig. 10

1475XEFront.indd 61475XEFront.indd 6 2008-7-18 15:49:422008-7-18 15:49:42

Side A

Face A

Lado A

Side B

Face B

Lado B

Break out tab A for side A.

Briser la languette A pour la face A.

Romper lengüeta A del lado A.

Parta a patilha A para o lado A.

Break out tab B for side B.

Briser la languette B pour la face B.

Romper lengüeta B del lado B.

Parta a patilha B para o lado B.

Fig. 11

543

1.Cotton swab

2.Capstan

3.Pinch roller

4, 5.Heads

Fig. 12

Fig. 13

1. Bastoncillo

2. Cabrestante

3. Rodillo de presión

4, 5. Cabeza

1. Cotonete

2. Rolete

3. Rolete de arrasto

4, 5. Cabeça

1. Coton-tige

2. Cabestan

3. Galet presseur

4, 5. Téte

1475XEFront.indd 71475XEFront.indd 7 2008-7-18 15:49:432008-7-18 15:49:43

ENGLISH

PRECAUTIONS

- The apparatus shall not be exposed to dripping or splashing.

- Do not use where there are extremes of temperature (below 5 °C or

exceeding 35 °C) or where direct sunlight may strike it.

- Because of the CD players extremely low noise and wide dynamic

range, there might be a tendency to set the volume on the ampliﬁ er

unnecessarily high. Doing so may produce an excessively large out-

put from the ampliﬁ er which could damage your speakers.

- Sudden changes in the ambient temperature may cause

condensation to form on the optical lens inside the unit. If this

happens, take out the disc, leave the unit for about 1 hour, and then

proceed to operate.

- The systems speakers use powerful magnets. Do not place time

pieces, credit cards, cassette tapes or video tapes, etc. near the

speakers.

- Do not install this equipment in a confined space, such as a

bookcase or built in cabinet.

- No objects ﬁ lled with liquids, such as vases, shall be placed on the

apparatus.

- The ventilation should not be impeded by covering the ventilation

openings with items, such as newspapers, table-cloths, curtains etc.

- No naked ﬂ ame sources, such as lighted candles, should be placed

on the apparatus.

- To be completely disconnect the power input, the mains plug of

apparatus shall be disconnect from the mains.

- The rating label is located on the rear of cabinet.

- A t t e n t i o n s h o u l d b e d r a w n t o t h e environmental aspects

of battery disposal.

- Battery shall not be exposed excessive heat such as sunshine, ﬁ re

or the like.

- MAINS plug or an appliance coupler is used as the disconnect

device, the disconnect device shall remain readily operable.

- Minimum distance around the apparatus for sufﬁ cient ventilation.

CONNECTIONS

Note:

- Do not connect the mains lead to an AC outlet until all connections

have been made.

- The system is not completely disconnected from the AC power

when the

/ON button is set to the

(standby) position.

Speakers (Fig.3)

Connect the red speaker wire to the red terminal (+) and the other wire

to the black terminal (-) .

Aerial

FM aerial

Extend the aerial wire as straight as possible and, while listening to

the sound from the system, secure it in a position which yields minimal

distortion and noise.

AM loop aerial (Fig.4)

Assemble the loop aerial as shown in Fig. 4. Unwind the aerial wires,

then connect them to the AM LOOP terminals. Place the loop aerial in a

position which yields the best AM reception, or attach it to a wall or other

surface.

Note:

To minimize noise, the speaker, mains and any other leads should not

come close to the FM aerial lead and AM loop aerial. Do not place the

aerial leads close to the system.

Headphones

Connect stereo headphones (not supplied) to the PHONES socket

for monitoring or for private listening. The speakers are automatically

disconnected when headphones are connected.

- Excessive sound pressure from earphones and headphones can

cause hearing loss.

USB device and SD card (Fig.5)

Connect the USB device into the USB port.

Inster the SD card into the SD slot with the correct direction.

Video/Auxiliary equipment (Fig.5)

Connect the audio cable (not supplied) from the audio output socket of a

video/auxiliary equipment to the LINE IN socket.(Stereo Mini Plug: ø3.5)

1475XEEnglish.indd 81475XEEnglish.indd 8 2008-7-18 13:18:152008-7-18 13:18:15

CONTROLS (Fig.1)

1. USB port (USB)

2. Line in socket (LINE IN)

3. Stop/PTY search button (STOP/PTY

)

4. Skip/Search/File select/Tuning button (- TUN/FILE +,

)

5. Band select button (BAND)

6. Folder/Channel select button (FOLDER/CHANNEL)

7. Function button (FUNCTION)

8. Remote sensor (IR)

9. Power button (

/ON)

10. Display

11. CD Compartment (OPEN/CLOSE

)

12. Bass expander button (DBBS)

13. RDS/Play mode button (RDS/PLAY MODE)

14. Program/Clock button (PROGRAM/CLOCK)

15. Timer button (TIMER)

16. Volume control (VOLUME)

17. Play/Pause button (PLAY/PAUSE

)

18. SD card loading slot (SD)

19. Cassette holder

20. Tape buttons cover (OPEN

)

21. Pause button (

)

22. Stop/Eject button (

)

23. Fast forward button (

)

24. Rewind button (

)

25. Play button (

)

26. Record button (

)

REMOTE CONTROL

Controls (Fig.2)

1. Power/Stand by button (

/STANDBY)

2. Mute button (MUTE)

3. Timer button (TIMER)

4. Program/Clock button (PROGRAM/CLOCK)

5. RDS/Play mode button (RDS/PLAY MODE)

6. PTY search/Stop button (PTY SEARCH /

)

7. Display button (DISPLAY)

8. Skip/Search/File select/Tuning button (

)

9. Play/Pause button (

)

10. FM mode button (FM MODE)

11. Volume button (VOLUME -, +)

12. Bass expander button (DBBS)

13. Number button (0,1~9)

14. Sleep button (SLEEP)

15. Sound mode select button (SOUND)

16. Folder/Channel select button (FOLDER/CHANNEL +, -)

17. Tuner function/Band select button (TUN/BAND)

18. Function button (FUNCTION)

Number buttons (0, 1-9)

Example:

Tuner/Audio CD

To select No. 3, press 3.

To select No. 10, press 1, then press 0.

MP3/WMA/USB/SD card

To select No. 3, press 3.

To select No. 10, press 1, then press 0.

To select No. 126, press 1, 2, then press 6.

Inserting batteries (Fig. 6)

Note:

Always remove battery if the remote control is not to be used for a

month or more. Battery within the unit may leak and cause damage.

Remote control range (Fig. 7)

The buttons on the remote control perform similar functions to similarly

marked buttons on the front panel.

ADJUSTING THE CLOCK

When the unit is ﬁ rst connected to the AC power line, the display blinks

“00:00” dimly.

Example: To set “6:30”.

First, press the

/ON button to turn the power on.

1. Press the PROGRAM/CLOCK button for at least 2 seconds. “-- --:--

--”(when the first time setting) or the current time appears on the

display.

2. Press the PROGRAM/CLOCK button again. After “SET CLOCK”

appears on the display, the time system appears. Press the

button to select “24HR”.

3. Press the PROGRAM/CLOCK button. The hours display blinks.

4. Press the

button to set the “hours”.

5. Press the PROGRAM/CLOCK button. The minutes display blinks.

6. Press the

button to set the “minutes”.

7. Press the PROGRAM/CLOCK button to complete the setting, the

original function returns.

- The time can be set accurately by pressing the PROGRAM/

CLOCK button when a time signal is heard.

- To display the clock during operations, press the PROGRAM/

CLOCK button at least 2 seconds. After a few seconds, the original

display returns.

- If a power failure occurs or the mains lead is disconnected, the clock

display blinks. Reset the time again.

1475XEEnglish.indd 91475XEEnglish.indd 9 2008-7-18 13:18:152008-7-18 13:18:15

BEFORE OPERATION

Turning the power on and off

Press the

/STANDBY button to turn on the power, the display lights up

and “HELLO” appears brieﬂ y.

To turn the power off, press the

/STANDBY button again. “Good bye”

appears brieﬂ y, then the clock display remains lit dimly.

- When the mains lead is connected to the AC outlet, the unit will re-

spond to commands from the remote controller.

Adjusting the volume

Press the VOLUME + or - button. The volume level appears by numbers

(VOL MIN ~ VOL MAX) on the display.

Dynamic Bass Boost System

Press the DBBS button to enhance the bass sound. “BBS ON” appears

on the display.

Press the button again, “BBS OFF” appears. Normal sound resumes.

Selecting the sound mode (Remote control only)

Press the SOUND button to select the sound mode matching the music

to be listened to.

CLASSIC: Classical music, etc.

ROCK: Rock music, etc.

POP: Pops, etc.

JAZZ: Jazz, etc.

FLAT: Normal

Selecting the mute mode (Remote control only)

Press the MUTE button once. “MUTE” blinks on the display, the sound

is mute.

Press the button again, “MUTE” disappear. Normal sound resumes.

WHAT TO DO IF ...

If the operation of the unit or display is not normal,

1. Press the

/STANDBY button to turn off the power.

2. Turn on the power and resume the operation.

CD PLAY

Use compact discs bearing the symbol shown in Fig. 8. In addition to

conventional 12 cm CDs, this system can be used to play 8 cm CDs

without an adapter.

1. Press the FUNCTION button to select “CD” function.

2. Press the CD compartment lid (OPEN/CLOSE

portion) to open it,

“OPEN” appears.

3. Place the disc with the label facing up on the disc turntable (Fig. 9).

(Place only one disc at a time.)

4. Press the CD compartment lid (OPEN/CLOSE

portion) again

to close it. “READING” blinks for several seconds, then the total

number of tracks and total playing time appear.

Note:

If a badly scratched disc is loaded or if the disc is loaded with the

label facing downward, “NO DISC” appears. If this occurs, load the

disc correctly or replace the damaged disc.

5. Press the

button. Play starts from the ﬁ rst track.

The current track number and elapsed playing time are displayed.

6. Press the

button to end disc play.

When the last track has been played, the player stops automatically.

Notes on handling compact discs

- Do not expose the disc to direct sunlight, high humidity or high

temperatures for extended periods of time.

- Discs should be returned to their cases after use.

- Do not apply paper or write anything on the disc surface.

- Handle the disc by its edge. Do not touch the playing surface (glossy

side).

- Fingerprints and dust should be carefully wiped off the playing

surface of the disc with a soft cloth.

Wipe in a straight motion from the centre to the outside of the disc.

- Never use chemicals such as record cleaning sprays, antistatic

sprays or ﬂ uids, benzene or thinner to clean compact discs.

To start play from the desired track

Select the track by using the

button, then press the

button.

Temporarily stopping play

Press the

button, elapsed playing time blinks on the display. To

resume play, press the button again.

Skip play

To skip to track 6 while track 3 is playing, press the

button

repeatedly until “06” appears (in the track section) on the display. To skip

back to track 3 while track 6 is playing, press the

button repeatedly

until “03” appears.

- The number buttons on the remote control can also be used for skip

play. To skip to track 6 while one track is playing, press 0, then 6.

Search (forward/reverse)

If the

button is pressed during play, the player will search at

high speed in the forward or reverse direction while the button is being

pressed. When the button is released, normal play will continue.

This instruction manual explains the various functions of this unit

using the remote control. The buttons on the main unit perform

similar functions to similary marked buttons on the remote control.

1475XEEnglish.indd 101475XEEnglish.indd 10 2008-7-18 13:18:162008-7-18 13:18:16

Changing a programme

To add a new track to a programme:

1. In the stop mode, press the PROGRAM/CLOCK button repeatedly

until the programme number blinks on the display.

2. Select a track as explained above.

3. Press the PROGRAM/CLOCK button.

To change a track:

1. In the stop mode, press the PROGRAM/CLOCK button repeatedly

until the track number to be replaced is displayed.

2. Select a track as explained above.

3. Press the PROGRAM/CLOCK button.

Note:

Programmed details cannot be partially deleted or inserted.

MP3/WMA CD OPERATION

This unit can play the CD-R/RW that has recorded music data, MP3 or

WMA(Window Media Audio) ﬁ les. Before playing MP3/WMA CD, please

read the following.

MP3/WMA CD information

- MP3/WMA CD is the disc that standardized by ISO9660, its file

name must have the extension letters, “.MP3” or “.mp3”/ “.WMA” or

“.wma”.

- Standard, sampling frequency, and the bit rate:

MP3 ﬁ les:

MPEG-1 Audio

32 kHz, 44.1 kHz, 48 kHz

32 kbps ~ 320 kbps (constant bit rate or variable bit rate)

WMA ﬁ les:

WMA version 7, 8 and 9

32 kHz, 48 kbps ~ 64 kbps

44.1 kHz, 48 kbps ~ 192 kbps

48 kHz, 128 kbps ~ 192 kbps

WMA9 professional files, WMA9 lossless files or DRM (copyright

protection) ﬁ les cannot be played.

- In this model, recommend recording setting for a high-quality sound

is 44.1 kHz of sampling frequency and 128 kbps of constant bit rate.

If files are recorded in other bit rate (for example: 320kbps) or in

variable bit rate, track-jump may sometimes happen according to

recording conditions.

- The directory and file names of the MP3/WMA CD must be

corresponded to the ISO standardized ﬁ les.

- Single-session disc can be played. As for multi-session disc, only

the ﬁ rst session can be played.

- This unit can recognize up to 99 folders or 999 ﬁ les per disc.

- This unit can recognize up to 8 directory trees per disc.

- Some MP3/WMA CD may not be played in the recorded order.

- Music section in “CD Extra” can be played.

Notes on disc writing method

There are three basic methods for writing to a CD: “Track-at-Once”,

“Disc-at-once”, and “Packet Writing”.

Music ﬁ les recorded by “Track-at-Once” or “Disc-at-Once” can be played

on the unit. (Note: The unit cannot play the music files added with

“Trackat-Once”.)

Music ﬁ les recorded by “Packet Writing” cannot be played.

Limitations on the display

Available letters for display are the following: capital alphabets of A

through Z, numbers of 0 through 9, and _ (underline).

Repeat / Random play

Press the RDS/PLAY MODE button repeatedly before or during play to

select various play modes available.

Each time the button is pressed, the play mode changes as shown

below:

- Random play will not function during programmed play.

PROGRAMMED PLAY

Up to 40 tracks on a disc can be programmed for play in any order.

- First, select “CD” function and load a disc that you want to

programme.

- The tracks must be programmed in the stop mode.

- The same track can be programmed more than once.

1. Press the PROGRAM/CLOCK button. The program number “01”

blinks on the display.

2. Select a track by using the

button.

3. Press the PROGRAM/CLOCK button. The program number “02”

blinks on the display.

4. Repeat steps 2 - 3 to programme additional tracks.

5. Press the

button to start programmed play.

When all programmed tracks have been played, the player stops

automatically.

- The programme contents are retained in memory.

- Any attempt to programme more than 40 tracks will result in “FULL”

being displayed and discontinuation of the programming.

- To cancel programmed play, press the

button twice during playing,

“PROG CLEAR” appears.

Checking the programme

Each time the PROGRAM/CLOCK button is pressed in the stop mode,

the programmed details sequentially appear on the display.

“

”appears

(Repeat one track)

“

ALL” appears

(Repeat all tracks)

“

” appears

(Play all tracks randomly)

Released

(Normal play mode)

1475XEEnglish.indd 111475XEEnglish.indd 11 2008-7-18 13:18:172008-7-18 13:18:17

MP3 CD directory sample:

Play order: song01

song02

...

song14

Folder number F01

There is no MP3 file.

The unit skips it.

song01.mp3

song02.mp3

song03.mp3

song04.mp3

song05.mp3

douc01.doc

photo01.jpg

song06.mp3

song07.mp3

song08.mp3

song09.mp3

song10.mp3

song11.mp3

song12.mp3

song13.mp3

song14.mp3

MP3 CD

F01 albumF01

F02 albumF02

F04 albumF03

F03 albumF04

Note:

- Some MP3/WMA CDs cannot be played depending on the recording

conditions.

- The CD-R/RW that has no music data or non-MP3 ﬁ les cannot be

played.

- Do not make an empty folder. It may not work correctly.

Basic playback

1. Load the MP3/WMA CD.

“READING” blinks, then the total folder number and total track

number appear on the display.

Example: For an MP3 and WMA mixed CD.

2. Press the FOLDER/CHANNEL + or - button to select the desired

folder.

3. Press the

button to select the desired track.

4. Press the

button to start play.

Note:

For the MP3 and WMA mixed CD, both “WMA” and “MP3” remain on the

display except playing mode.

If current playing track is MP3 ﬁ le, only “MP3” appears.

If current playing track is WMA ﬁ le, only “WMA” appears.

Display selection

The ID3-Tag is an information ﬁ eld for MP3/WMA. Album name, music

title and artist name can be stored into the tag. This unit shows this

information.

Press the DISPLAY button on the remote control during play.

Each time the button is pressed, the display changes and scrolls over on

the display in the following sequence:

ALBUM( album name)

ARTIST(artist name)

TITLE(music title)...

- After the information scrolls over, the playing display returns.

Folder/File selection

1. In stop mode or during play, press the FOLDER/CHANNEL + or -

button to select the desired folder.

2. Press the

button to select desired track. Then press the

button to start play.

In playing mode, play starts automatically.

Repeat / Random play

Press the RDS/PLAY MODE button repeatedly before or during play to

select various play modes available.

Each time the button is pressed, the play mode changes as shown

below:

“

”appears

(Repeat selected single

MP3/WMA ﬁ le)

“

ALL” appears

(Repeat all MP3/WMA ﬁ les or

programmed MP3/WMA ﬁ les)

“

” appears

(Play all MP3/WMA

ﬁ les randomly)

Released

(Normal play mode)

“ FOLDER” appears

(Repeat all MP3/WMA files

in the folder)

- Random play will not function during programmed play.

PROGRAMMED PLAY

1. In stop mode, press the PROGRAM/CLOCK button.

2. Press the FOLDER/CHANNEL + or - button to select desired folder.

3. Press the

button to select desired ﬁ le.

4. Press the PROGRAM/CLOCK button.

5. Repeat 2 ~ 4 steps to programme additional tracks.

6. Press the

button to start programmed play.

7. Press the

button at any time to stop the programmed play.

- To cancel programmed play, press the

button twice during play.

Note:

Other various playback operations, please refer to the descriptions in

CD PLAY (page 10).

1475XEEnglish.indd 121475XEEnglish.indd 12 2008-7-18 13:18:182008-7-18 13:18:18

USB MEMORY DEVICE OPERATION

IMPORTANT INFORMATIONS:

- Copyright protection ﬁ les cannot be played back.

- Copyright protection ﬁ les on the USB memory device are skipped

automatically when played back.

- Recommended use:

Flash memory type USB memory player

Not recommended:

Hard Disc Memory type USB player

- Some ﬂ ash memory player does not play successfully with this

unit.

Before use

Connect the USB memory device to the USB port of the mains unit

correctly as shown in Fig.5.

- Some USB memory devices cannot be used.

- This unit can recognize only MP3 or WMA (Window Media Audio)

ﬁ les.

- This unit can recognize up to 999 ﬁ les or 99 folders in USB memory

device.

However, some cannot be recognized depending on the folder

structure.

- It may take more time for the reading operation depending on the

recording condition.

- Please refer to “MP3/WMA CD information” on the page 11.

Basic playback

1. Press the FUNCTION button to select the “USB” function.

“READING” appears, then the total folders and ﬁ les numbers appear

on the display.

- If the connection of the USB memory device is failed or the

unit cannot recognize the USB memory device, “PLS INSERT

USB” appears.

- If there is no MP3/WMA ﬁ le in the USB memory device, or just

some empty folders in the USB memory device, “NO FILE”

appears.

2. Press the FOLDER/CHANNEL + or - to select the desired folder.

3. Press the

button to select the desired ﬁ le.

4. Press the

button to start play.

5. Press the

button to stop play.

When the last ﬁ le has been played, the player stops automatically.

Other various playback operations

Please refer to the descriptions in MP3/WMA CD OPERATION (Page

12).

Removing the USB device

1. Press the

button, then switch to other function.

2. Remove the USB device.

Note:

Do not disconnect the USB device during playing, recording. If do, the

data may be damaged.

SD CARD OPERATION

IMPORTANT INFORMATIONS

- Copyright protection ﬁ les cannot be played back.

- Copyright protection files on an SD card are skipped

automatically when played back.

Before use

- Load an SD card (not supplied) with the music ﬁ les (MP3 or WMA).

(Fig.5)

- This unit doesn't support the SD card and RS-MMC card which

capacity is over 2G.

- Down load the music files (MP3 or WMA) into the SD card (not

supplied) from your PC.

- This unit can recognize up to 999 ﬁ les or 99 folders in SD card.

Note:

Some cards cannot be used depending on its structure.

Basic playback

1. Press the FUNCTION button to select the “CARD” function.

“READING” appears, then the total folders and ﬁ les numbers appear

on the display.

- If the insertion of the SD card is failed or the unit cannot

recognize the SD card, “PLS INSERT CARD” appears.

- If there is no MP3/WMA file in the SD card, or just some

empty folders in the SD card, “NO FILE” appears.

2. Press the FOLDER/CHANNEL + or - to select the desired folder.

3. Press the

button to select the desired ﬁ le.

4. Press the

button to start play.

5. Press the

button to stop play.

When the last ﬁ le has been played, the player stops automatically.

Other various playback operations

Please refer to the descriptions in MP3/WMA CD OPERATION (Page

12).

Removing the SD card

1. Press the

button, then switch to other function.

2. Push the card slightly into the slot to release.

3. Pull it out. (Fig.5)

Notes on handling SD cards

- Do not expose the SD card to direct sunlight, humidity or high

temperatures for extended periods of time.

- SD cards should be returned to their cases after use.

- Do not try to decompose the SD cards.

- Keep the original SD label and never try to apply any new paper on

it.

- Do not touch the metal terminal part of the SD card.

Metal terminal part

(Back)

1475XEEnglish.indd 131475XEEnglish.indd 13 2008-7-18 13:18:182008-7-18 13:18:18

LISTENING TO TAPES

1. Press the FUNCTION button to select “TAPE” function.

“TAPE” appears.

2. Pull the OPEN

portion to open the cassette button cover.

3. Press the

button to open the cassette holder.

4. Load the cassette (Fig. 10). After loading the cassette, push the

cassette holder back into position.

5. Press the

button to begin play.

6. Press the

button to stop play at any time. Press it again to

remove the cassette.

When the end of the tape has been reached, automatic stop will be

activated.

Note:

- Use the normal tape (TYPE 1).

- Endless tapes cannot be used.

- Do not use C-100 (or longer) tapes. They may jam in the

mechanism.

Pause

Press the

button to temporarily stop playback or recording. Press it

again to resume operation.

Fast forward and rewind

Press the

button. When the desired location has been

reached, press the

button.

Automatic stop system

At the end of the tape while recording or playing back, the cassette deck

stops automatically and the buttons are released.

This system does not work in fast forward and rewind operation. Be sure

to press the

button when the end of the tape has been reached.

Example (When using C-60 tape):

Press the

button after approximately 2 minutes have elapsed under

fast forward and rewind operation.

LISTENING TO THE RADIO

Automatic/Manual tuning

1. Press the FUNCTION button to select “TUNER” function.

2. Press the TUN/BAND button to select FM or AM. The radio

frequency appears on the display.

3. Automatic tuning

Press the

button for at least 1 second to tune in a

station. The unit will scan down or up the band and receive the next

receivable station. Press the button again to continue.

Manual tuning

Press the

button brieﬂ y until the desired frequency is

displayed.

To preset stations

Up to 30 stations for FM band, 10 stations for AM band can be preset.

1. Tune in the station to be preset as described above.

2. Press the PROGRAM/CLOCK button. The preset channel number

blinks on the display.

3. Press the FOLDER/CHANNEL + or - button to select a channel be

preset.

4. Press the PROGRAM/CLOCK button

- In this example, “89.80 MHz” FM station is preset on FM

channel 9.

5. Repeat steps above to add more preset stations.

When presetting a new station, the previous preset station is cleared.

Listening to preset stations

1. Press the TUN/BAND button to select FM or AM.

2. Press the FOLDER/CHANNEL + or - button to select the desired

channel number.

- The number buttons on the remote control can also be used.

To receive FM stereo broadcasts (Remote control

only)

“ ” appears when an FM stereo broadcast is received. If not, press

the FM MODE button to turn the “ ” indication on.

- If the signal from an FM stereo station is weak and reception is poor,

press the FM MODE button to change to the monaural mode. The

reception may be improved, but the sound will be monaural.

1475XEEnglish.indd 141475XEEnglish.indd 14 2008-7-18 13:18:192008-7-18 13:18:19

Listening to FM station with RDS

RDS (Radio Data System) permits FM stations to send additional

signals with the regular programme signals. For example, the stations

send their station names and information about what type of broadcast

programmes, such as sports or music, etc.

Note:

- Some FM stations do not provide RDS service.

- RDS may not work correctly if the signal strength is weak.

- RDS is not available for AM broadcasts.

Selecting the RDS display mode

1. When tuning in an FM station which provides the RDS service, the

“PS” RDS mode is set automatically, the station name and “

”

appear on the display.

2. Press the RDS/PLAY MODE button repeatedly to select “PS”, “PTY”,

“RT”, “CT” or “Frequency”. Related informations will appears.

PS (Programme Service)

“PS” appears on the display, then station name is displayed. If no PS

signal is received, “NO PS” appears brieﬂ y, then station frequency is

displayed.

PTY (Programme Type)

“PTY” appears, then broadcast programme type is displayed. If no

PTY signal is received, “NO PTY” appears, then station name or

station frequency is displayed.

RT (Radio Text)

“RT” appears, then text messages sent by station will be displayed.

If no RT signal is received, “NO TEXT” appears.

CT (Clock Time)

“CT” appears, then the clock time sent by station will be displayed. If

no CT signal is received, “NO CT” appears.

Frequency

Station frequency appears.

On characters displayed

When the display shows PS, PTY, RT or CT signals:

- The display shows upper case letters only.

- The display cannot show accented letters:

For example, “A” may represent accented “A’s” like “Á”, “À”, “Ã”, “Â”,

“Å” and “Ä”.

To search a station by PTY (Programme Type) codes

A particular programme type broadcast can be located by specifying the

PTY codes.

1. Press the PTY SEARCH button, “PTY SEL” blinks on the display.

2. Press the

button to select the desired PTY code.The

code changes as shown below:

NEWS: News

AFFAIRS: Current affairs

INFO: Information

SPORT: Sport

EDUCATE: Education

DRAMA: Drama

CULTURE: Culture

SCIENCE: Science

VARIED: Varied

POP M: Pop music

ROCK M: Rock music

MOR M: Middle of the road music

(easy-listening)

LIGHT M: Light classics

CLASSICS: Serious classics

OTHER M: Other music

WEATHER: Weather

FINANCE: Finance

CHILDREN: Children’s programmes

SOCIAL R: Social affairs

RELIGION: Religion

PHONE IN: Phone in

TRAVEL: Travel

LEISURE: Leisure

JAZZ M: Jazz music

COUNTRY: Country music

NATIONAL: National music

OLDIES M: Oldies music

FOLK M: Folk music

DOCUMENT: Documentary

3. Press the PTY SEARCH button. The unit will scan up or down the

band and stop when it ﬁ nds a broadcast of the selected PTY code,

then tunes into that station and “

” appears.

- To continue searching after the ﬁ rst stop, repeat steps 1~3 again.

- If no broadcast is found, “NOT FOUND” appears, then the original

station is heard.

- To cancel searching, press the PTY SEARCH button once.

LISTENING TO OTHER SOURCES (Fig.5)

1. Press the FUNCTION button to select “AUX”.

2. Follow the instructions supplied with the video/auxiliary equipment.

RECORDING

Recording copyright material without permission of the copyright owners

is usually an infringement. If you wish to re-record copyright material,

permission from the copyright owner is necessary. SANYO does not

approve of, and cannot be held responsible for, any unlawful use of this

machine.

Recording from discs, USB or SD

(Synchronous recording)

1. Load a blank cassette.

2. Select “CD” or “USB” or “SD” function.

3. Load the disc or insert an USB memory device or an SD card to be

recorded.

- Select the track number if required.

- For programmed recording, programme the material in

advance (as described under “Programmed play”).

4. Press the

button. The

button is engaged simultaneously and

CD recording starts.

- When you want to record music as you listen, press the

button. Recording starts automatically from the beginning of

the track.

5. Press the

button to stop recording.

When the end of the tape is reached, the deck and the playback of CD

or USB memory device or SD card stop automatically.

Recording from the tuner

1. Load a blank cassette.

2. Tune in the radio button to be recorded.

3. Press the

button to start recording.

4. Press the

button to stop recording.

When beat is heard

Beat (a high-pitched noise) may sometimes be heard during the recording

of radio broadcasts. If this occurs, set the BEAT CANCEL switch (the

rear of the unit) to 1 or 2 position the reduces the level of the beat noise.

Safeguards against accidental erasure

Accidental erasure can be prevented by breaking out the tabs on the end

of the cassette tape (where the tape is not exposed) using a screwdriver

or similar implement (Fig. 11).

If a tab is broken out in error and you wish to re-record the tape, simply

block the tab hole using adhesive tape and the tape can be used for

recording again.

1475XEEnglish.indd 151475XEEnglish.indd 15 2008-7-18 13:18:202008-7-18 13:18:20

TIMER OPERATION

Wake-up timer

Set the on and off time, the unit will turn on and start the selected

function automatically at the on time, and will turn off when the off time

arrives.

The timer will function every day unless it is released.

Preparations

Make absolutely sure that the clock is set to the correct time before

setting the timer.

- Prepare the source to be used.

- Adjust the tuner or band of radio if choosing “TUNER”.

- Place the disc in advance if choosing “CD”.

- Connect the USB memory device in advance if choosing “USB”.

- Insert the SD card if choosing “CARD”.

For example:Waking up at 7:30 every day and listening to the CD until

8:15.

1. Turn on the power and press the TIMER button. “SELECT

SOURCES” scrolls on the display.

2. Press the FUNCTION button to select “CD”.

3. Press the TIMER button. Volume level blinks on the display. Press

the VOLUME + or - button to select the volume.

4. Press the TIMER button. “SET ON TIMER” scrolls on the display.

5. Press the TIMER button again. The hour section of the preset on-

time blinks on the display.

6. Press the

button to set the hours.

7. Press the TIMER button. The minute section blinks on the display.

8. Press the

button to set the minutes.

9. Press the TIMER button. “SET OFF TIMER” scrolls on the display.

10. Repeat above steps 5-8 to set off time.

11. Press the TIMER button to complete the setting. Original function

retuns.Then turn off the power. The clock time appears and

remains lit.

Note:

- The preset function starts when the timer on-time arrives.

The volume increases gradually to the preset level.

- When the timer off-timer arrives, the power turns off and the timer is

set to the standy mode. Timer operation repeats everyday.

To release the timer

In power on mode, press the TIMER button once, disappears.

Or in power off mode, press the

/STANDBY button to turn on the unit.

disappears.

Sleep timer (Remote control only)

The sleep timer automatically switches off the power after a preset time

has elapsed. There are 9 time periods available: 90, 80, 70, 60, 50, 40,

30, 20, and 10 minutes.

Press the SLEEP button repeatedly to select the desired sleep time.

After several seconds, the original display returns, “

” remains lit.

To release the sleep timer while in operation

Press the SLEEP button repeatedly to select “OFF”, “

” disappears

from the display. The timer is also released if the power is switched off.

MAINTENANCE

Cleaning the tape heads (Fig. 12)

To ensure continued high performance, use cotton swab to clean the

heads, pinch roller and capstan of the decks after about every 10 hours

of use. If the dirt persists, soak the swab in a little methylated spirit or

head cleaning ﬂ uid and then clean.

Cleaning the CD player lens

The lens should never be touched. If dust is on the lens, blow it off using

a camera lens blower (Fig. 13). (Consult your dealer.)

Cleaning the unit

Clean the outside of the unit with a clean soft cloth, moistened with

lukewarm water. Do not use benzene, thinner or alcohol since they will

mar the ﬁ nish of the surfaces.

1475XEEnglish.indd 161475XEEnglish.indd 16 2008-7-18 13:18:212008-7-18 13:18:21

FRANÇAIS

PRÉCAUTIONS

- Cet appareil ne doit pas être exposé à l’égouttement ou aux

éclaboussures.

- Ne l’utilisez pas dans des endroits ayant des températures extrêmes

(moins de 5°C ou plus de 35°C) ou sous la lumière directe du soleil.

- En raison du bruit extrêmement bas et de la vaste portée dynamique

du lecteur CD, on peut avoir tendance à mettre le volume de l’

ampliﬁ cateur trop haut inutilement. Le faire peut produire une sortie

excessive de l’ampliﬁ cateur et endommager vos haut-parleurs.

- Les changements soudains de la température ambiante peuvent

créer une condensation sur la lentille optique à l’intérieur de l’

appareil. Si cela se produit, enlevez le disque et attendez environ

une heure avant d’utiliser l’appareil.

- Les haut-parleurs du système utilisent des aimants puissants.

Éloignez les montres, cartes de crédit, cassettes ou bandes vidéo,

etc., des haut-parleurs.

- N’installez pas cet équipement dans un endroit confiné, telle une

bibliothèque ou un cabinet encastré.

- Aucun objet contenant du liquide, comme un vase, ne doit être placé

sur l’appareil.

- La ventilation ne doit pas être entravée par la couverture des oriﬁ

ces de ventilation avec des articles, tels que des journaux, nappes

de table, rideau etc.

- Aucune source de flamme nue, telle que bougie allumée, ne doit

être placée sur l'appareil.

- Pour couper complètement l’alimentation, la prise de secteur de l’

appareil doit être débranchée du secteur.

- L’étiquette de caractéristiques nominales est située au dos de l’

unité.

- Une attention particulière doit être donnée aux aspects

environnementaux de la mise au rebut des piles.

- Les piles ne doivent pas être exposées à une chaleur excessive,

comme les rayons du soleil, le feu ou quelque chose de semblable.

- Quand la prise de SECTEUR ou un coupleur d'appareils est utilisé

comme appareil de sectionnement, l'appareil de sectionnement doit

rester prêt à être utilisé.

- Des distances minimales autour de l'appareil pour une aération

sufﬁ sante.

CONNEXIONS

Remarque:

- Ne branchez pas le cordon d’alimentation à une prise CA avant que

toutes les connexions ne soient faites.

- Le système n’est pas complètement déconnecté de l’alimentation

CA lorsque la touche

/ON est réglée à la position

(mode veille).

Haut-parleurs (Fig.3)

Connectez le ﬁ l rouge du haut-parleur au terminal rouge (+) et l’autre ﬁ l

au terminal noir (-).

Antenne

Antenne FM

Déroulez le ﬁ l d’antenne aussi droit que possible et, tout en écoutant le

son du système, placez-le dans la position offrant la distorsion et le bruit

minimaux.

Antenne cadre AM (Fig.4)

Assemblez l'antenne cadre comme illustré dans la Fig.4. Déroulez

le fil de l'antenne, puis connectez-le à la borne AM LOOP. Placez

l'antenne cadre dans une position qui offre la meilleure réception AM ou

attachezla à un mur ou une autre surface.

Remarque:

Pour réduire le bruit, le haut-parleur, le cordon d’alimentation et tout

autre fil ne doivent pas être à proximité du fil d'antenne FM et de l’

antenne cadre AM. Ne placez pas les ﬁ ls d’antenne près du système.

Écouteurs

Branchez les écouteurs stéréo (non fournis) à la prise PHONES pour la

surveillance ou l'écoute privée. Les haut-parleurs sont automatiquement

déconnectés quand les écouteurs sont connectés.

- Une pression sonore excessive au niveau des écouteurs ou du

casque audio peut entraîner des pertes d’audition.

Périphérique USB et carte SD (Fig.5)

Branchez le périphérique USB au port USB.

Insérez la carte SD dans la fente SD dans le sens approprié.

Equipement vidéo/auxiliaire (Fig.5)

Connectez le câble audio (non fourni) de la prise de sortie audio d'un

équipement vidéo/auxiliaire à la prise LINE IN. (Mini ﬁ che stéréo : ø3.5)

1475XEFrench.indd 171475XEFrench.indd 17 2008-7-18 13:19:242008-7-18 13:19:24

COMMANDES (Fig.1)

1. Port USB (USB)

2. Prise d’entrée de ligne (LINE IN)

3. Bouton arrêt/PTY (STOP/PTY

)

4. Bouton Sauter/Rechercher Sélection de ﬁ chier/ Syntonisation

(- TUN/FILE +,

)

5. Sélecteur de bande (BAND)

6. Bouton de sélection du dossier/canal (FOLDER/CHANNEL)

7. Bouton de fonction (FUNCTION)

8. Capteur à distance (IR)

9. Bouton d’alimentation (

/ON)

10. Afﬁ chage

11. Compartiment CD (OPEN/CLOSE

)

12. Bouton d'ampliﬁ cation des basses fréquences (DBBS)

13. Bouton de mode RDS/Lecture (RDS/PLAY MODE)

14. Bouton de programme/d’horloge (PROGRAM/CLOCK)

15. Bouton de minuterie (TIMER)

16. Contrôle du volume (VOLUME)

17. Bouton Lecture/Pause (PLAY/PAUSE

)

18. Fente de chargement de carte SD (SD)

19. Support de cassette

20. Couvercle des boutons de cassette (OPEN

)

21. Bouton pause (

)

22. Bouton Arrêt/Ejecter (

)

23. Bouton Avance rapide (

)

24. Bouton Rembobiner (

)

25. Bouton Lecture (

)

26. Bouton Enregistrer (

)

TELECOMMANDE

Commandes (Fig.2)

1. Bouton d'alimentation/mise en veille (

/STANDBY)

2. Bouton Silence (MUTE)

3. Bouton de minuterie (TIMER)

4. Bouton de programme/d’horloge (PROGRAM/CLOCK)

5. Bouton de mode RDS/Lecture (RDS/PLAY MODE)

6. Bouton recherche PTY/arrêt (PTY SEARCH /

)

7. Bouton Afﬁ chage (DISPLAY)

8. Bouton Sauter/Rechercher/Sélection de ﬁ chier/Syntonisation

(

)

9. Bouton Lecture/Pause (

)

10. Bouton mode FM (FM MODE)

11. Bouton de volume (VOLUME -, +)

12. Bouton d'ampliﬁ cation des basses fréquences (DBBS)

13. Boutons numériques (0,1~9)

14. Bouton de mise en veille (SLEEP)

15. Bouton de sélection du mode sonore (SOUND)

16. Bouton de sélection du dossier/canaux (FOLDER/CHANNEL +, -)

17. Bouton de sélection de bande/Fonction Syntonisation (TUN/BAND)

18. Bouton de fonction (FUNCTION)

Boutons numériques (0, 1-9)

Exemple:

Syntoniseur/CD audio

Pour sélectionner N° 3, appuyez sur 3.

Pour sélectionner N° 10, appuyez sur 1 puis sur 0.

MP3/WMA/USB/carte SD

Pour sélectionner N° 3, appuyez sur 3.

Pour sélectionner N° 10, appuyez sur 1 puis sur 0.

Pour sélectionner N° 126, appuyez sur 1, 2 puis sur 6.

Insertion des piles (Fig. 6)

Remarque:

Retirez toujours les piles si vous prévoyez ne pas utiliser la

télécommande pour un mois ou plus. Les piles laissées peuvent fuir et l’

endommager.

Portée de la télécommande (Fig. 7)

Les boutons sur la télécommande effectuent une fonction similaire à

celle des boutons marqués sur le panneau avant.

REGLAGE DE L'HORLOGE

Lors de la première connexion de l’unité à la ligne d’alimentation CA, l’

afﬁ chage clignote faiblement avec “00:00”.

Exemple: Pour régler “6:30”.

D’abord, appuyez sur le bouton

/ON pour mettre l’alimentation sous

tension.

1. Appuyez sur le bouton PROGRAM/CLOCK pendant au moins 2

secondes. “-- --:-- --”(lors du premier réglage d’horloge) ou l’heure

actuelle apparaissent sur l’afﬁ chage.

2. Appuyez de nouveau sur le bouton PROGRAM/CLOCK. Après que

“SET CLOCK” apparaît sur l’affichage, l’heure système apparaît.

Appuyez sur le bouton

pour sélectionner “24HR”.

3. Appuyez sur le bouton PROGRAM/CLOCK. L’afﬁ chage de l’heure

clignote.

4. Appuyez sur le bouton

pour régler les “hours”.

5. Appuyez sur le bouton PROGRAM/CLOCK. L’afﬁ chage des minutes

clignote.

6. Appuyez sur le bouton

pour régler les “minutes”.

7. Appuyez sur le bouton PROGRAM/CLOCK pour compléter ce

réglage, la fonction originale revient.

- L’heure peut être réglée avec précision en appuyant sur

le bouton PROGRAM/CLOCK lorsqu’un signal horaire est

entendu.

- Pour afficher l’heure pendant le fonctionnement, appuyez sur le

bouton PROGRAM/CLOCK pendant au moins 2 secondes. Après

quelques secondes, l’afﬁ chage d’origine revient.

- En cas de panne d’électricité ou de déconnexion du câble d’

alimentation, l’affichage de l’horloge clignote. Réglez l’heure à

nouveau.

1475XEFrench.indd 181475XEFrench.indd 18 2008-7-18 13:19:242008-7-18 13:19:24

AVANT LE FONCTIONNEMENT

Mise sous tension et hors tension

Appuyez sur le bouton

/STANDBY pour mettre l’alimentation sous

tension, l’ afﬁ chage s’allume et “HELLO” apparaît brièvement.

Pour mettre l’alimentation hors tension, appuyez sur de nouveau sur le

bouton

/STANDBY. “Good bye” apparaît brièvement, puis l’afﬁ chage

de l’ horloge reste allumé.

- Lorsque le cordon d’alimentation est connecté à la sortie C.A., l’

appareil répond aux sollicitations de la télécommande.

Réglage du volume

Appuyez sur le bouton VOLUME + ou -. Le niveau de volume est indiqué

par des chiffres (VOL MIN ~ VOL MAX) sur l’afﬁ chage.

Système d’amplification des basses fréquences

dynamique

Appuyez sur le bouton DBBS pour améliorer les basses fréquences du

son. “BBS ON” apparaît sur l’écran.

Appuyez sur le bouton de nouveau, “BBS OFF” apparaît. Le son normal

reprend.

Sélection du mode sonore (Télécommande

uniquement)

Appuyez sur le bouton SOUND pour sélectionner le mode sonore qui

correspond à la musique à écouter.

CLASSIC: musique classique, etc.

ROCK: musique rock, etc.

POP: musique populaire, etc.

JAZZ:Jazz, etc.

FLAT: Normal

Sélection du mode silence (Télécommande

uniquement)

Appuyez sur le bouton MUTE une fois. “MUTE” clignote sur l’afﬁ chage,

le son est sous silence.

Appuyez de nouveau sur le bouton, “MUTE” disparaît. Le son normal

reprend.

QUE FAIRE SI ...

Si le fonctionnement de l'unité ou de l'écran n'est pas normal,

1. Appuyez sur le bouton

/STANDBY pour mettre l’alimentation hors

tension.

2. Mettez l’alimentation sous tension et reprenez les opérations.

LECTURE DE CD

Utiliser des disques compacts portant le symbole indiqué sur la Fig. 8.

En plus des CDs conventionnels de 12 cm‚ ce système peut être utilisé

pour lire des CDs de 8 cm sans adaptateur.

1. Appuyez sur la touche FUNCTION pour sélectionner la fonction “CD”.

2. Appuyez sur le couvercle du compartiment DC (la portion OPEN/

) pour l'ouvrir. Le message “OPEN” s'afﬁ che.

3. Placez le disque, étiquette vers le haut, sur le carrousel (Fig. 9). (Ne

placez qu'un disque à la fois).

4. Appuyez une autre fois sur le couvercle du compartiment DC (la

portion OPEN/CLOSE

) pour le fermer. Le message “READING”

clignote pendant plusieurs secondes, puis le nombre total de plages

et le temps de lecture total du disque s'afﬁ chent.

Remarque :

Si le disque est chargé avec l'étiquette vers le bas ou si un disque

très égratigné est chargé, le message “NO DISC” apparaît. Si cela

se produit, chargez le disque correctement ou remplacez le disque

endommagé.

5. Appuyez sur la touche

. La lecture s'amorce à la première plage.

Le numéro de la plage actuelle et le temps de lecture écoulé sont

afﬁ chés.

6. Appuyez sur la touche

pour arrêter la lecture du disque.

Après la dernière plage, le lecteur s'arrête automatiquement.

Remarques sur l’utilisation des disques compacts

- Ne pas exposer le disque aux rayons directs du soleil‚ à un taux d’

humidité élevé ou à des températures élevées pendant des périodes

prolongées.

- Les disques doivent être retournés dans leurs boîtiers après leur

utilisation.

- Ne pas coller de papier ou ne pas écrire sur la surface du disque

compact.

- Tenir le disque par ses bords. Ne pas toucher la surface de lecture

(face brillante).

- Les traces de doigt et de poussière doivent être soigneusement

essuyées de la surface de lecture du disque avec un chiffon doux.

Essuyer en faisant un mouvement droit partant du centre vers l’

extérieur du disque.

- Ne jamais utiliser des produits chimique’s tel qu’un aérosol de

nettoyage de disques‚ des aérosols antistatiques‚ ou des liquides‚ du

benzène ou un diluant pour nettoyer les disques compacts.

Pour commencer l’écoute d’une plage désirée

Sélectionnez une plage en utilisant la touche

, puis appuyez

sur la touche

Arrêt momentané de la lecture

Appuyez sur la touche

. Le temps de lecture écoulé clignote. Pour

continuer la lecture, appuyez une autre fois sur la touche.

Saut d’écoute

Pour sauter de la plage 6 pendant l’écoute de la plage 3, pressez la

touche

de façon répétitive jusqu’à ce que “06” apparaisse (dans

la section plage) sur l’afﬁ chage. Pour sauter de nouveau à la plage 3

pendant l’écoute de la plage 6, pressez la touche

de façon répétitive

jusqu’à ce que “03” apparaisse.

- Les boutons numériques de la télécommande peuvent également

être utilisés pour sauter la lecture. Pour sauter à la piste 6 pendant

la lecture d'une piste, appuyer sur 0, er ensuite sur le 6.

Ce manuel d’instructions explique les diverses fonctions de cette

unité avec la télécommande. Les boutons sur la l’unité principales

réalisent des fonctions identiques aux boutons marqués de la

télécommande.

1475XEFrench.indd 191475XEFrench.indd 19 2008-7-18 13:19:242008-7-18 13:19:24

La page charge ...

Sanyo DC-UB1475M Manuel utilisateur

Marque: Sanyo

Modèle: DC-UB1475M

Catégorie: Lecteur CD

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Sanyo DC-UB1475M User manual

Sanyo DC-UB1475M Manuel utilisateur

Sanyo DC-UB1475M Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents